diff options
Diffstat (limited to 'drivers/net/dsa/qca/ar9331.c')
| -rw-r--r-- | drivers/net/dsa/qca/ar9331.c | 1135 |
1 files changed, 1135 insertions, 0 deletions
diff --git a/drivers/net/dsa/qca/ar9331.c b/drivers/net/dsa/qca/ar9331.c new file mode 100644 index 000000000..e7b98b864 --- /dev/null +++ b/drivers/net/dsa/qca/ar9331.c @@ -0,0 +1,1135 @@ +// SPDX-License-Identifier: GPL-2.0-only +// Copyright (c) 2019 Pengutronix, Oleksij Rempel <kernel@pengutronix.de> +/* + * +----------------------+ + * GMAC1----RGMII----|--MAC0 | + * \---MDIO1----|--REGs |----MDIO3----\ + * | | | +------+ + * | | +--| | + * | MAC1-|----RMII--M-----| PHY0 |-o P0 + * | | | | +------+ + * | | | +--| | + * | MAC2-|----RMII--------| PHY1 |-o P1 + * | | | | +------+ + * | | | +--| | + * | MAC3-|----RMII--------| PHY2 |-o P2 + * | | | | +------+ + * | | | +--| | + * | MAC4-|----RMII--------| PHY3 |-o P3 + * | | | | +------+ + * | | | +--| | + * | MAC5-|--+-RMII--M-----|-PHY4-|-o P4 + * | | | | +------+ + * +----------------------+ | \--CFG_SW_PHY_SWAP + * GMAC0---------------RMII--------------------/ \-CFG_SW_PHY_ADDR_SWAP + * \---MDIO0--NC + * + * GMAC0 and MAC5 are connected together and use same PHY. Depending on + * configuration it can be PHY4 (default) or PHY0. Only GMAC0 or MAC5 can be + * used at same time. If GMAC0 is used (default) then MAC5 should be disabled. + * + * CFG_SW_PHY_SWAP - swap connections of PHY0 and PHY4. If this bit is not set + * PHY4 is connected to GMAC0/MAC5 bundle and PHY0 is connected to MAC1. If this + * bit is set, PHY4 is connected to MAC1 and PHY0 is connected to GMAC0/MAC5 + * bundle. + * + * CFG_SW_PHY_ADDR_SWAP - swap addresses of PHY0 and PHY4 + * + * CFG_SW_PHY_SWAP and CFG_SW_PHY_ADDR_SWAP are part of SoC specific register + * set and not related to switch internal registers. + */ + +#include <linux/bitfield.h> +#include <linux/module.h> +#include <linux/of_irq.h> +#include <linux/of_mdio.h> +#include <linux/regmap.h> +#include <linux/reset.h> +#include <net/dsa.h> + +#define AR9331_SW_NAME "ar9331_switch" +#define AR9331_SW_PORTS 6 + +/* dummy reg to change page */ +#define AR9331_SW_REG_PAGE 0x40000 + +/* Global Interrupt */ +#define AR9331_SW_REG_GINT 0x10 +#define AR9331_SW_REG_GINT_MASK 0x14 +#define AR9331_SW_GINT_PHY_INT BIT(2) + +#define AR9331_SW_REG_FLOOD_MASK 0x2c +#define AR9331_SW_FLOOD_MASK_BROAD_TO_CPU BIT(26) + +#define AR9331_SW_REG_GLOBAL_CTRL 0x30 +#define AR9331_SW_GLOBAL_CTRL_MFS_M GENMASK(13, 0) + +#define AR9331_SW_REG_MDIO_CTRL 0x98 +#define AR9331_SW_MDIO_CTRL_BUSY BIT(31) +#define AR9331_SW_MDIO_CTRL_MASTER_EN BIT(30) +#define AR9331_SW_MDIO_CTRL_CMD_READ BIT(27) +#define AR9331_SW_MDIO_CTRL_PHY_ADDR_M GENMASK(25, 21) +#define AR9331_SW_MDIO_CTRL_REG_ADDR_M GENMASK(20, 16) +#define AR9331_SW_MDIO_CTRL_DATA_M GENMASK(16, 0) + +#define AR9331_SW_REG_PORT_STATUS(_port) (0x100 + (_port) * 0x100) + +/* FLOW_LINK_EN - enable mac flow control config auto-neg with phy. + * If not set, mac can be config by software. + */ +#define AR9331_SW_PORT_STATUS_FLOW_LINK_EN BIT(12) + +/* LINK_EN - If set, MAC is configured from PHY link status. + * If not set, MAC should be configured by software. + */ +#define AR9331_SW_PORT_STATUS_LINK_EN BIT(9) +#define AR9331_SW_PORT_STATUS_DUPLEX_MODE BIT(6) +#define AR9331_SW_PORT_STATUS_RX_FLOW_EN BIT(5) +#define AR9331_SW_PORT_STATUS_TX_FLOW_EN BIT(4) +#define AR9331_SW_PORT_STATUS_RXMAC BIT(3) +#define AR9331_SW_PORT_STATUS_TXMAC BIT(2) +#define AR9331_SW_PORT_STATUS_SPEED_M GENMASK(1, 0) +#define AR9331_SW_PORT_STATUS_SPEED_1000 2 +#define AR9331_SW_PORT_STATUS_SPEED_100 1 +#define AR9331_SW_PORT_STATUS_SPEED_10 0 + +#define AR9331_SW_PORT_STATUS_MAC_MASK \ + (AR9331_SW_PORT_STATUS_TXMAC | AR9331_SW_PORT_STATUS_RXMAC) + +#define AR9331_SW_PORT_STATUS_LINK_MASK \ + (AR9331_SW_PORT_STATUS_DUPLEX_MODE | \ + AR9331_SW_PORT_STATUS_RX_FLOW_EN | AR9331_SW_PORT_STATUS_TX_FLOW_EN | \ + AR9331_SW_PORT_STATUS_SPEED_M) + +#define AR9331_SW_REG_PORT_CTRL(_port) (0x104 + (_port) * 0x100) +#define