diff options
Diffstat (limited to '')
-rw-r--r-- | drivers/hwmon/w83793.c | 2144 |
1 files changed, 2144 insertions, 0 deletions
diff --git a/drivers/hwmon/w83793.c b/drivers/hwmon/w83793.c new file mode 100644 index 000000000..a4926d907 --- /dev/null +++ b/drivers/hwmon/w83793.c @@ -0,0 +1,2144 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * w83793.c - Linux kernel driver for hardware monitoring + * Copyright (C) 2006 Winbond Electronics Corp. + * Yuan Mu + * Rudolf Marek <r.marek@assembler.cz> + * Copyright (C) 2009-2010 Sven Anders <anders@anduras.de>, ANDURAS AG. + * Watchdog driver part + * (Based partially on fschmd driver, + * Copyright 2007-2008 by Hans de Goede) + */ + +/* + * Supports following chips: + * + * Chip #vin #fanin #pwm #temp wchipid vendid i2c ISA + * w83793 10 12 8 6 0x7b 0x5ca3 yes no + */ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/i2c.h> +#include <linux/hwmon.h> +#include <linux/hwmon-vid.h> +#include <linux/hwmon-sysfs.h> +#include <linux/err.h> +#include <linux/mutex.h> +#include <linux/fs.h> +#include <linux/watchdog.h> +#include <linux/miscdevice.h> +#include <linux/uaccess.h> +#include <linux/kref.h> +#include <linux/notifier.h> +#include <linux/reboot.h> +#include <linux/jiffies.h> + +/* Default values */ +#define WATCHDOG_TIMEOUT 2 /* 2 minute default timeout */ + +/* Addresses to scan */ +static const unsigned short normal_i2c[] = { 0x2c, 0x2d, 0x2e, 0x2f, + I2C_CLIENT_END }; + +/* Insmod parameters */ + +static unsigned short force_subclients[4]; +module_param_array(force_subclients, short, NULL, 0); +MODULE_PARM_DESC(force_subclients, + "List of subclient addresses: {bus, clientaddr, subclientaddr1, subclientaddr2}"); + +static bool reset; +module_param(reset, bool, 0); +MODULE_PARM_DESC(reset, "Set to 1 to reset chip, not recommended"); + +static int timeout = WATCHDOG_TIMEOUT; /* default timeout in minutes */ +module_param(timeout, int, 0); +MODULE_PARM_DESC(timeout, + "Watchdog timeout in minutes. 2<= timeout <=255 (default=" + __MODULE_STRING(WATCHDOG_TIMEOUT) ")"); + +static bool nowayout = WATCHDOG_NOWAYOUT; +module_param(nowayout, bool, 0); +MODULE_PARM_DESC(nowayout, + "Watchdog cannot be stopped once started (default=" + __MODULE_STRING(WATCHDOG_NOWAYOUT) ")"); + +/* + * Address 0x00, 0x0d, 0x0e, 0x0f in all three banks are reserved + * as ID, Bank Select registers + */ +#define W83793_REG_BANKSEL 0x00 +#define W83793_REG_VENDORID 0x0d +#define W83793_REG_CHIPID 0x0e +#define W83793_REG_DEVICEID 0x0f + +#define W83793_REG_CONFIG 0x40 +#define W83793_REG_MFC 0x58 +#define W83793_REG_FANIN_CTRL 0x5c +#define W83793_REG_FANIN_SEL 0x5d +#define W83793_REG_I2C_ADDR 0x0b +#define W83793_REG_I2C_SUBADDR 0x0c +#define W83793_REG_VID_INA 0x05 +#define W83793_REG_VID_INB 0x06 +#define W83793_REG_VID_LATCHA 0x07 +#define W83793_REG_VID_LATCHB 0x08 +#define W83793_REG_VID_CTRL 0x59 + +#define W83793_REG_WDT_LOCK 0x01 +#define W83793_REG_WDT_ENABLE 0x02 +#define W83793_REG_WDT_STATUS 0x03 +#define W83793_REG_WDT_TIMEOUT 0x04 + +static u16 W83793_REG_TEMP_MODE[2] = { 0x5e, 0x5f }; + +#define TEMP_READ 0 +#define TEMP_CRIT 1 +#define TEMP_CRIT_HYST 2 +#define TEMP_WARN 3 +#define TEMP_WARN_HYST 4 +/* + * only crit and crit_hyst affect real-time alarm status + * current crit crit_hyst warn warn_hyst + */ +static u16 W83793_REG_TEMP[][5] = { + {0x1c, 0x78, 0x79, 0x7a, 0x7b}, + {0x1d, 0x7c, 0x7d, 0x7e, 0x7f}, + {0x1e, 0x80, 0x81, 0x82, 0x83}, + {0x1f, 0x84, 0x85, 0x86, 0x87}, + {0x20, 0x88, 0x89, 0x8a, 0x8b}, + {0x21, 0x8c, 0x8d, 0x8e, 0x8f}, +}; + +#define W83793_REG_TEMP_LOW_BITS 0x22 + +#define W83793_REG_BEEP(index) (0x53 + (index)) +#define W83793_REG_ALARM(index) (0x4b + (index)) + +#define W83793_REG_CLR_CHASSIS 0x4a /* SMI MASK4 */ +#define W83793_REG_IRQ_CTRL 0x50 +#define W83793_REG_OVT_CTRL 0x51 +#define W83793_REG_OVT_BEEP 0x52 + +#define IN_READ 0 +#define IN_MAX 1 +#define IN_LOW 2 +static const u16 W83793_REG_IN[][3] = { + /* Current, High, Low */ + {0x10, 0x60, 0x61}, /* Vcore A */ + {0x11, 0x62, 0x63}, /* Vcore B */ + {0x12, 0x64, 0x65}, /* Vtt */ + {0x14, 0x6a, 0x6b}, /* VSEN1 */ + {0x15, 0x6c, 0x6d}, /* VSEN2 */ + {0x16, 0x6e, 0x6f}, /* +3VSEN */ + {0x17, 0x70, 0x71}, /* +12VSEN */ + {0x18, 0x72, 0x73}, /* 5VDD */ + {0x19, 0x74, 0x75}, /* 5VSB */ + {0x1a, 0x76, 0x77}, /* VBAT */ +}; + +/* Low Bits of Vcore A/B Vtt Read/High/Low */ +static const u16 W83793_REG_IN_LOW_BITS[] = { 0x1b, 0x68, 0x69 }; +static u8 scale_in[] = { 2, 2, 2, 16, 16, 16, 8, 24, 24, 16 }; +static u8 scale_in_add[] = { 0, 0, 0, 0, 0, 0, 0, 150, 150, 0 }; + +#define W83793_REG_FAN(index) (0x23 + 2 * (index)) /* High byte */ +#define W83793_REG_FAN_MIN(index) (0x90 + 2 * (index)) /* High byte */ + +#define W83793_REG_PWM_DEFAULT 0xb2 +#define W83793_REG_PWM_ENABLE 0x207 +#define W83793_REG_PWM_UPTIME 0xc3 /* Unit in 0.1 second */ +#define W83793_REG_PWM_DOWNTIME 0xc4 /* Unit in 0.1 second */ +#define W83793_REG_TEMP_CRITICAL 0xc5 + +#define PWM_DUTY 0 +#define PWM_START 1 +#define PWM_NONSTOP 2 +#define PWM_STOP_TIME 3 +#define W83793_REG_PWM(index, nr) (((nr) == 0 ? 0xb3 : \ + (nr) == 1 ? 0x220 : 0x218) + (index)) + +/* bit field, fan1 is bit0, fan2 is bit1 ... */ +#define W83793_REG_TEMP_FAN_MAP(index) (0x201 + (index)) +#define W83793_REG_TEMP_TOL(index) (0x208 + (index)) +#define W83793_REG_TEMP_CRUISE(index) (0x210 + (index)) +#define W83793_REG_PWM_STOP_TIME(index) (0x228 + (index)) +#define W83793_REG_SF2_TEMP(index, nr) (0x230 + ((index) << 4) + (nr)) +#define W83793_REG_SF2_PWM(index, nr) (0x238 + ((index) << 4) + (nr)) + +static inline unsigned long FAN_FROM_REG(u16 val) +{ + if ((val >= 0xfff) || (val == 0)) + return 0; + return 1350000UL / val; +} + +static inline u16 FAN_TO_REG(long rpm) +{ + if (rpm <= 0) + return 0x0fff; + return clamp_val((1350000 + (rpm >> 1)) / rpm, 1, 0xffe); +} + +static inline unsigned long TIME_FROM_REG(u8 reg) +{ + return reg * 100; +} + +static inline u8 TIME_TO_REG(unsigned long val) +{ + return clamp_val((val + 50) / 100, 0, 0xff); +} + +static inline long TEMP_FROM_REG(s8 reg) +{ + return reg * 1000; +} + +static inline s8 TEMP_TO_REG(long val, s8 min, s8 max) +{ + return clamp_val((val + (val < 0 ? -500 : 500)) / 1000, min, max); +} + +struct w83793_data { + struct device *hwmon_dev; + struct mutex update_lock; + bool valid; /* true if following fields are valid */ + unsigned long last_updated; /* In jiffies */ + unsigned long last_nonvolatile; /* In jiffies, last time we update the + * nonvolatile registers + */ + + u8 bank; + u8 vrm; + u8 vid[2]; + u8 in[10][3]; /* Register value, read/high/low */ + u8 in_low_bits[3]; /* Additional resolution for VCore A/B Vtt */ + + u16 has_fan; /* Only fan1- fan5 has own pins */ + u16 fan[12]; /* Register value combine */ + u16 fan_min[12]; /* Register value combine */ + + s8 temp[6][5]; /* current, crit, crit_hyst,warn, warn_hyst */ + u8 temp_low_bits; /* Additional resolution TD1-TD4 */ + u8 temp_mode[2]; /* byte 0: Temp D1-D4 mode each has 2 bits + * byte 1: Temp R1,R2 mode, each has 1 bit + */ + u8 temp_critical; /* If reached all fan will be at full speed */ + u8 temp_fan_map[6]; /* Temp controls which pwm fan, bit field */ + + u8 has_pwm; + u8 has_temp; + u8 has_vid; + u8 pwm_enable; /* Register value, each Temp has 1 bit */ + u8 pwm_uptime; /* Register value */ + u8 pwm_downtime; /* Register value */ + u8 pwm_default; /* All