diff options
Diffstat (limited to 'drivers/ata/pata_via.c')
| -rw-r--r-- | drivers/ata/pata_via.c | 708 |
1 files changed, 708 insertions, 0 deletions
diff --git a/drivers/ata/pata_via.c b/drivers/ata/pata_via.c new file mode 100644 index 000000000..34f00f389 --- /dev/null +++ b/drivers/ata/pata_via.c @@ -0,0 +1,708 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * pata_via.c - VIA PATA for new ATA layer + * (C) 2005-2006 Red Hat Inc + * + * Documentation + * Most chipset documentation available under NDA only + * + * VIA version guide + * VIA VT82C561 - early design, uses ata_generic currently + * VIA VT82C576 - MWDMA, 33Mhz + * VIA VT82C586 - MWDMA, 33Mhz + * VIA VT82C586a - Added UDMA to 33Mhz + * VIA VT82C586b - UDMA33 + * VIA VT82C596a - Nonfunctional UDMA66 + * VIA VT82C596b - Working UDMA66 + * VIA VT82C686 - Nonfunctional UDMA66 + * VIA VT82C686a - Working UDMA66 + * VIA VT82C686b - Updated to UDMA100 + * VIA VT8231 - UDMA100 + * VIA VT8233 - UDMA100 + * VIA VT8233a - UDMA133 + * VIA VT8233c - UDMA100 + * VIA VT8235 - UDMA133 + * VIA VT8237 - UDMA133 + * VIA VT8237A - UDMA133 + * VIA VT8237S - UDMA133 + * VIA VT8251 - UDMA133 + * + * Most registers remain compatible across chips. Others start reserved + * and acquire sensible semantics if set to 1 (eg cable detect). A few + * exceptions exist, notably around the FIFO settings. + * + * One additional quirk of the VIA design is that like ALi they use few + * PCI IDs for a lot of chips. + * + * Based heavily on: + * + * Version 3.38 + * + * VIA IDE driver for Linux. Supported southbridges: + * + * vt82c576, vt82c586, vt82c586a, vt82c586b, vt82c596a, vt82c596b, + * vt82c686, vt82c686a, vt82c686b, vt8231, vt8233, vt8233c, vt8233a, + * vt8235, vt8237 + * + * Copyright (c) 2000-2002 Vojtech Pavlik + * + * Based on the work of: + * Michel Aubry + * Jeff Garzik + * Andre Hedrick + + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/gfp.h> +#include <scsi/scsi_host.h> +#include <linux/libata.h> +#include <linux/dmi.h> + +#define DRV_NAME "pata_via" +#define DRV_VERSION "0.3.4" + +enum { + VIA_BAD_PREQ = 0x01, /* Crashes if PREQ# till DDACK# set */ + VIA_BAD_CLK66 = 0x02, /* 66 MHz clock doesn't work correctly */ + VIA_SET_FIFO = 0x04, /* Needs to have FIFO split set */ + VIA_NO_UNMASK = 0x08, /* Doesn't work with IRQ unmasking on */ + VIA_BAD_ID = 0x10, /* Has wrong vendor ID (0x1107) */ + VIA_BAD_AST = 0x20, /* Don't touch Address Setup Timing */ + VIA_NO_ENABLES = 0x40, /* Has no enablebits */ + VIA_SATA_PATA = 0x80, /* SATA/PATA combined configuration */ +}; + +enum { + VIA_IDFLAG_SINGLE = (1 << 0), /* single channel controller) */ +}; + +/* + * VIA SouthBridge chips. + */ + +static const struct via_isa_bridge { + const char *name; + u16 id; + u8 rev_min; + u8 rev_max; + u8 udma_mask; + u8 flags; +} via_isa_bridges[] = { + { "vx855", PCI_DEVICE_ID_VIA_VX855, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA }, + { "vx800", PCI_DEVICE_ID_VIA_VX800, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA }, + { "vt8261", PCI_DEVICE_ID_VIA_8261, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST }, + { "vt8237s", PCI_DEVICE_ID_VIA_8237S, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST }, + { "vt8251", PCI_DEVICE_ID_VIA_8251, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST }, + { "cx700", PCI_DEVICE_ID_VIA_CX700, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA }, + { "vt6410", PCI_DEVICE_ID_VIA_6410, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_NO_ENABLES }, + { "vt6415", PCI_DEVICE_ID_VIA_6415, 0x00, 0xff, ATA_UDMA6, VIA_BAD_AST | VIA_NO_ENABLES }, + { "vt8237a", PCI_DEVICE_ID_VIA_8237A, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST }, + { "vt8237", PCI_DEVICE_ID_VIA_8237, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST }, + { "vt8235", PCI_DEVICE_ID_VIA_8235, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST }, + { "vt8233a", PCI_DEVICE_ID_VIA_8233A, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST }, + { "vt8233c", PCI_DEVICE_ID_VIA_8233C_0, 0x00, 0x2f, ATA_UDMA5, }, + { "vt8233", PCI_DEVICE_ID_VIA_8233_0, 0x00, 0x2f, ATA_UDMA5, }, + { "vt8231", PCI_DEVICE_ID_VIA_8231, 0x00, 0x2f, ATA_UDMA5, }, + { "vt82c686b", PCI_DEVICE_ID_VIA_82C686, 0x40, 0x4f, ATA_UDMA5, }, + { "vt82c686a", PCI_DEVICE_ID_VIA_82C686, 0x10, 0x2f, ATA_UDMA4, }, + { "vt82c686", PCI_DEVICE_ID_VIA_82C686, 0x00, 0x0f, ATA_UDMA2, VIA_BAD_CLK66 }, + { "vt82c596b", PCI_DEVICE_ID_VIA_82C596, 0x10, 0x2f, ATA_UDMA4, }, + { "vt82c596a", PCI_DEVICE_ID_VIA_82C596, 0x00, 0x0f, ATA_UDMA2, VIA_BAD_CLK66 }, + { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x47, 0x4f, ATA_UDMA2, VIA_SET_FIFO }, + { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x40, 0x46, ATA_UDMA2, VIA_SET_FIFO | VIA_BAD_PREQ }, + { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x30, 0x3f, ATA_UDMA2, VIA_SET_FIFO }, + { "vt82c586a", PCI_DEVICE_ID_VIA_82C586_0, 0x20, 0x2f, ATA_UDMA2, VIA_SET_FIFO }, + { "vt82c586", PCI_DEVICE_ID_VIA_82C586_0, 0x00, 0x0f, 0x00, VIA_SET_FIFO }, + { "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, 0x00, VIA_SET_FIFO | VIA_NO_UNMASK }, + { "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, 0x00, VIA_SET_FIFO | VIA_NO_UNMASK | VIA_BAD_ID }, + { "vtxxxx", PCI_DEVICE_ID_VIA_ANON, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST }, + { NULL } +}; + +static const struct dmi_system_id no_atapi_dma_dmi_table[] = { + { + .ident = "AVERATEC 3200", + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, "AVERATEC"), + DMI_MATCH(DMI_BOARD_NAME, "3200"), + }, + }, + { } +}; + +struct via_port { + u8 cached_device; +}; + +/* + * Cable special cases + */ + +static const struct dmi_system_id cable_dmi_table[] = { + { + .ident = "Acer Ferrari 3400", + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, "Acer,Inc."), + DMI_MATCH(DMI_BOARD_NAME, "Ferrari 3400"), + }, + }, + { } +}; + +static int via_cable_override(struct pci_dev *pdev) +{ + /* Systems by DMI */ + if (dmi_check_system(cable_dmi_table)) + return 1; + /* Arima W730-K8/Targa Visionary 811/... */ + if (pdev->subsystem_vendor == 0x161F && pdev->subsystem_device == 0x2032) + return 1; + return 0; +} + + +/** + * via_cable_detect - cable detection + * @ap: ATA port + * + * Perform cable detection. Actually for the VIA case the BIOS + * already did this for us. We read the values provided by the + * BIOS. If you are using an 8235 in a non-PC configuration you + * may need to update this code. + * + * Hotplug also impacts on this. + */ + +static int via_cable_detect(struct ata_port *ap) { + const struct via_isa_bridge *config = ap->host->private_data; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 ata66; + + if (via_cable_override(pdev)) + return ATA_CBL_PATA40_SHORT; + + if ((config->flags & VIA_SATA_PATA) && ap->port_no == 0) + return ATA_CBL_SATA; + + /* Early chips are 40 wire */ + if (config->udma_mask < ATA_UDMA4) + return ATA_CBL_PATA40; + /* UDMA 66 chips have only drive side logic */ + else if (config->udma_mask < ATA_UDMA5) + return ATA_CBL_PATA_UNK; + /* UDMA 100 or later */ + pci_read_config_dword(pdev, 0x50, &ata66); + /* Check both the drive cable reporting bits, we might not have + two drives */ + if (ata66 & (0x10100000 >> (16 * ap->port_no))) + return ATA_CBL_PATA80; + /* Check with ACPI so we can spot BIOS reported SATA bridges */ + if (ata_acpi_init_gtm(ap) && + ata_acpi_cbl_80wire(ap, ata_acpi_init_gtm(ap))) + return ATA_CBL_PATA80; + return ATA_CBL_PATA40; +} + +static int via_pre_reset(struct ata_link *link, unsigned long deadline) +{ + struct ata_port *ap = link->ap; + const struct via_isa_bridge *config = ap->host->private_data; + + if (!(config->flags & VIA_NO_ENABLES)) { + static const struct pci_bits via_enable_bits[] = { + { 0x40, 1, 0x02, 0x02 }, + { 0x40, 1, 0x01, 0x01 } + }; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + if (!pci_test_config_bits(pdev, &via_enable_bits[ap->port_no])) + return -ENOENT; + } + + return ata_sff_prereset(link, deadline); +} + + +/** + * via_do_set_mode - set transfer mode data + * @ap: ATA interface + * @adev: ATA device + * @mode: ATA mode being programmed + * @set_ast: Set to program address setup + * @udma_type: UDMA mode/format of registers + * + * Program the VIA registers for DMA and PIO modes. Uses the ata timing + * support in order to compute modes. + * + * FIXME: Hotplug will require we serialize multiple mode changes + * on the two channels. + */ + +static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev, + int mode, int set_ast, int udma_type) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + struct ata_device *peer = ata_dev_pair(adev); + struct ata_timing t, p; + const int via_clock = 33333; /* Bus clock in kHz */ + const int T = 1000000000 / via_clock; + int UT = T; + int ut; + int offset = 3 - (2*ap->port_no) - adev->devno; + + switch (udma_type) { + case ATA_UDMA4: + UT = T / 2; break; + case ATA_UDMA5: + UT = T / 3; break; + case ATA_UDMA6: + UT = T / 4; break; + } + + /* Calculate the timing values we require */ + ata_timing_compute(adev, mode, &t, T, UT); + + /* We share 8bit timing so we must merge the constraints */ + if (peer) { + if (peer->pio_mode) { + ata_timing_compute(peer, peer->pio_mode, &p, T, UT); + ata_timing_merge(&p, &t, &t, ATA_TIMING_8BIT); + } + } + + /* Address setup is programmable but breaks on UDMA133 setups */ + if (set_ast) { + u8 setup; /* 2 bits per drive */ + int shift = 2 * offset; + + pci_read_config_byte(pdev, 0x4C, &setup); + setup &= ~(3 << shift); + setup |= (clamp_val(t.setup, 1, 4) - 1) << shift; + pci_write_config_byte(pdev, 0x4C, setup); + } + + /* Load the PIO mode bits */ + pci_write_config_byte(pdev, 0x4F - ap->port_no, + ((clamp_val(t.act8b, 1, 16) - 1) << 4) | (clamp_val(t.rec8b, 1, 16) - 1)); + pci_write_config_byte(pdev, 0x48 + offset, + ((clamp_val(t.active, 1, 16) - 1) << 4) | (clamp_val(t.recover, 1, 16) - 1)); + + /* Load the UDMA bits according to type */ + switch (udma_type) { + case ATA_UDMA2: + default: + ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 5) - 2)) : 0x03; + break; + case ATA_UDMA4: + ut = t.udma ? (0xe8 | (clamp_val(t.udma, 2, 9) - 2)) : 0x0f; + break; + case ATA_UDMA5: + ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07; + break; + case ATA_UDMA6: + ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07; + break; + } + + /* Set