AR9331_SW_PORT_CTRL_HEAD_EN BIT(11) +#define AR9331_SW_PORT_CTRL_PORT_STATE GENMASK(2, 0) +#define AR9331_SW_PORT_CTRL_PORT_STATE_DISABLED 0 +#define AR9331_SW_PORT_CTRL_PORT_STATE_BLOCKING 1 +#define AR9331_SW_PORT_CTRL_PORT_STATE_LISTENING 2 +#define AR9331_SW_PORT_CTRL_PORT_STATE_LEARNING 3 +#define AR9331_SW_PORT_CTRL_PORT_STATE_FORWARD 4 + +#define AR9331_SW_REG_PORT_VLAN(_port) (0x108 + (_port) * 0x100) +#define AR9331_SW_PORT_VLAN_8021Q_MODE GENMASK(31, 30) +#define AR9331_SW_8021Q_MODE_SECURE 3 +#define AR9331_SW_8021Q_MODE_CHECK 2 +#define AR9331_SW_8021Q_MODE_FALLBACK 1 +#define AR9331_SW_8021Q_MODE_NONE 0 +#define AR9331_SW_PORT_VLAN_PORT_VID_MEMBER GENMASK(25, 16) + +/* MIB registers */ +#define AR9331_MIB_COUNTER(x) (0x20000 + ((x) * 0x100)) + +/* Phy bypass mode + * ------------------------------------------------------------------------ + * Bit: | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |10 |11 |12 |13 |14 |15 | + * + * real | start | OP | PhyAddr | Reg Addr | TA | + * atheros| start | OP | 2'b00 |PhyAdd[2:0]| Reg Addr[4:0] | TA | + * + * + * Bit: |16 |17 |18 |19 |20 |21 |22 |23 |24 |25 |26 |27 |28 |29 |30 |31 | + * real | Data | + * atheros| Data | + * + * ------------------------------------------------------------------------ + * Page address mode + * ------------------------------------------------------------------------ + * Bit: | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |10 |11 |12 |13 |14 |15 | + * real | start | OP | PhyAddr | Reg Addr | TA | + * atheros| start | OP | 2'b11 | 8'b0 | TA | + * + * Bit: |16 |17 |18 |19 |20 |21 |22 |23 |24 |25 |26 |27 |28 |29 |30 |31 | + * real | Data | + * atheros| | Page [9:0] | + */ +/* In case of Page Address mode, Bit[18:9] of 32 bit register address should be + * written to bits[9:0] of mdio data register. + */ +#define AR9331_SW_ADDR_PAGE GENMASK(18, 9) + +/* ------------------------------------------------------------------------ + * Normal register access mode + * ------------------------------------------------------------------------ + * Bit: | 0 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |10 |11 |12 |13 |14 |15 | + * real | start | OP | PhyAddr | Reg Addr | TA | + * atheros| start | OP | 2'b10 | low_addr[7:0] | TA | + * + * Bit: |16 |17 |18 |19 |20 |21 |22 |23 |24 |25 |26 |27 |28 |29 |30 |31 | + * real | Data | + * atheros| Data | + * ------------------------------------------------------------------------ + */ +#define AR9331_SW_LOW_ADDR_PHY GENMASK(8, 6) +#define AR9331_SW_LOW_ADDR_REG GENMASK(5, 1) + +#define AR9331_SW_MDIO_PHY_MODE_M GENMASK(4, 3) +#define AR9331_SW_MDIO_PHY_MODE_PAGE 3 +#define AR9331_SW_MDIO_PHY_MODE_REG 2 +#define AR9331_SW_MDIO_PHY_MODE_BYPASS 0 +#define AR9331_SW_MDIO_PHY_ADDR_M GENMASK(2, 0) + +/* Empirical determined values */ +#define AR9331_SW_MDIO_POLL_SLEEP_US 1 +#define AR9331_SW_MDIO_POLL_TIMEOUT_US 20 + +/* The interval should be small enough to avoid overflow of 32bit MIBs */ +/* + * FIXME: until we can read MIBs from stats64 call directly (i.e. sleep + * there), we have to poll stats more frequently then it is actually needed. + * For overflow protection, normally, 100 sec interval should have been OK. + */ +#define STATS_INTERVAL_JIFFIES (3 * HZ) + +struct ar9331_sw_stats_raw { + u32 rxbroad; /* 0x00 */ + u32 rxpause; /* 0x04 */ + u32 rxmulti; /* 0x08 */ + u32 rxfcserr; /* 0x0c */ + u32 rxalignerr; /* 0x10 */ + u32 rxrunt; /* 0x14 */ + u32 rxfragment; /* 0x18 */ + u32 rx64byte; /* 0x1c */ + u32 rx128byte; /* 0x20 */ + u32 rx256byte; /* 0x24 */ + u32 rx512byte; /* 0x28 */ + u32 rx1024byte; /* 0x2c */ + u32 rx1518byte; /* 0x30 */ + u32 rxmaxbyte; /* 0x34 */ + u32 rxtoolong; /* 0x38 */ + u32 rxgoodbyte; /* 0x3c */ + u32 rxgoodbyte_hi; + u32 rxbadbyte; /* 0x44 */ + u32 rxbadbyte_hi; + u32 rxoverflow; /* 0x4c */ + u32 filtered; /* 0x50 */ + u32 txbroad; /* 0x54 */ + u32 txpause; /* 0x58 */ + u32 txmulti; /* 0x5c */ + u32 txunderrun; /* 0x60 */ + u32 tx64byte; /* 0x64 */ + u32 tx128byte; /* 0x68 */ + u32 tx256byte; /* 0x6c */ + u32 