diff options
Diffstat (limited to 'arch/arm/mach-ux500/cpu-db8500.c')
| -rw-r--r-- | arch/arm/mach-ux500/cpu-db8500.c | 139 |
1 files changed, 139 insertions, 0 deletions
diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c new file mode 100644 index 000000000..e929aaa74 --- /dev/null +++ b/arch/arm/mach-ux500/cpu-db8500.c @@ -0,0 +1,139 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2008-2009 ST-Ericsson SA + * + * Author: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com> + */ +#include <linux/types.h> +#include <linux/init.h> +#include <linux/device.h> +#include <linux/amba/bus.h> +#include <linux/interrupt.h> +#include <linux/irq.h> +#include <linux/irqchip.h> +#include <linux/irqchip/arm-gic.h> +#include <linux/mfd/dbx500-prcmu.h> +#include <linux/platform_data/arm-ux500-pm.h> +#include <linux/platform_device.h> +#include <linux/io.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_platform.h> +#include <linux/regulator/machine.h> + +#include <asm/outercache.h> +#include <asm/hardware/cache-l2x0.h> +#include <asm/mach/map.h> +#include <asm/mach/arch.h> + +#include "db8500-regs.h" +#include "pm_domains.h" + +static int __init ux500_l2x0_unlock(void) +{ + int i; + struct device_node *np; + void __iomem *l2x0_base; + + np = of_find_compatible_node(NULL, NULL, "arm,pl310-cache"); + l2x0_base = of_iomap(np, 0); + of_node_put(np); + if (!l2x0_base) + return -ENODEV; + + /* + * Unlock Data and Instruction Lock if locked. Ux500 U-Boot versions + * apparently locks both caches before jumping to the kernel. The + * l2x0 core will not touch the unlock registers if the l2x0 is + * already enabled, so we do it right here instead. The PL310 has + * 8 sets of registers, one per possible CPU. + */ + for (i = 0; i < 8; i++) { + writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_D_BASE + + i * L2X0_LOCKDOWN_STRIDE); + writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_I_BASE + + i * L2X0_LOCKDOWN_STRIDE); + } + iounmap(l2x0_base); + return 0; +} + +static void ux500_l2c310_write_sec(unsigned long val, unsigned reg) +{ + /* + * We can't write to secure registers as we are in non-secure + * mode, until we have some SMI service available. + */ +} + +/* + * FIXME: Should we set up the GPIO domain here? + * + * The problem is that we cannot put the interrupt resources into the platform + * device until the irqdomain has been added. Right now, we set the GIC interrupt + * domain from init_irq(), then load the gpio driver from + * core_initcall(nmk_gpio_init) and add the platform devices from + * arch_initcall(customize_machine). + * + * This feels fragile because it depends on the gpio device getting probed + * _before_ any device uses the gpio interrupts. +*/ +static void __init ux500_init_irq(void) +{ + struct device_node *np; + struct resource r; + + irqchip_init(); + prcmu_early_init(); + np = of_find_compatible_node(NULL, NULL, "stericsson,db8500-prcmu"); + of_address_to_resource(np, 0, &r); + of_node_put(np); + if (!r.start) { + pr_err("could not find PRCMU base resource\n"); + return; + } + ux500_pm_init(r.start, r.end-r.start); + + /* Unlock before init */ + ux500_l2x0_unlock(); + outer_cache.write_sec = ux500_l2c310_write_sec; +} + +static void ux500_restart(enum reboot_mode mode, const char *cmd) +{ + local_irq_disable(); + local_fiq_disable(); + + prcmu_system_reset(0); +} + +static const struct of_device_id u8500_local_bus_nodes[] = { + /* only create devices below soc node */ + { .compatible = "stericsson,db8500", }, + { .compatible = "simple-bus"}, + { }, +}; + +static void __init u8500_init_machine(void) +{ + /* Initialize ux500 power domains */ + ux500_pm_domains_init(); + + of_platform_populate(NULL, u8500_local_bus_nodes, + NULL, NULL); +} + +static const char * stericsson_dt_platform_compat[] = { + "st-ericsson,u8500", + "st-ericsson,u9500", + NULL, +}; + +DT_MACHINE_START(U8500_DT, "ST-Ericsson Ux5x0 platform (Device Tree Support)") + .l2c_aux_val = 0, + .l2c_aux_mask = ~0, + .init_irq = ux500_init_irq, + .init_machine = u8500_init_machine, + .dt_compat = stericsson_dt_platform_compat, + .restart = ux500_restart, +MACHINE_END |