summaryrefslogtreecommitdiffstats
path: root/drivers/ata/pata_sc1200.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/ata/pata_sc1200.c')
-rw-r--r--drivers/ata/pata_sc1200.c257
1 files changed, 257 insertions, 0 deletions
diff --git a/drivers/ata/pata_sc1200.c b/drivers/ata/pata_sc1200.c
new file mode 100644
index 000000000..f28daf62a
--- /dev/null
+++ b/drivers/ata/pata_sc1200.c
@@ -0,0 +1,257 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * New ATA layer SC1200 driver Alan Cox <alan@lxorguk.ukuu.org.uk>
+ *
+ * TODO: Mode selection filtering
+ * TODO: Needs custom DMA cleanup code
+ *
+ * Based very heavily on
+ *
+ * linux/drivers/ide/pci/sc1200.c Version 0.91 28-Jan-2003
+ *
+ * Copyright (C) 2000-2002 Mark Lord <mlord@pobox.com>
+ * May be copied or modified under the terms of the GNU General Public License
+ *
+ * Development of this chipset driver was funded
+ * by the nice folks at National Semiconductor.
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pci.h>
+#include <linux/blkdev.h>
+#include <linux/delay.h>
+#include <scsi/scsi_host.h>
+#include <linux/libata.h>
+
+#define DRV_NAME "pata_sc1200"
+#define DRV_VERSION "0.2.6"
+
+#define SC1200_REV_A 0x00
+#define SC1200_REV_B1 0x01
+#define SC1200_REV_B3 0x02
+#define SC1200_REV_C1 0x03
+#define SC1200_REV_D1 0x04
+
+/**
+ * sc1200_clock - PCI clock
+ *
+ * Return the PCI bus clocking for the SC1200 chipset configuration
+ * in use. We return 0 for 33MHz 1 for 48MHz and 2 for 66Mhz
+ */
+
+static int sc1200_clock(void)
+{
+ /* Magic registers that give us the chipset data */
+ u8 chip_id = inb(0x903C);
+ u8 silicon_rev = inb(0x903D);
+ u16 pci_clock;
+
+ if (chip_id == 0x04 && silicon_rev < SC1200_REV_B1)
+ return 0; /* 33 MHz mode */
+
+ /* Clock generator configuration 0x901E its 8/9 are the PCI clocking
+ 0/3 is 33Mhz 1 is 48 2 is 66 */
+
+ pci_clock = inw(0x901E);
+ pci_clock >>= 8;
+ pci_clock &= 0x03;
+ if (pci_clock == 3)
+ pci_clock = 0;
+ return pci_clock;
+}
+
+/**
+ * sc1200_set_piomode - PIO setup
+ * @ap: ATA interface
+ * @adev: device on the interface
+ *
+ * Set our PIO requirements. This is fairly simple on the SC1200
+ */
+
+static void sc1200_set_piomode(struct ata_port *ap, struct ata_device *adev)
+{
+ static const u32 pio_timings[4][5] = {
+ /* format0, 33Mhz */
+ { 0x00009172, 0x00012171, 0x00020080, 0x00032010, 0x00040010 },
+ /* format1, 33Mhz */
+ { 0xd1329172, 0x71212171, 0x30200080, 0x20102010, 0x00100010 },
+ /* format1, 48Mhz */
+ { 0xfaa3f4f3, 0xc23232b2, 0x513101c1, 0x31213121, 0x10211021 },
+ /* format1, 66Mhz */
+ { 0xfff4fff4, 0xf35353d3, 0x814102f1, 0x42314231, 0x11311131 }
+ };
+
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ u32 format;
+ unsigned int reg = 0x40 + 0x10 * ap->port_no;
+ int mode = adev->pio_mode - XFER_PIO_0;
+
+ pci_read_config_dword(pdev, reg + 4, &format);
+ format >>= 31;
+ format += sc1200_clock();
+ pci_write_config_dword(pdev, reg + 8 * adev->devno,
+ pio_timings[format][mode]);
+}
+
+/**
+ * sc1200_set_dmamode - DMA timing setup
+ * @ap: ATA interface
+ * @adev: Device being configured
+ *
+ * We cannot mix MWDMA and UDMA without reloading timings each switch
+ * master to slave.
