diff options
Diffstat (limited to 'drivers/i2c/muxes/Kconfig')
| -rw-r--r-- | drivers/i2c/muxes/Kconfig | 122 |
1 files changed, 122 insertions, 0 deletions
diff --git a/drivers/i2c/muxes/Kconfig b/drivers/i2c/muxes/Kconfig new file mode 100644 index 000000000..ea838dbae --- /dev/null +++ b/drivers/i2c/muxes/Kconfig @@ -0,0 +1,122 @@ +# SPDX-License-Identifier: GPL-2.0-only +# +# Multiplexer I2C chip drivers configuration +# + +menu "Multiplexer I2C Chip support" + depends on I2C_MUX + +config I2C_ARB_GPIO_CHALLENGE + tristate "GPIO-based I2C arbitration" + depends on GPIOLIB || COMPILE_TEST + depends on OF + help + If you say yes to this option, support will be included for an + I2C multimaster arbitration scheme using GPIOs and a challenge & + response mechanism where masters have to claim the bus by asserting + a GPIO. + + This driver can also be built as a module. If so, the module + will be called i2c-arb-gpio-challenge. + +config I2C_MUX_GPIO + tristate "GPIO-based I2C multiplexer" + depends on GPIOLIB + help + If you say yes to this option, support will be included for a + GPIO based I2C multiplexer. This driver provides access to + I2C busses connected through a MUX, which is controlled + through GPIO pins. + + This driver can also be built as a module. If so, the module + will be called i2c-mux-gpio. + +config I2C_MUX_GPMUX + tristate "General Purpose I2C multiplexer" + select MULTIPLEXER + depends on OF + help + If you say yes to this option, support will be included for a + general purpose I2C multiplexer. This driver provides access to + I2C busses connected through a MUX, which in turn is controlled + by a MUX-controller from the MUX subsystem. + + This driver can also be built as a module. If so, the module + will be called i2c-mux-gpmux. + +config I2C_MUX_LTC4306 + tristate "LTC LTC4306/5 I2C multiplexer" + select GPIOLIB + select REGMAP_I2C + help + If you say yes here you get support for the Analog Devices + LTC4306 or LTC4305 I2C mux/switch devices. + + This driver can also be built as a module. If so, the module + will be called i2c-mux-ltc4306. + +config I2C_MUX_PCA9541 + tristate "NXP PCA9541 I2C Master Selector" + help + If you say yes here you get support for the NXP PCA9541 + I2C Master Selector. + + This driver can also be built as a module. If so, the module + will be called i2c-mux-pca9541. + +config I2C_MUX_PCA954x + tristate "NXP PCA954x and PCA984x I2C Mux/switches" + depends on GPIOLIB || COMPILE_TEST + help + If you say yes here you get support for the NXP PCA954x + and PCA984x I2C mux/switch devices. + + This driver can also be built as a module. If so, the module + will be called i2c-mux-pca954x. + +config I2C_MUX_PINCTRL + tristate "pinctrl-based I2C multiplexer" + depends on PINCTRL + depends on OF + help + If you say yes to this option, support will be included for an I2C + multiplexer that uses the pinctrl subsystem, i.e. pin multiplexing. + This is useful for SoCs whose I2C module's signals can be routed to + different sets of pins at run-time. + + This driver can also be built as a module. If so, the module will be + called i2c-mux-pinctrl. + +config I2C_MUX_REG + tristate "Register-based I2C multiplexer" + depends on HAS_IOMEM + help + If you say yes to this option, support will be included for a + register based I2C multiplexer. This driver provides access to + I2C busses connected through a MUX, which is controlled + by a single register. + + This driver can also be built as a module. If so, the module + will be called i2c-mux-reg. + +config I2C_DEMUX_PINCTRL + tristate "pinctrl-based I2C demultiplexer" + depends on PINCTRL && OF + select OF_DYNAMIC + help + If you say yes to this option, support will be included for an I2C + demultiplexer that uses the pinctrl subsystem. This is useful if you + want to change the I2C master at run-time depending on features. + +config I2C_MUX_MLXCPLD + tristate "Mellanox CPLD based I2C multiplexer" + help + If you say yes to this option, support will be included for a + CPLD based I2C multiplexer. This driver provides access to + I2C busses connected through a MUX, which is controlled + by a CPLD register. + + This driver can also be built as a module. If so, the module + will be called i2c-mux-mlxcpld. + +endmenu |