summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/net/dsa/realtek.yaml
diff options
context:
space:
mode:
Diffstat (limited to '')
-rw-r--r--Documentation/devicetree/bindings/net/dsa/realtek.yaml386
1 files changed, 386 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/realtek.yaml b/Documentation/devicetree/bindings/net/dsa/realtek.yaml
new file mode 100644
index 000000000..1a7d45a8a
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/realtek.yaml
@@ -0,0 +1,386 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/realtek.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Realtek switches for unmanaged switches
+
+allOf:
+ - $ref: dsa.yaml#
+
+maintainers:
+ - Linus Walleij <linus.walleij@linaro.org>
+
+description:
+ Realtek advertises these chips as fast/gigabit switches or unmanaged
+ switches. They can be controlled using different interfaces, like SMI,
+ MDIO or SPI.
+
+ The SMI "Simple Management Interface" is a two-wire protocol using
+ bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does
+ not use the MDIO protocol. This binding defines how to specify the
+ SMI-based Realtek devices. The realtek-smi driver is a platform driver
+ and it must be inserted inside a platform node.
+
+ The MDIO-connected switches use MDIO protocol to access their registers.
+ The realtek-mdio driver is an MDIO driver and it must be inserted inside
+ an MDIO node.
+
+ The compatible string is only used to identify which (silicon) family the
+ switch belongs to. Roughly speaking, a family is any set of Realtek switches
+ whose chip identification register(s) have a common location and semantics.
+ The different models in a given family can be automatically disambiguated by
+ parsing the chip identification register(s) according to the given family,
+ avoiding the need for a unique compatible string for each model.
+
+properties:
+ compatible:
+ enum:
+ - realtek,rtl8365mb
+ - realtek,rtl8366rb
+ description: |
+ realtek,rtl8365mb:
+ Use with models RTL8363NB, RTL8363NB-VB, RTL8363SC, RTL8363SC-VB,
+ RTL8364NB, RTL8364NB-VB, RTL8365MB, RTL8366SC, RTL8367RB-VB, RTL8367S,
+ RTL8367SB, RTL8370MB, RTL8310SR
+ realtek,rtl8366rb:
+ Use with models RTL8366RB, RTL8366S
+
+ mdc-gpios:
+ description: GPIO line for the MDC clock line.
+ maxItems: 1
+
+ mdio-gpios:
+ description: GPIO line for the MDIO data line.
+ maxItems: 1
+
+ reset-gpios:
+ description: GPIO to be used to reset the whole device
+ maxItems: 1
+
+ realtek,disable-leds:
+ type: boolean
+ description: |
+ if the LED drivers are not used in the hardware design,
+ this will disable them so they are not turned on
+ and wasting power.
+
+ interrupt-controller:
+ type: object
+ description: |
+ This defines an interrupt controller with an IRQ line (typically
+ a GPIO) that will demultiplex and handle the interrupt from the single
+ interrupt line coming out of one of the Realtek switch chips. It most
+ importantly provides link up/down interrupts to the PHY blocks inside
+ the ASIC.
+
+ properties:
+
+ interrupt-controller: true
+
+ interrupts:
+ maxItems: 1
+ description:
+ A single IRQ line from the switch, either active LOW or HIGH
+
+ '#address-cells':
+ const: 0
+
+ '#interrupt-cells':
+ const: 1
+
+ required:
+ - interrupt-controller
+ - '#address-cells'
+ - '#interrupt-cells'
+
+ mdio:
+ $ref: /schemas/net/mdio.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ compatible:
+ const: realtek,smi-mdio
+
+if:
+ required:
+ - reg
+
+then:
+ $ref: /schemas/spi/spi-peripheral-props.yaml#
+ not:
+ required:
+ - mdc-gpios
+ - mdio-gpios
+ - mdio
+
+ properties:
+ mdc-gpios: false
+ mdio-gpios: false
+ mdio: false
+
+else:
+ required:
+ - mdc-gpios
+ - mdio-gpios
+ - mdio
+ - reset-gpios
+
+required:
+ - compatible
+
+ # - mdc-gpios
+ # - mdio-gpios
+ # - reset-gpios
+ # - mdio
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ platform {
+ switch {
+ compatible = "realtek,rtl8366rb";
+ /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */
+ mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+ mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+
+ switch_intc1: interrupt-controller {
+ /* GPIO 15 provides the interrupt */
+ interrupt-parent = <&gpio0>;
+ interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ label = "lan0";
+ phy-handle = <&phy0>;
+ };
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ phy-handle = <&phy1>;
+ };
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ phy-handle = <&phy2>;
+ };
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ phy-handle = <&phy3>;
+ };
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ phy-handle = <&phy4>;
+ };
+ port@5 {
+ reg = <5>;
+ ethernet = <&gmac0>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+
+ mdio {
+ compatible = "realtek,smi-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ interrupt-parent = <&switch_intc1>;
+ interrupts = <0>;
+ };
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ interrupt-parent = <&switch_intc1>;
+ interrupts = <1>;
+ };
+ phy2: ethernet-phy@2 {
+ reg = <2>;
+ interrupt-parent = <&switch_intc1>;
+ interrupts = <2>;
+ };
+ phy3: ethernet-phy@3 {
+ reg = <3>;
+ interrupt-parent = <&switch_intc1>;
+ interrupts = <3>;
+ };
+ phy4: ethernet-phy@4 {
+ reg = <4>;
+ interrupt-parent = <&switch_intc1>;
+ interrupts = <12>;
+ };
+ };
+ };
+ };
+
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ platform {
+ switch {
+ compatible = "realtek,rtl8365mb";
+ mdc-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+ mdio-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+
+ switch_intc2: interrupt-controller {
+ interrupt-parent = <&gpio5>;
+ interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ label = "swp0";
+ phy-handle = <&ethphy0>;
+ };
+ port@1 {
+ reg = <1>;
+ label = "swp1";
+ phy-handle = <&ethphy1>;
+ };
+ port@2 {
+ reg = <2>;
+ label = "swp2";
+ phy-handle = <&ethphy2>;
+ };
+ port@3 {
+ reg = <3>;
+ label = "swp3";
+ phy-handle = <&ethphy3>;
+ };
+ port@6 {
+ reg = <6>;
+ ethernet = <&fec1>;
+ phy-mode = "rgmii";
+ tx-internal-delay-ps = <2000>;
+ rx-internal-delay-ps = <2000>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+
+ mdio {
+ compatible = "realtek,smi-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ interrupt-parent = <&switch_intc2>;
+ interrupts = <0>;
+ };
+ ethphy1: ethernet-phy@1 {
+ reg = <1>;
+ interrupt-parent = <&switch_intc2>;
+ interrupts = <1>;
+ };
+ ethphy2: ethernet-phy@2 {
+ reg = <2>;
+ interrupt-parent = <&switch_intc2>;
+ interrupts = <2>;
+ };
+ ethphy3: ethernet-phy@3 {
+ reg = <3>;
+ interrupt-parent = <&switch_intc2>;
+ interrupts = <3>;
+ };
+ };
+ };
+ };
+
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch@29 {
+ compatible = "realtek,rtl8365mb";
+ reg = <29>;
+
+ reset-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
+
+ switch_intc3: interrupt-controller {
+ interrupt-parent = <&gpio0>;
+ interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan4";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan3";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan1";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ };
+
+ port@7 {
+ reg = <7>;
+ ethernet = <&ethernet>;
+ phy-mode = "rgmii";
+ tx-internal-delay-ps = <2000>;
+ rx-internal-delay-ps = <0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };