diff options
Diffstat (limited to 'drivers/net/ethernet/8390/axnet_cs.c')
| -rw-r--r-- | drivers/net/ethernet/8390/axnet_cs.c | 1710 |
1 files changed, 1710 insertions, 0 deletions
diff --git a/drivers/net/ethernet/8390/axnet_cs.c b/drivers/net/ethernet/8390/axnet_cs.c new file mode 100644 index 000000000..3aef959fc --- /dev/null +++ b/drivers/net/ethernet/8390/axnet_cs.c @@ -0,0 +1,1710 @@ +/*====================================================================== + + A PCMCIA ethernet driver for Asix AX88190-based cards + + The Asix AX88190 is a NS8390-derived chipset with a few nasty + idiosyncracies that make it very inconvenient to support with a + standard 8390 driver. This driver is based on pcnet_cs, with the + tweaked 8390 code grafted on the end. Much of what I did was to + clean up and update a similar driver supplied by Asix, which was + adapted by William Lee, william@asix.com.tw. + + Copyright (C) 2001 David A. Hinds -- dahinds@users.sourceforge.net + + axnet_cs.c 1.28 2002/06/29 06:27:37 + + The network driver code is based on Donald Becker's NE2000 code: + + Written 1992,1993 by Donald Becker. + Copyright 1993 United States Government as represented by the + Director, National Security Agency. This software may be used and + distributed according to the terms of the GNU General Public License, + incorporated herein by reference. + Donald Becker may be reached at becker@scyld.com + +======================================================================*/ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/ptrace.h> +#include <linux/string.h> +#include <linux/timer.h> +#include <linux/delay.h> +#include <linux/spinlock.h> +#include <linux/netdevice.h> +#include <linux/etherdevice.h> +#include <linux/crc32.h> +#include <linux/mii.h> +#include "8390.h" + +#include <pcmcia/cistpl.h> +#include <pcmcia/ciscode.h> +#include <pcmcia/ds.h> +#include <pcmcia/cisreg.h> + +#include <asm/io.h> +#include <asm/byteorder.h> +#include <linux/uaccess.h> + +#define AXNET_CMD 0x00 +#define AXNET_DATAPORT 0x10 /* NatSemi-defined port window offset. */ +#define AXNET_RESET 0x1f /* Issue a read to reset, a write to clear. */ +#define AXNET_MII_EEP 0x14 /* Offset of MII access port */ +#define AXNET_TEST 0x15 /* Offset of TEST Register port */ +#define AXNET_GPIO 0x17 /* Offset of General Purpose Register Port */ + +#define AXNET_START_PG 0x40 /* First page of TX buffer */ +#define AXNET_STOP_PG 0x80 /* Last page +1 of RX ring */ + +#define AXNET_RDC_TIMEOUT 0x02 /* Max wait in jiffies for Tx RDC */ + +#define IS_AX88190 0x0001 +#define IS_AX88790 0x0002 + +/*====================================================================*/ + +/* Module parameters */ + +MODULE_AUTHOR("David Hinds <dahinds@users.sourceforge.net>"); +MODULE_DESCRIPTION("Asix AX88190 PCMCIA ethernet driver"); +MODULE_LICENSE("GPL"); + + +/*====================================================================*/ + +static int axnet_config(struct pcmcia_device *link); +static void axnet_release(struct pcmcia_device *link); +static int axnet_open(struct net_device *dev); +static int axnet_close(struct net_device *dev); +static int axnet_ioctl(struct net_device *dev, struct ifreq *rq, int cmd); +static netdev_tx_t axnet_start_xmit(struct sk_buff *skb, + struct net_device *dev); +static struct net_device_stats *get_stats(struct net_device *dev); +static void set_multicast_list(struct net_device *dev); +static void axnet_tx_timeout(struct net_device *dev, unsigned int txqueue); +static irqreturn_t ei_irq_wrapper(int irq, void *dev_id); +static void ei_watchdog(struct timer_list *t); +static void axnet_reset_8390(struct net_device *dev); + +static int mdio_read(unsigned int addr, int phy_id, int loc); +static void mdio_write(unsigned int addr, int phy_id, int loc, int value); + +static void get_8390_hdr(struct net_device *, + struct e8390_pkt_hdr *, int); +static void block_input(struct net_device *dev, int count, + struct sk_buff *skb, int ring_offset); +static void block_output(struct net_device *dev, int count, + const u_char *buf, const int start_page); + +static void axnet_detach(struct pcmcia_device *p_dev); + +static void AX88190_init(struct net_device *dev, int startp); +static int ax_open(struct net_device *dev); +static int ax_close(struct net_device *dev); +static irqreturn_t ax_interrupt(int irq, void *dev_id); + +/*====================================================================*/ + +struct axnet_dev { + struct pcmcia_device *p_dev; + caddr_t base; + struct timer_list watchdog; + int stale, fast_poll; + u_short link_status; + u_char duplex_flag; + int phy_id; + int flags; + int active_low; +}; + +static inline struct axnet_dev *PRIV(struct net_device *dev) +{ + void *p = (char *)netdev_priv(dev) + sizeof(struct ei_device); + return p; +} + +static const struct net_device_ops axnet_netdev_ops = { + .ndo_open = axnet_open, + .ndo_stop = axnet_close, + .ndo_eth_ioctl = axnet_ioctl, + .ndo_start_xmit = axnet_start_xmit, + .ndo_tx_timeout = axnet_tx_timeout, + .ndo_get_stats = get_stats, + .ndo_set_rx_mode = set_multicast_list, + .ndo_set_mac_address = eth_mac_addr, + .ndo_validate_addr = eth_validate_addr, +}; + +static int axnet_probe(struct pcmcia_device *link) +{ + struct axnet_dev *info; + struct net_device *dev; + struct ei_device *ei_local; + + dev_dbg(&link->dev, "axnet_attach()\n"); + + dev = alloc_etherdev(sizeof(struct ei_device) + sizeof(struct axnet_dev)); + if (!dev) + return -ENOMEM; + + ei_local = netdev_priv(dev); + spin_lock_init(&ei_local->page_lock); + + info = PRIV(dev); + info->p_dev = link; + link->priv = dev; + link->config_flags |= CONF_ENABLE_IRQ; + + dev->netdev_ops = &axnet_netdev_ops; + + dev->watchdog_timeo = TX_TIMEOUT; + + return axnet_config(link); +} /* axnet_attach */ + +static void axnet_detach(struct pcmcia_device *link) +{ + struct net_device *dev = link->priv; + + dev_dbg(&link->dev, "axnet_detach(0x%p)\n", link); + + unregister_netdev(dev); + + axnet_release(link); + + free_netdev(dev); +} /* axnet_detach */ + +/*====================================================================== + + This probes for a card's hardware address by reading the PROM. + +======================================================================*/ + +static int get_prom(struct pcmcia_device *link) +{ + struct net_device *dev = link->priv; + unsigned int ioaddr = dev->base_addr; + u8 addr[ETH_ALEN]; + int i, j; + + /* This is based on drivers/net/ethernet/8390/ne.c */ + struct { + u_char