diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/hwmon/abituguru3.c | 1303 |
1 files changed, 1303 insertions, 0 deletions
diff --git a/drivers/hwmon/abituguru3.c b/drivers/hwmon/abituguru3.c new file mode 100644 index 000000000..afb21f730 --- /dev/null +++ b/drivers/hwmon/abituguru3.c @@ -0,0 +1,1303 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * abituguru3.c + * + * Copyright (c) 2006-2008 Hans de Goede <hdegoede@redhat.com> + * Copyright (c) 2008 Alistair John Strachan <alistair@devzero.co.uk> + */ +/* + * This driver supports the sensor part of revision 3 of the custom Abit uGuru + * chip found on newer Abit uGuru motherboards. Note: because of lack of specs + * only reading the sensors and their settings is supported. + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/jiffies.h> +#include <linux/mutex.h> +#include <linux/err.h> +#include <linux/delay.h> +#include <linux/platform_device.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> +#include <linux/dmi.h> +#include <linux/io.h> + +/* uGuru3 bank addresses */ +#define ABIT_UGURU3_SETTINGS_BANK 0x01 +#define ABIT_UGURU3_SENSORS_BANK 0x08 +#define ABIT_UGURU3_MISC_BANK 0x09 +#define ABIT_UGURU3_ALARMS_START 0x1E +#define ABIT_UGURU3_SETTINGS_START 0x24 +#define ABIT_UGURU3_VALUES_START 0x80 +#define ABIT_UGURU3_BOARD_ID 0x0A +/* uGuru3 sensor bank flags */ /* Alarm if: */ +#define ABIT_UGURU3_TEMP_HIGH_ALARM_ENABLE 0x01 /* temp over warn */ +#define ABIT_UGURU3_VOLT_HIGH_ALARM_ENABLE 0x02 /* volt over max */ +#define ABIT_UGURU3_VOLT_LOW_ALARM_ENABLE 0x04 /* volt under min */ +#define ABIT_UGURU3_TEMP_HIGH_ALARM_FLAG 0x10 /* temp is over warn */ +#define ABIT_UGURU3_VOLT_HIGH_ALARM_FLAG 0x20 /* volt is over max */ +#define ABIT_UGURU3_VOLT_LOW_ALARM_FLAG 0x40 /* volt is under min */ +#define ABIT_UGURU3_FAN_LOW_ALARM_ENABLE 0x01 /* fan under min */ +#define ABIT_UGURU3_BEEP_ENABLE 0x08 /* beep if alarm */ +#define ABIT_UGURU3_SHUTDOWN_ENABLE 0x80 /* shutdown if alarm */ +/* sensor types */ +#define ABIT_UGURU3_IN_SENSOR 0 +#define ABIT_UGURU3_TEMP_SENSOR 1 +#define ABIT_UGURU3_FAN_SENSOR 2 + +/* + * Timeouts / Retries, if these turn out to need a lot of fiddling we could + * convert them to params. Determined by trial and error. I assume this is + * cpu-speed independent, since the ISA-bus and not the CPU should be the + * bottleneck. + */ +#define ABIT_UGURU3_WAIT_TIMEOUT 250 +/* + * Normally the 0xAC at the end of synchronize() is reported after the + * first read, but sometimes not and we need to poll + */ +#define ABIT_UGURU3_SYNCHRONIZE_TIMEOUT 5 +/* utility macros */ +#define ABIT_UGURU3_NAME "abituguru3" +#define ABIT_UGURU3_DEBUG(format, arg...) \ + do { \ + if (verbose) \ + pr_debug(format , ## arg); \ + } while (0) + +/* Macros to help calculate the sysfs_names array length */ +#define ABIT_UGURU3_MAX_NO_SENSORS 26 +/* + * sum of strlen +1 of: in??_input\0, in??_{min,max}\0, in??_{min,max}_alarm\0, + * in??_{min,max}_alarm_enable\0, in??_beep\0, in??_shutdown\0, in??_label\0 + */ +#define ABIT_UGURU3_IN_NAMES_LENGTH \ + (11 + 2 * 9 + 2 * 15 + 2 * 22 + 10 + 14 + 11) +/* + * sum of strlen +1 of: temp??_input\0, temp??_max\0, temp??_crit\0, + * temp??_alarm\0, temp??_alarm_enable\0, temp??_beep\0, temp??_shutdown\0, + * temp??_label\0 + */ +#define ABIT_UGURU3_TEMP_NAMES_LENGTH (13 + 11 + 12 + 13 + 20 + 12 + 16 + 13) +/* + * sum of strlen +1 of: fan??_input\0, fan??_min\0, fan??_alarm\0, + * fan??_alarm_enable\0, fan??_beep\0, fan??_shutdown\0, fan??_label\0 + */ +#define ABIT_UGURU3_FAN_NAMES_LENGTH (12 + 10 + 12 + 19 + 11 + 15 + 12) +/* + * Worst case scenario 16 in sensors (longest names_length) and the rest + * temp sensors (second longest names_length). + */ +#define ABIT_UGURU3_SYSFS_NAMES_LENGTH (16 * ABIT_UGURU3_IN_NAMES_LENGTH + \ + (ABIT_UGURU3_MAX_NO_SENSORS - 16) * ABIT_UGURU3_TEMP_NAMES_LENGTH) + +/* + * All the macros below are named identical to the openguru2 program + * reverse engineered by Louis Kruger, hence the names might not be 100% + * logical. I could come up with better names, but I prefer keeping the names + * identical so that this driver can be compared with his work more easily. + */ +/* Two i/o-ports are used by uGuru */ +#define ABIT_UGURU3_BASE 0x00E0 +#define ABIT_UGURU3_CMD 0x00 +#define ABIT_UGURU3_DATA 0x04 +#define ABIT_UGURU3_REGION_LENGTH 5 +/* + * The wait_xxx functions return this on success and the last contents + * of the DATA register (0-255) on failure. + */ +#define ABIT_UGURU3_SUCCESS -1 +/* uGuru status flags */ +#define ABIT_UGURU3_STATUS_READY_FOR_READ 0x01 +#define ABIT_UGURU3_STATUS_BUSY 0x02 + + +/* Structures */ +struct abituguru3_sensor_info { + const char *name; + int port; + int type; + int multiplier; + int divisor; + int offset; +}; + +/* Avoid use of flexible array members */ +#define ABIT_UGURU3_MAX_DMI_NAMES 2 + +struct abituguru3_motherboard_info { + u16 id; + const char *dmi_name[ABIT_UGURU3_MAX_DMI_NAMES + 1]; + /* + 1 -> end of sensors indicated by a sensor with name == NULL */ + struct abituguru3_sensor_info sensors[ABIT_UGURU3_MAX_NO_SENSORS + 1]; +}; + +/* + * For the Abit uGuru, we need to keep some data in memory. + * The structure is dynamically allocated, at the same time when a new + * abituguru3 device is allocated. + */ +struct abituguru3_data { + struct device *hwmon_dev; /* hwmon registered device */ + struct mutex update_lock; /* protect access to data and uGuru */ + unsigned short addr; /* uguru base address */ + bool valid; /* true if following fields are valid */ + unsigned long last_updated; /* In jiffies */ + + /* + * For convenience the sysfs attr and their names are generated + * automatically. We have max 10 entries per sensor (for in sensors) + */ + struct sensor_device_attribute_2 sysfs_attr[ABIT_UGURU3_MAX_NO_SENSORS + * 10]; + + /* Buffer to store the dynamically generated sysfs names */ + char sysfs_names[ABIT_UGURU3_SYSFS_NAMES_LENGTH]; + + /* Pointer to the sensors info for the detected motherboard */ + const struct abituguru3_sensor_info *sensors; + + /* + * The abituguru3 supports up to 48 sensors, and thus has registers + * sets for 48 sensors, for convenience reasons / simplicity of the + * code we always read and store all registers for all 48 sensors + */ + + /* Alarms for all 48 sensors (1 bit per sensor) */ + u8 alarms[48/8]; + + /* Value of all 48 sensors */ + u8 value[48]; + + /* + * Settings of all 48 sensors, note in and temp sensors (the first 32 + * sensors) have 3 bytes of settings, while fans only have 2 bytes, + * for convenience we use 3 bytes for all sensors + */ + u8 settings[48][3]; +}; + + +/* Constants */ +static const struct abituguru3_motherboard_info abituguru3_motherboards[] = { + { 0x000C, { NULL } /* Unknown, need DMI string */, { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 10, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, + { "MCH 2.5V", 5, 0, 20, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System", 25, 1, 1, 1, 0 }, + { "PWM", 26, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS FAN", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 35, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x000D, { NULL } /* Abit AW8, need DMI string */, { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 10, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, + { "MCH 2.5V", 5, 0, 20, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System", 25, 1, 1, 1, 0 }, + { "PWM1", 26, 1, 1, 1, 0 }, + { "PWM2", 27, 1, 1, 1, 0 }, + { "PWM3", 28, 1, 1, 1, 0 }, + { "PWM4", 29, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 35, 2, 60, 1, 0 }, + { "AUX2 Fan", 36, 2, 60, 1, 0 }, + { "AUX3 Fan", 37, 2, 60, 1, 0 }, + { "AUX4 Fan", 38, 2, 60, 1, 0 }, + { "AUX5 Fan", 39, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x000E, { NULL } /* AL-8, need DMI string */, { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 10, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, + { "MCH 2.5V", 5, 0, 20, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System", 25, 1, 1, 1, 0 }, + { "PWM", 26, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x000F, { NULL } /* Unknown, need DMI string */, { + + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 10, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, + { "MCH 2.5V", 5, 0, 20, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System", 25, 1, 1, 1, 0 }, + { "PWM", 26, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0010, { NULL } /* Abit NI8 SLI GR, need DMI string */, { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 10, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "NB 1.4V", 4, 0, 10, 1, 0 }, + { "SB 1.5V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "SYS", 25, 1, 1, 1, 0 }, + { "PWM", 26, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 35, 2, 60, 1, 0 }, + { "OTES1 Fan", 36, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0011, { "AT8 32X", NULL }, { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 20, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "CPU VDDA 2.5V", 6, 0, 20, 1, 0 }, + { "NB 1.8V", 4, 0, 10, 1, 0 }, + { "NB 1.8V Dual", 5, 0, 10, 1, 0 }, + { "HTV 1.2", 3, 0, 10, 1, 0 }, + { "PCIE 1.2V", 12, 0, 10, 1, 0 }, + { "NB 1.2V", 13, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "NB", 25, 1, 1, 1, 0 }, + { "System", 26, 1, 1, 1, 0 }, + { "PWM", 27, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 35, 2, 60, 1, 0 }, + { "AUX2 Fan", 36, 2, 60, 1, 0 }, + { "AUX3 Fan", 37, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0012, { NULL } /* Abit AN8 32X, need DMI string */, { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 20, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "HyperTransport", 3, 0, 10, 1, 0 }, + { "CPU VDDA 2.5V", 5, 0, 20, 1, 0 }, + { "NB", 4, 0, 10, 1, 0 }, + { "SB", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "SYS", 25, 1, 1, 1, 0 }, + { "PWM", 26, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 36, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0013, { NULL } /* Abit AW8D, need DMI string */, { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 10, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, + { "MCH 2.5V", 5, 0, 20, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System", 25, 1, 1, 1, 0 }, + { "PWM1", 26, 1, 1, 1, 0 }, + { "PWM2", 27, 1, 1, 1, 0 }, + { "PWM3", 28, 1, 1, 1, 0 }, + { "PWM4", 29, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 35, 2, 60, 1, 0 }, + { "AUX2 Fan", 36, 2, 60, 1, 0 }, + { "AUX3 Fan", 37, 2, 60, 1, 0 }, + { "AUX4 Fan", 38, 2, 60, 1, 0 }, + { "AUX5 Fan", 39, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0014, { "AB9", "AB9 Pro", NULL }, { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 10, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, + { "MCH 2.5V", 5, 0, 20, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System", 25, 1, 1, 1, 0 }, + { "PWM", 26, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0015, { NULL } /* Unknown, need DMI string */, { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR", 1, 0, 20, 1, 0 }, + { "DDR VTT", 2, 0, 10, 1, 0 }, + { "HyperTransport", 3, 0, 10, 1, 0 }, + { "CPU VDDA 2.5V", 5, 0, 20, 1, 0 }, + { "NB", 4, 0, 10, 1, 0 }, + { "SB", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "SYS", 25, 1, 1, 1, 0 }, + { "PWM", 26, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 33, 2, 60, 1, 0 }, + { "AUX2 Fan", 35, 2, 60, 1, 0 }, + { "AUX3 Fan", 36, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0016, { "AW9D-MAX", NULL }, { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR2", 1, 0, 20, 1, 0 }, + { "DDR2 VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "MCH & PCIE 1.5V", 4, 0, 10, 1, 0 }, + { "MCH 2.5V", 5, 0, 20, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System", 25, 1, 1, 1, 0 }, + { "PWM1", 26, 1, 1, 1, 0 }, + { "PWM2", 27, 1, 1, 1, 0 }, + { "PWM3", 28, 1, 1, 1, 0 }, + { "PWM4", 29, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "NB Fan", 33, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 35, 2, 60, 1, 0 }, + { "AUX2 Fan", 36, 2, 60, 1, 0 }, + { "AUX3 Fan", 37, 2, 60, 1, 0 }, + { "OTES1 Fan", 38, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0017, { NULL } /* Unknown, need DMI string */, { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR2", 1, 0, 20, 1, 0 }, + { "DDR2 VTT", 2, 0, 10, 1, 0 }, + { "HyperTransport", 3, 0, 10, 1, 0 }, + { "CPU VDDA 2.5V", 6, 0, 20, 1, 0 }, + { "NB 1.8V", 4, 0, 10, 1, 0 }, + { "NB 1.2V ", 13, 0, 10, 1, 0 }, + { "SB 1.2V", 5, 0, 10, 1, 0 }, + { "PCIE 1.2V", 12, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "ATX +3.3V", 10, 0, 20, 1, 0 }, + { "ATX 5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System", 26, 1, 1, 1, 0 }, + { "PWM", 27, 1, 1, 1, 0 }, + { "CPU FAN", 32, 2, 60, 1, 0 }, + { "SYS FAN", 34, 2, 60, 1, 0 }, + { "AUX1 FAN", 35, 2, 60, 1, 0 }, + { "AUX2 FAN", 36, 2, 60, 1, 0 }, + { "AUX3 FAN", 37, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0018, { "AB9 QuadGT", NULL }, { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR2", 1, 0, 20, 1, 0 }, + { "DDR2 VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT", 3, 0, 10, 1, 0 }, + { "MCH 1.25V", 4, 0, 10, 1, 0 }, + { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System", 25, 1, 1, 1, 0 }, + { "PWM Phase1", 26, 1, 1, 1, 0 }, + { "PWM Phase2", 27, 1, 1, 1, 0 }, + { "PWM Phase3", 28, 1, 1, 1, 0 }, + { "PWM Phase4", 29, 1, 1, 1, 0 }, + { "PWM Phase5", 30, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 33, 2, 60, 1, 0 }, + { "AUX2 Fan", 35, 2, 60, 1, 0 }, + { "AUX3 Fan", 36, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0019, { "IN9 32X MAX", NULL }, { + { "CPU Core", 7, 0, 10, 1, 0 }, + { "DDR2", 13, 0, 20, 1, 0 }, + { "DDR2 VTT", 14, 0, 10, 1, 0 }, + { "CPU VTT", 3, 0, 20, 1, 0 }, + { "NB 1.2V", 4, 0, 10, 1, 0 }, + { "SB 1.5V", 6, 0, 10, 1, 0 }, + { "HyperTransport", 5, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 12, 0, 60, 1, 0 }, + { "ATX +12V (4-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "ATX +3.3V", 10, 0, 20, 1, 0 }, + { "ATX 5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System", 25, 1, 1, 1, 0 }, + { "PWM Phase1", 26, 1, 1, 1, 0 }, + { "PWM Phase2", 27, 1, 1, 1, 0 }, + { "PWM Phase3", 28, 1, 1, 1, 0 }, + { "PWM Phase4", 29, 1, 1, 1, 0 }, + { "PWM Phase5", 30, 1, 1, 1, 0 }, + { "CPU FAN", 32, 2, 60, 1, 0 }, + { "SYS FAN", 34, 2, 60, 1, 0 }, + { "AUX1 FAN", 33, 2, 60, 1, 0 }, + { "AUX2 FAN", 35, 2, 60, 1, 0 }, + { "AUX3 FAN", 36, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x001A, { "IP35 Pro", "IP35 Pro XE", NULL }, { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR2", 1, 0, 20, 1, 0 }, + { "DDR2 VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT 1.2V", 3, 0, 10, 1, 0 }, + { "MCH 1.25V", 4, 0, 10, 1, 0 }, + { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (8-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System", 25, 1, 1, 1, 0 }, + { "PWM", 26, 1, 1, 1, 0 }, + { "PWM Phase2", 27, 1, 1, 1, 0 }, + { "PWM Phase3", 28, 1, 1, 1, 0 }, + { "PWM Phase4", 29, 1, 1, 1, 0 }, + { "PWM Phase5", 30, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 33, 2, 60, 1, 0 }, + { "AUX2 Fan", 35, 2, 60, 1, 0 }, + { "AUX3 Fan", 36, 2, 60, 1, 0 }, + { "AUX4 Fan", 37, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x001B, { NULL } /* Unknown, need DMI string */, { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR3", 1, 0, 20, 1, 0 }, + { "DDR3 VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT", 3, 0, 10, 1, 0 }, + { "MCH 1.25V", 4, 0, 10, 1, 0 }, + { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (8-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System", 25, 1, 1, 1, 0 }, + { "PWM Phase1", 26, 1, 1, 1, 0 }, + { "PWM Phase2", 27, 1, 1, 1, 0 }, + { "PWM Phase3", 28, 1, 1, 1, 0 }, + { "PWM Phase4", 29, 1, 1, 1, 0 }, + { "PWM Phase5", 30, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 33, 2, 60, 1, 0 }, + { "AUX2 Fan", 35, 2, 60, 1, 0 }, + { "AUX3 Fan", 36, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x001C, { "IX38 QuadGT", NULL }, { + { "CPU Core", 0, 0, 10, 1, 0 }, + { "DDR2", 1, 0, 20, 1, 0 }, + { "DDR2 VTT", 2, 0, 10, 1, 0 }, + { "CPU VTT", 3, 0, 10, 1, 0 }, + { "MCH 1.25V", 4, 0, 10, 1, 0 }, + { "ICHIO 1.5V", 5, 0, 10, 1, 0 }, + { "ICH 1.05V", 6, 0, 10, 1, 0 }, + { "ATX +12V (24-Pin)", 7, 0, 60, 1, 0 }, + { "ATX +12V (8-pin)", 8, 0, 60, 1, 0 }, + { "ATX +5V", 9, 0, 30, 1, 0 }, + { "+3.3V", 10, 0, 20, 1, 0 }, + { "5VSB", 11, 0, 30, 1, 0 }, + { "CPU", 24, 1, 1, 1, 0 }, + { "System", 25, 1, 1, 1, 0 }, + { "PWM Phase1", 26, 1, 1, 1, 0 }, + { "PWM Phase2", 27, 1, 1, 1, 0 }, + { "PWM Phase3", 28, 1, 1, 1, 0 }, + { "PWM Phase4", 29, 1, 1, 1, 0 }, + { "PWM Phase5", 30, 1, 1, 1, 0 }, + { "CPU Fan", 32, 2, 60, 1, 0 }, + { "SYS Fan", 34, 2, 60, 1, 0 }, + { "AUX1 Fan", 33, 2, 60, 1, 0 }, + { "AUX2 Fan", 35, 2, 60, 1, 0 }, + { "AUX3 Fan", 36, 2, 60, 1, 0 }, + { NULL, 0, 0, 0, 0, 0 } } + }, + { 0x0000, { NULL }, { { NULL, 0, 0, 0, 0, 0 } } } +}; + + +/* Insmod parameters */ +static bool force; +module_param(force, bool, 0); +MODULE_PARM_DESC(force, "Set to one to force detection."); +/* Default verbose is 1, since this driver is still in the testing phase */ +static bool verbose = 1; +module_param(verbose, bool, 0644); +MODULE_PARM_DESC(verbose, "Enable/disable verbose error reporting"); + +static const char *never_happen = "This should never happen."; +static const char *report_this = + "Please report this to the abituguru3 maintainer (see MAINTAINERS)"; + +/* wait while the uguru is busy (usually after a write) */ +static int abituguru3_wait_while_busy(struct abituguru3_data *data) +{ + u8 x; + int timeout = ABIT_UGURU3_WAIT_TIMEOUT; + + while ((x = inb_p(data->addr + ABIT_UGURU3_DATA)) & + ABIT_UGURU3_STATUS_BUSY) { + timeout--; + if (timeout == 0) + return x; + /* + * sleep a bit before our last try, to give the uGuru3 one + * last chance to respond. + */ + if (timeout == 1) + msleep(1); + } + return ABIT_UGURU3_SUCCESS; +} + +/* wait till uguru is ready to be read */ +static int abituguru3_wait_for_read(struct abituguru3_data *data) +{ + u8 x; + int timeout = ABIT_UGURU3_WAIT_TIMEOUT; + + while (!((x = inb_p(data->addr + ABIT_UGURU3_DATA)) & + ABIT_UGURU3_STATUS_READY_FOR_READ)) { + timeout--; + if (timeout == 0) + return x; + /* + * sleep a bit before our last try, to give the uGuru3 one + * last chance to respond. + */ + if (timeout == 1) + msleep(1); + } + return ABIT_UGURU3_SUCCESS; +} + +/* + * This synchronizes us with the uGuru3's protocol state machine, this + * must be done before each command. + */ +static int abituguru3_synchronize(struct abituguru3_data *data) +{ + int x, timeout = ABIT_UGURU3_SYNCHRONIZE_TIMEOUT; + + x = abituguru3_wait_while_busy(data); + if (x != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("synchronize timeout during initial busy " + "wait, status: 0x%02x\n", x); + return -EIO; + } + + outb(0x20, data->addr + ABIT_UGURU3_DATA); + x = abituguru3_wait_while_busy(data); + if (x != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x20, " + "status: 0x%02x\n", x); + return -EIO; + } + + outb(0x10, data->addr + ABIT_UGURU3_CMD); + x = abituguru3_wait_while_busy(data); + if (x != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x10, " + "status: 0x%02x\n", x); + return -EIO; + } + + outb(0x00, data->addr + ABIT_UGURU3_CMD); + x = abituguru3_wait_while_busy(data); + if (x != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("synchronize timeout after sending 0x00, " + "status: 0x%02x\n", x); + return -EIO; + } + + x = abituguru3_wait_for_read(data); + if (x != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("synchronize timeout waiting for read, " + "status: 0x%02x\n", x); + return -EIO; + } + + while ((x = inb(data->addr + ABIT_UGURU3_CMD)) != 0xAC) { + timeout--; + if (timeout == 0) { + ABIT_UGURU3_DEBUG("synchronize timeout cmd does not " + "hold 0xAC after synchronize, cmd: 0x%02x\n", + x); + return -EIO; + } + msleep(1); + } + return 0; +} + +/* + * Read count bytes from sensor sensor_addr in bank bank_addr and store the + * result in buf + */ +static int abituguru3_read(struct abituguru3_data *data, u8 bank, u8 offset, + u8 count, u8 *buf) +{ + int i, x; + + x = abituguru3_synchronize(data); + if (x) + return x; + + outb(0x1A, data->addr + ABIT_UGURU3_DATA); + x = abituguru3_wait_while_busy(data); + if (x != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " + "sending 0x1A, status: 0x%02x\n", (unsigned int)bank, + (unsigned int)offset, x); + return -EIO; + } + + outb(bank, data->addr + ABIT_UGURU3_CMD); + x = abituguru3_wait_while_busy(data); + if (x != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " + "sending the bank, status: 0x%02x\n", + (unsigned int)bank, (unsigned int)offset, x); + return -EIO; + } + + outb(offset, data->addr + ABIT_UGURU3_CMD); + x = abituguru3_wait_while_busy(data); + if (x != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " + "sending the offset, status: 0x%02x\n", + (unsigned int)bank, (unsigned int)offset, x); + return -EIO; + } + + outb(count, data->addr + ABIT_UGURU3_CMD); + x = abituguru3_wait_while_busy(data); + if (x != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("read from 0x%02x:0x%02x timed out after " + "sending the count, status: 0x%02x\n", + (unsigned int)bank, (unsigned int)offset, x); + return -EIO; + } + + for (i = 0; i < count; i++) { + x = abituguru3_wait_for_read(data); + if (x != ABIT_UGURU3_SUCCESS) { + ABIT_UGURU3_DEBUG("timeout reading byte %d from " + "0x%02x:0x%02x, status: 0x%02x\n", i, + (unsigned int)bank, (unsigned int)offset, x); + break; + } + buf[i] = inb(data->addr + ABIT_UGURU3_CMD); + } + return i; +} + +/* + * Sensor settings are stored 1 byte per offset with the bytes + * placed add consecutive offsets. + */ +static int abituguru3_read_increment_offset(struct abituguru3_data *data, + u8 bank, u8 offset, u8 count, + u8 *buf, int offset_count) +{ + int i, x; + + for (i = 0; i < offset_count; i++) { + x = abituguru3_read(data, bank, offset + i, count, + buf + i * count); + if (x != count) { + if (x < 0) + return x; + return i * count + x; + } + } + + return i * count; +} + +/* + * Following are the sysfs callback functions. These functions expect: + * sensor_device_attribute_2->index: index into the data->sensors array + * sensor_device_attribute_2->nr: register offset, bitmask or NA. + */ +static struct abituguru3_data *abituguru3_update_device(struct device *dev); + +static ssize_t show_value(struct device *dev, + struct device_attribute *devattr, char *buf) +{ + int value; + struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); + struct abituguru3_data *data = abituguru3_update_device(dev); + const struct abituguru3_sensor_info *sensor; + + if (!data) + return -EIO; + + sensor = &data->sensors[attr->index]; + + /* are we reading a setting, or is this a normal read? */ + if (attr->nr) + value = data->settings[sensor->port][attr->nr]; + else + value = data->value[sensor->port]; + + /* convert the value */ + value = (value * sensor->multiplier) / sensor->divisor + + sensor->offset; + + /* + * alternatively