diff options
Diffstat (limited to 'drivers/net/phy/at803x.c')
| -rw-r--r-- | drivers/net/phy/at803x.c | 2194 |
1 files changed, 2194 insertions, 0 deletions
diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c new file mode 100644 index 000000000..edd4b1e58 --- /dev/null +++ b/drivers/net/phy/at803x.c @@ -0,0 +1,2194 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * drivers/net/phy/at803x.c + * + * Driver for Qualcomm Atheros AR803x PHY + * + * Author: Matus Ujhelyi <ujhelyi.m@gmail.com> + */ + +#include <linux/phy.h> +#include <linux/module.h> +#include <linux/string.h> +#include <linux/netdevice.h> +#include <linux/etherdevice.h> +#include <linux/ethtool_netlink.h> +#include <linux/of_gpio.h> +#include <linux/bitfield.h> +#include <linux/gpio/consumer.h> +#include <linux/regulator/of_regulator.h> +#include <linux/regulator/driver.h> +#include <linux/regulator/consumer.h> +#include <linux/phylink.h> +#include <linux/sfp.h> +#include <dt-bindings/net/qca-ar803x.h> + +#define AT803X_SPECIFIC_FUNCTION_CONTROL 0x10 +#define AT803X_SFC_ASSERT_CRS BIT(11) +#define AT803X_SFC_FORCE_LINK BIT(10) +#define AT803X_SFC_MDI_CROSSOVER_MODE_M GENMASK(6, 5) +#define AT803X_SFC_AUTOMATIC_CROSSOVER 0x3 +#define AT803X_SFC_MANUAL_MDIX 0x1 +#define AT803X_SFC_MANUAL_MDI 0x0 +#define AT803X_SFC_SQE_TEST BIT(2) +#define AT803X_SFC_POLARITY_REVERSAL BIT(1) +#define AT803X_SFC_DISABLE_JABBER BIT(0) + +#define AT803X_SPECIFIC_STATUS 0x11 +#define AT803X_SS_SPEED_MASK GENMASK(15, 14) +#define AT803X_SS_SPEED_1000 2 +#define AT803X_SS_SPEED_100 1 +#define AT803X_SS_SPEED_10 0 +#define AT803X_SS_DUPLEX BIT(13) +#define AT803X_SS_SPEED_DUPLEX_RESOLVED BIT(11) +#define AT803X_SS_MDIX BIT(6) + +#define QCA808X_SS_SPEED_MASK GENMASK(9, 7) +#define QCA808X_SS_SPEED_2500 4 + +#define AT803X_INTR_ENABLE 0x12 +#define AT803X_INTR_ENABLE_AUTONEG_ERR BIT(15) +#define AT803X_INTR_ENABLE_SPEED_CHANGED BIT(14) +#define AT803X_INTR_ENABLE_DUPLEX_CHANGED BIT(13) +#define AT803X_INTR_ENABLE_PAGE_RECEIVED BIT(12) +#define AT803X_INTR_ENABLE_LINK_FAIL BIT(11) +#define AT803X_INTR_ENABLE_LINK_SUCCESS BIT(10) +#define AT803X_INTR_ENABLE_LINK_FAIL_BX BIT(8) +#define AT803X_INTR_ENABLE_LINK_SUCCESS_BX BIT(7) +#define AT803X_INTR_ENABLE_WIRESPEED_DOWNGRADE BIT(5) +#define AT803X_INTR_ENABLE_POLARITY_CHANGED BIT(1) +#define AT803X_INTR_ENABLE_WOL BIT(0) + +#define AT803X_INTR_STATUS 0x13 + +#define AT803X_SMART_SPEED 0x14 +#define AT803X_SMART_SPEED_ENABLE BIT(5) +#define AT803X_SMART_SPEED_RETRY_LIMIT_MASK GENMASK(4, 2) +#define AT803X_SMART_SPEED_BYPASS_TIMER BIT(1) +#define AT803X_CDT 0x16 +#define AT803X_CDT_MDI_PAIR_MASK GENMASK(9, 8) +#define AT803X_CDT_ENABLE_TEST BIT(0) +#define AT803X_CDT_STATUS 0x1c +#define AT803X_CDT_STATUS_STAT_NORMAL 0 +#define AT803X_CDT_STATUS_STAT_SHORT 1 +#define