diff options
Diffstat (limited to 'drivers/net/ethernet/smsc/smc91x.h')
| -rw-r--r-- | drivers/net/ethernet/smsc/smc91x.h | 1107 |
1 files changed, 1107 insertions, 0 deletions
diff --git a/drivers/net/ethernet/smsc/smc91x.h b/drivers/net/ethernet/smsc/smc91x.h new file mode 100644 index 000000000..c521ea8f9 --- /dev/null +++ b/drivers/net/ethernet/smsc/smc91x.h @@ -0,0 +1,1107 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ +/*------------------------------------------------------------------------ + . smc91x.h - macros for SMSC's 91C9x/91C1xx single-chip Ethernet device. + . + . Copyright (C) 1996 by Erik Stahlman + . Copyright (C) 2001 Standard Microsystems Corporation + . Developed by Simple Network Magic Corporation + . Copyright (C) 2003 Monta Vista Software, Inc. + . Unified SMC91x driver by Nicolas Pitre + . + . + . Information contained in this file was obtained from the LAN91C111 + . manual from SMC. To get a copy, if you really want one, you can find + . information under www.smsc.com. + . + . Authors + . Erik Stahlman <erik@vt.edu> + . Daris A Nevil <dnevil@snmc.com> + . Nicolas Pitre <nico@fluxnic.net> + . + ---------------------------------------------------------------------------*/ +#ifndef _SMC91X_H_ +#define _SMC91X_H_ + +#include <linux/dmaengine.h> +#include <linux/smc91x.h> + +/* + * Any 16-bit access is performed with two 8-bit accesses if the hardware + * can't do it directly. Most registers are 16-bit so those are mandatory. + */ +#define SMC_outw_b(x, a, r) \ + do { \ + unsigned int __val16 = (x); \ + unsigned int __reg = (r); \ + SMC_outb(__val16, a, __reg); \ + SMC_outb(__val16 >> 8, a, __reg + (1 << SMC_IO_SHIFT)); \ + } while (0) + +#define SMC_inw_b(a, r) \ + ({ \ + unsigned int __val16; \ + unsigned int __reg = r; \ + __val16 = SMC_inb(a, __reg); \ + __val16 |= SMC_inb(a, __reg + (1 << SMC_IO_SHIFT)) << 8; \ + __val16; \ + }) + +/* + * Define your architecture specific bus configuration parameters here. + */ + +#if defined(CONFIG_ARM) + +#include <asm/mach-types.h> + +/* Now the bus width is specified in the platform data + * pretend here to support all I/O access types + */ +#define SMC_CAN_USE_8BIT 1 +#define SMC_CAN_USE_16BIT 1 +#define SMC_CAN_USE_32BIT 1 +#define SMC_NOWAIT 1 + +#define SMC_IO_SHIFT (lp->io_shift) + +#define SMC_inb(a, r) readb((a) + (r)) +#define SMC_inw(a, r) \ + ({ \ + unsigned int __smc_r = r; \ + SMC_16BIT(lp) ? readw((a) + __smc_r) : \ + SMC_8BIT(lp) ? SMC_inw_b(a, __smc_r) : \ + ({ BUG(); 0; }); \ + }) + +#define SMC_inl(a, r) readl((a) + (r)) +#define SMC_outb(v, a, r) writeb(v, (a) + (r)) +#define SMC_outw(lp, v, a, r) \ + do { \ + unsigned int __v = v, __smc_r = r; \ + if (SMC_16BIT(lp)) \ + __SMC_outw(lp, __v, a, __smc_r); \ + else if (SMC_8BIT(lp)) \ + SMC_outw_b(__v, a, __smc_r); \ + else \ + BUG(); \ + } while (0) + +#define SMC_outl(v, a, r) writel(v, (a) + (r)) +#define SMC_insb(a, r, p, l) readsb((a) + (r), p, l) +#define SMC_outsb(a, r, p, l) writesb((a) + (r), p, l) +#define SMC_insw(a, r, p, l) readsw((a) + (r), p, l) +#define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l) +#define SMC_insl(a, r, p, l) readsl((a) + (r), p, l) +#define SMC_outsl(a, r, p, l) writesl((a) + (r), p, l) +#define SMC_IRQ_FLAGS (-1) /* from resource */ + +/* We actually can't write halfwords properly if not word aligned */ +static inline void _SMC_outw_align4(u16 val, void __iomem *ioaddr, int reg, + bool use_align4_workaround) +{ + if (use_align4_workaround) { + unsigned int v = val << 16; + v |= readl(ioaddr + (reg & ~2)) & 0xffff; + writel(v, ioaddr + (reg & ~2)); + } else { + writew(val, ioaddr + reg); + } +} + +#define __SMC_outw(lp, v, a, r) \ + _SMC_outw_align4((v), (a), (r), \ + IS_BUILTIN(CONFIG_ARCH_PXA) && ((r) & 2) && \ + (lp)->cfg.pxa_u16_align4) + + +#elif defined(CONFIG_SH_SH4202_MICRODEV) + +#define SMC_CAN_USE_8BIT 0 +#define SMC_CAN_USE_16BIT 1 +#define SMC_CAN_USE_32BIT 0 + +#define SMC_inb(a, r) inb((a) + (r) - 0xa0000000) +#define SMC_inw(a, r) inw((a) + (r) - 0xa0000000) +#define SMC_inl(a, r) inl((a) + (r) - 0xa0000000) +#define SMC_outb(v, a, r) outb(v, (a) + (r) - 0xa0000000) +#define