diff options
Diffstat (limited to 'drivers/net/ethernet/marvell/skge.c')
| -rw-r--r-- | drivers/net/ethernet/marvell/skge.c | 4195 |
1 files changed, 4195 insertions, 0 deletions
diff --git a/drivers/net/ethernet/marvell/skge.c b/drivers/net/ethernet/marvell/skge.c new file mode 100644 index 000000000..1b43704ba --- /dev/null +++ b/drivers/net/ethernet/marvell/skge.c @@ -0,0 +1,4195 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * New driver for Marvell Yukon chipset and SysKonnect Gigabit + * Ethernet adapters. Based on earlier sk98lin, e100 and + * FreeBSD if_sk drivers. + * + * This driver intentionally does not support all the features + * of the original driver such as link fail-over and link management because + * those should be done at higher levels. + * + * Copyright (C) 2004, 2005 Stephen Hemminger <shemminger@osdl.org> + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/in.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/moduleparam.h> +#include <linux/netdevice.h> +#include <linux/etherdevice.h> +#include <linux/ethtool.h> +#include <linux/pci.h> +#include <linux/if_vlan.h> +#include <linux/ip.h> +#include <linux/delay.h> +#include <linux/crc32.h> +#include <linux/dma-mapping.h> +#include <linux/debugfs.h> +#include <linux/sched.h> +#include <linux/seq_file.h> +#include <linux/mii.h> +#include <linux/slab.h> +#include <linux/dmi.h> +#include <linux/prefetch.h> +#include <asm/irq.h> + +#include "skge.h" + +#define DRV_NAME "skge" +#define DRV_VERSION "1.14" + +#define DEFAULT_TX_RING_SIZE 128 +#define DEFAULT_RX_RING_SIZE 512 +#define MAX_TX_RING_SIZE 1024 +#define TX_LOW_WATER (MAX_SKB_FRAGS + 1) +#define MAX_RX_RING_SIZE 4096 +#define RX_COPY_THRESHOLD 128 +#define RX_BUF_SIZE 1536 +#define PHY_RETRIES 1000 +#define ETH_JUMBO_MTU 9000 +#define TX_WATCHDOG (5 * HZ) +#define BLINK_MS 250 +#define LINK_HZ HZ + +#define SKGE_EEPROM_MAGIC 0x9933aabb + + +MODULE_DESCRIPTION("SysKonnect Gigabit Ethernet driver"); +MODULE_AUTHOR("Stephen Hemminger <shemminger@linux-foundation.org>"); +MODULE_LICENSE("GPL"); +MODULE_VERSION(DRV_VERSION); + +static const u32 default_msg = (NETIF_MSG_DRV | NETIF_MSG_PROBE | + NETIF_MSG_LINK | NETIF_MSG_IFUP | + NETIF_MSG_IFDOWN); + +static int debug = -1; /* defaults above */ +module_param(debug, int, 0); +MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); + +static const struct pci_device_id skge_id_table[] = { + { PCI_DEVICE(PCI_VENDOR_ID_3COM, 0x1700) }, /* 3Com 3C940 */ + { PCI_DEVICE(PCI_VENDOR_ID_3COM, 0x80EB) }, /* 3Com 3C940B */ +#ifdef CONFIG_SKGE_GENESIS + { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x4300) }, /* SK-9xx */ +#endif + { PCI_DEVICE(PCI_VENDOR_ID_SYSKONNECT, 0x4320) }, /* SK-98xx V2.0 */ + { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4b01) }, /* D-Link DGE-530T (rev.B) */ + { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4c00) }, /* D-Link DGE-530T */ + { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4302) }, /* D-Link DGE-530T Rev C1 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4320) }, /* Marvell Yukon 88E8001/8003/8010 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x5005) }, /* Belkin */ + { PCI_DEVICE(PCI_VENDOR_ID_CNET, 0x434E) }, /* CNet PowerG-2000 */ + { PCI_DEVICE(PCI_VENDOR_ID_LINKSYS, 0x1064) }, /* Linksys EG1064 v2 */ + { PCI_VENDOR_ID_LINKSYS, 0x1032, PCI_ANY_ID, 0x0015 }, /* Linksys EG1032 v2 */ + { 0 } +}; +MODULE_DEVICE_TABLE(pci, skge_id_table); + +static int skge_up(struct net_device *dev); +static int skge_down(struct net_device *dev); +static void skge_phy_reset(struct skge_port *skge); +static void skge_tx_clean(struct net_device *dev); +static int xm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val); +static int gm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val); +static void genesis_get_stats(struct skge_port *skge, u64 *data); +static void yukon_get_stats(struct skge_port *skge, u64 *data); +static void yukon_init(struct skge_hw *hw, int port); +static void genesis_mac_init(struct skge_hw *hw, int port); +static void genesis_link_up(struct skge_port *skge); +static void skge_set_multicast(struct net_device *dev); +static irqreturn_t skge_intr(int irq, void *dev_id); + +/* Avoid conditionals by using array */ +static const int txqaddr[] = { Q_XA1, Q_XA2 }; +static const int rxqaddr[] = { Q_R1, Q_R2 }; +static const u32 rxirqmask[] = { IS_R1_F, IS_R2_F }; +static const u32 txirqmask[] = { IS_XA1_F, IS_XA2_F }; +static const u32 napimask[] = { IS_R1_F|IS_XA1_F, IS_R2_F|IS_XA2_F }; +static const u32 portmask[] = { IS_PORT_1, IS_PORT_2 }; + +static inline bool is_genesis(const struct skge_hw *hw) +{ +#ifdef CONFIG_SKGE_GENESIS + return hw->chip_id == CHIP_ID_GENESIS; +#else + return false; +#endif +} + +static int skge_get_regs_len(struct net_device *dev) +{ + return 0x4000; +} + +/* + * Returns copy of whole control register region + * Note: skip RAM address register because accessing it will + * cause bus hangs! + */ +static void skge_get_regs(struct net_device *dev, struct ethtool_regs *regs, + void *p) +{ + const struct skge_port *skge = netdev_priv(dev); + const void __iomem *io = skge->hw->regs; + + regs->version = 1; + memset(p, 0, regs->len); + memcpy_fromio(p, io, B3_RAM_ADDR); + + if (regs->len > B3_RI_WTO_R1) { + memcpy_fromio(p + B3_RI_WTO_R1, io + B3_RI_WTO_R1, + regs->len - B3_RI_WTO_R1); + } +} + +/* Wake on Lan only supported on Yukon chips with rev 1 or above */ +static u32 wol_supported(const struct skge_hw *hw) +{ + if (is_genesis(hw)) + return 0; + + if (hw->chip_id == CHIP_ID_YUKON && hw->chip_rev == 0) + return 0; + + return WAKE_MAGIC | WAKE_PHY; +} + +static void skge_wol_init(struct skge_port *skge) +{ + struct skge_hw *hw = skge->hw; + int port = skge->port; + u16 ctrl; + + skge_write16(hw, B0_CTST, CS_RST_CLR); + skge_write16(hw, SK_REG(port, GMAC_LINK_CTRL), GMLC_RST_CLR); + + /* Turn on Vaux */ + skge_write8(hw, B0_POWER_CTRL, + PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_ON | PC_VCC_OFF); + + /* WA code for COMA mode -- clear PHY reset */ + if (hw->chip_id == CHIP_ID_YUKON_LITE && + hw->chip_rev >= CHIP_REV_YU_LITE_A3) { + u32 reg = skge_read32(hw, B2_GP_IO); + reg |= GP_DIR_9; + reg &= ~GP_IO_9; + skge_write32(hw, B2_GP_IO, reg); + } + + skge_write32(hw, SK_REG(port, GPHY_CTRL), + GPC_DIS_SLEEP | + GPC_HWCFG_M_3 | GPC_HWCFG_M_2 | GPC_HWCFG_M_1 | GPC_HWCFG_M_0 | + GPC_ANEG_1 | GPC_RST_SET); + + skge_write32(hw, SK_REG(port, GPHY_CTRL), + GPC_DIS_SLEEP | + GPC_HWCFG_M_3 | GPC_HWCFG_M_2 | GPC_HWCFG_M_1 | GPC_HWCFG_M_0 | + GPC_ANEG_1 | GPC_RST_CLR); + + skge_write32(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR); + + /* Force to 10/100 skge_reset will re-enable on resume */ + gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, + (PHY_AN_100FULL | PHY_AN_100HALF | + PHY_AN_10FULL | PHY_AN_10HALF | PHY_AN_CSMA)); + /* no 1000 HD/FD */ + gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, 0); + gm_phy_write(hw, port, PHY_MARV_CTRL, + PHY_CT_RESET | PHY_CT_SPS_LSB | PHY_CT_ANE | + PHY_CT_RE_CFG | PHY_CT_DUP_MD); + + + /* Set GMAC to no flow control and auto update for speed/duplex */ + gma_write16(hw, port, GM_GP_CTRL, + GM_GPCR_FC_TX_DIS|GM_GPCR_TX_ENA|GM_GPCR_RX_ENA| + GM_GPCR_DUP_FULL|GM_GPCR_FC_RX_DIS|GM_GPCR_AU_FCT_DIS); + + /* Set WOL address */ + memcpy_toio(hw->regs + WOL_REGS(port, WOL_MAC_ADDR), + skge->netdev->dev_addr, ETH_ALEN); + + /* Turn on appropriate WOL control bits */ + skge_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), WOL_CTL_CLEAR_RESULT); + ctrl = 0; + if (skge->wol & WAKE_PHY) + ctrl |= WOL_CTL_ENA_PME_ON_LINK_CHG|WOL_CTL_ENA_LINK_CHG_UNIT; + else + ctrl |= WOL_CTL_DIS_PME_ON_LINK_CHG|WOL_CTL_DIS_LINK_CHG_UNIT; + + if (skge->wol & WAKE_MAGIC) + ctrl |= WOL_CTL_ENA_PME_ON_MAGIC_PKT|WOL_CTL_ENA_MAGIC_PKT_UNIT; + else + ctrl |= WOL_CTL_DIS_PME_ON_MAGIC_PKT|WOL_CTL_DIS_MAGIC_PKT_UNIT; + + ctrl |= WOL_CTL_DIS_PME_ON_PATTERN|WOL_CTL_DIS_PATTERN_UNIT; + skge_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), ctrl); + + /* block receiver */ + skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET); +} + +static void skge_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol) +{ + struct skge_port *skge = netdev_priv(dev); + + wol->supported = wol_supported(skge->hw); + wol->wolopts = skge->wol; +} + +static int skge_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol) +{ + struct skge_port *skge = netdev_priv(dev); + struct skge_hw *hw = skge->hw; + + if ((wol->wolopts & ~wol_supported(hw)) || + !device_can_wakeup(&hw->pdev->dev)) + return -EOPNOTSUPP; + + skge->wol = wol->wolopts; + + device_set_wakeup_enable(&hw->pdev->dev, skge->wol); + + return 0; +} + +/* Determine supported/advertised modes based on hardware. + * Note: ethtool ADVERTISED_xxx == SUPPORTED_xxx + */ +static u32 skge_supported_modes(const struct skge_hw *hw) +{ + u32 supported; + + if (hw->copper) { + supported = (SUPPORTED_10baseT_Half | + SUPPORTED_10baseT_Full | + SUPPORTED_100baseT_Half | + SUPPORTED_100baseT_Full | + SUPPORTED_1000baseT_Half | + SUPPORTED_1000baseT_Full | + SUPPORTED_Autoneg | + SUPPORTED_TP); + + if (is_genesis(hw)) + supported &= ~(SUPPORTED_10baseT_Half | + SUPPORTED_10baseT_Full | + SUPPORTED_100baseT_Half | + SUPPORTED_100baseT_Full); + + else if (hw->chip_id == CHIP_ID_YUKON) + supported &= ~SUPPORTED_1000baseT_Half; + } else + supported = (SUPPORTED_1000baseT_Full | + SUPPORTED_1000baseT_Half | + SUPPORTED_FIBRE | + SUPPORTED_Autoneg); + + return supported; +} + +static int skge_get_link_ksettings(struct net_device *dev, + struct ethtool_link_ksettings *cmd) +{ + struct skge_port *skge = netdev_priv(dev); + struct skge_hw *hw = skge->hw; + u32 supported, advertising; + + supported = skge_supported_modes(hw); + + if (hw->copper) { + cmd->base.port = PORT_TP; + cmd->base.phy_address = hw->phy_addr; + } else + cmd->base.port = PORT_FIBRE; + + advertising = skge->advertising; + cmd->base.autoneg = skge->autoneg; + cmd->base.speed = skge->speed; + cmd->base.duplex = skge->duplex; + + ethtool_convert_legacy_u32_to_link_mode(cmd->link_modes.supported, + supported); + ethtool_convert_legacy_u32_to_link_mode(cmd->link_modes.advertising, + advertising); + + return 0; +} + +static int skge_set_link_ksettings(struct net_device *dev, + const struct ethtool_link_ksettings *cmd) +{ + struct skge_port *skge = netdev_priv(dev); + const struct skge_hw *hw = skge->hw; + u32 supported = skge_supported_modes(hw); + int err = 0; + u32 advertising; + + ethtool_convert_link_mode_to_legacy_u32(&advertising, + cmd->link_modes.advertising); + + if (cmd->base.autoneg == AUTONEG_ENABLE) { + advertising = supported; + skge->duplex = -1; + skge->speed = -1; + } else { + u32 setting; + u32 speed = cmd->base.speed; + + switch (speed) { + case SPEED_1000: + if (cmd->base.duplex == DUPLEX_FULL) + setting = SUPPORTED_1000baseT_Full; + else if (cmd->base.duplex == DUPLEX_HALF) + setting = SUPPORTED_1000baseT_Half; + else + return -EINVAL; + break; + case SPEED_100: + if (cmd->base.duplex == DUPLEX_FULL) + setting = SUPPORTED_100baseT_Full; + else if (cmd->base.duplex == DUPLEX_HALF) + setting = SUPPORTED_100baseT_Half; + else + return -EINVAL; + break; + + case SPEED_10: + if (cmd->base.duplex == DUPLEX_FULL) + setting = SUPPORTED_10baseT_Full; + else if (cmd->base.duplex == DUPLEX_HALF) + setting = SUPPORTED_10baseT_Half; + else + return -EINVAL; + break; + default: + return -EINVAL; + } + + if ((setting & supported) == 0) + return -EINVAL; + + skge->speed = speed; + skge->duplex = cmd->base.duplex; + } + + skge->autoneg = cmd->base.autoneg; + skge->advertising = advertising; + + if (netif_running(dev)) { + skge_down(dev); + err = skge_up(dev); + if (err) { + dev_close(dev); + return err; + } + } + + return 0; +} + +static void skge_get_drvinfo(struct net_device *dev, + struct ethtool_drvinfo *info) +{ + struct skge_port *skge = netdev_priv(dev); + + strscpy(info->driver, DRV_NAME, sizeof(info->driver)); + strscpy(info->version, DRV_VERSION, sizeof(info->version)); + strscpy(info->bus_info, pci_name(skge->hw->pdev), + sizeof(info->bus_info)); +} + +static const struct skge_stat { + char name[ETH_GSTRING_LEN]; + u16 xmac_offset; + u16 gma_offset; +} skge_stats[] = { + { "tx_bytes", XM_TXO_OK_HI, GM_TXO_OK_HI }, + { "rx_bytes", XM_RXO_OK_HI, GM_RXO_OK_HI }, + + { "tx_broadcast", XM_TXF_BC_OK, GM_TXF_BC_OK }, + { "rx_broadcast", XM_RXF_BC_OK, GM_RXF_BC_OK }, + { "tx_multicast", XM_TXF_MC_OK, GM_TXF_MC_OK }, + { "rx_multicast", XM_RXF_MC_OK, GM_RXF_MC_OK }, + { "tx_unicast", XM_TXF_UC_OK, GM_TXF_UC_OK }, + { "rx_unicast", XM_RXF_UC_OK, GM_RXF_UC_OK }, + { "tx_mac_pause", XM_TXF_MPAUSE, GM_TXF_MPAUSE }, + { "rx_mac_pause", XM_RXF_MPAUSE, GM_RXF_MPAUSE }, + + { "collisions", XM_TXF_SNG_COL, GM_TXF_SNG_COL }, + { "multi_collisions", XM_TXF_MUL_COL, GM_TXF_MUL_COL }, + { "aborted", XM_TXF_ABO_COL, GM_TXF_ABO_COL }, + { "late_collision", XM_TXF_LAT_COL, GM_TXF_LAT_COL }, + { "fifo_underrun", XM_TXE_FIFO_UR, GM_TXE_FIFO_UR }, + { "fifo_overflow", XM_RXE_FIFO_OV, GM_RXE_FIFO_OV }, + + { "rx_toolong", XM_RXF_LNG_ERR, GM_RXF_LNG_ERR }, + { "rx_jabber", XM_RXF_JAB_PKT, GM_RXF_JAB_PKT }, + { "rx_runt", XM_RXE_RUNT, GM_RXE_FRAG }, + { "rx_too_long", XM_RXF_LNG_ERR, GM_RXF_LNG_ERR }, + { "rx_fcs_error", XM_RXF_FCS_ERR, GM_RXF_FCS_ERR }, +}; + +static int skge_get_sset_count(struct net_device *dev, int sset) +{ + switch (sset) { + case ETH_SS_STATS: + return ARRAY_SIZE(skge_stats); + default: + return -EOPNOTSUPP; + } +} + +static void skge_get_ethtool_stats(struct net_device *dev, + struct ethtool_stats *stats, u64 *data) +{ + struct skge_port *skge = netdev_priv(dev); + + if (is_genesis(skge->hw)) + genesis_get_stats(skge, data); + else + yukon_get_stats(skge, data); +} + +/* Use hardware MIB variables for critical path statistics and + * transmit feedback not reported at interrupt. + * Other errors are accounted for in interrupt handler. + */ +static struct net_device_stats *skge_get_stats(struct net_device *dev) +{ + struct skge_port *skge = netdev_priv(dev); + u64 data[ARRAY_SIZE(skge_stats)]; + + if (is_genesis(skge->hw)) + genesis_get_stats(skge, data); + else + yukon_get_stats(skge, data); + + dev->stats.tx_bytes = data[0]; + dev->stats.rx_bytes = data[1]; + dev->stats.tx_packets = data[2] + data[4] + data[6]; + dev->stats.rx_packets = data[3] + data[5] + data[7]; + dev->stats.multicast = data[3] + data[5]; + dev->stats.collisions = data[10]; + dev->stats.tx_aborted_errors = data[12]; + + return &dev->stats; +} + +static void skge_get_strings(struct net_device *dev, u32 stringset, u8 *data) +{ + int i; + + switch (stringset) { + case ETH_SS_STATS: + for (i = 0; i < ARRAY_SIZE(skge_stats); i++) + memcpy(data + i * ETH_GSTRING_LEN, + skge_stats[i].name, ETH_GSTRING_LEN); + break; + } +} + +static void skge_get_ring_param(struct net_device *dev, + struct ethtool_ringparam *p, + struct kernel_ethtool_ringparam *kernel_p, + struct netlink_ext_ack *extack) +{ + struct skge_port *skge = netdev_priv(dev); + + p->rx_max_pending = MAX_RX_RING_SIZE; + p->tx_max_pending = MAX_TX_RING_SIZE; + + p->rx_pending = skge->rx_ring.count; + p->tx_pending = skge->tx_ring.count; +} + +static int skge_set_ring_param(struct net_device *dev, + struct ethtool_ringparam *p, + struct kernel_ethtool_ringparam *kernel_p, + struct netlink_ext_ack *extack) +{ + struct skge_port *skge = netdev_priv(dev); + int err = 0; + + if (p->rx_pending == 0 || p->rx_pending > MAX_RX_RING_SIZE || + p->tx_pending < TX_LOW_WATER || p->tx_pending > MAX_TX_RING_SIZE) + return -EINVAL; + + skge->rx_ring.count = p->rx_pending; + skge->tx_ring.count = p->tx_pending; + + if (netif_running(dev)) { + skge_down(dev); + err = skge_up(dev); + if (err) + dev_close(dev); + } + + return err; +} + +static u32 skge_get_msglevel(struct net_device *netdev) +{ + struct skge_port *skge = netdev_priv(netdev); + return skge->msg_enable; +} + +static void skge_set_msglevel(struct net_device *netdev, u32 value) +{ + struct skge_port *skge = netdev_priv(netdev); + skge->msg_enable = value; +} + +static int skge_nway_reset(struct net_device *dev) +{ + struct skge_port *skge = netdev_priv(dev); + + if (skge->autoneg != AUTONEG_ENABLE || !netif_running(dev)) + return -EINVAL; + + skge_phy_reset(skge); + return 0; +} + +static void skge_get_pauseparam(struct net_device *dev, + struct ethtool_pauseparam *ecmd) +{ + struct skge_port *skge = netdev_priv(dev); + + ecmd->rx_pause = ((skge->flow_control == FLOW_MODE_SYMMETRIC) || + (skge->flow_control == FLOW_MODE_SYM_OR_REM)); + ecmd->tx_pause = (ecmd->rx_pause || + (skge->flow_control == FLOW_MODE_LOC_SEND)); + + ecmd->autoneg = ecmd->rx_pause || ecmd->tx_pause; +} + +static int skge_set_pauseparam(struct net_device *dev, + struct ethtool_pauseparam *ecmd) +{ + struct skge_port *skge = netdev_priv(dev); + struct ethtool_pauseparam old; + int err = 0; + + skge_get_pauseparam(dev, &old); + + if (ecmd->autoneg != old.autoneg) + skge->flow_control = ecmd->autoneg ? FLOW_MODE_NONE : FLOW_MODE_SYMMETRIC; + else { + if (ecmd->rx_pause && ecmd->tx_pause) + skge->flow_control = FLOW_MODE_SYMMETRIC; + else if (ecmd->rx_pause && !ecmd->tx_pause) + skge->flow_control = FLOW_MODE_SYM_OR_REM; + else if (!ecmd->rx_pause && ecmd->tx_pause) + skge->flow_control = FLOW_MODE_LOC_SEND; + else + skge->flow_control = FLOW_MODE_NONE; + } + + if (netif_running(dev)) { + skge_down(dev); + err = skge_up(dev); + if (err) { + dev_close(dev); + return err; + } + } + + return 0; +} + +/* Chip internal frequency for clock calculations */ +static inline u32 hwkhz(const struct skge_hw *hw) +{ + return is_genesis(hw) ? 53125 : 78125; +} + +/* Chip HZ to microseconds */ +static inline u32 skge_clk2usec(const struct skge_hw *hw, u32 ticks) +{ + return (ticks * 1000) / hwkhz(hw); +} + +/* Microseconds to chip HZ */ +static inline u32 skge_usecs2clk(const struct skge_hw *hw, u32 usec) +{ + return hwkhz(hw) * usec / 1000; +} + +static int skge_get_coalesce(struct net_device *dev, + struct ethtool_coalesce *ecmd, + struct kernel_ethtool_coalesce *kernel_coal, + struct netlink_ext_ack *extack) +{ + struct skge_port *skge = netdev_priv(dev); + struct skge_hw *hw = skge->hw; + int port = skge->port; + + ecmd->rx_coalesce_usecs = 0; + ecmd->tx_coalesce_usecs = 0; + + if (skge_read32(hw, B2_IRQM_CTRL) & TIM_START) { + u32 delay = skge_clk2usec(hw, skge_read32(hw, B2_IRQM_INI)); + u32 msk = skge_read32(hw, B2_IRQM_MSK); + + if (msk & rxirqmask[port]) + ecmd->rx_coalesce_usecs = delay; + if (msk & txirqmask[port]) + ecmd->tx_coalesce_usecs = delay; + } + + return 0; +} + +/* Note: interrupt timer is per board, but can turn on/off per port */ +static int skge_set_coalesce(struct net_device *dev, + struct ethtool_coalesce *ecmd, + struct kernel_ethtool_coalesce *kernel_coal, + struct netlink_ext_ack *extack) +{ + struct skge_port *skge = netdev_priv(dev); + struct skge_hw *hw = skge->hw; + int port = skge->port; + u32 msk = skge_read32(hw, B2_IRQM_MSK); + u32 delay = 25; + + if (ecmd->rx_coalesce_usecs == 0) + msk &= ~rxirqmask[port]; + else if (ecmd->rx_coalesce_usecs < 25 || + ecmd->rx_coalesce_usecs > 33333) + return -EINVAL; + else { + msk |= rxirqmask[port]; + delay = ecmd->rx_coalesce_usecs; + } + + if (ecmd->tx_coalesce_usecs == 0) + msk &= ~txirqmask[port]; + else if (ecmd->tx_coalesce_usecs < 25 || + ecmd->tx_coalesce_usecs > 33333) + return -EINVAL; + else { + msk |= txirqmask[port]; + delay = min(delay, ecmd->rx_coalesce_usecs); + } + + skge_write32(hw, B2_IRQM_MSK, msk); + if (msk == 0) + skge_write32(hw, B2_IRQM_CTRL, TIM_STOP); + else { + skge_write32(hw, B2_IRQM_INI, skge_usecs2clk(hw, delay)); + skge_write32(hw, B2_IRQM_CTRL, TIM_START); + } + return 0; +} + +enum led_mode { LED_MODE_OFF, LED_MODE_ON, LED_MODE_TST }; +static void skge_led(struct skge_port *skge, enum led_mode mode) +{ + struct skge_hw *hw = skge->hw; + int port = skge->port; + + spin_lock_bh(&hw->phy_lock); + if (is_genesis(hw)) { + switch (mode) { + case LED_MODE_OFF: + if (hw->phy_type == SK_PHY_BCOM) + xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, PHY_B_PEC_LED_OFF); + else { + skge_write32(hw, SK_REG(port, TX_LED_VAL), 0); + skge_write8(hw, SK_REG(port, TX_LED_CTRL), LED_T_OFF); + } + skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_OFF); + skge_write32(hw, SK_REG(port, RX_LED_VAL), 0); + skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_T_OFF); + break; + + case LED_MODE_ON: + skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_ON); + skge_write8(hw, SK_REG(port, LNK_LED_REG), LINKLED_LINKSYNC_ON); + + skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_START); + skge_write8(hw, SK_REG(port, TX_LED_CTRL), LED_START); + + break; + + case LED_MODE_TST: + skge_write8(hw, SK_REG(port, RX_LED_TST), LED_T_ON); + skge_write32(hw, SK_REG(port, RX_LED_VAL), 100); + skge_write8(hw, SK_REG(port, RX_LED_CTRL), LED_START); + + if (hw->phy_type == SK_PHY_BCOM) + xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, PHY_B_PEC_LED_ON); + else { + skge_write8(hw, SK_REG(port, TX_LED_TST), LED_T_ON); + skge_write32(hw, SK_REG(port, TX_LED_VAL), 100); + skge_write8(hw, SK_REG(port, TX_LED_CTRL), LED_START); + } + + } + } else { + switch (mode) { + case LED_MODE_OFF: + gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0); + gm_phy_write(hw, port, PHY_MARV_LED_OVER, + PHY_M_LED_MO_DUP(MO_LED_OFF) | + PHY_M_LED_MO_10(MO_LED_OFF) | + PHY_M_LED_MO_100(MO_LED_OFF) | + PHY_M_LED_MO_1000(MO_LED_OFF) | + PHY_M_LED_MO_RX(MO_LED_OFF)); + break; + case LED_MODE_ON: + gm_phy_write(hw, port, PHY_MARV_LED_CTRL, + PHY_M_LED_PULS_DUR(PULS_170MS) | + PHY_M_LED_BLINK_RT(BLINK_84MS) | + PHY_M_LEDC_TX_CTRL | + PHY_M_LEDC_DP_CTRL); + + gm_phy_write(hw, port, PHY_MARV_LED_OVER, + PHY_M_LED_MO_RX(MO_LED_OFF) | + (skge->speed == SPEED_100 ? + PHY_M_LED_MO_100(MO_LED_ON) : 0)); + break; + case LED_MODE_TST: + gm_phy_write(hw, port, PHY_MARV_LED_CTRL, 0); + gm_phy_write(hw, port, PHY_MARV_LED_OVER, + PHY_M_LED_MO_DUP(MO_LED_ON) | + PHY_M_LED_MO_10(MO_LED_ON) | + PHY_M_LED_MO_100(MO_LED_ON) | + PHY_M_LED_MO_1000(MO_LED_ON) | + PHY_M_LED_MO_RX(MO_LED_ON)); + } + } + spin_unlock_bh(&hw->phy_lock); +} + +/* blink LED's for finding board */ +static int skge_set_phys_id(struct net_device *dev, + enum ethtool_phys_id_state state) +{ + struct skge_port *skge = netdev_priv(dev); + + switch (state) { + case ETHTOOL_ID_ACTIVE: + return 2; /* cycle on/off twice per second */ + + case ETHTOOL_ID_ON: + skge_led(skge, LED_MODE_TST); + break; + + case ETHTOOL_ID_OFF: + skge_led(skge, LED_MODE_OFF); + break; + + case ETHTOOL_ID_INACTIVE: + /* back to regular LED state */ + skge_led(skge, netif_running(dev) ? LED_MODE_ON : LED_MODE_OFF); + } + + return 0; +} + +static int skge_get_eeprom_len(struct net_device *dev) +{ + struct skge_port *skge = netdev_priv(dev); + u32 reg2; + + pci_read_config_dword(skge->hw->pdev, PCI_DEV_REG2, ®2); + return 1 << (((reg2 & PCI_VPD_ROM_SZ) >> 14) + 8); +} + +static u32 skge_vpd_read(struct pci_dev *pdev, int cap, u16 offset) +{ + u32 val; + + pci_write_config_word(pdev, cap + PCI_VPD_ADDR, offset); + + do { + pci_read_config_word(pdev, cap + PCI_VPD_ADDR, &offset); + } while (!(offset & PCI_VPD_ADDR_F)); + + pci_read_config_dword(pdev, cap + PCI_VPD_DATA, &val); + return val; +} + +static void skge_vpd_write(struct pci_dev *pdev, int cap, u16 offset, u32 val) +{ + pci_write_config_dword(pdev, cap + PCI_VPD_DATA, val); + pci_write_config_word(pdev, cap + PCI_VPD_ADDR, + offset | PCI_VPD_ADDR_F); + + do { + pci_read_config_word(pdev, cap + PCI_VPD_ADDR, &offset); + } while (offset & PCI_VPD_ADDR_F); +} + +static int skge_get_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom, + u8 *data) +{ + struct skge_port *skge = netdev_priv(dev); + struct pci_dev *pdev = skge->hw->pdev; + int cap = pci_find_capability(pdev, PCI_CAP_ID_VPD); + int length = eeprom->len; + u16 offset = eeprom->offset; + + if (!cap) + return -EINVAL; + + eeprom->magic = SKGE_EEPROM_MAGIC; + + while (length > 0) { + u32 val = skge_vpd_read(pdev, cap, offset); + int n = min_t(int, length, sizeof(val)); + + memcpy(data, &val, n); + length -= n; + data += n; + offset += n; + } + return 0; +} + +static int skge_set_eeprom(struct net_device *dev, struct ethtool_eeprom *eeprom, + u8 *data) +{ + struct skge_port *skge = netdev_priv(dev); + struct pci_dev *pdev = skge->hw->pdev; + int cap = pci_find_capability(pdev, PCI_CAP_ID_VPD); + int length = eeprom->len; + u16 offset = eeprom->offset; + + if (!cap) + return -EINVAL; + + if (eeprom->magic != SKGE_EEPROM_MAGIC) + return -EINVAL; + + while (length > 0) { + u32 val; + int n = min_t(int, length, sizeof(val)); + + if (n < sizeof(val)) + val = skge_vpd_read(pdev, cap, offset); + memcpy(&val, data, n); + + skge_vpd_write(pdev, cap, offset, val); + + length -= n; + data += n; + offset += n; + } + return 0; +} + +static const struct ethtool_ops skge_ethtool_ops = { + .supported_coalesce_params = ETHTOOL_COALESCE_USECS, + .get_drvinfo = skge_get_drvinfo, + .get_regs_len = skge_get_regs_len, + .get_regs = skge_get_regs, + .get_wol = skge_get_wol, + .set_wol = skge_set_wol, + .get_msglevel = skge_get_msglevel, + .set_msglevel = skge_set_msglevel, + .nway_reset = skge_nway_reset, + .get_link = ethtool_op_get_link, + .get_eeprom_len = skge_get_eeprom_len, + .get_eeprom = skge_get_eeprom, + .set_eeprom = skge_set_eeprom, + .get_ringparam = skge_get_ring_param, + .set_ringparam = skge_set_ring_param, + .get_pauseparam = skge_get_pauseparam, + .set_pauseparam = skge_set_pauseparam, + .get_coalesce = skge_get_coalesce, + .set_coalesce = skge_set_coalesce, + .get_strings = skge_get_strings, + .set_phys_id = skge_set_phys_id, + .get_sset_count = skge_get_sset_count, + .get_ethtool_stats = skge_get_ethtool_stats, + .get_link_ksettings = skge_get_link_ksettings, + .set_link_ksettings = skge_set_link_ksettings, +}; + +/* + * Allocate ring elements and chain them together + * One-to-one association of board descriptors with ring elements + */ +static int skge_ring_alloc(struct skge_ring *ring, void *vaddr, u32 base) +{ + struct skge_tx_desc *d; + struct skge_element *e; + int i; + + ring->start = kcalloc(ring->count, sizeof(*e), GFP_KERNEL); + if (!ring->start) + return -ENOMEM; + + for (i = 0, e = ring->start, d = vaddr; i < ring->count; i++, e++, d++) { + e->desc = d; + if (i == ring->count - 1) { + e->next = ring->start; + d->next_offset = base; + } else { + e->next = e + 1; + d->next_offset = base + (i+1) * sizeof(*d); + } + } + ring->to_use = ring->to_clean = ring->start; + + return 0; +} + +/* Allocate and setup a new buffer for receiving */ +static int skge_rx_setup(struct skge_port *skge, struct skge_element *e, + struct sk_buff *skb, unsigned int bufsize) +{ + struct skge_rx_desc *rd = e->desc; + dma_addr_t map; + + map = dma_map_single(&skge->hw->pdev->dev, skb->data, bufsize, + DMA_FROM_DEVICE); + + if (dma_mapping_error(&skge->hw->pdev->dev, map)) + return -1; + + rd->dma_lo = lower_32_bits(map); + rd->dma_hi = upper_32_bits(map); + e->skb = skb; + rd->csum1_start = ETH_HLEN; + rd->csum2_start = ETH_HLEN; + rd->csum1 = 0; + rd->csum2 = 0; + + wmb(); + + rd->control = BMU_OWN | BMU_STF | BMU_IRQ_EOF | BMU_TCP_CHECK | bufsize; + dma_unmap_addr_set(e, mapaddr, map); + dma_unmap_len_set(e, maplen, bufsize); + return 0; +} + +/* Resume receiving using existing skb, + * Note: DMA address is not changed by chip. + * MTU not changed while receiver active. + */ +static inline void skge_rx_reuse(struct skge_element *e, unsigned int size) +{ + struct skge_rx_desc *rd = e->desc; + + rd->csum2 = 0; + rd->csum2_start = ETH_HLEN; + + wmb(); + + rd->control = BMU_OWN | BMU_STF | BMU_IRQ_EOF | BMU_TCP_CHECK | size; +} + + +/* Free all buffers in receive ring, assumes receiver stopped */ +static void skge_rx_clean(struct skge_port *skge) +{ + struct