diff options
Diffstat (limited to 'drivers/i2c/busses/i2c-iop3xx.h')
| -rw-r--r-- | drivers/i2c/busses/i2c-iop3xx.h | 99 |
1 files changed, 99 insertions, 0 deletions
diff --git a/drivers/i2c/busses/i2c-iop3xx.h b/drivers/i2c/busses/i2c-iop3xx.h new file mode 100644 index 000000000..143548335 --- /dev/null +++ b/drivers/i2c/busses/i2c-iop3xx.h @@ -0,0 +1,99 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* ------------------------------------------------------------------------- */ +/* i2c-iop3xx.h algorithm driver definitions private to i2c-iop3xx.c */ +/* ------------------------------------------------------------------------- */ +/* Copyright (C) 2003 Peter Milne, D-TACQ Solutions Ltd + * <Peter dot Milne at D hyphen TACQ dot com> + + */ +/* ------------------------------------------------------------------------- */ + + +#ifndef I2C_IOP3XX_H +#define I2C_IOP3XX_H 1 + +/* + * iop321 hardware bit definitions + */ +#define IOP3XX_ICR_FAST_MODE 0x8000 /* 1=400kBps, 0=100kBps */ +#define IOP3XX_ICR_UNIT_RESET 0x4000 /* 1=RESET */ +#define IOP3XX_ICR_SAD_IE 0x2000 /* 1=Slave Detect Interrupt Enable */ +#define IOP3XX_ICR_ALD_IE 0x1000 /* 1=Arb Loss Detect Interrupt Enable */ +#define IOP3XX_ICR_SSD_IE 0x0800 /* 1=Slave STOP Detect Interrupt Enable */ +#define IOP3XX_ICR_BERR_IE 0x0400 /* 1=Bus Error Interrupt Enable */ +#define IOP3XX_ICR_RXFULL_IE 0x0200 /* 1=Receive Full Interrupt Enable */ +#define IOP3XX_ICR_TXEMPTY_IE 0x0100 /* 1=Transmit Empty Interrupt Enable */ +#define IOP3XX_ICR_GCD 0x0080 /* 1=General Call Disable */ +/* + * IOP3XX_ICR_GCD: 1 disables response as slave. "This bit must be set + * when sending a master mode general call message from the I2C unit" + */ +#define IOP3XX_ICR_UE 0x0040 /* 1=Unit Enable */ +/* + * "NOTE: To avoid I2C bus integrity problems, + * the user needs to ensure that the GPIO Output Data Register - + * GPOD bits associated with an I2C port are cleared prior to setting + * the enable bit for that I2C serial port. + * The user prepares to enable I2C port 0 and + * I2C port 1 by clearing GPOD bits 7:6 and GPOD bits 5:4, respectively. + */ +#define IOP3XX_ICR_SCLEN 0x0020 /* 1=SCL enable for master mode */ +#define IOP3XX_ICR_MABORT 0x0010 /* 1=Send a STOP with no data + * NB TBYTE must be clear */ +#define IOP3XX_ICR_TBYTE 0x0008 /* 1=Send/Receive a byte. i2c clears */ +#define IOP3XX_ICR_NACK 0x0004 /* 1=reply with NACK */ +#define IOP3XX_ICR_MSTOP 0x0002 /* 1=send a STOP after next data byte */ +#define IOP3XX_ICR_MSTART 0x0001 /* 1=initiate a START */ + + +#define IOP3XX_ISR_BERRD 0x0400 /* 1=BUS ERROR Detected */ +#define IOP3XX_ISR_SAD 0x0200 /* 1=Slave ADdress Detected */ +#define IOP3XX_ISR_GCAD 0x0100 /* 1=General Call Address Detected */ +#define IOP3XX_ISR_RXFULL 0x0080 /* 1=Receive Full */ +#define IOP3XX_ISR_TXEMPTY 0x0040 /* 1=Transmit Empty */ +#define IOP3XX_ISR_ALD 0x0020 /* 1=Arbitration Loss Detected */ +#define IOP3XX_ISR_SSD 0x0010 /* 1=Slave STOP Detected */ +#define IOP3XX_ISR_BBUSY 0x0008 /* 1=Bus BUSY */ +#define IOP3XX_ISR_UNITBUSY 0x0004 /* 1=Unit Busy */ +#define IOP3XX_ISR_NACK 0x0002 /* 1=Unit Rx or Tx a NACK */ +#define IOP3XX_ISR_RXREAD 0x0001 /* 1=READ 0=WRITE (R/W bit of slave addr */ + +#define IOP3XX_ISR_CLEARBITS 0x07f0 + +#define IOP3XX_ISAR_SAMASK 0x007f + +#define IOP3XX_IDBR_MASK 0x00ff + +#define IOP3XX_IBMR_SCL 0x0002 +#define IOP3XX_IBMR_SDA 0x0001 + +#define IOP3XX_GPOD_I2C0 0x00c0 /* clear these bits to enable ch0 */ +#define IOP3XX_GPOD_I2C1 0x0030 /* clear these bits to enable ch1 */ + +#define MYSAR 0 /* default slave address */ + +#define I2C_ERR 321 +#define I2C_ERR_BERR (I2C_ERR+0) +#define I2C_ERR_ALD (I2C_ERR+1) + + +#define CR_OFFSET 0 +#define SR_OFFSET 0x4 +#define SAR_OFFSET 0x8 +#define DBR_OFFSET 0xc +#define CCR_OFFSET 0x10 +#define BMR_OFFSET 0x14 + +#define IOP3XX_I2C_IO_SIZE 0x18 + +struct i2c_algo_iop3xx_data { + void __iomem *ioaddr; + wait_queue_head_t waitq; + spinlock_t lock; + u32 SR_enabled, SR_received; + int id; + struct gpio_desc *gpio_scl; + struct gpio_desc *gpio_sda; +}; + +#endif /* I2C_IOP3XX_H */ |