SMC_outw(lp, v, a, r) outw(v, (a) + (r) - 0xa0000000) +#define SMC_outl(v, a, r) outl(v, (a) + (r) - 0xa0000000) +#define SMC_insl(a, r, p, l) insl((a) + (r) - 0xa0000000, p, l) +#define SMC_outsl(a, r, p, l) outsl((a) + (r) - 0xa0000000, p, l) +#define SMC_insw(a, r, p, l) insw((a) + (r) - 0xa0000000, p, l) +#define SMC_outsw(a, r, p, l) outsw((a) + (r) - 0xa0000000, p, l) + +#define SMC_IRQ_FLAGS (0) + +#elif defined(CONFIG_ATARI) + +#define SMC_CAN_USE_8BIT 1 +#define SMC_CAN_USE_16BIT 1 +#define SMC_CAN_USE_32BIT 1 +#define SMC_NOWAIT 1 + +#define SMC_inb(a, r) readb((a) + (r)) +#define SMC_inw(a, r) readw((a) + (r)) +#define SMC_inl(a, r) readl((a) + (r)) +#define SMC_outb(v, a, r) writeb(v, (a) + (r)) +#define SMC_outw(lp, v, a, r) writew(v, (a) + (r)) +#define SMC_outl(v, a, r) writel(v, (a) + (r)) +#define SMC_insw(a, r, p, l) readsw((a) + (r), p, l) +#define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l) +#define SMC_insl(a, r, p, l) readsl((a) + (r), p, l) +#define SMC_outsl(a, r, p, l) writesl((a) + (r), p, l) + +#define RPC_LSA_DEFAULT RPC_LED_100_10 +#define RPC_LSB_DEFAULT RPC_LED_TX_RX + +#elif defined(CONFIG_COLDFIRE) + +#define SMC_CAN_USE_8BIT 0 +#define SMC_CAN_USE_16BIT 1 +#define SMC_CAN_USE_32BIT 0 +#define SMC_NOWAIT 1 + +static inline void mcf_insw(void *a, unsigned char *p, int l) +{ + u16 *wp = (u16 *) p; + while (l-- > 0) + *wp++ = readw(a); +} + +static inline void mcf_outsw(void *a, unsigned char *p, int l) +{ + u16 *wp = (u16 *) p; + while (l-- > 0) + writew(*wp++, a); +} + +#define SMC_inw(a, r) _swapw(readw((a) + (r))) +#define SMC_outw(lp, v, a, r) writew(_swapw(v), (a) + (r)) +#define SMC_insw(a, r, p, l) mcf_insw(a + r, p, l) +#define SMC_outsw(a, r, p, l) mcf_outsw(a + r, p, l) + +#define SMC_IRQ_FLAGS 0 + +#else + +/* + * Default configuration + */ + +#define SMC_CAN_USE_8BIT 1 +#define SMC_CAN_USE_16BIT 1 +#define SMC_CAN_USE_32BIT 1 +#define SMC_NOWAIT 1 + +#define SMC_IO_SHIFT (lp->io_shift) + +#define SMC_inb(a, r) ioread8((a) + (r)) +#define SMC_inw(a, r) ioread16((a) + (r)) +#define SMC_inl(a, r) ioread32((a) + (r)) +#define SMC_outb(v, a, r) iowrite8(v, (a) + (r)) +#define SMC_outw(lp, v, a, r) iowrite16(v, (a) + (r)) +#define SMC_outl(v, a, r) iowrite32(v, (a) + (r)) +#define SMC_insw(a, r, p, l) ioread16_rep((a) + (r), p, l) +#define SMC_outsw(a, r, p, l) iowrite16_rep((a) + (r), p, l) +#define SMC_insl(a, r, p, l) ioread32_rep((a) + (r), p, l) +#define SMC_outsl(a, r, p, l) iowrite32_rep((a) + (r), p, l) + +#define RPC_LSA_DEFAULT RPC_LED_100_10 +#define RPC_LSB_DEFAULT RPC_LED_TX_RX + +#endif + + +/* store this information for the driver.. */ +struct smc_local { + /* + * If I have to wait until memory is available to send a + * packet, I will store the skbuff here, until I get the + * desired memory. Then, I'll send it out and free it. + */ + struct sk_buff *pending_tx_skb; + struct tasklet_struct tx_task; + + struct gpio_desc *power_gpio; + struct gpio_desc *reset_gpio; + + /* version/revision of the SMC91x chip */ + int version; + + /* Contains the current active transmission mode */ + int tcr_cur_mode; + + /* Contains the current active receive mode */ + int rcr_cur_mode; + + /* Contains the current active receive/phy mode */ + int rpc_cur_mode; + int ctl_rfduplx; + int ctl_rspeed; + + u32 msg_enable; + u32 phy_type; + struct mii_if_info mii; + + /* work queue */ + struct work_struct phy_configure; + struct net_device *dev; + int work_pending; + + spinlock_t lock; + +#ifdef CONFIG_ARCH_PXA + /* DMA needs the physical address of the chip */ + u_long physaddr; + struct device *device; +#endif + struct dma_chan *dma_chan; + void __iomem *base; + void __iomem *datacs; + + /* the low address lines on some platforms aren't connected... */ + int io_shift; + /* on some platforms a u16 write must be 4-bytes aligned */ + bool half_word_align4; + + struct smc91x_platdata cfg; +}; + +#define SMC_8BIT(p) ((p)->cfg.flags & SMC91X_USE_8BIT) +#define SMC_16BIT(p) ((p)->cfg.flags & SMC91X_USE_16BIT) +#define SMC_32BIT(p) ((p)->cfg.flags & SMC91X_USE_32BIT) + +#ifdef CONFIG_ARCH_PXA +/* + * Let's use the DMA engine on the XScale PXA2xx for RX packets. This is + * always happening in irq context so no need to worry about races. TX is + * different and probably not worth it for that reason, and not as critical + * as RX which can overrun memory and lose packets. + */ +#include <linux/dma-mapping.h> + +#ifdef SMC_insl +#undef SMC_insl +#define SMC_insl(a, r, p, l) \ + smc_pxa_dma_insl(a, lp, r, dev->dma, p, l) +static inline void +smc_pxa_dma_inpump(struct smc_local *lp, u_char *buf, int len) +{ + dma_addr_t dmabuf; + struct dma_async_tx_descriptor *tx; + dma_cookie_t cookie; + enum dma_status status; + struct dma_tx_state state; + + dmabuf = dma_map_single(lp->device, buf, len, DMA_FROM_DEVICE); + tx = dmaengine_prep_slave_single(lp->dma_chan, dmabuf, len, + DMA_DEV_TO_MEM, 0); + if (tx) { + cookie = dmaengine_submit(tx); + dma_async_issue_pending(lp->dma_chan); + do { + status = dmaengine_tx_status(lp->dma_chan, cookie, + &state); + cpu_relax(); + } while (status != DMA_COMPLETE && status != DMA_ERROR && + state.residue); + dmaengine_terminate_all(lp->dma_chan); + } + dma_unmap_single(lp->device, dmabuf, len, DMA_FROM_DEVICE); +} + +static inline void +smc_pxa_dma_insl(void __iomem *ioaddr, struct smc_local *lp, int reg, int dma, + u_char *buf, int len) +{ + struct dma_slave_config config; + int ret; + + /* fallback if no DMA available */ + if (!lp->dma_chan) { + readsl(ioaddr + reg, buf, len); + return; + } + + /* 64 bit alignment is required for memory to memory DMA */ + if ((long)buf & 4) { + *((u32 *)buf) = SMC_inl(ioaddr, reg); + buf += 4; + len--; + } + + memset(&config, 0, sizeof(config)); + config.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + config.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES; + config.src_addr = lp->physaddr + reg; + config.dst_addr = lp->physaddr + reg; + config.src_maxburst = 32; + config.dst_maxburst = 32; + ret = dmaengine_slave_config(lp->dma_chan, &config); + if (ret) { + dev_err(lp->device, "dma channel configuration failed: %d\n", + ret); + return; + } + + len *= 4; + smc_pxa_dma_inpump(lp, buf, len); +} +#endif + +#ifdef SMC_insw +#undef SMC_insw +#define SMC_insw(a, r, p, l) \ + smc_pxa_dma_insw(a, lp, r, dev->dma, p, l) +static inline void +smc_pxa_dma_insw(void __iomem *ioaddr, struct smc_local *lp, int reg, int dma, + u_char *buf, int len) +{ + struct dma_slave_config config; + int ret; + + /* fallback if no DMA available */ + if (!lp->dma_chan) { + readsw(ioaddr + reg, buf, len); + return; + } + + /* 64 bit alignment is required for memory to memory DMA */ + while ((long)buf & 6) { + *((u16 *)buf) = SMC_inw(ioaddr, reg); + buf += 2; + len--; + } + + memset(&config, 0, sizeof(config)); + config.src_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES; + config.dst_addr_width = DMA_SLAVE_BUSWIDTH_2_BYTES; + config.src_addr = lp->physaddr + reg; + config.dst_addr = lp->physaddr + reg; + config.src_maxburst = 32; + config.dst_maxburst = 32; + ret = dmaengine_slave_config(lp->dma_chan, &config); + if (ret) { + dev_err(lp->device, "dma channel configuration failed: %d\n", + ret); + return; + } + + len *= 2; + smc_pxa_dma_inpump(lp, buf, len); +} +#endif + +#endif /* CONFIG_ARCH_PXA */ + + +/* + * Everything a particular hardware setup needs should have been defined + * at this point. Add stubs for the undefined cases, mainly to avoid + * compilation warnings since they'll be optimized away, or to prevent buggy + * use of them. + */ + +#if ! SMC_CAN_USE_32BIT +#define SMC_inl(ioaddr, reg) ({ BUG(); 0; }) +#define SMC_outl(x, ioaddr, reg) BUG() +#define SMC_insl(a, r, p, l) BUG() +#define SMC_outsl(a, r, p, l) BUG() +#endif + +#if !defined(SMC_insl) || !defined(SMC_outsl) +#define SMC_insl(a, r, p, l) BUG() +#define SMC_outsl(a, r, p, l) BUG() +#endif + +#if ! SMC_CAN_USE_16BIT + +#define SMC_outw(lp, x, ioaddr, reg) SMC_outw_b(x, ioaddr, reg) +#define SMC_inw(ioaddr, reg) SMC_inw_b(ioaddr, reg) +#define SMC_insw(a, r, p, l) BUG() +#define SMC_outsw(a, r, p, l) BUG() + +#endif + +#if !defined(SMC_insw) || !defined(SMC_outsw) +#define SMC_insw(a, r, p, l) BUG() +#define SMC_outsw(a, r, p, l) BUG() +#endif + +#if ! SMC_CAN_USE_8BIT +#undef SMC_inb +#define SMC_inb(ioaddr, reg) ({ BUG(); 