diff options
Diffstat (limited to 'Documentation/scsi/aic7xxx.rst')
| -rw-r--r-- | Documentation/scsi/aic7xxx.rst | 458 |
1 files changed, 458 insertions, 0 deletions
diff --git a/Documentation/scsi/aic7xxx.rst b/Documentation/scsi/aic7xxx.rst new file mode 100644 index 000000000..bad0e5567 --- /dev/null +++ b/Documentation/scsi/aic7xxx.rst @@ -0,0 +1,458 @@ +.. SPDX-License-Identifier: GPL-2.0 +.. include:: <isonum.txt> + +======================================================== +Adaptec Aic7xxx Fast -> Ultra160 Family Manager Set v7.0 +======================================================== + +README for The Linux Operating System + +The following information is available in this file: + + 1. Supported Hardware + 2. Version History + 3. Command Line Options + 4. Contacting Adaptec + +1. Supported Hardware +===================== + + The following Adaptec SCSI Chips and Host Adapters are supported by + the aic7xxx driver. + + ======== ===== ========= ======== ========= ===== =============== + Chip MIPS Host Bus MaxSync MaxWidth SCBs Notes + ======== ===== ========= ======== ========= ===== =============== + aic7770 10 EISA/VL 10MHz 16Bit 4 1 + aic7850 10 PCI/32 10MHz 8Bit 3 + aic7855 10 PCI/32 10MHz 8Bit 3 + aic7856 10 PCI/32 10MHz 8Bit 3 + aic7859 10 PCI/32 20MHz 8Bit 3 + aic7860 10 PCI/32 20MHz 8Bit 3 + aic7870 10 PCI/32 10MHz 16Bit 16 + aic7880 10 PCI/32 20MHz 16Bit 16 + aic7890 20 PCI/32 40MHz 16Bit 16 3 4 5 6 7 8 + aic7891 20 PCI/64 40MHz 16Bit 16 3 4 5 6 7 8 + aic7892 20 PCI/64-66 80MHz 16Bit 16 3 4 5 6 7 8 + aic7895 15 PCI/32 20MHz 16Bit 16 2 3 4 5 + aic7895C 15 PCI/32 20MHz 16Bit 16 2 3 4 5 8 + aic7896 20 PCI/32 40MHz 16Bit 16 2 3 4 5 6 7 8 + aic7897 20 PCI/64 40MHz 16Bit 16 2 3 4 5 6 7 8 + aic7899 20 PCI/64-66 80MHz 16Bit 16 2 3 4 5 6 7 8 + ======== ===== ========= ======== ========= ===== =============== + + 1. Multiplexed Twin Channel Device - One controller servicing two + busses. + 2. Multi-function Twin Channel Device - Two controllers on one chip. + 3. Command Channel Secondary DMA Engine - Allows scatter gather list + and SCB prefetch. + 4. 64 Byte SCB Support - Allows disconnected, untagged request table + for all possible target/lun combinations. + 5. Block Move Instruction Support - Doubles the speed of certain + sequencer operations. + 6. 'Bayonet' style Scatter Gather Engine - Improves S/G prefetch + performance. + 7. Queuing Registers - Allows queuing of new transactions without + pausing the sequencer. + 8. Multiple Target IDs - Allows the controller to respond to selection + as a target on multiple SCSI IDs. + + ============== ======= =========== =============== =============== ========= + Controller Chip Host-Bus Int-Connectors Ext-Connectors Notes + ============== ======= =========== =============== =============== ========= + AHA-274X[A] aic7770 EISA SE-50M SE-HD50F + AHA-274X[A]W aic7770 EISA SE-HD68F SE-HD68F + SE-50M + AHA-274X[A]T aic7770 EISA 2 X SE-50M SE-HD50F + AHA-2842 aic7770 VL SE-50M SE-HD50F + AHA-2940AU aic7860 PCI/32 SE-50M SE-HD50F + AVA-2902I aic7860 PCI/32 SE-50M + AVA-2902E aic7860 PCI/32 SE-50M + AVA-2906 aic7856 PCI/32 SE-50M SE-DB25F + APC-7850 aic7850 PCI/32 SE-50M 1 + AVA-2940 aic7860 PCI/32 SE-50M + AHA-2920B aic7860 PCI/32 SE-50M + AHA-2930B aic7860 PCI/32 SE-50M + AHA-2920C aic7856 PCI/32 SE-50M SE-HD50F + AHA-2930C aic7860 PCI/32 SE-50M + AHA-2930C aic7860 PCI/32 SE-50M + AHA-2910C aic7860 PCI/32 SE-50M + AHA-2915C aic7860 PCI/32 SE-50M + AHA-2940AU/CN aic7860 PCI/32 SE-50M SE-HD50F + AHA-2944W aic7870 PCI/32 HVD-HD68F HVD-HD68F + HVD-50M + AHA-3940W aic7870 PCI/32 2 X SE-HD68F SE-HD68F 2 + AHA-2940UW aic7880 PCI/32 SE-HD68F + SE-50M SE-HD68F + AHA-2940U aic7880 PCI/32 SE-50M SE-HD50F + AHA-2940D aic7880 PCI/32 + aHA-2940 A/T aic7880 PCI/32 + AHA-2940D A/T aic7880 PCI/32 + AHA-3940UW aic7880 PCI/32 2 X SE-HD68F SE-HD68F 3 + AHA-3940UWD aic7880 PCI/32 2 X SE-HD68F 2 X SE-VHD68F 3 + AHA-3940U aic7880 PCI/32 2 X SE-50M SE-HD50F 3 + AHA-2944UW aic7880 PCI/32 HVD-HD68F HVD-HD68F + HVD-50M + AHA-3944UWD aic7880 PCI/32 2 X HVD-HD68F 2 X HVD-VHD68F 3 + AHA-4944UW aic7880 PCI/32 + AHA-2930UW aic7880 PCI/32 + AHA-2940UW Pro aic7880 PCI/32 SE-HD68F SE-HD68F 4 + SE-50M + AHA-2940UW/CN aic7880 PCI/32 + AHA-2940UDual aic7895 PCI/32 + AHA-2940UWDual aic7895 PCI/32 + AHA-3940UWD aic7895 PCI/32 + AHA-3940AUW aic7895 PCI/32 + AHA-3940AUWD aic7895 PCI/32 + AHA-3940AU aic7895 PCI/32 + AHA-3944AUWD aic7895 PCI/32 2 X HVD-HD68F 2 X HVD-VHD68F + AHA-2940U2B aic7890 PCI/32 LVD-HD68F LVD-HD68F + AHA-2940U2 OEM aic7891 PCI/64 + AHA-2940U2W aic7890 PCI/32 LVD-HD68F LVD-HD68F + SE-HD68F + SE-50M + AHA-2950U2B aic7891 PCI/64 LVD-HD68F LVD-HD68F + AHA-2930U2 aic7890 PCI/32 LVD-HD68F SE-HD50F + SE-50M + AHA-3950U2B aic7897 PCI/64 + AHA-3950U2D aic7897 PCI/64 + AHA-29160 aic7892 PCI/64-66 + AHA-29160 CPQ aic7892 PCI/64-66 + AHA-29160N aic7892 PCI/32 LVD-HD68F SE-HD50F + SE-50M + AHA-29160LP aic7892 PCI/64-66 + AHA-19160 aic7892 PCI/64-66 + AHA-29150LP aic7892 PCI/64-66 + AHA-29130LP aic7892 PCI/64-66 + AHA-3960D aic7899 PCI/64-66 2 X LVD-HD68F 2 X LVD-VHD68F + LVD-50M + AHA-3960D CPQ aic7899 PCI/64-66 2 X LVD-HD68F 2 X LVD-VHD68F + LVD-50M + AHA-39160 aic7899 PCI/64-66 2 X LVD-HD68F 2 X LVD-VHD68F + LVD-50M + ============== ======= =========== =============== =============== ========= + + 1. No BIOS support + 2. DEC21050 PCI-PCI bridge with multiple controller chips on secondary bus + 3. DEC2115X PCI-PCI bridge with multiple controller chips on secondary bus + 4. All three SCSI connectors may be used simultaneously without + SCSI "stub" effects. + +2. Version History +================== + + * 7.0 (4th August, 2005) + - Updated driver to use SCSI transport class infrastructure + - Upported sequencer and core fixes from last adaptec released + version of the driver. + + * 6.2.36 (June 3rd, 2003) + - Correct code that disables PCI parity error checking. + - Correct and simplify handling of the ignore wide residue + message. The previous code would fail to report a residual + if the transaction data length was even and we received + an IWR message. + - Add support for the 2.5.X EISA framework. + - Update for change in 2.5.X SCSI proc FS interface. + - Correct Domain Validation command-line option parsing. + - When negotiation async via an 8bit WDTR message, send + an SDTR with an offset of 0 to be sure the target + knows we are async. This works around a firmware defect + in the Quantum Atlas 10K. + - Clear PCI error state during driver attach so that we + don't disable memory mapped I/O due to a stray write + by some other driver probe that occurred before we + claimed the controller. + + * 6.2.35 (May 14th, 2003) + - Fix a few GCC 3.3 compiler warnings. + - Correct operation on EISA Twin Channel controller. + - Add support for 2.5.X's scsi_report_device_reset(). + + * 6.2.34 (May 5th, 2003) + - Fix locking regression introduced in 6.2.29 that + could cause a lock order reversal between the io_request_lock + and our per-softc lock. This was only possible on RH9, + SuSE, and kernel.org 2.4.X kernels. + + * 6.2.33 (April 30th, 2003) + - Dynamically disable PCI parity error reporting after + 10 errors are reported to the user. These errors are + the result of some other device issuing PCI transactions + with bad parity. Once the user has been informed of the + problem, continuing to report the errors just degrades + our performance. + + * 6.2.32 (March 28th, 2003) + - Dynamically sized S/G lists to avoid SCSI malloc + pool fragmentation and SCSI mid-layer deadlock. + + * 6.2.28 (January 20th, 2003) + - Domain Validation Fixes + - Add ability to disable PCI parity error checking. + - Enhanced Memory Mapped I/O probe + + * 6.2.20 (November 7th, 2002) + - Added Domain Validation. + +3. Command Line Options +======================= + + + .. Warning:: + + ALTERING OR ADDING THESE DRIVER PARAMETERS + INCORRECTLY CAN RENDER YOUR SYSTEM INOPERABLE. + USE THEM WITH CAUTION. + + Put a .conf file in the /etc/modprobe.d directory and add/edit a + line containing ``options aic7xxx aic7xxx=[command[,command...]]