tx512byte; /* 0x70 */ + u32 tx1024byte; /* 0x74 */ + u32 tx1518byte; /* 0x78 */ + u32 txmaxbyte; /* 0x7c */ + u32 txoversize; /* 0x80 */ + u32 txbyte; /* 0x84 */ + u32 txbyte_hi; + u32 txcollision; /* 0x8c */ + u32 txabortcol; /* 0x90 */ + u32 txmulticol; /* 0x94 */ + u32 txsinglecol; /* 0x98 */ + u32 txexcdefer; /* 0x9c */ + u32 txdefer; /* 0xa0 */ + u32 txlatecol; /* 0xa4 */ +}; + +struct ar9331_sw_port { + int idx; + struct delayed_work mib_read; + struct rtnl_link_stats64 stats; + struct ethtool_pause_stats pause_stats; + struct spinlock stats_lock; +}; + +struct ar9331_sw_priv { + struct device *dev; + struct dsa_switch ds; + struct dsa_switch_ops ops; + struct irq_domain *irqdomain; + u32 irq_mask; + struct mutex lock_irq; + struct mii_bus *mbus; /* mdio master */ + struct mii_bus *sbus; /* mdio slave */ + struct regmap *regmap; + struct reset_control *sw_reset; + struct ar9331_sw_port port[AR9331_SW_PORTS]; +}; + +static struct ar9331_sw_priv *ar9331_sw_port_to_priv(struct ar9331_sw_port *port) +{ + struct ar9331_sw_port *p = port - port->idx; + + return (struct ar9331_sw_priv *)((void *)p - + offsetof(struct ar9331_sw_priv, port)); +} + +/* Warning: switch reset will reset last AR9331_SW_MDIO_PHY_MODE_PAGE request + * If some kind of optimization is used, the request should be repeated. + */ +static int ar9331_sw_reset(struct ar9331_sw_priv *priv) +{ + int ret; + + ret = reset_control_assert(priv->sw_reset); + if (ret) + goto error; + + /* AR9331 doc do not provide any information about proper reset + * sequence. The AR8136 (the closes switch to the AR9331) doc says: + * reset duration should be greater than 10ms. So, let's use this value + * for now. + */ + usleep_range(10000, 15000); + ret = reset_control_deassert(priv->sw_reset); + if (ret) + goto error; + /* There is no information on how long should we wait after reset. + * AR8136 has an EEPROM and there is an Interrupt for EEPROM load + * status. AR9331 has no EEPROM support. + * For now, do not wait. In case AR8136 will be needed, the after + * reset delay can be added as well. + */ + + return 0; +error: + dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret); + return ret; +} + +static int ar9331_sw_mbus_write(struct mii_bus *mbus, int port, int regnum, + u16 data) +{ + struct ar9331_sw_priv *priv = mbus->priv; + struct regmap *regmap = priv->regmap; + u32 val; + int ret; + + ret = regmap_write(regmap, AR9331_SW_REG_MDIO_CTRL, + AR9331_SW_MDIO_CTRL_BUSY | + AR9331_SW_MDIO_CTRL_MASTER_EN | + FIELD_PREP(AR9331_SW_MDIO_CTRL_PHY_ADDR_M, port) | + FIELD_PREP(AR9331_SW_MDIO_CTRL_REG_ADDR_M, regnum) | + FIELD_PREP(AR9331_SW_MDIO_CTRL_DATA_M, data)); + if (ret) + goto error; + + ret = regmap_read_poll_timeout(regmap, AR9331_SW_REG_MDIO_CTRL, val, + !(val & AR9331_SW_MDIO_CTRL_BUSY), + AR9331_SW_MDIO_POLL_SLEEP_US, + AR9331_SW_MDIO_POLL_TIMEOUT_US); + if (ret) + goto error; + + return 0; +error: + dev_err_ratelimited(priv->dev, "PHY write error: %i\n", ret); + return ret; +} + +static int ar9331_sw_mbus_read(struct mii_bus *mbus, int port, int regnum) +{ + struct ar9331_sw_priv *priv = mbus->priv; + struct regmap *regmap = priv->regmap; + u32 val; + int ret; + + ret = regmap_write(regmap, AR9331_SW_REG_MDIO_CTRL, + AR9331_SW_MDIO_CTRL_BUSY | + AR9331_SW_MDIO_CTRL_MASTER_EN | + AR9331_SW_MDIO_CTRL_CMD_READ | + FIELD_PREP(AR9331_SW_MDIO_CTRL_PHY_ADDR_M, port) | + FIELD_PREP(AR9331_SW_MDIO_CTRL_REG_ADDR_M, regnum)); + if (ret) + goto error; + + ret = regmap_read_poll_timeout(regmap, AR9331_SW_REG_MDIO_CTRL, val, + !