UDMA unless device is not UDMA capable */ + if (udma_type) { + u8 udma_etc; + + pci_read_config_byte(pdev, 0x50 + offset, &udma_etc); + + /* clear transfer mode bit */ + udma_etc &= ~0x20; + + if (t.udma) { + /* preserve 80-wire cable detection bit */ + udma_etc &= 0x10; + udma_etc |= ut; + } + + pci_write_config_byte(pdev, 0x50 + offset, udma_etc); + } +} + +static void via_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + const struct via_isa_bridge *config = ap->host->private_data; + int set_ast = (config->flags & VIA_BAD_AST) ? 0 : 1; + + via_do_set_mode(ap, adev, adev->pio_mode, set_ast, config->udma_mask); +} + +static void via_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + const struct via_isa_bridge *config = ap->host->private_data; + int set_ast = (config->flags & VIA_BAD_AST) ? 0 : 1; + + via_do_set_mode(ap, adev, adev->dma_mode, set_ast, config->udma_mask); +} + +/** + * via_mode_filter - filter buggy device/mode pairs + * @dev: ATA device + * @mask: Mode bitmask + * + * We need to apply some minimal filtering for old controllers and at least + * one breed of Transcend SSD. Return the updated mask. + */ + +static unsigned int via_mode_filter(struct ata_device *dev, unsigned int mask) +{ + struct ata_host *host = dev->link->ap->host; + const struct via_isa_bridge *config = host->private_data; + unsigned char model_num[ATA_ID_PROD_LEN + 1]; + + if (config->id == PCI_DEVICE_ID_VIA_82C586_0) { + ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num)); + if (strcmp(model_num, "TS64GSSD25-M") == 0) { + ata_dev_warn(dev, + "disabling UDMA mode due to reported lockups with this device\n"); + mask &= ~ ATA_MASK_UDMA; + } + } + + if (dev->class == ATA_DEV_ATAPI && + dmi_check_system(no_atapi_dma_dmi_table)) { + ata_dev_warn(dev, "controller locks up on ATAPI DMA, forcing PIO\n"); + mask &= ATA_MASK_PIO; + } + + return mask; +} + +/** + * via_tf_load - send taskfile registers to host controller + * @ap: Port to which output is sent + * @tf: ATA taskfile register set + * + * Outputs ATA taskfile to standard ATA host controller. + * + * Note: This is to fix the internal bug of via chipsets, which + * will reset the device register after changing the IEN bit on + * ctl register + */ +static void via_tf_load(struct ata_port *ap, const struct ata_taskfile *tf) +{ + struct ata_ioports *ioaddr = &ap->ioaddr; + struct via_port *vp = ap->private_data; + unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR; + int newctl = 0; + + if (tf->ctl != ap->last_ctl) { + iowrite8(tf->ctl, ioaddr->ctl_addr); + ap->last_ctl = tf->ctl; + ata_wait_idle(ap); + newctl = 1; + } + + if (tf->flags & ATA_TFLAG_DEVICE) { + iowrite8(tf->device, ioaddr->device_addr); + vp->cached_device = tf->device; + } else if (newctl) + iowrite8(vp->cached_device, ioaddr->device_addr); + + if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) { + WARN_ON_ONCE(!ioaddr->ctl_addr); + iowrite8(tf->hob_feature, ioaddr->feature_addr); + iowrite8(tf->hob_nsect, ioaddr->nsect_addr); + iowrite8(tf->hob_lbal, ioaddr->lbal_addr); + iowrite8(tf->hob_lbam, ioaddr->lbam_addr); + iowrite8(tf->hob_lbah, ioaddr->lbah_addr); + } + + if (is_addr) { + iowrite8(tf->feature, ioaddr->feature_addr); + iowrite8(tf->nsect, ioaddr->nsect_addr); + iowrite8(tf->lbal, ioaddr->lbal_addr); + iowrite8(tf->lbam, ioaddr->lbam_addr); + iowrite8(tf->lbah, ioaddr->lbah_addr); + } + + ata_wait_idle(ap); +} + +static int