diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml | 153 |
1 files changed, 153 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml b/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml new file mode 100644 index 000000000..f5a121311 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pincfg-node.yaml @@ -0,0 +1,153 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/pincfg-node.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Generic pin configuration node schema + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + +description: + Many data items that are represented in a pin configuration node are common + and generic. Pin control bindings should use the properties defined below + where they are applicable; not all of these properties are relevant or useful + for all hardware or binding structures. Each individual binding document + should state which of these generic properties, if any, are used, and the + structure of the DT nodes that contain these properties. + +properties: + bias-disable: + type: boolean + description: disable any pin bias + + bias-high-impedance: + type: boolean + description: high impedance mode ("third-state", "floating") + + bias-bus-hold: + type: boolean + description: latch weakly + + bias-pull-up: + oneOf: + - type: boolean + - $ref: /schemas/types.yaml#/definitions/uint32 + description: pull up the pin. Takes as optional argument on hardware + supporting it the pull strength in Ohm. + + bias-pull-down: + oneOf: + - type: boolean + - $ref: /schemas/types.yaml#/definitions/uint32 + description: pull down the pin. Takes as optional argument on hardware + supporting it the pull strength in Ohm. + + bias-pull-pin-default: + oneOf: + - type: boolean + - $ref: /schemas/types.yaml#/definitions/uint32 + description: use pin-default pull state. Takes as optional argument on + hardware supporting it the pull strength in Ohm. + + drive-push-pull: + oneOf: + - type: boolean + - $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1 ] + deprecated: true + description: drive actively high and low + + drive-open-drain: + oneOf: + - type: boolean + - $ref: /schemas/types.yaml#/definitions/uint32 + const: 1 # No known cases of 0 + deprecated: true + description: drive with open drain + + drive-open-source: + type: boolean + description: drive with open source + + drive-strength: + $ref: /schemas/types.yaml#/definitions/uint32 + description: sink or source at most X mA + + drive-strength-microamp: + description: sink or source at most X uA + + input-enable: + type: boolean + description: enable input on pin (no effect on output, such as + enabling an input buffer) + + input-disable: + type: boolean + description: disable input on pin (no effect on output, such as + disabling an input buffer) + + input-schmitt-enable: + type: boolean + description: enable schmitt-trigger mode + + input-schmitt-disable: + type: boolean + description: disable schmitt-trigger mode + + input-debounce: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Takes the debounce time in usec as argument or 0 to disable + debouncing + + power-source: + $ref: /schemas/types.yaml#/definitions/uint32 + description: select between different power supplies + + low-power-enable: + type: boolean + description: enable low power mode + + low-power-disable: + type: boolean + description: disable low power mode + + output-disable: + type: boolean + description: disable output on a pin (such as disable an output buffer) + + output-enable: + type: boolean + description: enable output on a pin without actively driving it + (such as enabling an output buffer) + + output-impedance-ohms: + description: set the output impedance of a pin to at most X ohms + + output-low: + type: boolean + description: set the pin to output mode with low level + + output-high: + type: boolean + description: set the pin to output mode with high level + + sleep-hardware-state: + type: boolean + description: indicate this is sleep related state which will be + programmed into the registers for the sleep state. + + slew-rate: + $ref: /schemas/types.yaml#/definitions/uint32 + description: set the slew rate + + skew-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + this affects the expected clock skew on input pins + and the delay before latching a value to an output + pin. Typically indicates how many double-inverters are + used to delay the signal. + +additionalProperties: true |