(val & AR9331_SW_MDIO_CTRL_BUSY), + AR9331_SW_MDIO_POLL_SLEEP_US, + AR9331_SW_MDIO_POLL_TIMEOUT_US); + if (ret) + goto error; + + ret = regmap_read(regmap, AR9331_SW_REG_MDIO_CTRL, &val); + if (ret) + goto error; + + return FIELD_GET(AR9331_SW_MDIO_CTRL_DATA_M, val); + +error: + dev_err_ratelimited(priv->dev, "PHY read error: %i\n", ret); + return ret; +} + +static int ar9331_sw_mbus_init(struct ar9331_sw_priv *priv) +{ + struct device *dev = priv->dev; + struct mii_bus *mbus; + struct device_node *np, *mnp; + int ret; + + np = dev->of_node; + + mbus = devm_mdiobus_alloc(dev); + if (!mbus) + return -ENOMEM; + + mbus->name = np->full_name; + snprintf(mbus->id, MII_BUS_ID_SIZE, "%pOF", np); + + mbus->read = ar9331_sw_mbus_read; + mbus->write = ar9331_sw_mbus_write; + mbus->priv = priv; + mbus->parent = dev; + + mnp = of_get_child_by_name(np, "mdio"); + if (!mnp) + return -ENODEV; + + ret = devm_of_mdiobus_register(dev, mbus, mnp); + of_node_put(mnp); + if (ret) + return ret; + + priv->mbus = mbus; + + return 0; +} + +static int ar9331_sw_setup_port(struct dsa_switch *ds, int port) +{ + struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv; + struct regmap *regmap = priv->regmap; + u32 port_mask, port_ctrl, val; + int ret; + + /* Generate default port settings */ + port_ctrl = FIELD_PREP(AR9331_SW_PORT_CTRL_PORT_STATE, + AR9331_SW_PORT_CTRL_PORT_STATE_FORWARD); + + if (dsa_is_cpu_port(ds, port)) { + /* CPU port should be allowed to communicate with all user + * ports. + */ + port_mask = dsa_user_ports(ds); + /* Enable Atheros header on CPU port. This will allow us + * communicate with each port separately + */ + port_ctrl |= AR9331_SW_PORT_CTRL_HEAD_EN; + } else if (dsa_is_user_port(ds, port)) { + /* User ports should communicate only with the CPU port. + */ + port_mask = BIT(dsa_upstream_port(ds, port)); + } else { + /* Other ports do not need to communicate at all */ + port_mask = 0; + } + + val = FIELD_PREP(AR9331_SW_PORT_VLAN_8021Q_MODE, + AR9331_SW_8021Q_MODE_NONE) | + FIELD_PREP(AR9331_SW_PORT_VLAN_PORT_VID_MEMBER, port_mask); + + ret = regmap_write(regmap, AR9331_SW_REG_PORT_VLAN(port), val); + if (ret) + goto error; + + ret = regmap_write(regmap, AR9331_SW_REG_PORT_CTRL(port), port_ctrl); + if (ret) + goto error; + + return 0; +error: + dev_err(priv->dev, "%s: error: %i\n", __func__, ret); + + return ret; +} + +static int ar9331_sw_setup(struct dsa_switch *ds) +{ + struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv; + struct regmap *regmap = priv->regmap; + int ret, i; + + ret = ar9331_sw_reset(priv); + if (ret) + return ret; + + /* Reset will set proper defaults. CPU - Port0 will be enabled and + * configured. All other ports (ports 1 - 5) are disabled + */ + ret = ar9331_sw_mbus_init(priv); + if (ret) + return ret; + + /* Do not drop broadcast frames */ + ret = regmap_write_bits(regmap, AR9331_SW_REG_FLOOD_MASK, + AR9331_SW_FLOOD_MASK_BROAD_TO_CPU, + AR9331_SW_FLOOD_MASK_BROAD_TO_CPU); + if (ret) + goto error; + + /* Set max frame size to the maximum supported value */ + ret = regmap_write_bits(regmap, AR9331_SW_REG_GLOBAL_CTRL, + AR9331_SW_GLOBAL_CTRL_MFS_M, + AR9331_SW_GLOBAL_CTRL_MFS_M); + if (ret) + goto error; + + for (i = 0; i < ds->num_ports; i++) { + ret = ar9331_sw_setup_port(ds, i); + if (ret) + goto error; + } + + ds->configure_vlan_while_not_filtering = false; + + return 0; +error: + dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret); + return ret; +} + +static void ar9331_sw_port_disable(struct dsa_switch *ds, int port) +{ + struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv; + struct regmap *regmap = priv->regmap; + int ret; + + ret = regmap_write(regmap, AR9331_SW_REG_PORT_STATUS(port), 0); + if (ret) + dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret); +} + +static enum dsa_tag_protocol ar9331_sw_get_tag_protocol(struct dsa_switch *ds, + int port, + enum dsa_tag_protocol m) +{ + return DSA_TAG_PROTO_AR9331; +} + +static void ar9331_sw_phylink_get_caps(struct dsa_switch *ds, int port, + struct phylink_config *config) +{ + config->mac_capabilities = MAC_ASYM_PAUSE | MAC_SYM_PAUSE | + MAC_10 | MAC_100; + + switch (port) { + case 0: + __set_bit(PHY_INTERFACE_MODE_GMII, + config->supported_interfaces); + config->mac_capabilities |= MAC_1000; + break; + case 1: + case 2: + case 3: + case 4: + case 5: + __set_bit(PHY_INTERFACE_MODE_INTERNAL, + config->supported_interfaces); + break; + } +} + +static void ar9331_sw_phylink_mac_config(struct dsa_switch *ds, int port, + unsigned int mode, + const