diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm-hc.yaml | 149 |
1 files changed, 149 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm-hc.yaml b/Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm-hc.yaml new file mode 100644 index 000000000..8273ac55b --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/qcom-spmi-adc-tm-hc.yaml @@ -0,0 +1,149 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/thermal/qcom-spmi-adc-tm-hc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm's SPMI PMIC ADC HC Thermal Monitoring +maintainers: + - Dmitry Baryshkov <dmitry.baryshkov@linaro.org> + +properties: + compatible: + const: qcom,spmi-adc-tm-hc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + "#thermal-sensor-cells": + const: 1 + description: + Number of cells required to uniquely identify the thermal sensors. Since + we have multiple sensors this is set to 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + qcom,avg-samples: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Number of samples to be used for measurement. + enum: + - 1 + - 2 + - 4 + - 8 + - 16 + default: 1 + + qcom,decimation: + $ref: /schemas/types.yaml#/definitions/uint32 + description: This parameter is used to decrease ADC sampling rate. + Quicker measurements can be made by reducing decimation ratio. + enum: + - 256 + - 512 + - 1024 + default: 1024 + +patternProperties: + "^([-a-z0-9]*)@[0-7]$": + type: object + description: + Represent one thermal sensor. + + properties: + reg: + description: Specify the sensor channel. There are 8 channels in PMIC5's ADC TM + minimum: 0 + maximum: 7 + + io-channels: + description: + From common IIO binding. Used to pipe PMIC ADC channel to thermal monitor + + qcom,ratiometric: + $ref: /schemas/types.yaml#/definitions/flag + description: + Channel calibration type. + If this property is specified VADC will use the VDD reference + (1.875V) and GND for channel calibration. If property is not found, + channel will be calibrated with 0V and 1.25V reference channels, + also known as absolute calibration. + + qcom,hw-settle-time-us: + description: Time between AMUX getting configured and the ADC starting conversion. + enum: [0, 100, 200, 300, 400, 500, 600, 700, 1000, 2000, 4000, 6000, 8000, 10000] + + qcom,pre-scaling: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: Used for scaling the channel input signal before the + signal is fed to VADC. The configuration for this node is to know the + pre-determined ratio and use it for post scaling. It is a pair of + integers, denoting the numerator and denominator of the fraction by + which input signal is multiplied. For example, <1 3> indicates the + signal is scaled down to 1/3 of its value before ADC measurement. If + property is not found default value depending on chip will be used. + items: + - const: 1 + - enum: [ 1, 3, 4, 6, 20, 8, 10 ] + + required: + - reg + - io-channels + + additionalProperties: + false + +required: + - compatible + - reg + - interrupts + - "#address-cells" + - "#size-cells" + - "#thermal-sensor-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/iio/qcom,spmi-vadc.h> + #include <dt-bindings/interrupt-controller/irq.h> + spmi_bus { + #address-cells = <1>; + #size-cells = <0>; + pm8998_adc: adc@3100 { + reg = <0x3100>; + compatible = "qcom,spmi-adc-rev2"; + #address-cells = <1>; + #size-cells = <0>; + #io-channel-cells = <1>; + + /* Other propreties are omitted */ + adc-chan@4c { + reg = <ADC5_XO_THERM_100K_PU>; + }; + }; + + pm8998_adc_tm: adc-tm@3400 { + compatible = "qcom,spmi-adc-tm-hc"; + reg = <0x3400>; + interrupts = <0x2 0x34 0x0 IRQ_TYPE_EDGE_RISING>; + #thermal-sensor-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + thermistor@1 { + reg = <1>; + io-channels = <&pm8998_adc ADC5_XO_THERM_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + }; + }; +... |