summaryrefslogtreecommitdiffstats
path: root/arch/powerpc/boot/dts/turris1x.dts
diff options
context:
space:
mode:
Diffstat (limited to '')
-rw-r--r--arch/powerpc/boot/dts/turris1x.dts497
1 files changed, 497 insertions, 0 deletions
diff --git a/arch/powerpc/boot/dts/turris1x.dts b/arch/powerpc/boot/dts/turris1x.dts
new file mode 100644
index 000000000..9377055d5
--- /dev/null
+++ b/arch/powerpc/boot/dts/turris1x.dts
@@ -0,0 +1,497 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Turris 1.x Device Tree Source
+ *
+ * Copyright 2013 - 2022 CZ.NIC z.s.p.o. (http://www.nic.cz/)
+ *
+ * Pinout, Schematics and Altium hardware design files are open source
+ * and available at: https://docs.turris.cz/hw/turris-1x/turris-1x/
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+/include/ "fsl/p2020si-pre.dtsi"
+
+/ {
+ model = "Turris 1.x";
+ compatible = "cznic,turris1x", "fsl,P2020RDB-PC"; /* fsl,P2020RDB-PC is required for booting Linux */
+
+ aliases {
+ ethernet0 = &enet0;
+ ethernet1 = &enet1;
+ ethernet2 = &enet2;
+ serial0 = &serial0;
+ serial1 = &serial1;
+ pci0 = &pci0;
+ pci1 = &pci1;
+ pci2 = &pci2;
+ spi0 = &spi0;
+ };
+
+ memory {
+ device_type = "memory";
+ };
+
+ soc: soc@ffe00000 {
+ ranges = <0x0 0x0 0xffe00000 0x00100000>;
+
+ i2c@3000 {
+ /* PCA9557PW GPIO controller for boot config */
+ gpio-controller@18 {
+ compatible = "nxp,pca9557";
+ label = "bootcfg";
+ reg = <0x18>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ polarity = <0x00>;
+ };
+
+ /* STM32F030R8T6 MCU for power control */
+ power-control@2a {
+ /*
+ * Turris Power Control firmware runs on STM32F0 MCU.
+ * This firmware is open source and available at:
+ * https://gitlab.nic.cz/turris/hw/turris_power_control
+ */
+ reg = <0x2a>;
+ };
+
+ /* DDR3 SPD/EEPROM PSWP instruction */
+ eeprom@32 {
+ reg = <0x32>;
+ };
+
+ /* SA56004ED temperature control */
+ temperature-sensor@4c {
+ compatible = "nxp,sa56004";
+ reg = <0x4c>;
+ interrupt-parent = <&gpio>;
+ interrupts = <12 IRQ_TYPE_LEVEL_LOW>, /* GPIO12 - ALERT pin */
+ <13 IRQ_TYPE_LEVEL_LOW>; /* GPIO13 - CRIT pin */
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Local temperature sensor (SA56004ED internal) */
+ channel@0 {
+ reg = <0>;
+ label = "board";
+ };
+
+ /* Remote temperature sensor (D+/D- connected to P2020 CPU Temperature Diode) */
+ channel@1 {
+ reg = <1>;
+ label = "cpu";
+ };
+ };
+
+ /* DDR3 SPD/EEPROM */
+ eeprom@52 {
+ compatible = "atmel,spd";
+ reg = <0x52>;
+ };
+
+ /* MCP79402-I/ST Protected EEPROM */
+ eeprom@57 {
+ reg = <0x57>;
+ };
+
+ /* ATSHA204-TH-DA-T crypto module */
+ crypto@64 {
+ compatible = "atmel,atsha204";
+ reg = <0x64>;
+ };
+
+ /* IDT6V49205BNLGI clock generator */
+ clock-generator@69 {
+ compatible = "idt,6v49205b";
+ reg = <0x69>;
+ };
+
+ /* MCP79402-I/ST RTC */
+ rtc@6f {
+ compatible = "microchip,mcp7940x";
+ reg = <0x6f>;
+ interrupt-parent = <&gpio>;
+ interrupts = <14 0>; /* GPIO14 - MFP pin */
+ };
+ };
+
+ /* SPI on connector P1 */
+ spi0: spi@7000 {
+ };
+
+ gpio: gpio-controller@fc00 {
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ };
+
+ /* Connected to SMSC USB2412-DZK 2-Port USB 2.0 Hub Controller */
+ usb@22000 {
+ phy_type = "ulpi";
+ dr_mode = "host";
+ };
+
+ enet0: ethernet@24000 {
+ /* Connected to port 6 of QCA8337N-AL3C switch */
+ phy-connection-type = "rgmii-id";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ mdio@24520 {
+ /* KSZ9031RNXCA ethernet phy for WAN port */
+ phy: ethernet-phy@7 {
+ interrupts = <3 1 0 0>;
+ reg = <0x7>;
+ };
+
+ /* QCA8337N-AL3C switch with integrated ethernet PHYs for LAN ports */
+ switch@10 {
+ compatible = "qca,qca8337";
+ interrupts = <2 1 0 0>;
+ reg = <0x10>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "cpu";
+ ethernet = <&enet1>;
