diff options
Diffstat (limited to '')
| -rw-r--r-- | arch/arm/boot/dts/intel-ixp42x-linksys-wrv54g.dts | 175 |
1 files changed, 175 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/intel-ixp42x-linksys-wrv54g.dts b/arch/arm/boot/dts/intel-ixp42x-linksys-wrv54g.dts new file mode 100644 index 000000000..5e7e31b74 --- /dev/null +++ b/arch/arm/boot/dts/intel-ixp42x-linksys-wrv54g.dts @@ -0,0 +1,175 @@ +// SPDX-License-Identifier: ISC +/* + * Device Tree file for the Linksys WRV54G router + * Also known as Gemtek GTWX5715 + * Based on a board file by George T. Joseph and other patches. + * This machine is based on IXP425. + */ + +/dts-v1/; + +#include "intel-ixp42x.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Linksys WRV54G / Gemtek GTWX5715"; + compatible = "linksys,wrv54g", "gemtek,gtwx5715", "intel,ixp42x"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 32 MB memory */ + device_type = "memory"; + reg = <0x00000000 0x2000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = "uart1:115200n8"; + }; + + aliases { + /* UART2 is the primary console */ + serial0 = &uart1; + serial1 = &uart0; + }; + + /* There is an unpopulated LED slot (3) connected to GPIO 8 */ + leds { + compatible = "gpio-leds"; + led-power { + label = "wrv54g:yellow:power"; + gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + led-wireless { + label = "wrv54g:yellow:wireless"; + gpios = <&gpio0 9 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + led-internet { + label = "wrv54g:yellow:internet"; + gpios = <&gpio0 1 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + led-dmz { + label = "wrv54g:green:dmz"; + gpios = <&gpio0 4 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + }; + + /* This set-up comes from an OpenWrt patch */ + spi { + compatible = "spi-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + sck-gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>; + miso-gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; + cs-gpios = <&gpio0 5 GPIO_ACTIVE_LOW>; + num-chipselects = <1>; + + switch@0 { + compatible = "micrel,ks8995"; + reg = <0>; + spi-max-frequency = <50000000>; + }; + }; + + soc { + bus@c4000000 { + flash@0,0 { + compatible = "intel,ixp4xx-flash", "cfi-flash"; + bank-width = <2>; + /* Enable writes on the expansion bus */ + intel,ixp4xx-eb-write-enable = <1>; + /* 8 MB of Flash mapped in at CS0 */ + reg = <0 0x00000000 0x00800000>; + + partitions { + compatible = "fixed-partitions"; + /* + * Partition info from a boot log + * CHECKME: not using redboot? FIS index 0x3f @7e00000? + */ + #address-cells = <1>; + #size-cells = <1>; + partition@0 { + label = "boot"; + reg = <0x0 0x140000>; + read-only; + }; + partition@140000 { + label = "linux"; + reg = <0x140000 0x100000>; + read-only; + }; + partition@240000 { + label = "root"; + reg = <0x240000 0x480000>; + read-write; + }; + }; + }; + }; + + pci@c0000000 { + status = "ok"; + + /* + * We have up to 2 slots (IDSEL) with 2 swizzled IRQs. + * Derived from the GTWX5715 PCI boardfile. + */ + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + /* IDSEL 0 */ + <0x0000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 0 is irq 10 */ + <0x0000 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 0 is irq 11 */ + /* IDSEL 1 */ + <0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */ + <0x0800 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>; /* INT B on slot 1 is irq 10 */ + }; + + /* + * EthB - connected to the KS8995 switch ports 1-4 + * FIXME: the boardfile defines .phy_mask = 0x1e for this port to enable output to + * all four switch ports, also using an out of tree multiphy patch. + * Do we need a new binding and property for this? + */ + ethernet@c8009000 { + status = "ok"; + queue-rx = <&qmgr 3>; + queue-txready = <&qmgr 20>; + phy-mode = "rgmii"; + phy-handle = <&phy4>; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + /* Should be ports 1-4 on the KS8995 switch */ + phy4: ethernet-phy@4 { + reg = <4>; + }; + + /* Should be port 5 on the KS8995 switch */ + phy5: ethernet-phy@5 { + reg = <5>; + }; + }; + }; + + /* EthC - connected to KS8995 switch port 5 */ + ethernet@c800a000 { + status = "ok"; + queue-rx = <&qmgr 4>; + queue-txready = <&qmgr 21>; + phy-mode = "rgmii"; + phy-handle = <&phy5>; + }; + }; +}; |