1 files changed, 146 insertions, 0 deletions
diff --git a/arch/arm64/boot/dts/qcom/pm8150.dtsi b/arch/arm64/boot/dts/qcom/pm8150.dtsi
new file mode 100644
index 000000000..574fa95a2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm8150.dtsi
@@ -0,0 +1,146 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2019, Linaro Limited
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+
+/ {
+	thermal-zones {
+		pm8150-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm8150_temp>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+
+				trip2 {
+					temperature = <145000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pm8150_0: pmic@0 {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pon: pon@800 {
+			compatible = "qcom,pm8998-pon";
+			reg = <0x0800>;
+			mode-bootloader = <0x2>;
+			mode-recovery = <0x1>;
+
+			pon_pwrkey: pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_POWER>;
+
+				status = "disabled";
+			};
+
+			pon_resin: resin {
+				compatible = "qcom,pm8941-resin";
+				interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+
+				status = "disabled";
+			};
+		};
+
+		pm8150_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			io-channels = <&pm8150_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm8150_adc: adc@3100 {
+			compatible = "qcom,spmi-adc5";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+			ref-gnd@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			vref-1p25@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
+			die-temp@6 {
+				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "die_temp";
+			};
+		};
+
+		pm8150_adc_tm: adc-tm@3500 {
+			compatible = "qcom,spmi-adc-tm5";
+			reg = <0x3500>;
+			interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
+		};
+
+		pm8150_gpios: gpio@c000 {
+			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pm8150_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmic@1 {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};