+ phy-mode = "rgmii-id";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan5";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan4";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan2";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "lan1";
+ };
+
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&enet0>;
+ phy-mode = "rgmii-id";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
+
+ ptp_clock@24e00 {
+ fsl,tclk-period = <5>;
+ fsl,tmr-prsc = <200>;
+ fsl,tmr-add = <0xcccccccd>;
+ fsl,tmr-fiper1 = <0x3b9ac9fb>;
+ fsl,tmr-fiper2 = <0x0001869b>;
+ fsl,max-adj = <249999999>;
+ };
+
+ enet1: ethernet@25000 {
+ /* Connected to port 0 of QCA8337N-AL3C switch */
+ phy-connection-type = "rgmii-id";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ mdio@25520 {
+ status = "disabled";
+ };
+
+ enet2: ethernet@26000 {
+ /* Connected to KSZ9031RNXCA ethernet phy (WAN port) */
+ label = "wan";
+ phy-handle = <&phy>;
+ phy-connection-type = "rgmii-id";
+ };
+
+ mdio@26520 {
+ status = "disabled";
+ };
+
+ sdhc@2e000 {
+ bus-width = <4>;
+ cd-gpios = <&gpio 8 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ lbc: localbus@ffe05000 {
+ reg = <0 0xffe05000 0 0x1000>;
+
+ ranges = <0x0 0x0 0x0 0xef000000 0x01000000>, /* NOR */
+ <0x1 0x0 0x0 0xff800000 0x00040000>, /* NAND */
+ <0x3 0x0 0x0 0xffa00000 0x00020000>; /* CPLD */
+
+ /* S29GL128P90TFIR10 NOR */
+ nor@0,0 {
+ compatible = "cfi-flash";
+ reg = <0x0 0x0 0x01000000>;
+ bank-width = <2>;
+ device-width = <1>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ /* 128 kB for Device Tree Blob */
+ reg = <0x00000000 0x00020000>;
+ label = "dtb";
+ };
+
+ partition@20000 {
+ /* 1.7 MB for Linux Kernel Image */
+ reg = <0x00020000 0x001a0000>;
+ label = "kernel";
+ };
+
+ partition@1c0000 {
+ /* 1.5 MB for Rescue JFFS2 Root File System */
+ reg = <0x001c0000 0x00180000>;
+ label = "rescue";
+ };
+
+ partition@340000 {
+ /* 11 MB for TAR.XZ Archive with Factory content of NAND Root File System */
+ reg = <0x00340000 0x00b00000>;
+ label = "factory";
+ };
+
+ partition@e40000 {
+ /* 768 kB for Certificates JFFS2 File System */
+ reg = <0x00e40000 0x000c0000>;
+ label = "certificates";
+ };
+
+ /* free unused space 0x00f00000-0x00f20000 */
+
+ partition@f20000 {
+ /* 128 kB for U-Boot Environment Variables */
+ reg = <0x00f20000 0x00020000>;
+ label = "u-boot-env";
+ };
+
+ partition@f40000 {
+ /* 768 kB for U-Boot Bootloader Image */
+ reg = <0x00f40000 0x000c0000>;
+ label = "u-boot";
+ };
+ };
+ };
+
+ /* MT29F2G08ABAEAWP:E NAND */
+ nand@1,0 {
+ compatible = "fsl,p2020-fcm-nand", "fsl,elbc-fcm-nand";
+ reg = <0x1 0x0 0x00040000>;
+ nand-ecc-mode = "soft";
+ nand-ecc-algo = "bch";
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ /* 256 MB for UBI with one volume: UBIFS Root File System */
+ reg = <0x00000000 0x10000000>;
+ label = "rootfs";
+ };
+ };
+ };
+
+ /* LCMXO1200C-3FTN256C FPGA */
+ cpld@3,0 {
+ /*
+ * Turris CPLD firmware which runs on this Lattice FPGA,
+ * is extended version of P1021RDB-PC CPLD v4.1 firmware.
+ * It is backward compatible with its original version
+ * and the only extension is support for Turris LEDs.
+ * Turris CPLD firmware is open source and available at:
+ * https://gitlab.nic.cz/turris/hw/turris_cpld/-/blob/master/CZ_NIC_Router_CPLD.v
+ */
+ compatible = "cznic,turris1x-cpld", "fsl,p1021rdb-pc-cpld", "simple-bus", "syscon";
+ reg = <0x3 0x0 0x30>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x0 0x3 0x0 0x00020000>;
+
+ /* MAX6370KA+T watchdog */
+ watchdog@2 {
+ /*
+ * CPLD firmware maps SET0, SET1 and SET2
+ * input logic of MAX6370KA+T chip to CPLD
+ * memory space at byte offset 0x2. WDI
+ * input logic is outside of the CPLD and
+ * connected via external GPIO.