fan default pwm, next poweron valid */ + u8 pwm[8][3]; /* Register value */ + u8 pwm_stop_time[8]; + u8 temp_cruise[6]; + + u8 alarms[5]; /* realtime status registers */ + u8 beeps[5]; + u8 beep_enable; + u8 tolerance[3]; /* Temp tolerance(Smart Fan I/II) */ + u8 sf2_pwm[6][7]; /* Smart FanII: Fan duty cycle */ + u8 sf2_temp[6][7]; /* Smart FanII: Temp level point */ + + /* watchdog */ + struct i2c_client *client; + struct mutex watchdog_lock; + struct list_head list; /* member of the watchdog_data_list */ + struct kref kref; + struct miscdevice watchdog_miscdev; + unsigned long watchdog_is_open; + char watchdog_expect_close; + char watchdog_name[10]; /* must be unique to avoid sysfs conflict */ + unsigned int watchdog_caused_reboot; + int watchdog_timeout; /* watchdog timeout in minutes */ +}; + +/* + * Somewhat ugly :( global data pointer list with all devices, so that + * we can find our device data as when using misc_register. There is no + * other method to get to one's device data from the open file-op and + * for usage in the reboot notifier callback. + */ +static LIST_HEAD(watchdog_data_list); + +/* Note this lock not only protect list access, but also data.kref access */ +static DEFINE_MUTEX(watchdog_data_mutex); + +/* + * Release our data struct when we're detached from the i2c client *and* all + * references to our watchdog device are released + */ +static void w83793_release_resources(struct kref *ref) +{ + struct w83793_data *data = container_of(ref, struct w83793_data, kref); + kfree(data); +} + +static u8 w83793_read_value(struct i2c_client *client, u16 reg); +static int w83793_write_value(struct i2c_client *client, u16 reg, u8 value); +static int w83793_probe(struct i2c_client *client); +static int w83793_detect(struct i2c_client *client, + struct i2c_board_info *info); +static void w83793_remove(struct i2c_client *client); +static void w83793_init_client(struct i2c_client *client); +static void w83793_update_nonvolatile(struct device *dev); +static struct w83793_data *w83793_update_device(struct device *dev); + +static const struct i2c_device_id w83793_id[] = { + { "w83793", 0 }, + { } +}; +MODULE_DEVICE_TABLE(i2c, w83793_id); + +static struct i2c_driver w83793_driver = { + .class = I2C_CLASS_HWMON, + .driver = { + .name = "w83793", + }, + .probe_new = w83793_probe, + .remove = w83793_remove, + .id_table = w83793_id, + .detect = w83793_detect, + .address_list = normal_i2c, +}; + +static ssize_t +vrm_show(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct w83793_data *data = dev_get_drvdata(dev); + return sprintf(buf, "%d\n", data->vrm); +} + +static ssize_t +show_vid(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct w83793_data *data = w83793_update_device(dev); + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int index = sensor_attr->index; + + return sprintf(buf, "%d\n", vid_from_reg(data->vid[index], data->vrm)); +} + +static ssize_t +vrm_store(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct w83793_data *data = dev_get_drvdata(dev); + unsigned long val; + int err; + + err = kstrtoul(buf, 10, &val); + if (err) + return err; + + if (val > 255) + return -EINVAL; + + data->vrm = val; + return count; +} + +#define ALARM_STATUS 0 +#define BEEP_ENABLE 1 +static ssize_t +show_alarm_beep(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct w83793_data *data = w83793_update_device(dev); + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int nr = sensor_attr->nr; + int index = sensor_attr->index >> 3; + int bit = sensor_attr->index & 0x07; + u8 val; + + if (nr == ALARM_STATUS) { + val = (data->alarms[index] >> (bit)) & 1; + } else { /* BEEP_ENABLE */ + val = (data->beeps[index] >> (bit)) & 1; + } + + return sprintf(buf, "%u\n", val); +} + +static ssize_t +store_beep(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct w83793_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int index = sensor_attr->index >> 3; + int shift = sensor_attr->index & 0x07; + u8 beep_bit = 1 << shift; + unsigned long val; + int err; + + err = kstrtoul(buf, 10, &val); + if (err) + return err; + + if (val > 1) + return -EINVAL; + + mutex_lock(&data->update_lock); + data->beeps[index] = w83793_read_value(client, W83793_REG_BEEP(index)); + data->beeps[index] &= ~beep_bit; + data->beeps[index] |= val << shift; + w83793_write_value(client, W83793_REG_BEEP(index), data->beeps[index]); + mutex_unlock(&data->update_lock); + + return count; +} + +static ssize_t +show_beep_enable(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct w83793_data *data = w83793_update_device(dev); + return sprintf(buf, "%u\n", (data->beep_enable >> 1) & 0x01); +} + +static ssize_t +store_beep_enable(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct w83793_data *data = i2c_get_clientdata(client); + unsigned long val; + int err; + + err = kstrtoul(buf, 10, &val); + if (err) + return err; + + if (val > 1) + return -EINVAL; + + mutex_lock(&data->update_lock); + data->beep_enable = w83793_read_value(client, W83793_REG_OVT_BEEP) + & 0xfd; + data->beep_enable |= val << 1; + w83793_write_value(client, W83793_REG_OVT_BEEP, data->beep_enable); + mutex_unlock(&data->update_lock); + + return count; +} + +/* Write 0 to clear chassis alarm */ +static ssize_t +store_chassis_clear(struct device *dev, + struct device_attribute *attr, const char *buf, + size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct w83793_data *data = i2c_get_clientdata(client); + unsigned long val; + u8 reg; + int err; + + err = kstrtoul(buf, 10, &val); + if (err) + return err; + if (val) + return -EINVAL; + + mutex_lock(&data->update_lock); + reg = w83793_read_value(client, W83793_REG_CLR_CHASSIS); + w83793_write_value(client, W83793_REG_CLR_CHASSIS, reg | 0x80); + data->valid = false; /* Force cache refresh */ + mutex_unlock(&data->update_lock); + return count; +} + +#define FAN_INPUT 0 +#define FAN_MIN 1 +static ssize_t +show_fan(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int nr = sensor_attr->nr; + int index = sensor_attr->index; + struct w83793_data *data = w83793_update_device(dev); + u16 val; + + if (nr == FAN_INPUT) + val = data->fan[index] & 0x0fff; + else + val = data->fan_min[index] & 0x0fff; + + return sprintf(buf, "%lu\n", FAN_FROM_REG(val)); +} + +static ssize_t +store_fan_min(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int index = sensor_attr->index; + struct i2c_client *client = to_i2c_client(dev); + struct w83793_data *data = i2c_get_clientdata(client); + unsigned long val; + int err; + + err = kstrtoul(buf, 10, &val); + if (err) + return err; + val = FAN_TO_REG(val); + + mutex_lock(&data->update_lock); + data->fan_min[index] = val; + w83793_write_value(client, W83793_REG_FAN_MIN(index), + (val >> 8) & 0xff); + w83793_write_value(client, W83793_REG_FAN_MIN(index) + 1, val & 0xff); + mutex_unlock(&data->update_lock); + + return count; +} + +static ssize_t +show_pwm(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + struct w83793_data *data = w83793_update_device(dev); + u16 val; + int nr = sensor_attr->nr; + int index = sensor_attr->index; + + if (nr == PWM_STOP_TIME) + val = TIME_FROM_REG(data->pwm_stop_time[index]); + else + val = (data->pwm[index][nr] & 0x3f) << 2; + + return sprintf(buf, "%d\n", val); +} + +static ssize_t +store_pwm(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct w83793_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int