0; }) +#undef SMC_outb +#define SMC_outb(x, ioaddr, reg) BUG() +#define SMC_insb(a, r, p, l) BUG() +#define SMC_outsb(a, r, p, l) BUG() +#endif + +#if !defined(SMC_insb) || !defined(SMC_outsb) +#define SMC_insb(a, r, p, l) BUG() +#define SMC_outsb(a, r, p, l) BUG() +#endif + +#ifndef SMC_CAN_USE_DATACS +#define SMC_CAN_USE_DATACS 0 +#endif + +#ifndef SMC_IO_SHIFT +#define SMC_IO_SHIFT 0 +#endif + +#ifndef SMC_IRQ_FLAGS +#define SMC_IRQ_FLAGS IRQF_TRIGGER_RISING +#endif + +#ifndef SMC_INTERRUPT_PREAMBLE +#define SMC_INTERRUPT_PREAMBLE +#endif + + +/* Because of bank switching, the LAN91x uses only 16 I/O ports */ +#define SMC_IO_EXTENT (16 << SMC_IO_SHIFT) +#define SMC_DATA_EXTENT (4) + +/* + . Bank Select Register: + . + . yyyy yyyy 0000 00xx + . xx = bank number + . yyyy yyyy = 0x33, for identification purposes. +*/ +#define BANK_SELECT (14 << SMC_IO_SHIFT) + + +// Transmit Control Register +/* BANK 0 */ +#define TCR_REG(lp) SMC_REG(lp, 0x0000, 0) +#define TCR_ENABLE 0x0001 // When 1 we can transmit +#define TCR_LOOP 0x0002 // Controls output pin LBK +#define TCR_FORCOL 0x0004 // When 1 will force a collision +#define TCR_PAD_EN 0x0080 // When 1 will pad tx frames < 64 bytes w/0 +#define TCR_NOCRC 0x0100 // When 1 will not append CRC to tx frames +#define TCR_MON_CSN 0x0400 // When 1 tx monitors carrier +#define TCR_FDUPLX 0x0800 // When 1 enables full duplex operation +#define TCR_STP_SQET 0x1000 // When 1 stops tx if Signal Quality Error +#define TCR_EPH_LOOP 0x2000 // When 1 enables EPH block loopback +#define TCR_SWFDUP 0x8000 // When 1 enables Switched Full Duplex mode + +#define TCR_CLEAR 0 /* do NOTHING */ +/* the default settings for the TCR register : */ +#define TCR_DEFAULT (TCR_ENABLE | TCR_PAD_EN) + + +// EPH Status Register +/* BANK 0 */ +#define EPH_STATUS_REG(lp) SMC_REG(lp, 0x0002, 0) +#define ES_TX_SUC 0x0001 // Last TX was successful +#define ES_SNGL_COL 0x0002 // Single collision detected for last tx +#define ES_MUL_COL 0x0004 // Multiple collisions detected for last tx +#define ES_LTX_MULT 0x0008 // Last tx was a multicast +#define ES_16COL 0x0010 // 16 Collisions Reached +#define ES_SQET 0x0020 // Signal Quality Error Test +#define ES_LTXBRD 0x0040 // Last tx was a broadcast +#define ES_TXDEFR 0x0080 // Transmit Deferred +#define ES_LATCOL 0x0200 // Late collision detected on last tx +#define ES_LOSTCARR 0x0400 // Lost Carrier Sense +#define ES_EXC_DEF 0x0800 // Excessive Deferral +#define ES_CTR_ROL 0x1000 // Counter Roll Over indication +#define ES_LINK_OK 0x4000 // Driven by inverted value of nLNK pin +#define ES_TXUNRN 0x8000 // Tx Underrun + + +// Receive Control Register +/* BANK 0 */ +#define RCR_REG(lp) SMC_REG(lp, 0x0004, 0) +#define RCR_RX_ABORT 0x0001 // Set if a rx frame was aborted +#define RCR_PRMS 0x0002 // Enable promiscuous mode +#define RCR_ALMUL 0x0004 // When set accepts all multicast frames +#define RCR_RXEN 0x0100 // IFF this is set, we can receive packets +#define RCR_STRIP_CRC 0x0200 // When set strips CRC from rx packets +#define RCR_ABORT_ENB 0x0200 // When set will abort rx on collision +#define RCR_FILT_CAR 0x0400 // When set filters leading 12 bit s of carrier +#define RCR_SOFTRST 0x8000 // resets the chip + +/* the normal settings for the RCR register : */ +#define RCR_DEFAULT (RCR_STRIP_CRC | RCR_RXEN) +#define RCR_CLEAR 0x0 // set it to a base state + + +// Counter Register +/* BANK 0 */ +#define COUNTER_REG(lp) SMC_REG(lp, 0x0006, 0) + + +// Memory Information Register +/* BANK 0 */ +#define MIR_REG(lp) SMC_REG(lp, 0x0008, 0) + + +// Receive/Phy Control Register +/* BANK 0 */ +#define RPC_REG(lp) SMC_REG(lp, 0x000A, 0) +#define RPC_SPEED 0x2000 // When 1 PHY is in 100Mbps mode. +#define RPC_DPLX 0x1000 // When 1 PHY is in Full-Duplex Mode +#define RPC_ANEG 0x0800 // When 1 PHY is in Auto-Negotiate Mode +#define RPC_LSXA_SHFT 5 // Bits to shift LS2A,LS1A,LS0A to lsb +#define RPC_LSXB_SHFT 2 // Bits to get LS2B,LS1B,LS0B to lsb + +#ifndef RPC_LSA_DEFAULT +#define RPC_LSA_DEFAULT RPC_LED_100 +#endif +#ifndef RPC_LSB_DEFAULT +#define RPC_LSB_DEFAULT RPC_LED_FD +#endif + +#define RPC_DEFAULT (RPC_ANEG | RPC_SPEED | RPC_DPLX) + + +/* Bank 