summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/net/mdio.yaml
diff options
context:
space:
mode:
Diffstat (limited to '')
-rw-r--r--Documentation/devicetree/bindings/net/mdio.yaml116
1 files changed, 116 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/mdio.yaml b/Documentation/devicetree/bindings/net/mdio.yaml
new file mode 100644
index 000000000..b5706d4e7
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/mdio.yaml
@@ -0,0 +1,116 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/mdio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MDIO Bus Generic Binding
+
+maintainers:
+ - Andrew Lunn <andrew@lunn.ch>
+ - Florian Fainelli <f.fainelli@gmail.com>
+ - Heiner Kallweit <hkallweit1@gmail.com>
+
+description:
+ These are generic properties that can apply to any MDIO bus. Any
+ MDIO bus must have a list of child nodes, one per device on the
+ bus. These should follow the generic ethernet-phy.yaml document, or
+ a device specific binding document.
+
+properties:
+ $nodename:
+ pattern: "^mdio(@.*)?"
+
+ "#address-cells":
+ const: 1
+
+ "#size-cells":
+ const: 0
+
+ reset-gpios:
+ maxItems: 1
+ description:
+ The phandle and specifier for the GPIO that controls the RESET
+ lines of all devices on that MDIO bus.
+
+ reset-delay-us:
+ description:
+ RESET pulse width in microseconds. It applies to all MDIO devices
+ and must therefore be appropriately determined based on all devices
+ requirements (maximum value of all per-device RESET pulse widths).
+
+ reset-post-delay-us:
+ description:
+ Delay after reset deassert in microseconds. It applies to all MDIO
+ devices and it's determined by how fast all devices are ready for
+ communication. This delay happens just before e.g. Ethernet PHY
+ type ID auto detection.
+
+ clock-frequency:
+ description:
+ Desired MDIO bus clock frequency in Hz. Values greater than IEEE 802.3
+ defined 2.5MHz should only be used when all devices on the bus support
+ the given clock speed.
+
+ suppress-preamble:
+ description:
+ The 32 bit preamble should be suppressed. In order for this to
+ work, all devices on the bus must support suppressed preamble.
+ type: boolean
+
+patternProperties:
+ '@[0-9a-f]+$':
+ type: object
+
+ properties:
+ reg:
+ minimum: 0
+ maximum: 31
+ description:
+ The ID number for the device.
+
+ broken-turn-around:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ If set, indicates the MDIO device does not correctly release
+ the turn around line low at end of the control phase of the
+ MDIO transaction.
+
+ reset-gpios:
+ maxItems: 1
+ description:
+ The GPIO phandle and specifier for the MDIO reset signal.
+
+ reset-assert-us:
+ description:
+ Delay after the reset was asserted in microseconds. If this
+ property is missing the delay will be skipped.
+
+ reset-deassert-us:
+ description:
+ Delay after the reset was deasserted in microseconds. If
+ this property is missing the delay will be skipped.
+
+ required:
+ - reg
+
+additionalProperties: true
+
+examples:
+ - |
+ davinci_mdio: mdio@5c030000 {
+ reg = <0x5c030000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ reset-gpios = <&gpio2 5 1>;
+ reset-delay-us = <2>;
+
+ ethphy0: ethernet-phy@1 {
+ reg = <1>;
+ };
+
+ ethphy1: ethernet-phy@3 {
+ reg = <3>;
+ };
+ };