diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/net/ethernet/sun/cassini.h | 2900 |
1 files changed, 2900 insertions, 0 deletions
diff --git a/drivers/net/ethernet/sun/cassini.h b/drivers/net/ethernet/sun/cassini.h new file mode 100644 index 000000000..2d91f4936 --- /dev/null +++ b/drivers/net/ethernet/sun/cassini.h @@ -0,0 +1,2900 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* $Id: cassini.h,v 1.16 2004/08/17 21:15:16 zaumen Exp $ + * cassini.h: Definitions for Sun Microsystems Cassini(+) ethernet driver. + * + * Copyright (C) 2004 Sun Microsystems Inc. + * Copyright (c) 2003 Adrian Sun (asun@darksunrising.com) + * + * vendor id: 0x108E (Sun Microsystems, Inc.) + * device id: 0xabba (Cassini) + * revision ids: 0x01 = Cassini + * 0x02 = Cassini rev 2 + * 0x10 = Cassini+ + * 0x11 = Cassini+ 0.2u + * + * vendor id: 0x100b (National Semiconductor) + * device id: 0x0035 (DP83065/Saturn) + * revision ids: 0x30 = Saturn B2 + * + * rings are all offset from 0. + * + * there are two clock domains: + * PCI: 33/66MHz clock + * chip: 125MHz clock + */ + +#ifndef _CASSINI_H +#define _CASSINI_H + +/* cassini register map: 2M memory mapped in 32-bit memory space accessible as + * 32-bit words. there is no i/o port access. REG_ addresses are + * shared between cassini and cassini+. REG_PLUS_ addresses only + * appear in cassini+. REG_MINUS_ addresses only appear in cassini. + */ +#define CAS_ID_REV2 0x02 +#define CAS_ID_REVPLUS 0x10 +#define CAS_ID_REVPLUS02u 0x11 +#define CAS_ID_REVSATURNB2 0x30 + +/** global resources **/ + +/* this register sets the weights for the weighted round robin arbiter. e.g., + * if rx weight == 1 and tx weight == 0, rx == 2x tx transfer credit + * for its next turn to access the pci bus. + * map: 0x0 = x1, 0x1 = x2, 0x2 = x4, 0x3 = x8 + * DEFAULT: 0x0, SIZE: 5 bits + */ +#define REG_CAWR 0x0004 /* core arbitration weight */ +#define CAWR_RX_DMA_WEIGHT_SHIFT 0 +#define CAWR_RX_DMA_WEIGHT_MASK 0x03 /* [0:1] */ +#define CAWR_TX_DMA_WEIGHT_SHIFT 2 +#define CAWR_TX_DMA_WEIGHT_MASK 0x0C /* [3:2] */ +#define CAWR_RR_DIS 0x10 /* [4] */ + +/* if enabled, BIM can send bursts across PCI bus > cacheline size. burst + * sizes determined by length of packet or descriptor transfer and the + * max length allowed by the target. + * DEFAULT: 0x0, SIZE: 1 bit + */ +#define REG_INF_BURST 0x0008 /* infinite burst enable reg */ +#define INF_BURST_EN 0x1 /* enable */ + +/* top level interrupts [0-9] are auto-cleared to 0 when the status + * register is read. second level interrupts [13 - 18] are cleared at + * the source. tx completion register 3 is replicated in [19 - 31] + * DEFAULT: 0x00000000, SIZE: 29 bits + */ +#define REG_INTR_STATUS 0x000C /* interrupt status register */ +#define INTR_TX_INTME 0x00000001 /* frame w/ INT ME desc bit set + xferred from host queue to + TX FIFO */ +#define INTR_TX_ALL 0x00000002 /* all xmit frames xferred into + TX FIFO. i.e., + TX Kick == TX complete. if + PACED_MODE set, then TX FIFO + also empty */ +#define INTR_TX_DONE 0x00000004 /* any frame xferred into tx + FIFO */ +#define INTR_TX_TAG_ERROR 0x00000008 /* TX FIFO tag framing + corrupted. FATAL ERROR */ +#define INTR_RX_DONE 0x00000010 /* at least 1 frame xferred + from RX FIFO to host mem. + RX completion reg updated. + may be delayed by recv + intr blanking. */ +#define INTR_RX_BUF_UNAVAIL 0x00000020 /* no more receive buffers. + RX Kick == RX complete */ +#define INTR_RX_TAG_ERROR 0x00000040 /* RX FIFO tag framing + corrupted. FATAL ERROR */ +#define INTR_RX_COMP_FULL 0x00000080 /* no more room in completion + ring to post descriptors. + RX complete head incr to + almost reach RX complete + tail */ +#define INTR_RX_BUF_AE 0x00000100 /* less than the + programmable threshold # + of free descr avail for + hw use */ +#define INTR_RX_COMP_AF 0x00000200 /* less than the + programmable threshold # + of descr spaces for hw + use in completion descr + ring */ +#define INTR_RX_LEN_MISMATCH 0x00000400 /* len field from MAC != + len of non-reassembly pkt + from fifo during DMA or + header parser provides TCP + header and payload size > + MAC packet size. + FATAL ERROR */ +#define INTR_SUMMARY 0x00001000 /* summary interrupt bit. this + bit will be set if an interrupt + generated on the pci bus. useful + when driver is polling for + interrupts */ +#define INTR_PCS_STATUS 0x00002000 /* PCS interrupt status register */ +#define INTR_TX_MAC_STATUS 0x00004000 /* TX MAC status register has at + least 1 unmasked interrupt set */ +#define INTR_RX_MAC_STATUS 0x00008000 /* RX MAC status register has at + least 1 unmasked interrupt set */ +#define INTR_MAC_CTRL_STATUS 0x00010000 /* MAC control status register has + at least 1 unmasked interrupt + set */ +#define INTR_MIF_STATUS 0x00020000 /* MIF status register has at least + 1 unmasked interrupt set */ +#define INTR_PCI_ERROR_STATUS 0x00040000 /* PCI error status register in the + BIF has at least 1 unmasked + interrupt set */ +#define INTR_TX_COMP_3_MASK 0xFFF80000 /* mask for TX completion + 3 reg data */ +#define INTR_TX_COMP_3_SHIFT 19 +#define INTR_ERROR_MASK (INTR_MIF_STATUS | INTR_PCI_ERROR_STATUS | \ + INTR_PCS_STATUS | INTR_RX_LEN_MISMATCH | \ + INTR_TX_MAC_STATUS | INTR_RX_MAC_STATUS | \ + INTR_TX_TAG_ERROR | INTR_RX_TAG_ERROR | \ + INTR_MAC_CTRL_STATUS) + +/* determines which status events will cause an interrupt. layout same + * as REG_INTR_STATUS. + * DEFAULT: 0xFFFFFFFF, SIZE: 16 bits + */ +#define REG_INTR_MASK 0x0010 /* Interrupt mask */ + +/* top level interrupt bits that are cleared during read of REG_INTR_STATUS_ALIAS. + * useful when driver is polling for interrupts. layout same as REG_INTR_MASK. + * DEFAULT: 0x00000000, SIZE: 12 bits + */ +#define REG_ALIAS_CLEAR 0x0014 /* alias clear mask + (used w/ status alias) */ +/* same as REG_INTR_STATUS except that only bits cleared are those selected by + * REG_ALIAS_CLEAR + * DEFAULT: 0x00000000, SIZE: 29 bits + */ +#define REG_INTR_STATUS_ALIAS 0x001C /* interrupt status alias + (selective clear) */ + +/* DEFAULT: 0x0, SIZE: 3 bits */ +#define REG_PCI_ERR_STATUS 0x1000 /* PCI error status */ +#define PCI_ERR_BADACK 0x01 /* reserved in Cassini+. + set if no ACK64# during ABS64 cycle + in Cassini. */ +#define PCI_ERR_DTRTO 0x02 /* delayed xaction timeout. set if + no read retry after 2^15 clocks */ +#define PCI_ERR_OTHER 0x04 /* other PCI errors */ +#define PCI_ERR_BIM_DMA_WRITE 0x08 /* BIM received 0 count DMA write req. + unused in Cassini. */ +#define PCI_ERR_BIM_DMA_READ 0x10 /* BIM received 0 count DMA read req. + unused in Cassini. */ +#define PCI_ERR_BIM_DMA_TIMEOUT 0x20 /* BIM received 255 retries during + DMA. unused in cassini. */ + +/* mask for PCI status events that will set PCI_ERR_STATUS. if cleared, event + * causes an interrupt to be generated. + * DEFAULT: 0x7, SIZE: 3 bits + */ +#define REG_PCI_ERR_STATUS_MASK 0x1004 /* PCI Error status mask */ + +/* used to configure PCI related parameters that are not in PCI config space. + * DEFAULT: 0bxx000, SIZE: 5 bits + */ +#define REG_BIM_CFG 0x1008 /* BIM Configuration */ +#define BIM_CFG_RESERVED0 0x001 /* reserved */ +#define BIM_CFG_RESERVED1 0x002 /* reserved */ +#define BIM_CFG_64BIT_DISABLE 0x004 /* disable 64-bit mode */ +#define BIM_CFG_66MHZ 0x008 /* (ro) 1 = 66MHz, 0 = < 66MHz */ +#define BIM_CFG_32BIT 0x010 /* (ro) 1 = 32-bit slot, 0 = 64-bit */ +#define BIM_CFG_DPAR_INTR_ENABLE 0x020 /* detected parity err enable */ +#define BIM_CFG_RMA_INTR_ENABLE 0x040 /* master abort intr enable */ +#define BIM_CFG_RTA_INTR_ENABLE 0x080 /* target abort intr enable */ +#define BIM_CFG_RESERVED2 0x100 /* reserved */ +#define BIM_CFG_BIM_DISABLE 0x200 /* stop BIM DMA. use before global + reset. reserved in Cassini. */ +#define BIM_CFG_BIM_STATUS 0x400 /* (ro) 1 = BIM DMA suspended. + reserved in Cassini. */ +#define BIM_CFG_PERROR_BLOCK 0x800 /* block PERR# to pci bus. def: 0. + reserved in Cassini. */ + +/* DEFAULT: 0x00000000, SIZE: 32 bits */ +#define REG_BIM_DIAG 0x100C /* BIM Diagnostic */ +#define BIM_DIAG_MSTR_SM_MASK 0x3FFFFF00 /* PCI master controller state + machine bits [21:0] */ +#define BIM_DIAG_BRST_SM_MASK 0x7F /* PCI burst controller state + machine bits [6:0] */ + +/* writing to SW_RESET_TX and SW_RESET_RX will issue a global + * reset. poll until TX and RX read back as 0's for completion. + */ +#define REG_SW_RESET 0x1010 /* Software reset */ +#define SW_RESET_TX 0x00000001 /* reset TX DMA engine. poll until + cleared to 0. */ +#define SW_RESET_RX 0x00000002 /* reset RX DMA engine. poll until + cleared to 0. */ +#define SW_RESET_RSTOUT 0x00000004 /* force RSTOUT# pin active (low). + resets PHY and anything else + connected to RSTOUT#. RSTOUT# + is also activated by local PCI + reset when hot-swap is being + done. */ +#define SW_RESET_BLOCK_PCS_SLINK 0x00000008 /* if a global reset is done with + this bit set, PCS and SLINK + modules won't be reset. + i.e., link won't drop. */ +#define SW_RESET_BREQ_SM_MASK 0x00007F00 /* breq state machine [6:0] */ +#define SW_RESET_PCIARB_SM_MASK 0x00070000 /* pci arbitration state bits: + 0b000: ARB_IDLE1 + 0b001: ARB_IDLE2 + 0b010: ARB_WB_ACK + 0b011: ARB_WB_WAT + 0b100: ARB_RB_ACK + 0b101: ARB_RB_WAT + 0b110: ARB_RB_END + 0b111: ARB_WB_END */ +#define SW_RESET_RDPCI_SM_MASK 0x00300000 /* read pci state bits: + 0b00: RD_PCI_WAT + 0b01: RD_PCI_RDY + 0b11: RD_PCI_ACK */ +#define SW_RESET_RDARB_SM_MASK 0x00C00000 /* read arbitration state bits: + 0b00: AD_IDL_RX + 0b01: AD_ACK_RX + 0b10: AD_ACK_TX + 0b11: AD_IDL_TX */ +#define SW_RESET_WRPCI_SM_MASK 0x06000000 /* write pci state bits + 0b00: WR_PCI_WAT + 0b01: WR_PCI_RDY + 0b11: WR_PCI_ACK */ +#define SW_RESET_WRARB_SM_MASK 0x38000000 /* write arbitration state bits: + 0b000: ARB_IDLE1 + 0b001: ARB_IDLE2 + 0b010: ARB_TX_ACK + 0b011: ARB_TX_WAT + 0b100: ARB_RX_ACK + 0b110: ARB_RX_WAT */ + +/* Cassini only. 64-bit register used to check PCI datapath. when read, + * value written has both lower and upper 32-bit halves rotated to the right + * one bit position. e.g., FFFFFFFF FFFFFFFF -> 7FFFFFFF 7FFFFFFF + */ +#define REG_MINUS_BIM_DATAPATH_TEST 0x1018 /* Cassini: BIM datapath test + Cassini+: reserved */ + +/* output enables are provided for each device's chip select and for the rest + * of the outputs from cassini to its local bus devices. two sw programmable + * bits are connected to general purpus control/status bits. + * DEFAULT: 0x7 + */ +#define REG_BIM_LOCAL_DEV_EN 0x1020 /* BIM local device + output EN. default: 0x7 */ +#define BIM_LOCAL_DEV_PAD 0x01 /* address bus, RW signal, and + OE signal output enable on the + local bus interface. these + are shared between both local + bus devices. tristate when 0. */ +#define BIM_LOCAL_DEV_PROM 0x02 /* PROM chip select */ +#define BIM_LOCAL_DEV_EXT 0x04 /* secondary local bus device chip + select output enable */ +#define BIM_LOCAL_DEV_SOFT_0 0x08 /* sw programmable ctrl bit 0 */ +#define BIM_LOCAL_DEV_SOFT_1 0x10 /* sw programmable ctrl bit 1 */ +#define BIM_LOCAL_DEV_HW_RESET 0x20 /* internal hw reset. Cassini+ only. */ + +/* access 24 entry BIM read and write buffers. put address in REG_BIM_BUFFER_ADDR + * and read/write from/to it REG_BIM_BUFFER_DATA_LOW and _DATA_HI. + * _DATA_HI should be the last access of the sequence. + * DEFAULT: undefined + */ +#define REG_BIM_BUFFER_ADDR 0x1024 /* BIM buffer address. for + purposes. */ +#define BIM_BUFFER_ADDR_MASK 0x3F /* index (0 - 23) of buffer */ +#define BIM_BUFFER_WR_SELECT 0x40 /* write buffer access = 1 + read buffer access = 0 */ +/* DEFAULT: undefined */ +#define REG_BIM_BUFFER_DATA_LOW 0x1028 /* BIM buffer data low */ +#define REG_BIM_BUFFER_DATA_HI 0x102C /* BIM buffer data high */ + +/* set BIM_RAM_BIST_START to start built-in self test for BIM read buffer. + * bit auto-clears when done with status read from _SUMMARY and _PASS bits. + */ +#define REG_BIM_RAM_BIST 0x102C /* BIM RAM (read buffer) BIST + control/status */ +#define BIM_RAM_BIST_RD_START 0x01 /* start BIST for BIM read buffer */ +#define BIM_RAM_BIST_WR_START 0x02 /* start BIST for BIM write buffer. + Cassini only. reserved in + Cassini+. */ +#define BIM_RAM_BIST_RD_PASS 0x04 /* summary BIST pass status for read + buffer. */ +#define BIM_RAM_BIST_WR_PASS 0x08 /* summary BIST pass status for write + buffer. Cassini only. reserved + in Cassini+. */ +#define BIM_RAM_BIST_RD_LOW_PASS 0x10 /* read low bank passes BIST */ +#define BIM_RAM_BIST_RD_HI_PASS 0x20 /* read high bank passes BIST */ +#define BIM_RAM_BIST_WR_LOW_PASS 0x40 /* write low bank passes BIST. + Cassini only. reserved in + Cassini+. */ +#define BIM_RAM_BIST_WR_HI_PASS 0x80 /* write high bank passes BIST. + Cassini only. reserved in + Cassini+. */ + +/* ASUN: i'm not sure what this does as it's not in the spec. + * DEFAULT: 0xFC + */ +#define REG_BIM_DIAG_MUX 0x1030 /* BIM diagnostic probe mux + select register */ + +/* enable probe monitoring mode and select data appearing on the P_A* bus. bit + * values for _SEL_HI_MASK and _SEL_LOW_MASK: + * 0x0: internal probe[7:0] (pci arb state, wtc empty w, wtc full w, wtc empty w, + * wtc empty r, post pci) + * 0x1: internal probe[15:8] (pci wbuf comp, pci wpkt comp, pci rbuf comp, + * pci rpkt comp, txdma wr req, txdma wr ack, + * txdma wr rdy, txdma wr xfr done) + * 0x2: internal probe[23:16] (txdma rd req, txdma rd ack, txdma rd rdy, rxdma rd, + * rd arb state, rd pci state) + * 0x3: internal probe[31:24] (rxdma req, rxdma ack, rxdma rdy, wrarb state, + * wrpci state) + * 0x4: pci io probe[7:0] 0x5: pci io probe[15:8] + * 0x6: pci io probe[23:16] 0x7: pci io probe[31:24] + * 0x8: pci io probe[39:32] 0x9: pci io probe[47:40] + * 0xa: pci io probe[55:48] 0xb: pci io probe[63:56] + * the following are not available in Cassini: + * 0xc: rx probe[7:0] 0xd: tx probe[7:0] + * 0xe: hp probe[7:0] 0xf: mac probe[7:0] + */ +#define REG_PLUS_PROBE_MUX_SELECT 0x1034 /* Cassini+: PROBE MUX SELECT */ +#define PROBE_MUX_EN 0x80000000 /* allow probe signals to be + driven on local bus P_A[15:0] + for debugging */ +#define PROBE_MUX_SUB_MUX_MASK 0x0000FF00 /* select sub module probe signals: + 0x03 = mac[1:0] + 0x0C = rx[1:0] + 0x30 = tx[1:0] + 0xC0 = hp[1:0] */ +#define PROBE_MUX_SEL_HI_MASK 0x000000F0 /* select which module to appear + on P_A[15:8]. see above for + values. */ +#define PROBE_MUX_SEL_LOW_MASK 0x0000000F /* select which module to appear + on P_A[7:0]. see above for + values. */ + +/* values mean the same thing as REG_INTR_MASK excep that it's for INTB. + DEFAULT: 0x1F */ +#define REG_PLUS_INTR_MASK_1 0x1038 /* Cassini+: interrupt mask + register 2 for INTB */ +#define REG_PLUS_INTRN_MASK(x) (REG_PLUS_INTR_MASK_1 + ((x) - 1)*16) +/* bits correspond to both _MASK and _STATUS registers. _ALT corresponds to + * all of the alternate (2-4) INTR registers while _1 corresponds to only + * _MASK_1 and _STATUS_1 registers. + * DEFAULT: 0x7 for MASK registers, 0x0 for ALIAS_CLEAR registers + */ +#define INTR_RX_DONE_ALT 0x01 +#define INTR_RX_COMP_FULL_ALT 0x02 +#define INTR_RX_COMP_AF_ALT 0x04 +#define INTR_RX_BUF_UNAVAIL_1 0x08 +#define INTR_RX_BUF_AE_1 0x10 /* almost empty */ +#define INTRN_MASK_RX_EN 0x80 +#define INTRN_MASK_CLEAR_ALL (INTR_RX_DONE_ALT | \ + INTR_RX_COMP_FULL_ALT | \ + INTR_RX_COMP_AF_ALT | \ + INTR_RX_BUF_UNAVAIL_1 | \ + INTR_RX_BUF_AE_1) +#define REG_PLUS_INTR_STATUS_1 0x103C /* Cassini+: interrupt status + register 2 for INTB. default: 0x1F */ +#define REG_PLUS_INTRN_STATUS(x) (REG_PLUS_INTR_STATUS_1 + ((x) - 1)*16) +#define INTR_STATUS_ALT_INTX_EN 0x80 /* generate INTX when one of the + flags are set. enables desc ring. */ + +#define REG_PLUS_ALIAS_CLEAR_1 0x1040 /* Cassini+: alias clear mask + register 2 for INTB */ +#define REG_PLUS_ALIASN_CLEAR(x) (REG_PLUS_ALIAS_CLEAR_1 + ((x) - 1)*16) + +#define REG_PLUS_INTR_STATUS_ALIAS_1 0x1044 /* Cassini+: interrupt status + register alias 2 for INTB */ +#define REG_PLUS_INTRN_STATUS_ALIAS(x) (REG_PLUS_INTR_STATUS_ALIAS_1 + ((x) - 1)*16) + +#define REG_SATURN_PCFG 0x106c /* pin configuration register for + integrated macphy */ + +#define SATURN_PCFG_TLA 0x00000001 /* 1 = phy actled */ +#define SATURN_PCFG_FLA 0x00000002 /* 1 = phy link10led */ +#define SATURN_PCFG_CLA 0x00000004 /* 1 = phy link100led */ +#define SATURN_PCFG_LLA 0x00000008 /* 1 = phy link1000led */ +#define SATURN_PCFG_RLA 0x00000010 /* 1 = phy duplexled */ +#define SATURN_PCFG_PDS 0x00000020 /* phy debug mode. + 0 = normal */ +#define SATURN_PCFG_MTP 0x00000080 /* test point select */ +#define SATURN_PCFG_GMO 0x00000100 /* GMII observe. 1 = + GMII on SERDES pins for + monitoring. */ +#define SATURN_PCFG_FSI 0x00000200 /* 1 = freeze serdes/gmii. all + pins configed as outputs. + for power saving when using + internal phy. */ +#define SATURN_PCFG_LAD 0x00000800 /* 0 = mac core led ctrl + polarity from strapping + value. + 1 = mac core led ctrl + polarity active low. */ + + +/** transmit dma registers **/ +#define MAX_TX_RINGS_SHIFT 2 +#define MAX_TX_RINGS (1 << MAX_TX_RINGS_SHIFT) +#define MAX_TX_RINGS_MASK (MAX_TX_RINGS - 1) + +/* TX configuration. + * descr ring sizes size = 32 * (1 << n), n < 9. e.g., 0x8 = 8k. default: 0x8 + * DEFAULT: 0x3F000001 + */ +#define REG_TX_CFG 0x2004 /* TX config */ +#define TX_CFG_DMA_EN 0x00000001 /* enable TX DMA. if cleared, DMA + will stop after xfer of current + buffer has been completed. */ +#define TX_CFG_FIFO_PIO_SEL 0x00000002 /* TX DMA FIFO can be + accessed w/ FIFO addr + and data registers. + TX DMA should be + disabled. */ +#define TX_CFG_DESC_RING0_MASK 0x0000003C /* # desc entries in + ring 1. */ +#define TX_CFG_DESC_RING0_SHIFT 2 +#define TX_CFG_DESC_RINGN_MASK(a) (TX_CFG_DESC_RING0_MASK << (a)*4) +#define TX_CFG_DESC_RINGN_SHIFT(a) (TX_CFG_DESC_RING0_SHIFT + (a)*4) +#define TX_CFG_PACED_MODE 0x00100000 /* TX_ALL only set after + TX FIFO becomes empty. + if 0, TX_ALL set + if descr queue empty. */ +#define TX_CFG_DMA_RDPIPE_DIS 0x01000000 /* always set to 1 */ +#define TX_CFG_COMPWB_Q1 0x02000000 /* completion writeback happens at + the end of every packet kicked + through Q1. */ +#define TX_CFG_COMPWB_Q2 0x04000000 /* completion writeback happens at + the end of every packet kicked + through Q2. */ +#define TX_CFG_COMPWB_Q3 0x08000000 /* completion writeback happens at + the end of every packet kicked + through Q3 */ +#define TX_CFG_COMPWB_Q4 0x10000000 /* completion writeback happens at + the end of every packet kicked + through Q4 */ +#define TX_CFG_INTR_COMPWB_DIS 0x20000000 /* disable pre-interrupt completion + writeback */ +#define TX_CFG_CTX_SEL_MASK 0xC0000000 /* selects tx test port + connection + 0b00: tx mac req, + tx mac retry req, + tx ack and tx tag. + 0b01: txdma rd req, + txdma rd ack, + txdma rd rdy, + txdma rd type0 + 0b11: txdma wr req, + txdma wr ack, + txdma wr rdy, + txdma wr xfr done. */ +#define TX_CFG_CTX_SEL_SHIFT 30 + +/* 11-bit counters that point to next location in FIFO to be loaded/retrieved. + * used for diagnostics only. + */ +#define REG_TX_FIFO_WRITE_PTR 0x2014 /* TX FIFO write pointer */ +#define REG_TX_FIFO_SHADOW_WRITE_PTR 0x2018 /* TX FIFO shadow write + pointer. temp hold reg. + diagnostics only. */ +#define REG_TX_FIFO_READ_PTR 0x201C /* TX FIFO read pointer */ +#define REG_TX_FIFO_SHADOW_READ_PTR 0x2020 /* TX FIFO shadow read + pointer */ + +/* (ro) 11-bit up/down counter w/ # of frames currently in TX FIFO */ +#define REG_TX_FIFO_PKT_CNT 0x2024 /* TX FIFO packet counter */ + +/* current state of all state machines in TX */ +#define REG_TX_SM_1 0x2028 /* TX state machine reg #1 */ +#define TX_SM_1_CHAIN_MASK 0x000003FF /* chaining state machine */ +#define TX_SM_1_CSUM_MASK 0x00000C00 /* checksum state machine */ +#define TX_SM_1_FIFO_LOAD_MASK 0x0003F000 /* FIFO load state machine. + = 0x01 when TX disabled. */ +#define TX_SM_1_FIFO_UNLOAD_MASK 0x003C0000 /* FIFO unload state machine */ +#define TX_SM_1_CACHE_MASK 0x03C00000 /* desc. prefetch cache controller + state machine */ +#define TX_SM_1_CBQ_ARB_MASK 0xF8000000 /* CBQ arbiter state machine */ + +#define REG_TX_SM_2 0x202C /* TX state machine reg #2 */ +#define TX_SM_2_COMP_WB_MASK 0x07 /* completion writeback sm */ +#define TX_SM_2_SUB_LOAD_MASK 0x38 /* sub load state machine */ +#define TX_SM_2_KICK_MASK 0xC0 /* kick state machine */ + +/* 64-bit pointer to the transmit data buffer. only the 50 LSB are incremented + * while the upper 23 bits are taken from the TX descriptor + */ +#define REG_TX_DATA_PTR_LOW 0x2030 /* TX data pointer low */ +#define REG_TX_DATA_PTR_HI 0x2034 /* TX data pointer high */ + +/* 13 bit registers written by driver w/ descriptor value that follows + * last valid xmit descriptor. kick # and complete # values are used by + * the xmit dma engine to control tx descr fetching. if > 1 valid + * tx descr is available within the cache line being read, cassini will + * internally cache up to 4 of them. 0 on reset. _KICK = rw, _COMP = ro. + */ +#define REG_TX_KICK0 0x2038 /* TX kick reg #1 */ +#define REG_TX_KICKN(x) (REG_TX_KICK0 + (x)*4) +#define REG_TX_COMP0 0x2048 /* TX completion reg #1 */ +#define REG_TX_COMPN(x) (REG_TX_COMP0 + (x)*4) + +/* values of TX_COMPLETE_1-4 are written. each completion register + * is 2bytes in size and contiguous. 8B allocation w/ 8B alignment. + * NOTE: completion reg values are only written back prior to TX_INTME and + * TX_ALL interrupts. at all other times, the most up-to-date index values + * should be obtained from the REG_TX_COMPLETE_# registers. + * here's the layout: + * offset from base addr completion # byte + * 0 TX_COMPLETE_1_MSB + * 1 TX_COMPLETE_1_LSB + * 2 TX_COMPLETE_2_MSB + * 3 TX_COMPLETE_2_LSB + * 4 TX_COMPLETE_3_MSB + * 5 TX_COMPLETE_3_LSB + * 6 TX_COMPLETE_4_MSB + * 7 TX_COMPLETE_4_LSB + */ +#define TX_COMPWB_SIZE 8 +#define REG_TX_COMPWB_DB_LOW 0x2058 /* TX completion write back + base low */ +#define REG_TX_COMPWB_DB_HI 0x205C /* TX completion write back + base high */ +#define TX_COMPWB_MSB_MASK 0x00000000000000FFULL +#define TX_COMPWB_MSB_SHIFT 0 +#define TX_COMPWB_LSB_MASK 0x000000000000FF00ULL +#define TX_COMPWB_LSB_SHIFT 8 +#define TX_COMPWB_NEXT(x) ((x) >> 16) + +/* 53 MSB used as base address. 11 LSB assumed to be 0. TX desc pointer must + * be 2KB-aligned. */ +#define REG_TX_DB0_LOW 0x2060 /* TX descriptor base low #1 */ +#define REG_TX_DB0_HI 0x2064 /* TX descriptor base hi #1 */ +#define REG_TX_DBN_LOW(x) (REG_TX_DB0_LOW + (x)*8) +#define REG_TX_DBN_HI(x) (REG_TX_DB0_HI + (x)*8) + +/* 16-bit registers hold weights for the weighted round-robin of the + * four CBQ TX descr rings. weights correspond to # bytes xferred from + * host to TXFIFO in a round of WRR arbitration. can be set + * dynamically with new weights set upon completion of the current + * packet transfer from host memory to TXFIFO. a dummy write to any of + * these registers causes a queue1 pre-emption with all historical bw + * deficit data reset to 0 (useful when congestion requires a + * pre-emption/re-allocation of network bandwidth + */ +#define REG_TX_MAXBURST_0 0x2080 /* TX MaxBurst #1 */ +#define REG_TX_MAXBURST_1 0x2084 /* TX MaxBurst #2 */ +#define REG_TX_MAXBURST_2 0x2088 /* TX MaxBurst #3 */ +#define REG_TX_MAXBURST_3 0x208C /* TX MaxBurst #4 */ + +/* diagnostics access to any TX FIFO location. every access is 65 + * bits. _DATA_LOW = 32 LSB, _DATA_HI_T1/T0 = 32 MSB. _TAG = tag bit. + * writing _DATA_HI_T0 sets tag bit low, writing _DATA_HI_T1 sets tag + * bit high. TX_FIFO_PIO_SEL must be set for TX FIFO PIO access. if + * TX FIFO data integrity is desired, TX DMA should be + * disabled. _DATA_HI_Tx should be the last access of the sequence. + */ +#define REG_TX_FIFO_ADDR 0x2104 /* TX FIFO address */ +#define REG_TX_FIFO_TAG 0x2108 /* TX FIFO tag */ +#define REG_TX_FIFO_DATA_LOW 0x210C /* TX FIFO data low */ +#define REG_TX_FIFO_DATA_HI_T1 0x2110 /* TX FIFO data high t1 */ +#define REG_TX_FIFO_DATA_HI_T0 0x2114 /* TX FIFO data high t0 */ +#define REG_TX_FIFO_SIZE 0x2118 /* (ro) TX FIFO size = 0x090 = 9KB */ + +/* 9-bit register controls BIST of TX FIFO. bit set indicates that the BIST + * passed for the specified memory + */ +#define REG_TX_RAMBIST 0x211C /* TX RAMBIST control/status */ +#define TX_RAMBIST_STATE 0x01C0 /* progress state of RAMBIST + controller state machine */ +#define TX_RAMBIST_RAM33A_PASS 0x0020 /* RAM33A passed */ +#define TX_RAMBIST_RAM32A_PASS 0x0010 /* RAM32A passed */ +#define TX_RAMBIST_RAM33B_PASS 0x0008 /* RAM33B passed */ +#define TX_RAMBIST_RAM32B_PASS 0x0004 /* RAM32B passed */ +#define TX_RAMBIST_SUMMARY 0x0002 /* all RAM passed */ +#define TX_RAMBIST_START 0x0001 /* write 1 to start BIST. self + clears on completion. */ + +/** receive dma registers **/ +#define MAX_RX_DESC_RINGS 2 +#define MAX_RX_COMP_RINGS 4 + +/* receive DMA channel configuration. default: 0x80910 + * free ring size = (1 << n)*32 -> [32 - 8k] + * completion ring size = (1 << n)*128 -> [128 - 32k], n < 9 + * DEFAULT: 0x80910 + */ +#define REG_RX_CFG 0x4000 /* RX config */ +#define RX_CFG_DMA_EN 0x00000001 /* enable RX DMA. 0 stops + channel as soon as current + frame xfer has completed. + driver should disable MAC + for 200ms before disabling + RX */ +#define RX_CFG_DESC_RING_MASK 0x0000001E /* # desc entries in RX + free desc ring. + def: 0x8 = 8k */ +#define RX_CFG_DESC_RING_SHIFT 1 +#define RX_CFG_COMP_RING_MASK 0x000001E0 /* # desc entries in RX complete + ring. def: 0x8 = 32k */ +#define RX_CFG_COMP_RING_SHIFT 5 +#define RX_CFG_BATCH_DIS 0x00000200 /* disable receive desc + batching. def: 0x0 = + enabled */ +#define RX_CFG_SWIVEL_MASK 0x00001C00 /* byte offset of the 1st + data byte of the packet + w/in 8 byte boundares. + this swivels the data + DMA'ed to header + buffers, jumbo buffers + when header split is not + requested and MTU sized + buffers. def: 0x2 */ +#define RX_CFG_SWIVEL_SHIFT 10 + +/* cassini+ only */ +#define RX_CFG_DESC_RING1_MASK 0x000F0000 /* # of desc entries in + RX free desc ring 2. + def: 0x8 = 8k */ +#define RX_CFG_DESC_RING1_SHIFT 16 + + +/* the page size register allows cassini chips to do the following with + * received data: + * [--------------------------------------------------------------] page + * [off][buf1][pad][off][buf2][pad][off][buf3][pad][off][buf4][pad] + * |--------------| = PAGE_SIZE_BUFFER_STRIDE + * page = PAGE_SIZE + * offset = PAGE_SIZE_MTU_OFF + * for the above example, MTU_BUFFER_COUNT = 4. + * NOTE: as is apparent, you need to ensure that the following holds: + * MTU_BUFFER_COUNT <= PAGE_SIZE/PAGE_SIZE_BUFFER_STRIDE + * DEFAULT: 0x48002002 (8k pages) + */ +#define REG_RX_PAGE_SIZE 0x4004 /* RX page size */ +#define RX_PAGE_SIZE_MASK 0x00000003 /* size of pages pointed to + by receive descriptors. + if jumbo buffers are + supported the page size + should not be < 8k. + 0b00 = 2k, 0b01 = 4k + 0b10 = 8k, 0b11 = 16k + DEFAULT: 8k */ +#define RX_PAGE_SIZE_SHIFT 0 +#define RX_PAGE_SIZE_MTU_COUNT_MASK 0x00007800 /* # of MTU buffers the hw + packs into a page. + DEFAULT: 4 */ +#define RX_PAGE_SIZE_MTU_COUNT_SHIFT 11 +#define RX_PAGE_SIZE_MTU_STRIDE_MASK 0x18000000 /* # of bytes that separate + each MTU buffer + + offset from each + other. + 0b00 = 1k, 0b01 = 2k + 0b10 = 4k, 0b11 = 8k + DEFAULT: 0x1 */ +#define RX_PAGE_SIZE_MTU_STRIDE_SHIFT 27 +#define RX_PAGE_SIZE_MTU_OFF_MASK 0xC0000000 /* offset in each page that + hw writes the MTU buffer + into. + 0b00 = 0, + 0b01 = 64 bytes + 0b10 = 96, 0b11 = 128 + DEFAULT: 0x1 */ +#define RX_PAGE_SIZE_MTU_OFF_SHIFT 30 + +/* 11-bit counter points to next location in RX FIFO to be loaded/read. + * shadow write pointers enable retries in case of early receive aborts. + * DEFAULT: 0x0. generated on 64-bit boundaries. + */ +#define REG_RX_FIFO_WRITE_PTR 0x4008 /* RX FIFO write pointer */ +#define REG_RX_FIFO_READ_PTR 0x400C /* RX FIFO read pointer */ +#define REG_RX_IPP_FIFO_SHADOW_WRITE_PTR 0x4010 /* RX IPP FIFO shadow write + pointer */ +#define REG_RX_IPP_FIFO_SHADOW_READ_PTR 0x4014 /* RX IPP FIFO shadow read + pointer */ +#define REG_RX_IPP_FIFO_READ_PTR 0x400C /* RX IPP FIFO read + pointer. (8-bit counter) */ + +/* current state of RX DMA state engines + other info + * DEFAULT: 0x0 + */ +#define REG_RX_DEBUG 0x401C /* RX debug */ +#define RX_DEBUG_LOAD_STATE_MASK 0x0000000F /* load state machine w/ MAC: + 0x0 = idle, 0x1 = load_bop + 0x2 = load 1, 0x3 = load 2 + 0x4 = load 3, 0x5 = load 4 + 0x6 = last detect + 0x7 = wait req + 0x8 = wait req statuss 1st + 0x9 = load st + 0xa = bubble mac + 0xb = error */ +#define RX_DEBUG_LM_STATE_MASK 0x00000070 /* load state machine w/ HP and + RX FIFO: + 0x0 = idle, 0x1 = hp xfr + 0x2 = wait hp ready + 0x3 = wait flow code + 0x4 = fifo xfer + 0x5 = make status + 0x6 = csum ready + 0x7 = error */ +#define RX_DEBUG_FC_STATE_MASK 0x000000180 /* flow control state machine + w/ MAC: + 0x0 = idle + 0x1 = wait xoff ack + 0x2 = wait xon + 0x3 = wait xon ack */ +#define RX_DEBUG_DATA_STATE_MASK 0x000001E00 /* unload data state machine + states: + 0x0 = idle data + 0x1 = header begin + 0x2 = xfer header + 0x3 = xfer header ld + 0x4 = mtu begin + 0x5 = xfer mtu + 0x6 = xfer mtu ld + 0x7 = jumbo begin + 0x8 = xfer jumbo + 0x9 = xfer jumbo ld + 0xa = reas begin + 0xb = xfer reas + 0xc = flush tag + 0xd = xfer reas ld + 0xe = error + 0xf = bubble idle */ +#define RX_DEBUG_DESC_STATE_MASK 0x0001E000 /* unload desc state machine + states: + 0x0 = idle desc + 0x1 = wait ack + 0x9 = wait ack 2 + 0x2 = fetch desc 1 + 0xa = fetch desc 2 + 0x3 = load ptrs + 0x4 = wait dma + 0x5 = wait ack batch + 0x6 = post batch + 0x7 = xfr done */ +#define RX_DEBUG_INTR_READ_PTR_MASK 0x30000000 /* interrupt read ptr of the + interrupt queue */ +#define RX_DEBUG_INTR_WRITE_PTR_MASK 0xC0000000 /* interrupt write pointer + of the interrupt queue */ + +/* flow control frames are emitted using two PAUSE thresholds: + * XOFF PAUSE uses pause time value pre-programmed in the Send PAUSE MAC reg + * XON PAUSE uses a pause time of 0. granularity of threshold is 64bytes. + * PAUSE thresholds defined in terms of FIFO occupancy and may be translated + * into FIFO vacancy using RX_FIFO_SIZE. setting ON will trigger XON frames + * when FIFO reaches 0. OFF threshold should not be > size of RX FIFO. max + * value is 0x6F. + * DEFAULT: 0x00078 + */ +#define REG_RX_PAUSE_THRESH 0x4020 /* RX pause thresholds */ +#define RX_PAUSE_THRESH_QUANTUM 64 +#define RX_PAUSE_THRESH_OFF_MASK 0x000001FF /* XOFF PAUSE emitted when + RX FIFO occupancy > + value*64B */ +#define RX_PAUSE_THRESH_OFF_SHIFT 0 +#define RX_PAUSE_THRESH_ON_MASK 0x001FF000 /* XON PAUSE emitted after + emitting XOFF PAUSE when RX + FIFO occupancy falls below + this value*64B. must be + < XOFF threshold. if = + RX_FIFO_SIZE< XON frames are + never emitted. */ +#define RX_PAUSE_THRESH_ON_SHIFT 12 + +/* 13-bit register used to control RX desc fetching and intr generation. if 4+ + * valid RX descriptors are available, Cassini will read 4 at a time. + * writing N means that all desc up to *but* excluding N are available. N must + * be a multiple of 4 (N % 4 = 0). first desc should be cache-line aligned. + * DEFAULT: 0 on reset + */ +#define REG_RX_KICK 0x4024 /* RX kick reg */ + +/* 8KB aligned 64-bit pointer to the base of the RX free/completion rings. + * lower 13 bits of the low register are hard-wired to 0. + */ +#define REG_RX_DB_LOW 0x4028 /* RX descriptor ring + base low */ +#define REG_RX_DB_HI 0x402C /* RX descriptor ring + base hi */ +#define REG_RX_CB_LOW 0x4030 /* RX completion ring + base low */ +#define REG_RX_CB_HI 0x4034 /* RX completion ring + base hi */ +/* 13-bit register indicate desc used by cassini for receive frames. used + * for diagnostic purposes. + * DEFAULT: 0 on reset + */ +#define REG_RX_COMP 0x4038 /* (ro) RX completion */ + +/* HEAD and TAIL are used to control RX desc posting and interrupt + * generation. hw moves the head register to pass ownership to sw. sw + * moves the tail register to pass ownership back to hw. to give all + * entries to hw, set TAIL = HEAD. if HEAD and TAIL indicate that no + * more entries are available, DMA will pause and an interrupt will be + * generated to indicate no more entries are available. sw can use + * this interrupt to reduce the # of times it must update the + * completion tail register. + * DEFAULT: 0 on reset + */ +#define REG_RX_COMP_HEAD 0x403C /* RX completion head */ +#define REG_RX_COMP_TAIL 0x4040 /* RX completion tail */ + +/* values used for receive interrupt blanking. loaded each time the ISR is read + * DEFAULT: 0x00000000 + */ +#define REG_RX_BLANK 0x4044 /* RX blanking register + for ISR read */ +#define RX_BLANK_INTR_PKT_MASK 0x000001FF /* RX_DONE intr asserted if + this many sets of completion + writebacks (up to 2 packets) + occur since the last time + the ISR was read. 0 = no + packet blanking */ +#define RX_BLANK_INTR_PKT_SHIFT 0 +#define RX_BLANK_INTR_TIME_MASK 0x3FFFF000 /* RX_DONE interrupt asserted + if that many clocks were + counted since last time the + ISR was read. + each count is 512 core + clocks (125MHz). 0 = no + time blanking */ +#define RX_BLANK_INTR_TIME_SHIFT 12 + +/* values used for interrupt generation based on threshold values of how + * many free desc and completion entries are available for hw use. + * DEFAULT: 0x00000000 + */ +#define REG_RX_AE_THRESH 0x4048 /* RX almost empty + thresholds */ +#define RX_AE_THRESH_FREE_MASK 0x00001FFF /* RX_BUF_AE will be + generated if # desc + avail for hw use <= + # */ +#define RX_AE_THRESH_FREE_SHIFT 0 +#define RX_AE_THRESH_COMP_MASK 0x0FFFE000 /* RX_COMP_AE will be + generated if # of + completion entries + avail for hw use <= + # */ +#define RX_AE_THRESH_COMP_SHIFT 13 + +/* probabilities for random early drop (RED) thresholds on a FIFO threshold + * basis. probability should increase when the FIFO level increases. control + * packets are never dropped and not counted in stats. probability programmed + * on a 12.5% granularity. e.g., 0x1 = 1/8 packets dropped. + * DEFAULT: 0x00000000 + */ +#define REG_RX_RED 0x404C /* RX random early detect enable */ +#define RX_RED_4K_6K_FIFO_MASK 0x000000FF /* 4KB < FIFO thresh < 6KB */ +#define RX_RED_6K_8K_FIFO_MASK 0x0000FF00 /* 6KB < FIFO thresh < 8KB */ +#define RX_RED_8K_10K_FIFO_MASK 0x00FF0000 /* 8KB < FIFO thresh < 10KB */ +#define RX_RED_10K_12K_FIFO_MASK 0xFF000000 /* 10KB < FIFO thresh < 12KB */ + +/* FIFO fullness levels for RX FIFO, RX control FIFO, and RX IPP FIFO. + * RX control FIFO = # of packets in RX FIFO. + * DEFAULT: 0x0 + */ +#define REG_RX_FIFO_FULLNESS 0x4050 /* (ro) RX FIFO fullness */ +#define RX_FIFO_FULLNESS_RX_FIFO_MASK 0x3FF80000 /* level w/ 8B granularity */ +#define RX_FIFO_FULLNESS_IPP_FIFO_MASK 0x0007FF00 /* level w/ 8B granularity */ +#define RX_FIFO_FULLNESS_RX_PKT_MASK 0x000000FF /* # packets in RX FIFO */ +#define REG_RX_IPP_PACKET_COUNT 0x4054 /* RX IPP packet counter */ +#define REG_RX_WORK_DMA_PTR_LOW 0x4058 /* RX working DMA ptr low */ +#define REG_RX_WORK_DMA_PTR_HI 0x405C /* RX working DMA ptr + high */ + +/* BIST testing ro RX FIFO, RX control FIFO, and RX IPP FIFO. only RX BIST + * START/COMPLETE is writeable. START will clear when the BIST has completed + * checking all 17 RAMS. + * DEFAULT: 0bxxxx xxxxx xxxx xxxx xxxx x000 0000 0000 00x0 + */ +#define REG_RX_BIST 0x4060 /* (ro) RX BIST */ +#define RX_BIST_32A_PASS 0x80000000 /* RX FIFO 32A passed */ +#define RX_BIST_33A_PASS 0x40000000 /* RX FIFO 33A passed */ +#define RX_BIST_32B_PASS 0x20000000 /* RX FIFO 32B passed */ +#define RX_BIST_33B_PASS 0x10000000 /* RX FIFO 33B passed */ +#define RX_BIST_32C_PASS 0x08000000 /* RX FIFO 32C passed */ +#define RX_BIST_33C_PASS 0x04000000 /* RX FIFO 33C passed */ +#define RX_BIST_IPP_32A_PASS 0x02000000 /* RX IPP FIFO 33B passed */ +#define RX_BIST_IPP_33A_PASS 0x01000000 /* RX IPP FIFO 33A passed */ +#define RX_BIST_IPP_32B_PASS 0x00800000 /* RX IPP FIFO 32B passed */ +#define RX_BIST_IPP_33B_PASS 0x00400000 /* RX IPP FIFO 33B passed */ +#define RX_BIST_IPP_32C_PASS 0x00200000 /* RX IPP FIFO 32C passed */ +#define RX_BIST_IPP_33C_PASS 0x00100000 /* RX IPP FIFO 33C passed */ +#define RX_BIST_CTRL_32_PASS 0x00800000 /* RX CTRL FIFO 32 passed */ +#define RX_BIST_CTRL_33_PASS 0x00400000 /* RX CTRL FIFO 33 passed */ +#define RX_BIST_REAS_26A_PASS 0x00200000 /* RX Reas 26A passed */ +#define RX_BIST_REAS_26B_PASS 0x00100000 /* RX Reas 26B passed */ +#define RX_BIST_REAS_27_PASS 0x00080000 /* RX Reas 27 passed */ +#define RX_BIST_STATE_MASK 0x00078000 /* BIST state machine */ +#define RX_BIST_SUMMARY 0x00000002 /* when BIST complete, + summary pass bit + contains AND of BIST + results of all 16 + RAMS */ +#define RX_BIST_START 0x00000001 /* write 1 to start + BIST. self clears + on completion. */ + +/* next location in RX CTRL FIFO that will be loaded w/ data from RX IPP/read + * from to retrieve packet control info. + * DEFAULT: 0 + */ +#define REG_RX_CTRL_FIFO_WRITE_PTR 0x4064 /* (ro) RX control FIFO + write ptr */ +#define REG_RX_CTRL_FIFO_READ_PTR 0x4068 /* (ro) RX control FIFO read + ptr */ + +/* receive interrupt blanking. loaded each time interrupt alias register is + * read. + * DEFAULT: 0x0 + */ +#define REG_RX_BLANK_ALIAS_READ 0x406C /* RX blanking register for + alias read */ +#define RX_BAR_INTR_PACKET_MASK 0x000001FF /* assert RX_DONE if # + completion writebacks + > # since last ISR + read. 0 = no + blanking. up to 2 + packets per + completion wb. */ +#define RX_BAR_INTR_TIME_MASK 0x3FFFF000 /* assert RX_DONE if # + clocks > # since last + ISR read. each count + is 512 core clocks + (125MHz). 0 = no + blanking. */ + +/* diagnostic access to RX FIFO. 32 LSB accessed via DATA_LOW. 32 MSB accessed + * via DATA_HI_T0 or DATA_HI_T1. TAG reads the tag bit. writing HI_T0 + * will unset the tag bit while writing HI_T1 will set the tag bit. to reset + * to normal operation after diagnostics, write to address location 0x0. + * RX_DMA_EN bit must be set to 0x0 for RX FIFO PIO access. DATA_HI should + * be the last write access of a write sequence. + * DEFAULT: undefined + */ +#define REG_RX_FIFO_ADDR 0x4080 /* RX FIFO address */ +#define REG_RX_FIFO_TAG 0x4084 /* RX FIFO tag */ +#define REG_RX_FIFO_DATA_LOW 0x4088 /* RX FIFO data low */ +#define REG_RX_FIFO_DATA_HI_T0 0x408C /* RX FIFO data high T0 */ +#define REG_RX_FIFO_DATA_HI_T1 0x4090 /* RX FIFO data high T1 */ + +/* diagnostic assess to RX CTRL FIFO. 8-bit FIFO_ADDR holds address of + * 81 bit control entry and 6 bit flow id. LOW and MID are both 32-bit + * accesses. HI is 7-bits with 6-bit flow id and 1 bit control + * word. RX_DMA_EN must be 0 for RX CTRL FIFO PIO access. DATA_HI + * should be last write access of the write sequence. + * DEFAULT: undefined + */ +#define REG_RX_CTRL_FIFO_ADDR 0x4094 /* RX Control FIFO and + Batching FIFO addr */ +#define REG_RX_CTRL_FIFO_DATA_LOW 0x4098 /* RX Control FIFO data + low */ +#define REG_RX_CTRL_FIFO_DATA_MID 0x409C /* RX Control FIFO data + mid */ +#define REG_RX_CTRL_FIFO_DATA_HI 0x4100 /* RX Control FIFO data + hi and flow id */ +#define RX_CTRL_FIFO_DATA_HI_CTRL 0x0001 /* upper bit of ctrl word */ +#define RX_CTRL_FIFO_DATA_HI_FLOW_MASK 0x007E /* flow id */ + +/* diagnostic access to RX IPP FIFO. same semantics as RX_FIFO. + * DEFAULT: undefined + */ +#define REG_RX_IPP_FIFO_ADDR 0x4104 /* RX IPP FIFO address */ +#define REG_RX_IPP_FIFO_TAG 0x4108 /* RX IPP FIFO tag */ +#define REG_RX_IPP_FIFO_DATA_LOW 0x410C /* RX IPP FIFO data low */ +#define REG_RX_IPP_FIFO_DATA_HI_T0 0x4110 /* RX IPP FIFO data high + T0 */ +#define REG_RX_IPP_FIFO_DATA_HI_T1 0x4114 /* RX IPP FIFO data high + T1 */ + +/* 64-bit pointer to receive data buffer in host memory used for headers and + * small packets. MSB in high register. loaded by DMA state machine and + * increments as DMA writes receive data. only 50 LSB are incremented. top + * 13 bits taken from RX descriptor. + * DEFAULT: undefined + */ +#define REG_RX_HEADER_PAGE_PTR_LOW 0x4118 /* (ro) RX header page ptr + low */ +#define REG_RX_HEADER_PAGE_PTR_HI 0x411C /* (ro) RX header page ptr + high */ +#define REG_RX_MTU_PAGE_PTR_LOW 0x4120 /* (ro) RX MTU page pointer + low */ +#define REG_RX_MTU_PAGE_PTR_HI 0x4124 /* (ro) RX MTU page pointer + high */ + +/* PIO diagnostic access to RX reassembly DMA Table RAM. 6-bit register holds + * one of 64 79-bit locations in the RX Reassembly DMA table and the addr of + * one of the 64 byte locations in the Batching table. LOW holds 32 LSB. + * MID holds the next 32 LSB. HIGH holds the 15 MSB. RX_DMA_EN must be set + * to 0 for PIO access. DATA_HIGH should be last write of write sequence. + * layout: + * reassmbl ptr [78:15] | reassmbl index [14:1] | reassmbl entry valid [0] + * DEFAULT: undefined + */ +#define REG_RX_TABLE_ADDR 0x4128 /* RX reassembly DMA table + address */ +#define RX_TABLE_ADDR_MASK 0x0000003F /* address mask */ + +#define REG_RX_TABLE_DATA_LOW 0x412C /* RX reassembly DMA table + data low */ +#define REG_RX_TABLE_DATA_MID 0x4130 /* RX reassembly DMA table + data mid */ +#define REG_RX_TABLE_DATA_HI 0x4134 /* RX reassembly DMA table + data high */ + +/* cassini+ only */ +/* 8KB aligned 64-bit pointer to base of RX rings. lower 13 bits hardwired to + * 0. same semantics as primary desc/complete rings. + */ +#define REG_PLUS_RX_DB1_LOW 0x4200 /* RX descriptor ring + 2 base low */ +#define REG_PLUS_RX_DB1_HI 0x4204 /* RX descriptor ring + 2 base high */ +#define REG_PLUS_RX_CB1_LOW 0x4208 /* RX completion ring + 2 base low. 4 total */ +#define REG_PLUS_RX_CB1_HI 0x420C /* RX completion ring + 2 base high. 4 total */ +#define REG_PLUS_RX_CBN_LOW(x) (REG_PLUS_RX_CB1_LOW + 8*((x) - 1)) +#define REG_PLUS_RX_CBN_HI(x) (REG_PLUS_RX_CB1_HI + 8*((x) - 1)) +#define REG_PLUS_RX_KICK1 0x4220 /* RX Kick 2 register */ +#define REG_PLUS_RX_COMP1 0x4224 /* (ro) RX completion 2 + reg */ +#define REG_PLUS_RX_COMP1_HEAD 0x4228 /* (ro) RX completion 2 + head reg. 4 total. */ +#define REG_PLUS_RX_COMP1_TAIL 0x422C /* RX completion 2 + tail reg. 4 total. */ +#define REG_PLUS_RX_COMPN_HEAD(x) (REG_PLUS_RX_COMP1_HEAD + 8*((x) - 1)) +#define REG_PLUS_RX_COMPN_TAIL(x) (REG_PLUS_RX_COMP1_TAIL + 8*((x) - 1)) +#define REG_PLUS_RX_AE1_THRESH 0x4240 /* RX almost empty 2 + thresholds */ +#define RX_AE1_THRESH_FREE_MASK RX_AE_THRESH_FREE_MASK +#define RX_AE1_THRESH_FREE_SHIFT RX_AE_THRESH_FREE_SHIFT + +/** header parser registers **/ + +/* RX parser configuration register. + * DEFAULT: 0x1651004 + */ +#define REG_HP_CFG 0x4140 /* header parser + configuration reg */ +#define HP_CFG_PARSE_EN 0x00000001 /* enab header parsing */ +#define HP_CFG_NUM_CPU_MASK 0x000000FC /* # processors + 0 = 64. 