diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml | 150 |
1 files changed, 150 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml b/Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml new file mode 100644 index 000000000..fec1cc9b9 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/brcm,bcm4329-fmac.yaml @@ -0,0 +1,150 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/wireless/brcm,bcm4329-fmac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom BCM4329 family fullmac wireless SDIO/PCIE devices + +maintainers: + - Arend van Spriel <arend@broadcom.com> + +description: + The Broadcom Single chip MAC part for the BCM4329 family and + later Cypress chips in the same family named CYW4373 and similar. + These chips also have a Bluetooth portion described in a separate + binding. + +properties: + compatible: + oneOf: + - items: + - enum: + - brcm,bcm43143-fmac + - brcm,bcm4341b0-fmac + - brcm,bcm4341b4-fmac + - brcm,bcm4341b5-fmac + - brcm,bcm4329-fmac + - brcm,bcm4330-fmac + - brcm,bcm4334-fmac + - brcm,bcm43340-fmac + - brcm,bcm4335-fmac + - brcm,bcm43362-fmac + - brcm,bcm4339-fmac + - brcm,bcm43430a0-fmac + - brcm,bcm43430a1-fmac + - brcm,bcm43455-fmac + - brcm,bcm43456-fmac + - brcm,bcm4354-fmac + - brcm,bcm4356-fmac + - brcm,bcm4359-fmac + - cypress,cyw4373-fmac + - cypress,cyw43012-fmac + - const: brcm,bcm4329-fmac + - enum: + - brcm,bcm4329-fmac + - pci14e4,43dc # BCM4355 + - pci14e4,4464 # BCM4364 + - pci14e4,4488 # BCM4377 + - pci14e4,4425 # BCM4378 + - pci14e4,4433 # BCM4387 + + reg: + description: SDIO function number for the device (for most cases + this will be 1) or PCI device identifier. + + interrupts: + maxItems: 1 + description: Out-of-band (OOB) IRQ line for waking up the host + in response to WLAN activity. This corresponds to the HOST_WAKE + line into the chip. + + interrupt-names: + description: Name for the OOB IRQ, this must be set to "host-wake". + const: host-wake + + brcm,drive-strength: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Drive strength used for the SDIO pins on the device in mA. + minimum: 0 + maximum: 32 + + reset-gpios: + maxItems: 1 + description: A GPIO line connected to the WL_RST line, if present + this shall be flagged as active low. + + brcm,ccode-map: + $ref: /schemas/types.yaml#/definitions/string-array + description: Multiple strings for translating ISO3166 country code to + brcmfmac firmware country code and revision. + items: + pattern: '^[A-Z][A-Z]-[A-Z][0-9A-Z]-[0-9]+$' + + brcm,ccode-map-trivial: + description: | + Use a trivial mapping of ISO3166 country codes to brcmfmac firmware + country code and revision: cc -> { cc, 0 }. In other words, assume that + the CLM blob firmware uses ISO3166 country codes as well, and that all + revisions are zero. This property is mutually exclusive with + brcm,ccode-map. If both properties are specified, then brcm,ccode-map + takes precedence. + type: boolean + + brcm,cal-blob: + $ref: /schemas/types.yaml#/definitions/uint8-array + description: A per-device calibration blob for the Wi-Fi radio. This + should be filled in by the bootloader from platform configuration + data, if necessary, and will be uploaded to the device if present. + + brcm,board-type: + $ref: /schemas/types.yaml#/definitions/string + description: Overrides the board type, which is normally the compatible of + the root node. This can be used to decouple the overall system board or + device name from the board type for WiFi purposes, which is used to + construct firmware and NVRAM configuration filenames, allowing for + multiple devices that share the same module or characteristics for the + WiFi subsystem to share the same firmware/NVRAM files. On Apple platforms, + this should be the Apple module-instance codename prefixed by "apple,", + e.g. "apple,honshu". + + apple,antenna-sku: + $ref: /schemas/types.yaml#/definitions/string + description: Antenna SKU used to identify a specific antenna configuration + on Apple platforms. This is use to build firmware filenames, to allow + platforms with different antenna configs to have different firmware and/or + NVRAM. This would normally be filled in by the bootloader from platform + configuration data. + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + mmc@80118000 { + compatible = "arm,pl18x", "arm,primecell"; + reg = <0x80118000 0x1000>; + clocks = <&clk 0>, <&clk 1>; + clock-names = "mclk", "apb_pclk"; + interrupts = <0 60 IRQ_TYPE_LEVEL_HIGH>; + bus-width = <4>; + non-removable; + vmmc-supply = <&wl_bt_reg>; + #address-cells = <1>; + #size-cells = <0>; + + wifi@1 { + compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac"; + reg = <1>; + interrupt-parent = <&gpio>; + interrupts = <24 IRQ_TYPE_EDGE_FALLING>; + interrupt-names = "host-wake"; + reset-gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + brcm,ccode-map = "JP-JP-78", "US-Q2-86"; + }; + }; |