via_port_start(struct ata_port *ap) +{ + struct via_port *vp; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + int ret = ata_bmdma_port_start(ap); + if (ret < 0) + return ret; + + vp = devm_kzalloc(&pdev->dev, sizeof(struct via_port), GFP_KERNEL); + if (vp == NULL) + return -ENOMEM; + ap->private_data = vp; + return 0; +} + +static struct scsi_host_template via_sht = { + ATA_BMDMA_SHT(DRV_NAME), +}; + +static struct ata_port_operations via_port_ops = { + .inherits = &ata_bmdma_port_ops, + .cable_detect = via_cable_detect, + .set_piomode = via_set_piomode, + .set_dmamode = via_set_dmamode, + .prereset = via_pre_reset, + .sff_tf_load = via_tf_load, + .port_start = via_port_start, + .mode_filter = via_mode_filter, +}; + +static struct ata_port_operations via_port_ops_noirq = { + .inherits = &via_port_ops, + .sff_data_xfer = ata_sff_data_xfer32, +}; + +/** + * via_config_fifo - set up the FIFO + * @pdev: PCI device + * @flags: configuration flags + * + * Set the FIFO properties for this device if necessary. Used both on + * set up and on and the resume path + */ + +static void via_config_fifo(struct pci_dev *pdev, unsigned int flags) +{ + u8 enable; + + /* 0x40 low bits indicate enabled channels */ + pci_read_config_byte(pdev, 0x40 , &enable); + enable &= 3; + + if (flags & VIA_SET_FIFO) { + static const u8 fifo_setting[4] = {0x00, 0x60, 0x00, 0x20}; + u8 fifo; + + pci_read_config_byte(pdev, 0x43, &fifo); + + /* Clear PREQ# until DDACK# for errata */ + if (flags & VIA_BAD_PREQ) + fifo &= 0x7F; + else + fifo &= 0x9f; + /* Turn on FIFO for enabled channels */ + fifo |= fifo_setting[enable]; + pci_write_config_byte(pdev, 0x43, fifo); + } +} + +static void via_fixup(struct pci_dev *pdev, const struct via_isa_bridge *config) +{ + u32 timing; + + /* Initialise the FIFO for the enabled channels. */ + via_config_fifo(pdev, config->flags); + + if (config->udma_mask == ATA_UDMA4) { + /* The 66 MHz devices require we enable the clock */ + pci_read_config_dword(pdev, 0x50, &timing); + timing |= 0x80008; + pci_write_config_dword(pdev, 0x50, timing); + } + if (config->flags & VIA_BAD_CLK66) { + /* Disable the 66MHz clock on problem devices */ + pci_read_config_dword(pdev, 0x50, &timing); + timing &= ~0x80008; + pci_write_config_dword(pdev, 0x50, timing); + } +} + +/** + * via_init_one - discovery callback + * @pdev: PCI device + * @id: PCI table info + * + * A VIA IDE interface has been discovered. Figure out what revision + * and perform configuration work before handing it to the ATA layer + */ + +static int via_init_one(struct pci_dev *pdev, const struct pci_device_id *id) +{ + /* Early VIA without UDMA support */ + static const struct ata_port_info via_mwdma_info = { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .port_ops = &via_port_ops + }; + /* Ditto with IRQ masking required */ + static const struct ata_port_info via_mwdma_info_borked = { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .port_ops = &via_port_ops_noirq, + }; + /* VIA UDMA 33 devices (and borked 66) */ + static const struct ata_port_info via_udma33_info = { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA2, + .port_ops = &via_port_ops + }; + /* VIA UDMA 66 devices */ + static const struct ata_port_info via_udma66_info = { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA4, + .port_ops = &via_port_ops + }; + /* VIA UDMA 100 devices */ + static const struct ata_port_info via_udma100_info = { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA5, + .port_ops = &via_port_ops + }; + /* UDMA133 with bad AST (All current 133) */ + static const struct ata_port_info via_udma133_info = { + .flags = ATA_FLAG_SLAVE_POSS, + .pio_mask = ATA_PIO4, + .mwdma_mask = ATA_MWDMA2, + .udma_mask = ATA_UDMA6, /* FIXME: should check north bridge */ + .port_ops = &via_port_ops + }; + const struct ata_port_info *ppi[] = { NULL, NULL }; + struct pci_dev *isa; + const struct via_isa_bridge *config; + u8 enable; + unsigned long flags = id->driver_data; + int rc; + + ata_print_version_once(&pdev->dev, DRV_VERSION); + + rc = pcim_enable_device(pdev); + if (rc) + return rc; + + if (flags & VIA_IDFLAG_SINGLE) + ppi[1] = &ata_dummy_port_info; + + /* To find out how the IDE will behave and what features we + actually have to look at the bridge not the IDE controller */ + for (config = via_isa_bridges; config->id != PCI_DEVICE_ID_VIA_ANON; + config++) + if ((isa = pci_get_device(PCI_VENDOR_ID_VIA + + !!(config->flags & VIA_BAD_ID), + config->id, NULL))) { + u8 rev = isa->revision; + pci_dev_put(isa); + + if ((id->device == 0x0415 || id->device == 0x3164) && + (config->id != id->device)) + continue; + + if (rev >= config->rev_min && rev <= config->rev_max) + break; + } + + if (!(config->flags & VIA_NO_ENABLES)) { + /* 0x40 low bits indicate enabled channels */ + pci_read_config_byte(pdev, 0x40 , &enable); + enable &= 3; + if (enable == 0) + return -ENODEV; + } + + /* Clock set up */ + switch (config->udma_mask) { + case 0x00: + if (config->flags & VIA_NO_UNMASK) + ppi[0] = &via_mwdma_info_borked; + else + ppi[0] = &via_mwdma_info; + break; + case ATA_UDMA2: + ppi[0] = &via_udma33_info; + break; + case ATA_UDMA4: + ppi[0] = &via_udma66_info; + break; + case ATA_UDMA5: + ppi[0] = &via_udma100_info; + break; + case ATA_UDMA6: + ppi[0] = &via_udma133_info; + break; + default: + WARN_ON(1); + return -ENODEV; + } + + via_fixup(pdev, config); + + /* We have established the device type, now fire it up */ + return ata_pci_bmdma_init_one(pdev, ppi, &via_sht, (void *)config, 0); +} + +#ifdef CONFIG_PM_SLEEP +/** + * via_reinit_one - reinit after resume + * @pdev: PCI device + * + * Called when the VIA PATA device is resumed. We must then + * reconfigure the fifo and other setup we may have altered. In + * addition the kernel needs to have the resume methods on PCI + * quirk supported. + */ + +static int via_reinit_one(struct pci_dev *pdev) +{ + struct ata_host *host = pci_get_drvdata(pdev); + int rc; + + rc = ata_pci_device_do_resume(pdev); + if (rc) + return rc; + + via_fixup(pdev, host->private_data); + + ata_host_resume(host); + return 0; +} +#endif + +static const struct pci_device_id via[] = { + { PCI_VDEVICE(VIA, 0x0415), }, + { PCI_VDEVICE(VIA, 0x0571), }, + { PCI_VDEVICE(VIA, 0x0581), }, + { PCI_VDEVICE(VIA, 0x1571), }, + { PCI_VDEVICE(VIA, 0x3164), }, + { PCI_VDEVICE(VIA, 0x5324), }, + { PCI_VDEVICE(VIA, 0xC409), VIA_IDFLAG_SINGLE }, + { PCI_VDEVICE(VIA, 0x9001), VIA_IDFLAG_SINGLE }, + + { }, +}; + +static struct pci_driver via_pci_driver = { + .name = DRV_NAME, + .id_table = via, + .probe = via_init_one, + .remove = ata_pci_remove_one, +#ifdef CONFIG_PM_SLEEP + .suspend = ata_pci_device_suspend, + .resume = via_reinit_one, +#endif +}; + +module_pci_driver(via_pci_driver); + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for VIA PATA"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, via); +MODULE_VERSION(DRV_VERSION); |