diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/i2c/busses/i2c-sis5595.c | 422 |
1 files changed, 422 insertions, 0 deletions
diff --git a/drivers/i2c/busses/i2c-sis5595.c b/drivers/i2c/busses/i2c-sis5595.c new file mode 100644 index 000000000..c793a5c14 --- /dev/null +++ b/drivers/i2c/busses/i2c-sis5595.c @@ -0,0 +1,422 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + Copyright (c) 1998, 1999 Frodo Looijaard <frodol@dds.nl> and + Philip Edelbrock <phil@netroedge.com> + +*/ + +/* Note: we assume there can only be one SIS5595 with one SMBus interface */ + +/* + Note: all have mfr. ID 0x1039. + SUPPORTED PCI ID + 5595 0008 + + Note: these chips contain a 0008 device which is incompatible with the + 5595. We recognize these by the presence of the listed + "blacklist" PCI ID and refuse to load. + + NOT SUPPORTED PCI ID BLACKLIST PCI ID + 540 0008 0540 + 550 0008 0550 + 5513 0008 5511 + 5581 0008 5597 + 5582 0008 5597 + 5597 0008 5597 + 5598 0008 5597/5598 + 630 0008 0630 + 645 0008 0645 + 646 0008 0646 + 648 0008 0648 + 650 0008 0650 + 651 0008 0651 + 730 0008 0730 + 735 0008 0735 + 745 0008 0745 + 746 0008 0746 +*/ + +/* TO DO: + * Add Block Transfers (ugly, but supported by the adapter) + * Add adapter resets + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/delay.h> +#include <linux/pci.h> +#include <linux/ioport.h> +#include <linux/init.h> +#include <linux/i2c.h> +#include <linux/acpi.h> +#include <linux/io.h> + +static int blacklist[] = { + PCI_DEVICE_ID_SI_540, + PCI_DEVICE_ID_SI_550, + PCI_DEVICE_ID_SI_630, + PCI_DEVICE_ID_SI_645, + PCI_DEVICE_ID_SI_646, + PCI_DEVICE_ID_SI_648, + PCI_DEVICE_ID_SI_650, + PCI_DEVICE_ID_SI_651, + PCI_DEVICE_ID_SI_730, + PCI_DEVICE_ID_SI_735, + PCI_DEVICE_ID_SI_745, + PCI_DEVICE_ID_SI_746, + PCI_DEVICE_ID_SI_5511, /* 5513 chip has the 0008 device but that ID + shows up in other chips so we use the 5511 + ID for recognition */ + PCI_DEVICE_ID_SI_5597, + PCI_DEVICE_ID_SI_5598, + 0, /* terminates the list */ +}; + +/* Length of ISA address segment */ +#define SIS5595_EXTENT 8 +/* SIS5595 SMBus registers */ +#define SMB_STS_LO 0x00 +#define SMB_STS_HI 0x01 +#define SMB_CTL_LO 0x02 +#define SMB_CTL_HI 0x03 +#define SMB_ADDR 0x04 +#define SMB_CMD 0x05 +#define SMB_PCNT 0x06 +#define SMB_CNT 0x07 +#define SMB_BYTE 0x08 +#define SMB_DEV 0x10 +#define SMB_DB0 0x11 +#define SMB_DB1 0x12 +#define SMB_HAA 0x13 + +/* PCI Address Constants */ +#define SMB_INDEX 0x38 +#define SMB_DAT 0x39 +#define SIS5595_ENABLE_REG 0x40 +#define ACPI_BASE 0x90 + +/* Other settings */ +#define MAX_TIMEOUT 500 + +/* SIS5595 constants */ +#define SIS5595_QUICK 0x00 +#define SIS5595_BYTE 0x02 +#define SIS5595_BYTE_DATA 0x04 +#define SIS5595_WORD_DATA 0x06 +#define SIS5595_PROC_CALL 0x08 +#define SIS5595_BLOCK_DATA 0x0A + +/* insmod parameters */ + +/* If force_addr is set to anything different from 0, we forcibly enable + the device at the given address. */ +static u16 force_addr; +module_param_hw(force_addr, ushort, ioport, 0); +MODULE_PARM_DESC(force_addr, "Initialize the base address of the i2c controller"); + +static struct pci_driver sis5595_driver; +static unsigned short sis5595_base; +static struct pci_dev *sis5595_pdev; + +static u8 sis5595_read(u8 reg) +{ + outb(reg, sis5595_base + SMB_INDEX); + return inb(sis5595_base + SMB_DAT); +} + +static void sis5595_write(u8 reg, u8 data) +{ + outb(reg, sis5595_base + SMB_INDEX); + outb(data, sis5595_base + SMB_DAT); +} + +static int sis5595_setup(struct pci_dev *SIS5595_dev) +{ + u16 a; + u8 val; + int *i; + int retval; + + /* Look for imposters */ + for (i = blacklist; *i != 0; i++) { + struct pci_dev *dev; + dev = pci_get_device(PCI_VENDOR_ID_SI, *i, NULL); + if (dev) { + dev_err(&SIS5595_dev->dev, "Looked for SIS5595 but found unsupported device %.4x\n", *i); + pci_dev_put(dev); + return -ENODEV; + } + } + + /* Determine the address of the SMBus areas */ + pci_read_config_word(SIS5595_dev, ACPI_BASE, &sis5595_base); + if (sis5595_base == 0 && force_addr == 0) { + dev_err(&SIS5595_dev->dev, "ACPI base address uninitialized - upgrade BIOS or use force_addr=0xaddr\n"); + return -ENODEV; + } + + if (force_addr) + sis5595_base = force_addr & ~(SIS5595_EXTENT - 1); + dev_dbg(&SIS5595_dev->dev, "ACPI Base address: %04x\n", sis5595_base); + + /* NB: We grab just the two SMBus registers here, but this may still + * interfere with ACPI :-( */ + retval = acpi_check_region(sis5595_base + SMB_INDEX, 2, + sis5595_driver.name); + if (retval) + return retval; + + if (!request_region(sis5595_base + SMB_INDEX, 2, + sis5595_driver.name)) { + dev_err(&SIS5595_dev->dev, "SMBus registers 0x%04x-0x%04x already in use!\n", + sis5595_base + SMB_INDEX, sis5595_base + SMB_INDEX + 1); + return -ENODEV; + } + + if (force_addr) { + dev_info(&SIS5595_dev->dev, "forcing ISA address 0x%04X\n", sis5595_base); + if (pci_write_config_word(SIS5595_dev, ACPI_BASE, sis5595_base) + != PCIBIOS_SUCCESSFUL) + goto error; + if (pci_read_config_word(SIS5595_dev, ACPI_BASE, &a) + != PCIBIOS_SUCCESSFUL) + goto error; + if ((a & ~(SIS5595_EXTENT - 1)) != sis5595_base) { + /* doesn't work for some chips! */ + dev_err(&SIS5595_dev->dev, "force address failed - not supported?\n"); + goto error; + } + } + + if (pci_read_config_byte(SIS5595_dev, SIS5595_ENABLE_REG, &val) + != PCIBIOS_SUCCESSFUL) + goto error; + if ((val & 0x80) == 0) { + dev_info(&SIS5595_dev->dev, "enabling ACPI\n"); + if (pci_write_config_byte(SIS5595_dev, SIS5595_ENABLE_REG, val | 0x80) + != PCIBIOS_SUCCESSFUL) + goto error; + if (pci_read_config_byte(SIS5595_dev, SIS5595_ENABLE_REG, &val) + != PCIBIOS_SUCCESSFUL) + goto error; + if ((val & 0x80) == 0) { + /* doesn't work for some chips? */ + dev_err(&SIS5595_dev->dev, "ACPI enable failed - not supported?