skge_hw *hw = skge->hw; + struct skge_ring *ring = &skge->rx_ring; + struct skge_element *e; + + e = ring->start; + do { + struct skge_rx_desc *rd = e->desc; + rd->control = 0; + if (e->skb) { + dma_unmap_single(&hw->pdev->dev, + dma_unmap_addr(e, mapaddr), + dma_unmap_len(e, maplen), + DMA_FROM_DEVICE); + dev_kfree_skb(e->skb); + e->skb = NULL; + } + } while ((e = e->next) != ring->start); +} + + +/* Allocate buffers for receive ring + * For receive: to_clean is next received frame. + */ +static int skge_rx_fill(struct net_device *dev) +{ + struct skge_port *skge = netdev_priv(dev); + struct skge_ring *ring = &skge->rx_ring; + struct skge_element *e; + + e = ring->start; + do { + struct sk_buff *skb; + + skb = __netdev_alloc_skb(dev, skge->rx_buf_size + NET_IP_ALIGN, + GFP_KERNEL); + if (!skb) + return -ENOMEM; + + skb_reserve(skb, NET_IP_ALIGN); + if (skge_rx_setup(skge, e, skb, skge->rx_buf_size) < 0) { + dev_kfree_skb(skb); + return -EIO; + } + } while ((e = e->next) != ring->start); + + ring->to_clean = ring->start; + return 0; +} + +static const char *skge_pause(enum pause_status status) +{ + switch (status) { + case FLOW_STAT_NONE: + return "none"; + case FLOW_STAT_REM_SEND: + return "rx only"; + case FLOW_STAT_LOC_SEND: + return "tx_only"; + case FLOW_STAT_SYMMETRIC: /* Both station may send PAUSE */ + return "both"; + default: + return "indeterminated"; + } +} + + +static void skge_link_up(struct skge_port *skge) +{ + skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), + LED_BLK_OFF|LED_SYNC_OFF|LED_REG_ON); + + netif_carrier_on(skge->netdev); + netif_wake_queue(skge->netdev); + + netif_info(skge, link, skge->netdev, + "Link is up at %d Mbps, %s duplex, flow control %s\n", + skge->speed, + skge->duplex == DUPLEX_FULL ? "full" : "half", + skge_pause(skge->flow_status)); +} + +static void skge_link_down(struct skge_port *skge) +{ + skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_REG_OFF); + netif_carrier_off(skge->netdev); + netif_stop_queue(skge->netdev); + + netif_info(skge, link, skge->netdev, "Link is down\n"); +} + +static void xm_link_down(struct skge_hw *hw, int port) +{ + struct net_device *dev = hw->dev[port]; + struct skge_port *skge = netdev_priv(dev); + + xm_write16(hw, port, XM_IMSK, XM_IMSK_DISABLE); + + if (netif_carrier_ok(dev)) + skge_link_down(skge); +} + +static int __xm_phy_read(struct skge_hw *hw, int port, u16 reg, u16 *val) +{ + int i; + + xm_write16(hw, port, XM_PHY_ADDR, reg | hw->phy_addr); + *val = xm_read16(hw, port, XM_PHY_DATA); + + if (hw->phy_type == SK_PHY_XMAC) + goto ready; + + for (i = 0; i < PHY_RETRIES; i++) { + if (xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_RDY) + goto ready; + udelay(1); + } + + return -ETIMEDOUT; + ready: + *val = xm_read16(hw, port, XM_PHY_DATA); + + return 0; +} + +static u16 xm_phy_read(struct skge_hw *hw, int port, u16 reg) +{ + u16 v = 0; + if (__xm_phy_read(hw, port, reg, &v)) + pr_warn("%s: phy read timed out\n", hw->dev[port]->name); + return v; +} + +static int xm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val) +{ + int i; + + xm_write16(hw, port, XM_PHY_ADDR, reg | hw->phy_addr); + for (i = 0; i < PHY_RETRIES; i++) { + if (!(xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_BUSY)) + goto ready; + udelay(1); + } + return -EIO; + + ready: + xm_write16(hw, port, XM_PHY_DATA, val); + for (i = 0; i < PHY_RETRIES; i++) { + if (!(xm_read16(hw, port, XM_MMU_CMD) & XM_MMU_PHY_BUSY)) + return 0; + udelay(1); + } + return -ETIMEDOUT; +} + +static void genesis_init(struct skge_hw *hw) +{ + /* set blink source counter */ + skge_write32(hw, B2_BSC_INI, (SK_BLK_DUR * SK_FACT_53) / 100); + skge_write8(hw, B2_BSC_CTRL, BSC_START); + + /* configure mac arbiter */ + skge_write16(hw, B3_MA_TO_CTRL, MA_RST_CLR); + + /* configure mac arbiter timeout values */ + skge_write8(hw, B3_MA_TOINI_RX1, SK_MAC_TO_53); + skge_write8(hw, B3_MA_TOINI_RX2, SK_MAC_TO_53); + skge_write8(hw, B3_MA_TOINI_TX1, SK_MAC_TO_53); + skge_write8(hw, B3_MA_TOINI_TX2, SK_MAC_TO_53); + + skge_write8(hw, B3_MA_RCINI_RX1, 0); + skge_write8(hw, B3_MA_RCINI_RX2, 0); + skge_write8(hw, B3_MA_RCINI_TX1, 0); + skge_write8(hw, B3_MA_RCINI_TX2, 0); + + /* configure packet arbiter timeout */ + skge_write16(hw, B3_PA_CTRL, PA_RST_CLR); + skge_write16(hw, B3_PA_TOINI_RX1, SK_PKT_TO_MAX); + skge_write16(hw, B3_PA_TOINI_TX1, SK_PKT_TO_MAX); + skge_write16(hw, B3_PA_TOINI_RX2, SK_PKT_TO_MAX); + skge_write16(hw, B3_PA_TOINI_TX2, SK_PKT_TO_MAX); +} + +static void genesis_reset(struct skge_hw *hw, int port) +{ + static const u8 zero[8] = { 0 }; + u32 reg; + + skge_write8(hw, SK_REG(port, GMAC_IRQ_MSK), 0); + + /* reset the statistics module */ + xm_write32(hw, port, XM_GP_PORT, XM_GP_RES_STAT); + xm_write16(hw, port, XM_IMSK, XM_IMSK_DISABLE); + xm_write32(hw, port, XM_MODE, 0); /* clear Mode Reg */ + xm_write16(hw, port, XM_TX_CMD, 0); /* reset TX CMD Reg */ + xm_write16(hw, port, XM_RX_CMD, 0); /* reset RX CMD Reg */ + + /* disable Broadcom PHY IRQ */ + if (hw->phy_type == SK_PHY_BCOM) + xm_write16(hw, port, PHY_BCOM_INT_MASK, 0xffff); + + xm_outhash(hw, port, XM_HSM, zero); + + /* Flush TX and RX fifo */ + reg = xm_read32(hw, port, XM_MODE); + xm_write32(hw, port, XM_MODE, reg | XM_MD_FTF); + xm_write32(hw, port, XM_MODE, reg | XM_MD_FRF); +} + +/* Convert mode to MII values */ +static const u16 phy_pause_map[] = { + [FLOW_MODE_NONE] = 0, + [FLOW_MODE_LOC_SEND] = PHY_AN_PAUSE_ASYM, + [FLOW_MODE_SYMMETRIC] = PHY_AN_PAUSE_CAP, + [FLOW_MODE_SYM_OR_REM] = PHY_AN_PAUSE_CAP | PHY_AN_PAUSE_ASYM, +}; + +/* special defines for FIBER (88E1011S only) */ +static const u16 fiber_pause_map[] = { + [FLOW_MODE_NONE] = PHY_X_P_NO_PAUSE, + [FLOW_MODE_LOC_SEND] = PHY_X_P_ASYM_MD, + [FLOW_MODE_SYMMETRIC] = PHY_X_P_SYM_MD, + [FLOW_MODE_SYM_OR_REM] = PHY_X_P_BOTH_MD, +}; + + +/* Check status of Broadcom phy link */ +static void bcom_check_link(struct skge_hw *hw, int port) +{ + struct net_device *dev = hw->dev[port]; + struct skge_port *skge = netdev_priv(dev); + u16 status; + + /* read twice because of latch */ + xm_phy_read(hw, port, PHY_BCOM_STAT); + status = xm_phy_read(hw, port, PHY_BCOM_STAT); + + if ((status & PHY_ST_LSYNC) == 0) { + xm_link_down(hw, port); + return; + } + + if (skge->autoneg == AUTONEG_ENABLE) { + u16 lpa, aux; + + if (!(status & PHY_ST_AN_OVER)) + return; + + lpa = xm_phy_read(hw, port, PHY_XMAC_AUNE_LP); + if (lpa & PHY_B_AN_RF) { + netdev_notice(dev, "remote fault\n"); + return; + } + + aux = xm_phy_read(hw, port, PHY_BCOM_AUX_STAT); + + /* Check Duplex mismatch */ + switch (aux & PHY_B_AS_AN_RES_MSK) { + case PHY_B_RES_1000FD: + skge->duplex = DUPLEX_FULL; + break; + case PHY_B_RES_1000HD: + skge->duplex = DUPLEX_HALF; + break; + default: + netdev_notice(dev, "duplex mismatch\n"); + return; + } + + /* We are using IEEE 802.3z/D5.0 Table 37-4 */ + switch (aux & PHY_B_AS_PAUSE_MSK) { + case PHY_B_AS_PAUSE_MSK: + skge->flow_status = FLOW_STAT_SYMMETRIC; + break; + case PHY_B_AS_PRR: + skge->flow_status = FLOW_STAT_REM_SEND; + break; + case PHY_B_AS_PRT: + skge->flow_status = FLOW_STAT_LOC_SEND; + break; + default: + skge->flow_status = FLOW_STAT_NONE; + } + skge->speed = SPEED_1000; + } + + if (!netif_carrier_ok(dev)) + genesis_link_up(skge); +} + +/* Broadcom 5400 only supports giagabit! SysKonnect did not put an additional + * Phy on for 100 or 10Mbit operation + */ +static void bcom_phy_init(struct skge_port *skge) +{ + struct skge_hw *hw = skge->hw; + int port = skge->port; + int i; + u16 id1, r, ext, ctl; + + /* magic workaround patterns for Broadcom */ + static const struct { + u16 reg; + u16 val; + } A1hack[] = { + { 0x18, 0x0c20 }, { 0x17, 0x0012 }, { 0x15, 0x1104 }, + { 0x17, 0x0013 }, { 0x15, 0x0404 }, { 0x17, 0x8006 }, + { 0x15, 0x0132 }, { 0x17, 0x8006 }, { 0x15, 0x0232 }, + { 0x17, 0x800D }, { 0x15, 0x000F }, { 0x18, 0x0420 }, + }, C0hack[] = { + { 0x18, 0x0c20 }, { 0x17, 0x0012 }, { 0x15, 0x1204 }, + { 0x17, 0x0013 }, { 0x15, 0x0A04 }, { 0x18, 0x0420 }, + }; + + /* read Id from external PHY (all have the same address) */ + id1 = xm_phy_read(hw, port, PHY_XMAC_ID1); + + /* Optimize MDIO transfer by suppressing preamble. */ + r = xm_read16(hw, port, XM_MMU_CMD); + r |= XM_MMU_NO_PRE; + xm_write16(hw, port, XM_MMU_CMD, r); + + switch (id1) { + case PHY_BCOM_ID1_C0: + /* + * Workaround BCOM Errata for the C0 type. + * Write magic patterns to reserved registers. + */ + for (i = 0; i < ARRAY_SIZE(C0hack); i++) + xm_phy_write(hw, port, + C0hack[i].reg, C0hack[i].val); + + break; + case PHY_BCOM_ID1_A1: + /* + * Workaround BCOM Errata for the A1 type. + * Write magic patterns to reserved registers. + */ + for (i = 0; i < ARRAY_SIZE(A1hack); i++) + xm_phy_write(hw, port, + A1hack[i].reg, A1hack[i].val); + break; + } + + /* + * Workaround BCOM Errata (#10523) for all BCom PHYs. + * Disable Power Management after reset. + */ + r = xm_phy_read(hw, port, PHY_BCOM_AUX_CTRL); + r |= PHY_B_AC_DIS_PM; + xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL, r); + + /* Dummy read */ + xm_read16(hw, port, XM_ISRC); + + ext = PHY_B_PEC_EN_LTR; /* enable tx led */ + ctl = PHY_CT_SP1000; /* always 1000mbit */ + + if (skge->autoneg == AUTONEG_ENABLE) { + /* + * Workaround BCOM Errata #1 for the C5 type. + * 1000Base-T Link Acquisition Failure in Slave Mode + * Set Repeater/DTE bit 10 of the 1000Base-T Control Register + */ + u16 adv = PHY_B_1000C_RD; + if (skge->advertising & ADVERTISED_1000baseT_Half) + adv |= PHY_B_1000C_AHD; + if (skge->advertising & ADVERTISED_1000baseT_Full) + adv |= PHY_B_1000C_AFD; + xm_phy_write(hw, port, PHY_BCOM_1000T_CTRL, adv); + + ctl |= PHY_CT_ANE | PHY_CT_RE_CFG; + } else { + if (skge->duplex == DUPLEX_FULL) + ctl |= PHY_CT_DUP_MD; + /* Force to slave */ + xm_phy_write(hw, port, PHY_BCOM_1000T_CTRL, PHY_B_1000C_MSE); + } + + /* Set autonegotiation pause parameters */ + xm_phy_write(hw, port, PHY_BCOM_AUNE_ADV, + phy_pause_map[skge->flow_control] | PHY_AN_CSMA); + + /* Handle Jumbo frames */ + if (hw->dev[port]->mtu > ETH_DATA_LEN) { + xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL, + PHY_B_AC_TX_TST | PHY_B_AC_LONG_PACK); + + ext |= PHY_B_PEC_HIGH_LA; + + } + + xm_phy_write(hw, port, PHY_BCOM_P_EXT_CTRL, ext); + xm_phy_write(hw, port, PHY_BCOM_CTRL, ctl); + + /* Use link status change interrupt */ + xm_phy_write(hw, port, PHY_BCOM_INT_MASK, PHY_B_DEF_MSK); +} + +static void xm_phy_init(struct skge_port *skge) +{ + struct skge_hw *hw = skge->hw; + int port = skge->port; + u16 ctrl = 0; + + if (skge->autoneg == AUTONEG_ENABLE) { + if (skge->advertising & ADVERTISED_1000baseT_Half) + ctrl |= PHY_X_AN_HD; + if (skge->advertising & ADVERTISED_1000baseT_Full) + ctrl |= PHY_X_AN_FD; + + ctrl |= fiber_pause_map[skge->flow_control]; + + xm_phy_write(hw, port, PHY_XMAC_AUNE_ADV, ctrl); + + /* Restart Auto-negotiation */ + ctrl = PHY_CT_ANE | PHY_CT_RE_CFG; + } else { + /* Set DuplexMode in Config register */ + if (skge->duplex == DUPLEX_FULL) + ctrl |= PHY_CT_DUP_MD; + /* + * Do NOT enable Auto-negotiation here. This would hold + * the link down because no IDLEs are transmitted + */ + } + + xm_phy_write(hw, port, PHY_XMAC_CTRL, ctrl); + + /* Poll PHY for status changes */ + mod_timer(&skge->link_timer, jiffies + LINK_HZ); +} + +static int xm_check_link(struct net_device *dev) +{ + struct skge_port *skge = netdev_priv(dev); + struct skge_hw *hw = skge->hw; + int port = skge->port; + u16 status; + + /* read twice because of latch */ + xm_phy_read(hw, port, PHY_XMAC_STAT); + status = xm_phy_read(hw, port, PHY_XMAC_STAT); + + if ((status & PHY_ST_LSYNC) == 0) { + xm_link_down(hw, port); + return 0; + } + + if (skge->autoneg == AUTONEG_ENABLE) { + u16 lpa, res; + + if (!(status & PHY_ST_AN_OVER)) + return 0; + + lpa = xm_phy_read(hw, port, PHY_XMAC_AUNE_LP); + if (lpa & PHY_B_AN_RF) { + netdev_notice(dev, "remote fault\n"); + return 0; + } + + res = xm_phy_read(hw, port, PHY_XMAC_RES_ABI); + + /* Check Duplex mismatch */ + switch (res & (PHY_X_RS_HD | PHY_X_RS_FD)) { + case PHY_X_RS_FD: + skge->duplex = DUPLEX_FULL; + break; + case PHY_X_RS_HD: + skge->duplex = DUPLEX_HALF; + break; + default: + netdev_notice(dev, "duplex mismatch\n"); + return 0; + } + + /* We are using IEEE 802.3z/D5.0 Table 37-4 */ + if ((skge->flow_control == FLOW_MODE_SYMMETRIC || + skge->flow_control == FLOW_MODE_SYM_OR_REM) && + (lpa & PHY_X_P_SYM_MD)) + skge->flow_status = FLOW_STAT_SYMMETRIC; + else if (skge->flow_control == FLOW_MODE_SYM_OR_REM && + (lpa & PHY_X_RS_PAUSE) == PHY_X_P_ASYM_MD) + /* Enable PAUSE receive, disable PAUSE transmit */ + skge->flow_status = FLOW_STAT_REM_SEND; + else if (skge->flow_control == FLOW_MODE_LOC_SEND && + (lpa & PHY_X_RS_PAUSE) == PHY_X_P_BOTH_MD) + /* Disable PAUSE receive, enable PAUSE transmit */ + skge->flow_status = FLOW_STAT_LOC_SEND; + else + skge->flow_status = FLOW_STAT_NONE; + + skge->speed = SPEED_1000; + } + + if (!netif_carrier_ok(dev)) + genesis_link_up(skge); + return 1; +} + +/* Poll to check for link coming up. + * + * Since internal PHY is wired to a level triggered pin, can't + * get an interrupt when carrier is detected, need to poll for + * link coming up. + */ +static void xm_link_timer(struct timer_list *t) +{ + struct skge_port *skge = from_timer(skge, t, link_timer); + struct net_device *dev = skge->netdev; + struct skge_hw *hw = skge->hw; + int port = skge->port; + int i; + unsigned long flags; + + if (!netif_running(dev)) + return; + + spin_lock_irqsave(&hw->phy_lock, flags); + + /* + * Verify that the link by checking GPIO register three times. + * This pin has the signal from the link_sync pin connected to it. + */ + for (i = 0; i < 3; i++) { + if (xm_read16(hw, port, XM_GP_PORT) & XM_GP_INP_ASS) + goto link_down; + } + + /* Re-enable interrupt to detect link down */ + if (xm_check_link(dev)) { + u16 msk = xm_read16(hw, port, XM_IMSK); + msk &= ~XM_IS_INP_ASS; + xm_write16(hw, port, XM_IMSK, msk); + xm_read16(hw, port, XM_ISRC); + } else { +link_down: + mod_timer(&skge->link_timer, + round_jiffies(jiffies + LINK_HZ)); + } + spin_unlock_irqrestore(&hw->phy_lock, flags); +} + +static void genesis_mac_init(struct skge_hw *hw, int port) +{ + struct net_device *dev = hw->dev[port]; + struct skge_port *skge = netdev_priv(dev); + int jumbo = hw->dev[port]->mtu > ETH_DATA_LEN; + int i; + u32 r; + static const u8 zero[6] = { 0 }; + + for (i = 0; i < 10; i++) { + skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), + MFF_SET_MAC_RST); + if (skge_read16(hw, SK_REG(port, TX_MFF_CTRL1)) & MFF_SET_MAC_RST) + goto reset_ok; + udelay(1); + } + + netdev_warn(dev, "genesis reset failed\n"); + + reset_ok: + /* Unreset the XMAC. */ + skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_CLR_MAC_RST); + + /* + * Perform additional initialization for external PHYs, + * namely for the 1000baseTX cards that use the XMAC's + * GMII mode. + */ + if (hw->phy_type != SK_PHY_XMAC) { + /* Take external Phy out of reset */ + r = skge_read32(hw, B2_GP_IO); + if (port == 0) + r |= GP_DIR_0|GP_IO_0; + else + r |= GP_DIR_2|GP_IO_2; + + skge_write32(hw, B2_GP_IO, r); + + /* Enable GMII interface */ + xm_write16(hw, port, XM_HW_CFG, XM_HW_GMII_MD); + } + + + switch (hw->phy_type) { + case SK_PHY_XMAC: + xm_phy_init(skge); + break; + case SK_PHY_BCOM: + bcom_phy_init(skge); + bcom_check_link(hw, port); + } + + /* Set Station Address */ + xm_outaddr(hw, port, XM_SA, dev->dev_addr); + + /* We don't use match addresses so clear */ + for (i = 1; i < 16; i++) + xm_outaddr(hw, port, XM_EXM(i), zero); + + /* Clear MIB counters */ + xm_write16(hw, port, XM_STAT_CMD, + XM_SC_CLR_RXC | XM_SC_CLR_TXC); + /* Clear two times according to Errata #3 */ + xm_write16(hw, port, XM_STAT_CMD, + XM_SC_CLR_RXC | XM_SC_CLR_TXC); + + /* configure Rx High Water Mark (XM_RX_HI_WM) */ + xm_write16(hw, port, XM_RX_HI_WM, 1450); + + /* We don't need the FCS appended to the packet. */ + r = XM_RX_LENERR_OK | XM_RX_STRIP_FCS; + if (jumbo) + r |= XM_RX_BIG_PK_OK; + + if (skge->duplex == DUPLEX_HALF) { + /* + * If in manual half duplex mode the other side might be in + * full duplex mode, so ignore if a carrier extension is not seen + * on frames received + */ + r |= XM_RX_DIS_CEXT; + } + xm_write16(hw, port, XM_RX_CMD, r); + + /* We want short frames padded to 60 bytes. */ + xm_write16(hw, port, XM_TX_CMD, XM_TX_AUTO_PAD); + + /* Increase threshold for jumbo frames on dual port */ + if (hw->ports > 1 && jumbo) + xm_write16(hw, port, XM_TX_THR, 1020); + else + xm_write16(hw, port, XM_TX_THR, 512); + + /* + * Enable the reception of all error frames. This is + * a necessary evil due to the design of the XMAC. The + * XMAC's receive FIFO is only 8K in size, however jumbo + * frames can be up to 9000 bytes in length. When bad + * frame filtering is enabled, the XMAC's RX FIFO operates + * in 'store and forward' mode. For this to work, the + * entire frame has to fit into the FIFO, but that means + * that jumbo frames larger than 8192 bytes will be + * truncated. Disabling all bad frame filtering causes + * the RX FIFO to operate in streaming mode, in which + * case the XMAC will start transferring frames out of the + * RX FIFO as soon as the FIFO threshold is reached. + */ + xm_write32(hw, port, XM_MODE, XM_DEF_MODE); + + + /* + * Initialize the Receive Counter Event Mask (XM_RX_EV_MSK) + * - Enable all bits excepting 'Octets Rx OK Low CntOv' + * and 'Octets Rx OK Hi Cnt Ov'. + */ + xm_write32(hw, port, XM_RX_EV_MSK, XMR_DEF_MSK); + + /* + * Initialize the Transmit Counter Event Mask (XM_TX_EV_MSK) + * - Enable all bits excepting 'Octets Tx OK Low CntOv' + * and 'Octets Tx OK Hi Cnt Ov'. + */ + xm_write32(hw, port, XM_TX_EV_MSK, XMT_DEF_MSK); + + /* Configure MAC arbiter */ + skge_write16(hw, B3_MA_TO_CTRL, MA_RST_CLR); + + /* configure timeout values */ + skge_write8(hw, B3_MA_TOINI_RX1, 72); + skge_write8(hw, B3_MA_TOINI_RX2, 72); + skge_write8(hw, B3_MA_TOINI_TX1, 72); + skge_write8(hw, B3_MA_TOINI_TX2, 72); + + skge_write8(hw, B3_MA_RCINI_RX1, 0); + skge_write8(hw, B3_MA_RCINI_RX2, 0); + skge_write8(hw, B3_MA_RCINI_TX1, 0); + skge_write8(hw, B3_MA_RCINI_TX2, 0); + + /* Configure Rx MAC FIFO */ + skge_write8(hw, SK_REG(port, RX_MFF_CTRL2), MFF_RST_CLR); + skge_write16(hw, SK_REG(port, RX_MFF_CTRL1), MFF_ENA_TIM_PAT); + skge_write8(hw, SK_REG(port, RX_MFF_CTRL2), MFF_ENA_OP_MD); + + /* Configure Tx MAC FIFO */ + skge_write8(hw, SK_REG(port, TX_MFF_CTRL2), MFF_RST_CLR); + skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_TX_CTRL_DEF); + skge_write8(hw, SK_REG(port, TX_MFF_CTRL2), MFF_ENA_OP_MD); + + if (jumbo) { + /* Enable frame flushing if jumbo frames used */ + skge_write16(hw, SK_REG(port, RX_MFF_CTRL1), MFF_ENA_FLUSH); + } else { + /* enable timeout timers if normal frames */ + skge_write16(hw, B3_PA_CTRL, + (port == 0) ? PA_ENA_TO_TX1 : PA_ENA_TO_TX2); + } +} + +static void genesis_stop(struct skge_port *skge) +{ + struct skge_hw *hw = skge->hw; + int port = skge->port; + unsigned retries = 1000; + u16 cmd; + + /* Disable Tx and Rx */ + cmd = xm_read16(hw, port, XM_MMU_CMD); + cmd &= ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX); + xm_write16(hw, port, XM_MMU_CMD, cmd); + + genesis_reset(hw, port); + + /* Clear Tx packet arbiter timeout IRQ */ + skge_write16(hw, B3_PA_CTRL, + port == 0 ? PA_CLR_TO_TX1 : PA_CLR_TO_TX2); + + /* Reset the MAC */ + skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_CLR_MAC_RST); + do { + skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), MFF_SET_MAC_RST); + if (!(skge_read16(hw, SK_REG(port, TX_MFF_CTRL1)) & MFF_SET_MAC_RST)) + break; + } while (--retries > 0); + + /* For external PHYs there must be special handling */ + if (hw->phy_type != SK_PHY_XMAC) { + u32 reg = skge_read32(hw, B2_GP_IO); + if (port == 0) { + reg |= GP_DIR_0; + reg &= ~GP_IO_0; + } else { + reg |= GP_DIR_2; + reg &= ~GP_IO_2; + } + skge_write32(hw, B2_GP_IO, reg); + skge_read32(hw, B2_GP_IO); + } + + xm_write16(hw, port, XM_MMU_CMD, + xm_read16(hw, port, XM_MMU_CMD) + & ~(XM_MMU_ENA_RX | XM_MMU_ENA_TX)); + + xm_read16(hw, port, XM_MMU_CMD); +} + + +static void genesis_get_stats(struct skge_port *skge, u64 *data) +{ + struct skge_hw *hw = skge->hw; + int port = skge->port; + int i; + unsigned long timeout = jiffies + HZ; + + xm_write16(hw, port, + XM_STAT_CMD, XM_SC_SNP_TXC | XM_SC_SNP_RXC); + + /* wait for update to complete */ + while (xm_read16(hw, port, XM_STAT_CMD) + & (XM_SC_SNP_TXC | XM_SC_SNP_RXC)) { + if (time_after(jiffies, timeout)) + break; + udelay(10); + } + + /* special case for 64 bit octet counter */ + data[0] = (u64) xm_read32(hw, port, XM_TXO_OK_HI) << 32 + | xm_read32(hw, port, XM_TXO_OK_LO); + data[1] = (u64) xm_read32(hw, port, XM_RXO_OK_HI) << 32 + | xm_read32(hw, port, XM_RXO_OK_LO); + + for (i = 2; i < ARRAY_SIZE(skge_stats); i++) + data[i] = xm_read32(hw, port, skge_stats[i].xmac_offset); +} + +static void genesis_mac_intr(struct skge_hw *hw, int port) +{ + struct net_device *dev = hw->dev[port]; + struct skge_port *skge = netdev_priv(dev); + u16 status = xm_read16(hw, port, XM_ISRC); + + netif_printk(skge, intr, KERN_DEBUG, skge->netdev, + "mac interrupt status 0x%x\n", status); + + if (hw->phy_type == SK_PHY_XMAC && (status & XM_IS_INP_ASS)) { + xm_link_down(hw, port); + mod_timer(&skge->link_timer, jiffies + 1); + } + + if (status & XM_IS_TXF_UR) { + xm_write32(hw, port, XM_MODE, XM_MD_FTF); + ++dev->stats.tx_fifo_errors; + } +} + +static void genesis_link_up(struct skge_port *skge) +{ + struct skge_hw *hw = skge->hw; + int port = skge->port; + u16 cmd, msk; + u32 mode; + + cmd = xm_read16(hw, port, XM_MMU_CMD); + + /* + * enabling pause frame reception is required for 1000BT + * because the XMAC is not reset if the link is going down + */ + if (skge->flow_status == FLOW_STAT_NONE || + skge->flow_status == FLOW_STAT_LOC_SEND) + /* Disable Pause Frame Reception */ + cmd |= XM_MMU_IGN_PF; + else + /* Enable Pause Frame Reception */ + cmd &= ~XM_MMU_IGN_PF; + + xm_write16(hw, port, XM_MMU_CMD, cmd); + + mode = xm_read32(hw, port, XM_MODE); + if (skge->flow_status == FLOW_STAT_SYMMETRIC || + skge->flow_status == FLOW_STAT_LOC_SEND) { + /* + * Configure Pause Frame Generation + * Use internal and external Pause Frame Generation. + * Sending pause frames is edge triggered. + * Send a Pause frame with the maximum pause time if + * internal oder external FIFO full condition occurs. + * Send a zero pause time frame to re-start transmission. + */ + /* XM_PAUSE_DA = '010000C28001' (default) */ + /* XM_MAC_PTIME = 0xffff (maximum) */ + /* remember this value is defined in big endian (!) */ + xm_write16(hw, port, XM_MAC_PTIME, 0xffff); + + mode |= XM_PAUSE_MODE; + skge_write16(hw, SK_REG(port, RX_MFF_CTRL1), MFF_ENA_PAUSE); + } else { + /* + * disable pause frame generation is required for 1000BT + * because the XMAC is not reset if the link is going down + */ + /* Disable Pause Mode in Mode Register */ + mode &= ~XM_PAUSE_MODE; + + skge_write16(hw, SK_REG(port, RX_MFF_CTRL1), MFF_DIS_PAUSE); + } + + xm_write32(hw, port, XM_MODE, mode); + + /* Turn on detection of Tx underrun */ + msk = xm_read16(hw, port, XM_IMSK); + msk &= ~XM_IS_TXF_UR; + xm_write16(hw, port, XM_IMSK, msk); + + xm_read16(hw, port, XM_ISRC); + + /* get MMU Command Reg. */ + cmd = xm_read16(hw, port, XM_MMU_CMD); + if (hw->phy_type != SK_PHY_XMAC && skge->duplex == DUPLEX_FULL) + cmd |= XM_MMU_GMII_FD; + + /* + * Workaround BCOM Errata (#10523) for all BCom Phys + * Enable Power Management after link up + */ + if (hw->phy_type == SK_PHY_BCOM) { + xm_phy_write(hw, port, PHY_BCOM_AUX_CTRL, + xm_phy_read(hw, port, PHY_BCOM_AUX_CTRL) + & ~PHY_B_AC_DIS_PM); + xm_phy_write(hw, port, PHY_BCOM_INT_MASK, PHY_B_DEF_MSK); + } + + /* enable Rx/Tx */ + xm_write16(hw, port, XM_MMU_CMD, + cmd | XM_MMU_ENA_RX | XM_MMU_ENA_TX); + skge_link_up(skge); +} + + +static inline void bcom_phy_intr(struct skge_port *skge) +{ + struct skge_hw *hw = skge->hw; + int port = skge->port; + u16 isrc; + + isrc = xm_phy_read(hw, port, PHY_BCOM_INT_STAT); + netif_printk(skge, intr, KERN_DEBUG, skge->netdev, + "phy interrupt status 0x%x\n", isrc); + + if (isrc & PHY_B_IS_PSE) + pr_err("%s: uncorrectable pair swap error\n", + hw->dev[port]->name); + + /* Workaround BCom Errata: + * enable and disable loopback mode if "NO HCD" occurs. + */ + if (isrc & PHY_B_IS_NO_HDCL) { + u16 ctrl = xm_phy_read(hw, port, PHY_BCOM_CTRL); + xm_phy_write(hw, port, PHY_BCOM_CTRL, + ctrl | PHY_CT_LOOP); + xm_phy_write(hw, port, PHY_BCOM_CTRL, + ctrl & ~PHY_CT_LOOP); + } + + if (isrc & (PHY_B_IS_AN_PR | PHY_B_IS_LST_CHANGE)) + bcom_check_link(hw, port); + +} + +static int gm_phy_write(struct skge_hw *hw, int port, u16 reg, u16 val) +{ + int i; + + gma_write16(hw, port, GM_SMI_DATA, val); + gma_write16(hw, port, GM_SMI_CTRL, + GM_SMI_CT_PHY_AD(hw->phy_addr) | GM_SMI_CT_REG_AD(reg)); + for (i = 0; i < PHY_RETRIES; i++) { + udelay(1); + + if (!(gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_BUSY)) + return 0; + } + + pr_warn("%s: phy write timeout\n", hw->dev[port]->name); + return -EIO; +} + +static int __gm_phy_read(struct skge_hw *hw, int port, u16 reg, u16 *val) +{ + int i; + + gma_write16(hw, port, GM_SMI_CTRL, + GM_SMI_CT_PHY_AD(hw->phy_addr) + | GM_SMI_CT_REG_AD(reg) | GM_SMI_CT_OP_RD); + + for (i = 0; i < PHY_RETRIES; i++) { + udelay(1); + if (gma_read16(hw, port, GM_SMI_CTRL) & GM_SMI_CT_RD_VAL) + goto ready; + } + + return -ETIMEDOUT; + ready: + *val = gma_read16(hw, port, GM_SMI_DATA); + return 0; +} + +static u16 gm_phy_read(struct skge_hw *hw, int port, u16 reg) +{ + u16 v = 0; + if (__gm_phy_read(hw, port, reg, &v)) + pr_warn("%s: phy read timeout\n", hw->dev[port]->name); + return v; +} + +/* Marvell Phy Initialization */ +static void yukon_init(struct skge_hw *hw, int port) +{ + struct skge_port *skge = netdev_priv(hw->dev[port]); + u16 ctrl, ct1000, adv; + + if (skge->autoneg == AUTONEG_ENABLE) { + u16 ectrl = gm_phy_read(hw, port, PHY_MARV_EXT_CTRL); + + ectrl &= ~(PHY_M_EC_M_DSC_MSK | PHY_M_EC_S_DSC_MSK | + PHY_M_EC_MAC_S_MSK); + ectrl |= PHY_M_EC_MAC_S(MAC_TX_CLK_25_MHZ); + + ectrl |= PHY_M_EC_M_DSC(0) | PHY_M_EC_S_DSC(1); + + gm_phy_write(hw, port, PHY_MARV_EXT_CTRL, ectrl); + } + + ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL); + if (skge->autoneg == AUTONEG_DISABLE) + ctrl &= ~PHY_CT_ANE; + + ctrl |= PHY_CT_RESET; + gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl); + + ctrl = 0; + ct1000 = 0; + adv = PHY_AN_CSMA; + + if (skge->autoneg == AUTONEG_ENABLE) { + if (hw->copper) { + if (skge->advertising & ADVERTISED_1000baseT_Full) + ct1000 |= PHY_M_1000C_AFD; + if (skge->advertising & ADVERTISED_1000baseT_Half) + ct1000 |= PHY_M_1000C_AHD; + if (skge->advertising & ADVERTISED_100baseT_Full) + adv |= PHY_M_AN_100_FD; + if (skge->advertising & ADVERTISED_100baseT_Half) + adv |= PHY_M_AN_100_HD; + if (skge->advertising & ADVERTISED_10baseT_Full) + adv |= PHY_M_AN_10_FD; + if (skge->advertising & ADVERTISED_10baseT_Half) + adv |= PHY_M_AN_10_HD; + + /* Set Flow-control capabilities */ + adv |= phy_pause_map[skge->flow_control]; + } else { + if (skge->advertising & ADVERTISED_1000baseT_Full) + adv |= PHY_M_AN_1000X_AFD; + if (skge->advertising & ADVERTISED_1000baseT_Half) + adv |= PHY_M_AN_1000X_AHD; + + adv |= fiber_pause_map[skge->flow_control]; + } + + /* Restart Auto-negotiation */ + ctrl |= PHY_CT_ANE | PHY_CT_RE_CFG; + } else { + /* forced speed/duplex settings */ + ct1000 = PHY_M_1000C_MSE; + + if (skge->duplex == DUPLEX_FULL) + ctrl |= PHY_CT_DUP_MD; + + switch (skge->speed) { + case SPEED_1000: + ctrl |= PHY_CT_SP1000; + break; + case SPEED_100: + ctrl |= PHY_CT_SP100; + break; + } + + ctrl |= PHY_CT_RESET; + } + + gm_phy_write(hw, port, PHY_MARV_1000T_CTRL, ct1000); + + gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, adv); + gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl); + + /* Enable phy