diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt | 105 |
1 files changed, 105 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt new file mode 100644 index 000000000..c28d4eb83 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-palmas.txt @@ -0,0 +1,105 @@ +Palmas Pincontrol bindings + +The pins of Palmas device can be set on different option and provides +the configuration for Pull UP/DOWN, open drain etc. + +Required properties: +- compatible: It must be one of following: + - "ti,palmas-pinctrl" for Palma series of the pincontrol. + - "ti,tps65913-pinctrl" for Palma series device TPS65913. + - "ti,tps80036-pinctrl" for Palma series device TPS80036. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +Palmas's pin configuration nodes act as a container for an arbitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +list of pins. This configuration can include the mux function to select on +those pin(s), and various pin configuration parameters, such as pull-up, +open drain. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + +Optional properties: +- ti,palmas-enable-dvfs1: Enable DVFS1. Configure pins for DVFS1 mode. + Selection primary or secondary function associated to I2C2_SCL_SCE, + I2C2_SDA_SDO pin/pad for DVFS1 interface +- ti,palmas-enable-dvfs2: Enable DVFS2. Configure pins for DVFS2 mode. + Selection primary or secondary function associated to GPADC_START + and SYSEN2 pin/pad for DVFS2 interface +- ti,palmas-override-powerhold: This is applicable for PMICs for which + GPIO7 is configured in POWERHOLD mode which has higher priority + over DEV_ON bit and keeps the PMIC supplies on even after the DEV_ON + bit is turned off. This property enables driver to over ride the + POWERHOLD value to GPIO7 so as to turn off the PMIC in power off + scenarios. So for GPIO7 if ti,palmas-override-powerhold is set + then the GPIO_7 field should never be muxed to anything else. + It should be set to POWERHOLD by default and only in case of + power off scenarios the driver will over ride the mux value. + +This binding uses the following generic properties as defined in +pinctrl-bindings.txt: + +Required: pins +Options: function, bias-disable, bias-pull-up, bias-pull-down, + drive-open-drain. + +Note that many of these properties are only valid for certain specific pins. +See the Palmas device datasheet for complete details regarding which pins +support which functionality. + +Valid values for pin names are: + gpio0, gpio1, gpio2, gpio3, gpio4, gpio5, gpio6, gpio7, gpio8, gpio9, + gpio10, gpio11, gpio12, gpio13, gpio14, gpio15, vac, powergood, + nreswarm, pwrdown, gpadc_start, reset_in, nsleep, enable1, enable2, + int. + +Valid value of function names are: + gpio, led, pwm, regen, sysen, clk32kgaudio, id, vbus_det, chrg_det, + vac, vacok, powergood, usb_psel, msecure, pwrhold, int, nreswarm, + simrsto, simrsti, low_vbat, wireless_chrg1, rcm, pwrdown, gpadc_start, + reset_in, nsleep, enable. + +There are 4 special functions: opt0, opt1, opt2 and opt3. If any of these +functions is selected then directly pins register will be written with 0, 1, 2 +or 3 respectively if it is valid for that pins or list of pins. + +Example: + palmas: tps65913 { + .... + pinctrl { + compatible = "ti,tps65913-pinctrl"; + ti,palmas-enable-dvfs1; + pinctrl-names = "default"; + pinctrl-0 = <&palmas_pins_state>; + + palmas_pins_state: pinmux { + gpio0 { + pins = "gpio0"; + function = "id"; + bias-pull-up; + }; + + vac { + pins = "vac"; + function = "vacok"; + bias-pull-down; + }; + + gpio5 { + pins = "gpio5"; + function = "opt0"; + drive-open-drain = <1>; + }; + }; + }; + .... + }; |