AT803X_CDT_STATUS_STAT_OPEN 2 +#define AT803X_CDT_STATUS_STAT_FAIL 3 +#define AT803X_CDT_STATUS_STAT_MASK GENMASK(9, 8) +#define AT803X_CDT_STATUS_DELTA_TIME_MASK GENMASK(7, 0) +#define AT803X_LED_CONTROL 0x18 + +#define AT803X_PHY_MMD3_WOL_CTRL 0x8012 +#define AT803X_WOL_EN BIT(5) +#define AT803X_LOC_MAC_ADDR_0_15_OFFSET 0x804C +#define AT803X_LOC_MAC_ADDR_16_31_OFFSET 0x804B +#define AT803X_LOC_MAC_ADDR_32_47_OFFSET 0x804A +#define AT803X_REG_CHIP_CONFIG 0x1f +#define AT803X_BT_BX_REG_SEL 0x8000 + +#define AT803X_DEBUG_ADDR 0x1D +#define AT803X_DEBUG_DATA 0x1E + +#define AT803X_MODE_CFG_MASK 0x0F +#define AT803X_MODE_CFG_BASET_RGMII 0x00 +#define AT803X_MODE_CFG_BASET_SGMII 0x01 +#define AT803X_MODE_CFG_BX1000_RGMII_50OHM 0x02 +#define AT803X_MODE_CFG_BX1000_RGMII_75OHM 0x03 +#define AT803X_MODE_CFG_BX1000_CONV_50OHM 0x04 +#define AT803X_MODE_CFG_BX1000_CONV_75OHM 0x05 +#define AT803X_MODE_CFG_FX100_RGMII_50OHM 0x06 +#define AT803X_MODE_CFG_FX100_CONV_50OHM 0x07 +#define AT803X_MODE_CFG_RGMII_AUTO_MDET 0x0B +#define AT803X_MODE_CFG_FX100_RGMII_75OHM 0x0E +#define AT803X_MODE_CFG_FX100_CONV_75OHM 0x0F + +#define AT803X_PSSR 0x11 /*PHY-Specific Status Register*/ +#define AT803X_PSSR_MR_AN_COMPLETE 0x0200 + +#define AT803X_DEBUG_ANALOG_TEST_CTRL 0x00 +#define QCA8327_DEBUG_MANU_CTRL_EN BIT(2) +#define QCA8337_DEBUG_MANU_CTRL_EN GENMASK(3, 2) +#define AT803X_DEBUG_RX_CLK_DLY_EN BIT(15) + +#define AT803X_DEBUG_SYSTEM_CTRL_MODE 0x05 +#define AT803X_DEBUG_TX_CLK_DLY_EN BIT(8) + +#define AT803X_DEBUG_REG_HIB_CTRL 0x0b +#define AT803X_DEBUG_HIB_CTRL_SEL_RST_80U BIT(10) +#define AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE BIT(13) +#define AT803X_DEBUG_HIB_CTRL_PS_HIB_EN BIT(15) + +#define AT803X_DEBUG_REG_3C 0x3C + +#define AT803X_DEBUG_REG_GREEN 0x3D +#define AT803X_DEBUG_GATE_CLK_IN1000 BIT(6) + +#define AT803X_DEBUG_REG_1F 0x1F +#define AT803X_DEBUG_PLL_ON BIT(2) +#define AT803X_DEBUG_RGMII_1V8 BIT(3) + +#define MDIO_AZ_DEBUG 0x800D + +/* AT803x supports either the XTAL input pad, an internal PLL or the + * DSP as clock reference for the clock output pad. The XTAL reference + * is only used for 25 MHz output, all other frequencies need the PLL. + * The DSP as a clock reference is used in synchronous ethernet + * applications. + * + * By default the PLL is only enabled if there is a link. Otherwise + * the PHY will go into low power state and disabled the PLL. You can + * set the PLL_ON bit (see debug register 0x1f) to keep the PLL always + * enabled. + */ +#define AT803X_MMD7_CLK25M 0x8016 +#define AT803X_CLK_OUT_MASK GENMASK(4, 2) +#define AT803X_CLK_OUT_25MHZ_XTAL 0 +#define AT803X_CLK_OUT_25MHZ_DSP 1 +#define AT803X_CLK_OUT_50MHZ_PLL 2 +#define AT803X_CLK_OUT_50MHZ_DSP 3 +#define AT803X_CLK_OUT_62_5MHZ_PLL 4 +#define AT803X_CLK_OUT_62_5MHZ_DSP 5 +#define