struct phylink_link_state *state) +{ + struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv; + struct regmap *regmap = priv->regmap; + int ret; + + ret = regmap_update_bits(regmap, AR9331_SW_REG_PORT_STATUS(port), + AR9331_SW_PORT_STATUS_LINK_EN | + AR9331_SW_PORT_STATUS_FLOW_LINK_EN, 0); + if (ret) + dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret); +} + +static void ar9331_sw_phylink_mac_link_down(struct dsa_switch *ds, int port, + unsigned int mode, + phy_interface_t interface) +{ + struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv; + struct ar9331_sw_port *p = &priv->port[port]; + struct regmap *regmap = priv->regmap; + int ret; + + ret = regmap_update_bits(regmap, AR9331_SW_REG_PORT_STATUS(port), + AR9331_SW_PORT_STATUS_MAC_MASK, 0); + if (ret) + dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret); + + cancel_delayed_work_sync(&p->mib_read); +} + +static void ar9331_sw_phylink_mac_link_up(struct dsa_switch *ds, int port, + unsigned int mode, + phy_interface_t interface, + struct phy_device *phydev, + int speed, int duplex, + bool tx_pause, bool rx_pause) +{ + struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv; + struct ar9331_sw_port *p = &priv->port[port]; + struct regmap *regmap = priv->regmap; + u32 val; + int ret; + + schedule_delayed_work(&p->mib_read, 0); + + val = AR9331_SW_PORT_STATUS_MAC_MASK; + switch (speed) { + case SPEED_1000: + val |= AR9331_SW_PORT_STATUS_SPEED_1000; + break; + case SPEED_100: + val |= AR9331_SW_PORT_STATUS_SPEED_100; + break; + case SPEED_10: + val |= AR9331_SW_PORT_STATUS_SPEED_10; + break; + default: + return; + } + + if (duplex) + val |= AR9331_SW_PORT_STATUS_DUPLEX_MODE; + + if (tx_pause) + val |= AR9331_SW_PORT_STATUS_TX_FLOW_EN; + + if (rx_pause) + val |= AR9331_SW_PORT_STATUS_RX_FLOW_EN; + + ret = regmap_update_bits(regmap, AR9331_SW_REG_PORT_STATUS(port), + AR9331_SW_PORT_STATUS_MAC_MASK | + AR9331_SW_PORT_STATUS_LINK_MASK, + val); + if (ret) + dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret); +} + +static void ar9331_read_stats(struct ar9331_sw_port *port) +{ + struct ar9331_sw_priv *priv = ar9331_sw_port_to_priv(port); + struct ethtool_pause_stats *pstats = &port->pause_stats; + struct rtnl_link_stats64 *stats = &port->stats; + struct ar9331_sw_stats_raw raw; + int ret; + + /* Do the slowest part first, to avoid needless locking for long time */ + ret = regmap_bulk_read(priv->regmap, AR9331_MIB_COUNTER(port->idx), + &raw, sizeof(raw) / sizeof(u32)); + if (ret) { + dev_err_ratelimited(priv->dev, "%s: %i\n", __func__, ret); + return; + } + /* All MIB counters are cleared automatically on read */ + + spin_lock(&port->stats_lock); + + stats->rx_bytes += raw.rxgoodbyte; + stats->tx_bytes += raw.txbyte; + + stats->rx_packets += raw.rx64byte + raw.rx128byte + raw.rx256byte + + raw.rx512byte + raw.rx1024byte + raw.rx1518byte + raw.rxmaxbyte; + stats->tx_packets += raw.tx64byte + raw.tx128byte + raw.tx256byte + + raw.tx512byte + raw.tx1024byte + raw.tx1518byte + raw.txmaxbyte; + + stats->rx_length_errors += raw.rxrunt + raw.rxfragment + raw.rxtoolong; + stats->rx_crc_errors += raw.rxfcserr; + stats->rx_frame_errors += raw.rxalignerr; + stats->rx_missed_errors += raw.rxoverflow; + stats->rx_dropped += raw.filtered; + stats->rx_errors += raw.rxfcserr + raw.rxalignerr + raw.rxrunt + + raw.rxfragment + raw.rxoverflow + raw.rxtoolong; + + stats->tx_window_errors += raw.txlatecol; + stats->tx_fifo_errors += raw.txunderrun; + stats->tx_aborted_errors += raw.txabortcol; + stats->tx_errors += raw.txoversize + raw.txabortcol + raw.txunderrun + + raw.txlatecol; + + stats->multicast += raw.rxmulti; + stats->collisions += raw.txcollision; + + pstats->tx_pause_frames += raw.txpause; + pstats->rx_pause_frames += raw.rxpause; + + spin_unlock(&port->stats_lock); +} + +static void ar9331_do_stats_poll(struct work_struct *work) +{ + struct ar9331_sw_port *port = container_of(work, struct ar9331_sw_port, + mib_read.work); + + ar9331_read_stats(port); + + schedule_delayed_work(&port->mib_read, STATS_INTERVAL_JIFFIES); +} + +static