0 0x0C is reserved */ + +// Bank Select Register +/* All Banks */ +#define BSR_REG 0x000E + + +// Configuration Reg +/* BANK 1 */ +#define CONFIG_REG(lp) SMC_REG(lp, 0x0000, 1) +#define CONFIG_EXT_PHY 0x0200 // 1=external MII, 0=internal Phy +#define CONFIG_GPCNTRL 0x0400 // Inverse value drives pin nCNTRL +#define CONFIG_NO_WAIT 0x1000 // When 1 no extra wait states on ISA bus +#define CONFIG_EPH_POWER_EN 0x8000 // When 0 EPH is placed into low power mode. + +// Default is powered-up, Internal Phy, Wait States, and pin nCNTRL=low +#define CONFIG_DEFAULT (CONFIG_EPH_POWER_EN) + + +// Base Address Register +/* BANK 1 */ +#define BASE_REG(lp) SMC_REG(lp, 0x0002, 1) + + +// Individual Address Registers +/* BANK 1 */ +#define ADDR0_REG(lp) SMC_REG(lp, 0x0004, 1) +#define ADDR1_REG(lp) SMC_REG(lp, 0x0006, 1) +#define ADDR2_REG(lp) SMC_REG(lp, 0x0008, 1) + + +// General Purpose Register +/* BANK 1 */ +#define GP_REG(lp) SMC_REG(lp, 0x000A, 1) + + +// Control Register +/* BANK 1 */ +#define CTL_REG(lp) SMC_REG(lp, 0x000C, 1) +#define CTL_RCV_BAD 0x4000 // When 1 bad CRC packets are received +#define CTL_AUTO_RELEASE 0x0800 // When 1 tx pages are released automatically +#define CTL_LE_ENABLE 0x0080 // When 1 enables Link Error interrupt +#define CTL_CR_ENABLE 0x0040 // When 1 enables Counter Rollover interrupt +#define CTL_TE_ENABLE 0x0020 // When 1 enables Transmit Error interrupt +#define CTL_EEPROM_SELECT 0x0004 // Controls EEPROM reload & store +#define CTL_RELOAD 0x0002 // When set reads EEPROM into registers +#define CTL_STORE 0x0001 // When set stores registers into EEPROM + + +// MMU Command Register +/* BANK 2 */ +#define MMU_CMD_REG(lp) SMC_REG(lp, 0x0000, 2) +#define MC_BUSY 1 // When 1 the last release has not completed +#define MC_NOP (0<<5) // No Op +#define MC_ALLOC (1<<5) // OR with number of 256 byte packets +#define MC_RESET (2<<5) // Reset MMU to initial state +#define MC_REMOVE (3<<5) // Remove the current rx packet +#define MC_RELEASE (4<<5) // Remove and release the current rx packet +#define MC_FREEPKT (5<<5) // Release packet in PNR register +#define MC_ENQUEUE (6<<5) // Enqueue the packet for transmit +#define MC_RSTTXFIFO (7<<5) // Reset the TX FIFOs + + +// Packet Number Register +/* BANK 2 */ +#define PN_REG(lp) SMC_REG(lp, 0x0002, 2) + + +// Allocation Result Register +/* BANK 2 */ +#define AR_REG(lp) SMC_REG(lp, 0x0003, 2) +#define AR_FAILED 0x80 // Alocation Failed + + +// TX FIFO Ports Register +/* BANK 2 */ +#define TXFIFO_REG(lp) SMC_REG(lp, 0x0004, 2) +#define TXFIFO_TEMPTY 0x80 // TX FIFO Empty + +// RX FIFO Ports Register +/* BANK 2 */ +#define RXFIFO_REG(lp) SMC_REG(lp, 0x0005, 2) +#define RXFIFO_REMPTY 0x80 // RX FIFO Empty + +#define FIFO_REG(lp) SMC_REG(lp, 0x0004, 2) + +// Pointer Register +/* BANK 2 */ +#define PTR_REG(lp) SMC_REG(lp, 0x0006, 2) +#define PTR_RCV 0x8000 // 1=Receive area, 0=Transmit area +#define PTR_AUTOINC 0x4000 // Auto increment the pointer on each access +#define PTR_READ 0x2000 // When 1 the operation is a read + + +// Data Register +/* BANK 2 */ +#define DATA_REG(lp) SMC_REG(lp, 0x0008, 2) + + +// Interrupt Status/Acknowledge Register +/* BANK 2 */ +#define INT_REG(lp) SMC_REG(lp, 0x000C, 2) + + +// Interrupt Mask Register +/* BANK 2 */ +#define IM_REG(lp) SMC_REG(lp, 0x000D, 2) +#define IM_MDINT 0x80 // PHY MI Register 18 Interrupt +#define IM_ERCV_INT 0x40 // Early Receive Interrupt +#define IM_EPH_INT 0x20 // Set by Ethernet Protocol Handler section +#define IM_RX_OVRN_INT 0x10 // Set by Receiver Overruns +#define IM_ALLOC_INT 0x08 // Set when allocation request is completed +#define IM_TX_EMPTY_INT 0x04 // Set if the TX FIFO goes empty +#define IM_TX_INT 0x02 // Transmit Interrupt +#define IM_RCV_INT 0x01 // Receive Interrupt + + +// Multicast Table Registers +/* BANK 3 */ +#define MCAST_REG1(lp) SMC_REG(lp, 0x0000, 3) +#define MCAST_REG2(lp) SMC_REG(lp, 0x0002, 3) +#define MCAST_REG3(lp) SMC_REG(lp, 0x0004, 3) +#define MCAST_REG4(lp) SMC_REG(lp, 0x0006, 3) + + +// Management Interface Register (MII) +/* BANK 3 */ +#define MII_REG(lp) SMC_REG(lp, 0x0008, 3) +#define MII_MSK_CRS100 0x4000 // Disables CRS100 detection during