0x3f = 63 */ +#define HP_CFG_NUM_CPU_SHIFT 2 +#define HP_CFG_SYN_INC_MASK 0x00000100 /* SYN bit won't increment + TCP seq # by one when + stored in FDBM */ +#define HP_CFG_TCP_THRESH_MASK 0x000FFE00 /* # bytes of TCP data + needed to be considered + for reassembly */ +#define HP_CFG_TCP_THRESH_SHIFT 9 + +/* access to RX Instruction RAM. 5-bit register/counter holds addr + * of 39 bit entry to be read/written. 32 LSB in _DATA_LOW. 7 MSB in _DATA_HI. + * RX_DMA_EN must be 0 for RX instr PIO access. DATA_HI should be last access + * of sequence. + * DEFAULT: undefined + */ +#define REG_HP_INSTR_RAM_ADDR 0x4144 /* HP instruction RAM + address */ +#define HP_INSTR_RAM_ADDR_MASK 0x01F /* 5-bit mask */ +#define REG_HP_INSTR_RAM_DATA_LOW 0x4148 /* HP instruction RAM + data low */ +#define HP_INSTR_RAM_LOW_OUTMASK_MASK 0x0000FFFF +#define HP_INSTR_RAM_LOW_OUTMASK_SHIFT 0 +#define HP_INSTR_RAM_LOW_OUTSHIFT_MASK 0x000F0000 +#define HP_INSTR_RAM_LOW_OUTSHIFT_SHIFT 16 +#define HP_INSTR_RAM_LOW_OUTEN_MASK 0x00300000 +#define HP_INSTR_RAM_LOW_OUTEN_SHIFT 20 +#define HP_INSTR_RAM_LOW_OUTARG_MASK 0xFFC00000 +#define HP_INSTR_RAM_LOW_OUTARG_SHIFT 22 +#define REG_HP_INSTR_RAM_DATA_MID 0x414C /* HP instruction RAM + data mid */ +#define HP_INSTR_RAM_MID_OUTARG_MASK 0x00000003 +#define HP_INSTR_RAM_MID_OUTARG_SHIFT 0 +#define HP_INSTR_RAM_MID_OUTOP_MASK 0x0000003C +#define HP_INSTR_RAM_MID_OUTOP_SHIFT 2 +#define HP_INSTR_RAM_MID_FNEXT_MASK 0x000007C0 +#define HP_INSTR_RAM_MID_FNEXT_SHIFT 6 +#define HP_INSTR_RAM_MID_FOFF_MASK 0x0003F800 +#define HP_INSTR_RAM_MID_FOFF_SHIFT 11 +#define HP_INSTR_RAM_MID_SNEXT_MASK 0x007C0000 +#define HP_INSTR_RAM_MID_SNEXT_SHIFT 18 +#define HP_INSTR_RAM_MID_SOFF_MASK 0x3F800000 +#define HP_INSTR_RAM_MID_SOFF_SHIFT 23 +#define HP_INSTR_RAM_MID_OP_MASK 0xC0000000 +#define HP_INSTR_RAM_MID_OP_SHIFT 30 +#define REG_HP_INSTR_RAM_DATA_HI 0x4150 /* HP instruction RAM + data high */ +#define HP_INSTR_RAM_HI_VAL_MASK 0x0000FFFF +#define HP_INSTR_RAM_HI_VAL_SHIFT 0 +#define HP_INSTR_RAM_HI_MASK_MASK 0xFFFF0000 +#define HP_INSTR_RAM_HI_MASK_SHIFT 16 + +/* PIO access into RX Header parser data RAM and flow database. + * 11-bit register. Data fills the LSB portion of bus if less than 32 bits. + * DATA_RAM: write RAM_FDB_DATA with index to access DATA_RAM. + * RAM bytes = 4*(x - 1) + [3:0]. e.g., 0 -> [3:0], 31 -> [123:120] + * FLOWDB: write DATA_RAM_FDB register and then read/write FDB1-12 to access + * flow database. + * RX_DMA_EN must be 0 for RX parser RAM PIO access. RX Parser RAM data reg + * should be the last write access of the write sequence. + * DEFAULT: undefined + */ +#define REG_HP_DATA_RAM_FDB_ADDR 0x4154 /* HP data and FDB + RAM address */ +#define HP_DATA_RAM_FDB_DATA_MASK 0x001F /* select 1 of 86 byte + locations in header + parser data ram to + read/write */ +#define HP_DATA_RAM_FDB_FDB_MASK 0x3F00 /* 1 of 64 353-bit locations + in the flow database */ +#define REG_HP_DATA_RAM_DATA 0x4158 /* HP data RAM data */ + +/* HP flow database registers: 1 - 12, 0x415C - 0x4188, 4 8-bit bytes + * FLOW_DB(1) = IP_SA[127:96], FLOW_DB(2) = IP_SA[95:64] + * FLOW_DB(3) = IP_SA[63:32], FLOW_DB(4) = IP_SA[31:0] + * FLOW_DB(5) = IP_DA[127:96], FLOW_DB(6) = IP_DA[95:64] + * FLOW_DB(7) = IP_DA[63:32], FLOW_DB(8) = IP_DA[31:0] + * FLOW_DB(9) = {TCP_SP[15:0],TCP_DP[15:0]} + * FLOW_DB(10) = bit 0 has value for flow valid + * FLOW_DB(11) = TCP_SEQ[63:32], FLOW_DB(12) = TCP_SEQ[31:0] + */ +#define REG_HP_FLOW_DB0 0x415C /* HP flow database 1 reg */ +#define REG_HP_FLOW_DBN(x) (REG_HP_FLOW_DB0 + (x)*4) + +/* diagnostics for RX Header Parser block. + * ASUN: the header parser state machine register is used for diagnostics + * purposes. however, the spec doesn't have any details on it. + */ +#define REG_HP_STATE_MACHINE 0x418C /* (ro) HP state machine */ +#define REG_HP_STATUS0 0x4190 /* (ro) HP status 1 */ +#define HP_STATUS0_SAP_MASK 0xFFFF0000 /* SAP */ +#define HP_STATUS0_L3_OFF_MASK 0x0000FE00 /* L3 offset */ +#define HP_STATUS0_LB_CPUNUM_MASK 0x000001F8 /* load balancing CPU + number */ +#define HP_STATUS0_HRP_OPCODE_MASK 0x00000007 /* HRP opcode */ + +#define REG_HP_STATUS1 0x4194 /* (ro) HP status 2 */ +#define HP_STATUS1_ACCUR2_MASK 0xE0000000 /* accu R2[6:4] */ +#define HP_STATUS1_FLOWID_MASK 0x1F800000 /* flow id */ +#define HP_STATUS1_TCP_OFF_MASK 0x007F0000 /* tcp payload offset */ +#define HP_STATUS1_TCP_SIZE_MASK 0x0000FFFF /* tcp payload size */ + +#define REG_HP_STATUS2 0x4198 /* (ro) HP status 3 */ +#define HP_STATUS2_ACCUR2_MASK 0xF0000000 /* accu R2[3:0] */ +#define HP_STATUS2_CSUM_OFF_MASK 0x07F00000 /* checksum start + start offset */ +#define HP_STATUS2_ACCUR1_MASK 0x000FE000 /* accu R1 */ +#define HP_STATUS2_FORCE_DROP 0x00001000 /* force drop */ +#define HP_STATUS2_BWO_REASSM 0x00000800 /* batching w/o + reassembly */ +#define HP_STATUS2_JH_SPLIT_EN 0x00000400 /* jumbo header split + enable */ +#define HP_STATUS2_FORCE_TCP_NOCHECK 0x00000200 /* force tcp no payload + check */ +#define HP_STATUS2_DATA_MASK_ZERO 0x00000100 /* mask of data length + equal to zero */ +#define HP_STATUS2_FORCE_TCP_CHECK 0x00000080 /* force tcp payload + chk */ +#define HP_STATUS2_MASK_TCP_THRESH 0x00000040 /* mask of payload + threshold */ +#define HP_STATUS2_NO_ASSIST 0x00000020 /* no assist */ +#define HP_STATUS2_CTRL_PACKET_FLAG 0x00000010 /* control packet flag */ +#define HP_STATUS2_TCP_FLAG_CHECK 0x00000008 /* tcp flag check */ +#define HP_STATUS2_SYN_FLAG 0x00000004 /* syn flag */ +#define HP_STATUS2_TCP_CHECK 0x00000002 /* tcp payload chk */ +#define HP_STATUS2_TCP_NOCHECK 0x00000001 /* tcp no payload chk */ + +/* BIST for header parser(HP) and flow database memories (FDBM). set _START + * to start BIST. controller clears _START on completion. _START can also + * be cleared to force termination of BIST. a bit set indicates that that + * memory passed its BIST. + */ +#define REG_HP_RAM_BIST 0x419C /* HP RAM BIST reg */ +#define HP_RAM_BIST_HP_DATA_PASS 0x80000000 /* HP data ram */ +#define HP_RAM_BIST_HP_INSTR0_PASS 0x40000000 /* HP instr ram 0 */ +#define HP_RAM_BIST_HP_INSTR1_PASS 0x20000000 /* HP instr ram 1 */ +#define HP_RAM_BIST_HP_INSTR2_PASS 0x10000000 /* HP instr ram 2 */ +#define HP_RAM_BIST_FDBM_AGE0_PASS 0x08000000 /* FDBM aging RAM0 */ +#define HP_RAM_BIST_FDBM_AGE1_PASS 0x04000000 /* FDBM aging RAM1 */ +#define HP_RAM_BIST_FDBM_FLOWID00_PASS 0x02000000 /* FDBM flowid RAM0 + bank 0 */ +#define HP_RAM_BIST_FDBM_FLOWID10_PASS 0x01000000 /* FDBM flowid RAM1 + bank 0 */ +#define HP_RAM_BIST_FDBM_FLOWID20_PASS 0x00800000 /* FDBM flowid RAM2 + bank 0 */ +#define HP_RAM_BIST_FDBM_FLOWID30_PASS 0x00400000 /* FDBM flowid RAM3 + bank 0 */ +#define HP_RAM_BIST_FDBM_FLOWID01_PASS 0x00200000 /* FDBM flowid RAM0 + bank 1 */ +#define HP_RAM_BIST_FDBM_FLOWID11_PASS 0x00100000 /* FDBM flowid RAM1 + bank 2 */ +#define HP_RAM_BIST_FDBM_FLOWID21_PASS 0x00080000 /* FDBM flowid RAM2 + bank 1 */ +#define HP_RAM_BIST_FDBM_FLOWID31_PASS 0x00040000 /* FDBM flowid RAM3 + bank 1 */ +#define HP_RAM_BIST_FDBM_TCPSEQ_PASS 0x00020000 /* FDBM tcp sequence + RAM */ +#define HP_RAM_BIST_SUMMARY 0x00000002 /* all BIST tests */ +#define HP_RAM_BIST_START 0x00000001 /* start/stop BIST */ + + +/** MAC registers. **/ +/* reset bits are set using a PIO write and self-cleared after the command + * execution has completed. + */ +#define REG_MAC_TX_RESET 0x6000 /* TX MAC software reset + command (default: 0x0) */ +#define REG_MAC_RX_RESET 0x6004 /* RX MAC software reset + command (default: 0x0) */ +/* execute a pause flow control frame transmission + DEFAULT: 0x0XXXX */ +#define REG_MAC_SEND_PAUSE 0x6008 /* send pause command reg */ +#define MAC_SEND_PAUSE_TIME_MASK 0x0000FFFF /* value of pause time + to be sent on network + in units of slot + times */ +#define MAC_SEND_PAUSE_SEND 0x00010000 /* send pause flow ctrl + frame on network */ + +/* bit set indicates that event occurred. auto-cleared when status register + * is read and have corresponding mask bits in mask register. events will + * trigger an interrupt if the corresponding mask bit is 0. + * status register default: 0x00000000 + * mask register default = 0xFFFFFFFF on reset + */ +#define REG_MAC_TX_STATUS 0x6010 /* TX MAC status reg */ +#define MAC_TX_FRAME_XMIT 0x0001 /* successful frame + transmision */ +#define MAC_TX_UNDERRUN 0x0002 /* terminated frame + transmission due to + data starvation in the + xmit data path */ +#define MAC_TX_MAX_PACKET_ERR 0x0004 /* frame exceeds max allowed + length passed to TX MAC + by the DMA engine */ +#define MAC_TX_COLL_NORMAL 0x0008 /* rollover of the normal + collision counter */ +#define MAC_TX_COLL_EXCESS 0x0010 /* rollover of the excessive + collision counter */ +#define MAC_TX_COLL_LATE 0x0020 /* rollover of the late + collision counter */ +#define MAC_TX_COLL_FIRST 0x0040 /* rollover of the first + collision counter */ +#define MAC_TX_DEFER_TIMER 0x0080 /* rollover of the defer + timer */ +#define MAC_TX_PEAK_ATTEMPTS 0x0100 /* rollover of the peak + attempts counter */ + +#define REG_MAC_RX_STATUS 0x6014 /* RX MAC status reg */ +#define MAC_RX_FRAME_RECV 0x0001 /* successful receipt of + a frame */ +#define MAC_RX_OVERFLOW 0x0002 /* dropped frame due to + RX FIFO overflow */ +#define MAC_RX_FRAME_COUNT 0x0004 /* rollover of receive frame + counter */ +#define MAC_RX_ALIGN_ERR 0x0008 /* rollover of alignment + error counter */ +#define MAC_RX_CRC_ERR 0x0010 /* rollover of crc error + counter */ +#define MAC_RX_LEN_ERR 0x0020 /* rollover of length + error counter */ +#define MAC_RX_VIOL_ERR 0x0040 /* rollover of code + violation error */ + +/* DEFAULT: 0xXXXX0000 on reset */ +#define REG_MAC_CTRL_STATUS 0x6018 /* MAC control status reg */ +#define MAC_CTRL_PAUSE_RECEIVED 0x00000001 /* successful + reception of a + pause control + frame */ +#define MAC_CTRL_PAUSE_STATE 0x00000002 /* MAC has made a + transition from + "not paused" to + "paused" */ +#define MAC_CTRL_NOPAUSE_STATE 0x00000004 /* MAC has made a + transition from + "paused" to "not + paused" */ +#define MAC_CTRL_PAUSE_TIME_MASK 0xFFFF0000 /* value of pause time + operand that was + received in the last + pause flow control + frame */ + +/* layout identical to TX MAC[8:0] */ +#define REG_MAC_TX_MASK 0x6020 /* TX MAC mask reg */ +/* layout identical to RX MAC[6:0] */ +#define REG_MAC_RX_MASK 0x6024 /* RX MAC mask reg */ +/* layout identical to CTRL MAC[2:0] */ +#define REG_MAC_CTRL_MASK 0x6028 /* MAC control mask reg */ + +/* to ensure proper operation, CFG_EN must be cleared to 0 and a delay + * imposed before writes to other bits in the TX_MAC_CFG register or any of + * the MAC parameters is performed. delay dependent upon time required to + * transmit a maximum size frame (= MAC_FRAMESIZE_MAX*8/Mbps). e.g., + * the delay for a 1518-byte frame on a 100Mbps network is 125us. + * alternatively, just poll TX_CFG_EN until it reads back as 0. + * NOTE: on half-duplex 1Gbps, TX_CFG_CARRIER_EXTEND and + * RX_CFG_CARRIER_EXTEND should be set and the SLOT_TIME register should + * be 0x200 (slot time of 512 bytes) + */ +#define REG_MAC_TX_CFG 0x6030 /* TX MAC config reg */ +#define MAC_TX_CFG_EN 0x0001 /* enable TX MAC. 0 will + force TXMAC state + machine to remain in + idle state or to + transition to idle state + on completion of an + ongoing packet. */ +#define MAC_TX_CFG_IGNORE_CARRIER 0x0002 /* disable CSMA/CD deferral + process. set to 1 when + full duplex and 0 when + half duplex */ +#define MAC_TX_CFG_IGNORE_COLL 0x0004 /* disable CSMA/CD backoff + algorithm. set to 1 when + full duplex and 0 when + half duplex */ +#define MAC_TX_CFG_IPG_EN 0x0008 /* enable extension of the + Rx-to-TX IPG. after + receiving a frame, TX + MAC will reset its + deferral process to + carrier sense for the + amount of time = IPG0 + + IPG1 and commit to + transmission for time + specified in IPG2. when + 0 or when xmitting frames + back-to-pack (Tx-to-Tx + IPG), TX MAC ignores + IPG0 and will only use + IPG1 for deferral time. + IPG2 still used. */ +#define MAC_TX_CFG_NEVER_GIVE_UP_EN 0x0010 /* TX MAC will not easily + give up on frame + xmission. if backoff + algorithm