\n"); + goto error; + } + } + + /* Everything is happy */ + return 0; + +error: + release_region(sis5595_base + SMB_INDEX, 2); + return -ENODEV; +} + +static int sis5595_transaction(struct i2c_adapter *adap) +{ + int temp; + int result = 0; + int timeout = 0; + + /* Make sure the SMBus host is ready to start transmitting */ + temp = sis5595_read(SMB_STS_LO) + (sis5595_read(SMB_STS_HI) << 8); + if (temp != 0x00) { + dev_dbg(&adap->dev, "SMBus busy (%04x). Resetting...\n", temp); + sis5595_write(SMB_STS_LO, temp & 0xff); + sis5595_write(SMB_STS_HI, temp >> 8); + if ((temp = sis5595_read(SMB_STS_LO) + (sis5595_read(SMB_STS_HI) << 8)) != 0x00) { + dev_dbg(&adap->dev, "Failed! (%02x)\n", temp); + return -EBUSY; + } else { + dev_dbg(&adap->dev, "Successful!\n"); + } + } + + /* start the transaction by setting bit 4 */ + sis5595_write(SMB_CTL_LO, sis5595_read(SMB_CTL_LO) | 0x10); + + /* We will always wait for a fraction of a second! */ + do { + msleep(1); + temp = sis5595_read(SMB_STS_LO); + } while (!(temp & 0x40) && (timeout++ < MAX_TIMEOUT)); + + /* If the SMBus is still busy, we give up */ + if (timeout > MAX_TIMEOUT) { + dev_dbg(&adap->dev, "SMBus Timeout!\n"); + result = -ETIMEDOUT; + } + + if (temp & 0x10) { + dev_dbg(&adap->dev, "Error: Failed bus transaction\n"); + result = -ENXIO; + } + + if (temp & 0x20) { + dev_err(&adap->dev, "Bus collision! SMBus may be locked until " + "next hard reset (or not...)\n"); + /* Clock stops and slave is stuck in mid-transmission */ + result = -EIO; + } + + temp = sis5595_read(SMB_STS_LO) + (sis5595_read(SMB_STS_HI) << 8); + if (temp != 0x00) { + sis5595_write(SMB_STS_LO, temp & 0xff); + sis5595_write(SMB_STS_HI, temp >> 8); + } + + temp = sis5595_read(SMB_STS_LO) + (sis5595_read(SMB_STS_HI) << 8); + if (temp != 0x00) + dev_dbg(&adap->dev, "Failed reset at end of transaction (%02x)\n", temp); + + return result; +} + +/* Return negative errno on error. */ +static s32 sis5595_access(struct i2c_adapter *adap, u16 addr, + unsigned short flags, char read_write, + u8 command, int size, union i2c_smbus_data *data) +{ + int status; + + switch (size) { + case I2C_SMBUS_QUICK: + sis5595_write(SMB_ADDR, ((addr & 0x7f) << 1) | (read_write & 0x01)); + size = SIS5595_QUICK; + break; + case I2C_SMBUS_BYTE: + sis5595_write(SMB_ADDR, ((addr & 0x7f) << 1) | (read_write & 0x01)); + if (read_write == I2C_SMBUS_WRITE) + sis5595_write(SMB_CMD, command); + size = SIS5595_BYTE; + break; + case I2C_SMBUS_BYTE_DATA: + sis5595_write(SMB_ADDR, ((addr & 0x7f) << 1) | (read_write & 0x01)); + sis5595_write(SMB_CMD, command); + if (read_write == I2C_SMBUS_WRITE) + sis5595_write(SMB_BYTE, data->byte); + size = SIS5595_BYTE_DATA; + break; + case I2C_SMBUS_PROC_CALL: + case I2C_SMBUS_WORD_DATA: + sis5595_write(SMB_ADDR, ((addr & 0x7f) << 1) | (read_write & 0x01)); + sis5595_write(SMB_CMD, command); + if (read_write == I2C_SMBUS_WRITE) { + sis5595_write(SMB_BYTE, data->word & 0xff); + sis5595_write(SMB_BYTE + 1, + (data->word & 0xff00) >> 8); + } + size = (size == I2C_SMBUS_PROC_CALL) ? SIS5595_PROC_CALL : SIS5595_WORD_DATA; + break; + default: + dev_warn(&adap->dev, "Unsupported transaction %d\n", size); + return -EOPNOTSUPP; + } + + sis5595_write(SMB_CTL_LO, ((size & 0x0E))); + + status = sis5595_transaction(adap); + if (status) + return status; + + if ((size != SIS5595_PROC_CALL) && + ((read_write == I2C_SMBUS_WRITE) || (size == SIS5595_QUICK))) + return 0; + + + switch (size) { + case SIS5595_BYTE: + case SIS5595_BYTE_DATA: + data->byte = sis5595_read(SMB_BYTE); + break; + case SIS5595_WORD_DATA: + case SIS5595_PROC_CALL: + data->word = sis5595_read(SMB_BYTE) + (sis5595_read(SMB_BYTE + 1) << 8); + break; + } + return 0; +} + +static u32 sis5595_func(struct i2c_adapter *adapter) +{ + return I2C_FUNC_SMBUS_QUICK | I2C_FUNC_SMBUS_BYTE | + I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA | + I2C_FUNC_SMBUS_PROC_CALL; +} + +static const struct i2c_algorithm smbus_algorithm = { + .smbus_xfer = sis5595_access, + .functionality = sis5595_func, +}; + +static struct i2c_adapter sis5595_adapter = { + .owner = THIS_MODULE, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, + .algo = &smbus_algorithm, +}; + +static const struct pci_device_id sis5595_ids[] = { + { PCI_DEVICE(PCI_VENDOR_ID_SI, PCI_DEVICE_ID_SI_503) }, + { 0, } +}; + +MODULE_DEVICE_TABLE (pci, sis5595_ids); + +static int sis5595_probe(struct pci_dev *dev, const struct pci_device_id *id) +{ + int err; + + if (sis5595_setup(dev)) { + dev_err(&dev->dev, "SIS5595 not detected, module not inserted.\n"); + return -ENODEV; + } + + /* set up the sysfs linkage to our parent device */ + sis5595_adapter.dev.parent = &dev->dev; + + snprintf(sis5595_adapter.name, sizeof(sis5595_adapter.name), + "SMBus SIS5595 adapter at %04x", sis5595_base + SMB_INDEX); + err = i2c_add_adapter(&sis5595_adapter); + if (err) { + release_region(sis5595_base + SMB_INDEX, 2); + return err; + } + + /* Always return failure here. This is to allow other drivers to bind + * to this pci device. We don't really want to have control over the + * pci device, we only wanted to read as few register values from it. + */ + sis5595_pdev = pci_dev_get(dev); + return -ENODEV; +} + +static struct pci_driver sis5595_driver = { + .name = "sis5595_smbus", + .id_table = sis5595_ids, + .probe = sis5595_probe, +}; + +static int __init i2c_sis5595_init(void) +{ + return pci_register_driver(&sis5595_driver); +} + +static void __exit i2c_sis5595_exit(void) +{ + pci_unregister_driver(&sis5595_driver); + if (sis5595_pdev) { + i2c_del_adapter(&sis5595_adapter); + release_region(sis5595_base + SMB_INDEX, 2); + pci_dev_put(sis5595_pdev); + sis5595_pdev = NULL; + } +} + +MODULE_AUTHOR("Frodo Looijaard <frodol@dds.nl>"); +MODULE_DESCRIPTION("SIS5595 SMBus driver"); +MODULE_LICENSE("GPL"); + +module_init(i2c_sis5595_init); +module_exit(i2c_sis5595_exit); |