void ar9331_get_stats64(struct dsa_switch *ds, int port, + struct rtnl_link_stats64 *s) +{ + struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv; + struct ar9331_sw_port *p = &priv->port[port]; + + spin_lock(&p->stats_lock); + memcpy(s, &p->stats, sizeof(*s)); + spin_unlock(&p->stats_lock); +} + +static void ar9331_get_pause_stats(struct dsa_switch *ds, int port, + struct ethtool_pause_stats *pause_stats) +{ + struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ds->priv; + struct ar9331_sw_port *p = &priv->port[port]; + + spin_lock(&p->stats_lock); + memcpy(pause_stats, &p->pause_stats, sizeof(*pause_stats)); + spin_unlock(&p->stats_lock); +} + +static const struct dsa_switch_ops ar9331_sw_ops = { + .get_tag_protocol = ar9331_sw_get_tag_protocol, + .setup = ar9331_sw_setup, + .port_disable = ar9331_sw_port_disable, + .phylink_get_caps = ar9331_sw_phylink_get_caps, + .phylink_mac_config = ar9331_sw_phylink_mac_config, + .phylink_mac_link_down = ar9331_sw_phylink_mac_link_down, + .phylink_mac_link_up = ar9331_sw_phylink_mac_link_up, + .get_stats64 = ar9331_get_stats64, + .get_pause_stats = ar9331_get_pause_stats, +}; + +static irqreturn_t ar9331_sw_irq(int irq, void *data) +{ + struct ar9331_sw_priv *priv = data; + struct regmap *regmap = priv->regmap; + u32 stat; + int ret; + + ret = regmap_read(regmap, AR9331_SW_REG_GINT, &stat); + if (ret) { + dev_err(priv->dev, "can't read interrupt status\n"); + return IRQ_NONE; + } + + if (!stat) + return IRQ_NONE; + + if (stat & AR9331_SW_GINT_PHY_INT) { + int child_irq; + + child_irq = irq_find_mapping(priv->irqdomain, 0); + handle_nested_irq(child_irq); + } + + ret = regmap_write(regmap, AR9331_SW_REG_GINT, stat); + if (ret) { + dev_err(priv->dev, "can't write interrupt status\n"); + return IRQ_NONE; + } + + return IRQ_HANDLED; +} + +static void ar9331_sw_mask_irq(struct irq_data *d) +{ + struct ar9331_sw_priv *priv = irq_data_get_irq_chip_data(d); + + priv->irq_mask = 0; +} + +static void ar9331_sw_unmask_irq(struct irq_data *d) +{ + struct ar9331_sw_priv *priv = irq_data_get_irq_chip_data(d); + + priv->irq_mask = AR9331_SW_GINT_PHY_INT; +} + +static void ar9331_sw_irq_bus_lock(struct irq_data *d) +{ + struct ar9331_sw_priv *priv = irq_data_get_irq_chip_data(d); + + mutex_lock(&priv->lock_irq); +} + +static void ar9331_sw_irq_bus_sync_unlock(struct irq_data *d) +{ + struct ar9331_sw_priv *priv = irq_data_get_irq_chip_data(d); + struct regmap *regmap = priv->regmap; + int ret; + + ret = regmap_update_bits(regmap, AR9331_SW_REG_GINT_MASK, + AR9331_SW_GINT_PHY_INT, priv->irq_mask); + if (ret) + dev_err(priv->dev, "failed to change IRQ mask\n"); + + mutex_unlock(&priv->lock_irq); +} + +static struct irq_chip ar9331_sw_irq_chip = { + .name = AR9331_SW_NAME, + .irq_mask = ar9331_sw_mask_irq, + .irq_unmask = ar9331_sw_unmask_irq, + .irq_bus_lock = ar9331_sw_irq_bus_lock, + .irq_bus_sync_unlock = ar9331_sw_irq_bus_sync_unlock, +}; + +static int ar9331_sw_irq_map(struct irq_domain *domain, unsigned int irq, + irq_hw_number_t hwirq) +{ + irq_set_chip_data(irq, domain->host_data); + irq_set_chip_and_handler(irq, &ar9331_sw_irq_chip, handle_simple_irq); + irq_set_nested_thread(irq, 1); + irq_set_noprobe(irq); + + return 0; +} + +static void ar9331_sw_irq_unmap(struct irq_domain *d, unsigned int irq) +{ + irq_set_nested_thread(irq, 0); + irq_set_chip_and_handler(irq, NULL, NULL); + irq_set_chip_data(irq, NULL); +} + +static const struct irq_domain_ops ar9331_sw_irqdomain_ops = { + .map = ar9331_sw_irq_map, + .unmap = ar9331_sw_irq_unmap, + .xlate = irq_domain_xlate_onecell, +}; + +static int ar9331_sw_irq_init(struct ar9331_sw_priv *priv) +{ + struct device_node *np = priv->dev->of_node; + struct device *dev = priv->dev; + int ret, irq; + + irq = of_irq_get(np, 0); + if (irq <= 0) { + dev_err(dev, "failed to get parent IRQ\n"); + return irq ? irq : -EINVAL; + } + + mutex_init(&priv->lock_irq); + ret = devm_request_threaded_irq(dev, irq, NULL, ar9331_sw_irq, + IRQF_ONESHOT, AR9331_SW_NAME, priv); + if (ret) { + dev_err(dev, "unable to request irq: %d\n", ret); + return ret; + } + + priv->irqdomain = irq_domain_add_linear(np, 1, &ar9331_sw_irqdomain_ops, + priv); + if (!priv->irqdomain) { + dev_err(dev, "failed to create IRQ domain\n"); + return -EINVAL; + } + + irq_set_parent(irq_create_mapping(priv->irqdomain, 0), irq); + + return 0; +} + +static int __ar9331_mdio_write(struct mii_bus *sbus, u8 mode, u16 reg, u16 val) +{ + u8 r, p; + + p = FIELD_PREP(AR9331_SW_MDIO_PHY_MODE_M, mode) | + FIELD_GET(AR9331_SW_LOW_ADDR_PHY, reg); + r = FIELD_GET(AR9331_SW_LOW_ADDR_REG, reg); + + return __mdiobus_write(sbus, p, r, val); +} + +static int __ar9331_mdio_read(struct mii_bus *sbus, u16 reg) +{ + u8 r, p; + + p = FIELD_PREP(AR9331_SW_MDIO_PHY_MODE_M, AR9331_SW_MDIO_PHY_MODE_REG) | + FIELD_GET(AR9331_SW_LOW_ADDR_PHY, reg); + r = FIELD_GET(AR9331_SW_LOW_ADDR_REG, reg); + + return __mdiobus_read(sbus, p, r); +} + +static int ar9331_mdio_read(void *ctx, const void *reg_buf, size_t reg_len, + void *val_buf, size_t val_len) +{ + struct ar9331_sw_priv *priv = ctx; + struct mii_bus *sbus = priv->sbus; + u32 reg = *(u32 *)reg_buf; + int ret; + + if (reg == AR9331_SW_REG_PAGE) { + /* We cannot read the page selector register from hardware and + * we cache its value in regmap. Return all bits set here, + * that regmap will always write the page on first use. + */ + *(u32 *)val_buf = GENMASK(9, 0); + return 0; + } + + mutex_lock_nested(&sbus->mdio_lock, MDIO_MUTEX_NESTED); + + ret = __ar9331_mdio_read(sbus, reg); + if (ret < 0) + goto error; + + *(u32 *)val_buf = ret; + ret = __ar9331_mdio_read(sbus, reg + 2); + if (ret < 0) + goto error; + + *(u32 *)val_buf |= ret << 16; + + mutex_unlock(&sbus->mdio_lock); + + return 0; +error: + mutex_unlock(&sbus->mdio_lock); + dev_err_ratelimited(&sbus->dev, "Bus error. Failed to read register.\n"); + + return ret; +} + +static int ar9331_mdio_write(void *ctx, u32 reg, u32 val) +{ + struct ar9331_sw_priv *priv = (struct ar9331_sw_priv *)ctx; + struct mii_bus *sbus = priv->sbus; + int ret; + + mutex_lock_nested(&sbus->mdio_lock, MDIO_MUTEX_NESTED); + if (reg == AR9331_SW_REG_PAGE) { + ret = __ar9331_mdio_write(sbus, AR9331_SW_MDIO_PHY_MODE_PAGE, + 0, val); + if (ret < 0) + goto error; + + mutex_unlock(&sbus->mdio_lock); + + return 0; + } + + /* In case of this switch we work with 32bit registers on top of 16bit + * bus. Some registers (for example access to forwarding database) have + * trigger bit on the first 16bit half of request, the result and + * configuration of request in the second half. + * To make it work properly, we should do the second part of transfer + * before the first one is done. + */ + ret = __ar9331_mdio_write(sbus, AR9331_SW_MDIO_PHY_MODE_REG, reg + 2, + val >> 16); + if (ret < 0) + goto error; + + ret = __ar9331_mdio_write(sbus, AR9331_SW_MDIO_PHY_MODE_REG, reg, val); + if (ret < 0) + goto error; + + mutex_unlock(&sbus->mdio_lock); + + return 0; + +error: + mutex_unlock(&sbus->mdio_lock); + dev_err_ratelimited(&sbus->dev, "Bus error. Failed to write register.\n"); + + return ret; +} + +static int ar9331_sw_bus_write(void *context, const void *data, size_t count) +{ + u32 reg = *(u32 *)data; + u32 val = *((u32 *)data + 1); + + return ar9331_mdio_write(context, reg, val); +} + +static const struct regmap_range ar9331_valid_regs[] = { + regmap_reg_range(0x0, 0x0), + regmap_reg_range(0x10, 0x14), + regmap_reg_range(0x20, 0x24), + regmap_reg_range(0x2c, 0x30), + regmap_reg_range(0x40, 0x44), + regmap_reg_range(0x50, 0x78), + regmap_reg_range(0x80, 0x98), + + regmap_reg_range(0x100, 0x120), + regmap_reg_range(0x200, 0x220), + regmap_reg_range(0x300, 0x320), + regmap_reg_range(0x400, 0x420), + regmap_reg_range(0x500, 0x520), + regmap_reg_range(0x600, 0x620), + + regmap_reg_range(0x20000, 0x200a4), + regmap_reg_range(0x20100, 0x201a4), + regmap_reg_range(0x20200, 0x202a4), + regmap_reg_range(0x20300, 0x203a4), + regmap_reg_range(0x20400, 0x204a4), + regmap_reg_range(0x20500, 0x205a4), + + /* dummy page