value, offset; + } program_seq[] = { + {E8390_NODMA+E8390_PAGE0+E8390_STOP, E8390_CMD}, /* Select page 0*/ + {0x01, EN0_DCFG}, /* Set word-wide access. */ + {0x00, EN0_RCNTLO}, /* Clear the count regs. */ + {0x00, EN0_RCNTHI}, + {0x00, EN0_IMR}, /* Mask completion irq. */ + {0xFF, EN0_ISR}, + {E8390_RXOFF|0x40, EN0_RXCR}, /* 0x60 Set to monitor */ + {E8390_TXOFF, EN0_TXCR}, /* 0x02 and loopback mode. */ + {0x10, EN0_RCNTLO}, + {0x00, EN0_RCNTHI}, + {0x00, EN0_RSARLO}, /* DMA starting at 0x0400. */ + {0x04, EN0_RSARHI}, + {E8390_RREAD+E8390_START, E8390_CMD}, + }; + + /* Not much of a test, but the alternatives are messy */ + if (link->config_base != 0x03c0) + return 0; + + axnet_reset_8390(dev); + mdelay(10); + + for (i = 0; i < ARRAY_SIZE(program_seq); i++) + outb_p(program_seq[i].value, ioaddr + program_seq[i].offset); + + for (i = 0; i < 6; i += 2) { + j = inw(ioaddr + AXNET_DATAPORT); + addr[i] = j & 0xff; + addr[i+1] = j >> 8; + } + eth_hw_addr_set(dev, addr); + + return 1; +} /* get_prom */ + +static int try_io_port(struct pcmcia_device *link) +{ + int j, ret; + link->resource[0]->flags &= ~IO_DATA_PATH_WIDTH; + link->resource[1]->flags &= ~IO_DATA_PATH_WIDTH; + if (link->resource[0]->end == 32) { + link->resource[0]->flags |= IO_DATA_PATH_WIDTH_AUTO; + /* for master/slave multifunction cards */ + if (link->resource[1]->end > 0) + link->resource[1]->flags |= IO_DATA_PATH_WIDTH_8; + } else { + /* This should be two 16-port windows */ + link->resource[0]->flags |= IO_DATA_PATH_WIDTH_8; + link->resource[1]->flags |= IO_DATA_PATH_WIDTH_16; + } + if (link->resource[0]->start == 0) { + for (j = 0; j < 0x400; j += 0x20) { + link->resource[0]->start = j ^ 0x300; + link->resource[1]->start = (j ^ 0x300) + 0x10; + link->io_lines = 16; + ret = pcmcia_request_io(link); + if (ret == 0) + return ret; + } + return ret; + } else { + return pcmcia_request_io(link); + } +} + +static int axnet_configcheck(struct pcmcia_device *p_dev, void *priv_data) +{ + if (p_dev->config_index == 0) + return -EINVAL; + + p_dev->config_index = 0x05; + if (p_dev->resource[0]->end + p_dev->resource[1]->end < 32) + return -ENODEV; + + return try_io_port(p_dev); +} + +static int axnet_config(struct pcmcia_device *link) +{ + struct net_device *dev = link->priv; + struct axnet_dev *info = PRIV(dev); + int i, j, j2, ret; + + dev_dbg(&link->dev, "axnet_config(0x%p)\n", link); + + /* don't trust the CIS on this; Linksys got it wrong */ + link->config_regs = 0x63; + link->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_SET_IO; + ret = pcmcia_loop_config(link, axnet_configcheck, NULL); + if (ret != 0) + goto failed; + + if (!link->irq) + goto failed; + + if (resource_size(link->resource[1]) == 8) + link->config_flags |= CONF_ENABLE_SPKR; + + ret = pcmcia_enable_device(link); + if (ret) + goto failed; + + dev->irq = link->irq; + dev->base_addr = link->resource[0]->start; + + if (!get_prom(link)) { + pr_notice("this is not an AX88190 card!\n"); + pr_notice("use pcnet_cs instead.\n"); + goto failed; + } + + ei_status.name = "AX88190"; + ei_status.word16 = 1; + ei_status.tx_start_page = AXNET_START_PG; + ei_status.rx_start_page = AXNET_START_PG + TX_PAGES; + ei_status.stop_page = AXNET_STOP_PG; + ei_status.reset_8390 = axnet_reset_8390; + ei_status.get_8390_hdr = get_8390_hdr; + ei_status.block_input = block_input; + ei_status.block_output = block_output; + + if (inb(dev->base_addr + AXNET_TEST) != 0) + info->flags |= IS_AX88790; + else + info->flags |= IS_AX88190; + + if (info->flags & IS_AX88790) + outb(0x10, dev->base_addr + AXNET_GPIO); /* select Internal PHY */ + + info->active_low = 0; + + for (i = 0; i < 32; i++) { + j = mdio_read(dev->base_addr + AXNET_MII_EEP, i, 1); + j2 = mdio_read(dev->base_addr + AXNET_MII_EEP, i, 2); + if (j == j2) continue; + if ((j != 0) && (j != 0xffff)) break; + } + + if (i == 32) { + /* Maybe PHY is in power down mode. (PPD_SET = 1) + Bit 2 of CCSR is active low. */ + pcmcia_write_config_byte(link, CISREG_CCSR, 0x04); + for (i = 0; i < 32; i++) { + j = mdio_read(dev->base_addr + AXNET_MII_EEP, i, 1); + j2 = mdio_read(dev->base_addr + AXNET_MII_EEP, i, 2); + if (j == j2) continue; + if ((j != 0) && (j != 0xffff)) { + info->active_low = 1; + break; + } + } + } + + info->phy_id = (i < 32) ? i : -1; + SET_NETDEV_DEV(dev, &link->dev); + + if (register_netdev(dev) != 0) { + pr_notice("register_netdev() failed\n"); + goto failed; + } + + netdev_info(dev, "Asix AX88%d90: io %#3lx, irq %d, hw_addr %pM\n", + ((info->flags & IS_AX88790) ? 7 : 1), + dev->base_addr, dev->irq, dev->dev_addr); + if (info->phy_id != -1) { + netdev_dbg(dev, " MII transceiver at index %d, status %x\n", + info->phy_id, j); + } else { + netdev_notice(dev, " No MII transceivers found!\n"); + } + return 0; + +failed: + axnet_release(link); + return -ENODEV; +} /* axnet_config */ + +static void axnet_release(struct pcmcia_device *link) +{ + pcmcia_disable_device(link); +} + +static int axnet_suspend(struct pcmcia_device *link) +{ + struct net_device *dev = link->priv; + + if (link->open) + netif_device_detach(dev); + + return 0; +} + +static int axnet_resume(struct pcmcia_device *link) +{ + struct net_device *dev = link->priv; + struct axnet_dev *info = PRIV(dev); + + if (link->open) { + if (info->active_low == 1) + pcmcia_write_config_byte(link, CISREG_CCSR, 0x04); + + axnet_reset_8390(dev); + AX88190_init(dev, 1); + netif_device_attach(dev); + } + + return 0; +} + + +/*====================================================================== + + MII interface support + +======================================================================*/ + +#define MDIO_SHIFT_CLK 0x01 +#define MDIO_DATA_WRITE0 0x00 +#define MDIO_DATA_WRITE1 0x08 +#define MDIO_DATA_READ 0x04 +#define MDIO_MASK 0x0f +#define MDIO_ENB_IN 0x02 + +static void mdio_sync(unsigned int addr) +{ + int bits; + for (bits = 0; bits < 32; bits++) { + outb_p(MDIO_DATA_WRITE1, addr); + outb_p(MDIO_DATA_WRITE1 | MDIO_SHIFT_CLK, addr); + } +} + +static int mdio_read(unsigned int addr, int phy_id, int loc) +{ + u_int cmd = (0xf6<<10)|(phy_id<<5)|loc; + int i, retval = 0; + + mdio_sync(addr); + for (i = 14; i >= 0; i--) { + int dat = (cmd&(1<<i)) ? MDIO_DATA_WRITE1 : MDIO_DATA_WRITE0; + outb_p(dat, addr); + outb_p(dat | MDIO_SHIFT_CLK, addr); + } + for (i = 19; i > 0; i--) { + outb_p(MDIO_ENB_IN, addr); + retval = (retval << 1) | ((inb_p(addr) & MDIO_DATA_READ) != 0); + outb_p(MDIO_ENB_IN | MDIO_SHIFT_CLK, addr); + } + return (retval>>1) & 0xffff; +} + +static void mdio_write(unsigned