nr = sensor_attr->nr; + int index = sensor_attr->index; + unsigned long val; + int err; + + err = kstrtoul(buf, 10, &val); + if (err) + return err; + + mutex_lock(&data->update_lock); + if (nr == PWM_STOP_TIME) { + val = TIME_TO_REG(val); + data->pwm_stop_time[index] = val; + w83793_write_value(client, W83793_REG_PWM_STOP_TIME(index), + val); + } else { + val = clamp_val(val, 0, 0xff) >> 2; + data->pwm[index][nr] = + w83793_read_value(client, W83793_REG_PWM(index, nr)) & 0xc0; + data->pwm[index][nr] |= val; + w83793_write_value(client, W83793_REG_PWM(index, nr), + data->pwm[index][nr]); + } + + mutex_unlock(&data->update_lock); + return count; +} + +static ssize_t +show_temp(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int nr = sensor_attr->nr; + int index = sensor_attr->index; + struct w83793_data *data = w83793_update_device(dev); + long temp = TEMP_FROM_REG(data->temp[index][nr]); + + if (nr == TEMP_READ && index < 4) { /* Only TD1-TD4 have low bits */ + int low = ((data->temp_low_bits >> (index * 2)) & 0x03) * 250; + temp += temp > 0 ? low : -low; + } + return sprintf(buf, "%ld\n", temp); +} + +static ssize_t +store_temp(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int nr = sensor_attr->nr; + int index = sensor_attr->index; + struct i2c_client *client = to_i2c_client(dev); + struct w83793_data *data = i2c_get_clientdata(client); + long tmp; + int err; + + err = kstrtol(buf, 10, &tmp); + if (err) + return err; + + mutex_lock(&data->update_lock); + data->temp[index][nr] = TEMP_TO_REG(tmp, -128, 127); + w83793_write_value(client, W83793_REG_TEMP[index][nr], + data->temp[index][nr]); + mutex_unlock(&data->update_lock); + return count; +} + +/* + * TD1-TD4 + * each has 4 mode:(2 bits) + * 0: Stop monitor + * 1: Use internal temp sensor(default) + * 2: Reserved + * 3: Use sensor in Intel CPU and get result by PECI + * + * TR1-TR2 + * each has 2 mode:(1 bit) + * 0: Disable temp sensor monitor + * 1: To enable temp sensors monitor + */ + +/* 0 disable, 6 PECI */ +static u8 TO_TEMP_MODE[] = { 0, 0, 0, 6 }; + +static ssize_t +show_temp_mode(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct w83793_data *data = w83793_update_device(dev); + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int index = sensor_attr->index; + u8 mask = (index < 4) ? 0x03 : 0x01; + u8 shift = (index < 4) ? (2 * index) : (index - 4); + u8 tmp; + index = (index < 4) ? 0 : 1; + + tmp = (data->temp_mode[index] >> shift) & mask; + + /* for the internal sensor, found out if diode or thermistor */ + if (tmp == 1) + tmp = index == 0 ? 3 : 4; + else + tmp = TO_TEMP_MODE[tmp]; + + return sprintf(buf, "%d\n", tmp); +} + +static ssize_t +store_temp_mode(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct w83793_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int index = sensor_attr->index; + u8 mask = (index < 4) ? 0x03 : 0x01; + u8 shift = (index < 4) ? (2 * index) : (index - 4); + unsigned long val; + int err; + + err = kstrtoul(buf, 10, &val); + if (err) + return err; + + /* transform the sysfs interface values into table above */ + if ((val == 6) && (index < 4)) { + val -= 3; + } else if ((val == 3 && index < 4) + || (val == 4 && index >= 4)) { + /* transform diode or thermistor into internal enable */ + val = !!val; + } else { + return -EINVAL; + } + + index = (index < 4) ? 0 : 1; + mutex_lock(&data->update_lock); + data->temp_mode[index] = + w83793_read_value(client, W83793_REG_TEMP_MODE[index]); + data->temp_mode[index] &= ~(mask << shift); + data->temp_mode[index] |= val << shift; + w83793_write_value(client, W83793_REG_TEMP_MODE[index], + data->temp_mode[index]); + mutex_unlock(&data->update_lock); + + return count; +} + +#define SETUP_PWM_DEFAULT 0 +#define SETUP_PWM_UPTIME 1 /* Unit in 0.1s */ +#define SETUP_PWM_DOWNTIME 2 /* Unit in 0.1s */ +#define SETUP_TEMP_CRITICAL 3 +static ssize_t +show_sf_setup(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int nr = sensor_attr->nr; + struct w83793_data *data = w83793_update_device(dev); + u32 val = 0; + + if (nr == SETUP_PWM_DEFAULT) + val = (data->pwm_default & 0x3f) << 2; + else if (nr == SETUP_PWM_UPTIME) + val = TIME_FROM_REG(data->pwm_uptime); + else if (nr == SETUP_PWM_DOWNTIME) + val = TIME_FROM_REG(data->pwm_downtime); + else if (nr == SETUP_TEMP_CRITICAL) + val = TEMP_FROM_REG(data->temp_critical & 0x7f); + + return sprintf(buf, "%d\n", val); +} + +static ssize_t +store_sf_setup(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int nr = sensor_attr->nr; + struct i2c_client *client = to_i2c_client(dev); + struct w83793_data *data = i2c_get_clientdata(client); + long val; + int err; + + err = kstrtol(buf, 10, &val); + if (err) + return err; + + mutex_lock(&data->update_lock); + if (nr == SETUP_PWM_DEFAULT) { + data->pwm_default = + w83793_read_value(client, W83793_REG_PWM_DEFAULT) & 0xc0; + data->pwm_default |= clamp_val(val, 0, 0xff) >> 2; + w83793_write_value(client, W83793_REG_PWM_DEFAULT, + data->pwm_default); + } else if (nr == SETUP_PWM_UPTIME) { + data->pwm_uptime = TIME_TO_REG(val); + data->pwm_uptime += data->pwm_uptime == 0 ? 1 : 0; + w83793_write_value(client, W83793_REG_PWM_UPTIME, + data->pwm_uptime); + } else if (nr == SETUP_PWM_DOWNTIME) { + data->pwm_downtime = TIME_TO_REG(val); + data->pwm_downtime += data->pwm_downtime == 0 ? 1 : 0; + w83793_write_value(client, W83793_REG_PWM_DOWNTIME, + data->pwm_downtime); + } else { /* SETUP_TEMP_CRITICAL */ + data->temp_critical = + w83793_read_value(client, W83793_REG_TEMP_CRITICAL) & 0x80; + data->temp_critical |= TEMP_TO_REG(val, 0, 0x7f); + w83793_write_value(client, W83793_REG_TEMP_CRITICAL, + data->temp_critical); + } + + mutex_unlock(&data->update_lock); + return count; +} + +/* + * Temp SmartFan control + * TEMP_FAN_MAP + * Temp channel control which pwm fan, bitfield, bit 0 indicate pwm1... + * It's possible two or more temp channels control the same fan, w83793 + * always prefers to pick the most critical request and applies it to + * the related Fan. + * It's possible one fan is not in any mapping of 6 temp channels, this + * means the fan is manual mode + * + * TEMP_PWM_ENABLE + * Each temp channel has its own SmartFan mode, and temp channel + * control fans that are set by TEMP_FAN_MAP + * 0: SmartFanII mode + * 1: Thermal Cruise Mode + * + * TEMP_CRUISE + * Target temperature in thermal cruise mode, w83793 will try to turn + * fan speed to keep the temperature of target device around this + * temperature. + * + * TEMP_TOLERANCE + * If Temp higher or lower than target with this tolerance, w83793 + * will take actions to speed up or slow down the fan to keep the + * temperature within the tolerance range. + */ + +#define TEMP_FAN_MAP 0 +#define TEMP_PWM_ENABLE 1 +#define TEMP_CRUISE 2 +#define TEMP_TOLERANCE 3 +static ssize_t +show_sf_ctrl(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int nr = sensor_attr->nr; + int index = sensor_attr->index; + struct w83793_data *data = w83793_update_device(dev); + u32 val; + + if (nr == TEMP_FAN_MAP) { + val = data->temp_fan_map[index]; + } else if (nr == TEMP_PWM_ENABLE) { + /* +2 to transform into 2 and 3 to conform with sysfs intf */ + val = ((data->pwm_enable >> index) & 0x01) + 2; + } else if (nr == TEMP_CRUISE) { + val = TEMP_FROM_REG(data->temp_cruise[index] & 0x7f); + } else { /* TEMP_TOLERANCE */ + val = data->tolerance[index >> 1] >> ((index & 0x01) ? 