tx half dup +#define MII_MDOE 0x0008 // MII Output Enable +#define MII_MCLK 0x0004 // MII Clock, pin MDCLK +#define MII_MDI 0x0002 // MII Input, pin MDI +#define MII_MDO 0x0001 // MII Output, pin MDO + + +// Revision Register +/* BANK 3 */ +/* ( hi: chip id low: rev # ) */ +#define REV_REG(lp) SMC_REG(lp, 0x000A, 3) + + +// Early RCV Register +/* BANK 3 */ +/* this is NOT on SMC9192 */ +#define ERCV_REG(lp) SMC_REG(lp, 0x000C, 3) +#define ERCV_RCV_DISCRD 0x0080 // When 1 discards a packet being received +#define ERCV_THRESHOLD 0x001F // ERCV Threshold Mask + + +// External Register +/* BANK 7 */ +#define EXT_REG(lp) SMC_REG(lp, 0x0000, 7) + + +#define CHIP_9192 3 +#define CHIP_9194 4 +#define CHIP_9195 5 +#define CHIP_9196 6 +#define CHIP_91100 7 +#define CHIP_91100FD 8 +#define CHIP_91111FD 9 + +static const char * chip_ids[ 16 ] = { + NULL, NULL, NULL, + /* 3 */ "SMC91C90/91C92", + /* 4 */ "SMC91C94", + /* 5 */ "SMC91C95", + /* 6 */ "SMC91C96", + /* 7 */ "SMC91C100", + /* 8 */ "SMC91C100FD", + /* 9 */ "SMC91C11xFD", + NULL, NULL, NULL, + NULL, NULL, NULL}; + + +/* + . Receive status bits +*/ +#define RS_ALGNERR 0x8000 +#define RS_BRODCAST 0x4000 +#define RS_BADCRC 0x2000 +#define RS_ODDFRAME 0x1000 +#define RS_TOOLONG 0x0800 +#define RS_TOOSHORT 0x0400 +#define RS_MULTICAST 0x0001 +#define RS_ERRORS (RS_ALGNERR | RS_BADCRC | RS_TOOLONG | RS_TOOSHORT) + + +/* + * PHY IDs + * LAN83C183 == LAN91C111 Internal PHY + */ +#define PHY_LAN83C183 0x0016f840 +#define PHY_LAN83C180 0x02821c50 + +/* + * PHY Register Addresses (LAN91C111 Internal PHY) + * + * Generic PHY registers can be found in <linux/mii.h> + * + * These phy registers are specific to our on-board phy. + */ + +// PHY Configuration Register 1 +#define PHY_CFG1_REG 0x10 +#define PHY_CFG1_LNKDIS 0x8000 // 1=Rx Link Detect Function disabled +#define PHY_CFG1_XMTDIS 0x4000 // 1=TP Transmitter Disabled +#define PHY_CFG1_XMTPDN 0x2000 // 1=TP Transmitter Powered Down +#define PHY_CFG1_BYPSCR 0x0400 // 1=Bypass scrambler/descrambler +#define PHY_CFG1_UNSCDS 0x0200 // 1=Unscramble Idle Reception Disable +#define PHY_CFG1_EQLZR 0x0100 // 1=Rx Equalizer Disabled +#define PHY_CFG1_CABLE 0x0080 // 1=STP(150ohm), 0=UTP(100ohm) +#define PHY_CFG1_RLVL0 0x0040 // 1=Rx Squelch level reduced by 4.5db +#define PHY_CFG1_TLVL_SHIFT 2 // Transmit Output Level Adjust +#define PHY_CFG1_TLVL_MASK 0x003C +#define PHY_CFG1_TRF_MASK 0x0003 // Transmitter Rise/Fall time + + +// PHY Configuration Register 2 +#define PHY_CFG2_REG 0x11 +#define PHY_CFG2_APOLDIS 0x0020 // 1=Auto Polarity Correction disabled +#define PHY_CFG2_JABDIS 0x0010 // 1=Jabber disabled +#define PHY_CFG2_MREG 0x0008 // 1=Multiple register access (MII mgt) +#define PHY_CFG2_INTMDIO 0x0004 // 1=Interrupt signaled with MDIO pulseo + +// PHY Status Output (and Interrupt status) Register +#define PHY_INT_REG 0x12 // Status Output (Interrupt Status) +#define PHY_INT_INT 0x8000 // 1=bits have changed since last read +#define PHY_INT_LNKFAIL 0x4000 // 1=Link Not detected +#define PHY_INT_LOSSSYNC 0x2000 // 1=Descrambler has lost sync +#define PHY_INT_CWRD 0x1000 // 1=Invalid 4B5B code detected on rx +#define PHY_INT_SSD 0x0800 // 1=No Start Of Stream detected on rx +#define PHY_INT_ESD 0x0400 // 1=No End Of Stream detected on rx +#define PHY_INT_RPOL 0x0200 // 1=Reverse Polarity detected +#define PHY_INT_JAB 0x0100 // 1=Jabber detected +#define PHY_INT_SPDDET 0x0080 // 1=100Base-TX mode, 0=10Base-T mode +#define PHY_INT_DPLXDET 0x0040 // 1=Device in Full Duplex + +// PHY Interrupt/Status Mask Register +#define PHY_MASK_REG 0x13 // Interrupt Mask +// Uses the same bit definitions as PHY_INT_REG + + +/* + * SMC91C96 ethernet config and status registers. + * These are in the "attribute" space. + */ +#define ECOR 0x8000 +#define ECOR_RESET 0x80 +#define ECOR_LEVEL_IRQ 0x40 +#define ECOR_WR_ATTRIB 0x04 +#define ECOR_ENABLE 0x01 + +#define ECSR 0x8002 +#define ECSR_IOIS8 0x20 +#define ECSR_PWRDWN 0x04 +#define ECSR_INT 0x02 + +#define ATTRIB_SIZE ((64*1024) << SMC_IO_SHIFT) + + +/* + * Macros to abstract register access according to the data bus + * capabilities. Please use those and not the in/out