int addr, int phy_id, int loc, int value) +{ + u_int cmd = (0x05<<28)|(phy_id<<23)|(loc<<18)|(1<<17)|value; + int i; + + mdio_sync(addr); + for (i = 31; i >= 0; i--) { + int dat = (cmd&(1<<i)) ? MDIO_DATA_WRITE1 : MDIO_DATA_WRITE0; + outb_p(dat, addr); + outb_p(dat | MDIO_SHIFT_CLK, addr); + } + for (i = 1; i >= 0; i--) { + outb_p(MDIO_ENB_IN, addr); + outb_p(MDIO_ENB_IN | MDIO_SHIFT_CLK, addr); + } +} + +/*====================================================================*/ + +static int axnet_open(struct net_device *dev) +{ + int ret; + struct axnet_dev *info = PRIV(dev); + struct pcmcia_device *link = info->p_dev; + unsigned int nic_base = dev->base_addr; + + dev_dbg(&link->dev, "axnet_open('%s')\n", dev->name); + + if (!pcmcia_dev_present(link)) + return -ENODEV; + + outb_p(0xFF, nic_base + EN0_ISR); /* Clear bogus intr. */ + ret = request_irq(dev->irq, ei_irq_wrapper, IRQF_SHARED, "axnet_cs", dev); + if (ret) + return ret; + + link->open++; + + info->link_status = 0x00; + timer_setup(&info->watchdog, ei_watchdog, 0); + mod_timer(&info->watchdog, jiffies + HZ); + + return ax_open(dev); +} /* axnet_open */ + +/*====================================================================*/ + +static int axnet_close(struct net_device *dev) +{ + struct axnet_dev *info = PRIV(dev); + struct pcmcia_device *link = info->p_dev; + + dev_dbg(&link->dev, "axnet_close('%s')\n", dev->name); + + ax_close(dev); + free_irq(dev->irq, dev); + + link->open--; + netif_stop_queue(dev); + del_timer_sync(&info->watchdog); + + return 0; +} /* axnet_close */ + +/*====================================================================== + + Hard reset the card. This used to pause for the same period that + a 8390 reset command required, but that shouldn't be necessary. + +======================================================================*/ + +static void axnet_reset_8390(struct net_device *dev) +{ + unsigned int nic_base = dev->base_addr; + int i; + + ei_status.txing = ei_status.dmaing = 0; + + outb_p(E8390_NODMA+E8390_PAGE0+E8390_STOP, nic_base + E8390_CMD); + + outb(inb(nic_base + AXNET_RESET), nic_base + AXNET_RESET); + + for (i = 0; i < 100; i++) { + if ((inb_p(nic_base+EN0_ISR) & ENISR_RESET) != 0) + break; + udelay(100); + } + outb_p(ENISR_RESET, nic_base + EN0_ISR); /* Ack intr. */ + + if (i == 100) + netdev_err(dev, "axnet_reset_8390() did not complete\n"); + +} /* axnet_reset_8390 */ + +/*====================================================================*/ + +static irqreturn_t ei_irq_wrapper(int irq, void *dev_id) +{ + struct net_device *dev = dev_id; + PRIV(dev)->stale = 0; + return ax_interrupt(irq, dev_id); +} + +static void ei_watchdog(struct timer_list *t) +{ + struct axnet_dev *info = from_timer(info, t, watchdog); + struct net_device *dev = info->p_dev->priv; + unsigned int nic_base = dev->base_addr; + unsigned int mii_addr = nic_base + AXNET_MII_EEP; + u_short link; + + if (!netif_device_present(dev)) goto reschedule; + + /* Check for pending interrupt with expired latency timer: with + this, we can limp along even if the interrupt is blocked */ + if (info->stale++ && (inb_p(nic_base + EN0_ISR) & ENISR_ALL)) { + if (!info->fast_poll) + netdev_info(dev, "interrupt(s) dropped!\n"); + ei_irq_wrapper(dev->irq, dev); + info->fast_poll = HZ; + } + if (info->fast_poll) { + info->fast_poll--; + info->watchdog.expires = jiffies + 1; + add_timer(&info->watchdog); + return; + } + + if (info->phy_id < 0) + goto reschedule; + link = mdio_read(mii_addr, info->phy_id, 1); + if (!link || (link == 0xffff)) { + netdev_info(dev, "MII is missing!\n"); + info->phy_id = -1; + goto reschedule; + } + + link &= 0x0004; + if (link != info->link_status) { + u_short p = mdio_read(mii_addr, info->phy_id, 5); + netdev_info(dev, "%s link beat\n", link ? "found" : "lost"); + if (link) { + info->duplex_flag = (p & 0x0140) ? 0x80 : 0x00; + if (p) + netdev_info(dev, "autonegotiation complete: %dbaseT-%cD selected\n", + (p & 0x0180) ? 100 : 10, (p & 0x0140) ? 'F' : 'H'); + else + netdev_info(dev, "link partner did not autonegotiate\n"); + AX88190_init(dev, 1); + } + info->link_status = link; + } + +reschedule: + info->watchdog.expires = jiffies + HZ; + add_timer(&info->watchdog); +} + +/*====================================================================*/ + +static int axnet_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) +{ + struct axnet_dev *info = PRIV(dev); + struct mii_ioctl_data *data = if_mii(rq); + unsigned int mii_addr = dev->base_addr + AXNET_MII_EEP; + switch (cmd) { + case SIOCGMIIPHY: + data->phy_id = info->phy_id; + fallthrough; + case SIOCGMIIREG: /* Read MII PHY register. */ + data->val_out = mdio_read(mii_addr, data->phy_id, data->reg_num & 0x1f); + return 0; + case SIOCSMIIREG: /* Write MII PHY register. */ + mdio_write(mii_addr, data->phy_id, data->reg_num & 0x1f, data->val_in); + return 0; + } + return -EOPNOTSUPP; +} + +/*====================================================================*/ + +static void get_8390_hdr(struct net_device *dev, + struct e8390_pkt_hdr *hdr, + int ring_page) +{ + unsigned int nic_base = dev->base_addr; + + outb_p(0, nic_base + EN0_RSARLO); /* On page boundary */ + outb_p(ring_page, nic_base + EN0_RSARHI); + outb_p(E8390_RREAD+E8390_START, nic_base + AXNET_CMD); + + insw(nic_base + AXNET_DATAPORT, hdr, + sizeof(struct e8390_pkt_hdr)>>1); + /* Fix for big endian systems */ + hdr->count = le16_to_cpu(hdr->count); + +} + +/*====================================================================*/ + +static void block_input(struct net_device *dev, int count, + struct sk_buff *skb, int ring_offset) +{ + unsigned int nic_base = dev->base_addr; + struct ei_device *ei_local = netdev_priv(dev); + int xfer_count = count; + char *buf = skb->data; + + if ((netif_msg_rx_status(ei_local)) && (count != 4)) + netdev_dbg(dev, "[bi=%d]\n", count+4); + outb_p(ring_offset & 0xff, nic_base + EN0_RSARLO); + outb_p(ring_offset >> 8, nic_base + EN0_RSARHI); + outb_p(E8390_RREAD+E8390_START, nic_base + AXNET_CMD); + + insw(nic_base + AXNET_DATAPORT,buf,count>>1); + if (count & 0x01) { + buf[count-1] = inb(nic_base + AXNET_DATAPORT); + xfer_count++; + } + +} + +/*====================================================================*/ + +static void block_output(struct net_device *dev, int count, + const u_char *buf, const int start_page) +{ + unsigned int nic_base = dev->base_addr; + + pr_debug("%s: [bo=%d]\n", dev->name, count); + + /* Round the count up for word writes. Do we need