summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/net/dsa/qca8k.yaml
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/net/dsa/qca8k.yaml')
-rw-r--r--Documentation/devicetree/bindings/net/dsa/qca8k.yaml306
1 files changed, 306 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/qca8k.yaml b/Documentation/devicetree/bindings/net/dsa/qca8k.yaml
new file mode 100644
index 000000000..978162df5
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/qca8k.yaml
@@ -0,0 +1,306 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/qca8k.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Atheros QCA83xx switch family
+
+maintainers:
+ - John Crispin <john@phrozen.org>
+
+description:
+ If the QCA8K switch is connect to an SoC's external mdio-bus, each subnode
+ describing a port needs to have a valid phandle referencing the internal PHY
+ it is connected to. This is because there is no N:N mapping of port and PHY
+ ID. To declare the internal mdio-bus configuration, declare an MDIO node in
+ the switch node and declare the phandle for the port, referencing the internal
+ PHY it is connected to. In this config, an internal mdio-bus is registered and
+ the MDIO master is used for communication. Mixed external and internal
+ mdio-bus configurations are not supported by the hardware.
+
+properties:
+ compatible:
+ oneOf:
+ - enum:
+ - qca,qca8327
+ - qca,qca8328
+ - qca,qca8334
+ - qca,qca8337
+ description: |
+ qca,qca8328: referenced as AR8328(N)-AK1(A/B) QFN 176 pin package
+ qca,qca8327: referenced as AR8327(N)-AL1A DR-QFN 148 pin package
+ qca,qca8334: referenced as QCA8334-AL3C QFN 88 pin package
+ qca,qca8337: referenced as QCA8337N-AL3(B/C) DR-QFN 148 pin package
+
+ reg:
+ maxItems: 1
+
+ reset-gpios:
+ description:
+ GPIO to be used to reset the whole device
+ maxItems: 1
+
+ qca,ignore-power-on-sel:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ Ignore power-on pin strapping to configure LED open-drain or EEPROM
+ presence. This is needed for devices with incorrect configuration or when
+ the OEM has decided not to use pin strapping and falls back to SW regs.
+
+ qca,led-open-drain:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ Set LEDs to open-drain mode. This requires the qca,ignore-power-on-sel to
+ be set, otherwise the driver will fail at probe. This is required if the
+ OEM does not use pin strapping to set this mode and prefers to set it
+ using SW regs. The pin strappings related to LED open-drain mode are
+ B68 on the QCA832x and B49 on the QCA833x.
+
+ mdio:
+ $ref: /schemas/net/mdio.yaml#
+ unevaluatedProperties: false
+ description: Qca8k switch have an internal mdio to access switch port.
+ If this is not present, the legacy mapping is used and the
+ internal mdio access is used.
+ With the legacy mapping the reg corresponding to the internal
+ mdio is the switch reg with an offset of -1.
+
+patternProperties:
+ "^(ethernet-)?ports$":
+ type: object
+ properties:
+ '#address-cells':
+ const: 1
+ '#size-cells':
+ const: 0
+
+ patternProperties:
+ "^(ethernet-)?port@[0-6]$":
+ type: object
+ description: Ethernet switch ports
+
+ $ref: dsa-port.yaml#
+
+ properties:
+ qca,sgmii-rxclk-falling-edge:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ Set the receive clock phase to falling edge. Mostly commonly used on
+ the QCA8327 with CPU port 0 set to SGMII.
+
+ qca,sgmii-txclk-falling-edge:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ Set the transmit clock phase to falling edge.
+
+ qca,sgmii-enable-pll:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ For SGMII CPU port, explicitly enable PLL, TX and RX chain along with
+ Signal Detection. On the QCA8327 this should not be enabled, otherwise
+ the SGMII port will not initialize. When used on the QCA8337, revision 3
+ or greater, a warning will be displayed. When the CPU port is set to
+ SGMII on the QCA8337, it is advised to set this unless a communication
+ issue is observed.
+
+ unevaluatedProperties: false
+
+oneOf:
+ - required:
+ - ports
+ - required:
+ - ethernet-ports
+
+required:
+ - compatible
+ - reg
+
+additionalProperties: true
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ external_phy_port1: ethernet-phy@0 {
+ reg = <0>;
+ };
+
+ external_phy_port2: ethernet-phy@1 {
+ reg = <1>;
+ };
+
+ external_phy_port3: ethernet-phy@2 {
+ reg = <2>;
+ };
+
+ external_phy_port4: ethernet-phy@3 {
+ reg = <3>;
+ };
+
+ external_phy_port5: ethernet-phy@4 {
+ reg = <4>;
+ };
+
+ switch@10 {
+ compatible = "qca,qca8337";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+ reg = <0x10>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ ethernet = <&gmac1>;
+ phy-mode = "rgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ phy-handle = <&external_phy_port1>;
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ phy-handle = <&external_phy_port2>;
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ phy-handle = <&external_phy_port3>;
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan4";
+ phy-handle = <&external_phy_port4>;
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "wan";
+ phy-handle = <&external_phy_port5>;
+ };
+ };
+ };
+ };
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch@10 {
+ compatible = "qca,qca8337";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reset-gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
+ reg = <0x10>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ ethernet = <&gmac1>;
+ phy-mode = "rgmii";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ phy-mode = "internal";
+ phy-handle = <&internal_phy_port1>;
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ phy-mode = "internal";
+ phy-handle = <&internal_phy_port2>;
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ phy-mode = "internal";
+ phy-handle = <&internal_phy_port3>;
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan4";
+ phy-mode = "internal";
+ phy-handle = <&internal_phy_port4>;
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "wan";
+ phy-mode = "internal";
+ phy-handle = <&internal_phy_port5>;
+ };
+
+ port@6 {
+ reg = <0>;
+ ethernet = <&gmac1>;
+ phy-mode = "sgmii";
+
+ qca,sgmii-rxclk-falling-edge;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ internal_phy_port1: ethernet-phy@0 {
+ reg = <0>;
+ };
+
+ internal_phy_port2: ethernet-phy@1 {
+ reg = <1>;
+ };
+
+ internal_phy_port3: ethernet-phy@2 {
+ reg = <2>;
+ };
+
+ internal_phy_port4: ethernet-phy@3 {
+ reg = <3>;
+ };
+
+ internal_phy_port5: ethernet-phy@4 {
+ reg = <4>;
+ };
+ };
+ };
+ };