4 : 0); + val = TEMP_FROM_REG(val & 0x0f); + } + return sprintf(buf, "%d\n", val); +} + +static ssize_t +store_sf_ctrl(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int nr = sensor_attr->nr; + int index = sensor_attr->index; + struct i2c_client *client = to_i2c_client(dev); + struct w83793_data *data = i2c_get_clientdata(client); + long val; + int err; + + err = kstrtol(buf, 10, &val); + if (err) + return err; + + mutex_lock(&data->update_lock); + if (nr == TEMP_FAN_MAP) { + val = clamp_val(val, 0, 255); + w83793_write_value(client, W83793_REG_TEMP_FAN_MAP(index), val); + data->temp_fan_map[index] = val; + } else if (nr == TEMP_PWM_ENABLE) { + if (val == 2 || val == 3) { + data->pwm_enable = + w83793_read_value(client, W83793_REG_PWM_ENABLE); + if (val - 2) + data->pwm_enable |= 1 << index; + else + data->pwm_enable &= ~(1 << index); + w83793_write_value(client, W83793_REG_PWM_ENABLE, + data->pwm_enable); + } else { + mutex_unlock(&data->update_lock); + return -EINVAL; + } + } else if (nr == TEMP_CRUISE) { + data->temp_cruise[index] = + w83793_read_value(client, W83793_REG_TEMP_CRUISE(index)); + data->temp_cruise[index] &= 0x80; + data->temp_cruise[index] |= TEMP_TO_REG(val, 0, 0x7f); + + w83793_write_value(client, W83793_REG_TEMP_CRUISE(index), + data->temp_cruise[index]); + } else { /* TEMP_TOLERANCE */ + int i = index >> 1; + u8 shift = (index & 0x01) ? 4 : 0; + data->tolerance[i] = + w83793_read_value(client, W83793_REG_TEMP_TOL(i)); + + data->tolerance[i] &= ~(0x0f << shift); + data->tolerance[i] |= TEMP_TO_REG(val, 0, 0x0f) << shift; + w83793_write_value(client, W83793_REG_TEMP_TOL(i), + data->tolerance[i]); + } + + mutex_unlock(&data->update_lock); + return count; +} + +static ssize_t +show_sf2_pwm(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int nr = sensor_attr->nr; + int index = sensor_attr->index; + struct w83793_data *data = w83793_update_device(dev); + + return sprintf(buf, "%d\n", (data->sf2_pwm[index][nr] & 0x3f) << 2); +} + +static ssize_t +store_sf2_pwm(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct w83793_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int nr = sensor_attr->nr; + int index = sensor_attr->index; + unsigned long val; + int err; + + err = kstrtoul(buf, 10, &val); + if (err) + return err; + val = clamp_val(val, 0, 0xff) >> 2; + + mutex_lock(&data->update_lock); + data->sf2_pwm[index][nr] = + w83793_read_value(client, W83793_REG_SF2_PWM(index, nr)) & 0xc0; + data->sf2_pwm[index][nr] |= val; + w83793_write_value(client, W83793_REG_SF2_PWM(index, nr), + data->sf2_pwm[index][nr]); + mutex_unlock(&data->update_lock); + return count; +} + +static ssize_t +show_sf2_temp(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int nr = sensor_attr->nr; + int index = sensor_attr->index; + struct w83793_data *data = w83793_update_device(dev); + + return sprintf(buf, "%ld\n", + TEMP_FROM_REG(data->sf2_temp[index][nr] & 0x7f)); +} + +static ssize_t +store_sf2_temp(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct i2c_client *client = to_i2c_client(dev); + struct w83793_data *data = i2c_get_clientdata(client); + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int nr = sensor_attr->nr; + int index = sensor_attr->index; + long val; + int err; + + err = kstrtol(buf, 10, &val); + if (err) + return err; + val = TEMP_TO_REG(val, 0, 0x7f); + + mutex_lock(&data->update_lock); + data->sf2_temp[index][nr] = + w83793_read_value(client, W83793_REG_SF2_TEMP(index, nr)) & 0x80; + data->sf2_temp[index][nr] |= val; + w83793_write_value(client, W83793_REG_SF2_TEMP(index, nr), + data->sf2_temp[index][nr]); + mutex_unlock(&data->update_lock); + return count; +} + +/* only Vcore A/B and Vtt have additional 2 bits precision */ +static ssize_t +show_in(struct device *dev, struct device_attribute *attr, char *buf) +{ + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int nr = sensor_attr->nr; + int index = sensor_attr->index; + struct w83793_data *data = w83793_update_device(dev); + u16 val = data->in[index][nr]; + + if (index < 3) { + val <<= 2; + val += (data->in_low_bits[nr] >> (index * 2)) & 0x3; + } + /* voltage inputs 5VDD and 5VSB needs 150mV offset */ + val = val * scale_in[index] + scale_in_add[index]; + return sprintf(buf, "%d\n", val); +} + +static ssize_t +store_in(struct device *dev, struct device_attribute *attr, + const char *buf, size_t count) +{ + struct sensor_device_attribute_2 *sensor_attr = + to_sensor_dev_attr_2(attr); + int nr = sensor_attr->nr; + int index = sensor_attr->index; + struct i2c_client *client = to_i2c_client(dev); + struct w83793_data *data = i2c_get_clientdata(client); + unsigned long val; + int err; + + err = kstrtoul(buf, 10, &val); + if (err) + return err; + val = (val + scale_in[index] / 2) / scale_in[index]; + + mutex_lock(&data->update_lock); + if (index > 2) { + /* fix the limit values of 5VDD and 5VSB to ALARM mechanism */ + if (nr == 1 || nr == 2) + val -= scale_in_add[index] / scale_in[index]; + val = clamp_val(val, 0, 255); + } else { + val = clamp_val(val, 0, 0x3FF); + data->in_low_bits[nr] = + w83793_read_value(client, W83793_REG_IN_LOW_BITS[nr]); + data->in_low_bits[nr] &= ~(0x03 << (2 * index)); + data->in_low_bits[nr] |= (val & 0x03) << (2 * index); + w83793_write_value(client, W83793_REG_IN_LOW_BITS[nr], + data->in_low_bits[nr]); + val >>= 2; + } + data->in[index][nr] = val; + w83793_write_value(client, W83793_REG_IN[index][nr], + data->in[index][nr]); + mutex_unlock(&data->update_lock); + return count; +} + +#define NOT_USED -1 + +#define SENSOR_ATTR_IN(index) \ + SENSOR_ATTR_2(in##index##_input, S_IRUGO, show_in, NULL, \ + IN_READ, index), \ + SENSOR_ATTR_2(in##index##_max, S_IRUGO | S_IWUSR, show_in, \ + store_in, IN_MAX, index), \ + SENSOR_ATTR_2(in##index##_min, S_IRUGO | S_IWUSR, show_in, \ + store_in, IN_LOW, index), \ + SENSOR_ATTR_2(in##index##_alarm, S_IRUGO, show_alarm_beep, \ + NULL, ALARM_STATUS, index + ((index > 2) ? 1 : 0)), \ + SENSOR_ATTR_2(in##index##_beep, S_IWUSR | S_IRUGO, \ + show_alarm_beep, store_beep, BEEP_ENABLE, \ + index + ((index > 2) ? 1 : 0)) + +#define SENSOR_ATTR_FAN(index) \ + SENSOR_ATTR_2(fan##index##_alarm, S_IRUGO, show_alarm_beep, \ + NULL, ALARM_STATUS, index + 17), \ + SENSOR_ATTR_2(fan##index##_beep, S_IWUSR | S_IRUGO, \ + show_alarm_beep, store_beep, BEEP_ENABLE, index + 17), \ + SENSOR_ATTR_2(fan##index##_input, S_IRUGO, show_fan, \ + NULL, FAN_INPUT, index - 1), \ + SENSOR_ATTR_2(fan##index##_min, S_IWUSR | S_IRUGO, \ + show_fan, store_fan_min, FAN_MIN, index - 1) + +#define SENSOR_ATTR_PWM(index) \ + SENSOR_ATTR_2(pwm##index, S_IWUSR | S_IRUGO, show_pwm, \ + store_pwm, PWM_DUTY, index - 1), \ + SENSOR_ATTR_2(pwm##index##_nonstop, S_IWUSR | S_IRUGO, \ + show_pwm, store_pwm, PWM_NONSTOP, index - 1), \ + SENSOR_ATTR_2(pwm##index##_start, S_IWUSR | S_IRUGO, \ + show_pwm, store_pwm, PWM_START, index - 1), \ + SENSOR_ATTR_2(pwm##index##_stop_time, S_IWUSR | S_IRUGO, \ + show_pwm, store_pwm, PWM_STOP_TIME, index - 1) + +#define SENSOR_ATTR_TEMP(index) \ + SENSOR_ATTR_2(temp##index##_type, S_IRUGO | S_IWUSR, \ + show_temp_mode, store_temp_mode, NOT_USED, index - 1), \ + SENSOR_ATTR_2(temp##index##_input, S_IRUGO, show_temp, \ + NULL, TEMP_READ, index - 1), \ + SENSOR_ATTR_2(temp##index##_max, S_IRUGO | S_IWUSR, show_temp, \ + store_temp, TEMP_CRIT, index - 1), \ + SENSOR_ATTR_2(temp##index##_max_hyst, S_IRUGO | S_IWUSR, \ + show_temp, store_temp, TEMP_CRIT_HYST, index - 1), \ + SENSOR_ATTR_2(temp##index##_warn, S_IRUGO | S_IWUSR, show_temp, \ + store_temp, TEMP_WARN, index - 1), \ + SENSOR_ATTR_2(temp##index##_warn_hyst, S_IRUGO | S_IWUSR, \ + show_temp, store_temp, TEMP_WARN_HYST, index - 1), \ + SENSOR_ATTR_2(temp##index##_alarm, S_IRUGO, \ + show_alarm_beep, NULL, ALARM_STATUS, index + 11), \ + SENSOR_ATTR_2(temp##index##_beep, S_IWUSR | S_IRUGO, \ + show_alarm_beep, store_beep, BEEP_ENABLE, index + 11), \ + SENSOR_ATTR_2(temp##index##_auto_channels_pwm, \ + S_IRUGO | S_IWUSR, show_sf_ctrl, store_sf_ctrl, \ + TEMP_FAN_MAP, index - 1), \ + SENSOR_ATTR_2(temp##index##_pwm_enable, S_IWUSR | S_IRUGO, \ + show_sf_ctrl, store_sf_ctrl, TEMP_PWM_ENABLE, \ + index - 1), \ + SENSOR_ATTR_2(thermal_cruise##index, S_IRUGO | S_IWUSR, \ + show_sf_ctrl, store_sf_ctrl, TEMP_CRUISE, index - 1), \ + SENSOR_ATTR_2(tolerance##index, S_IRUGO | S_IWUSR, show_sf_ctrl,\ + store_sf_ctrl, TEMP_TOLERANCE, index - 1), \ + SENSOR_ATTR_2(temp##index##_auto_point1_pwm, S_IRUGO | S_IWUSR, \ + show_sf2_pwm, store_sf2_pwm, 0, index - 1), \ + SENSOR_ATTR_2(temp##index##_auto_point2_pwm, S_IRUGO | S_IWUSR, \ + show_sf2_pwm, store_sf2_pwm, 1, index - 1), \ + SENSOR_ATTR_2(temp##index##_auto_point3_pwm, S_IRUGO | S_IWUSR, \ + show_sf2_pwm, store_sf2_pwm, 2, index - 1), \ + SENSOR_ATTR_2(temp##index##_auto_point4_pwm, S_IRUGO | S_IWUSR, \ + show_sf2_pwm, store_sf2_pwm, 3, index - 1), \ + SENSOR_ATTR_2(temp##index##_auto_point5_pwm, S_IRUGO | S_IWUSR, \ + show_sf2_pwm, store_sf2_pwm, 4, index - 1), \ + SENSOR_ATTR_2(temp##index##_auto_point6_pwm, S_IRUGO | S_IWUSR, \ + show_sf2_pwm, store_sf2_pwm, 5, index - 1), \ + SENSOR_ATTR_2(temp##index##_auto_point7_pwm, S_IRUGO | S_IWUSR, \ + show_sf2_pwm, store_sf2_pwm, 6, index - 1), \ + SENSOR_ATTR_2(temp##index##_auto_point1_temp, S_IRUGO | S_IWUSR,\ + show_sf2_temp, store_sf2_temp, 0, index - 1), \ + SENSOR_ATTR_2(temp##index##_auto_point2_temp, S_IRUGO | S_IWUSR,\ + show_sf2_temp, store_sf2_temp, 1, index - 1), \ + SENSOR_ATTR_2(temp##index##_auto_point3_temp, S_IRUGO | S_IWUSR,\ + show_sf2_temp, store_sf2_temp, 2, index - 1), \ + SENSOR_ATTR_2(temp##index##_auto_point4_temp, S_IRUGO | S_IWUSR,\ + show_sf2_temp, store_sf2_temp, 3, index - 1), \ + SENSOR_ATTR_2(temp##index##_auto_point5_temp, S_IRUGO | S_IWUSR,\ + show_sf2_temp, store_sf2_temp, 4, index - 1), \ + SENSOR_ATTR_2(temp##index##_auto_point6_temp, S_IRUGO | S_IWUSR,\ + show_sf2_temp, store_sf2_temp, 5, index - 1), \ + SENSOR_ATTR_2(temp##index##_auto_point7_temp, S_IRUGO | S_IWUSR,\ + show_sf2_temp, store_sf2_temp, 6, index - 1) + +static struct sensor_device_attribute_2 w83793_sensor_attr_2[] = { + SENSOR_ATTR_IN(0), + SENSOR_ATTR_IN(1), + SENSOR_ATTR_IN(2), + SENSOR_ATTR_IN(3), + SENSOR_ATTR_IN(4), + SENSOR_ATTR_IN(5), + SENSOR_ATTR_IN(6), + SENSOR_ATTR_IN(7), + SENSOR_ATTR_IN(8), + SENSOR_ATTR_IN(9), + SENSOR_ATTR_FAN(1), + SENSOR_ATTR_FAN(2), + SENSOR_ATTR_FAN(3), + SENSOR_ATTR_FAN(4), + SENSOR_ATTR_FAN(5), + SENSOR_ATTR_PWM(1), + SENSOR_ATTR_PWM(2), + SENSOR_ATTR_PWM(3), +}; + +static struct sensor_device_attribute_2 w83793_temp[] = { + SENSOR_ATTR_TEMP(1), + SENSOR_ATTR_TEMP(2), + SENSOR_ATTR_TEMP(3), + SENSOR_ATTR_TEMP(4), + SENSOR_ATTR_TEMP(5), + SENSOR_ATTR_TEMP(6), +}; + +/* Fan6-Fan12 */ +static struct sensor_device_attribute_2 w83793_left_fan[] = { + SENSOR_ATTR_FAN(6), + SENSOR_ATTR_FAN(7), + SENSOR_ATTR_FAN(8), + SENSOR_ATTR_FAN(9), + SENSOR_ATTR_FAN(10), + SENSOR_ATTR_FAN(11), + SENSOR_ATTR_FAN(12), +}; + +/* Pwm4-Pwm8 */ +static struct sensor_device_attribute_2 w83793_left_pwm[] = { + SENSOR_ATTR_PWM(4), + SENSOR_ATTR_PWM(5), + SENSOR_ATTR_PWM(6), + SENSOR_ATTR_PWM(7), + SENSOR_ATTR_PWM(8), +}; + +static struct sensor_device_attribute_2 w83793_vid[] = { + SENSOR_ATTR_2(cpu0_vid, S_IRUGO, show_vid, NULL, NOT_USED, 0), + SENSOR_ATTR_2(cpu1_vid, S_IRUGO, show_vid, NULL, NOT_USED, 1), +}; +static DEVICE_ATTR_RW(vrm); + +static struct sensor_device_attribute_2 sda_single_files[] = { + SENSOR_ATTR_2(intrusion0_alarm, S_IWUSR | S_IRUGO, show_alarm_beep, + store_chassis_clear, ALARM_STATUS, 30), + SENSOR_ATTR_2(beep_enable, S_IWUSR | S_IRUGO, show_beep_enable, + store_beep_enable, NOT_USED, NOT_USED), + SENSOR_ATTR_2(pwm_default, S_IWUSR | S_IRUGO, show_sf_setup, + store_sf_setup, SETUP_PWM_DEFAULT, NOT_USED), + SENSOR_ATTR_2(pwm_uptime, S_IWUSR | S_IRUGO, show_sf_setup, + store_sf_setup, SETUP_PWM_UPTIME, NOT_USED), + SENSOR_ATTR_2(pwm_downtime, S_IWUSR | S_IRUGO, show_sf_setup, + store_sf_setup, SETUP_PWM_DOWNTIME, NOT_USED), + SENSOR_ATTR_2(temp_critical, S_IWUSR | S_IRUGO, show_sf_setup, + store_sf_setup, SETUP_TEMP_CRITICAL, NOT_USED), +}; + +static void w83793_init_client(struct i2c_client *client) +{ + if (reset) + w83793_write_value(client, W83793_REG_CONFIG, 0x80); + + /* Start monitoring */ + w83793_write_value(client, W83793_REG_CONFIG, + w83793_read_value(client, W83793_REG_CONFIG) | 0x01); +} + +/* + * Watchdog routines + */ + +static int watchdog_set_timeout(struct w83793_data *data, int timeout) +{ + unsigned int mtimeout; + int ret; + + mtimeout = DIV_ROUND_UP(timeout, 60); + + if (mtimeout > 255) + return -EINVAL; + + mutex_lock(&data->watchdog_lock); + if (!data->client) { + ret = -ENODEV; + goto leave; + } + + data->watchdog_timeout = mtimeout; + + /* Set Timeout value (in Minutes) */ + w83793_write_value(data->client, W83793_REG_WDT_TIMEOUT, + data->watchdog_timeout); + + ret = mtimeout * 60; + +leave: + mutex_unlock(&data->watchdog_lock); + return ret; +} + +static int watchdog_get_timeout(struct w83793_data *data) +{ + int timeout; + + mutex_lock(&data->watchdog_lock); + timeout = data->watchdog_timeout * 60; + mutex_unlock(&data->watchdog_lock); + + return timeout; +} + +static int watchdog_trigger(struct w83793_data *data) +{ + int ret = 0; + + mutex_lock(&data->watchdog_lock); + if (!data->client) { + ret = -ENODEV; + goto leave; + } + + /* Set Timeout value (in Minutes) */ + w83793_write_value(data->client, W83793_REG_WDT_TIMEOUT, + data->watchdog_timeout); + +leave: + mutex_unlock(&data->watchdog_lock); + return ret; +} + +static int watchdog_enable(struct w83793_data *data) +{ + int ret = 0; + + mutex_lock(&data->watchdog_lock); + if (!data->client) { + ret = -ENODEV; + goto leave; + } + + /* Set initial timeout */ + w83793_write_value(data->client, W83793_REG_WDT_TIMEOUT, + data->watchdog_timeout); + + /* Enable Soft Watchdog */ + w83793_write_value(data->client, W83793_REG_WDT_LOCK, 0x55); + +leave: + mutex_unlock(&data->watchdog_lock); + return ret; +} + +static int watchdog_disable(struct w83793_data *data) +{ + int ret = 0; + + mutex_lock(&data->watchdog_lock); + if (!data->client) { + ret = -ENODEV; + goto leave; + } + + /* Disable Soft Watchdog */ + w83793_write_value(data->client, W83793_REG_WDT_LOCK, 0xAA); + +leave: + mutex_unlock(&data->watchdog_lock); + return ret; +} + +static int watchdog_open(struct inode *inode, struct file *filp) +{ + struct w83793_data *pos, *data = NULL; + int watchdog_is_open; + + /* + * We get called from drivers/char/misc.c with misc_mtx hold, and we + * call misc_register() from w83793_probe() with watchdog_data_mutex + * hold, as misc_register() takes the misc_mtx lock, this is a possible + * deadlock, so we use mutex_trylock here. + */ + if (!mutex_trylock(&watchdog_data_mutex)) + return -ERESTARTSYS; + list_for_each_entry(pos, &watchdog_data_list, list) { + if (pos->watchdog_miscdev.minor == iminor(inode)) { + data = pos; + break; + } + } + + /* Check, if device is already open */ + watchdog_is_open = test_and_set_bit(0, &data->watchdog_is_open); + + /* + * Increase data reference counter (if not already done). + * Note we can never not have found data, so we don't check for this + */ + if (!watchdog_is_open) + kref_get(&data->kref); + + mutex_unlock(&watchdog_data_mutex); + + /* Check, if device is already open and possibly issue error */ + if (watchdog_is_open) + return -EBUSY; + + /* Enable Soft Watchdog */ + watchdog_enable(data); + + /* Store pointer to data into filp's private data */ + filp->private_data = data; + + return stream_open(inode, filp); +} + +static int watchdog_close(struct inode *inode, struct file *filp) +{ + struct w83793_data *data = filp->private_data; + + if (data->watchdog_expect_close) { + watchdog_disable(data); + data->watchdog_expect_close = 0; + } else { + watchdog_trigger(data); + dev_crit(&data->client->dev, + "unexpected close, not stopping watchdog!\n"); + } + + clear_bit(0, &data->watchdog_is_open); + + /* Decrease data reference counter */ + mutex_lock(&watchdog_data_mutex); + kref_put(&data->kref, w83793_release_resources); + mutex_unlock(&watchdog_data_mutex); + + return 0; +} + +static ssize_t watchdog_write(struct file *filp, const char __user *buf, + size_t count, loff_t *offset) +{ + ssize_t ret; + struct w83793_data *data = filp->private_data; + + if (count) { + if (!nowayout) { + size_t i; + + /* Clear it in case it was set with a previous write */ + data->watchdog_expect_close = 0; + + for (i = 0; i != count; i++) { + char c; + if (get_user(c, buf + i)) + return -EFAULT; + if (c == 'V') + data->watchdog_expect_close = 1; + } + } + ret = watchdog_trigger(data); + if (ret < 0) + return ret; + } + return count; +} + +static long watchdog_ioctl(struct file *filp, unsigned int cmd, + unsigned long arg) +{ + struct watchdog_info ident = { + .options = WDIOF_KEEPALIVEPING | + WDIOF_SETTIMEOUT | + WDIOF_CARDRESET, + .identity = "w83793 watchdog" + }; + + int val, ret = 0; + struct w83793_data *data = filp->private_data; + + switch (cmd) { + case WDIOC_GETSUPPORT: + if (!nowayout) + ident.options |= WDIOF_MAGICCLOSE; + if (copy_to_user((void __user *)arg, &ident, sizeof(ident))) + ret = -EFAULT; + break; + + case WDIOC_GETSTATUS: + val = data->watchdog_caused_reboot ? WDIOF_CARDRESET : 0; + ret = put_user(val, (int __user *)arg); + break; + + case WDIOC_GETBOOTSTATUS: + ret = put_user(0, (int __user *)arg); + break; + + case WDIOC_KEEPALIVE: + ret = watchdog_trigger(data); + break; + + case WDIOC_GETTIMEOUT: + val = watchdog_get_timeout(data); + ret = put_user(val, (int __user *)arg); + break; + + case WDIOC_SETTIMEOUT: + if (get_user(val, (int __user *)arg)) { + ret = -EFAULT; + break; + } + ret = watchdog_set_timeout(data, val); + if (ret > 0) + ret = put_user(ret, (int __user *)arg); + break; + + case WDIOC_SETOPTIONS: + if (get_user(val, (int __user *)arg)) { + ret = -EFAULT; + break; + } + + if (val & WDIOS_DISABLECARD) + ret = watchdog_disable(data); + else if (val & WDIOS_ENABLECARD) + ret = watchdog_enable(data); + else + ret = -EINVAL; + + break; + default: + ret = -ENOTTY; + } + return ret; +} + +static const struct file_operations watchdog_fops = { + .owner = THIS_MODULE, + .llseek = no_llseek, + .open = watchdog_open, + .release = watchdog_close, + .write = watchdog_write, + .unlocked_ioctl = watchdog_ioctl, + .compat_ioctl = compat_ptr_ioctl, +}; + +/* + * Notifier for system down + */ + +static int watchdog_notify_sys(struct notifier_block *this, unsigned long code, + void *unused) +{ + struct w83793_data *data = NULL; + + if (code == SYS_DOWN || code == SYS_HALT) { + + /* Disable each registered watchdog */ + mutex_lock(&watchdog_data_mutex); + list_for_each_entry(data, &watchdog_data_list, list) { + if (data->watchdog_miscdev.minor) + watchdog_disable(data); + } + mutex_unlock(&watchdog_data_mutex); + } + + return NOTIFY_DONE; +} + +/* + * The WDT needs to learn about soft shutdowns in order to + * turn the timebomb registers off. + */ + +static struct notifier_block watchdog_notifier = { + .notifier_call = watchdog_notify_sys, +}; + +/* + * Init / remove routines + */ + +static void w83793_remove(struct i2c_client *client) +{ + struct w83793_data *data = i2c_get_clientdata(client); + struct device *dev = &client->dev; + int i, tmp; + + /* Unregister the watchdog (if registered) */ + if (data->watchdog_miscdev.minor) { + misc_deregister(&data->watchdog_miscdev); + + if (data->watchdog_is_open) { + dev_warn(&client->dev, + "i2c client detached with watchdog open! " + "Stopping watchdog.\n"); + watchdog_disable(data); + } + + mutex_lock(&watchdog_data_mutex); + list_del(&data->list); + mutex_unlock(&watchdog_data_mutex); + + /* Tell the watchdog code the client is gone */ + mutex_lock(&data->watchdog_lock); + data->client = NULL; + mutex_unlock(&data->watchdog_lock); + } + + /* Reset Configuration Register to Disable Watch Dog Registers */ + tmp = w83793_read_value(client, W83793_REG_CONFIG); + w83793_write_value(client, W83793_REG_CONFIG, tmp & ~0x04); + + unregister_reboot_notifier(&watchdog_notifier); + + hwmon_device_unregister(data->hwmon_dev); + + for (i = 0; i < ARRAY_SIZE(w83793_sensor_attr_2); i++) + device_remove_file(dev, + &w83793_sensor_attr_2[i].dev_attr); + + for (i = 0; i < ARRAY_SIZE(sda_single_files); i++) + device_remove_file(dev, &sda_single_files[i].dev_attr); + + for (i = 0; i < ARRAY_SIZE(w83793_vid); i++) + device_remove_file(dev, &w83793_vid[i].dev_attr); + device_remove_file(dev, &dev_attr_vrm); + + for (i = 0; i < ARRAY_SIZE(w83793_left_fan); i++) + device_remove_file(dev, &w83793_left_fan[i].dev_attr); + + for (i = 0; i < ARRAY_SIZE(w83793_left_pwm); i++) + device_remove_file(dev, &w83793_left_pwm[i].dev_attr); + + for (i = 0; i < ARRAY_SIZE(w83793_temp); i++) + device_remove_file(dev, &w83793_temp[i].dev_attr); + + /* Decrease data reference counter */ + mutex_lock(&watchdog_data_mutex); + kref_put(&data->kref, w83793_release_resources); + mutex_unlock(&watchdog_data_mutex); +} + +static int +w83793_detect_subclients(struct i2c_client *client) +{ + int i, id; + int address = client->addr; + u8 tmp; + struct i2c_adapter *adapter = client->adapter; + + id = i2c_adapter_id(adapter); + if (force_subclients[0] == id && force_subclients[1] == address) { + for (i = 2; i <= 3; i++) { + if (force_subclients[i] < 0x48 + || force_subclients[i] > 0x4f) { + dev_err(&client->dev, + "invalid subclient " + "address %d; must be 0x48-0x4f\n", + force_subclients[i]); + return -EINVAL; + } + } + w83793_write_value(client, W83793_REG_I2C_SUBADDR, + (force_subclients[2] & 0x07) | + ((force_subclients[3] & 0x07) << 4)); + } + + tmp = w83793_read_value(client, W83793_REG_I2C_SUBADDR); + + if (!(tmp & 0x88) && (tmp & 0x7) == ((tmp >> 4) & 0x7)) { + dev_err(&client->dev, + "duplicate addresses 0x%x, use force_subclient\n", 0x48 + (tmp & 0x7)); + return -ENODEV; + } + + if (!(tmp & 0x08)) + devm_i2c_new_dummy_device(&client->dev, adapter, 0x48 + (tmp & 0x7)); + + if (!