to do this? + What effect will an odd byte count have on the 8390? + I should check someday. */ + if (count & 0x01) + count++; + + outb_p(0x00, nic_base + EN0_RSARLO); + outb_p(start_page, nic_base + EN0_RSARHI); + outb_p(E8390_RWRITE+E8390_START, nic_base + AXNET_CMD); + outsw(nic_base + AXNET_DATAPORT, buf, count>>1); +} + +static const struct pcmcia_device_id axnet_ids[] = { + PCMCIA_PFC_DEVICE_MANF_CARD(0, 0x016c, 0x0081), + PCMCIA_DEVICE_MANF_CARD(0x018a, 0x0301), + PCMCIA_DEVICE_MANF_CARD(0x01bf, 0x2328), + PCMCIA_DEVICE_MANF_CARD(0x026f, 0x0301), + PCMCIA_DEVICE_MANF_CARD(0x026f, 0x0303), + PCMCIA_DEVICE_MANF_CARD(0x026f, 0x0309), + PCMCIA_DEVICE_MANF_CARD(0x0274, 0x1106), + PCMCIA_DEVICE_MANF_CARD(0x8a01, 0xc1ab), + PCMCIA_DEVICE_MANF_CARD(0x021b, 0x0202), + PCMCIA_DEVICE_MANF_CARD(0xffff, 0x1090), + PCMCIA_DEVICE_PROD_ID12("AmbiCom,Inc.", "Fast Ethernet PC Card(AMB8110)", 0x49b020a7, 0x119cc9fc), + PCMCIA_DEVICE_PROD_ID124("Fast Ethernet", "16-bit PC Card", "AX88190", 0xb4be14e3, 0x9a12eb6a, 0xab9be5ef), + PCMCIA_DEVICE_PROD_ID12("ASIX", "AX88190", 0x0959823b, 0xab9be5ef), + PCMCIA_DEVICE_PROD_ID12("Billionton", "LNA-100B", 0x552ab682, 0xbc3b87e1), + PCMCIA_DEVICE_PROD_ID12("CHEETAH ETHERCARD", "EN2228", 0x00fa7bc8, 0x00e990cc), + PCMCIA_DEVICE_PROD_ID12("CNet", "CNF301", 0xbc477dde, 0x78c5f40b), + PCMCIA_DEVICE_PROD_ID12("corega K.K.", "corega FEther PCC-TXD", 0x5261440f, 0x436768c5), + PCMCIA_DEVICE_PROD_ID12("corega K.K.", "corega FEtherII PCC-TXD", 0x5261440f, 0x730df72e), + PCMCIA_DEVICE_PROD_ID12("corega K.K.", "corega FEther PCC-TXM", 0x5261440f, 0x3abbd061), + PCMCIA_DEVICE_PROD_ID12("Dynalink", "L100C16", 0x55632fd5, 0x66bc2a90), + PCMCIA_DEVICE_PROD_ID12("IO DATA", "ETXPCM", 0x547e66dc, 0x233adac2), + PCMCIA_DEVICE_PROD_ID12("Linksys", "EtherFast 10/100 PC Card (PCMPC100 V3)", 0x0733cc81, 0x232019a8), + PCMCIA_DEVICE_PROD_ID12("MELCO", "LPC3-TX", 0x481e0094, 0xf91af609), + PCMCIA_DEVICE_PROD_ID12("NETGEAR", "FA411", 0x9aa79dc3, 0x40fad875), + PCMCIA_DEVICE_PROD_ID12("PCMCIA", "100BASE", 0x281f1c5d, 0x7c2add04), + PCMCIA_DEVICE_PROD_ID12("PCMCIA", "FastEtherCard", 0x281f1c5d, 0x7ef26116), + PCMCIA_DEVICE_PROD_ID12("PCMCIA", "FEP501", 0x281f1c5d, 0x2e272058), + PCMCIA_DEVICE_PROD_ID14("Network Everywhere", "AX88190", 0x820a67b6, 0xab9be5ef), + PCMCIA_DEVICE_NULL, +}; +MODULE_DEVICE_TABLE(pcmcia, axnet_ids); + +static struct pcmcia_driver axnet_cs_driver = { + .owner = THIS_MODULE, + .name = "axnet_cs", + .probe = axnet_probe, + .remove = axnet_detach, + .id_table = axnet_ids, + .suspend = axnet_suspend, + .resume = axnet_resume, +}; +module_pcmcia_driver(axnet_cs_driver); + +/*====================================================================*/ + +/* 8390.c: A general NS8390 ethernet driver core for linux. */ +/* + Written 1992-94 by Donald Becker. + + Copyright 1993 United States Government as represented by the + Director, National Security Agency. + + This software may be used and distributed according to the terms + of the GNU General Public License, incorporated herein by reference. + + The author may be reached as becker@scyld.com, or C/O + Scyld Computing Corporation + 410 Severn Ave., Suite 210 + Annapolis MD 21403 + + This is the chip-specific code for many 8390-based ethernet adaptors. + This is not a complete driver, it must be combined with board-specific + code such as ne.c, wd.c, 3c503.c, etc. + + Seeing how at least eight drivers use this code, (not counting the + PCMCIA ones either) it is easy to break some card by what seems like + a simple innocent change. Please contact me or Donald if you think + you have found something that needs changing. -- PG + + Changelog: + + Paul Gortmaker : remove set_bit lock, other cleanups. + Paul Gortmaker : add ei_get_8390_hdr() so we can pass skb's to + ei_block_input() for eth_io_copy_and_sum(). + Paul Gortmaker : exchange static int ei_pingpong for a #define, + also add better Tx error handling. + Paul Gortmaker : rewrite Rx overrun handling as per NS specs. + Alexey Kuznetsov : use the 8390's six bit hash multicast filter. + Paul Gortmaker : tweak ANK's above multicast changes a bit. + Paul Gortmaker : update packet statistics for v2.1.x + Alan Cox : support arbitrary stupid port mappings on the + 68K Macintosh. Support >16bit I/O spaces + Paul Gortmaker : add kmod support for auto-loading of the 8390 + module by all drivers that require it. + Alan Cox : Spinlocking work, added 'BUG_83C690' + Paul Gortmaker : Separate out Tx timeout code from Tx path. + + Sources: + The National Semiconductor LAN Databook, and the 3Com 3c503 databook. + + */ + +#include <linux/bitops.h> +#include <asm/irq.h> +#include <linux/fcntl.h> +#include <linux/in.h> +#include <linux/interrupt.h> + +#define BUG_83C690 + +/* These are the operational function interfaces to board-specific + routines. + void reset_8390(struct net_device *dev) + Resets the board associated with DEV, including a hardware reset of + the 8390. This is only called when there is a transmit timeout, and + it is always followed by 8390_init(). + void block_output(struct net_device *dev, int count, const unsigned char *buf, + int start_page) + Write the COUNT bytes of BUF to the packet buffer at START_PAGE. The + "page" value uses the 8390's 256-byte pages. + void get_8390_hdr(struct net_device *dev, struct e8390_hdr *hdr, int ring_page) + Read the 4 byte, page aligned 8390 header. *If* there is a + subsequent read, it will be of the rest of the packet. + void block_input(struct net_device *dev, int count, struct sk_buff *skb, int ring_offset) + Read COUNT bytes from the packet buffer into the skb data area. Start + reading from RING_OFFSET, the address as the 8390 sees it. This will always + follow the read of the 8390 header. +*/ +#define ei_reset_8390 (ei_local->reset_8390) +#define ei_block_output (ei_local->block_output) +#define ei_block_input (ei_local->block_input) +#define ei_get_8390_hdr (ei_local->get_8390_hdr) + +/* Index to functions. */ +static void ei_tx_intr(struct net_device *dev); +static void ei_tx_err(struct net_device *dev); +static void ei_receive(struct net_device *dev); +static void ei_rx_overrun(struct net_device *dev); + +/* Routines generic to NS8390-based boards. */ +static void NS8390_trigger_send(struct net_device *dev, unsigned int length, + int start_page); +static void do_set_multicast_list(struct net_device *dev); + +/* + * SMP and the 8390 setup. + * + * The 8390 isn't exactly designed to be multithreaded on RX/TX. There is + * a page register that controls bank and packet buffer access. We guard + * this with ei_local->page_lock. Nobody should assume or set the page other + * than zero when the lock is not held. Lock holders must restore page 0 + * before unlocking. Even pure readers must take the lock to protect in + * page 0. + * + * To make life difficult the chip can also be very slow. We therefore can't + * just use spinlocks. For the longer lockups we disable the irq the device + * sits on and hold the lock. We must hold the lock because there is a dual + * processor case other than interrupts (get stats/set multicast list in + * parallel with each other and transmit). + * + * Note: in theory we can just disable the irq on the card _but_ there is + * a latency on SMP irq delivery. So we can easily go "disable irq" "sync irqs" + * enter lock, take the queued irq. So we waddle instead of flying. + * + * Finally by special arrangement for the purpose of being generally + * annoying the transmit function is called bh atomic. That places + * restrictions on the user context callers as disable_irq won't save + * them. + */ + +/** + * ax_open - Open/initialize the board. + * @dev: network device to initialize + * + * This routine goes all-out, setting everything + * up anew at each open, even though many of these registers should only + * need to be set once at boot. + */ +static int ax_open(struct net_device *dev) +{ + unsigned long flags; + struct ei_device *ei_local = netdev_priv(dev); + + /* + * Grab the page lock so we own the register set, then call + * the init function. + */ + + spin_lock_irqsave(&ei_local->page_lock, flags); + AX88190_init(dev, 1); + /* Set the flag before we drop the lock, That way the IRQ arrives + after its set and we get no silly warnings */ + netif_start_queue(dev); + spin_unlock_irqrestore(&ei_local->page_lock, flags); + ei_local->irqlock = 0; + return 0; +} + +#define dev_lock(dev) (((struct ei_device *)netdev_priv(dev))->page_lock) + +/** + * ax_close - shut down network device + * @dev: network device to close + * + * Opposite of ax_open(). Only used when "ifconfig <devname> down" is done. + */ +static int ax_close(struct net_device *dev) +{ + unsigned long flags; + + /* + * Hold the page lock during close + */ + + spin_lock_irqsave(&dev_lock(dev), flags); + AX88190_init(dev, 0); + spin_unlock_irqrestore(&dev_lock(dev), flags); + netif_stop_queue(dev); + return 0; +} + +/** + * axnet_tx_timeout - handle transmit time out condition + * @dev: network device which has apparently fallen asleep + * @txqueue: unused + * + * Called by kernel when device never acknowledges a transmit has + * completed (or failed) - i.e. never posted a Tx related interrupt. + */ + +static void axnet_tx_timeout(struct net_device *dev, unsigned int txqueue) +{ + long e8390_base = dev->base_addr; + struct ei_device *ei_local = netdev_priv(dev); + int txsr, isr, tickssofar = jiffies - dev_trans_start(dev); + unsigned long flags; + + dev->stats.tx_errors++; + + spin_lock_irqsave(&ei_local->page_lock, flags); + txsr = inb(e8390_base+EN0_TSR); + isr = inb(e8390_base+EN0_ISR); + spin_unlock_irqrestore(&ei_local->page_lock, flags); + + netdev_dbg(dev, "Tx timed out, %s TSR=%#2x, ISR=%#2x, t=%d.\n", + (txsr & ENTSR_ABT) ? "excess collisions." : + (isr) ? "lost interrupt?" : "cable problem?", + txsr, isr, tickssofar); + + if (!isr && !dev->stats.tx_packets) + { + /* The 8390 probably hasn't gotten on the cable yet. */ + ei_local->interface_num ^= 1; /* Try a different xcvr. */ + } + + /* Ugly but a reset can be slow, yet must be protected */ + + spin_lock_irqsave(&ei_local->page_lock, flags); + + /* Try to restart the card. Perhaps the user has fixed something. */ + ei_reset_8390(dev); + AX88190_init(dev, 1); + + spin_unlock_irqrestore(&ei_local->page_lock, flags); + netif_wake_queue(dev); +} + +/** + * axnet_start_xmit - begin packet transmission + * @skb: packet to be sent + * @dev: network device to which packet is sent + * + * Sends a packet to an 8390 network device. + */ + +static netdev_tx_t axnet_start_xmit(struct sk_buff *skb, + struct net_device *dev) +{ + long e8390_base = dev->base_addr; + struct ei_device *ei_local = netdev_priv(dev); + int length, send_length, output_page; + unsigned long flags; + u8 packet[ETH_ZLEN]; + + netif_stop_queue(dev); + + length = skb->len; + + /* Mask interrupts from the ethercard. + SMP: We have to grab the lock here otherwise the IRQ handler + on another CPU can flip window and race the IRQ mask set. We end + up trashing the mcast filter not disabling irqs if we don't lock */ + + spin_lock_irqsave(&ei_local->page_lock, flags); + outb_p(0x00, e8390_base + EN0_IMR); + + /* + * Slow phase with lock held. + */ + + ei_local->irqlock = 1; + + send_length = max(length, ETH_ZLEN); + + /* + * We have two Tx slots available for use. Find the first free + * slot, and then perform some sanity checks. With two Tx bufs, + * you get very close to transmitting back-to-back packets. With + * only one Tx buf, the transmitter sits idle while you reload the + * card, leaving a substantial gap between each transmitted packet. + */ + + if (ei_local->tx1 == 0) + { + output_page = ei_local->tx_start_page; + ei_local->tx1 = send_length; + if ((netif_msg_tx_queued(ei_local)) && + ei_local->tx2 > 0) + netdev_dbg(dev, + "idle transmitter tx2=%d, lasttx=%d, txing=%d\n", + ei_local->tx2, ei_local->lasttx, + ei_local->txing); + } + else if (ei_local->tx2 == 0) + { + output_page = ei_local->tx_start_page + TX_PAGES/2; + ei_local->tx2 = send_length; + if ((netif_msg_tx_queued(ei_local)) && + ei_local->tx1 > 0) + netdev_dbg(dev, + "idle transmitter, tx1=%d, lasttx=%d, txing=%d\n", + ei_local->tx1, ei_local->lasttx, + ei_local->txing); + } + else + { /* We should never get here. */ + netif_dbg(ei_local, tx_err, dev, + "No Tx buffers free! tx1=%d tx2=%d last=%d\n", + ei_local->tx1, ei_local->tx2, + ei_local->lasttx); + ei_local->irqlock = 0; + netif_stop_queue(dev); + outb_p(ENISR_ALL, e8390_base + EN0_IMR); + spin_unlock_irqrestore(&ei_local->page_lock, flags); + dev->stats.tx_errors++; + return NETDEV_TX_BUSY; + } + + /* + * Okay, now upload the packet and trigger a send if the transmitter + * isn't already sending. If it is busy, the interrupt handler will + * trigger the send later, upon receiving a Tx done interrupt. + */ + + if (length == skb->len) + ei_block_output(dev, length, skb->data, output_page); + else { + memset(packet, 