`` where + ``command`` is one or more of the following: + +verbose + + :Definition: enable additional informative messages during driver operation. + :Possible Values: This option is a flag + :Default Value: disabled + + +debug:[value] + + :Definition: Enables various levels of debugging information + :Possible Values: 0x0000 = no debugging, 0xffff = full debugging + :Default Value: 0x0000 + +no_probe + +probe_eisa_vl + + :Definition: Do not probe for EISA/VLB controllers. + This is a toggle. If the driver is compiled + to not probe EISA/VLB controllers by default, + specifying "no_probe" will enable this probing. + If the driver is compiled to probe EISA/VLB + controllers by default, specifying "no_probe" + will disable this probing. + + :Possible Values: This option is a toggle + :Default Value: EISA/VLB probing is disabled by default. + +pci_parity + + :Definition: Toggles the detection of PCI parity errors. + On many motherboards with VIA chipsets, + PCI parity is not generated correctly on the + PCI bus. It is impossible for the hardware to + differentiate between these "spurious" parity + errors and real parity errors. The symptom of + this problem is a stream of the message:: + + "scsi0: Data Parity Error Detected during address or write data phase" + + output by the driver. + + :Possible Values: This option is a toggle + :Default Value: PCI Parity Error reporting is disabled + +no_reset + + :Definition: Do not reset the bus during the initial probe + phase + + :Possible Values: This option is a flag + :Default Value: disabled + +extended + + :Definition: Force extended translation on the controller + :Possible Values: This option is a flag + :Default Value: disabled + +periodic_otag + + :Definition: Send an ordered tag periodically to prevent + tag starvation. Needed for some older devices + + :Possible Values: This option is a flag + :Default Value: disabled + +reverse_scan + + :Definition: Probe the scsi bus in reverse order, starting + with target 15 + + :Possible Values: This option is a flag + :Default Value: disabled + +global_tag_depth:[value] + + :Definition: Global tag depth for all targets on all busses. + This option sets the default tag depth which + may be selectively overridden vi the tag_info + option. + + :Possible Values: 1 - 253 + :Default Value: 32 + +tag_info:{{value[,value...]}[,{value[,value...]}...]} + + :Definition: Set the per-target tagged queue depth on a + per controller basis. Both controllers and targets + may be omitted indicating that they should retain + the default tag depth. + + :Possible Values: 1 - 253 + :Default Value: 32 + + Examples: + + :: + + tag_info:{{16,32,32,64,8,8,,32,32,32,32,32,32,32,32,32} + + On Controller 0: + + - specifies a tag depth of 16 for target 0 + - specifies a tag depth of 64 for target 3 + - specifies a tag depth of 8 for targets 4 and 5 + - leaves target 6 at the default + - specifies a tag depth of 32 for targets 1,2,7-15 + - All other targets retain the default depth. + + :: + + tag_info:{{},{32,,32}} + + On Controller 1: + + - specifies a tag depth of 32 for targets 0 and 2 + - All other targets retain the default depth. + +seltime:[value] + + :Definition: Specifies the selection timeout value + :Possible Values: 0 = 256ms, 1 = 128ms, 2 = 64ms, 3 = 32ms + :Default Value: 0 + +dv: {value[,value...]} + + :Definition: Set Domain Validation Policy on a per-controller basis. + Controllers may be omitted indicating that + they should retain the default read streaming setting. + + :Possible Values: + + ==== =============================== + < 0 Use setting from serial EEPROM. + 0 Disable DV + > 0 Enable DV + ==== =============================== + + + :Default Value: SCSI-Select setting on controllers with a SCSI Select + option for DV. Otherwise, on for controllers supporting + U160 speeds and off for all other controller types. + + Example: + + :: + + dv:{-1,0,,1,1,0} + + - On Controller 0 leave DV at its default setting. + - On