reaches the + ATTEMPT_LIMIT, it will + clear attempts counter + and continue trying to + send the frame as + specified by + GIVE_UP_LIM. when 0, + TX MAC will execute + standard CSMA/CD prot. */ +#define MAC_TX_CFG_NEVER_GIVE_UP_LIM 0x0020 /* when set, TX MAC will + continue to try to xmit + until successful. when + 0, TX MAC will continue + to try xmitting until + successful or backoff + algorithm reaches + ATTEMPT_LIMIT*16 */ +#define MAC_TX_CFG_NO_BACKOFF 0x0040 /* modify CSMA/CD to disable + backoff algorithm. TX + MAC will not back off + after a xmission attempt + that resulted in a + collision. */ +#define MAC_TX_CFG_SLOW_DOWN 0x0080 /* modify CSMA/CD so that + deferral process is reset + in response to carrier + sense during the entire + duration of IPG. TX MAC + will only commit to frame + xmission after frame + xmission has actually + begun. */ +#define MAC_TX_CFG_NO_FCS 0x0100 /* TX MAC will not generate + CRC for all xmitted + packets. when clear, CRC + generation is dependent + upon NO_CRC bit in the + xmit control word from + TX DMA */ +#define MAC_TX_CFG_CARRIER_EXTEND 0x0200 /* enables xmit part of the + carrier extension + feature. this allows for + longer collision domains + by extending the carrier + and collision window + from the end of FCS until + the end of the slot time + if necessary. Required + for half-duplex at 1Gbps, + clear otherwise. */ + +/* when CRC is not stripped, reassembly packets will not contain the CRC. + * these will be stripped by HRP because it reassembles layer 4 data, and the + * CRC is layer 2. however, non-reassembly packets will still contain the CRC + * when passed to the host. to ensure proper operation, need to wait 3.2ms + * after clearing RX_CFG_EN before writing to any other RX MAC registers + * or other MAC parameters. alternatively, poll RX_CFG_EN until it clears + * to 0. similary, HASH_FILTER_EN and ADDR_FILTER_EN have the same + * restrictions as CFG_EN. + */ +#define REG_MAC_RX_CFG 0x6034 /* RX MAC config reg */ +#define MAC_RX_CFG_EN 0x0001 /* enable RX MAC */ +#define MAC_RX_CFG_STRIP_PAD 0x0002 /* always program to 0. + feature not supported */ +#define MAC_RX_CFG_STRIP_FCS 0x0004 /* RX MAC will strip the + last 4 bytes of a + received frame. */ +#define MAC_RX_CFG_PROMISC_EN 0x0008 /* promiscuous mode */ +#define MAC_RX_CFG_PROMISC_GROUP_EN 0x0010 /* accept all valid + multicast frames (group + bit in DA field set) */ +#define MAC_RX_CFG_HASH_FILTER_EN 0x0020 /* use hash table to filter + multicast addresses */ +#define MAC_RX_CFG_ADDR_FILTER_EN 0x0040 /* cause RX MAC to use + address filtering regs + to filter both unicast + and multicast + addresses */ +#define MAC_RX_CFG_DISABLE_DISCARD 0x0080 /* pass errored frames to + RX DMA by setting BAD + bit but not Abort bit + in the status. CRC, + framing, and length errs + will not increment + error counters. frames + which don't match dest + addr will be passed up + w/ BAD bit set. */ +#define MAC_RX_CFG_CARRIER_EXTEND 0x0100 /* enable reception of + packet bursts generated + by carrier extension + with packet bursting + senders. only applies + to half-duplex 1Gbps */ + +/* DEFAULT: 0x0 */ +#define REG_MAC_CTRL_CFG 0x6038 /* MAC control config reg */ +#define MAC_CTRL_CFG_SEND_PAUSE_EN 0x0001 /* respond to requests for + sending pause flow ctrl + frames */ +#define MAC_CTRL_CFG_RECV_PAUSE_EN 0x0002 /* respond to received + pause flow ctrl frames */ +#define MAC_CTRL_CFG_PASS_CTRL 0x0004 /* pass valid MAC ctrl + packets to RX DMA */ + +/* to ensure proper operation, a global initialization sequence should be + * performed when a loopback config is entered or exited. if programmed after + * a hw or global sw reset, RX/TX MAC software reset and initialization + * should be done to ensure stable clocking. + * DEFAULT: 0x0 + */ +#define REG_MAC_XIF_CFG 0x603C /* XIF config reg */ +#define MAC_XIF_TX_MII_OUTPUT_EN 0x0001 /* enable output drivers + on MII xmit bus */ +#define MAC_XIF_MII_INT_LOOPBACK 0x0002 /* loopback GMII xmit data + path to GMII recv data + path. phy mode register + clock selection must be + set to GMII mode and + GMII_MODE should be set + to 1. in loopback mode, + REFCLK will drive the + entire mac core. 0 for + normal operation. */ +#define MAC_XIF_DISABLE_ECHO 0x0004 /* disables receive data + path during packet + xmission. clear to 0 + in any full duplex mode, + in any loopback mode, + or in half-duplex SERDES + or SLINK modes. set when + in half-duplex when + using external phy. */ +#define MAC_XIF_GMII_MODE 0x0008 /* MAC operates with GMII + clocks and datapath */ +#define MAC_XIF_MII_BUFFER_OUTPUT_EN 0x0010 /* MII_BUF_EN pin. enable + external tristate buffer + on the MII receive + bus. */ +#define MAC_XIF_LINK_LED 0x0020 /* LINKLED# active (low) */ +#define MAC_XIF_FDPLX_LED 0x0040 /* FDPLXLED# active (low) */ + +#define REG_MAC_IPG0 0x6040 /* inter-packet gap0 reg. + recommended: 0x00 */ +#define REG_MAC_IPG1 0x6044 /* inter-packet gap1 reg + recommended: 0x08 */ +#define REG_MAC_IPG2 0x6048 /* inter-packet gap2 reg + recommended: 0x04 */ +#define REG_MAC_SLOT_TIME 0x604C /* slot time reg + recommended: 0x40 */ +#define REG_MAC_FRAMESIZE_MIN 0x6050 /* min frame size reg + recommended: 0x40 */ + +/* FRAMESIZE_MAX holds both the max frame size as well as the max burst size. + * recommended value: 0x2000.05EE + */ +#define REG_MAC_FRAMESIZE_MAX 0x6054 /* max frame size reg */ +#define MAC_FRAMESIZE_MAX_BURST_MASK 0x3FFF0000 /* max burst size */ +#define MAC_FRAMESIZE_MAX_BURST_SHIFT 16 +#define MAC_FRAMESIZE_MAX_FRAME_MASK 0x00007FFF /* max frame size */ +#define MAC_FRAMESIZE_MAX_FRAME_SHIFT 0 +#define REG_MAC_PA_SIZE 0x6058 /* PA size reg. number of + preamble bytes that the + TX MAC will xmit at the + beginning of each frame + value should be 2 or + greater. recommended + value: 0x07 */ +#define REG_MAC_JAM_SIZE 0x605C /* jam size reg. duration + of jam in units of media + byte time. recommended + value: 0x04 */ +#define REG_MAC_ATTEMPT_LIMIT 0x6060 /* attempt limit reg. # + of attempts TX MAC will + make to xmit a frame + before it resets its + attempts counter. after + the limit has been + reached, TX MAC may or + may not drop the frame + dependent upon value + in TX_MAC_CFG. + recommended + value: 0x10 */ +#define REG_MAC_CTRL_TYPE 0x6064 /* MAC control type reg. + type field of a MAC + ctrl frame. recommended + value: 0x8808 */ + +/* mac address registers: 0 - 44, 0x6080 - 0x6130, 4 8-bit bytes. + * register contains comparison + * 0 16 MSB of primary MAC addr [47:32] of DA field + * 1 16 middle bits "" [31:16] of DA field + * 2 16 LSB "" [15:0] of DA field + * 3*x 16MSB of alt MAC addr 1-15 [47:32] of DA field + * 4*x 16 middle bits "" [31:16] + * 5*x 16 LSB "" [15:0] + * 42 16 MSB of MAC CTRL addr [47:32] of DA. + * 43 16 middle bits "" [31:16] + * 44 16 LSB "" [15:0] + * MAC CTRL addr must be the reserved multicast addr for MAC CTRL frames. + * if there is a match, MAC will set the bit for alternative address + * filter pass [15] + + * here is the map of registers given MAC address notation: a:b:c:d:e:f + * ab cd ef + * primary addr reg 2 reg 1 reg 0 + * alt addr 1 reg 5 reg 4 reg 3 + * alt addr x reg 5*x reg 4*x reg 3*x + * ctrl addr reg 44 reg 43 reg 42 + */ +#define REG_MAC_ADDR0 0x6080 /* MAC address 0 reg */ +#define REG_MAC_ADDRN(x) (REG_MAC_ADDR0 + (x)*4) +#define REG_MAC_ADDR_FILTER0 0x614C /* address filter 0 reg + [47:32] */ +#define REG_MAC_ADDR_FILTER1 0x6150 /* address filter 1 reg + [31:16] */ +#define REG_MAC_ADDR_FILTER2 0x6154 /* address filter 2 reg + [15:0] */ +#define REG_MAC_ADDR_FILTER2_1_MASK 0x6158 /* address filter 2 and 1 + mask reg. 8-bit reg + contains nibble mask for + reg 2 and 1. */ +#define REG_MAC_ADDR_FILTER0_MASK 0x615C /* address filter 0 mask + reg */ + +/* hash table registers: 0 - 15, 0x6160 - 0x619C, 4 8-bit bytes + * 16-bit registers contain bits of the hash table. + * reg x -> [16*(15 - x) + 15 : 16*(15 - x)]. + * e.g., 15 -> [15:0], 0 -> [255:240] + */ +#define REG_MAC_HASH_TABLE0 0x6160 /* hash table 0 reg */ +#define REG_MAC_HASH_TABLEN(x) (REG_MAC_HASH_TABLE0 + (x)*4) + +/* statistics registers. these registers generate an interrupt on + * overflow. recommended initialization: 0x0000. most are 16-bits except + * for PEAK_ATTEMPTS register which is 8 bits. + */ +#define REG_MAC_COLL_NORMAL 0x61A0 /* normal collision + counter. */ +#define REG_MAC_COLL_FIRST 0x61A4 /* first attempt + successful collision + counter */ +#define REG_MAC_COLL_EXCESS 0x61A8 /* excessive collision + counter */ +#define REG_MAC_COLL_LATE 0x61AC /* late collision counter */ +#define REG_MAC_TIMER_DEFER 0x61B0 /* defer timer. time base + is the media byte + clock/256 */ +#define REG_MAC_ATTEMPTS_PEAK 0x61B4 /* peak attempts reg */ +#define REG_MAC_RECV_FRAME 0x61B8 /* receive frame counter */ +#define REG_MAC_LEN_ERR 0x61BC /* length error counter */ +#define REG_MAC_ALIGN_ERR 0x61C0 /* alignment error counter */ +#define REG_MAC_FCS_ERR 0x61C4 /* FCS error counter */ +#define REG_MAC_RX_CODE_ERR 0x61C8 /* RX code violation + error counter */ + +/* misc registers */ +#define REG_MAC_RANDOM_SEED 0x61CC /* random number seed reg. + 10-bit register used as a + seed for the random number + generator for the CSMA/CD + backoff algorithm. only + programmed after power-on + reset and should be a + random value which has a + high likelihood of being + unique for each MAC + attached to a network + segment (e.g., 10 LSB of + MAC address) */ + +/* ASUN: there's a PAUSE_TIMER (ro) described, but it's not in the address + * map + */ + +/* 27-bit register has the current state for key state machines in the MAC */ +#define REG_MAC_STATE_MACHINE 0x61D0 /* (ro) state machine reg */ +#define MAC_SM_RLM_MASK 0x07800000 +#define MAC_SM_RLM_SHIFT 23 +#define MAC_SM_RX_FC_MASK 0x00700000 +#define MAC_SM_RX_FC_SHIFT 20 +#define MAC_SM_TLM_MASK 0x000F0000 +#define MAC_SM_TLM_SHIFT 16 +#define MAC_SM_ENCAP_SM_MASK 0x0000F000 +#define MAC_SM_ENCAP_SM_SHIFT 12 +#define MAC_SM_TX_REQ_MASK 0x00000C00 +#define MAC_SM_TX_REQ_SHIFT 10 +#define MAC_SM_TX_FC_MASK 0x000003C0 +#define MAC_SM_TX_FC_SHIFT 6 +#define MAC_SM_FIFO_WRITE_SEL_MASK 0x00000038 +#define MAC_SM_FIFO_WRITE_SEL_SHIFT 3 +#define MAC_SM_TX_FIFO_EMPTY_MASK 0x00000007 +#define MAC_SM_TX_FIFO_EMPTY_SHIFT 0 + +/** MIF registers. the MIF can be programmed in either bit-bang or + * frame mode. + **/ +#define REG_MIF_BIT_BANG_CLOCK 0x6200 /* MIF bit-bang clock. + 1 -> 0 will generate a + rising edge. 0 -> 1 will + generate a falling edge. */ +#define REG_MIF_BIT_BANG_DATA 0x6204 /* MIF bit-bang data. 1-bit + register generates data */ +#define REG_MIF_BIT_BANG_OUTPUT_EN 0x6208 /* MIF bit-bang output + enable. enable when + xmitting data from MIF to + transceiver. */ + +/* 32-bit register serves as an instruction register when the MIF is + * programmed in frame mode. load this register w/ a valid instruction + * (as per IEEE 802.3u MII spec). poll this register to check for instruction + * execution completion. during a read operation, this register will also + * contain the 16-bit data returned by the tranceiver. unless specified + * otherwise, fields are considered "don't care" when polling for + * completion. + */ +#define REG_MIF_FRAME 0x620C /* MIF frame/output reg */ +#define MIF_FRAME_START_MASK 0xC0000000 /* start of frame. + load w/ 01 when + issuing an instr */ +#define MIF_FRAME_ST 0x40000000 /* STart of frame */ +#define MIF_FRAME_OPCODE_MASK 0x30000000 /* opcode. 01 for a + write. 10 for a + read */ +#define MIF_FRAME_OP_READ 0x20000000 /* read OPcode */ +#define MIF_FRAME_OP_WRITE 0x10000000 /* write OPcode */ +#define MIF_FRAME_PHY_ADDR_MASK 0x0F800000 /* phy address. when + issuing an instr, + this field should be + loaded w/ the XCVR + addr */ +#define MIF_FRAME_PHY_ADDR_SHIFT 23 +#define MIF_FRAME_REG_ADDR_MASK 0x007C0000 /* register address. + when issuing an instr, + addr of register + to be read/written */ +#define MIF_FRAME_REG_ADDR_SHIFT 18 +#define MIF_FRAME_TURN_AROUND_MSB 0x00020000 /* turn around, MSB. + when issuing an instr, + set this bit to 1 */ +#define MIF_FRAME_TURN_AROUND_LSB 0x00010000 /* turn around, LSB. + when issuing an instr, + set this bit to 0. + when polling for + completion, 1 means + that instr execution + has been completed */ +#define MIF_FRAME_DATA_MASK 0x0000FFFF /* instruction payload + load with 16-bit data + to be written in + transceiver reg for a + write. doesn't matter + in a read. when + polling for + completion, field is + "don't care" for write + and 16-bit data + returned by the + transceiver for a + read (if valid bit + is set) */ +#define REG_MIF_CFG 0x6210 /* MIF config reg */ +#define MIF_CFG_PHY_SELECT 0x0001 /* 1 -> select MDIO_1 + 0 -> select MDIO_0 */ +#define MIF_CFG_POLL_EN 0x0002 /* enable polling + mechanism. if set, + BB_MODE should be 0 */ +#define MIF_CFG_BB_MODE 0x0004 /* 1 -> bit-bang mode + 0 -> frame mode */ +#define MIF_CFG_POLL_REG_MASK 0x00F8 /* register address to be + used by polling mode. + only meaningful if POLL_EN + is set to 1 */ +#define MIF_CFG_POLL_REG_SHIFT 3 +#define MIF_CFG_MDIO_0 0x0100 /* (ro) dual purpose. + when MDIO_0 is idle, + 1 -> tranceiver is + connected to MDIO_0. + when MIF is communicating + w/ MDIO_0 in bit-bang + mode, this bit indicates + the incoming bit stream + during a read op */ +#define MIF_CFG_MDIO_1 0x0200 /* (ro) dual purpose. + when MDIO_1 is idle, + 1 -> transceiver is + connected to MDIO_1. + when MIF is communicating + w/ MDIO_1 in bit-bang + mode, this bit indicates + the incoming bit stream + during a read op */ +#define MIF_CFG_POLL_PHY_MASK 0x7C00 /* tranceiver address to + be