1 files changed, 94 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt
new file mode 100644
index 000000000..8146193bd
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt
@@ -0,0 +1,94 @@
+== Amlogic Meson pinmux controller ==
+
+Required properties for the root node:
+ - compatible: one of "amlogic,meson8-cbus-pinctrl"
+		      "amlogic,meson8b-cbus-pinctrl"
+		      "amlogic,meson8m2-cbus-pinctrl"
+		      "amlogic,meson8-aobus-pinctrl"
+		      "amlogic,meson8b-aobus-pinctrl"
+		      "amlogic,meson8m2-aobus-pinctrl"
+		      "amlogic,meson-gxbb-periphs-pinctrl"
+		      "amlogic,meson-gxbb-aobus-pinctrl"
+		      "amlogic,meson-gxl-periphs-pinctrl"
+		      "amlogic,meson-gxl-aobus-pinctrl"
+		      "amlogic,meson-axg-periphs-pinctrl"
+		      "amlogic,meson-axg-aobus-pinctrl"
+		      "amlogic,meson-g12a-periphs-pinctrl"
+		      "amlogic,meson-g12a-aobus-pinctrl"
+		      "amlogic,meson-a1-periphs-pinctrl"
+		      "amlogic,meson-s4-periphs-pinctrl"
+ - reg: address and size of registers controlling irq functionality
+
+=== GPIO sub-nodes ===
+
+The GPIO bank for the controller is represented as a sub-node and it acts as a
+GPIO controller.
+
+Required properties for sub-nodes are:
+ - reg: should contain a list of address and size, one tuple for each entry
+   in reg-names.
+ - reg-names: an array of strings describing the "reg" entries.
+   Must contain "mux" and "gpio".
+   May contain "pull", "pull-enable" and "ds" when appropriate.
+ - gpio-controller: identifies the node as a gpio controller
+ - #gpio-cells: must be 2
+
+=== Other sub-nodes ===
+
+Child nodes without the "gpio-controller" represent some desired
+configuration for a pin or a group. Those nodes can be pinmux nodes or
+configuration nodes.
+
+Required properties for pinmux nodes are:
+ - groups: a list of pinmux groups. The list of all available groups
+   depends on the SoC and can be found in driver sources.
+ - function: the name of a function to activate for the specified set
+   of groups. The list of all available functions depends on the SoC
+   and can be found in driver sources.
+
+Required properties for configuration nodes:
+ - pins: a list of pin names
+
+Configuration nodes support the following generic properties, as
+described in file pinctrl-bindings.txt:
+ - "bias-disable"
+ - "bias-pull-up"
+ - "bias-pull-down"
+ - "output-enable"
+ - "output-disable"
+ - "output-low"
+ - "output-high"
+
+Optional properties :
+ - drive-strength-microamp: Drive strength for the specified pins in uA.
+			    This property is only valid for G12A and newer.
+
+=== Example ===
+
+	pinctrl: pinctrl@c1109880 {
+		compatible = "amlogic,meson8-cbus-pinctrl";
+		reg = <0xc1109880 0x10>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gpio: banks@c11080b0 {
+			reg = <0xc11080b0 0x28>,
+			      <0xc11080e8 0x18>,
+			      <0xc1108120 0x18>,
+			      <0xc1108030 0x30>;
+			reg-names = "mux", "pull", "pull-enable", "gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+               };
+
+		nand {
+			mux {
+				groups = "nand_io", "nand_io_ce0", "nand_io_ce1",
+					 "nand_io_rb0", "nand_ale", "nand_cle",
+					 "nand_wen_clk", "nand_ren_clk", "nand_dqs",
+					 "nand_ce2", "nand_ce3";
+				function = "nand";
+			};
+		};
+	};