(tmp & 0x80)) + devm_i2c_new_dummy_device(&client->dev, adapter, 0x48 + ((tmp >> 4) & 0x7)); + + return 0; +} + +/* Return 0 if detection is successful, -ENODEV otherwise */ +static int w83793_detect(struct i2c_client *client, + struct i2c_board_info *info) +{ + u8 tmp, bank, chip_id; + struct i2c_adapter *adapter = client->adapter; + unsigned short address = client->addr; + + if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) + return -ENODEV; + + bank = i2c_smbus_read_byte_data(client, W83793_REG_BANKSEL); + + tmp = bank & 0x80 ? 0x5c : 0xa3; + /* Check Winbond vendor ID */ + if (tmp != i2c_smbus_read_byte_data(client, W83793_REG_VENDORID)) { + pr_debug("w83793: Detection failed at check vendor id\n"); + return -ENODEV; + } + + /* + * If Winbond chip, address of chip and W83793_REG_I2C_ADDR + * should match + */ + if ((bank & 0x07) == 0 + && i2c_smbus_read_byte_data(client, W83793_REG_I2C_ADDR) != + (address << 1)) { + pr_debug("w83793: Detection failed at check i2c addr\n"); + return -ENODEV; + } + + /* Determine the chip type now */ + chip_id = i2c_smbus_read_byte_data(client, W83793_REG_CHIPID); + if (chip_id != 0x7b) + return -ENODEV; + + strscpy(info->type, "w83793", I2C_NAME_SIZE); + + return 0; +} + +static int w83793_probe(struct i2c_client *client) +{ + struct device *dev = &client->dev; + static const int watchdog_minors[] = { + WATCHDOG_MINOR, 212, 213, 214, 215 + }; + struct w83793_data *data; + int i, tmp, val, err; + int files_fan = ARRAY_SIZE(w83793_left_fan) / 7; + int files_pwm = ARRAY_SIZE(w83793_left_pwm) / 5; + int files_temp = ARRAY_SIZE(w83793_temp) / 6; + + data = kzalloc(sizeof(struct w83793_data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + i2c_set_clientdata(client, data); + data->bank = i2c_smbus_read_byte_data(client, W83793_REG_BANKSEL); + mutex_init(&data->update_lock); + mutex_init(&data->watchdog_lock); + INIT_LIST_HEAD(&data->list); + kref_init(&data->kref); + + /* + * Store client pointer in our data struct for watchdog usage + * (where the client is found through a data ptr instead of the + * otherway around) + */ + data->client = client; + + err = w83793_detect_subclients(client); + if (err) + goto free_mem; + + /* Initialize the chip */ + w83793_init_client(client); + + /* + * Only fan 1-5 has their own input pins, + * Pwm 1-3 has their own pins + */ + data->has_fan = 0x1f; + data->has_pwm = 0x07; + tmp = w83793_read_value(client, W83793_REG_MFC); + val = w83793_read_value(client, W83793_REG_FANIN_CTRL); + + /* check the function of pins 49-56 */ + if (tmp & 0x80) { + data->has_vid |= 0x2; /* has VIDB */ + } else { + data->has_pwm |= 0x18; /* pwm 4,5 */ + if (val & 0x01) { /* fan 6 */ + data->has_fan |= 0x20; + data->has_pwm |= 0x20; + } + if (val & 0x02) { /* fan 7 */ + data->has_fan |= 0x40; + data->has_pwm |= 0x40; + } + if (!(tmp & 0x40) && (val & 0x04)) { /* fan 8 */ + data->has_fan |= 0x80; + data->has_pwm |= 0x80; + } + } + + /* check the function of pins 37-40 */ + if (!(tmp & 0x29)) + data->has_vid |= 0x1; /* has VIDA */ + if (0x08 == (tmp & 0x0c)) { + if (val & 0x08) /* fan 9 */ + data->has_fan |= 0x100; + if (val & 0x10) /* fan 10 */ + data->has_fan |= 0x200; + } + if (0x20 == (tmp & 0x30)) { + if (val & 0x20) /* fan 11 */ + data->has_fan |= 0x400; + if (val & 0x40) /* fan 12 */ + data->has_fan |= 0x800; + } + + if ((tmp & 0x01) && (val & 0x04)) { /* fan 8, second location */ + data->has_fan |= 0x80; + data->has_pwm |= 0x80; + } + + tmp = w83793_read_value(client, W83793_REG_FANIN_SEL); + if ((tmp & 0x01) && (val & 0x08)) { /* fan 9, second location */ + data->has_fan |= 0x100; + } + if ((tmp & 0x02) && (val & 0x10)) { /* fan 10, second location */ + data->has_fan |= 0x200; + } + if ((tmp & 0x04) && (val & 0x20)) { /* fan 11, second location */ + data->has_fan |= 0x400; + } + if ((tmp & 0x08) && (val & 0x40)) { /* fan 12, second location */ + data->has_fan |= 0x800; + } + + /* check the temp1-6 mode, ignore former AMDSI selected inputs */ + tmp = w83793_read_value(client, W83793_REG_TEMP_MODE[0]); + if (tmp & 0x01) + data->has_temp |= 0x01; + if (tmp & 0x04) + data->has_temp |= 0x02; + if (tmp & 0x10) + data->has_temp |= 0x04; + if (tmp & 0x40) + data->has_temp |= 0x08; + + tmp = w83793_read_value(client, W83793_REG_TEMP_MODE[1]); + if (tmp & 0x01) + data->has_temp |= 0x10; + if (tmp & 0x02) + data->has_temp |= 0x20; + + /* Register sysfs hooks */ + for (i = 0; i < ARRAY_SIZE(w83793_sensor_attr_2); i++) { + err = device_create_file(dev, + &w83793_sensor_attr_2[i].dev_attr); + if (err) + goto exit_remove; + } + + for (i = 0; i < ARRAY_SIZE(w83793_vid); i++) { + if (!(data->has_vid & (1 << i))) + continue; + err = device_create_file(dev, &w83793_vid[i].dev_attr); + if (err) + goto exit_remove; + } + if (data->has_vid) { + data->vrm = vid_which_vrm(); + err = device_create_file(dev, &dev_attr_vrm); + if (err) + goto exit_remove; + } + + for (i = 0; i < ARRAY_SIZE(sda_single_files); i++) { + err = device_create_file(dev, &sda_single_files[i].dev_attr); + if (err) + goto exit_remove; + + } + + for (i = 0; i < 6; i++) { + int j; + if (!(data->has_temp & (1 << i))) + continue; + for (j = 0; j < files_temp; j++) { + err = device_create_file(dev, + &w83793_temp[(i) * files_temp + + j].dev_attr); + if (err) + goto exit_remove; + } + } + + for (i = 5; i < 12; i++) { + int j; + if (!(data->has_fan & (1 << i))) + continue; + for (j = 0; j < files_fan; j++) { + err = device_create_file(dev, + &w83793_left_fan[(i - 5) * files_fan + + j].dev_attr); + if (err) + goto exit_remove; + } + } + + for (i = 3; i < 8; i++) { + int j; + if (!(data->has_pwm & (1 << i))) + continue; + for (j = 0; j < files_pwm; j++) { + err = device_create_file(dev, + &w83793_left_pwm[(i - 3) * files_pwm + + j].dev_attr); + if (err) + goto exit_remove; + } + } + + data->hwmon_dev = hwmon_device_register(dev); + if (IS_ERR(data->hwmon_dev)) { + err = PTR_ERR(data->hwmon_dev); + goto exit_remove; + } + + /* Watchdog initialization */ + + /* Register boot notifier */ + err = register_reboot_notifier(&watchdog_notifier); + if (err != 0) { + dev_err(&client->dev, + "cannot register reboot notifier (err=%d)\n", err); + goto exit_devunreg; + } + + /* + * Enable Watchdog registers. + * Set Configuration Register to Enable Watch Dog Registers + * (Bit 2) = XXXX, X1XX. + */ + tmp = w83793_read_value(client, W83793_REG_CONFIG); + w83793_write_value(client, W83793_REG_CONFIG, tmp | 0x04); + + /* Set the default watchdog timeout */ + data->watchdog_timeout = timeout; + + /* Check, if last reboot was caused by watchdog */ + data->watchdog_caused_reboot = + w83793_read_value(data->client, W83793_REG_WDT_STATUS) & 0x01; + + /* Disable Soft Watchdog during initialiation */ + watchdog_disable(data); + + /* + * We take the data_mutex lock early so that watchdog_open() cannot + * run when misc_register() has completed, but we've not yet added + * our data to the watchdog_data_list (and set the default timeout) + */ + mutex_lock(&watchdog_data_mutex); + for (i = 0; i < ARRAY_SIZE(watchdog_minors); i++) { + /* Register our watchdog part */ + snprintf(data->watchdog_name, sizeof(data->watchdog_name), + "watchdog%c", (i == 0) ? '\0' : ('0' + i)); + data->watchdog_miscdev.name = data->watchdog_name; + data->watchdog_miscdev.fops = &watchdog_fops; + data->watchdog_miscdev.minor = watchdog_minors[i]; + + err = misc_register(&data->watchdog_miscdev); + if (err == -EBUSY) + continue; + if (err) { + data->watchdog_miscdev.minor = 0; + dev_err(&client->dev, + "Registering watchdog chardev: %d\n", err); + break; + } + + list_add(&data->list, &watchdog_data_list); + + dev_info(&client->dev, + "Registered watchdog chardev major 10, minor: %d\n", + watchdog_minors[i]); + break; + } + if (i == ARRAY_SIZE(watchdog_minors)) { + data->watchdog_miscdev.minor = 0; + dev_warn(&client->dev, + "Couldn't register watchdog chardev (due to no free minor)\n"); + } + + mutex_unlock(&watchdog_data_mutex); + + return 0; + + /* Unregister hwmon device */ + +exit_devunreg: + + hwmon_device_unregister(data->hwmon_dev); + + /* Unregister sysfs hooks */ + +exit_remove: + for (i = 0; i < ARRAY_SIZE(w83793_sensor_attr_2); i++) + device_remove_file(dev, &w83793_sensor_attr_2[i].dev_attr); + + for (i = 0; i < ARRAY_SIZE(sda_single_files); i++) + device_remove_file(dev, &sda_single_files[i].dev_attr); + + for (i = 0; i < ARRAY_SIZE(w83793_vid); i++) + device_remove_file(dev, &w83793_vid[i].dev_attr); + + for (i = 0; i < ARRAY_SIZE(w83793_left_fan); i++) + device_remove_file(dev, &w83793_left_fan[i].dev_attr); + + for (i = 0; i < ARRAY_SIZE(w83793_left_pwm); i++) + device_remove_file(dev, &w83793_left_pwm[i].dev_attr); + + for (i = 0; i < ARRAY_SIZE(w83793_temp); i++) + device_remove_file(dev, &w83793_temp[i].dev_attr); +free_mem: + kfree(data); +exit: + return err; +} + +static void w83793_update_nonvolatile(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct w83793_data *data = i2c_get_clientdata(client); + int i, j; + /* + * They are somewhat "stable" registers, and to update them every time + * takes so much time, it's just not worthy. Update them in a long + * interval to avoid exception. + */ + if (!(time_after(jiffies, data->last_nonvolatile + HZ * 300) + || !data->valid)) + return; + /* update voltage limits */ + for (i = 1; i < 3; i++) { + for (j = 0; j < ARRAY_SIZE(data->in); j++) { + data->in[j][i] = + w83793_read_value(client, W83793_REG_IN[j][i]); + } + data->in_low_bits[i] = + w83793_read_value(client, W83793_REG_IN_LOW_BITS[i]); + } + + for (i = 0; i < ARRAY_SIZE(data->fan_min); i++) { + /* Update the Fan measured value and limits */ + if (!(data->has_fan & (1 << i))) + continue; + data->fan_min[i] = + w83793_read_value(client, W83793_REG_FAN_MIN(i)) << 8; + data->fan_min[i] |= + w83793_read_value(client, W83793_REG_FAN_MIN(i) + 1); + } + + for (i = 0; i < ARRAY_SIZE(data->temp_fan_map); i++) { + if (!(data->has_temp & (1 << i))) + continue; + data->temp_fan_map[i] = + w83793_read_value(client, W83793_REG_TEMP_FAN_MAP(i)); + for (j = 1; j < 5; j++) { + data->temp[i][j] = + w83793_read_value(client, W83793_REG_TEMP[i][j]); + } + data->temp_cruise[i] = + w83793_read_value(client, W83793_REG_TEMP_CRUISE(i)); + for (j = 0; j < 7; j++) { + data->sf2_pwm[i][j] = + w83793_read_value(client, W83793_REG_SF2_PWM(i, j)); + data->sf2_temp[i][j] = + w83793_read_value(client, + W83793_REG_SF2_TEMP(i, j)); + } + } + + for (i = 0; i < ARRAY_SIZE(data->temp_mode); i++) + data->temp_mode[i] = + w83793_read_value(client, W83793_REG_TEMP_MODE[i]); + + for (i = 0; i < ARRAY_SIZE(data->tolerance); i++) { + data->tolerance[i] = + w83793_read_value(client, W83793_REG_TEMP_TOL(i)); + } + + for (i = 0; i < ARRAY_SIZE(data->pwm); i++) { + if (!(data->has_pwm & (1 << i))) + continue; + data->pwm[i][PWM_NONSTOP] = + w83793_read_value(client, W83793_REG_PWM(i, PWM_NONSTOP)); + data->pwm[i][PWM_START] = + w83793_read_value(client, W83793_REG_PWM(i, PWM_START)); + data->pwm_stop_time[i] = + w83793_read_value(client, W83793_REG_PWM_STOP_TIME(i)); + } + + data->pwm_default = w83793_read_value(client, W83793_REG_PWM_DEFAULT); + data->pwm_enable = w83793_read_value(client, W83793_REG_PWM_ENABLE); + data->pwm_uptime = w83793_read_value(client, W83793_REG_PWM_UPTIME); + data->pwm_downtime = w83793_read_value(client, W83793_REG_PWM_DOWNTIME); + data->temp_critical = + w83793_read_value(client, W83793_REG_TEMP_CRITICAL); + data->beep_enable = w83793_read_value(client, W83793_REG_OVT_BEEP); + + for (i = 0; i < ARRAY_SIZE(data->beeps); i++) + data->beeps[i] = w83793_read_value(client, W83793_REG_BEEP(i)); + + data->last_nonvolatile = jiffies; +} + +static struct w83793_data *w83793_update_device(struct device *dev) +{ + struct i2c_client *client = to_i2c_client(dev); + struct w83793_data *data = i2c_get_clientdata(client); + int i; + + mutex_lock(&data->update_lock); + + if (!(time_after(jiffies, data->last_updated + HZ * 2) + || !data->valid)) + goto END; + + /* Update the voltages measured value and limits */ + for (i = 0; i < ARRAY_SIZE(data->in); i++) + data->in[i][IN_READ] = + w83793_read_value(client, W83793_REG_IN[i][IN_READ]); + + data->in_low_bits[IN_READ] = + w83793_read_value(client, W83793_REG_IN_LOW_BITS[IN_READ]); + + for (i = 0; i < ARRAY_SIZE(data->fan); i++) { + if (!(data->has_fan & (1 << i))) + continue; + data->fan[i] = + w83793_read_value(client, W83793_REG_FAN(i)) << 8; + data->fan[i] |= + w83793_read_value(client, W83793_REG_FAN(i) + 1); + } + + for (i = 0; i < ARRAY_SIZE(data->temp); i++) { + if (!(data->has_temp & (1 << i))) + continue; + data->temp[i][TEMP_READ] = + w83793_read_value(client, W83793_REG_TEMP[i][TEMP_READ]); + } + + data->temp_low_bits = + w83793_read_value(client, W83793_REG_TEMP_LOW_BITS); + + for (i = 0; i < ARRAY_SIZE(data->pwm); i++) { + if (data->has_pwm & (1 << i)) + data->pwm[i][PWM_DUTY] = + w83793_read_value(client, + W83793_REG_PWM(i, PWM_DUTY)); + } + + for (i = 0; i < ARRAY_SIZE(data->alarms); i++) + data->alarms[i] = + w83793_read_value(client, W83793_REG_ALARM(i)); + if (data->has_vid & 0x01) + data->vid[0] = w83793_read_value(client, W83793_REG_VID_INA); + if (data->has_vid & 0x02) + data->vid[1] = w83793_read_value(client, W83793_REG_VID_INB); + w83793_update_nonvolatile(dev); + data->last_updated = jiffies; + data->valid = true; + +END: + mutex_unlock(&data->update_lock); + return data; +} + +/* + * Ignore the possibility that somebody change bank outside the driver + * Must be called with data->update_lock held, except during initialization + */ +static u8 w83793_read_value(struct i2c_client *client, u16 reg) +{ + struct w83793_data *data = i2c_get_clientdata(client); + u8 res; + u8 new_bank = reg >> 8; + + new_bank |= data->bank & 0xfc; + if (data->bank != new_bank) { + if (i2c_smbus_write_byte_data + (client, W83793_REG_BANKSEL, new_bank) >= 0) + data->bank = new_bank; + else { + dev_err(&client->dev, + "set bank to %d failed, fall back " + "to bank %d, read reg 0x%x error\n", + new_bank, data->bank, reg); + res = 0x0; /* read 0x0 from the chip */ + goto END; + } + } + res = i2c_smbus_read_byte_data(client, reg & 0xff); +END: + return res; +} + +/* Must be called with data->update_lock held, except during initialization */ +static int w83793_write_value(struct i2c_client *client, u16 reg, u8 value) +{ + struct w83793_data *data = i2c_get_clientdata(client); + int res; + u8 new_bank = reg >> 8; + + new_bank |= data->bank & 0xfc; + if (data->bank != new_bank) { + res = i2c_smbus_write_byte_data(client, W83793_REG_BANKSEL, + new_bank); + if (res < 0) { + dev_err(&client->dev, + "set bank to %d failed, fall back " + "to bank %d, write reg 0x%x error\n", + new_bank, data->bank, reg); + goto END; + } + data->bank = new_bank; + } + + res = i2c_smbus_write_byte_data(client, reg & 0xff, value); +END: + return res; +} + +module_i2c_driver(w83793_driver); + +MODULE_AUTHOR("Yuan Mu, Sven Anders"); +MODULE_DESCRIPTION("w83793 driver"); +MODULE_LICENSE("GPL"); |