we could update the sensors settings struct for this, + * but then its contents would differ from the windows sw ini files + */ + if (sensor->type == ABIT_UGURU3_TEMP_SENSOR) + value *= 1000; + + return sprintf(buf, "%d\n", value); +} + +static ssize_t show_alarm(struct device *dev, + struct device_attribute *devattr, char *buf) +{ + int port; + struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); + struct abituguru3_data *data = abituguru3_update_device(dev); + + if (!data) + return -EIO; + + port = data->sensors[attr->index].port; + + /* + * See if the alarm bit for this sensor is set and if a bitmask is + * given in attr->nr also check if the alarm matches the type of alarm + * we're looking for (for volt it can be either low or high). The type + * is stored in a few readonly bits in the settings of the sensor. + */ + if ((data->alarms[port / 8] & (0x01 << (port % 8))) && + (!attr->nr || (data->settings[port][0] & attr->nr))) + return sprintf(buf, "1\n"); + else + return sprintf(buf, "0\n"); +} + +static ssize_t show_mask(struct device *dev, + struct device_attribute *devattr, char *buf) +{ + struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); + struct abituguru3_data *data = dev_get_drvdata(dev); + + if (data->settings[data->sensors[attr->index].port][0] & attr->nr) + return sprintf(buf, "1\n"); + else + return sprintf(buf, "0\n"); +} + +static ssize_t show_label(struct device *dev, + struct device_attribute *devattr, char *buf) +{ + struct sensor_device_attribute_2 *attr = to_sensor_dev_attr_2(devattr); + struct abituguru3_data *data = dev_get_drvdata(dev); + + return sprintf(buf, "%s\n", data->sensors[attr->index].name); +} + +static ssize_t show_name(struct device *dev, + struct device_attribute *devattr, char *buf) +{ + return sprintf(buf, "%s\n", ABIT_UGURU3_NAME); +} + +/* Sysfs attr templates, the real entries are generated automatically. */ +static const +struct sensor_device_attribute_2 abituguru3_sysfs_templ[3][10] = { { + SENSOR_ATTR_2(in%d_input, 0444, show_value, NULL, 0, 0), + SENSOR_ATTR_2(in%d_min, 0444, show_value, NULL, 1, 0), + SENSOR_ATTR_2(in%d_max, 0444, show_value, NULL, 2, 0), + SENSOR_ATTR_2(in%d_min_alarm, 0444, show_alarm, NULL, + ABIT_UGURU3_VOLT_LOW_ALARM_FLAG, 0), + SENSOR_ATTR_2(in%d_max_alarm, 0444, show_alarm, NULL, + ABIT_UGURU3_VOLT_HIGH_ALARM_FLAG, 0), + SENSOR_ATTR_2(in%d_beep, 0444, show_mask, NULL, + ABIT_UGURU3_BEEP_ENABLE, 0), + SENSOR_ATTR_2(in%d_shutdown, 0444, show_mask, NULL, + ABIT_UGURU3_SHUTDOWN_ENABLE, 0), + SENSOR_ATTR_2(in%d_min_alarm_enable, 0444, show_mask, NULL, + ABIT_UGURU3_VOLT_LOW_ALARM_ENABLE, 0), + SENSOR_ATTR_2(in%d_max_alarm_enable, 0444, show_mask, NULL, + ABIT_UGURU3_VOLT_HIGH_ALARM_ENABLE, 0), + SENSOR_ATTR_2(in%d_label, 0444, show_label, NULL, 0, 0) + }, { + SENSOR_ATTR_2(temp%d_input, 0444, show_value, NULL, 0, 0), + SENSOR_ATTR_2(temp%d_max, 0444, show_value, NULL, 1, 0), + SENSOR_ATTR_2(temp%d_crit, 0444, show_value, NULL, 2, 0), + SENSOR_ATTR_2(temp%d_alarm, 0444, show_alarm, NULL, 0, 0), + SENSOR_ATTR_2(temp%d_beep, 0444, show_mask, NULL, + ABIT_UGURU3_BEEP_ENABLE, 0), + SENSOR_ATTR_2(temp%d_shutdown, 0444, show_mask, NULL, + ABIT_UGURU3_SHUTDOWN_ENABLE, 0), + SENSOR_ATTR_2(temp%d_alarm_enable, 0444, show_mask, NULL, + ABIT_UGURU3_TEMP_HIGH_ALARM_ENABLE, 0), + SENSOR_ATTR_2(temp%d_label, 0444, show_label, NULL, 0, 0) + }, { + SENSOR_ATTR_2(fan%d_input, 0444, show_value, NULL, 0, 0), + SENSOR_ATTR_2(fan%d_min, 0444, show_value, NULL, 1, 0), + SENSOR_ATTR_2(fan%d_alarm, 0444, show_alarm, NULL, 0, 0), + SENSOR_ATTR_2(fan%d_beep, 0444, show_mask, NULL, + ABIT_UGURU3_BEEP_ENABLE, 0), + SENSOR_ATTR_2(fan%d_shutdown, 0444, show_mask, NULL, + ABIT_UGURU3_SHUTDOWN_ENABLE, 0), + SENSOR_ATTR_2(fan%d_alarm_enable, 0444, show_mask, NULL, + ABIT_UGURU3_FAN_LOW_ALARM_ENABLE, 0), + SENSOR_ATTR_2(fan%d_label, 0444, show_label, NULL, 0, 0) +} }; + +static struct sensor_device_attribute_2 abituguru3_sysfs_attr[] = { + SENSOR_ATTR_2(name, 0444, show_name, NULL, 0, 0), +}; + +static int abituguru3_probe(struct platform_device *pdev) +{ + const int no_sysfs_attr[3] = { 10, 8, 7 }; + int sensor_index[3] = { 0, 1, 1 }; + struct abituguru3_data *data; + int i, j, type, used, sysfs_names_free, sysfs_attr_i, res = -ENODEV; + char *sysfs_filename; + u8 buf[2]; + u16 id; + + data = devm_kzalloc(&pdev->dev, sizeof(struct abituguru3_data), + GFP_KERNEL); + if (!data) + return -ENOMEM; + + data->addr = platform_get_resource(pdev, IORESOURCE_IO, 0)->start; + mutex_init(&data->update_lock); + platform_set_drvdata(pdev, data); + + /* Read the motherboard ID */ + i = abituguru3_read(data, ABIT_UGURU3_MISC_BANK, ABIT_UGURU3_BOARD_ID, + 2, buf); + if (i != 2) + goto abituguru3_probe_error; + + /* Completely read the uGuru to see if one really is there */ + if (!abituguru3_update_device(&pdev->dev)) + goto abituguru3_probe_error; + + /* lookup the ID in our motherboard table */ + id = ((u16)buf[0] << 8) | (u16)buf[1]; + for (i = 0; abituguru3_motherboards[i].id; i++) + if (abituguru3_motherboards[i].id == id) + break; + if (!abituguru3_motherboards[i].id) { + pr_err("error unknown motherboard ID: %04X. %s\n", + (unsigned int)id, report_this); + goto abituguru3_probe_error; + } + data->sensors = abituguru3_motherboards[i].sensors; + + pr_info("found Abit uGuru3, motherboard ID: %04X\n", (unsigned int)id); + + /* Fill the sysfs attr array */ + sysfs_attr_i = 0; + sysfs_filename = data->sysfs_names; + sysfs_names_free = ABIT_UGURU3_SYSFS_NAMES_LENGTH; + for (i = 0; data->sensors[i].name; i++) { + /* Fail safe check, this should never happen! */ + if (i >= ABIT_UGURU3_MAX_NO_SENSORS) { + pr_err("Fatal error motherboard has more sensors then ABIT_UGURU3_MAX_NO_SENSORS. %s %s\n", + never_happen, report_this); + res = -ENAMETOOLONG; + goto abituguru3_probe_error; + } + type = data->sensors[i].type; + for (j = 0; j < no_sysfs_attr[type]; j++) { + used = snprintf(sysfs_filename, sysfs_names_free, + abituguru3_sysfs_templ[type][j].dev_attr.attr. + name, sensor_index[type]) + 1; + data->sysfs_attr[sysfs_attr_i] = + abituguru3_sysfs_templ[type][j]; + data->sysfs_attr[sysfs_attr_i].dev_attr.attr.name = + sysfs_filename; + data->sysfs_attr[sysfs_attr_i].index = i; + sysfs_filename += used; + sysfs_names_free -= used; + sysfs_attr_i++; + } + sensor_index[type]++; + } + /* Fail safe check, this should never happen! */ + if (sysfs_names_free < 0) { + pr_err("Fatal error ran out of space for sysfs attr names. %s %s\n", + never_happen, report_this); + res = -ENAMETOOLONG; + goto abituguru3_probe_error; + } + + /* Register sysfs hooks */ + for (i = 0; i < sysfs_attr_i; i++) + if (device_create_file(&pdev->dev, + &data->sysfs_attr[i].dev_attr)) + goto abituguru3_probe_error; + for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++) + if (device_create_file(&pdev->dev, + &abituguru3_sysfs_attr[i].dev_attr)) + goto abituguru3_probe_error; + + data->hwmon_dev = hwmon_device_register(&pdev->dev); + if (IS_ERR(data->hwmon_dev)) { + res = PTR_ERR(data->hwmon_dev); + goto abituguru3_probe_error; + } + + return 0; /* success */ + +abituguru3_probe_error: + for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++) + device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr); + for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++) + device_remove_file(&pdev->dev, + &abituguru3_sysfs_attr[i].dev_attr); + return res; +} + +static int abituguru3_remove(struct platform_device *pdev) +{ + int i; + struct abituguru3_data *data = platform_get_drvdata(pdev); + + hwmon_device_unregister(data->hwmon_dev); + for (i = 0; data->sysfs_attr[i].dev_attr.attr.name; i++) + device_remove_file(&pdev->dev, &data->sysfs_attr[i].dev_attr); + for (i = 0; i < ARRAY_SIZE(abituguru3_sysfs_attr); i++) + device_remove_file(&pdev->dev, + &abituguru3_sysfs_attr[i].dev_attr); + return 0; +} + +static struct abituguru3_data *abituguru3_update_device(struct device *dev) +{ + int i; + struct abituguru3_data *data = dev_get_drvdata(dev); + + mutex_lock(&data->update_lock); + if (!data->valid || time_after(jiffies, data->last_updated + HZ)) { + /* Clear data->valid while updating */ + data->valid = false; + /* Read alarms */ + if (abituguru3_read_increment_offset(data, + ABIT_UGURU3_SETTINGS_BANK, + ABIT_UGURU3_ALARMS_START, + 1, data->alarms, 48/8) != (48/8)) + goto LEAVE_UPDATE; + /* Read in and temp sensors (3 byte settings / sensor) */ + for (i = 0; i < 32; i++) { + if (abituguru3_read(data, ABIT_UGURU3_SENSORS_BANK, + ABIT_UGURU3_VALUES_START + i, + 1, &data->value[i]) != 1) + goto LEAVE_UPDATE; + if (abituguru3_read_increment_offset(data, + ABIT_UGURU3_SETTINGS_BANK, + ABIT_UGURU3_SETTINGS_START + i * 3, + 1, + data->settings[i], 3) != 3) + goto LEAVE_UPDATE; + } + /* Read temp sensors (2 byte settings / sensor) */ + for (i = 0; i < 16; i++) { + if (abituguru3_read(data, ABIT_UGURU3_SENSORS_BANK, + ABIT_UGURU3_VALUES_START + 32 + i, + 1, &data->value[32 + i]) != 1) + goto LEAVE_UPDATE; + if (abituguru3_read_increment_offset(data, + ABIT_UGURU3_SETTINGS_BANK, + ABIT_UGURU3_SETTINGS_START + 32 * 3 + + i * 2, 1, + data->settings[32 + i], 2) != 2) + goto LEAVE_UPDATE; + } + data->last_updated = jiffies; + data->valid = true; + } +LEAVE_UPDATE: + mutex_unlock(&data->update_lock); + if (data->valid) + return data; + else + return NULL; +} + +static int abituguru3_suspend(struct device *dev) +{ + struct abituguru3_data *data = dev_get_drvdata(dev); + /* + * make sure all communications with the uguru3 are done and no new + * ones are started + */ + mutex_lock(&data->update_lock); + return 0; +} + +static int abituguru3_resume(struct device *dev) +{ + struct abituguru3_data *data = dev_get_drvdata(dev); + mutex_unlock(&data->update_lock); + return 0; +} + +static DEFINE_SIMPLE_DEV_PM_OPS(abituguru3_pm, abituguru3_suspend, abituguru3_resume); + +static struct platform_driver abituguru3_driver = { + .driver = { + .name = ABIT_UGURU3_NAME, + .pm = pm_sleep_ptr(&abituguru3_pm), + }, + .probe = abituguru3_probe, + .remove = abituguru3_remove, +}; + +static int __init abituguru3_dmi_detect(void) +{ + const char *board_vendor, *board_name; + int i, err = (force) ? 1 : -ENODEV; + const char *const *dmi_name; + size_t sublen; + + board_vendor = dmi_get_system_info(DMI_BOARD_VENDOR); + if (!board_vendor || strcmp(board_vendor, "http://www.abit.com.tw/")) + return err; + + board_name = dmi_get_system_info(DMI_BOARD_NAME); + if (!board_name) + return err; + + /* + * At the moment, we don't care about the part of the vendor + * DMI string contained in brackets. Truncate the string at + * the first occurrence of a bracket. Trim any trailing space + * from the substring. + */ + sublen = strcspn(board_name, "("); + while (sublen > 0 && board_name[sublen - 1] == ' ') + sublen--; + + for (i = 0; abituguru3_motherboards[i].id; i++) { + dmi_name = abituguru3_motherboards[i].dmi_name; + for ( ; *dmi_name; dmi_name++) { + if (strlen(*dmi_name) != sublen) + continue; + if (!strncasecmp(board_name, *dmi_name, sublen)) + return 0; + } + } + + /* No match found */ + return 1; +} + +/* + * FIXME: Manual detection should die eventually; we need to collect stable + * DMI model names first before we can rely entirely on CONFIG_DMI. + */ + +static int __init abituguru3_detect(void) +{ + /* + * See if there is an uguru3 there. An idle uGuru3 will hold 0x00 or + * 0x08 at DATA and 0xAC at CMD. Sometimes the uGuru3 will hold 0x05 + * or 0x55 at CMD instead, why is unknown. + */ + u8 data_val = inb_p(ABIT_UGURU3_BASE + ABIT_UGURU3_DATA); + u8 cmd_val = inb_p(ABIT_UGURU3_BASE + ABIT_UGURU3_CMD); + if (((data_val == 0x00) || (data_val == 0x08)) && + ((cmd_val == 0xAC) || (cmd_val == 0x05) || + (cmd_val == 0x55))) + return 0; + + ABIT_UGURU3_DEBUG("no Abit uGuru3 found, data = 0x%02X, cmd = " + "0x%02X\n", (unsigned int)data_val, (unsigned int)cmd_val); + + if (force) { + pr_info("Assuming Abit uGuru3 is present because of \"force\" parameter\n"); + return 0; + } + + /* No uGuru3 found */ + return -ENODEV; +} + +static struct platform_device *abituguru3_pdev; + +static int __init abituguru3_init(void) +{ + struct resource res = { .flags = IORESOURCE_IO }; + int err; + + /* Attempt DMI detection first */ + err = abituguru3_dmi_detect(); + if (err < 0) + return err; + + /* + * Fall back to manual detection if there was no exact + * board name match, or force was specified. + */ + if (err > 0) { + err = abituguru3_detect(); + if (err) + return err; + + pr_warn("this motherboard was not detected using DMI. " + "Please send the output of \"dmidecode\" to the abituguru3 maintainer (see MAINTAINERS)\n"); + } + + err = platform_driver_register(&abituguru3_driver); + if (err) + goto exit; + + abituguru3_pdev = platform_device_alloc(ABIT_UGURU3_NAME, + ABIT_UGURU3_BASE); + if (!abituguru3_pdev) { + pr_err("Device allocation failed\n"); + err = -ENOMEM; + goto exit_driver_unregister; + } + + res.start = ABIT_UGURU3_BASE; + res.end = ABIT_UGURU3_BASE + ABIT_UGURU3_REGION_LENGTH - 1; + res.name = ABIT_UGURU3_NAME; + + err = platform_device_add_resources(abituguru3_pdev, &res, 1); + if (err) { + pr_err("Device resource addition failed (%d)\n", err); + goto exit_device_put; + } + + err = platform_device_add(abituguru3_pdev); + if (err) { + pr_err("Device addition failed (%d)\n", err); + goto exit_device_put; + } + + return 0; + +exit_device_put: + platform_device_put(abituguru3_pdev); +exit_driver_unregister: + platform_driver_unregister(&abituguru3_driver); +exit: + return err; +} + +static void __exit abituguru3_exit(void) +{ + platform_device_unregister(abituguru3_pdev); + platform_driver_unregister(&abituguru3_driver); +} + +MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>"); +MODULE_DESCRIPTION("Abit uGuru3 Sensor device"); +MODULE_LICENSE("GPL"); + +module_init(abituguru3_init); +module_exit(abituguru3_exit); |