diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/net/mediatek-bluetooth.txt | 116 |
1 files changed, 116 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt b/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt new file mode 100644 index 000000000..9ef5bacda --- /dev/null +++ b/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt @@ -0,0 +1,116 @@ +MediaTek SoC built-in Bluetooth Devices +================================== + +This device is a serial attached device to BTIF device and thus it must be a +child node of the serial node with BTIF. The dt-bindings details for BTIF +device can be known via Documentation/devicetree/bindings/serial/8250.yaml. + +Required properties: + +- compatible: Must be + "mediatek,mt7622-bluetooth": for MT7622 SoC +- clocks: Should be the clock specifiers corresponding to the entry in + clock-names property. +- clock-names: Should contain "ref" entries. +- power-domains: Phandle to the power domain that the device is part of + +Example: + + btif: serial@1100c000 { + compatible = "mediatek,mt7622-btif", + "mediatek,mtk-btif"; + reg = <0 0x1100c000 0 0x1000>; + interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_BTIF_PD>; + clock-names = "main"; + reg-shift = <2>; + reg-io-width = <4>; + + bluetooth { + compatible = "mediatek,mt7622-bluetooth"; + power-domains = <&scpsys MT7622_POWER_DOMAIN_WB>; + clocks = <&clk25m>; + clock-names = "ref"; + }; + }; + +MediaTek UART based Bluetooth Devices +================================== + +This device is a serial attached device to UART device and thus it must be a +child node of the serial node with UART. + +Please refer to the following documents for generic properties: + + Documentation/devicetree/bindings/serial/serial.yaml + +Required properties: + +- compatible: Must be + "mediatek,mt7663u-bluetooth": for MT7663U device + "mediatek,mt7668u-bluetooth": for MT7668U device +- vcc-supply: Main voltage regulator + +If the pin controller on the platform can support both pinmux and GPIO +control such as the most of MediaTek platform. Please use below properties. + +- pinctrl-names: Should be "default", "runtime" +- pinctrl-0: Should contain UART RXD low when the device is powered up to + enter proper bootstrap mode. +- pinctrl-1: Should contain UART mode pin ctrl + +Else, the pin controller on the platform only can support pinmux control and +the GPIO control still has to rely on the dedicated GPIO controller such as +a legacy MediaTek SoC, MT7621. Please use the below properties. + +- boot-gpios: GPIO same to the pin as UART RXD and used to keep LOW when + the device is powered up to enter proper bootstrap mode when +- pinctrl-names: Should be "default" +- pinctrl-0: Should contain UART mode pin ctrl + +Optional properties: + +- reset-gpios: GPIO used to reset the device whose initial state keeps low, + if the GPIO is missing, then board-level design should be + guaranteed. +- clocks: Should be the clock specifiers corresponding to the entry in + clock-names property. If the clock is missing, then board-level + design should be guaranteed. +- clock-names: Should contain "osc" entry for the external oscillator. +- current-speed: Current baud rate of the device whose defaults to 921600 + +Example: + + uart1_pins_boot: uart1-default { + pins-dat { + pinmux = <MT7623_PIN_81_URXD1_FUNC_GPIO81>; + output-low; + }; + }; + + uart1_pins_runtime: uart1-runtime { + pins-dat { + pinmux = <MT7623_PIN_81_URXD1_FUNC_URXD1>, + <MT7623_PIN_82_UTXD1_FUNC_UTXD1>; + }; + }; + + uart1: serial@11003000 { + compatible = "mediatek,mt7623-uart", + "mediatek,mt6577-uart"; + reg = <0 0x11003000 0 0x400>; + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pericfg CLK_PERI_UART1_SEL>, + <&pericfg CLK_PERI_UART1>; + clock-names = "baud", "bus"; + + bluetooth { + compatible = "mediatek,mt7663u-bluetooth"; + vcc-supply = <®_5v>; + reset-gpios = <&pio 24 GPIO_ACTIVE_LOW>; + pinctrl-names = "default", "runtime"; + pinctrl-0 = <&uart1_pins_boot>; + pinctrl-1 = <&uart1_pins_runtime>; + current-speed = <921600>; + }; + }; |