interrupt on autonegotiation complete (or link up) */ + if (skge->autoneg == AUTONEG_ENABLE) + gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_AN_MSK); + else + gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_DEF_MSK); +} + +static void yukon_reset(struct skge_hw *hw, int port) +{ + gm_phy_write(hw, port, PHY_MARV_INT_MASK, 0);/* disable PHY IRQs */ + gma_write16(hw, port, GM_MC_ADDR_H1, 0); /* clear MC hash */ + gma_write16(hw, port, GM_MC_ADDR_H2, 0); + gma_write16(hw, port, GM_MC_ADDR_H3, 0); + gma_write16(hw, port, GM_MC_ADDR_H4, 0); + + gma_write16(hw, port, GM_RX_CTRL, + gma_read16(hw, port, GM_RX_CTRL) + | GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA); +} + +/* Apparently, early versions of Yukon-Lite had wrong chip_id? */ +static int is_yukon_lite_a0(struct skge_hw *hw) +{ + u32 reg; + int ret; + + if (hw->chip_id != CHIP_ID_YUKON) + return 0; + + reg = skge_read32(hw, B2_FAR); + skge_write8(hw, B2_FAR + 3, 0xff); + ret = (skge_read8(hw, B2_FAR + 3) != 0); + skge_write32(hw, B2_FAR, reg); + return ret; +} + +static void yukon_mac_init(struct skge_hw *hw, int port) +{ + struct skge_port *skge = netdev_priv(hw->dev[port]); + int i; + u32 reg; + const u8 *addr = hw->dev[port]->dev_addr; + + /* WA code for COMA mode -- set PHY reset */ + if (hw->chip_id == CHIP_ID_YUKON_LITE && + hw->chip_rev >= CHIP_REV_YU_LITE_A3) { + reg = skge_read32(hw, B2_GP_IO); + reg |= GP_DIR_9 | GP_IO_9; + skge_write32(hw, B2_GP_IO, reg); + } + + /* hard reset */ + skge_write32(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET); + skge_write32(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET); + + /* WA code for COMA mode -- clear PHY reset */ + if (hw->chip_id == CHIP_ID_YUKON_LITE && + hw->chip_rev >= CHIP_REV_YU_LITE_A3) { + reg = skge_read32(hw, B2_GP_IO); + reg |= GP_DIR_9; + reg &= ~GP_IO_9; + skge_write32(hw, B2_GP_IO, reg); + } + + /* Set hardware config mode */ + reg = GPC_INT_POL_HI | GPC_DIS_FC | GPC_DIS_SLEEP | + GPC_ENA_XC | GPC_ANEG_ADV_ALL_M | GPC_ENA_PAUSE; + reg |= hw->copper ? GPC_HWCFG_GMII_COP : GPC_HWCFG_GMII_FIB; + + /* Clear GMC reset */ + skge_write32(hw, SK_REG(port, GPHY_CTRL), reg | GPC_RST_SET); + skge_write32(hw, SK_REG(port, GPHY_CTRL), reg | GPC_RST_CLR); + skge_write32(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON | GMC_RST_CLR); + + if (skge->autoneg == AUTONEG_DISABLE) { + reg = GM_GPCR_AU_ALL_DIS; + gma_write16(hw, port, GM_GP_CTRL, + gma_read16(hw, port, GM_GP_CTRL) | reg); + + switch (skge->speed) { + case SPEED_1000: + reg &= ~GM_GPCR_SPEED_100; + reg |= GM_GPCR_SPEED_1000; + break; + case SPEED_100: + reg &= ~GM_GPCR_SPEED_1000; + reg |= GM_GPCR_SPEED_100; + break; + case SPEED_10: + reg &= ~(GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100); + break; + } + + if (skge->duplex == DUPLEX_FULL) + reg |= GM_GPCR_DUP_FULL; + } else + reg = GM_GPCR_SPEED_1000 | GM_GPCR_SPEED_100 | GM_GPCR_DUP_FULL; + + switch (skge->flow_control) { + case FLOW_MODE_NONE: + skge_write32(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF); + reg |= GM_GPCR_FC_TX_DIS | GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS; + break; + case FLOW_MODE_LOC_SEND: + /* disable Rx flow-control */ + reg |= GM_GPCR_FC_RX_DIS | GM_GPCR_AU_FCT_DIS; + break; + case FLOW_MODE_SYMMETRIC: + case FLOW_MODE_SYM_OR_REM: + /* enable Tx & Rx flow-control */ + break; + } + + gma_write16(hw, port, GM_GP_CTRL, reg); + skge_read16(hw, SK_REG(port, GMAC_IRQ_SRC)); + + yukon_init(hw, port); + + /* MIB clear */ + reg = gma_read16(hw, port, GM_PHY_ADDR); + gma_write16(hw, port, GM_PHY_ADDR, reg | GM_PAR_MIB_CLR); + + for (i = 0; i < GM_MIB_CNT_SIZE; i++) + gma_read16(hw, port, GM_MIB_CNT_BASE + 8*i); + gma_write16(hw, port, GM_PHY_ADDR, reg); + + /* transmit control */ + gma_write16(hw, port, GM_TX_CTRL, TX_COL_THR(TX_COL_DEF)); + + /* receive control reg: unicast + multicast + no FCS */ + gma_write16(hw, port, GM_RX_CTRL, + GM_RXCR_UCF_ENA | GM_RXCR_CRC_DIS | GM_RXCR_MCF_ENA); + + /* transmit flow control */ + gma_write16(hw, port, GM_TX_FLOW_CTRL, 0xffff); + + /* transmit parameter */ + gma_write16(hw, port, GM_TX_PARAM, + TX_JAM_LEN_VAL(TX_JAM_LEN_DEF) | + TX_JAM_IPG_VAL(TX_JAM_IPG_DEF) | + TX_IPG_JAM_DATA(TX_IPG_JAM_DEF)); + + /* configure the Serial Mode Register */ + reg = DATA_BLIND_VAL(DATA_BLIND_DEF) + | GM_SMOD_VLAN_ENA + | IPG_DATA_VAL(IPG_DATA_DEF); + + if (hw->dev[port]->mtu > ETH_DATA_LEN) + reg |= GM_SMOD_JUMBO_ENA; + + gma_write16(hw, port, GM_SERIAL_MODE, reg); + + /* physical address: used for pause frames */ + gma_set_addr(hw, port, GM_SRC_ADDR_1L, addr); + /* virtual address for data */ + gma_set_addr(hw, port, GM_SRC_ADDR_2L, addr); + + /* enable interrupt mask for counter overflows */ + gma_write16(hw, port, GM_TX_IRQ_MSK, 0); + gma_write16(hw, port, GM_RX_IRQ_MSK, 0); + gma_write16(hw, port, GM_TR_IRQ_MSK, 0); + + /* Initialize Mac Fifo */ + + /* Configure Rx MAC FIFO */ + skge_write16(hw, SK_REG(port, RX_GMF_FL_MSK), RX_FF_FL_DEF_MSK); + reg = GMF_OPER_ON | GMF_RX_F_FL_ON; + + /* disable Rx GMAC FIFO Flush for YUKON-Lite Rev. A0 only */ + if (is_yukon_lite_a0(hw)) + reg &= ~GMF_RX_F_FL_ON; + + skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR); + skge_write16(hw, SK_REG(port, RX_GMF_CTRL_T), reg); + /* + * because Pause Packet Truncation in GMAC is not working + * we have to increase the Flush Threshold to 64 bytes + * in order to flush pause packets in Rx FIFO on Yukon-1 + */ + skge_write16(hw, SK_REG(port, RX_GMF_FL_THR), RX_GMF_FL_THR_DEF+1); + + /* Configure Tx MAC FIFO */ + skge_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_CLR); + skge_write16(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_OPER_ON); +} + +/* Go into power down mode */ +static void yukon_suspend(struct skge_hw *hw, int port) +{ + u16 ctrl; + + ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL); + ctrl |= PHY_M_PC_POL_R_DIS; + gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl); + + ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL); + ctrl |= PHY_CT_RESET; + gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl); + + /* switch IEEE compatible power down mode on */ + ctrl = gm_phy_read(hw, port, PHY_MARV_CTRL); + ctrl |= PHY_CT_PDOWN; + gm_phy_write(hw, port, PHY_MARV_CTRL, ctrl); +} + +static void yukon_stop(struct skge_port *skge) +{ + struct skge_hw *hw = skge->hw; + int port = skge->port; + + skge_write8(hw, SK_REG(port, GMAC_IRQ_MSK), 0); + yukon_reset(hw, port); + + gma_write16(hw, port, GM_GP_CTRL, + gma_read16(hw, port, GM_GP_CTRL) + & ~(GM_GPCR_TX_ENA|GM_GPCR_RX_ENA)); + gma_read16(hw, port, GM_GP_CTRL); + + yukon_suspend(hw, port); + + /* set GPHY Control reset */ + skge_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_SET); + skge_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_SET); +} + +static void yukon_get_stats(struct skge_port *skge, u64 *data) +{ + struct skge_hw *hw = skge->hw; + int port = skge->port; + int i; + + data[0] = (u64) gma_read32(hw, port, GM_TXO_OK_HI) << 32 + | gma_read32(hw, port, GM_TXO_OK_LO); + data[1] = (u64) gma_read32(hw, port, GM_RXO_OK_HI) << 32 + | gma_read32(hw, port, GM_RXO_OK_LO); + + for (i = 2; i < ARRAY_SIZE(skge_stats); i++) + data[i] = gma_read32(hw, port, + skge_stats[i].gma_offset); +} + +static void yukon_mac_intr(struct skge_hw *hw, int port) +{ + struct net_device *dev = hw->dev[port]; + struct skge_port *skge = netdev_priv(dev); + u8 status = skge_read8(hw, SK_REG(port, GMAC_IRQ_SRC)); + + netif_printk(skge, intr, KERN_DEBUG, skge->netdev, + "mac interrupt status 0x%x\n", status); + + if (status & GM_IS_RX_FF_OR) { + ++dev->stats.rx_fifo_errors; + skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_CLI_RX_FO); + } + + if (status & GM_IS_TX_FF_UR) { + ++dev->stats.tx_fifo_errors; + skge_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_CLI_TX_FU); + } + +} + +static u16 yukon_speed(const struct skge_hw *hw, u16 aux) +{ + switch (aux & PHY_M_PS_SPEED_MSK) { + case PHY_M_PS_SPEED_1000: + return SPEED_1000; + case PHY_M_PS_SPEED_100: + return SPEED_100; + default: + return SPEED_10; + } +} + +static void yukon_link_up(struct skge_port *skge) +{ + struct skge_hw *hw = skge->hw; + int port = skge->port; + u16 reg; + + /* Enable Transmit FIFO Underrun */ + skge_write8(hw, SK_REG(port, GMAC_IRQ_MSK), GMAC_DEF_MSK); + + reg = gma_read16(hw, port, GM_GP_CTRL); + if (skge->duplex == DUPLEX_FULL || skge->autoneg == AUTONEG_ENABLE) + reg |= GM_GPCR_DUP_FULL; + + /* enable Rx/Tx */ + reg |= GM_GPCR_RX_ENA | GM_GPCR_TX_ENA; + gma_write16(hw, port, GM_GP_CTRL, reg); + + gm_phy_write(hw, port, PHY_MARV_INT_MASK, PHY_M_IS_DEF_MSK); + skge_link_up(skge); +} + +static void yukon_link_down(struct skge_port *skge) +{ + struct skge_hw *hw = skge->hw; + int port = skge->port; + u16 ctrl; + + ctrl = gma_read16(hw, port, GM_GP_CTRL); + ctrl &= ~(GM_GPCR_RX_ENA | GM_GPCR_TX_ENA); + gma_write16(hw, port, GM_GP_CTRL, ctrl); + + if (skge->flow_status == FLOW_STAT_REM_SEND) { + ctrl = gm_phy_read(hw, port, PHY_MARV_AUNE_ADV); + ctrl |= PHY_M_AN_ASP; + /* restore Asymmetric Pause bit */ + gm_phy_write(hw, port, PHY_MARV_AUNE_ADV, ctrl); + } + + skge_link_down(skge); + + yukon_init(hw, port); +} + +static void yukon_phy_intr(struct skge_port *skge) +{ + struct skge_hw *hw = skge->hw; + int port = skge->port; + const char *reason = NULL; + u16 istatus, phystat; + + istatus = gm_phy_read(hw, port, PHY_MARV_INT_STAT); + phystat = gm_phy_read(hw, port, PHY_MARV_PHY_STAT); + + netif_printk(skge, intr, KERN_DEBUG, skge->netdev, + "phy interrupt status 0x%x 0x%x\n", istatus, phystat); + + if (istatus & PHY_M_IS_AN_COMPL) { + if (gm_phy_read(hw, port, PHY_MARV_AUNE_LP) + & PHY_M_AN_RF) { + reason = "remote fault"; + goto failed; + } + + if (gm_phy_read(hw, port, PHY_MARV_1000T_STAT) & PHY_B_1000S_MSF) { + reason = "master/slave fault"; + goto failed; + } + + if (!(phystat & PHY_M_PS_SPDUP_RES)) { + reason = "speed/duplex"; + goto failed; + } + + skge->duplex = (phystat & PHY_M_PS_FULL_DUP) + ? DUPLEX_FULL : DUPLEX_HALF; + skge->speed = yukon_speed(hw, phystat); + + /* We are using IEEE 802.3z/D5.0 Table 37-4 */ + switch (phystat & PHY_M_PS_PAUSE_MSK) { + case PHY_M_PS_PAUSE_MSK: + skge->flow_status = FLOW_STAT_SYMMETRIC; + break; + case PHY_M_PS_RX_P_EN: + skge->flow_status = FLOW_STAT_REM_SEND; + break; + case PHY_M_PS_TX_P_EN: + skge->flow_status = FLOW_STAT_LOC_SEND; + break; + default: + skge->flow_status = FLOW_STAT_NONE; + } + + if (skge->flow_status == FLOW_STAT_NONE || + (skge->speed < SPEED_1000 && skge->duplex == DUPLEX_HALF)) + skge_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_OFF); + else + skge_write8(hw, SK_REG(port, GMAC_CTRL), GMC_PAUSE_ON); + yukon_link_up(skge); + return; + } + + if (istatus & PHY_M_IS_LSP_CHANGE) + skge->speed = yukon_speed(hw, phystat); + + if (istatus & PHY_M_IS_DUP_CHANGE) + skge->duplex = (phystat & PHY_M_PS_FULL_DUP) ? DUPLEX_FULL : DUPLEX_HALF; + if (istatus & PHY_M_IS_LST_CHANGE) { + if (phystat & PHY_M_PS_LINK_UP) + yukon_link_up(skge); + else + yukon_link_down(skge); + } + return; + failed: + pr_err("%s: autonegotiation failed (%s)\n", skge->netdev->name, reason); + + /* XXX restart autonegotiation? */ +} + +static void skge_phy_reset(struct skge_port *skge) +{ + struct skge_hw *hw = skge->hw; + int port = skge->port; + struct net_device *dev = hw->dev[port]; + + netif_stop_queue(skge->netdev); + netif_carrier_off(skge->netdev); + + spin_lock_bh(&hw->phy_lock); + if (is_genesis(hw)) { + genesis_reset(hw, port); + genesis_mac_init(hw, port); + } else { + yukon_reset(hw, port); + yukon_init(hw, port); + } + spin_unlock_bh(&hw->phy_lock); + + skge_set_multicast(dev); +} + +/* Basic MII support */ +static int skge_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) +{ + struct mii_ioctl_data *data = if_mii(ifr); + struct skge_port *skge = netdev_priv(dev); + struct skge_hw *hw = skge->hw; + int err = -EOPNOTSUPP; + + if (!netif_running(dev)) + return -ENODEV; /* Phy still in reset */ + + switch (cmd) { + case SIOCGMIIPHY: + data->phy_id = hw->phy_addr; + + fallthrough; + case SIOCGMIIREG: { + u16 val = 0; + spin_lock_bh(&hw->phy_lock); + + if (is_genesis(hw)) + err = __xm_phy_read(hw, skge->port, data->reg_num & 0x1f, &val); + else + err = __gm_phy_read(hw, skge->port, data->reg_num & 0x1f, &val); + spin_unlock_bh(&hw->phy_lock); + data->val_out = val; + break; + } + + case SIOCSMIIREG: + spin_lock_bh(&hw->phy_lock); + if (is_genesis(hw)) + err = xm_phy_write(hw, skge->port, data->reg_num & 0x1f, + data->val_in); + else + err = gm_phy_write(hw, skge->port, data->reg_num & 0x1f, + data->val_in); + spin_unlock_bh(&hw->phy_lock); + break; + } + return err; +} + +static void skge_ramset(struct skge_hw *hw, u16 q, u32 start, size_t len) +{ + u32 end; + + start /= 8; + len /= 8; + end = start + len - 1; + + skge_write8(hw, RB_ADDR(q, RB_CTRL), RB_RST_CLR); + skge_write32(hw, RB_ADDR(q, RB_START), start); + skge_write32(hw, RB_ADDR(q, RB_WP), start); + skge_write32(hw, RB_ADDR(q, RB_RP), start); + skge_write32(hw, RB_ADDR(q, RB_END), end); + + if (q == Q_R1 || q == Q_R2) { + /* Set thresholds on receive queue's */ + skge_write32(hw, RB_ADDR(q, RB_RX_UTPP), + start + (2*len)/3); + skge_write32(hw, RB_ADDR(q, RB_RX_LTPP), + start + (len/3)); + } else { + /* Enable store & forward on Tx queue's because + * Tx FIFO is only 4K on Genesis and 1K on Yukon + */ + skge_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_STFWD); + } + + skge_write8(hw, RB_ADDR(q, RB_CTRL), RB_ENA_OP_MD); +} + +/* Setup Bus Memory Interface */ +static void skge_qset(struct skge_port *skge, u16 q, + const struct skge_element *e) +{ + struct skge_hw *hw = skge->hw; + u32 watermark = 0x600; + u64 base = skge->dma + (e->desc - skge->mem); + + /* optimization to reduce window on 32bit/33mhz */ + if ((skge_read16(hw, B0_CTST) & (CS_BUS_CLOCK | CS_BUS_SLOT_SZ)) == 0) + watermark /= 