diff options
Diffstat (limited to 'drivers/irqchip/alphascale_asm9260-icoll.h')
| -rw-r--r-- | drivers/irqchip/alphascale_asm9260-icoll.h | 105 |
1 files changed, 105 insertions, 0 deletions
diff --git a/drivers/irqchip/alphascale_asm9260-icoll.h b/drivers/irqchip/alphascale_asm9260-icoll.h new file mode 100644 index 000000000..1ec59483a --- /dev/null +++ b/drivers/irqchip/alphascale_asm9260-icoll.h @@ -0,0 +1,105 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ +/* + * Copyright (C) 2014 Oleksij Rempel <linux@rempel-privat.de> + */ + +#ifndef _ALPHASCALE_ASM9260_ICOLL_H +#define _ALPHASCALE_ASM9260_ICOLL_H + +#define ASM9260_NUM_IRQS 64 +/* + * this device provide 4 offsets for each register: + * 0x0 - plain read write mode + * 0x4 - set mode, OR logic. + * 0x8 - clr mode, XOR logic. + * 0xc - togle mode. + */ + +#define ASM9260_HW_ICOLL_VECTOR 0x0000 +/* + * bits 31:2 + * This register presents the vector address for the interrupt currently + * active on the CPU IRQ input. Writing to this register notifies the + * interrupt collector that the interrupt service routine for the current + * interrupt has been entered. + * The exception trap should have a LDPC instruction from this address: + * LDPC ASM9260_HW_ICOLL_VECTOR_ADDR; IRQ exception at 0xffff0018 + */ + +/* + * The Interrupt Collector Level Acknowledge Register is used by software to + * indicate the completion of an interrupt on a specific level. + * This register is written at the very end of an interrupt service routine. If + * nesting is used then the CPU irq must be turned on before writing to this + * register to avoid a race condition in the CPU interrupt hardware. + */ +#define ASM9260_HW_ICOLL_LEVELACK 0x0010 +#define ASM9260_BM_LEVELn(nr) BIT(nr) + +#define ASM9260_HW_ICOLL_CTRL 0x0020 +/* + * ASM9260_BM_CTRL_SFTRST and ASM9260_BM_CTRL_CLKGATE are not available on + * asm9260. + */ +#define ASM9260_BM_CTRL_SFTRST BIT(31) +#define ASM9260_BM_CTRL_CLKGATE BIT(30) +/* disable interrupt level nesting */ +#define ASM9260_BM_CTRL_NO_NESTING BIT(19) +/* + * Set this bit to one enable the RISC32-style read side effect associated with + * the vector address register. In this mode, interrupt in-service is signaled + * by the read of the ASM9260_HW_ICOLL_VECTOR register to acquire the interrupt + * vector address. Set this bit to zero for normal operation, in which the ISR + * signals in-service explicitly by means of a write to the + * ASM9260_HW_ICOLL_VECTOR register. + * 0 - Must Write to Vector register to go in-service. + * 1 - Go in-service as a read side effect + */ +#define ASM9260_BM_CTRL_ARM_RSE_MODE BIT(18) +#define ASM9260_BM_CTRL_IRQ_ENABLE BIT(16) + +#define ASM9260_HW_ICOLL_STAT_OFFSET 0x0030 +/* + * bits 5:0 + * Vector number of current interrupt. Multiply by 4 and add to vector base + * address to obtain the value in ASM9260_HW_ICOLL_VECTOR. + */ + +/* + * RAW0 and RAW1 provides a read-only view of the raw interrupt request lines + * coming from various parts of the chip. Its purpose is to improve diagnostic + * observability. + */ +#define ASM9260_HW_ICOLL_RAW0 0x0040 +#define ASM9260_HW_ICOLL_RAW1 0x0050 + +#define ASM9260_HW_ICOLL_INTERRUPT0 0x0060 +#define ASM9260_HW_ICOLL_INTERRUPTn(n) (0x0060 + ((n) >> 2) * 0x10) +/* + * WARNING: Modifying the priority of an enabled interrupt may result in + * undefined behavior. + */ +#define ASM9260_BM_INT_PRIORITY_MASK 0x3 +#define ASM9260_BM_INT_ENABLE BIT(2) +#define ASM9260_BM_INT_SOFTIRQ BIT(3) + +#define ASM9260_BM_ICOLL_INTERRUPTn_SHIFT(n) (((n) & 0x3) << 3) +#define ASM9260_BM_ICOLL_INTERRUPTn_ENABLE(n) (1 << (2 + \ + ASM9260_BM_ICOLL_INTERRUPTn_SHIFT(n))) + +#define ASM9260_HW_ICOLL_VBASE 0x0160 +/* + * bits 31:2 + * This bitfield holds the upper 30 bits of the base address of the vector + * table. + */ + +#define ASM9260_HW_ICOLL_CLEAR0 0x01d0 +#define ASM9260_HW_ICOLL_CLEAR1 0x01e0 +#define ASM9260_HW_ICOLL_CLEARn(n) (((n >> 5) * 0x10) \ + + SET_REG) +#define ASM9260_BM_CLEAR_BIT(n) BIT(n & 0x1f) + +/* Scratchpad */ +#define ASM9260_HW_ICOLL_UNDEF_VECTOR 0x01f0 +#endif |