diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci/ralink,rt3883-pci.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/pci/ralink,rt3883-pci.txt | 187 |
1 files changed, 187 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pci/ralink,rt3883-pci.txt b/Documentation/devicetree/bindings/pci/ralink,rt3883-pci.txt new file mode 100644 index 000000000..ffba4f63d --- /dev/null +++ b/Documentation/devicetree/bindings/pci/ralink,rt3883-pci.txt @@ -0,0 +1,187 @@ +* Mediatek/Ralink RT3883 PCI controller + +1) Main node + + Required properties: + + - compatible: must be "ralink,rt3883-pci" + + - reg: specifies the physical base address of the controller and + the length of the memory mapped region. + + - #address-cells: specifies the number of cells needed to encode an + address. The value must be 1. + + - #size-cells: specifies the number of cells used to represent the size + of an address. The value must be 1. + + - ranges: specifies the translation between child address space and parent + address space + + Optional properties: + + - status: indicates the operational status of the device. + Value must be either "disabled" or "okay". + +2) Child nodes + + The main node must have two child nodes which describes the built-in + interrupt controller and the PCI host bridge. + + a) Interrupt controller: + + Required properties: + + - interrupt-controller: identifies the node as an interrupt controller + + - #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. As such, 'interrupt-map' nodes do not + have to specify a parent unit address. + + - #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. + + - interrupts: specifies the interrupt source of the parent interrupt + controller. The format of the interrupt specifier depends on the + parent interrupt controller. + + b) PCI host bridge: + + Required properties: + + - #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. + + - #size-cells: specifies the number of cells used to represent the size + of an address. The value must be 2. + + - #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. + + - device_type: must be "pci" + + - bus-range: PCI bus numbers covered + + - ranges: specifies the ranges for the PCI memory and I/O regions + + - interrupt-map-mask, + - interrupt-map: standard PCI properties to define the mapping of the + PCI interface to interrupt numbers. + + The PCI host bridge node might have additional sub-nodes representing + the onboard PCI devices/PCI slots. Each such sub-node must have the + following mandatory properties: + + - reg: used only for interrupt mapping, so only the first four bytes + are used to refer to the correct bus number and device number. + + - device_type: must be "pci" + + If a given sub-node represents a PCI bridge it must have following + mandatory properties as well: + + - #address-cells: must be set to <3> + + - #size-cells: must set to <2> + + - #interrupt-cells: must be set to <1> + + - interrupt-map-mask, + - interrupt-map: standard PCI properties to define the mapping of the + PCI interface to interrupt numbers. + + Besides the required properties the sub-nodes may have these optional + properties: + + - status: indicates the operational status of the sub-node. + Value must be either "disabled" or "okay". + +3) Example: + + a) SoC specific dtsi file: + + pci@10140000 { + compatible = "ralink,rt3883-pci"; + reg = <0x10140000 0x20000>; + #address-cells = <1>; + #size-cells = <1>; + ranges; /* direct mapping */ + + status = "disabled"; + + pciintc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + + interrupt-parent = <&cpuintc>; + interrupts = <4>; + }; + + host-bridge { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + + device_type = "pci"; + + bus-range = <0 255>; + ranges = < + 0x02000000 0 0x00000000 0x20000000 0 0x10000000 /* pci memory */ + 0x01000000 0 0x00000000 0x10160000 0 0x00010000 /* io space */ + >; + + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = < + /* IDSEL 17 */ + 0x8800 0 0 1 &pciintc 18 + 0x8800 0 0 2 &pciintc 18 + 0x8800 0 0 3 &pciintc 18 + 0x8800 0 0 4 &pciintc 18 + /* IDSEL 18 */ + 0x9000 0 0 1 &pciintc 19 + 0x9000 0 0 2 &pciintc 19 + 0x9000 0 0 3 &pciintc 19 + 0x9000 0 0 4 &pciintc 19 + >; + + pci-bridge@1 { + reg = <0x0800 0 0 0 0>; + device_type = "pci"; + #interrupt-cells = <1>; + #address-cells = <3>; + #size-cells = <2>; + + interrupt-map-mask = <0x0 0 0 0>; + interrupt-map = <0x0 0 0 0 &pciintc 20>; + + status = "disabled"; + }; + + pci-slot@17 { + reg = <0x8800 0 0 0 0>; + device_type = "pci"; + + status = "disabled"; + }; + + pci-slot@18 { + reg = <0x9000 0 0 0 0>; + device_type = "pci"; + + status = "disabled"; + }; + }; + }; + + b) Board specific dts file: + + pci@10140000 { + status = "okay"; + + host-bridge { + pci-bridge@1 { + status = "okay"; + }; + }; + }; |