2; + + skge_write32(hw, Q_ADDR(q, Q_CSR), CSR_CLR_RESET); + skge_write32(hw, Q_ADDR(q, Q_F), watermark); + skge_write32(hw, Q_ADDR(q, Q_DA_H), (u32)(base >> 32)); + skge_write32(hw, Q_ADDR(q, Q_DA_L), (u32)base); +} + +static int skge_up(struct net_device *dev) +{ + struct skge_port *skge = netdev_priv(dev); + struct skge_hw *hw = skge->hw; + int port = skge->port; + u32 chunk, ram_addr; + size_t rx_size, tx_size; + int err; + + if (!is_valid_ether_addr(dev->dev_addr)) + return -EINVAL; + + netif_info(skge, ifup, skge->netdev, "enabling interface\n"); + + if (dev->mtu > RX_BUF_SIZE) + skge->rx_buf_size = dev->mtu + ETH_HLEN; + else + skge->rx_buf_size = RX_BUF_SIZE; + + + rx_size = skge->rx_ring.count * sizeof(struct skge_rx_desc); + tx_size = skge->tx_ring.count * sizeof(struct skge_tx_desc); + skge->mem_size = tx_size + rx_size; + skge->mem = dma_alloc_coherent(&hw->pdev->dev, skge->mem_size, + &skge->dma, GFP_KERNEL); + if (!skge->mem) + return -ENOMEM; + + BUG_ON(skge->dma & 7); + + if (upper_32_bits(skge->dma) != upper_32_bits(skge->dma + skge->mem_size)) { + dev_err(&hw->pdev->dev, "dma_alloc_coherent region crosses 4G boundary\n"); + err = -EINVAL; + goto free_pci_mem; + } + + err = skge_ring_alloc(&skge->rx_ring, skge->mem, skge->dma); + if (err) + goto free_pci_mem; + + err = skge_rx_fill(dev); + if (err) + goto free_rx_ring; + + err = skge_ring_alloc(&skge->tx_ring, skge->mem + rx_size, + skge->dma + rx_size); + if (err) + goto free_rx_ring; + + if (hw->ports == 1) { + err = request_irq(hw->pdev->irq, skge_intr, IRQF_SHARED, + dev->name, hw); + if (err) { + netdev_err(dev, "Unable to allocate interrupt %d error: %d\n", + hw->pdev->irq, err); + goto free_tx_ring; + } + } + + /* Initialize MAC */ + netif_carrier_off(dev); + spin_lock_bh(&hw->phy_lock); + if (is_genesis(hw)) + genesis_mac_init(hw, port); + else + yukon_mac_init(hw, port); + spin_unlock_bh(&hw->phy_lock); + + /* Configure RAMbuffers - equally between ports and tx/rx */ + chunk = (hw->ram_size - hw->ram_offset) / (hw->ports * 2); + ram_addr = hw->ram_offset + 2 * chunk * port; + + skge_ramset(hw, rxqaddr[port], ram_addr, chunk); + skge_qset(skge, rxqaddr[port], skge->rx_ring.to_clean); + + BUG_ON(skge->tx_ring.to_use != skge->tx_ring.to_clean); + skge_ramset(hw, txqaddr[port], ram_addr+chunk, chunk); + skge_qset(skge, txqaddr[port], skge->tx_ring.to_use); + + /* Start receiver BMU */ + wmb(); + skge_write8(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_START | CSR_IRQ_CL_F); + skge_led(skge, LED_MODE_ON); + + spin_lock_irq(&hw->hw_lock); + hw->intr_mask |= portmask[port]; + skge_write32(hw, B0_IMSK, hw->intr_mask); + skge_read32(hw, B0_IMSK); + spin_unlock_irq(&hw->hw_lock); + + napi_enable(&skge->napi); + + skge_set_multicast(dev); + + return 0; + + free_tx_ring: + kfree(skge->tx_ring.start); + free_rx_ring: + skge_rx_clean(skge); + kfree(skge->rx_ring.start); + free_pci_mem: + dma_free_coherent(&hw->pdev->dev, skge->mem_size, skge->mem, + skge->dma); + skge->mem = NULL; + + return err; +} + +/* stop receiver */ +static void skge_rx_stop(struct skge_hw *hw, int port) +{ + skge_write8(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_STOP); + skge_write32(hw, RB_ADDR(port ? Q_R2 : Q_R1, RB_CTRL), + RB_RST_SET|RB_DIS_OP_MD); + skge_write32(hw, Q_ADDR(rxqaddr[port], Q_CSR), CSR_SET_RESET); +} + +static int skge_down(struct net_device *dev) +{ + struct skge_port *skge = netdev_priv(dev); + struct skge_hw *hw = skge->hw; + int port = skge->port; + + if (!skge->mem) + return 0; + + netif_info(skge, ifdown, skge->netdev, "disabling interface\n"); + + netif_tx_disable(dev); + + if (is_genesis(hw) && hw->phy_type == SK_PHY_XMAC) + del_timer_sync(&skge->link_timer); + + napi_disable(&skge->napi); + netif_carrier_off(dev); + + spin_lock_irq(&hw->hw_lock); + hw->intr_mask &= ~portmask[port]; + skge_write32(hw, B0_IMSK, (hw->ports == 1) ? 0 : hw->intr_mask); + skge_read32(hw, B0_IMSK); + spin_unlock_irq(&hw->hw_lock); + + if (hw->ports == 1) + free_irq(hw->pdev->irq, hw); + + skge_write8(skge->hw, SK_REG(skge->port, LNK_LED_REG), LED_REG_OFF); + if (is_genesis(hw)) + genesis_stop(skge); + else + yukon_stop(skge); + + /* Stop transmitter */ + skge_write8(hw, Q_ADDR(txqaddr[port], Q_CSR), CSR_STOP); + skge_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL), + RB_RST_SET|RB_DIS_OP_MD); + + + /* Disable Force Sync bit and Enable Alloc bit */ + skge_write8(hw, SK_REG(port, TXA_CTRL), + TXA_DIS_FSYNC | TXA_DIS_ALLOC | TXA_STOP_RC); + + /* Stop Interval Timer and Limit Counter of Tx Arbiter */ + skge_write32(hw, SK_REG(port, TXA_ITI_INI), 0L); + skge_write32(hw, SK_REG(port, TXA_LIM_INI), 0L); + + /* Reset PCI FIFO */ + skge_write32(hw, Q_ADDR(txqaddr[port], Q_CSR), CSR_SET_RESET); + skge_write32(hw, RB_ADDR(txqaddr[port], RB_CTRL), RB_RST_SET); + + /* Reset the RAM Buffer async Tx queue */ + skge_write8(hw, RB_ADDR(port == 0 ? Q_XA1 : Q_XA2, RB_CTRL), RB_RST_SET); + + skge_rx_stop(hw, port); + + if (is_genesis(hw)) { + skge_write8(hw, SK_REG(port, TX_MFF_CTRL2), MFF_RST_SET); + skge_write8(hw, SK_REG(port, RX_MFF_CTRL2), MFF_RST_SET); + } else { + skge_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_SET); + skge_write8(hw, SK_REG(port, TX_GMF_CTRL_T), GMF_RST_SET); + } + + skge_led(skge, LED_MODE_OFF); + + netif_tx_lock_bh(dev); + skge_tx_clean(dev); + netif_tx_unlock_bh(dev); + + skge_rx_clean(skge); + + kfree(skge->rx_ring.start); + kfree(skge->tx_ring.start); + dma_free_coherent(&hw->pdev->dev, skge->mem_size, skge->mem, + skge->dma); + skge->mem = NULL; + return 0; +} + +static inline int skge_avail(const struct skge_ring *ring) +{ + smp_mb(); + return ((ring->to_clean > ring->to_use) ? 0 : ring->count) + + (ring->to_clean - ring->to_use) - 1; +} + +static netdev_tx_t skge_xmit_frame(struct sk_buff *skb, + struct net_device *dev) +{ + struct skge_port *skge = netdev_priv(dev); + struct skge_hw *hw = skge->hw; + struct skge_element *e; + struct skge_tx_desc *td; + int i; + u32 control, len; + dma_addr_t map; + + if (skb_padto(skb, ETH_ZLEN)) + return NETDEV_TX_OK; + + if (unlikely(skge_avail(&skge->tx_ring) < skb_shinfo(skb)->nr_frags + 1)) + return NETDEV_TX_BUSY; + + e = skge->tx_ring.to_use; + td = e->desc; + BUG_ON(td->control & BMU_OWN); + e->skb = skb; + len = skb_headlen(skb); + map = dma_map_single(&hw->pdev->dev, skb->data, len, DMA_TO_DEVICE); + if (dma_mapping_error(&hw->pdev->dev, map)) + goto mapping_error; + + dma_unmap_addr_set(e, mapaddr, map); + dma_unmap_len_set(e, maplen, len); + + td->dma_lo = lower_32_bits(map); + td->dma_hi = upper_32_bits(map); + + if (skb->ip_summed == CHECKSUM_PARTIAL) { + const int offset = skb_checksum_start_offset(skb); + + /* This seems backwards, but it is what the sk98lin + * does. Looks like hardware is wrong? + */ + if (ipip_hdr(skb)->protocol == IPPROTO_UDP && + hw->chip_rev == 0 && hw->chip_id == CHIP_ID_YUKON) + control = BMU_TCP_CHECK; + else + control = BMU_UDP_CHECK; + + td->csum_offs = 0; + td->csum_start = offset; + td->csum_write = offset + skb->csum_offset; + } else + control = BMU_CHECK; + + if (!skb_shinfo(skb)->nr_frags) /* single buffer i.e. no fragments */ + control |= BMU_EOF | BMU_IRQ_EOF; + else { + struct skge_tx_desc *tf = td; + + control |= BMU_STFWD; + for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) { + const skb_frag_t *frag = &skb_shinfo(skb)->frags[i]; + + map = skb_frag_dma_map(&hw->pdev->dev, frag, 0, + skb_frag_size(frag), DMA_TO_DEVICE); + if (dma_mapping_error(&hw->pdev->dev, map)) + goto mapping_unwind; + + e = e->next; + e->skb = skb; + tf = e->desc; + BUG_ON(tf->control & BMU_OWN); + + tf->dma_lo = lower_32_bits(map); + tf->dma_hi = upper_32_bits(map); + dma_unmap_addr_set(e, mapaddr, map); + dma_unmap_len_set(e, maplen, skb_frag_size(frag)); + + tf->control = BMU_OWN | BMU_SW | control | skb_frag_size(frag); + } + tf->control |= BMU_EOF | BMU_IRQ_EOF; + } + /* Make sure all the descriptors written */ + wmb(); + td->control = BMU_OWN | BMU_SW | BMU_STF | control | len; + wmb(); + + netdev_sent_queue(dev, skb->len); + + skge_write8(hw, Q_ADDR(txqaddr[skge->port], Q_CSR), CSR_START); + + netif_printk(skge, tx_queued, KERN_DEBUG, skge->netdev, + "tx queued, slot %td, len %d\n", + e - skge->tx_ring.start, skb->len); + + skge->tx_ring.to_use = e->next; + smp_wmb(); + + if (skge_avail(&skge->tx_ring) <= TX_LOW_WATER) { + netdev_dbg(dev, "transmit queue full\n"); + netif_stop_queue(dev); + } + + return NETDEV_TX_OK; + +mapping_unwind: + e = skge->tx_ring.to_use; + dma_unmap_single(&hw->pdev->dev, dma_unmap_addr(e, mapaddr), + dma_unmap_len(e, maplen), DMA_TO_DEVICE); + while (i-- > 0) { + e = e->next; + dma_unmap_page(&hw->pdev->dev, dma_unmap_addr(e, mapaddr), + dma_unmap_len(e, maplen), DMA_TO_DEVICE); + } + +mapping_error: + if (net_ratelimit()) + dev_warn(&hw->pdev->dev, "%s: tx mapping error\n", dev->name); + dev_kfree_skb_any(skb); + return NETDEV_TX_OK; +} + + +/* Free resources associated with this reing element */ +static inline void skge_tx_unmap(struct pci_dev *pdev, struct skge_element *e, + u32 control) +{ + /* skb header vs. fragment */ + if (control & BMU_STF) + dma_unmap_single(&pdev->dev, dma_unmap_addr(e, mapaddr), + dma_unmap_len(e, maplen), DMA_TO_DEVICE); + else + dma_unmap_page(&pdev->dev, dma_unmap_addr(e, mapaddr), + dma_unmap_len(e, maplen), DMA_TO_DEVICE); +} + +/* Free all buffers in transmit ring */ +static void skge_tx_clean(struct net_device *dev) +{ + struct skge_port *skge = netdev_priv(dev); + struct skge_element *e; + + for (e = skge->tx_ring.to_clean; e != skge->tx_ring.to_use; e = e->next) { + struct skge_tx_desc *td = e->desc; + + skge_tx_unmap(skge->hw->pdev, e, td->control); + + if (td->control & BMU_EOF) + dev_kfree_skb(e->skb); + td->control = 0; + } + + netdev_reset_queue(dev); + skge->tx_ring.to_clean = e; +} + +static void skge_tx_timeout(struct net_device *dev, unsigned int txqueue) +{ + struct skge_port *skge = netdev_priv(dev); + + netif_printk(skge, timer, KERN_DEBUG, skge->netdev, "tx timeout\n"); + + skge_write8(skge->hw, Q_ADDR(txqaddr[skge->port], Q_CSR), CSR_STOP); + skge_tx_clean(dev); + netif_wake_queue(dev); +} + +static int skge_change_mtu(struct net_device *dev, int new_mtu) +{ + int err; + + if (!netif_running(dev)) { + dev->mtu = new_mtu; + return 0; + } + + skge_down(dev); + + dev->mtu = new_mtu; + + err = skge_up(dev); + if (err) + dev_close(dev); + + return err; +} + +static const u8 pause_mc_addr[ETH_ALEN] = { 0x1, 0x80, 0xc2, 0x0, 0x0, 0x1 }; + +static void genesis_add_filter(u8 filter[8], const u8 *addr) +{ + u32 crc, bit; + + crc = ether_crc_le(ETH_ALEN, addr); + bit = ~crc & 0x3f; + filter[bit/8] |= 1 << (bit%8); +} + +static void genesis_set_multicast(struct net_device *dev) +{ + struct skge_port *skge = netdev_priv(dev); + struct skge_hw *hw = skge->hw; + int port = skge->port; + struct netdev_hw_addr *ha; + u32 mode; + u8 filter[8]; + + mode = xm_read32(hw, port, XM_MODE); + mode |= XM_MD_ENA_HASH; + if (dev->flags & IFF_PROMISC) + mode |= XM_MD_ENA_PROM; + else + mode &= ~XM_MD_ENA_PROM; + + if (dev->flags & IFF_ALLMULTI) + memset(filter, 0xff, sizeof(filter)); + else { + memset(filter, 0, sizeof(filter)); + + if (skge->flow_status == FLOW_STAT_REM_SEND || + skge->flow_status == FLOW_STAT_SYMMETRIC) + genesis_add_filter(filter, pause_mc_addr); + + netdev_for_each_mc_addr(ha, dev) + genesis_add_filter(filter, ha->addr); + } + + xm_write32(hw, port, XM_MODE, mode); + xm_outhash(hw, port, XM_HSM, filter); +} + +static void yukon_add_filter(u8 filter[8], const u8 *addr) +{ + u32 bit = ether_crc(ETH_ALEN, addr) & 0x3f; + + filter[bit / 8] |= 1 << (bit % 8); +} + +static void yukon_set_multicast(struct net_device *dev) +{ + struct skge_port *skge = netdev_priv(dev); + struct skge_hw *hw = skge->hw; + int port = skge->port; + struct netdev_hw_addr *ha; + int rx_pause = (skge->flow_status == FLOW_STAT_REM_SEND || + skge->flow_status == FLOW_STAT_SYMMETRIC); + u16 reg; + u8 filter[8]; + + memset(filter, 0, sizeof(filter)); + + reg = gma_read16(hw, port, GM_RX_CTRL); + reg |= GM_RXCR_UCF_ENA; + + if (dev->flags & IFF_PROMISC) /* promiscuous */ + reg &= ~(GM_RXCR_UCF_ENA | GM_RXCR_MCF_ENA); + else if (dev->flags & IFF_ALLMULTI) /* all multicast */ + memset(filter, 0xff, sizeof(filter)); + else if (netdev_mc_empty(dev) && !rx_pause)/* no multicast */ + reg &= ~GM_RXCR_MCF_ENA; + else { + reg |= GM_RXCR_MCF_ENA; + + if (rx_pause) + yukon_add_filter(filter, pause_mc_addr); + + netdev_for_each_mc_addr(ha, dev) + yukon_add_filter(filter, ha->addr); + } + + + gma_write16(hw, port, GM_MC_ADDR_H1, + (u16)filter[0] | ((u16)filter[1] << 8)); + gma_write16(hw, port, GM_MC_ADDR_H2, + (u16)filter[2] | ((u16)filter[3] << 8)); + gma_write16(hw, port, GM_MC_ADDR_H3, + (u16)filter[4] | ((u16)filter[5] << 8)); + gma_write16(hw, port, GM_MC_ADDR_H4, + (u16)filter[6] | ((u16)filter[7] << 8)); + + gma_write16(hw, port, GM_RX_CTRL, reg); +} + +static inline u16 phy_length(const struct skge_hw *hw, u32 status) +{ + if (is_genesis(hw)) + return status >> XMR_FS_LEN_SHIFT; + else + return status >> GMR_FS_LEN_SHIFT; +} + +static inline int bad_phy_status(const struct skge_hw *hw, u32 status) +{ + if (is_genesis(hw)) + return (status & (XMR_FS_ERR | XMR_FS_2L_VLAN)) != 0; + else + return (status & GMR_FS_ANY_ERR) || + (status & GMR_FS_RX_OK) == 0; +} + +static void skge_set_multicast(struct net_device *dev) +{ + struct skge_port *skge = netdev_priv(dev); + + if (is_genesis(skge->hw)) + genesis_set_multicast(dev); + else + yukon_set_multicast(dev); + +} + + +/* Get receive buffer from descriptor. + * Handles copy of small buffers and reallocation failures + */ +static struct sk_buff *skge_rx_get(struct net_device *dev, + struct skge_element *e, + u32 control, u32 status, u16 csum) +{ + struct skge_port *skge = netdev_priv(dev); + struct sk_buff *skb; + u16 len = control & BMU_BBC; + + netif_printk(skge, rx_status, KERN_DEBUG, skge->netdev, + "rx slot %td status 0x%x len %d\n", + e - skge->rx_ring.start, status, len); + + if (len > skge->rx_buf_size) + goto error; + + if ((control & (BMU_EOF|BMU_STF)) != (BMU_STF|BMU_EOF)) + goto error; + + if (bad_phy_status(skge->hw, status)) + goto error; + + if (phy_length(skge->hw, status) != len) + goto error; + + if (len < RX_COPY_THRESHOLD) { + skb = netdev_alloc_skb_ip_align(dev, len); + if (!skb) + goto resubmit; + + dma_sync_single_for_cpu(&skge->hw->pdev->dev, + dma_unmap_addr(e, mapaddr), + dma_unmap_len(e, maplen), + DMA_FROM_DEVICE); + skb_copy_from_linear_data(e->skb, skb->data, len); + dma_sync_single_for_device(&skge->hw->pdev->dev, + dma_unmap_addr(e, mapaddr), + dma_unmap_len(e, maplen), + DMA_FROM_DEVICE); + skge_rx_reuse(e, skge->rx_buf_size); + } else { + struct skge_element ee; + struct sk_buff *nskb; + + nskb = netdev_alloc_skb_ip_align(dev, skge->rx_buf_size); + if (!nskb) + goto resubmit; + + ee = *e; + + skb = ee.skb; + prefetch(skb->data); + + if (skge_rx_setup(skge, e, nskb, skge->rx_buf_size) < 0) { + dev_kfree_skb(nskb); + goto resubmit; + } + + dma_unmap_single(&skge->hw->pdev->dev, + dma_unmap_addr(&ee, mapaddr), + dma_unmap_len(&ee, maplen), DMA_FROM_DEVICE); + } + + skb_put(skb, len); + + if (dev->features & NETIF_F_RXCSUM) { + skb->csum = le16_to_cpu(csum); + skb->ip_summed = CHECKSUM_COMPLETE; + } + + skb->protocol = eth_type_trans(skb, dev); + + return skb; +error: + + netif_printk(skge, rx_err, KERN_DEBUG, skge->netdev, + "rx err, slot %td control 0x%x status 0x%x\n", + e - skge->rx_ring.start, control, status); + + if (is_genesis(skge->hw)) { + if (status & (XMR_FS_RUNT|XMR_FS_LNG_ERR)) + dev->stats.rx_length_errors++; + if (status & XMR_FS_FRA_ERR) + dev->stats.rx_frame_errors++; + if (status & XMR_FS_FCS_ERR) + dev->stats.rx_crc_errors++; + } else { + if (status & (GMR_FS_LONG_ERR|GMR_FS_UN_SIZE)) + dev->stats.rx_length_errors++; + if (status & GMR_FS_FRAGMENT) + dev->stats.rx_frame_errors++; + if (status & GMR_FS_CRC_ERR) + dev->stats.rx_crc_errors++; + } + +resubmit: + skge_rx_reuse(e, skge->rx_buf_size); + return NULL; +} + +/* Free all buffers in Tx ring which are no longer owned by device */ +static void skge_tx_done(struct net_device *dev) +{ + struct skge_port *skge = netdev_priv(dev); + struct skge_ring *ring = &skge->tx_ring; + struct skge_element *e; + unsigned int bytes_compl = 0, pkts_compl = 0; + + skge_write8(skge->hw, Q_ADDR(txqaddr[skge->port], Q_CSR), CSR_IRQ_CL_F); + + for (e = ring->to_clean; e != ring->to_use; e = e->next) { + u32 control = ((const struct skge_tx_desc *) e->desc)->control; + + if (control & BMU_OWN) + break; + + skge_tx_unmap(skge->hw->pdev, e, control); + + if (control & BMU_EOF) { + netif_printk(skge, tx_done, KERN_DEBUG, skge->netdev, + "tx done slot %td\n", + e - skge->tx_ring.start); + + pkts_compl++; + bytes_compl += e->skb->len; + + dev_consume_skb_any(e->skb); + } + } + netdev_completed_queue(dev, pkts_compl, bytes_compl); + skge->tx_ring.to_clean = e; + + /* Can run lockless until we need to synchronize to restart queue. */ + smp_mb(); + + if (unlikely(netif_queue_stopped(dev) && + skge_avail(&skge->tx_ring) > TX_LOW_WATER)) { + netif_tx_lock(dev); + if (unlikely(netif_queue_stopped(dev) && + skge_avail(&skge->tx_ring) > TX_LOW_WATER)) { + netif_wake_queue(dev); + + } + netif_tx_unlock(dev); + } +} + +static int skge_poll(struct napi_struct *napi, int budget) +{ + struct skge_port *skge = container_of(napi, struct skge_port, napi); + struct net_device *dev = skge->netdev; + struct skge_hw *hw = skge->hw; + struct skge_ring *ring = &skge->rx_ring; + struct skge_element *e; + int work_done = 0; + + skge_tx_done(dev); + + skge_write8(hw, Q_ADDR(rxqaddr[skge->port], Q_CSR), CSR_IRQ_CL_F); + + for (e = ring->to_clean; prefetch(e->next), work_done < budget; e = e->next) { + struct skge_rx_desc *rd = e->desc; + struct sk_buff *skb; + u32 control; + + rmb(); + control = rd->control; + if (control & BMU_OWN) + break; + + skb = skge_rx_get(dev, e, control, rd->status, rd->csum2); + if (likely(skb)) { + napi_gro_receive(napi, skb); + ++work_done; + } + } + ring->to_clean = e; + + /* restart receiver */ + wmb(); + skge_write8(hw, Q_ADDR(rxqaddr[skge->port], Q_CSR), CSR_START); + + if (work_done < budget && napi_complete_done(napi, work_done)) { + unsigned long flags; + + spin_lock_irqsave(&hw->hw_lock, flags); + hw->intr_mask |= napimask[skge->port]; + skge_write32(hw, B0_IMSK, hw->intr_mask); + skge_read32(hw, B0_IMSK); + spin_unlock_irqrestore(&hw->hw_lock, flags); + } + + return work_done; +} + +/* Parity errors seem to happen when Genesis is connected to a switch + * with no other ports present. Heartbeat error?? + */ +static void skge_mac_parity(struct skge_hw *hw, int port) +{ + struct net_device *dev = hw->dev[port]; + + ++dev->stats.tx_heartbeat_errors; + + if (is_genesis(hw)) + skge_write16(hw, SK_REG(port, TX_MFF_CTRL1), + MFF_CLR_PERR); + else + /* HW-Bug #8: cleared by GMF_CLI_TX_FC instead of GMF_CLI_TX_PE */ + skge_write8(hw, SK_REG(port, TX_GMF_CTRL_T), + (hw->chip_id == CHIP_ID_YUKON && hw->chip_rev == 0) + ? GMF_CLI_TX_FC : GMF_CLI_TX_PE); +} + +static void skge_mac_intr(struct skge_hw *hw, int port) +{ + if (is_genesis(hw)) + genesis_mac_intr(hw, port); + else + yukon_mac_intr(hw, port); +} + +/* Handle device specific framing and timeout interrupts */ +static void skge_error_irq(struct skge_hw *hw) +{ + struct pci_dev *pdev = hw->pdev; + u32 hwstatus = skge_read32(hw, B0_HWE_ISRC); + + if (is_genesis(hw)) { + /* clear xmac errors */ + if (hwstatus & (IS_NO_STAT_M1|IS_NO_TIST_M1)) + skge_write16(hw, RX_MFF_CTRL1, MFF_CLR_INSTAT); + if (hwstatus & (IS_NO_STAT_M2|IS_NO_TIST_M2)) + skge_write16(hw, RX_MFF_CTRL2, MFF_CLR_INSTAT); + } else { + /* Timestamp (unused) overflow */ + if (hwstatus & IS_IRQ_TIST_OV) + skge_write8(hw, GMAC_TI_ST_CTRL, GMT_ST_CLR_IRQ); + } + + if (hwstatus & IS_RAM_RD_PAR) { + dev_err(&pdev->dev, "Ram read data parity error\n"); + skge_write16(hw, B3_RI_CTRL, RI_CLR_RD_PERR); + } + + if (hwstatus & IS_RAM_WR_PAR) { + dev_err(&pdev->dev, "Ram write data parity error\n"); + skge_write16(hw, B3_RI_CTRL, RI_CLR_WR_PERR); + } + + if (hwstatus & IS_M1_PAR_ERR) + skge_mac_parity(hw, 0); + + if (hwstatus & IS_M2_PAR_ERR) + skge_mac_parity(hw, 1); + + if (hwstatus & IS_R1_PAR_ERR) { + dev_err(&pdev->dev, "%s: receive queue parity error\n", + hw->dev[0]->name); + skge_write32(hw, B0_R1_CSR, CSR_IRQ_CL_P); + } + + if (hwstatus & IS_R2_PAR_ERR) { + dev_err(&pdev->dev, "%s: receive queue parity error\n", + hw->dev[1]->name); + skge_write32(hw, B0_R2_CSR, CSR_IRQ_CL_P); + } + + if (hwstatus & (IS_IRQ_MST_ERR|IS_IRQ_STAT)) { + u16 pci_status, pci_cmd; + + pci_read_config_word(pdev, PCI_COMMAND, &pci_cmd); + pci_read_config_word(pdev, PCI_STATUS, &pci_status); + + dev_err(&pdev->dev, "PCI error cmd=%#x status=%#x\n", + pci_cmd, pci_status); + + /* Write the error bits back to clear them. */ + pci_status &= PCI_STATUS_ERROR_BITS; + skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); + pci_write_config_word(pdev, PCI_COMMAND, + pci_cmd | PCI_COMMAND_SERR | PCI_COMMAND_PARITY); + pci_write_config_word(pdev, PCI_STATUS, pci_status); + skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); + + /* if error still set then just ignore it */ + hwstatus = skge_read32(hw, B0_HWE_ISRC); + if (hwstatus & IS_IRQ_STAT) { + dev_warn(&hw->pdev->dev, "unable to clear error (so ignoring them)\n"); + hw->intr_mask &= ~IS_HW_ERR; + } + } +} + +/* + * Interrupt from PHY are handled in tasklet (softirq) + * because accessing phy registers requires spin wait which might + * cause excess interrupt latency. + */ +static void skge_extirq(struct tasklet_struct *t) +{ + struct skge_hw *hw = from_tasklet(hw, t, phy_task); + int port; + + for (port = 0; port < hw->ports; port++) { + struct net_device *dev = hw->dev[port]; + + if (netif_running(dev)) { + struct skge_port *skge = netdev_priv(dev); + + spin_lock(&hw->phy_lock); + if (!is_genesis(hw)) + yukon_phy_intr(skge); + else if (hw->phy_type == SK_PHY_BCOM) + bcom_phy_intr(skge); + spin_unlock(&hw->phy_lock); + } + } + + spin_lock_irq(&hw->hw_lock); + hw->intr_mask |= IS_EXT_REG; + skge_write32(hw, B0_IMSK, hw->intr_mask); + skge_read32(hw, B0_IMSK); + spin_unlock_irq(&hw->hw_lock); +} + +static irqreturn_t skge_intr(int irq, void *dev_id) +{ + struct skge_hw *hw = dev_id; + u32 status; + int handled = 0; + + spin_lock(&hw->hw_lock); + /* Reading this register masks IRQ */ + status = skge_read32(hw, B0_SP_ISRC); + if (status == 0 || status == ~0) + goto out; + + handled = 1; + status &= hw->intr_mask; + if (status & IS_EXT_REG) { + hw->intr_mask &= ~IS_EXT_REG; + tasklet_schedule(&hw->phy_task); + } + + if (status & (IS_XA1_F|IS_R1_F)) { + struct skge_port *skge = netdev_priv(hw->dev[0]); + hw->intr_mask &= ~(IS_XA1_F|IS_R1_F); + napi_schedule(&skge->napi); + } + + if (status & IS_PA_TO_TX1) + skge_write16(hw, B3_PA_CTRL, PA_CLR_TO_TX1); + + if (status & IS_PA_TO_RX1) { + ++hw->dev[0]->stats.rx_over_errors; + skge_write16(hw, B3_PA_CTRL, PA_CLR_TO_RX1); + } + + + if (status & IS_MAC1) + skge_mac_intr(hw, 0); + + if (hw->dev[1]) { + struct skge_port *skge = netdev_priv(hw->dev[1]); + + if (status & (IS_XA2_F|IS_R2_F)) { + hw->intr_mask &= ~(IS_XA2_F|IS_R2_F); + napi_schedule(&skge->napi); + } + + if (status & IS_PA_TO_RX2) { + ++hw->dev[1]->stats.rx_over_errors; + skge_write16(hw, B3_PA_CTRL, PA_CLR_TO_RX2); + } + + if (status & IS_PA_TO_TX2) + skge_write16(hw, B3_PA_CTRL, PA_CLR_TO_TX2); + + if (status & IS_MAC2) + skge_mac_intr(hw, 1); + } + + if (status & IS_HW_ERR) + skge_error_irq(hw); +out: + skge_write32(hw, B0_IMSK, hw->intr_mask); + skge_read32(hw, B0_IMSK); + spin_unlock(&hw->hw_lock); + + return IRQ_RETVAL(handled); +} + +#ifdef CONFIG_NET_POLL_CONTROLLER +static void skge_netpoll(struct net_device *dev) +{ + struct skge_port *skge = netdev_priv(dev); + + disable_irq(dev->irq); + skge_intr(dev->irq, skge->hw); + enable_irq(dev->irq); +} +#endif + +static int skge_set_mac_address(struct net_device *dev, void *p) +{ + struct skge_port *skge = netdev_priv(dev); + struct skge_hw *hw = skge->hw; + unsigned port = skge->port; + const struct sockaddr *addr = p; + u16 ctrl; + + if (!is_valid_ether_addr(addr->sa_data)) + return -EADDRNOTAVAIL; + + eth_hw_addr_set(dev, addr->sa_data); + + if (!netif_running(dev)) { + memcpy_toio(hw->regs + B2_MAC_1 + port*8, dev->dev_addr, ETH_ALEN); + memcpy_toio(hw->regs + B2_MAC_2 + port*8, dev->dev_addr, ETH_ALEN); + } else { + /* disable Rx */ + spin_lock_bh(&hw->phy_lock); + ctrl = gma_read16(hw, port, GM_GP_CTRL); + gma_write16(hw, port, GM_GP_CTRL, ctrl & ~GM_GPCR_RX_ENA); + + memcpy_toio(hw->regs + B2_MAC_1 + port*8, dev->dev_addr, ETH_ALEN); + memcpy_toio(hw->regs + B2_MAC_2 + port*8, dev->dev_addr, ETH_ALEN); + + if (is_genesis(hw)) + xm_outaddr(hw, port, XM_SA, dev->dev_addr); + else { + gma_set_addr(hw, port, GM_SRC_ADDR_1L, dev->dev_addr); + gma_set_addr(hw, port, GM_SRC_ADDR_2L, dev->dev_addr); + } + + gma_write16(hw, port, GM_GP_CTRL, ctrl); + spin_unlock_bh(&hw->phy_lock); + } + + return 0; +} + +static const struct { + u8 id; + const char *name; +} skge_chips[] = { + { CHIP_ID_GENESIS, "Genesis" }, + { CHIP_ID_YUKON, "Yukon" }, + { CHIP_ID_YUKON_LITE, "Yukon-Lite"}, + { CHIP_ID_YUKON_LP, "Yukon-LP"}, +}; + +static const char *skge_board_name(const struct skge_hw *hw) +{ + int i; + static char buf[16]; + + for (i = 0; i < ARRAY_SIZE(skge_chips); i++) + if (skge_chips[i].id == hw->chip_id) + return skge_chips[i].name; + + snprintf(buf, sizeof(buf), "chipid 0x%x", hw->chip_id); + return buf; +} + + +/* + * Setup the board data structure, but don't bring up + * the port(s) + */ +static int skge_reset(struct skge_hw *hw) +{ + u32 reg; + u16 ctst, pci_status; + u8 t8, mac_cfg, pmd_type; + int i; + + ctst = skge_read16(hw, B0_CTST); + + /* do a SW reset */ + skge_write8(hw, B0_CTST, CS_RST_SET); + skge_write8(hw, B0_CTST, CS_RST_CLR); + + /* clear PCI errors, if any */ + skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); + skge_write8(hw, B2_TST_CTRL2, 0); + + pci_read_config_word(hw->pdev, PCI_STATUS, &pci_status); + pci_write_config_word(hw->pdev, PCI_STATUS, + pci_status | PCI_STATUS_ERROR_BITS); + skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); + skge_write8(hw, B0_CTST, CS_MRST_CLR); + + /* restore CLK_RUN bits (for Yukon-Lite) */ + skge_write16(hw, B0_CTST, + ctst & (CS_CLK_RUN_HOT|CS_CLK_RUN_RST|CS_CLK_RUN_ENA)); + + hw->chip_id = skge_read8(hw, B2_CHIP_ID); + hw->phy_type = skge_read8(hw, B2_E_1) & 0xf; + pmd_type = skge_read8(hw, B2_PMD_TYP); + hw->copper = (pmd_type == 'T' || pmd_type == '1'); + + switch (hw->chip_id) { + case CHIP_ID_GENESIS: +#ifdef CONFIG_SKGE_GENESIS + switch (hw->phy_type) { + case SK_PHY_XMAC: + hw->phy_addr = PHY_ADDR_XMAC; + break; + case SK_PHY_BCOM: + hw->phy_addr = PHY_ADDR_BCOM; + break; + default: + dev_err(&hw->pdev->dev, "unsupported phy type 0x%x\n", + hw->phy_type); + return -EOPNOTSUPP; + } + break; +#else + dev_err(&hw->pdev->dev, "Genesis chip detected but not configured\n"); + return -EOPNOTSUPP; +#endif + + case CHIP_ID_YUKON: + case CHIP_ID_YUKON_LITE: + case CHIP_ID_YUKON_LP: + if (hw->phy_type < SK_PHY_MARV_COPPER && pmd_type != 'S') + hw->copper = 1; + + hw->phy_addr = PHY_ADDR_MARV; + break; + + default: + dev_err(&hw->pdev->dev, "unsupported chip type 0x%x\n", + hw->chip_id); + return -EOPNOTSUPP; + } + + mac_cfg = skge_read8(hw, B2_MAC_CFG); + hw->ports = (mac_cfg & CFG_SNG_MAC) ? 1 : 2; + hw->chip_rev = (mac_cfg & CFG_CHIP_R_MSK) >> 4; + + /* read the adapters RAM size */ + t8 = skge_read8(hw, B2_E_0); + if (is_genesis(hw)) { + if (t8 == 3) { + /* special case: 4 x 64k x 36, offset = 0x80000 */ + hw->ram_size = 0x100000; + hw->ram_offset = 0x80000; + } else + hw->ram_size = t8 * 512; + } else if (t8 == 0) + hw->ram_size = 0x20000; + else + hw->ram_size = t8 * 4096; + + hw->intr_mask = IS_HW_ERR; + + /* Use PHY IRQ for all but fiber based Genesis board */ + if (!