primitives. + * Note: the following macros do *not* select the bank -- this must + * be done separately as needed in the main code. The SMC_REG() macro + * only uses the bank argument for debugging purposes (when enabled). + * + * Note: despite inline functions being safer, everything leading to this + * should preferably be macros to let BUG() display the line number in + * the core source code since we're interested in the top call site + * not in any inline function location. + */ + +#if SMC_DEBUG > 0 +#define SMC_REG(lp, reg, bank) \ + ({ \ + int __b = SMC_CURRENT_BANK(lp); \ + if (unlikely((__b & ~0xf0) != (0x3300 | bank))) { \ + pr_err("%s: bank reg screwed (0x%04x)\n", \ + CARDNAME, __b); \ + BUG(); \ + } \ + reg<<SMC_IO_SHIFT; \ + }) +#else +#define SMC_REG(lp, reg, bank) (reg<<SMC_IO_SHIFT) +#endif + +/* + * Hack Alert: Some setups just can't write 8 or 16 bits reliably when not + * aligned to a 32 bit boundary. I tell you that does exist! + * Fortunately the affected register accesses can be easily worked around + * since we can write zeroes to the preceding 16 bits without adverse + * effects and use a 32-bit access. + * + * Enforce it on any 32-bit capable setup for now. + */ +#define SMC_MUST_ALIGN_WRITE(lp) SMC_32BIT(lp) + +#define SMC_GET_PN(lp) \ + (SMC_8BIT(lp) ? (SMC_inb(ioaddr, PN_REG(lp))) \ + : (SMC_inw(ioaddr, PN_REG(lp)) & 0xFF)) + +#define SMC_SET_PN(lp, x) \ + do { \ + if (SMC_MUST_ALIGN_WRITE(lp)) \ + SMC_outl((x)<<16, ioaddr, SMC_REG(lp, 0, 2)); \ + else if (SMC_8BIT(lp)) \ + SMC_outb(x, ioaddr, PN_REG(lp)); \ + else \ + SMC_outw(lp, x, ioaddr, PN_REG(lp)); \ + } while (0) + +#define SMC_GET_AR(lp) \ + (SMC_8BIT(lp) ? (SMC_inb(ioaddr, AR_REG(lp))) \ + : (SMC_inw(ioaddr, PN_REG(lp)) >> 8)) + +#define SMC_GET_TXFIFO(lp) \ + (SMC_8BIT(lp) ? (SMC_inb(ioaddr, TXFIFO_REG(lp))) \ + : (SMC_inw(ioaddr, TXFIFO_REG(lp)) & 0xFF)) + +#define SMC_GET_RXFIFO(lp) \ + (SMC_8BIT(lp) ? (SMC_inb(ioaddr, RXFIFO_REG(lp))) \ + : (SMC_inw(ioaddr, TXFIFO_REG(lp)) >> 8)) + +#define SMC_GET_INT(lp) \ + (SMC_8BIT(lp) ? (SMC_inb(ioaddr, INT_REG(lp))) \ + : (SMC_inw(ioaddr, INT_REG(lp)) & 0xFF)) + +#define SMC_ACK_INT(lp, x) \ + do { \ + if (SMC_8BIT(lp)) \ + SMC_outb(x, ioaddr, INT_REG(lp)); \ + else { \ + unsigned long __flags; \ + int __mask; \ + local_irq_save(__flags); \ + __mask = SMC_inw(ioaddr, INT_REG(lp)) & ~0xff; \ + SMC_outw(lp, __mask | (x), ioaddr, INT_REG(lp)); \ + local_irq_restore(__flags); \ + } \ + } while (0) + +#define SMC_GET_INT_MASK(lp) \ + (SMC_8BIT(lp) ? (SMC_inb(ioaddr, IM_REG(lp))) \ + : (SMC_inw(ioaddr, INT_REG(lp)) >> 8)) + +#define SMC_SET_INT_MASK(lp, x) \ + do { \ + if (SMC_8BIT(lp)) \ + SMC_outb(x, ioaddr, IM_REG(lp)); \ + else \ + SMC_outw(lp, (x) << 8, ioaddr, INT_REG(lp)); \ + } while (0) + +#define SMC_CURRENT_BANK(lp) SMC_inw(ioaddr, BANK_SELECT) + +#define SMC_SELECT_BANK(lp, x) \ + do { \ + if (SMC_MUST_ALIGN_WRITE(lp)) \ + SMC_outl((x)<<16, ioaddr, 12<<SMC_IO_SHIFT); \ + else \ + SMC_outw(lp, x, ioaddr, BANK_SELECT); \ + } while (0) + +#define SMC_GET_BASE(lp) SMC_inw(ioaddr, BASE_REG(lp)) + +#define SMC_SET_BASE(lp, x) SMC_outw(lp, x, ioaddr, BASE_REG(lp)) + +#define SMC_GET_CONFIG(lp) SMC_inw(ioaddr, CONFIG_REG(lp)) + +#define SMC_SET_CONFIG(lp, x) SMC_outw(lp, x, ioaddr, CONFIG_REG(lp)) + +#define SMC_GET_COUNTER(lp) SMC_inw(ioaddr, COUNTER_REG(lp)) + +#define SMC_GET_CTL(lp) SMC_inw(ioaddr, CTL_REG(lp)) + +#define SMC_SET_CTL(lp, x) SMC_outw(lp, x, ioaddr, CTL_REG(lp)) + +#define SMC_GET_MII(lp) SMC_inw(ioaddr, MII_REG(lp)) + +#define SMC_GET_GP(lp) SMC_inw(ioaddr, GP_REG(lp)) + +#define SMC_SET_GP(lp, x) \ + do { \ + if (SMC_MUST_ALIGN_WRITE(lp)) \ + SMC_outl((x)<<16, ioaddr, SMC_REG(lp, 8, 1)); \ + else \ + SMC_outw(lp, x, ioaddr, GP_REG(lp)); \ + } while (0) + +#define SMC_SET_MII(lp, x) SMC_outw(lp, x, ioaddr, MII_REG(lp)) + +#define SMC_GET_MIR(lp) SMC_inw(ioaddr, MIR_REG(lp)) + +#define SMC_SET_MIR(lp, x) SMC_outw(lp, x, ioaddr, MIR_REG(lp)) + +#define SMC_GET_MMU_CMD(lp) SMC_inw(ioaddr, MMU_CMD_REG(lp)) + +#define SMC_SET_MMU_CMD(lp, x) SMC_outw(lp, x, ioaddr, MMU_CMD_REG(lp)) + +#define SMC_GET_FIFO(lp) SMC_inw(ioaddr, FIFO_REG(lp)) + +#define