selector reg */ + regmap_reg_range(AR9331_SW_REG_PAGE, AR9331_SW_REG_PAGE), +}; + +static const struct regmap_range ar9331_nonvolatile_regs[] = { + regmap_reg_range(AR9331_SW_REG_PAGE, AR9331_SW_REG_PAGE), +}; + +static const struct regmap_range_cfg ar9331_regmap_range[] = { + { + .selector_reg = AR9331_SW_REG_PAGE, + .selector_mask = GENMASK(9, 0), + .selector_shift = 0, + + .window_start = 0, + .window_len = 512, + + .range_min = 0, + .range_max = AR9331_SW_REG_PAGE - 4, + }, +}; + +static const struct regmap_access_table ar9331_register_set = { + .yes_ranges = ar9331_valid_regs, + .n_yes_ranges = ARRAY_SIZE(ar9331_valid_regs), +}; + +static const struct regmap_access_table ar9331_volatile_set = { + .no_ranges = ar9331_nonvolatile_regs, + .n_no_ranges = ARRAY_SIZE(ar9331_nonvolatile_regs), +}; + +static const struct regmap_config ar9331_mdio_regmap_config = { + .reg_bits = 32, + .val_bits = 32, + .reg_stride = 4, + .max_register = AR9331_SW_REG_PAGE, + + .ranges = ar9331_regmap_range, + .num_ranges = ARRAY_SIZE(ar9331_regmap_range), + + .volatile_table = &ar9331_volatile_set, + .wr_table = &ar9331_register_set, + .rd_table = &ar9331_register_set, + + .cache_type = REGCACHE_RBTREE, +}; + +static struct regmap_bus ar9331_sw_bus = { + .reg_format_endian_default = REGMAP_ENDIAN_NATIVE, + .val_format_endian_default = REGMAP_ENDIAN_NATIVE, + .read = ar9331_mdio_read, + .write = ar9331_sw_bus_write, + .max_raw_read = 4, + .max_raw_write = 4, +}; + +static int ar9331_sw_probe(struct mdio_device *mdiodev) +{ + struct ar9331_sw_priv *priv; + struct dsa_switch *ds; + int ret, i; + + priv = devm_kzalloc(&mdiodev->dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + priv->regmap = devm_regmap_init(&mdiodev->dev, &ar9331_sw_bus, priv, + &ar9331_mdio_regmap_config); + if (IS_ERR(priv->regmap)) { + ret = PTR_ERR(priv->regmap); + dev_err(&mdiodev->dev, "regmap init failed: %d\n", ret); + return ret; + } + + priv->sw_reset = devm_reset_control_get(&mdiodev->dev, "switch"); + if (IS_ERR(priv->sw_reset)) { + dev_err(&mdiodev->dev, "missing switch reset\n"); + return PTR_ERR(priv->sw_reset); + } + + priv->sbus = mdiodev->bus; + priv->dev = &mdiodev->dev; + + ret = ar9331_sw_irq_init(priv); + if (ret) + return ret; + + ds = &priv->ds; + ds->dev = &mdiodev->dev; + ds->num_ports = AR9331_SW_PORTS; + ds->priv = priv; + priv->ops = ar9331_sw_ops; + ds->ops = &priv->ops; + dev_set_drvdata(&mdiodev->dev, priv); + + for (i = 0; i < ARRAY_SIZE(priv->port); i++) { + struct ar9331_sw_port *port = &priv->port[i]; + + port->idx = i; + spin_lock_init(&port->stats_lock); + INIT_DELAYED_WORK(&port->mib_read, ar9331_do_stats_poll); + } + + ret = dsa_register_switch(ds); + if (ret) + goto err_remove_irq; + + return 0; + +err_remove_irq: + irq_domain_remove(priv->irqdomain); + + return ret; +} + +static void ar9331_sw_remove(struct mdio_device *mdiodev) +{ + struct ar9331_sw_priv *priv = dev_get_drvdata(&mdiodev->dev); + unsigned int i; + + if (!priv) + return; + + for (i = 0; i < ARRAY_SIZE(priv->port); i++) { + struct ar9331_sw_port *port = &priv->port[i]; + + cancel_delayed_work_sync(&port->mib_read); + } + + irq_domain_remove(priv->irqdomain); + dsa_unregister_switch(&priv->ds); + + reset_control_assert(priv->sw_reset); +} + +static void ar9331_sw_shutdown(struct mdio_device *mdiodev) +{ + struct ar9331_sw_priv *priv = dev_get_drvdata(&mdiodev->dev); + + if (!priv) + return; + + dsa_switch_shutdown(&priv->ds); + + dev_set_drvdata(&mdiodev->dev, NULL); +} + +static const struct of_device_id ar9331_sw_of_match[] = { + { .compatible = "qca,ar9331-switch" }, + { }, +}; + +static struct mdio_driver ar9331_sw_mdio_driver = { + .probe = ar9331_sw_probe, + .remove = ar9331_sw_remove, + .shutdown = ar9331_sw_shutdown, + .mdiodrv.driver = { + .name = AR9331_SW_NAME, + .of_match_table = ar9331_sw_of_match, + }, +}; + +mdio_module_driver(ar9331_sw_mdio_driver); + +MODULE_AUTHOR("Oleksij Rempel <kernel@pengutronix.de>"); +MODULE_DESCRIPTION("Driver for Atheros AR9331 switch"); +MODULE_LICENSE("GPL v2"); |