(is_genesis(hw) && hw->phy_type == SK_PHY_XMAC)) + hw->intr_mask |= IS_EXT_REG; + + if (is_genesis(hw)) + genesis_init(hw); + else { + /* switch power to VCC (WA for VAUX problem) */ + skge_write8(hw, B0_POWER_CTRL, + PC_VAUX_ENA | PC_VCC_ENA | PC_VAUX_OFF | PC_VCC_ON); + + /* avoid boards with stuck Hardware error bits */ + if ((skge_read32(hw, B0_ISRC) & IS_HW_ERR) && + (skge_read32(hw, B0_HWE_ISRC) & IS_IRQ_SENSOR)) { + dev_warn(&hw->pdev->dev, "stuck hardware sensor bit\n"); + hw->intr_mask &= ~IS_HW_ERR; + } + + /* Clear PHY COMA */ + skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON); + pci_read_config_dword(hw->pdev, PCI_DEV_REG1, ®); + reg &= ~PCI_PHY_COMA; + pci_write_config_dword(hw->pdev, PCI_DEV_REG1, reg); + skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); + + + for (i = 0; i < hw->ports; i++) { + skge_write16(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET); + skge_write16(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_CLR); + } + } + + /* turn off hardware timer (unused) */ + skge_write8(hw, B2_TI_CTRL, TIM_STOP); + skge_write8(hw, B2_TI_CTRL, TIM_CLR_IRQ); + skge_write8(hw, B0_LED, LED_STAT_ON); + + /* enable the Tx Arbiters */ + for (i = 0; i < hw->ports; i++) + skge_write8(hw, SK_REG(i, TXA_CTRL), TXA_ENA_ARB); + + /* Initialize ram interface */ + skge_write16(hw, B3_RI_CTRL, RI_RST_CLR); + + skge_write8(hw, B3_RI_WTO_R1, SK_RI_TO_53); + skge_write8(hw, B3_RI_WTO_XA1, SK_RI_TO_53); + skge_write8(hw, B3_RI_WTO_XS1, SK_RI_TO_53); + skge_write8(hw, B3_RI_RTO_R1, SK_RI_TO_53); + skge_write8(hw, B3_RI_RTO_XA1, SK_RI_TO_53); + skge_write8(hw, B3_RI_RTO_XS1, SK_RI_TO_53); + skge_write8(hw, B3_RI_WTO_R2, SK_RI_TO_53); + skge_write8(hw, B3_RI_WTO_XA2, SK_RI_TO_53); + skge_write8(hw, B3_RI_WTO_XS2, SK_RI_TO_53); + skge_write8(hw, B3_RI_RTO_R2, SK_RI_TO_53); + skge_write8(hw, B3_RI_RTO_XA2, SK_RI_TO_53); + skge_write8(hw, B3_RI_RTO_XS2, SK_RI_TO_53); + + skge_write32(hw, B0_HWE_IMSK, IS_ERR_MSK); + + /* Set interrupt moderation for Transmit only + * Receive interrupts avoided by NAPI + */ + skge_write32(hw, B2_IRQM_MSK, IS_XA1_F|IS_XA2_F); + skge_write32(hw, B2_IRQM_INI, skge_usecs2clk(hw, 100)); + skge_write32(hw, B2_IRQM_CTRL, TIM_START); + + /* Leave irq disabled until first port is brought up. */ + skge_write32(hw, B0_IMSK, 0); + + for (i = 0; i < hw->ports; i++) { + if (is_genesis(hw)) + genesis_reset(hw, i); + else + yukon_reset(hw, i); + } + + return 0; +} + + +#ifdef CONFIG_SKGE_DEBUG + +static struct dentry *skge_debug; + +static int skge_debug_show(struct seq_file *seq, void *v) +{ + struct net_device *dev = seq->private; + const struct skge_port *skge = netdev_priv(dev); + const struct skge_hw *hw = skge->hw; + const struct skge_element *e; + + if (!netif_running(dev)) + return -ENETDOWN; + + seq_printf(seq, "IRQ src=%x mask=%x\n", skge_read32(hw, B0_ISRC), + skge_read32(hw, B0_IMSK)); + + seq_printf(seq, "Tx Ring: (%d)\n", skge_avail(&skge->tx_ring)); + for (e = skge->tx_ring.to_clean; e != skge->tx_ring.to_use; e = e->next) { + const struct skge_tx_desc *t = e->desc; + seq_printf(seq, "%#x dma=%#x%08x %#x csum=%#x/%x/%x\n", + t->control, t->dma_hi, t->dma_lo, t->status, + t->csum_offs, t->csum_write, t->csum_start); + } + + seq_puts(seq, "\nRx Ring:\n"); + for (e = skge->rx_ring.to_clean; ; e = e->next) { + const struct skge_rx_desc *r = e->desc; + + if (r->control & BMU_OWN) + break; + + seq_printf(seq, "%#x dma=%#x%08x %#x %#x csum=%#x/%x\n", + r->control, r->dma_hi, r->dma_lo, r->status, + r->timestamp, r->csum1, r->csum1_start); + } + + return 0; +} +DEFINE_SHOW_ATTRIBUTE(skge_debug); + +/* + * Use network device events to create/remove/rename + * debugfs file entries + */ +static int skge_device_event(struct notifier_block *unused, + unsigned long event, void *ptr) +{ + struct net_device *dev = netdev_notifier_info_to_dev(ptr); + struct skge_port *skge; + + if (dev->netdev_ops->ndo_open != &skge_up || !skge_debug) + goto done; + + skge = netdev_priv(dev); + switch (event) { + case NETDEV_CHANGENAME: + if (skge->debugfs) + skge->debugfs = debugfs_rename(skge_debug, + skge->debugfs, + skge_debug, dev->name); + break; + + case NETDEV_GOING_DOWN: + debugfs_remove(skge->debugfs); + skge->debugfs = NULL; + break; + + case NETDEV_UP: + skge->debugfs = debugfs_create_file(dev->name, 0444, skge_debug, + dev, &skge_debug_fops); + break; + } + +done: + return NOTIFY_DONE; +} + +static struct notifier_block skge_notifier = { + .notifier_call = skge_device_event, +}; + + +static __init void skge_debug_init(void) +{ + skge_debug = debugfs_create_dir("skge", NULL); + + register_netdevice_notifier(&skge_notifier); +} + +static __exit void skge_debug_cleanup(void) +{ + if (skge_debug) { + unregister_netdevice_notifier(&skge_notifier); + debugfs_remove(skge_debug); + skge_debug = NULL; + } +} + +#else +#define skge_debug_init() +#define skge_debug_cleanup() +#endif + +static const struct net_device_ops skge_netdev_ops = { + .ndo_open = skge_up, + .ndo_stop = skge_down, + .ndo_start_xmit = skge_xmit_frame, + .ndo_eth_ioctl = skge_ioctl, + .ndo_get_stats = skge_get_stats, + .ndo_tx_timeout = skge_tx_timeout, + .ndo_change_mtu = skge_change_mtu, + .ndo_validate_addr = eth_validate_addr, + .ndo_set_rx_mode = skge_set_multicast, + .ndo_set_mac_address = skge_set_mac_address, +#ifdef CONFIG_NET_POLL_CONTROLLER + .ndo_poll_controller = skge_netpoll, +#endif +}; + + +/* Initialize network device */ +static struct net_device *skge_devinit(struct skge_hw *hw, int port, + int highmem) +{ + struct skge_port *skge; + struct net_device *dev = alloc_etherdev(sizeof(*skge)); + u8 addr[ETH_ALEN]; + + if (!dev) + return NULL; + + SET_NETDEV_DEV(dev, &hw->pdev->dev); + dev->netdev_ops = &skge_netdev_ops; + dev->ethtool_ops = &skge_ethtool_ops; + dev->watchdog_timeo = TX_WATCHDOG; + dev->irq = hw->pdev->irq; + + /* MTU range: 60 - 9000 */ + dev->min_mtu = ETH_ZLEN; + dev->max_mtu = ETH_JUMBO_MTU; + + if (highmem) + dev->features |= NETIF_F_HIGHDMA; + + skge = netdev_priv(dev); + netif_napi_add(dev, &skge->napi, skge_poll); + skge->netdev = dev; + skge->hw = hw; + skge->msg_enable = netif_msg_init(debug, default_msg); + + skge->tx_ring.count = DEFAULT_TX_RING_SIZE; + skge->rx_ring.count = DEFAULT_RX_RING_SIZE; + + /* Auto speed and flow control */ + skge->autoneg = AUTONEG_ENABLE; + skge->flow_control = FLOW_MODE_SYM_OR_REM; + skge->duplex = -1; + skge->speed = -1; + skge->advertising = skge_supported_modes(hw); + + if (device_can_wakeup(&hw->pdev->dev)) { + skge->wol = wol_supported(hw) & WAKE_MAGIC; + device_set_wakeup_enable(&hw->pdev->dev, skge->wol); + } + + hw->dev[port] = dev; + + skge->port = port; + + /* Only used for Genesis XMAC */ + if (is_genesis(hw)) + timer_setup(&skge->link_timer, xm_link_timer, 0); + else { + dev->hw_features = NETIF_F_IP_CSUM | NETIF_F_SG | + NETIF_F_RXCSUM; + dev->features |= dev->hw_features; + } + + /* read the mac address */ + memcpy_fromio(addr, hw->regs + B2_MAC_1 + port*8, ETH_ALEN); + eth_hw_addr_set(dev, addr); + + return dev; +} + +static void skge_show_addr(struct net_device *dev) +{ + const struct skge_port *skge = netdev_priv(dev); + + netif_info(skge, probe, skge->netdev, "addr %pM\n", dev->dev_addr); +} + +static int only_32bit_dma; + +static int skge_probe(struct pci_dev *pdev, const struct pci_device_id *ent) +{ + struct net_device *dev, *dev1; + struct skge_hw *hw; + int err, using_dac = 0; + + err = pci_enable_device(pdev); + if (err) { + dev_err(&pdev->dev, "cannot enable PCI device\n"); + goto err_out; + } + + err = pci_request_regions(pdev, DRV_NAME); + if (err) { + dev_err(&pdev->dev, "cannot obtain PCI resources\n"); + goto err_out_disable_pdev; + } + + pci_set_master(pdev); + + if (!only_32bit_dma && !dma_set_mask(&pdev->dev, DMA_BIT_MASK(64))) { + using_dac = 1; + err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64)); + } else if (!(err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32)))) { + using_dac = 0; + err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32)); + } + + if (err) { + dev_err(&pdev->dev, "no usable DMA configuration\n"); + goto err_out_free_regions; + } + +#ifdef __BIG_ENDIAN + /* byte swap descriptors in hardware */ + { + u32 reg; + + pci_read_config_dword(pdev, PCI_DEV_REG2, ®); + reg |= PCI_REV_DESC; + pci_write_config_dword(pdev, PCI_DEV_REG2, reg); + } +#endif + + err = -ENOMEM; + /* space for skge@pci:0000:04:00.0 */ + hw = kzalloc(sizeof(*hw) + strlen(DRV_NAME "@pci:") + + strlen(pci_name(pdev)) + 1, GFP_KERNEL); + if (!hw) + goto err_out_free_regions; + + sprintf(hw->irq_name, DRV_NAME "@pci:%s", pci_name(pdev)); + + hw->pdev = pdev; + spin_lock_init(&hw->hw_lock); + spin_lock_init(&hw->phy_lock); + tasklet_setup(&hw->phy_task, skge_extirq); + + hw->regs = ioremap(pci_resource_start(pdev, 0), 0x4000); + if (!hw->regs) { + dev_err(&pdev->dev, "cannot map device registers\n"); + goto err_out_free_hw; + } + + err = skge_reset(hw); + if (err) + goto err_out_iounmap; + + pr_info("%s addr 0x%llx irq %d chip %s rev %d\n", + DRV_VERSION, + (unsigned long long)pci_resource_start(pdev, 0), pdev->irq, + skge_board_name(hw), hw->chip_rev); + + dev = skge_devinit(hw, 0, using_dac); + if (!dev) { + err = -ENOMEM; + goto err_out_led_off; + } + + /* Some motherboards are broken and has zero in ROM. */ + if (!is_valid_ether_addr(dev->dev_addr)) + dev_warn(&pdev->dev, "bad (zero?) ethernet address in rom\n"); + + err = register_netdev(dev); + if (err) { + dev_err(&pdev->dev, "cannot register net device\n"); + goto err_out_free_netdev; + } + + skge_show_addr(dev); + + if (hw->ports > 1) { + dev1 = skge_devinit(hw, 1, using_dac); + if (!dev1) { + err = -ENOMEM; + goto err_out_unregister; + } + + err = register_netdev(dev1); + if (err) { + dev_err(&pdev->dev, "cannot register second net device\n"); + goto err_out_free_dev1; + } + + err = request_irq(pdev->irq, skge_intr, IRQF_SHARED, + hw->irq_name, hw); + if (err) { + dev_err(&pdev->dev, "cannot assign irq %d\n", + pdev->irq); + goto err_out_unregister_dev1; + } + + skge_show_addr(dev1); + } + pci_set_drvdata(pdev, hw); + + return 0; + +err_out_unregister_dev1: + unregister_netdev(dev1); +err_out_free_dev1: + free_netdev(dev1); +err_out_unregister: + unregister_netdev(dev); +err_out_free_netdev: + free_netdev(dev); +err_out_led_off: + skge_write16(hw, B0_LED, LED_STAT_OFF); +err_out_iounmap: + iounmap(hw->regs); +err_out_free_hw: + kfree(hw); +err_out_free_regions: + pci_release_regions(pdev); +err_out_disable_pdev: + pci_disable_device(pdev); +err_out: + return err; +} + +static void skge_remove(struct pci_dev *pdev) +{ + struct skge_hw *hw = pci_get_drvdata(pdev); + struct net_device *dev0, *dev1; + + if (!hw) + return; + + dev1 = hw->dev[1]; + if (dev1) + unregister_netdev(dev1); + dev0 = hw->dev[0]; + unregister_netdev(dev0); + + tasklet_kill(&hw->phy_task); + + spin_lock_irq(&hw->hw_lock); + hw->intr_mask = 0; + + if (hw->ports > 1) { + skge_write32(hw, B0_IMSK, 0); + skge_read32(hw, B0_IMSK); + } + spin_unlock_irq(&hw->hw_lock); + + skge_write16(hw, B0_LED, LED_STAT_OFF); + skge_write8(hw, B0_CTST, CS_RST_SET); + + if (hw->ports > 1) + free_irq(pdev->irq, hw); + pci_release_regions(pdev); + pci_disable_device(pdev); + if (dev1) + free_netdev(dev1); + free_netdev(dev0); + + iounmap(hw->regs); + kfree(hw); +} + +#ifdef CONFIG_PM_SLEEP +static int skge_suspend(struct device *dev) +{ + struct skge_hw *hw = dev_get_drvdata(dev); + int i; + + if (!hw) + return 0; + + for (i = 0; i < hw->ports; i++) { + struct net_device *dev = hw->dev[i]; + struct skge_port *skge = netdev_priv(dev); + + if (netif_running(dev)) + skge_down(dev); + + if (skge->wol) + skge_wol_init(skge); + } + + skge_write32(hw, B0_IMSK, 0); + + return 0; +} + +static int skge_resume(struct device *dev) +{ + struct skge_hw *hw = dev_get_drvdata(dev); + int i, err; + + if (!hw) + return 0; + + err = skge_reset(hw); + if (err) + goto out; + + for (i = 0; i < hw->ports; i++) { + struct net_device *dev = hw->dev[i]; + + if (netif_running(dev)) { + err = skge_up(dev); + + if (err) { + netdev_err(dev, "could not up: %d\n", err); + dev_close(dev); + goto out; + } + } + } +out: + return err; +} + +static SIMPLE_DEV_PM_OPS(skge_pm_ops, skge_suspend, skge_resume); +#define SKGE_PM_OPS (&skge_pm_ops) + +#else + +#define SKGE_PM_OPS NULL +#endif /* CONFIG_PM_SLEEP */ + +static void skge_shutdown(struct pci_dev *pdev) +{ + struct skge_hw *hw = pci_get_drvdata(pdev); + int i; + + if (!hw) + return; + + for (i = 0; i < hw->ports; i++) { + struct net_device *dev = hw->dev[i]; + struct skge_port *skge = netdev_priv(dev); + + if (skge->wol) + skge_wol_init(skge); + } + + pci_wake_from_d3(pdev, device_may_wakeup(&pdev->dev)); + pci_set_power_state(pdev, PCI_D3hot); +} + +static struct pci_driver skge_driver = { + .name = DRV_NAME, + .id_table = skge_id_table, + .probe = skge_probe, + .remove = skge_remove, + .shutdown = skge_shutdown, + .driver.pm = SKGE_PM_OPS, +}; + +static const struct dmi_system_id skge_32bit_dma_boards[] = { + { + .ident = "Gigabyte nForce boards", + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, "Gigabyte Technology Co"), + DMI_MATCH(DMI_BOARD_NAME, "nForce"), + }, + }, + { + .ident = "ASUS P5NSLI", + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, "ASUSTeK Computer INC."), + DMI_MATCH(DMI_BOARD_NAME, "P5NSLI") + }, + }, + { + .ident = "FUJITSU SIEMENS A8NE-FM", + .matches = { + DMI_MATCH(DMI_BOARD_VENDOR, "ASUSTek Computer INC."), + DMI_MATCH(DMI_BOARD_NAME, "A8NE-FM") + }, + }, + {} +}; + +static int __init skge_init_module(void) +{ + if (dmi_check_system(skge_32bit_dma_boards)) + only_32bit_dma = 1; + skge_debug_init(); + return pci_register_driver(&skge_driver); +} + +static void __exit skge_cleanup_module(void) +{ + pci_unregister_driver(&skge_driver); + skge_debug_cleanup(); +} + +module_init(skge_init_module); +module_exit(skge_cleanup_module); |