0, ETH_ZLEN); + skb_copy_from_linear_data(skb, packet, skb->len); + ei_block_output(dev, length, packet, output_page); + } + + if (! ei_local->txing) + { + ei_local->txing = 1; + NS8390_trigger_send(dev, send_length, output_page); + netif_trans_update(dev); + if (output_page == ei_local->tx_start_page) + { + ei_local->tx1 = -1; + ei_local->lasttx = -1; + } + else + { + ei_local->tx2 = -1; + ei_local->lasttx = -2; + } + } + else ei_local->txqueue++; + + if (ei_local->tx1 && ei_local->tx2) + netif_stop_queue(dev); + else + netif_start_queue(dev); + + /* Turn 8390 interrupts back on. */ + ei_local->irqlock = 0; + outb_p(ENISR_ALL, e8390_base + EN0_IMR); + + spin_unlock_irqrestore(&ei_local->page_lock, flags); + + dev_kfree_skb (skb); + dev->stats.tx_bytes += send_length; + + return NETDEV_TX_OK; +} + +/** + * ax_interrupt - handle the interrupts from an 8390 + * @irq: interrupt number + * @dev_id: a pointer to the net_device + * + * Handle the ether interface interrupts. We pull packets from + * the 8390 via the card specific functions and fire them at the networking + * stack. We also handle transmit completions and wake the transmit path if + * necessary. We also update the counters and do other housekeeping as + * needed. + */ + +static irqreturn_t ax_interrupt(int irq, void *dev_id) +{ + struct net_device *dev = dev_id; + long e8390_base; + int interrupts, nr_serviced = 0, i; + struct ei_device *ei_local; + int handled = 0; + unsigned long flags; + + e8390_base = dev->base_addr; + ei_local = netdev_priv(dev); + + /* + * Protect the irq test too. + */ + + spin_lock_irqsave(&ei_local->page_lock, flags); + + if (ei_local->irqlock) { +#if 1 /* This might just be an interrupt for a PCI device sharing this line */ + const char *msg; + /* The "irqlock" check is only for testing. */ + if (ei_local->irqlock) + msg = "Interrupted while interrupts are masked!"; + else + msg = "Reentering the interrupt handler!"; + netdev_info(dev, "%s, isr=%#2x imr=%#2x\n", + msg, + inb_p(e8390_base + EN0_ISR), + inb_p(e8390_base + EN0_IMR)); +#endif + spin_unlock_irqrestore(&ei_local->page_lock, flags); + return IRQ_NONE; + } + + netif_dbg(ei_local, intr, dev, "interrupt(isr=%#2.2x)\n", + inb_p(e8390_base + EN0_ISR)); + + outb_p(0x00, e8390_base + EN0_ISR); + ei_local->irqlock = 1; + + /* !!Assumption!! -- we stay in page 0. Don't break this. */ + while ((interrupts = inb_p(e8390_base + EN0_ISR)) != 0 && + ++nr_serviced < MAX_SERVICE) + { + if (!netif_running(dev) || (interrupts == 0xff)) { + netif_warn(ei_local, intr, dev, + "interrupt from stopped card\n"); + outb_p(interrupts, e8390_base + EN0_ISR); + interrupts = 0; + break; + } + handled = 1; + + /* AX88190 bug fix. */ + outb_p(interrupts, e8390_base + EN0_ISR); + for (i = 0; i < 10; i++) { + if (!(inb(e8390_base + EN0_ISR) & interrupts)) + break; + outb_p(0, e8390_base + EN0_ISR); + outb_p(interrupts, e8390_base + EN0_ISR); + } + if (interrupts & ENISR_OVER) + ei_rx_overrun(dev); + else if (interrupts & (ENISR_RX+ENISR_RX_ERR)) + { + /* Got a good (?) packet. */ + ei_receive(dev); + } + /* Push the next to-transmit packet through. */ + if (interrupts & ENISR_TX) + ei_tx_intr(dev); + else if (interrupts & ENISR_TX_ERR) + ei_tx_err(dev); + + if (interrupts & ENISR_COUNTERS) + { + dev->stats.rx_frame_errors += inb_p(e8390_base + EN0_COUNTER0); + dev->stats.rx_crc_errors += inb_p(e8390_base + EN0_COUNTER1); + dev->stats.rx_missed_errors+= inb_p(e8390_base + EN0_COUNTER2); + } + } + + if (interrupts && (netif_msg_intr(ei_local))) + { + handled = 1; + if (nr_serviced >= MAX_SERVICE) + { + /* 0xFF is valid for a card removal */ + if (interrupts != 0xFF) + netdev_warn(dev, + "Too much work at interrupt, status %#2.2x\n", + interrupts); + outb_p(ENISR_ALL, e8390_base + EN0_ISR); /* Ack. most intrs. */ + } else { + netdev_warn(dev, "unknown interrupt %#2x\n", + interrupts); + outb_p(0xff, e8390_base + EN0_ISR); /* Ack. all intrs. */ + } + } + + /* Turn 8390 interrupts back on. */ + ei_local->irqlock = 0; + outb_p(ENISR_ALL, e8390_base + EN0_IMR); + + spin_unlock_irqrestore(&ei_local->page_lock, flags); + return IRQ_RETVAL(handled); +} + +/** + * ei_tx_err - handle transmitter error + * @dev: network device which threw the exception + * + * A transmitter error has happened. Most likely excess collisions (which + * is a fairly normal condition). If the error is one where the Tx will + * have been aborted, we try and send another one right away, instead of + * letting the failed packet sit and collect dust in the Tx buffer. This + * is a much better solution as it avoids kernel based Tx timeouts, and + * an unnecessary card reset. + * + * Called with lock held. + */ + +static void ei_tx_err(struct net_device *dev) +{ + long e8390_base = dev->base_addr; + unsigned char txsr = inb_p(e8390_base+EN0_TSR); + unsigned char tx_was_aborted = txsr & (ENTSR_ABT+ENTSR_FU); + +#ifdef VERBOSE_ERROR_DUMP + netdev_dbg(dev, "transmitter error (%#2x):", txsr); + if (txsr & ENTSR_ABT) + pr_cont(" excess-collisions"); + if (txsr & ENTSR_ND) + pr_cont(" non-deferral"); + if (txsr & ENTSR_CRS) + pr_cont(" lost-carrier"); + if (txsr & ENTSR_FU) + pr_cont(" FIFO-underrun"); + if (txsr & ENTSR_CDH) + pr_cont(" lost-heartbeat"); + pr_cont("\n"); +#endif + + if (tx_was_aborted) + ei_tx_intr(dev); + else + { + dev->stats.tx_errors++; + if (txsr & ENTSR_CRS) dev->stats.tx_carrier_errors++; + if (txsr & ENTSR_CDH) dev->stats.tx_heartbeat_errors++; + if (txsr & ENTSR_OWC) dev->stats.tx_window_errors++; + } +} + +/** + * ei_tx_intr - transmit interrupt handler + * @dev: network device for which tx intr is handled + * + * We have finished a transmit: check for errors and then trigger the next + * packet to be sent. Called with lock held. + */ + +static void ei_tx_intr(struct net_device *dev) +{ + long e8390_base = dev->base_addr; + struct ei_device *ei_local = netdev_priv(dev); + int status = inb(e8390_base + EN0_TSR); + + /* + * There are two Tx buffers, see which one finished, and trigger + * the send of another one if it exists. + */ + ei_local->txqueue--; + + if (ei_local->tx1 < 0) + { + if (ei_local->lasttx != 1 && ei_local->lasttx != -1) + netdev_err(dev, "%s: bogus last_tx_buffer %d, tx1=%d\n", + ei_local->name, ei_local->lasttx, + ei_local->tx1); + ei_local->tx1 = 0; + if (ei_local->tx2 > 0) + { + ei_local->txing = 1; + NS8390_trigger_send(dev, ei_local->tx2, ei_local->tx_start_page + 6); + netif_trans_update(dev); + ei_local->tx2 = -1; + ei_local->lasttx = 2; + } else { + ei_local->lasttx = 20; + ei_local->txing = 0; + } + } + else if (ei_local->tx2 < 0) + { + if (ei_local->lasttx != 2 && ei_local->lasttx != -2) + netdev_err(dev, "%s: bogus last_tx_buffer %d, tx2=%d\n", + ei_local->name, ei_local->lasttx, + ei_local->tx2); + ei_local->tx2 = 0; + if (ei_local->tx1 > 0) + { + ei_local->txing = 1; + NS8390_trigger_send(dev, ei_local->tx1, ei_local->tx_start_page); + netif_trans_update(dev); + ei_local->tx1 = -1; + ei_local->lasttx = 1; + } else { + ei_local->lasttx = 10; + ei_local->txing = 0; + } + } +// else +// netdev_warn(dev, "unexpected TX-done interrupt, lasttx=%d\n", +// ei_local->lasttx); + + /* Minimize Tx latency: update the statistics after we restart TXing. */ + if (status & ENTSR_COL) + dev->stats.collisions++; + if (status & ENTSR_PTX) + dev->stats.tx_packets++; + else + { + dev->stats.tx_errors++; + if (status & ENTSR_ABT) + { + dev->stats.tx_aborted_errors++; + dev->stats.collisions += 16; + } + if (status & ENTSR_CRS) + dev->stats.tx_carrier_errors++; + if (status & ENTSR_FU) + dev->stats.tx_fifo_errors++; + if (status & ENTSR_CDH) + dev->stats.tx_heartbeat_errors++; + if (status & ENTSR_OWC) + dev->stats.tx_window_errors++; + } + netif_wake_queue(dev); +} + +/** + * ei_receive - receive some packets + * @dev: network device with which receive will be run + * + * We have a good packet(s), get it/them out of the buffers. + * Called with lock held. + */ + +static void ei_receive(struct net_device *dev) +{ + long e8390_base = dev->base_addr; + struct ei_device *ei_local = netdev_priv(dev); + unsigned char rxing_page, this_frame, next_frame; + unsigned short current_offset; + int rx_pkt_count = 0; + struct e8390_pkt_hdr rx_frame; + + while (++rx_pkt_count < 10) + { + int pkt_len, pkt_stat; + + /* Get the rx page (incoming packet pointer). */ + rxing_page = inb_p(e8390_base + EN1_CURPAG -1); + + /* Remove one frame from the ring. Boundary is always a page behind. */ + this_frame = inb_p(e8390_base + EN0_BOUNDARY) + 1; + if (this_frame >= ei_local->stop_page) + this_frame = ei_local->rx_start_page; + + /* Someday we'll omit the previous, iff we never get this message. + (There is at least one clone claimed to have a problem.) + + Keep quiet if it looks like a card removal. One problem here + is that some clones crash in roughly the same way. + */ + if ((netif_msg_rx_err(ei_local)) && + this_frame != ei_local->current_page && + (this_frame != 0x0 || rxing_page != 0xFF)) + netdev_err(dev, "mismatched read page pointers %2x vs %2x\n", + this_frame, ei_local->current_page); + + if (this_frame == rxing_page) /* Read all the frames? */ + break; /* Done for now */ + + current_offset = this_frame << 8; + ei_get_8390_hdr(dev, &rx_frame, this_frame); + + pkt_len = rx_frame.count - sizeof(struct e8390_pkt_hdr); + pkt_stat = rx_frame.status; + + next_frame = this_frame + 1 + ((pkt_len+4)>>8); + + if (pkt_len < 60 || pkt_len > 1518) + { + netif_err(ei_local, rx_err, dev, + "bogus packet size: %d, status=%#2x nxpg=%#2x\n", + rx_frame.count, rx_frame.status, + rx_frame.next); + dev->stats.rx_errors++; + dev->stats.rx_length_errors++; + } + else if ((pkt_stat & 0x0F) == ENRSR_RXOK) + { + struct sk_buff *skb; + + skb = netdev_alloc_skb(dev, pkt_len + 2); + if (skb == NULL) + { + netif_err(ei_local, rx_err, dev, + "Couldn't allocate a sk_buff of size %d\n", + pkt_len); + dev->stats.rx_dropped++; + break; + } + else + { + skb_reserve(skb,2); /* IP headers on 16 byte boundaries */ + skb_put(skb, pkt_len); /* Make room */ + ei_block_input(dev, pkt_len, skb, current_offset + sizeof(rx_frame)); + skb->protocol=eth_type_trans(skb,dev); + netif_rx(skb); + dev->stats.rx_packets++; + dev->stats.rx_bytes += pkt_len; + if (pkt_stat & ENRSR_PHY) + dev->stats.multicast++; + } + } + else + { + netif_err(ei_local, rx_err, dev, + "bogus packet: status=%#2x nxpg=%#2x size=%d\n", + rx_frame.status, rx_frame.next, + rx_frame.count); + dev->stats.rx_errors++; + /* NB: The NIC counts CRC, frame and missed errors. */ + if (pkt_stat & ENRSR_FO) + dev->stats.rx_fifo_errors++; + } + next_frame = rx_frame.next; + + /* This _should_ never happen: it's here for avoiding bad clones. */ + if (next_frame >= ei_local->stop_page) { + netdev_info(dev, "next frame inconsistency, %#2x\n", + next_frame); + next_frame = ei_local->rx_start_page; + } + ei_local->current_page = next_frame; + outb_p(next_frame-1, e8390_base+EN0_BOUNDARY); + } +} + +/** + * ei_rx_overrun - handle receiver overrun + * @dev: network device which threw exception + * + * We have a receiver overrun: we have to kick the 8390 to get it started + * again. Problem is that you have to kick it exactly as NS prescribes in + * the updated datasheets, or "the NIC may act in an unpredictable manner." + * This includes causing "the NIC to defer indefinitely when it is stopped + * on a busy network." Ugh. + * Called with lock held. Don't call this with the interrupts off or your + * computer will hate you - it takes 10ms or so. + */ + +static void ei_rx_overrun(struct net_device *dev) +{ + struct axnet_dev *info = PRIV(dev); + long e8390_base = dev->base_addr; + unsigned char was_txing, must_resend = 0; + struct ei_device *ei_local = netdev_priv(dev); + + /* + * Record whether a Tx was in progress and then issue the + * stop command. + */ + was_txing = inb_p(e8390_base+E8390_CMD) & E8390_TRANS; + outb_p(E8390_NODMA+E8390_PAGE0+E8390_STOP, e8390_base+E8390_CMD); + + netif_dbg(ei_local, rx_err, dev, "Receiver overrun\n"); + dev->stats.rx_over_errors++; + + /* + * Wait a full Tx time (1.2ms) + some guard time, NS says 1.6ms total. + * We wait at least 2ms. + */ + + mdelay(2); + + /* + * Reset RBCR[01] back to zero as per magic incantation. + */ + outb_p(0x00, e8390_base+EN0_RCNTLO); + outb_p(0x00, e8390_base+EN0_RCNTHI); + + /* + * See if any Tx was interrupted or not. According to NS, this + * step is vital, and skipping it will cause no end of havoc. + */ + + if (was_txing) + { + unsigned char tx_completed = inb_p(e8390_base+EN0_ISR) & (ENISR_TX+ENISR_TX_ERR); + if (!tx_completed) + must_resend = 1; + } + + /* + * Have to enter loopback mode and then restart the NIC before + * you are allowed to slurp packets up off the ring. + */ + outb_p(E8390_TXOFF, e8390_base + EN0_TXCR); + outb_p(E8390_NODMA + E8390_PAGE0 + E8390_START, e8390_base + E8390_CMD); + + /* + * Clear the Rx ring of all the debris, and ack the interrupt. + */ + ei_receive(dev); + + /* + * Leave loopback mode, and resend any packet that got stopped. + */ + outb_p(E8390_TXCONFIG | info->duplex_flag, e8390_base + EN0_TXCR); + if (must_resend) + outb_p(E8390_NODMA + E8390_PAGE0 + E8390_START + E8390_TRANS, e8390_base + E8390_CMD); +} + +/* + * Collect the stats. This is called unlocked and from several contexts. + */ + +static struct net_device_stats *get_stats(struct net_device *dev) +{ + long ioaddr = dev->base_addr; + struct ei_device *ei_local = netdev_priv(dev); + unsigned long flags; + + /* If the card is stopped, just return the present stats. */ + if (!netif_running(dev)) + return &dev->stats; + + spin_lock_irqsave(&ei_local->page_lock,flags); + /* Read the counter registers, assuming we are in page 0. */ + dev->stats.rx_frame_errors += inb_p(ioaddr + EN0_COUNTER0); + dev->stats.rx_crc_errors += inb_p(ioaddr + EN0_COUNTER1); + dev->stats.rx_missed_errors+= inb_p(ioaddr + EN0_COUNTER2); + spin_unlock_irqrestore(&ei_local->page_lock, flags); + + return &dev->stats; +} + +/* + * Form the 64 bit 8390 multicast table from the linked list of addresses + * associated with this dev structure. + */ + +static inline void make_mc_bits(u8 *bits, struct net_device *dev) +{ + struct netdev_hw_addr *ha; + u32 crc; + + netdev_for_each_mc_addr(ha, dev) { + crc = ether_crc(ETH_ALEN, ha->addr); + /* + * The 8390 uses the 6 most significant bits of the + * CRC to index the multicast table. + */ + bits[crc>>29] |= (1<<((crc>>26)&7)); + } +} + +/** + * do_set_multicast_list - set/clear multicast filter + * @dev: net device for which multicast filter is adjusted + * + * Set or clear the multicast filter for this adaptor. + * Must be called with lock held. + */ + +static void do_set_multicast_list(struct net_device *dev) +{ + long e8390_base = dev->base_addr; + int i; + struct ei_device *ei_local = netdev_priv(dev); + + if (!(dev->flags&(IFF_PROMISC|IFF_ALLMULTI))) { + memset(ei_local->mcfilter, 0, 8); + if (!netdev_mc_empty(dev)) + make_mc_bits(ei_local->mcfilter, dev); + } else { + /* set to accept-all */ + memset(ei_local->mcfilter, 0xFF, 8); + } + + outb_p(E8390_NODMA + E8390_PAGE1, e8390_base + E8390_CMD); + for(i = 0; i < 8; i++) + { + outb_p(ei_local->mcfilter[i], e8390_base + EN1_MULT_SHIFT(i)); + } + outb_p(E8390_NODMA + E8390_PAGE0, e8390_base + E8390_CMD); + + if(dev->flags&IFF_PROMISC) + outb_p(E8390_RXCONFIG | 0x58, e8390_base + EN0_RXCR); + else if (dev->flags & IFF_ALLMULTI || !netdev_mc_empty(dev)) + outb_p(E8390_RXCONFIG | 0x48, e8390_base + EN0_RXCR); + else + outb_p(E8390_RXCONFIG | 0x40, e8390_base + EN0_RXCR); + + outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, e8390_base+E8390_CMD); +} + +/* + * Called without lock held. This is invoked from user context and may + * be parallel to just about everything else. Its also fairly quick and + * not called too often. Must protect against both bh and irq users + */ + +static void set_multicast_list(struct net_device *dev) +{ + unsigned long flags; + + spin_lock_irqsave(&dev_lock(dev), flags); + do_set_multicast_list(dev); + spin_unlock_irqrestore(&dev_lock(dev), flags); +} + +/* This page of functions should be 8390 generic */ +/* Follow National Semi's recommendations for initializing the "NIC". */ + +/** + * AX88190_init - initialize 8390 hardware + * @dev: network device to initialize + * @startp: boolean. non-zero value to initiate chip processing + * + * Must be called with lock held. + */ + +static void AX88190_init(struct net_device *dev, int startp) +{ + struct axnet_dev *info = PRIV(dev); + long e8390_base = dev->base_addr; + struct ei_device *ei_local = netdev_priv(dev); + int i; + int endcfg = ei_local->word16 ? (0x48 | ENDCFG_WTS) : 0x48; + + if(sizeof(struct e8390_pkt_hdr)!=4) + panic("8390.c: header struct mispacked\n"); + /* Follow National Semi's recommendations for initing the DP83902. */ + outb_p(E8390_NODMA+E8390_PAGE0+E8390_STOP, e8390_base+E8390_CMD); /* 0x21 */ + outb_p(endcfg, e8390_base + EN0_DCFG); /* 0x48 or 0x49 */ + /* Clear the remote byte count registers. */ + outb_p(0x00, e8390_base + EN0_RCNTLO); + outb_p(0x00, e8390_base + EN0_RCNTHI); + /* Set to monitor and loopback mode -- this is vital!. */ + outb_p(E8390_RXOFF|0x40, e8390_base + EN0_RXCR); /* 0x60 */ + outb_p(E8390_TXOFF, e8390_base + EN0_TXCR); /* 0x02 */ + /* Set the transmit page and receive ring. */ + outb_p(ei_local->tx_start_page, e8390_base + EN0_TPSR); + ei_local->tx1 = ei_local->tx2 = 0; + outb_p(ei_local->rx_start_page, e8390_base + EN0_STARTPG); + outb_p(ei_local->stop_page-1, e8390_base + EN0_BOUNDARY); /* 3c503 says 0x3f,NS0x26*/ + ei_local->current_page = ei_local->rx_start_page; /* assert boundary+1 */ + outb_p(ei_local->stop_page, e8390_base + EN0_STOPPG); + /* Clear the pending interrupts and mask. */ + outb_p(0xFF, e8390_base + EN0_ISR); + outb_p(0x00, e8390_base + EN0_IMR); + + /* Copy the station address into the DS8390 registers. */ + + outb_p(E8390_NODMA + E8390_PAGE1 + E8390_STOP, e8390_base+E8390_CMD); /* 0x61 */ + for(i = 0; i < 6; i++) + { + outb_p(dev->dev_addr[i], e8390_base + EN1_PHYS_SHIFT(i)); + if(inb_p(e8390_base + EN1_PHYS_SHIFT(i))!=dev->dev_addr[i]) + netdev_err(dev, "Hw. address read/write mismap %d\n", i); + } + + outb_p(ei_local->rx_start_page, e8390_base + EN1_CURPAG); + outb_p(E8390_NODMA+E8390_PAGE0+E8390_STOP, e8390_base+E8390_CMD); + + netif_start_queue(dev); + ei_local->tx1 = ei_local->tx2 = 0; + ei_local->txing = 0; + + if (info->flags & IS_AX88790) /* select Internal PHY */ + outb(0x10, e8390_base + AXNET_GPIO); + + if (startp) + { + outb_p(0xff, e8390_base + EN0_ISR); + outb_p(ENISR_ALL, e8390_base + EN0_IMR); + outb_p(E8390_NODMA+E8390_PAGE0+E8390_START, e8390_base+E8390_CMD); + outb_p(E8390_TXCONFIG | info->duplex_flag, + e8390_base + EN0_TXCR); /* xmit on. */ + /* 3c503 TechMan says rxconfig only after the NIC is started. */ + outb_p(E8390_RXCONFIG | 0x40, e8390_base + EN0_RXCR); /* rx on, */ + do_set_multicast_list(dev); /* (re)load the mcast table */ + } +} + +/* Trigger a transmit start, assuming the length is valid. + Always called with the page lock held */ + +static void NS8390_trigger_send(struct net_device *dev, unsigned int length, + int start_page) +{ + long e8390_base = dev->base_addr; + struct ei_device *ei_local __attribute((unused)) = netdev_priv(dev); + + if (inb_p(e8390_base) & E8390_TRANS) + { + netdev_warn(dev, "trigger_send() called with the transmitter busy\n"); + return; + } + outb_p(length & 0xff, e8390_base + EN0_TCNTLO); + outb_p(length >> 8, e8390_base + EN0_TCNTHI); + outb_p(start_page, e8390_base + EN0_TPSR); + outb_p(E8390_NODMA+E8390_TRANS+E8390_START, e8390_base+E8390_CMD); +} |