Controller 1 disable DV. + - Skip configuration on Controller 2. + - On Controllers 3 and 4 enable DV. + - On Controller 5 disable DV. + +Example:: + + options aic7xxx aic7xxx=verbose,no_probe,tag_info:{{},{,,10}},seltime:1 + +enables verbose logging, Disable EISA/VLB probing, +and set tag depth on Controller 1/Target 2 to 10 tags. + +4. Adaptec Customer Support +=========================== + + A Technical Support Identification (TSID) Number is required for + Adaptec technical support. + + - The 12-digit TSID can be found on the white barcode-type label + included inside the box with your product. The TSID helps us + provide more efficient service by accurately identifying your + product and support status. + + Support Options + - Search the Adaptec Support Knowledgebase (ASK) at + http://ask.adaptec.com for articles, troubleshooting tips, and + frequently asked questions about your product. + - For support via Email, submit your question to Adaptec's + Technical Support Specialists at http://ask.adaptec.com/. + + North America + - Visit our Web site at http://www.adaptec.com/. + - For information about Adaptec's support options, call + 408-957-2550, 24 hours a day, 7 days a week. + - To speak with a Technical Support Specialist, + + * For hardware products, call 408-934-7274, + Monday to Friday, 3:00 am to 5:00 pm, PDT. + * For RAID and Fibre Channel products, call 321-207-2000, + Monday to Friday, 3:00 am to 5:00 pm, PDT. + + To expedite your service, have your computer with you. + - To order Adaptec products, including accessories and cables, + call 408-957-7274. To order cables online go to + http://www.adaptec.com/buy-cables/. + + Europe + - Visit our Web site at http://www.adaptec.com/en-US/_common/world_index. + - To speak with a Technical Support Specialist, call, or email, + + * German: +49 89 4366 5522, Monday-Friday, 9:00-17:00 CET, + http://ask-de.adaptec.com/. + * French: +49 89 4366 5533, Monday-Friday, 9:00-17:00 CET, + http://ask-fr.adaptec.com/. + * English: +49 89 4366 5544, Monday-Friday, 9:00-17:00 GMT, + http://ask.adaptec.com/. + + - You can order Adaptec cables online at + http://www.adaptec.com/buy-cables/. + + Japan + - Visit our web site at http://www.adaptec.co.jp/. + - To speak with a Technical Support Specialist, call + +81 3 5308 6120, Monday-Friday, 9:00 a.m. to 12:00 p.m., + 1:00 p.m. to 6:00 p.m. + +Copyright |copy| 2003 Adaptec Inc. 691 S. Milpitas Blvd., Milpitas CA 95035 USA. + +All rights reserved. + +You are permitted to redistribute, use and modify this README file in whole +or in part in conjunction with redistribution of software governed by the +General Public License, provided that the following conditions are met: + +1. Redistributions of README file must retain the above copyright + notice, this list of conditions, and the following disclaimer, + without modification. +2. The name of the author may not be used to endorse or promote products + derived from this software without specific prior written permission. +3. Modifications or new contributions must be attributed in a copyright + notice identifying the author ("Contributor") and added below the + original copyright notice. The copyright notice is for purposes of + identifying contributors and should not be deemed as permission to alter + the permissions given by Adaptec. + +THIS README FILE IS PROVIDED BY ADAPTEC AND CONTRIBUTORS ``AS IS`` AND +ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY +WARRANTIES OF NON-INFRINGEMENT OR THE IMPLIED WARRANTIES OF MERCHANTABILITY +AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL +ADAPTEC OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, +SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED +TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR +PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF +LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING +NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS README +FILE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. |