polled */ +#define MIF_CFG_POLL_PHY_SHIFT 10 + +/* 16-bit register used to determine which bits in the POLL_STATUS portion of + * the MIF_STATUS register will cause an interrupt. if a mask bit is 0, + * corresponding bit of the POLL_STATUS will generate a MIF interrupt when + * set. DEFAULT: 0xFFFF + */ +#define REG_MIF_MASK 0x6214 /* MIF mask reg */ + +/* 32-bit register used when in poll mode. auto-cleared after being read */ +#define REG_MIF_STATUS 0x6218 /* MIF status reg */ +#define MIF_STATUS_POLL_DATA_MASK 0xFFFF0000 /* poll data contains + the "latest image" + update of the XCVR + reg being read */ +#define MIF_STATUS_POLL_DATA_SHIFT 16 +#define MIF_STATUS_POLL_STATUS_MASK 0x0000FFFF /* poll status indicates + which bits in the + POLL_DATA field have + changed since the + MIF_STATUS reg was + last read */ +#define MIF_STATUS_POLL_STATUS_SHIFT 0 + +/* 7-bit register has current state for all state machines in the MIF */ +#define REG_MIF_STATE_MACHINE 0x621C /* MIF state machine reg */ +#define MIF_SM_CONTROL_MASK 0x07 /* control state machine + state */ +#define MIF_SM_EXECUTION_MASK 0x60 /* execution state machine + state */ + +/** PCS/Serialink. the following registers are equivalent to the standard + * MII management registers except that they're directly mapped in + * Cassini's register space. + **/ + +/* the auto-negotiation enable bit should be programmed the same at + * the link partner as in the local device to enable auto-negotiation to + * complete. when that bit is reprogrammed, auto-neg/manual config is + * restarted automatically. + * DEFAULT: 0x1040 + */ +#define REG_PCS_MII_CTRL 0x9000 /* PCS MII control reg */ +#define PCS_MII_CTRL_1000_SEL 0x0040 /* reads 1. ignored on + writes */ +#define PCS_MII_CTRL_COLLISION_TEST 0x0080 /* COL signal at the PCS + to MAC interface is + activated regardless + of activity */ +#define PCS_MII_CTRL_DUPLEX 0x0100 /* forced 0x0. PCS + behaviour same for + half and full dplx */ +#define PCS_MII_RESTART_AUTONEG 0x0200 /* self clearing. + restart auto- + negotiation */ +#define PCS_MII_ISOLATE 0x0400 /* read as 0. ignored + on writes */ +#define PCS_MII_POWER_DOWN 0x0800 /* read as 0. ignored + on writes */ +#define PCS_MII_AUTONEG_EN 0x1000 /* default 1. PCS goes + through automatic + link config before it + can be used. when 0, + link can be used + w/out any link config + phase */ +#define PCS_MII_10_100_SEL 0x2000 /* read as 0. ignored on + writes */ +#define PCS_MII_RESET 0x8000 /* reset PCS. self-clears + when done */ + +/* DEFAULT: 0x0108 */ +#define REG_PCS_MII_STATUS 0x9004 /* PCS MII status reg */ +#define PCS_MII_STATUS_EXTEND_CAP 0x0001 /* reads 0 */ +#define PCS_MII_STATUS_JABBER_DETECT 0x0002 /* reads 0 */ +#define PCS_MII_STATUS_LINK_STATUS 0x0004 /* 1 -> link up. + 0 -> link down. 0 is + latched so that 0 is + kept until read. read + 2x to determine if the + link has gone up again */ +#define PCS_MII_STATUS_AUTONEG_ABLE 0x0008 /* reads 1 (able to perform + auto-neg) */ +#define PCS_MII_STATUS_REMOTE_FAULT 0x0010 /* 1 -> remote fault detected + from received link code + word. only valid after + auto-neg completed */ +#define PCS_MII_STATUS_AUTONEG_COMP 0x0020 /* 1 -> auto-negotiation + completed + 0 -> auto-negotiation not + completed */ +#define PCS_MII_STATUS_EXTEND_STATUS 0x0100 /* reads as 1. used as an + indication that this is + a 1000 Base-X PHY. writes + to it are ignored */ + +/* used during auto-negotiation. + * DEFAULT: 0x00E0 + */ +#define REG_PCS_MII_ADVERT 0x9008 /* PCS MII advertisement + reg */ +#define PCS_MII_ADVERT_FD 0x0020 /* advertise full duplex + 1000 Base-X */ +#define PCS_MII_ADVERT_HD 0x0040 /* advertise half-duplex + 1000 Base-X */ +#define PCS_MII_ADVERT_SYM_PAUSE 0x0080 /* advertise PAUSE + symmetric capability */ +#define PCS_MII_ADVERT_ASYM_PAUSE 0x0100 /* advertises PAUSE + asymmetric capability */ +#define PCS_MII_ADVERT_RF_MASK 0x3000 /* remote fault. write bit13 + to optionally indicate to + link partner that chip is + going off-line. bit12 will + get set when signal + detect == FAIL and will + remain set until + successful negotiation */ +#define PCS_MII_ADVERT_ACK 0x4000 /* (ro) */ +#define PCS_MII_ADVERT_NEXT_PAGE 0x8000 /* (ro) forced 0x0 */ + +/* contents updated as a result of autonegotiation. layout and definitions + * identical to PCS_MII_ADVERT + */ +#define REG_PCS_MII_LPA 0x900C /* PCS MII link partner + ability reg */ +#define PCS_MII_LPA_FD PCS_MII_ADVERT_FD +#define PCS_MII_LPA_HD PCS_MII_ADVERT_HD +#define PCS_MII_LPA_SYM_PAUSE PCS_MII_ADVERT_SYM_PAUSE +#define PCS_MII_LPA_ASYM_PAUSE PCS_MII_ADVERT_ASYM_PAUSE +#define PCS_MII_LPA_RF_MASK PCS_MII_ADVERT_RF_MASK +#define PCS_MII_LPA_ACK PCS_MII_ADVERT_ACK +#define PCS_MII_LPA_NEXT_PAGE PCS_MII_ADVERT_NEXT_PAGE + +/* DEFAULT: 0x0 */ +#define REG_PCS_CFG 0x9010 /* PCS config reg */ +#define PCS_CFG_EN 0x01 /* enable PCS. must be + 0 when modifying + PCS_MII_ADVERT */ +#define PCS_CFG_SD_OVERRIDE 0x02 /* sets signal detect to + OK. bit is + non-resettable */ +#define PCS_CFG_SD_ACTIVE_LOW 0x04 /* changes interpretation + of optical signal to make + signal detect okay when + signal is low */ +#define PCS_CFG_JITTER_STUDY_MASK 0x18 /* used to make jitter + measurements. a single + code group is xmitted + regularly. + 0x0 = normal operation + 0x1 = high freq test + pattern, D21.5 + 0x2 = low freq test + pattern, K28.7 + 0x3 = reserved */ +#define PCS_CFG_10MS_TIMER_OVERRIDE 0x20 /* shortens 10-20ms auto- + negotiation timer to + a few cycles for test + purposes */ + +/* used for diagnostic purposes. bits 20-22 autoclear on read */ +#define REG_PCS_STATE_MACHINE 0x9014 /* (ro) PCS state machine + and diagnostic reg */ +#define PCS_SM_TX_STATE_MASK 0x0000000F /* 0 and 1 indicate + xmission of idle. + otherwise, xmission of + a packet */ +#define PCS_SM_RX_STATE_MASK 0x000000F0 /* 0 indicates reception + of idle. otherwise, + reception of packet */ +#define PCS_SM_WORD_SYNC_STATE_MASK 0x00000700 /* 0 indicates loss of + sync */ +#define PCS_SM_SEQ_DETECT_STATE_MASK 0x00001800 /* cycling through 0-3 + indicates reception of + Config codes. cycling + through 0-1 indicates + reception of idles */ +#define PCS_SM_LINK_STATE_MASK 0x0001E000 +#define SM_LINK_STATE_UP 0x00016000 /* link state is up */ + +#define PCS_SM_LOSS_LINK_C 0x00100000 /* loss of link due to + recept of Config + codes */ +#define PCS_SM_LOSS_LINK_SYNC 0x00200000 /* loss of link due to + loss of sync */ +#define PCS_SM_LOSS_SIGNAL_DETECT 0x00400000 /* signal detect goes + from OK to FAIL. bit29 + will also be set if + this is set */ +#define PCS_SM_NO_LINK_BREAKLINK 0x01000000 /* link not up due to + receipt of breaklink + C codes from partner. + C codes w/ 0 content + received triggering + start/restart of + autonegotiation. + should be sent for + no longer than 20ms */ +#define PCS_SM_NO_LINK_SERDES 0x02000000 /* serdes being + initialized. see serdes + state reg */ +#define PCS_SM_NO_LINK_C 0x04000000 /* C codes not stable or + not received */ +#define PCS_SM_NO_LINK_SYNC 0x08000000 /* word sync not + achieved */ +#define PCS_SM_NO_LINK_WAIT_C 0x10000000 /* waiting for C codes + w/ ack bit set */ +#define PCS_SM_NO_LINK_NO_IDLE 0x20000000 /* link partner continues + to send C codes + instead of idle + symbols or pkt data */ + +/* this register indicates interrupt changes in specific PCS MII status bits. + * PCS_INT may be masked at the ISR level. only a single bit is implemented + * for link status change. + */ +#define REG_PCS_INTR_STATUS 0x9018 /* PCS interrupt status */ +#define PCS_INTR_STATUS_LINK_CHANGE 0x04 /* link status has changed + since last read */ + +/* control which network interface is used. no more than one bit should + * be set. + * DEFAULT: none + */ +#define REG_PCS_DATAPATH_MODE 0x9050 /* datapath mode reg */ +#define PCS_DATAPATH_MODE_MII 0x00 /* PCS is not used and + MII/GMII is selected. + selection between MII and + GMII is controlled by + XIF_CFG */ +#define PCS_DATAPATH_MODE_SERDES 0x02 /* PCS is used via the + 10-bit interface */ + +/* input to serdes chip or serialink block */ +#define REG_PCS_SERDES_CTRL 0x9054 /* serdes control reg */ +#define PCS_SERDES_CTRL_LOOPBACK 0x01 /* enable loopback on + serdes interface */ +#define PCS_SERDES_CTRL_SYNCD_EN 0x02 /* enable sync carrier + detection. should be + 0x0 for normal + operation */ +#define PCS_SERDES_CTRL_LOCKREF 0x04 /* frequency-lock RBC[0:1] + to REFCLK when set. + when clear, receiver + clock locks to incoming + serial data */ + +/* multiplex test outputs into the PROM address (PA_3 through PA_0) pins. + * should be 0x0 for normal operations. + * 0b000 normal operation, PROM address[3:0] selected + * 0b001 rxdma req, rxdma ack, rxdma ready, rxdma read + * 0b010 rxmac req, rx ack, rx tag, rx clk shared + * 0b011 txmac req, tx ack, tx tag, tx retry req + * 0b100 tx tp3, tx tp2, tx tp1, tx tp0 + * 0b101 R period RX, R period TX, R period HP, R period BIM + * DEFAULT: 0x0 + */ +#define REG_PCS_SHARED_OUTPUT_SEL 0x9058 /* shared output select */ +#define PCS_SOS_PROM_ADDR_MASK 0x0007 + +/* used for diagnostics. this register indicates progress of the SERDES + * boot up. + * 0b00 undergoing reset + * 0b01 waiting 500us while lockrefn is asserted + * 0b10 waiting for comma detect + * 0b11 receive data is synchronized + * DEFAULT: 0x0 + */ +#define REG_PCS_SERDES_STATE 0x905C /* (ro) serdes state */ +#define PCS_SERDES_STATE_MASK 0x03 + +/* used for diagnostics. indicates number of packets transmitted or received. + * counters rollover w/out generating an interrupt. + * DEFAULT: 0x0 + */ +#define REG_PCS_PACKET_COUNT 0x9060 /* (ro) PCS packet counter */ +#define PCS_PACKET_COUNT_TX 0x000007FF /* pkts xmitted by PCS */ +#define PCS_PACKET_COUNT_RX 0x07FF0000 /* pkts recvd by PCS + whether they + encountered an error + or not */ + +/** LocalBus Devices. the following provides run-time access to the + * Cassini's PROM + ***/ +#define REG_EXPANSION_ROM_RUN_START 0x100000 /* expansion rom run time + access */ +#define REG_EXPANSION_ROM_RUN_END 0x17FFFF + +#define REG_SECOND_LOCALBUS_START 0x180000 /* secondary local bus + device */ +#define REG_SECOND_LOCALBUS_END 0x1FFFFF + +/* entropy device */ +#define REG_ENTROPY_START REG_SECOND_LOCALBUS_START +#define REG_ENTROPY_DATA (REG_ENTROPY_START + 0x00) +#define REG_ENTROPY_STATUS (REG_ENTROPY_START + 0x04) +#define ENTROPY_STATUS_DRDY 0x01 +#define ENTROPY_STATUS_BUSY 0x02 +#define ENTROPY_STATUS_CIPHER 0x04 +#define ENTROPY_STATUS_BYPASS_MASK 0x18 +#define REG_ENTROPY_MODE (REG_ENTROPY_START + 0x05) +#define ENTROPY_MODE_KEY_MASK 0x07 +#define ENTROPY_MODE_ENCRYPT 0x40 +#define REG_ENTROPY_RAND_REG (REG_ENTROPY_START + 0x06) +#define REG_ENTROPY_RESET (REG_ENTROPY_START + 0x07) +#define ENTROPY_RESET_DES_IO 0x01 +#define ENTROPY_RESET_STC_MODE 0x02 +#define ENTROPY_RESET_KEY_CACHE 0x04 +#define ENTROPY_RESET_IV 0x08 +#define REG_ENTROPY_IV (REG_ENTROPY_START + 0x08) +#define REG_ENTROPY_KEY0 (REG_ENTROPY_START + 0x10) +#define REG_ENTROPY_KEYN(x) (REG_ENTROPY_KEY0 + 4*(x)) + +/* phys of interest w/ their special mii registers */ +#define PHY_LUCENT_B0 0x00437421 +#define LUCENT_MII_REG 0x1F + +#define PHY_NS_DP83065 0x20005c78 +#define DP83065_MII_MEM 0x16 +#define DP83065_MII_REGD 0x1D +#define DP83065_MII_REGE 0x1E + +#define PHY_BROADCOM_5411 0x00206071 +#define PHY_BROADCOM_B0 0x00206050 +#define BROADCOM_MII_REG4 0x14 +#define BROADCOM_MII_REG5 0x15 +#define BROADCOM_MII_REG7 0x17 +#define BROADCOM_MII_REG8 0x18 + +#define CAS_MII_ANNPTR 0x07 +#define CAS_MII_ANNPRR 0x08 +#define CAS_MII_1000_CTRL 0x09 +#define CAS_MII_1000_STATUS 0x0A +#define CAS_MII_1000_EXTEND 0x0F + +#define CAS_BMSR_1000_EXTEND 0x0100 /* supports 1000Base-T extended status */ +/* + * if autoneg is disabled, here's the table: + * BMCR_SPEED100 = 100Mbps + * BMCR_SPEED1000 = 1000Mbps + * ~(BMCR_SPEED100 | BMCR_SPEED1000) = 10Mbps + */ +#define CAS_BMCR_SPEED1000 0x0040 /* Select 1000Mbps */ + +#define CAS_ADVERTISE_1000HALF 0x0100 +#define CAS_ADVERTISE_1000FULL 0x0200 +#define CAS_ADVERTISE_PAUSE 0x0400 +#define CAS_ADVERTISE_ASYM_PAUSE 0x0800 + +/* regular lpa register */ +#define CAS_LPA_PAUSE CAS_ADVERTISE_PAUSE +#define CAS_LPA_ASYM_PAUSE CAS_ADVERTISE_ASYM_PAUSE + +/* 1000_STATUS register */ +#define CAS_LPA_1000HALF 0x0400 +#define CAS_LPA_1000FULL 0x0800 + +#define CAS_EXTEND_1000XFULL 0x8000 +#define CAS_EXTEND_1000XHALF 0x4000 +#define CAS_EXTEND_1000TFULL 0x2000 +#define CAS_EXTEND_1000THALF 0x1000 + +/* cassini header parser firmware */ +typedef struct cas_hp_inst { + const char *note; + + u16 mask, val; + + u8 op; + u8 soff, snext; /* if match succeeds, new offset and match */ + u8 foff, fnext; /* if match fails, new offset and match */ + /* output info */ + u8 outop; /* output opcode */ + + u16 outarg; /* output argument */ + u8 outenab; /* output enable: 0 = not, 1 = if match + 2 = if !match, 3 = always */ + u8 outshift; /* barrel shift right, 4 bits */ + u16 outmask; +} cas_hp_inst_t; + +/* comparison */ +#define OP_EQ 0 /* packet == value */ +#define OP_LT 1 /* packet < value */ +#define OP_GT 2 /* packet > value */ +#define OP_NP 3 /* new packet */ + +/* output opcodes */ +#define CL_REG 0 +#define LD_FID 1 +#define LD_SEQ 2 +#define LD_CTL 3 +#define LD_SAP 4 +#define LD_R1 5 +#define LD_L3 6 +#define LD_SUM 7 +#define LD_HDR 8 +#define IM_FID 9 +#define IM_SEQ 10 +#define IM_SAP 11 +#define IM_R1 12 +#define IM_CTL 13 +#define LD_LEN 14 +#define ST_FLG 15 + +/* match setp #s for IP4TCP4 */ +#define S1_PCKT 0 +#define S1_VLAN 1 +#define S1_CFI 2 +#define S1_8023 3 +#define S1_LLC 4 +#define S1_LLCc 5 +#define S1_IPV4 6 +#define S1_IPV4c 7 +#define S1_IPV4F 8 +#define S1_TCP44 9 +#define S1_IPV6 10 +#define S1_IPV6L 11 +#define S1_IPV6c 12 +#define S1_TCP64 13 +#define S1_TCPSQ 14 +#define S1_TCPFG 15 +#define S1_TCPHL 16 +#define S1_TCPHc 17 +#define S1_CLNP 18 +#define S1_CLNP2 19 +#define S1_DROP 20 +#define S2_HTTP 21 +#define S1_ESP4 22 +#define S1_AH4 23 +#define S1_ESP6 24 +#define S1_AH6 25 + +#define CAS_PROG_IP46TCP4_PREAMBLE \ +{ "packet arrival?", 0xffff, 0x0000, OP_NP, 6, S1_VLAN, 0, S1_PCKT, \ + CL_REG, 0x3ff, 1, 0x0, 0x0000}, \ +{ "VLAN?", 0xffff, 0x8100, OP_EQ, 1, S1_CFI, 0, S1_8023, \ + IM_CTL, 0x00a, 3, 0x0, 0xffff}, \ +{ "CFI?", 0x1000, 0x1000, OP_EQ, 0, S1_DROP, 1, S1_8023, \ + CL_REG, 0x000, 0, 0x0, 0x0000}, \ +{ "8023?", 0xffff, 0x0600, OP_LT, 1, S1_LLC, 0, S1_IPV4, \ + CL_REG, 0x000, 0, 0x0, 0x0000}, \ +{ "LLC?", 0xffff, 0xaaaa, OP_EQ, 1, S1_LLCc, 0, S1_CLNP, \ + CL_REG, 0x000, 0, 0x0, 0x0000}, \ +{ "LLCc?", 0xff00, 0x0300, OP_EQ, 2, S1_IPV4, 0, S1_CLNP, \ + CL_REG, 0x000, 0, 0x0, 0x0000}, \ +{ "IPV4?", 0xffff, 0x0800, OP_EQ, 1, S1_IPV4c, 0, S1_IPV6, \ + LD_SAP, 0x100, 3, 0x0, 0xffff}, \ +{ "IPV4 cont?", 0xff00, 0x4500, OP_EQ, 3, S1_IPV4F, 0, S1_CLNP, \ + LD_SUM, 0x00a, 1, 0x0, 0x0000}, \ +{ "IPV4 frag?", 0x3fff, 0x0000, OP_EQ, 1, S1_TCP44, 0, S1_CLNP, \ + LD_LEN, 0x03e, 1, 0x0, 0xffff}, \ +{ "TCP44?", 0x00ff, 0x0006, OP_EQ, 7, S1_TCPSQ, 0, S1_CLNP, \ + LD_FID, 0x182, 1, 0x0, 0xffff}, /* FID IP4&TCP src+dst */ \ +{ "IPV6?", 0xffff, 0x86dd, OP_EQ, 1, S1_IPV6L, 0, S1_CLNP, \ + LD_SUM, 0x015, 1, 0x0, 0x0000}, \ +{ "IPV6 len", 0xf000, 0x6000, OP_EQ, 0, S1_IPV6c, 0, S1_CLNP, \ + IM_R1, 0x128, 1, 0x0, 0xffff}, \ +{ "IPV6 cont?", 0x0000, 0x0000, OP_EQ, 3, S1_TCP64, 0, S1_CLNP, \ + LD_FID, 0x484, 1, 0x0, 0xffff}, /* FID IP6&TCP src+dst */ \ +{ "TCP64?", 0xff00, 0x0600, OP_EQ, 18, S1_TCPSQ, 0, S1_CLNP, \ + LD_LEN, 0x03f, 1, 0x0, 0xffff} + +#ifdef USE_HP_IP46TCP4 +static cas_hp_inst_t cas_prog_ip46tcp4tab[] = { + CAS_PROG_IP46TCP4_PREAMBLE, + { "TCP seq", /* DADDR should point to dest port */ + 0x0000, 0x0000, OP_EQ, 0, S1_TCPFG, 4, S1_TCPFG, LD_SEQ, + 0x081, 3, 0x0, 0xffff}, /* Load TCP seq # */ + { "TCP control flags", 0x0000, 0x0000, OP_EQ, 0, S1_TCPHL, 0, + S1_TCPHL, ST_FLG, 0x045, 3, 0x0, 0x002f}, /* Load TCP flags */ + { "TCP length", 0x0000, 0x0000, OP_EQ, 0, S1_TCPHc, 0, + S1_TCPHc, LD_R1, 0x205, 3, 0xB, 0xf000}, + { "TCP length cont", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, + S1_PCKT, LD_HDR, 0x0ff, 3, 0x0, 0xffff}, + { "Cleanup", 0x0000, 0x0000, OP_EQ, 0, S1_CLNP2, 0, S1_CLNP2, + IM_CTL, 0x001, 3, 0x0, 0x0001}, + { "Cleanup 2", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, S1_PCKT, + IM_CTL, 0x000, 0, 0x0, 0x0000}, + { "Drop packet", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, S1_PCKT, + IM_CTL, 0x080, 3, 0x0, 0xffff}, + { NULL }, +}; +#ifdef HP_IP46TCP4_DEFAULT +#define CAS_HP_FIRMWARE cas_prog_ip46tcp4tab +#endif +#endif + +/* + * Alternate table load which excludes HTTP server traffic from reassembly. + * It is substantially similar to the basic table, with one extra state + * and a few extra compares. */ +#ifdef USE_HP_IP46TCP4NOHTTP +static cas_hp_inst_t cas_prog_ip46tcp4nohttptab[] = { + CAS_PROG_IP46TCP4_PREAMBLE, + { "TCP seq", /* DADDR should point to dest port */ + 0xFFFF, 0x0080, OP_EQ, 0, S2_HTTP, 0, S1_TCPFG, LD_SEQ, + 0x081, 3, 0x0, 0xffff} , /* Load TCP seq # */ + { "TCP control flags", 0xFFFF, 0x8080, OP_EQ, 0, S2_HTTP, 0, + S1_TCPHL, ST_FLG, 0x145, 2, 0x0, 0x002f, }, /* Load TCP flags */ + { "TCP length", 0x0000, 0x0000, OP_EQ, 0, S1_TCPHc, 0, S1_TCPHc, + LD_R1, 0x205, 3, 0xB, 0xf000}, + { "TCP length cont", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, S1_PCKT, + LD_HDR, 0x0ff, 3, 0x0, 0xffff}, + { "Cleanup", 0x0000, 0x0000, OP_EQ, 0, S1_CLNP2, 0, S1_CLNP2, + IM_CTL, 0x001, 3, 0x0, 0x0001}, + { "Cleanup 2", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, S1_PCKT, + CL_REG, 0x002, 3, 0x0, 0x0000}, + { "Drop packet", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, S1_PCKT, + IM_CTL, 0x080, 3, 0x0, 0xffff}, + { "No HTTP", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, S1_PCKT, + IM_CTL, 0x044, 3, 0x0, 0xffff}, + { NULL }, +}; +#ifdef HP_IP46TCP4NOHTTP_DEFAULT +#define CAS_HP_FIRMWARE cas_prog_ip46tcp4nohttptab +#endif +#endif + +/* match step #s for IP4FRAG */ +#define S3_IPV6c 11 +#define S3_TCP64 12 +#define S3_TCPSQ 13 +#define S3_TCPFG 14 +#define S3_TCPHL 15 +#define S3_TCPHc 16 +#define S3_FRAG 17 +#define S3_FOFF 18 +#define S3_CLNP 19 + +#ifdef USE_HP_IP4FRAG +static cas_hp_inst_t cas_prog_ip4fragtab[] = { + { "packet arrival?", 0xffff, 0x0000, OP_NP, 6, S1_VLAN, 0, S1_PCKT, + CL_REG, 0x3ff, 1, 0x0, 0x0000}, + { "VLAN?", 0xffff, 0x8100, OP_EQ, 1, S1_CFI, 0, S1_8023, + IM_CTL, 0x00a, 3, 0x0, 0xffff}, + { "CFI?", 0x1000, 0x1000, OP_EQ, 0, S3_CLNP, 1, S1_8023, + CL_REG, 0x000, 0, 0x0, 0x0000}, + { "8023?", 0xffff, 0x0600, OP_LT, 1, S1_LLC, 0, S1_IPV4, + CL_REG, 0x000, 0, 0x0, 0x0000}, + { "LLC?", 0xffff, 0xaaaa, OP_EQ, 1, S1_LLCc, 0, S3_CLNP, + CL_REG, 0x000, 0, 0x0, 0x0000}, + { "LLCc?",0xff00, 0x0300, OP_EQ, 2, S1_IPV4, 0, S3_CLNP, + CL_REG, 0x000, 0, 0x0, 0x0000}, + { "IPV4?", 0xffff, 0x0800, OP_EQ, 1, S1_IPV4c, 0, S1_IPV6, + LD_SAP, 0x100, 3, 0x0, 0xffff}, + { "IPV4 cont?", 0xff00, 0x4500, OP_EQ, 3, S1_IPV4F, 0, S3_CLNP, + LD_SUM, 0x00a, 1, 0x0, 0x0000}, + { "IPV4 frag?", 0x3fff, 0x0000, OP_EQ, 1, S1_TCP44, 0, S3_FRAG, + LD_LEN, 0x03e, 3, 0x0, 0xffff}, + { "TCP44?", 0x00ff, 0x0006, OP_EQ, 7, S3_TCPSQ, 0, S3_CLNP, + LD_FID, 0x182, 3, 0x0, 0xffff}, /* FID IP4&TCP src+dst */ + { "IPV6?", 0xffff, 0x86dd, OP_EQ, 1, S3_IPV6c, 0, S3_CLNP, + LD_SUM, 0x015, 1, 0x0, 0x0000}, + { "IPV6 cont?", 0xf000, 0x6000, OP_EQ, 3, S3_TCP64, 0, S3_CLNP, + LD_FID, 0x484, 1, 0x0, 0xffff}, /* FID IP6&TCP src+dst */ + { "TCP64?", 0xff00, 0x0600, OP_EQ, 18, S3_TCPSQ, 0, S3_CLNP, + LD_LEN, 0x03f, 1, 0x0, 0xffff}, + { "TCP seq", /* DADDR should point to dest port */ + 0x0000, 0x0000, OP_EQ, 0, S3_TCPFG, 4, S3_TCPFG, LD_SEQ, + 0x081, 3, 0x0, 0xffff}, /* Load TCP seq # */ + { "TCP control flags", 0x0000, 0x0000, OP_EQ, 0, S3_TCPHL, 0, + S3_TCPHL, ST_FLG, 0x045, 3, 0x0, 0x002f}, /* Load TCP flags */ + { "TCP length", 0x0000, 0x0000, OP_EQ, 0, S3_TCPHc, 0, S3_TCPHc, + LD_R1, 0x205, 3, 0xB, 0xf000}, + { "TCP length cont", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, S1_PCKT, + LD_HDR, 0x0ff, 3, 0x0, 0xffff}, + { "IP4 Fragment", 0x0000, 0x0000, OP_EQ, 0, S3_FOFF, 0, S3_FOFF, + LD_FID, 0x103, 3, 0x0, 0xffff}, /* FID IP4 src+dst */ + { "IP4 frag offset", 0x0000, 0x0000, OP_EQ, 0, S3_FOFF, 0, S3_FOFF, + LD_SEQ, 0x040, 1, 0xD, 0xfff8}, + { "Cleanup", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, S1_PCKT, + IM_CTL, 0x001, 3, 0x0, 0x0001}, + { NULL }, +}; +#ifdef HP_IP4FRAG_DEFAULT +#define CAS_HP_FIRMWARE cas_prog_ip4fragtab +#endif +#endif + +/* + * Alternate table which does batching without reassembly + */ +#ifdef USE_HP_IP46TCP4BATCH +static cas_hp_inst_t cas_prog_ip46tcp4batchtab[] = { + CAS_PROG_IP46TCP4_PREAMBLE, + { "TCP seq", /* DADDR should point to dest port */ + 0x0000, 0x0000, OP_EQ, 0, S1_TCPFG, 0, S1_TCPFG, LD_SEQ, + 0x081, 3, 0x0, 0xffff}, /* Load TCP seq # */ + { "TCP control flags", 0x0000, 0x0000, OP_EQ, 0, S1_TCPHL, 0, + S1_TCPHL, ST_FLG, 0x000, 3, 0x0, 0x0000}, /* Load TCP flags */ + { "TCP length", 0x0000, 0x0000, OP_EQ, 0, S1_TCPHc, 0, + S1_TCPHc, LD_R1, 0x205, 3, 0xB, 0xf000}, + { "TCP length cont", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, + S1_PCKT, IM_CTL, 0x040, 3, 0x0, 0xffff}, /* set batch bit */ + { "Cleanup", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, S1_PCKT, + IM_CTL, 0x001, 3, 0x0, 0x0001}, + { "Drop packet", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, + S1_PCKT, IM_CTL, 0x080, 3, 0x0, 0xffff}, + { NULL }, +}; +#ifdef HP_IP46TCP4BATCH_DEFAULT +#define CAS_HP_FIRMWARE cas_prog_ip46tcp4batchtab +#endif +#endif + +/* Workaround for Cassini rev2 descriptor corruption problem. + * Does batching without reassembly, and sets the SAP to a known + * data pattern for all packets. + */ +#ifdef USE_HP_WORKAROUND +static cas_hp_inst_t cas_prog_workaroundtab[] = { + { "packet arrival?", 0xffff, 0x0000, OP_NP, 6, S1_VLAN, 0, + S1_PCKT, CL_REG, 0x3ff, 1, 0x0, 0x0000} , + { "VLAN?", 0xffff, 0x8100, OP_EQ, 1, S1_CFI, 0, S1_8023, + IM_CTL, 0x04a, 3, 0x0, 0xffff}, + { "CFI?", 0x1000, 0x1000, OP_EQ, 0, S1_CLNP, 1, S1_8023, + CL_REG, 0x000, 0, 0x0, 0x0000}, + { "8023?", 0xffff, 0x0600, OP_LT, 1, S1_LLC, 0, S1_IPV4, + CL_REG, 0x000, 0, 0x0, 0x0000}, + { "LLC?", 0xffff, 0xaaaa, OP_EQ, 1, S1_LLCc, 0, S1_CLNP, + CL_REG, 0x000, 0, 0x0, 0x0000}, + { "LLCc?", 0xff00, 0x0300, OP_EQ, 2, S1_IPV4, 0, S1_CLNP, + CL_REG, 0x000, 0, 0x0, 0x0000}, + { "IPV4?", 0xffff, 0x0800, OP_EQ, 1, S1_IPV4c, 0, S1_IPV6, + IM_SAP, 0x6AE, 3, 0x0, 0xffff}, + { "IPV4 cont?", 0xff00, 0x4500, OP_EQ, 3, S1_IPV4F, 0, S1_CLNP, + LD_SUM, 0x00a, 1, 0x0, 0x0000}, + { "IPV4 frag?", 0x3fff, 0x0000, OP_EQ, 1, S1_TCP44, 0, S1_CLNP, + LD_LEN, 0x03e, 1, 0x0, 0xffff}, + { "TCP44?", 0x00ff, 0x0006, OP_EQ, 7, S1_TCPSQ, 0, S1_CLNP, + LD_FID, 0x182, 3, 0x0, 0xffff}, /* FID IP4&TCP src+dst */ + { "IPV6?", 0xffff, 0x86dd, OP_EQ, 1, S1_IPV6L, 0, S1_CLNP, + LD_SUM, 0x015, 1, 0x0, 0x0000}, + { "IPV6 len", 0xf000, 0x6000, OP_EQ, 0, S1_IPV6c, 0, S1_CLNP, + IM_R1, 0x128, 1, 0x0, 0xffff}, + { "IPV6 cont?", 0x0000, 0x0000, OP_EQ, 3, S1_TCP64, 0, S1_CLNP, + LD_FID, 0x484, 1, 0x0, 0xffff}, /* FID IP6&TCP src+dst */ + { "TCP64?", 0xff00, 0x0600, OP_EQ, 18, S1_TCPSQ, 0, S1_CLNP, + LD_LEN, 0x03f, 1, 0x0, 0xffff}, + { "TCP seq", /* DADDR should point to dest port */ + 0x0000, 0x0000, OP_EQ, 0, S1_TCPFG, 4, S1_TCPFG, LD_SEQ, + 0x081, 3, 0x0, 0xffff}, /* Load TCP seq # */ + { "TCP control flags", 0x0000, 0x0000, OP_EQ, 0, S1_TCPHL, 0, + S1_TCPHL, ST_FLG, 0x045, 3, 0x0, 0x002f}, /* Load TCP flags */ + { "TCP length", 0x0000, 0x0000, OP_EQ, 0, S1_TCPHc, 0, S1_TCPHc, + LD_R1, 0x205, 3, 0xB, 0xf000}, + { "TCP length cont", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, + S1_PCKT, LD_HDR, 0x0ff, 3, 0x0, 0xffff}, + { "Cleanup", 0x0000, 0x0000, OP_EQ, 0, S1_CLNP2, 0, S1_CLNP2, + IM_SAP, 0x6AE, 3, 0x0, 0xffff} , + { "Cleanup 2", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, S1_PCKT, + IM_CTL, 0x001, 3, 0x0, 0x0001}, + { NULL }, +}; +#ifdef HP_WORKAROUND_DEFAULT +#define CAS_HP_FIRMWARE cas_prog_workaroundtab +#endif +#endif + +#ifdef USE_HP_ENCRYPT +static cas_hp_inst_t cas_prog_encryptiontab[] = { + { "packet arrival?", 0xffff, 0x0000, OP_NP, 6, S1_VLAN, 0, + S1_PCKT, CL_REG, 0x3ff, 1, 0x0, 0x0000}, + { "VLAN?", 0xffff, 0x8100, OP_EQ, 1, S1_CFI, 0, S1_8023, + IM_CTL, 0x00a, 3, 0x0, 0xffff}, +#if 0 +//"CFI?", /* 02 FIND CFI and If FIND go to S1_DROP */ +//0x1000, 0x1000, OP_EQ, 0, S1_DROP, 1, S1_8023, CL_REG, 0x000, 0, 0x0, 0x00 + 00, +#endif + { "CFI?", /* FIND CFI and If FIND go to CleanUP1 (ignore and send to host) */ + 0x1000, 0x1000, OP_EQ, 0, S1_CLNP, 1, S1_8023, + CL_REG, 0x000, 0, 0x0, 0x0000}, + { "8023?", 0xffff, 0x0600, OP_LT, 1, S1_LLC, 0, S1_IPV4, + CL_REG, 0x000, 0, 0x0, 0x0000}, + { "LLC?", 0xffff, 0xaaaa, OP_EQ, 1, S1_LLCc, 0, S1_CLNP, + CL_REG, 0x000, 0, 0x0, 0x0000}, + { "LLCc?", 0xff00, 0x0300, OP_EQ, 2, S1_IPV4, 0, S1_CLNP, + CL_REG, 0x000, 0, 0x0, 0x0000}, + { "IPV4?", 0xffff, 0x0800, OP_EQ, 1, S1_IPV4c, 0, S1_IPV6, + LD_SAP, 0x100, 3, 0x0, 0xffff}, + { "IPV4 cont?", 0xff00, 0x4500, OP_EQ, 3, S1_IPV4F, 0, S1_CLNP, + LD_SUM, 0x00a, 1, 0x0, 0x0000}, + { "IPV4 frag?", 0x3fff, 0x0000, OP_EQ, 1, S1_TCP44, 0, S1_CLNP, + LD_LEN, 0x03e, 1, 0x0, 0xffff}, + { "TCP44?", 0x00ff, 0x0006, OP_EQ, 7, S1_TCPSQ, 0, S1_ESP4, + LD_FID, 0x182, 1, 0x0, 0xffff}, /* FID IP4&TCP src+dst */ + { "IPV6?", 0xffff, 0x86dd, OP_EQ, 1, S1_IPV6L, 0, S1_CLNP, + LD_SUM, 0x015, 1, 0x0, 0x0000}, + { "IPV6 len", 0xf000, 0x6000, OP_EQ, 0, S1_IPV6c, 0, S1_CLNP, + IM_R1, 0x128, 1, 0x0, 0xffff}, + { "IPV6 cont?", 0x0000, 0x0000, OP_EQ, 3, S1_TCP64, 0, S1_CLNP, + LD_FID, 0x484, 1, 0x0, 0xffff}, /* FID IP6&TCP src+dst */ + { "TCP64?", +#if 0 +//@@@0xff00, 0x0600, OP_EQ, 18, S1_TCPSQ, 0, S1_ESP6, LD_LEN, 0x03f, 1, 0x0, 0xffff, +#endif + 0xff00, 0x0600, OP_EQ, 12, S1_TCPSQ, 0, S1_ESP6, LD_LEN, + 0x03f, 1, 0x0, 0xffff}, + { "TCP seq", /* 14:DADDR should point to dest port */ + 0xFFFF, 0x0080, OP_EQ, 0, S2_HTTP, 0, S1_TCPFG, LD_SEQ, + 0x081, 3, 0x0, 0xffff}, /* Load TCP seq # */ + { "TCP control flags", 0xFFFF, 0x8080, OP_EQ, 0, S2_HTTP, 0, + S1_TCPHL, ST_FLG, 0x145, 2, 0x0, 0x002f}, /* Load TCP flags */ + { "TCP length", 0x0000, 0x0000, OP_EQ, 0, S1_TCPHc, 0, S1_TCPHc, + LD_R1, 0x205, 3, 0xB, 0xf000} , + { "TCP length cont", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, + S1_PCKT, LD_HDR, 0x0ff, 3, 0x0, 0xffff}, + { "Cleanup", 0x0000, 0x0000, OP_EQ, 0, S1_CLNP2, 0, S1_CLNP2, + IM_CTL, 0x001, 3, 0x0, 0x0001}, + { "Cleanup 2", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, S1_PCKT, + CL_REG, 0x002, 3, 0x0, 0x0000}, + { "Drop packet", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, S1_PCKT, + IM_CTL, 0x080, 3, 0x0, 0xffff}, + { "No HTTP", 0x0000, 0x0000, OP_EQ, 0, S1_PCKT, 0, S1_PCKT, + IM_CTL, 0x044, 3, 0x0, 0xffff}, + { "IPV4 ESP encrypted?", /* S1_ESP4 */ + 0x00ff, 0x0032, OP_EQ, 0, S1_CLNP2, 0, S1_AH4, IM_CTL, + 0x021, 1, 0x0, 0xffff}, + { "IPV4 AH encrypted?", /* S1_AH4 */ + 0x00ff, 0x0033, OP_EQ, 0, S1_CLNP2, 0, S1_CLNP, IM_CTL, + 0x021, 1, 0x0, 0xffff}, + { "IPV6 ESP encrypted?", /* S1_ESP6 */ +#if 0 +//@@@0x00ff, 0x0032, OP_EQ, 0, S1_CLNP2, 0, S1_AH6, IM_CTL, 0x021, 1, 0x0, 0xffff, +#endif + 0xff00, 0x3200, OP_EQ, 0, S1_CLNP2, 0, S1_AH6, IM_CTL, + 0x021, 1, 0x0, 0xffff}, + { "IPV6 AH encrypted?", /* S1_AH6 */ +#if 0 +//@@@0x00ff, 0x0033, OP_EQ, 0, S1_CLNP2, 