SMC_GET_PTR(lp) SMC_inw(ioaddr, PTR_REG(lp)) + +#define SMC_SET_PTR(lp, x) \ + do { \ + if (SMC_MUST_ALIGN_WRITE(lp)) \ + SMC_outl((x)<<16, ioaddr, SMC_REG(lp, 4, 2)); \ + else \ + SMC_outw(lp, x, ioaddr, PTR_REG(lp)); \ + } while (0) + +#define SMC_GET_EPH_STATUS(lp) SMC_inw(ioaddr, EPH_STATUS_REG(lp)) + +#define SMC_GET_RCR(lp) SMC_inw(ioaddr, RCR_REG(lp)) + +#define SMC_SET_RCR(lp, x) SMC_outw(lp, x, ioaddr, RCR_REG(lp)) + +#define SMC_GET_REV(lp) SMC_inw(ioaddr, REV_REG(lp)) + +#define SMC_GET_RPC(lp) SMC_inw(ioaddr, RPC_REG(lp)) + +#define SMC_SET_RPC(lp, x) \ + do { \ + if (SMC_MUST_ALIGN_WRITE(lp)) \ + SMC_outl((x)<<16, ioaddr, SMC_REG(lp, 8, 0)); \ + else \ + SMC_outw(lp, x, ioaddr, RPC_REG(lp)); \ + } while (0) + +#define SMC_GET_TCR(lp) SMC_inw(ioaddr, TCR_REG(lp)) + +#define SMC_SET_TCR(lp, x) SMC_outw(lp, x, ioaddr, TCR_REG(lp)) + +#ifndef SMC_GET_MAC_ADDR +#define SMC_GET_MAC_ADDR(lp, addr) \ + do { \ + unsigned int __v; \ + __v = SMC_inw(ioaddr, ADDR0_REG(lp)); \ + addr[0] = __v; addr[1] = __v >> 8; \ + __v = SMC_inw(ioaddr, ADDR1_REG(lp)); \ + addr[2] = __v; addr[3] = __v >> 8; \ + __v = SMC_inw(ioaddr, ADDR2_REG(lp)); \ + addr[4] = __v; addr[5] = __v >> 8; \ + } while (0) +#endif + +#define SMC_SET_MAC_ADDR(lp, addr) \ + do { \ + SMC_outw(lp, addr[0] | (addr[1] << 8), ioaddr, ADDR0_REG(lp)); \ + SMC_outw(lp, addr[2] | (addr[3] << 8), ioaddr, ADDR1_REG(lp)); \ + SMC_outw(lp, addr[4] | (addr[5] << 8), ioaddr, ADDR2_REG(lp)); \ + } while (0) + +#define SMC_SET_MCAST(lp, x) \ + do { \ + const unsigned char *mt = (x); \ + SMC_outw(lp, mt[0] | (mt[1] << 8), ioaddr, MCAST_REG1(lp)); \ + SMC_outw(lp, mt[2] | (mt[3] << 8), ioaddr, MCAST_REG2(lp)); \ + SMC_outw(lp, mt[4] | (mt[5] << 8), ioaddr, MCAST_REG3(lp)); \ + SMC_outw(lp, mt[6] | (mt[7] << 8), ioaddr, MCAST_REG4(lp)); \ + } while (0) + +#define SMC_PUT_PKT_HDR(lp, status, length) \ + do { \ + if (SMC_32BIT(lp)) \ + SMC_outl((status) | (length)<<16, ioaddr, \ + DATA_REG(lp)); \ + else { \ + SMC_outw(lp, status, ioaddr, DATA_REG(lp)); \ + SMC_outw(lp, length, ioaddr, DATA_REG(lp)); \ + } \ + } while (0) + +#define SMC_GET_PKT_HDR(lp, status, length) \ + do { \ + if (SMC_32BIT(lp)) { \ + unsigned int __val = SMC_inl(ioaddr, DATA_REG(lp)); \ + (status) = __val & 0xffff; \ + (length) = __val >> 16; \ + } else { \ + (status) = SMC_inw(ioaddr, DATA_REG(lp)); \ + (length) = SMC_inw(ioaddr, DATA_REG(lp)); \ + } \ + } while (0) + +#define SMC_PUSH_DATA(lp, p, l) \ + do { \ + if (SMC_32BIT(lp)) { \ + void *__ptr = (p); \ + int __len = (l); \ + void __iomem *__ioaddr = ioaddr; \ + if (__len >= 2 && (unsigned long)__ptr & 2) { \ + __len -= 2; \ + SMC_outsw(ioaddr, DATA_REG(lp), __ptr, 1); \ + __ptr += 2; \ + } \ + if (SMC_CAN_USE_DATACS && lp->datacs) \ + __ioaddr = lp->datacs; \ + SMC_outsl(__ioaddr, DATA_REG(lp), __ptr, __len>>2); \ + if (__len & 2) { \ + __ptr += (__len & ~3); \ + SMC_outsw(ioaddr, DATA_REG(lp), __ptr, 1); \ + } \ + } else if (SMC_16BIT(lp)) \ + SMC_outsw(ioaddr, DATA_REG(lp), p, (l) >> 1); \ + else if (SMC_8BIT(lp)) \ + SMC_outsb(ioaddr, DATA_REG(lp), p, l); \ + } while (0) + +#define SMC_PULL_DATA(lp, p, l) \ + do { \ + if (SMC_32BIT(lp)) { \ + void *__ptr = (p); \ + int __len = (l); \ + void __iomem *__ioaddr = ioaddr; \ + if ((unsigned long)__ptr & 2) { \ + /* \ + * We want 32bit alignment here. \ + * Since some buses perform a full \ + * 32bit fetch even for 16bit data \ + * we can't use SMC_inw() here. \ + * Back both source (on-chip) and \ + * destination pointers of 2 bytes. \ + * This is possible since the call to \ + * SMC_GET_PKT_HDR() already advanced \ + * the source pointer of 4 bytes, and \ + * the skb_reserve(skb, 2) advanced \ + * the destination pointer of 2 bytes. \ + */ \ + __ptr -= 2; \ + __len += 2; \ + SMC_SET_PTR(lp, \ + 2|PTR_READ|PTR_RCV|PTR_AUTOINC); \ + } \ + if (SMC_CAN_USE_DATACS && lp->datacs) \ + __ioaddr = lp->datacs; \ + __len += 2; \ + SMC_insl(__ioaddr, DATA_REG(lp), __ptr, __len>>2); \ + } else if (SMC_16BIT(lp)) \ + SMC_insw(ioaddr, DATA_REG(lp), p, (l) >> 1); \ + else if (SMC_8BIT(lp)) \ + SMC_insb(ioaddr, DATA_REG(lp), p, l); \ + } while (0) + +#endif /* _SMC91X_H_ */ |