+ */
+
+static void sc1200_set_dmamode(struct ata_port *ap, struct ata_device *adev)
+{
+ static const u32 udma_timing[3][3] = {
+ { 0x00921250, 0x00911140, 0x00911030 },
+ { 0x00932470, 0x00922260, 0x00922140 },
+ { 0x009436A1, 0x00933481, 0x00923261 }
+ };
+
+ static const u32 mwdma_timing[3][3] = {
+ { 0x00077771, 0x00012121, 0x00002020 },
+ { 0x000BBBB2, 0x00024241, 0x00013131 },
+ { 0x000FFFF3, 0x00035352, 0x00015151 }
+ };
+
+ int clock = sc1200_clock();
+ struct pci_dev *pdev = to_pci_dev(ap->host->dev);
+ unsigned int reg = 0x40 + 0x10 * ap->port_no;
+ int mode = adev->dma_mode;
+ u32 format;
+
+ if (mode >= XFER_UDMA_0)
+ format = udma_timing[clock][mode - XFER_UDMA_0];
+ else
+ format = mwdma_timing[clock][mode - XFER_MW_DMA_0];
+
+ if (adev->devno == 0) {
+ u32 timings;
+
+ pci_read_config_dword(pdev, reg + 4, &timings);
+ timings &= 0x80000000UL;
+ timings |= format;
+ pci_write_config_dword(pdev, reg + 4, timings);
+ } else
+ pci_write_config_dword(pdev, reg + 12, format);
+}
+
+/**
+ * sc1200_qc_issue - command issue
+ * @qc: command pending
+ *
+ * Called when the libata layer is about to issue a command. We wrap
+ * this interface so that we can load the correct ATA timings if
+ * necessary. Specifically we have a problem that there is only
+ * one MWDMA/UDMA bit.
+ */
+
+static unsigned int sc1200_qc_issue(struct ata_queued_cmd *qc)
+{
+ struct ata_port *ap = qc->ap;
+ struct ata_device *adev = qc->dev;
+ struct ata_device *prev = ap->private_data;
+
+ /* See if the DMA settings could be wrong */
+ if (ata_dma_enabled(adev) && adev != prev && prev != NULL) {
+ /* Maybe, but do the channels match MWDMA/UDMA ? */
+ if ((ata_using_udma(adev) && !ata_using_udma(prev)) ||
+ (ata_using_udma(prev) && !ata_using_udma(adev)))
+ /* Switch the mode bits */
+ sc1200_set_dmamode(ap, adev);
+ }
+
+ return ata_bmdma_qc_issue(qc);
+}
+
+/**
+ * sc1200_qc_defer - implement serialization
+ * @qc: command
+ *
+ * Serialize command issue on this controller.
+ */
+
+static int sc1200_qc_defer(struct ata_queued_cmd *qc)
+{
+ struct ata_host *host = qc->ap->host;
+ struct ata_port *alt = host->ports[1 ^ qc->ap->port_no];
+ int rc;
+
+ /* First apply the usual rules */
+ rc = ata_std_qc_defer(qc);
+ if (rc != 0)
+ return rc;
+
+ /* Now apply serialization rules. Only allow a command if the
+ other channel state machine is idle */
+ if (alt && alt->qc_active)
+ return ATA_DEFER_PORT;
+ return 0;
+}
+
+static struct scsi_host_template sc1200_sht = {
+ ATA_BASE_SHT(DRV_NAME),
+ .sg_tablesize = LIBATA_DUMB_MAX_PRD,
+ .dma_boundary = ATA_DMA_BOUNDARY,
+};
+
+static struct ata_port_operations sc1200_port_ops = {
+ .inherits = &ata_bmdma_port_ops,
+ .qc_prep = ata_bmdma_dumb_qc_prep,
+ .qc_issue = sc1200_qc_issue,
+ .qc_defer = sc1200_qc_defer,
+ .cable_detect = ata_cable_40wire,
+ .set_piomode = sc1200_set_piomode,
+ .set_dmamode = sc1200_set_dmamode,
+};
+
+/**
+ * sc1200_init_one - Initialise an SC1200
+ * @dev: PCI device
+ * @id: Entry in match table
+ *
+ * Just throw the needed data at the libata helper and it does all
+ * our work.
+ */
+
+static int sc1200_init_one(struct pci_dev *dev, const struct pci_device_id *id)
+{
+ static const struct ata_port_info info = {
+ .flags = ATA_FLAG_SLAVE_POSS,
+ .pio_mask = ATA_PIO4,
+ .mwdma_mask = ATA_MWDMA2,
+ .udma_mask = ATA_UDMA2,
+ .port_ops = &sc1200_port_ops
+ };
+ const struct ata_port_info *ppi[] = { &info, NULL };
+
+ return ata_pci_bmdma_init_one(dev, ppi, &sc1200_sht, NULL, 0);
+}
+
+static const struct pci_device_id sc1200[] = {
+ { PCI_VDEVICE(NS, PCI_DEVICE_ID_NS_SCx200_IDE), },
+
+ { },
+};
+
+static struct pci_driver sc1200_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = sc1200,
+ .probe = sc1200_init_one,
+ .remove = ata_pci_remove_one,
+#ifdef CONFIG_PM_SLEEP
+ .suspend = ata_pci_device_suspend,
+ .resume = ata_pci_device_resume,
+#endif
+};
+
+module_pci_driver(sc1200_pci_driver);
+
+MODULE_AUTHOR("Alan Cox, Mark Lord");
+MODULE_DESCRIPTION("low-level driver for the NS/AMD SC1200");
+MODULE_LICENSE("GPL");
+MODULE_DEVICE_TABLE(pci, sc1200);
+MODULE_VERSION(DRV_VERSION);