0, S1_CLNP, IM_CTL, 0x021, 1, 0x0, 0xffff, +#endif + 0xff00, 0x3300, OP_EQ, 0, S1_CLNP2, 0, S1_CLNP, IM_CTL, + 0x021, 1, 0x0, 0xffff}, + { NULL }, +}; +#ifdef HP_ENCRYPT_DEFAULT +#define CAS_HP_FIRMWARE cas_prog_encryptiontab +#endif +#endif + +static cas_hp_inst_t cas_prog_null[] = { {NULL} }; +#ifdef HP_NULL_DEFAULT +#define CAS_HP_FIRMWARE cas_prog_null +#endif + +/* phy types */ +#define CAS_PHY_UNKNOWN 0x00 +#define CAS_PHY_SERDES 0x01 +#define CAS_PHY_MII_MDIO0 0x02 +#define CAS_PHY_MII_MDIO1 0x04 +#define CAS_PHY_MII(x) ((x) & (CAS_PHY_MII_MDIO0 | CAS_PHY_MII_MDIO1)) + +/* _RING_INDEX is the index for the ring sizes to be used. _RING_SIZE + * is the actual size. the default index for the various rings is + * 8. NOTE: there a bunch of alignment constraints for the rings. to + * deal with that, i just allocate rings to create the desired + * alignment. here are the constraints: + * RX DESC and COMP rings must be 8KB aligned + * TX DESC must be 2KB aligned. + * if you change the numbers, be cognizant of how the alignment will change + * in INIT_BLOCK as well. + */ + +#define DESC_RING_I_TO_S(x) (32*(1 << (x))) +#define COMP_RING_I_TO_S(x) (128*(1 << (x))) +#define TX_DESC_RING_INDEX 4 /* 512 = 8k */ +#define RX_DESC_RING_INDEX 4 /* 512 = 8k */ +#define RX_COMP_RING_INDEX 4 /* 2048 = 64k: should be 4x rx ring size */ + +#if (TX_DESC_RING_INDEX > 8) || (TX_DESC_RING_INDEX < 0) +#error TX_DESC_RING_INDEX must be between 0 and 8 +#endif + +#if (RX_DESC_RING_INDEX > 8) || (RX_DESC_RING_INDEX < 0) +#error RX_DESC_RING_INDEX must be between 0 and 8 +#endif + +#if (RX_COMP_RING_INDEX > 8) || (RX_COMP_RING_INDEX < 0) +#error RX_COMP_RING_INDEX must be between 0 and 8 +#endif + +#define N_TX_RINGS MAX_TX_RINGS /* for QoS */ +#define N_TX_RINGS_MASK MAX_TX_RINGS_MASK +#define N_RX_DESC_RINGS MAX_RX_DESC_RINGS /* 1 for ipsec */ +#define N_RX_COMP_RINGS 0x1 /* for mult. PCI interrupts */ + +/* number of flows that can go through re-assembly */ +#define N_RX_FLOWS 64 + +#define TX_DESC_RING_SIZE DESC_RING_I_TO_S(TX_DESC_RING_INDEX) +#define RX_DESC_RING_SIZE DESC_RING_I_TO_S(RX_DESC_RING_INDEX) +#define RX_COMP_RING_SIZE COMP_RING_I_TO_S(RX_COMP_RING_INDEX) +#define TX_DESC_RINGN_INDEX(x) TX_DESC_RING_INDEX +#define RX_DESC_RINGN_INDEX(x) RX_DESC_RING_INDEX +#define RX_COMP_RINGN_INDEX(x) RX_COMP_RING_INDEX +#define TX_DESC_RINGN_SIZE(x) TX_DESC_RING_SIZE +#define RX_DESC_RINGN_SIZE(x) RX_DESC_RING_SIZE +#define RX_COMP_RINGN_SIZE(x) RX_COMP_RING_SIZE + +/* convert values */ +#define CAS_BASE(x, y) (((y) << (x ## _SHIFT)) & (x ## _MASK)) +#define CAS_VAL(x, y) (((y) & (x ## _MASK)) >> (x ## _SHIFT)) +#define CAS_TX_RINGN_BASE(y) ((TX_DESC_RINGN_INDEX(y) << \ + TX_CFG_DESC_RINGN_SHIFT(y)) & \ + TX_CFG_DESC_RINGN_MASK(y)) + +/* min is 2k, but we can't do jumbo frames unless it's at least 8k */ +#define CAS_MIN_PAGE_SHIFT 11 /* 2048 */ +#define CAS_JUMBO_PAGE_SHIFT 13 /* 8192 */ +#define CAS_MAX_PAGE_SHIFT 14 /* 16384 */ + +#define TX_DESC_BUFLEN_MASK 0x0000000000003FFFULL /* buffer length in + bytes. 0 - 9256 */ +#define TX_DESC_BUFLEN_SHIFT 0 +#define TX_DESC_CSUM_START_MASK 0x00000000001F8000ULL /* checksum start. # + of bytes to be + skipped before + csum calc begins. + value must be + even */ +#define TX_DESC_CSUM_START_SHIFT 15 +#define TX_DESC_CSUM_STUFF_MASK 0x000000001FE00000ULL /* checksum stuff. + byte offset w/in + the pkt for the + 1st csum byte. + must be > 8 */ +#define TX_DESC_CSUM_STUFF_SHIFT 21 +#define TX_DESC_CSUM_EN 0x0000000020000000ULL /* enable checksum */ +#define TX_DESC_EOF 0x0000000040000000ULL /* end of frame */ +#define TX_DESC_SOF 0x0000000080000000ULL /* start of frame */ +#define TX_DESC_INTME 0x0000000100000000ULL /* interrupt me */ +#define TX_DESC_NO_CRC 0x0000000200000000ULL /* debugging only. + CRC will not be + inserted into + outgoing frame. */ +struct cas_tx_desc { + __le64 control; + __le64 buffer; +}; + +/* descriptor ring for free buffers contains page-sized buffers. the index + * value is not used by the hw in any way. it's just stored and returned in + * the completion ring. + */ +struct cas_rx_desc { + __le64 index; + __le64 buffer; +}; + +/* received packets are put on the completion ring. */ +/* word 1 */ +#define RX_COMP1_DATA_SIZE_MASK 0x0000000007FFE000ULL +#define RX_COMP1_DATA_SIZE_SHIFT 13 +#define RX_COMP1_DATA_OFF_MASK 0x000001FFF8000000ULL +#define RX_COMP1_DATA_OFF_SHIFT 27 +#define RX_COMP1_DATA_INDEX_MASK 0x007FFE0000000000ULL +#define RX_COMP1_DATA_INDEX_SHIFT 41 +#define RX_COMP1_SKIP_MASK 0x0180000000000000ULL +#define RX_COMP1_SKIP_SHIFT 55 +#define RX_COMP1_RELEASE_NEXT 0x0200000000000000ULL +#define RX_COMP1_SPLIT_PKT 0x0400000000000000ULL +#define RX_COMP1_RELEASE_FLOW 0x0800000000000000ULL +#define RX_COMP1_RELEASE_DATA 0x1000000000000000ULL +#define RX_COMP1_RELEASE_HDR 0x2000000000000000ULL +#define RX_COMP1_TYPE_MASK 0xC000000000000000ULL +#define RX_COMP1_TYPE_SHIFT 62 + +/* word 2 */ +#define RX_COMP2_NEXT_INDEX_MASK 0x00000007FFE00000ULL +#define RX_COMP2_NEXT_INDEX_SHIFT 21 +#define RX_COMP2_HDR_SIZE_MASK 0x00000FF800000000ULL +#define RX_COMP2_HDR_SIZE_SHIFT 35 +#define RX_COMP2_HDR_OFF_MASK 0x0003F00000000000ULL +#define RX_COMP2_HDR_OFF_SHIFT 44 +#define RX_COMP2_HDR_INDEX_MASK 0xFFFC000000000000ULL +#define RX_COMP2_HDR_INDEX_SHIFT 50 + +/* word 3 */ +#define RX_COMP3_SMALL_PKT 0x0000000000000001ULL +#define RX_COMP3_JUMBO_PKT 0x0000000000000002ULL +#define RX_COMP3_JUMBO_HDR_SPLIT_EN 0x0000000000000004ULL +#define RX_COMP3_CSUM_START_MASK 0x000000000007F000ULL +#define RX_COMP3_CSUM_START_SHIFT 12 +#define RX_COMP3_FLOWID_MASK 0x0000000001F80000ULL +#define RX_COMP3_FLOWID_SHIFT 19 +#define RX_COMP3_OPCODE_MASK 0x000000000E000000ULL +#define RX_COMP3_OPCODE_SHIFT 25 +#define RX_COMP3_FORCE_FLAG 0x0000000010000000ULL +#define RX_COMP3_NO_ASSIST 0x0000000020000000ULL +#define RX_COMP3_LOAD_BAL_MASK 0x000001F800000000ULL +#define RX_COMP3_LOAD_BAL_SHIFT 35 +#define RX_PLUS_COMP3_ENC_PKT 0x0000020000000000ULL /* cas+ */ +#define RX_COMP3_L3_HEAD_OFF_MASK 0x0000FE0000000000ULL /* cas */ +#define RX_COMP3_L3_HEAD_OFF_SHIFT 41 +#define RX_PLUS_COMP_L3_HEAD_OFF_MASK 0x0000FC0000000000ULL /* cas+ */ +#define RX_PLUS_COMP_L3_HEAD_OFF_SHIFT 42 +#define RX_COMP3_SAP_MASK 0xFFFF000000000000ULL +#define RX_COMP3_SAP_SHIFT 48 + +/* word 4 */ +#define RX_COMP4_TCP_CSUM_MASK 0x000000000000FFFFULL +#define RX_COMP4_TCP_CSUM_SHIFT 0 +#define RX_COMP4_PKT_LEN_MASK 0x000000003FFF0000ULL +#define RX_COMP4_PKT_LEN_SHIFT 16 +#define RX_COMP4_PERFECT_MATCH_MASK 0x00000003C0000000ULL +#define RX_COMP4_PERFECT_MATCH_SHIFT 30 +#define RX_COMP4_ZERO 0x0000080000000000ULL +#define RX_COMP4_HASH_VAL_MASK 0x0FFFF00000000000ULL +#define RX_COMP4_HASH_VAL_SHIFT 44 +#define RX_COMP4_HASH_PASS 0x1000000000000000ULL +#define RX_COMP4_BAD 0x4000000000000000ULL +#define RX_COMP4_LEN_MISMATCH 0x8000000000000000ULL + +/* we encode the following: ring/index/release. only 14 bits + * are usable. + * NOTE: the encoding is dependent upon RX_DESC_RING_SIZE and + * MAX_RX_DESC_RINGS. */ +#define RX_INDEX_NUM_MASK 0x0000000000000FFFULL +#define RX_INDEX_NUM_SHIFT 0 +#define RX_INDEX_RING_MASK 0x0000000000001000ULL +#define RX_INDEX_RING_SHIFT 12 +#define RX_INDEX_RELEASE 0x0000000000002000ULL + +struct cas_rx_comp { + __le64 word1; + __le64 word2; + __le64 word3; + __le64 word4; +}; + +enum link_state { + link_down = 0, /* No link, will retry */ + link_aneg, /* Autoneg in progress */ + link_force_try, /* Try Forced link speed */ + link_force_ret, /* Forced mode worked, retrying autoneg */ + link_force_ok, /* Stay in forced mode */ + link_up /* Link is up */ +}; + +typedef struct cas_page { + struct list_head list; + struct page *buffer; + dma_addr_t dma_addr; + int used; +} cas_page_t; + + +/* some alignment constraints: + * TX DESC, RX DESC, and RX COMP must each be 8K aligned. + * TX COMPWB must be 8-byte aligned. + * to accomplish this, here's what we do: + * + * INIT_BLOCK_RX_COMP = 64k (already aligned) + * INIT_BLOCK_RX_DESC = 8k + * INIT_BLOCK_TX = 8k + * INIT_BLOCK_RX1_DESC = 8k + * TX COMPWB + */ +#define INIT_BLOCK_TX (TX_DESC_RING_SIZE) +#define INIT_BLOCK_RX_DESC (RX_DESC_RING_SIZE) +#define INIT_BLOCK_RX_COMP (RX_COMP_RING_SIZE) + +struct cas_init_block { + struct cas_rx_comp rxcs[N_RX_COMP_RINGS][INIT_BLOCK_RX_COMP]; + struct cas_rx_desc rxds[N_RX_DESC_RINGS][INIT_BLOCK_RX_DESC]; + struct cas_tx_desc txds[N_TX_RINGS][INIT_BLOCK_TX]; + __le64 tx_compwb; +}; + +/* tiny buffers to deal with target abort issue. we allocate a bit + * over so that we don't have target abort issues with these buffers + * as well. + */ +#define TX_TINY_BUF_LEN 0x100 +#define TX_TINY_BUF_BLOCK ((INIT_BLOCK_TX + 1)*TX_TINY_BUF_LEN) + +struct cas_tiny_count { + int nbufs; + int used; +}; + +struct cas { + spinlock_t lock; /* for most bits */ + spinlock_t tx_lock[N_TX_RINGS]; /* tx bits */ + spinlock_t stat_lock[N_TX_RINGS + 1]; /* for stat gathering */ + spinlock_t rx_inuse_lock; /* rx inuse list */ + spinlock_t rx_spare_lock; /* rx spare list */ + + void __iomem *regs; + int tx_new[N_TX_RINGS], tx_old[N_TX_RINGS]; + int rx_old[N_RX_DESC_RINGS]; + int rx_cur[N_RX_COMP_RINGS], rx_new[N_RX_COMP_RINGS]; + int rx_last[N_RX_DESC_RINGS]; + + struct napi_struct napi; + + /* Set when chip is actually in operational state + * (ie. not power managed) */ + int hw_running; + int opened; + struct mutex pm_mutex; /* open/close/suspend/resume */ + + struct cas_init_block *init_block; + struct cas_tx_desc *init_txds[MAX_TX_RINGS]; + struct cas_rx_desc *init_rxds[MAX_RX_DESC_RINGS]; + struct cas_rx_comp *init_rxcs[MAX_RX_COMP_RINGS]; + + /* we use sk_buffs for tx and pages for rx. the rx skbuffs + * are there for flow re-assembly. */ + struct sk_buff *tx_skbs[N_TX_RINGS][TX_DESC_RING_SIZE]; + struct sk_buff_head rx_flows[N_RX_FLOWS]; + cas_page_t *rx_pages[N_RX_DESC_RINGS][RX_DESC_RING_SIZE]; + struct list_head rx_spare_list, rx_inuse_list; + int rx_spares_needed; + + /* for small packets when copying would be quicker than + mapping */ + struct cas_tiny_count tx_tiny_use[N_TX_RINGS][TX_DESC_RING_SIZE]; + u8 *tx_tiny_bufs[N_TX_RINGS]; + + u32 msg_enable; + + /* N_TX_RINGS must be >= N_RX_DESC_RINGS */ + struct net_device_stats net_stats[N_TX_RINGS + 1]; + + u32 pci_cfg[64 >> 2]; + u8 pci_revision; + + int phy_type; + int phy_addr; + u32 phy_id; +#define CAS_FLAG_1000MB_CAP 0x00000001 +#define CAS_FLAG_REG_PLUS 0x00000002 +#define CAS_FLAG_TARGET_ABORT 0x00000004 +#define CAS_FLAG_SATURN 0x00000008 +#define CAS_FLAG_RXD_POST_MASK 0x000000F0 +#define CAS_FLAG_RXD_POST_SHIFT 4 +#define CAS_FLAG_RXD_POST(x) ((1 << (CAS_FLAG_RXD_POST_SHIFT + (x))) & \ + CAS_FLAG_RXD_POST_MASK) +#define CAS_FLAG_ENTROPY_DEV 0x00000100 +#define CAS_FLAG_NO_HW_CSUM 0x00000200 + u32 cas_flags; + int packet_min; /* minimum packet size */ + int tx_fifo_size; + int rx_fifo_size; + int rx_pause_off; + int rx_pause_on; + int crc_size; /* 4 if half-duplex */ + + int pci_irq_INTC; + int min_frame_size; /* for tx fifo workaround */ + + /* page size allocation */ + int page_size; + int page_order; + int mtu_stride; + + u32 mac_rx_cfg; + + /* Autoneg & PHY control */ + int link_cntl; + int link_fcntl; + enum link_state lstate; + struct timer_list link_timer; + int timer_ticks; + struct work_struct reset_task; +#if 0 + atomic_t reset_task_pending; +#else + atomic_t reset_task_pending; + atomic_t reset_task_pending_mtu; + atomic_t reset_task_pending_spare; + atomic_t reset_task_pending_all; +#endif + + /* Link-down problem workaround */ +#define LINK_TRANSITION_UNKNOWN 0 +#define LINK_TRANSITION_ON_FAILURE 1 +#define LINK_TRANSITION_STILL_FAILED 2 +#define LINK_TRANSITION_LINK_UP 3 +#define LINK_TRANSITION_LINK_CONFIG 4 +#define LINK_TRANSITION_LINK_DOWN 5 +#define LINK_TRANSITION_REQUESTED_RESET 6 + int link_transition; + int link_transition_jiffies_valid; + unsigned long link_transition_jiffies; + + /* Tuning */ + u8 orig_cacheline_size; /* value when loaded */ +#define CAS_PREF_CACHELINE_SIZE 0x20 /* Minimum desired */ + + /* Diagnostic counters and state. */ + int casreg_len; /* reg-space size for dumping */ + u64 pause_entered; + u16 pause_last_time_recvd; + + dma_addr_t block_dvma, tx_tiny_dvma[N_TX_RINGS]; + struct pci_dev *pdev; + struct net_device *dev; +#if defined(CONFIG_OF) + struct device_node *of_node; +#endif + + /* Firmware Info */ + u16 fw_load_addr; + u32 fw_size; + u8 *fw_data; +}; + +#define TX_DESC_NEXT(r, x) (((x) + 1) & (TX_DESC_RINGN_SIZE(r) - 1)) +#define RX_DESC_ENTRY(r, x) ((x) & (RX_DESC_RINGN_SIZE(r) - 1)) +#define RX_COMP_ENTRY(r, x) ((x) & (RX_COMP_RINGN_SIZE(r) - 1)) + +#define TX_BUFF_COUNT(r, x, y) ((x) <= (y) ? ((y) - (x)) : \ + (TX_DESC_RINGN_SIZE(r) - (x) + (y))) + +#define TX_BUFFS_AVAIL(cp, i) ((cp)->tx_old[(i)] <= (cp)->tx_new[(i)] ? \ + (cp)->tx_old[(i)] + (TX_DESC_RINGN_SIZE(i) - 1) - (cp)->tx_new[(i)] : \ + (cp)->tx_old[(i)] - (cp)->tx_new[(i)] - 1) + +#define CAS_ALIGN(addr, align) \ + (((unsigned long) (addr) + ((align) - 1UL)) & ~((align) - 1)) + +#define RX_FIFO_SIZE 16384 +#define EXPANSION_ROM_SIZE 65536 + +#define CAS_MC_EXACT_MATCH_SIZE 15 +#define CAS_MC_HASH_SIZE 256 +#define CAS_MC_HASH_MAX (CAS_MC_EXACT_MATCH_SIZE + \ + CAS_MC_HASH_SIZE) + +#define TX_TARGET_ABORT_LEN 0x20 +#define RX_SWIVEL_OFF_VAL 0x2 +#define RX_AE_FREEN_VAL(x) (RX_DESC_RINGN_SIZE(x) >> 1) +#define RX_AE_COMP_VAL (RX_COMP_RING_SIZE >> 1) +#define RX_BLANK_INTR_PKT_VAL 0x05 +#define RX_BLANK_INTR_TIME_VAL 0x0F +#define HP_TCP_THRESH_VAL 1530 /* reduce to enable reassembly */ + +#define RX_SPARE_COUNT (RX_DESC_RING_SIZE >> 1) +#define RX_SPARE_RECOVER_VAL (RX_SPARE_COUNT >> 2) + +#endif /* _CASSINI_H */ |