+ */
+ compatible = "maxim,max6370";
+ reg = <0x02 0x01>;
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ };
+
+ reboot@d {
+ compatible = "syscon-reboot";
+ reg = <0x0d 0x01>;
+ offset = <0x0d>;
+ mask = <0x01>;
+ value = <0x01>;
+ };
+
+ led-controller@13 {
+ /*
+ * LEDs are controlled by CPLD firmware.
+ * All five LAN LEDs share common RGB settings
+ * and so it is not possible to set different
+ * colors on different LAN ports.
+ */
+ compatible = "cznic,turris1x-leds";
+ reg = <0x13 0x1d>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ multi-led@0 {
+ reg = <0x0>;
+ color = <LED_COLOR_ID_RGB>;
+ function = LED_FUNCTION_WAN;
+ };
+
+ multi-led@1 {
+ reg = <0x1>;
+ color = <LED_COLOR_ID_RGB>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <5>;
+ };
+
+ multi-led@2 {
+ reg = <0x2>;
+ color = <LED_COLOR_ID_RGB>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <4>;
+ };
+
+ multi-led@3 {
+ reg = <0x3>;
+ color = <LED_COLOR_ID_RGB>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <3>;
+ };
+
+ multi-led@4 {
+ reg = <0x4>;
+ color = <LED_COLOR_ID_RGB>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <2>;
+ };
+
+ multi-led@5 {
+ reg = <0x5>;
+ color = <LED_COLOR_ID_RGB>;
+ function = LED_FUNCTION_LAN;
+ function-enumerator = <1>;
+ };
+
+ multi-led@6 {
+ reg = <0x6>;
+ color = <LED_COLOR_ID_RGB>;
+ function = LED_FUNCTION_WLAN;
+ };
+
+ multi-led@7 {
+ reg = <0x7>;
+ color = <LED_COLOR_ID_RGB>;
+ function = LED_FUNCTION_POWER;
+ };
+ };
+ };
+ };
+
+ pci2: pcie@ffe08000 {
+ /*
+ * PCIe bus for on-board TUSB7340RKM USB 3.0 xHCI controller.
+ * This xHCI controller is available only on Turris 1.1 boards.
+ * Turris 1.0 boards have nothing connected to this PCIe bus,
+ * so system would see only PCIe Root Port of this PCIe Root
+ * Complex. TUSB7340RKM xHCI controller has four SuperSpeed
+ * channels. Channel 0 is connected to the front USB 3.0 port,
+ * channel 1 (but only USB 2.0 subset) to USB 2.0 pins on mPCIe
+ * slot 1 (CN5), channels 2 and 3 to connector P600.
+ *
+ * P2020 PCIe Root Port does not use PCIe MEM and xHCI controller
+ * uses 64kB + 8kB of PCIe MEM. No PCIe IO is used or required.
+ * So allocate 128kB of PCIe MEM for this PCIe bus.
+ */
+ reg = <0 0xffe08000 0 0x1000>;
+ ranges = <0x02000000 0x0 0xc0000000 0 0xc0000000 0x0 0x00020000>, /* MEM */
+ <0x01000000 0x0 0x00000000 0 0xffc20000 0x0 0x00010000>; /* IO */
+
+ pcie@0 {
+ ranges;
+ };
+ };
+
+ pci1: pcie@ffe09000 {
+ /* PCIe bus on mPCIe slot 2 (CN6) for expansion mPCIe card */
+ reg = <0 0xffe09000 0 0x1000>;
+ ranges = <0x02000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000>, /* MEM */
+ <0x01000000 0x0 0x00000000 0 0xffc10000 0x0 0x00010000>; /* IO */
+
+ pcie@0 {
+ ranges;
+ };
+ };
+
+ pci0: pcie@ffe0a000 {
+ /*
+ * PCIe bus on mPCIe slot 1 (CN5) for expansion mPCIe card.
+ * Turris 1.1 boards have in this mPCIe slot additional USB 2.0
+ * pins via channel 1 of TUSB7340RKM xHCI controller and also
+ * additional SIM card slot, both for USB-based WWAN cards.
+ */
+ reg = <0 0xffe0a000 0 0x1000>;
+ ranges = <0x02000000 0x0 0x80000000 0 0x80000000 0x0 0x20000000>, /* MEM */
+ <0x01000000 0x0 0x00000000 0 0xffc00000 0x0 0x00010000>; /* IO */
+
+ pcie@0 {
+ ranges;
+ };
+ };
+};
+
+/include/ "fsl/p2020si-post.dtsi"
generated by cgit v1.2.3 (git 2.39.1) at 2024-12-02 08:44:09 +0000