AT803X_CLK_OUT_125MHZ_PLL 6 +#define AT803X_CLK_OUT_125MHZ_DSP 7 + +/* The AR8035 has another mask which is compatible with the AR8031/AR8033 mask + * but doesn't support choosing between XTAL/PLL and DSP. + */ +#define AT8035_CLK_OUT_MASK GENMASK(4, 3) + +#define AT803X_CLK_OUT_STRENGTH_MASK GENMASK(8, 7) +#define AT803X_CLK_OUT_STRENGTH_FULL 0 +#define AT803X_CLK_OUT_STRENGTH_HALF 1 +#define AT803X_CLK_OUT_STRENGTH_QUARTER 2 + +#define AT803X_DEFAULT_DOWNSHIFT 5 +#define AT803X_MIN_DOWNSHIFT 2 +#define AT803X_MAX_DOWNSHIFT 9 + +#define AT803X_MMD3_SMARTEEE_CTL1 0x805b +#define AT803X_MMD3_SMARTEEE_CTL2 0x805c +#define AT803X_MMD3_SMARTEEE_CTL3 0x805d +#define AT803X_MMD3_SMARTEEE_CTL3_LPI_EN BIT(8) + +#define ATH9331_PHY_ID 0x004dd041 +#define ATH8030_PHY_ID 0x004dd076 +#define ATH8031_PHY_ID 0x004dd074 +#define ATH8032_PHY_ID 0x004dd023 +#define ATH8035_PHY_ID 0x004dd072 +#define AT8030_PHY_ID_MASK 0xffffffef + +#define QCA8081_PHY_ID 0x004dd101 + +#define QCA8327_A_PHY_ID 0x004dd033 +#define QCA8327_B_PHY_ID 0x004dd034 +#define QCA8337_PHY_ID 0x004dd036 +#define QCA9561_PHY_ID 0x004dd042 +#define QCA8K_PHY_ID_MASK 0xffffffff + +#define QCA8K_DEVFLAGS_REVISION_MASK GENMASK(2, 0) + +#define AT803X_PAGE_FIBER 0 +#define AT803X_PAGE_COPPER 1 + +/* don't turn off internal PLL */ +#define AT803X_KEEP_PLL_ENABLED BIT(0) +#define AT803X_DISABLE_SMARTEEE BIT(1) + +/* disable hibernation mode */ +#define AT803X_DISABLE_HIBERNATION_MODE BIT(2) + +/* ADC threshold */ +#define QCA808X_PHY_DEBUG_ADC_THRESHOLD 0x2c80 +#define QCA808X_ADC_THRESHOLD_MASK GENMASK(7, 0) +#define QCA808X_ADC_THRESHOLD_80MV 0 +#define QCA808X_ADC_THRESHOLD_100MV 0xf0 +#define QCA808X_ADC_THRESHOLD_200MV 0x0f +#define QCA808X_ADC_THRESHOLD_300MV 0xff + +/* CLD control */ +#define QCA808X_PHY_MMD3_ADDR_CLD_CTRL7 0x8007 +#define QCA808X_8023AZ_AFE_CTRL_MASK GENMASK(8, 4) +#define QCA808X_8023AZ_AFE_EN 0x90 + +/* AZ control */ +#define QCA808X_PHY_MMD3_AZ_TRAINING_CTRL 0x8008 +#define QCA808X_MMD3_AZ_TRAINING_VAL 0x1c32 + +#define QCA808X_PHY_MMD1_MSE_THRESHOLD_20DB 0x8014 +#define QCA808X_MSE_THRESHOLD_20DB_VALUE 0x529 + +#define QCA808X_PHY_MMD1_MSE_THRESHOLD_17DB 0x800E +#define QCA808X_MSE_THRESHOLD_17DB_VALUE 0x341 + +#define QCA808X_PHY_MMD1_MSE_THRESHOLD_27DB 0x801E +#define QCA808X_MSE_THRESHOLD_27DB_VALUE 0x419 + +#define QCA808X_PHY_MMD1_MSE_THRESHOLD_28DB 0x8020 +#define QCA808X_MSE_THRESHOLD_28DB_VALUE 0x341 + +#define QCA808X_PHY_MMD7_TOP_OPTION1 0x901c +#define QCA808X_TOP_OPTION1_DATA 0x0 + +#define QCA808X_PHY_MMD3_DEBUG_1 0xa100 +#define QCA808X_MMD3_DEBUG_1_VALUE 0x9203 +#define QCA808X_PHY_MMD3_DEBUG_2 0xa101 +#define QCA808X_MMD3_DEBUG_2_VALUE 0x48ad +#define QCA808X_PHY_MMD3_DEBUG_3 0xa103 +#define QCA808X_MMD3_DEBUG_3_VALUE 0x1698 +#define QCA808X_PHY_MMD3_DEBUG_4 0xa105 +#define QCA808X_MMD3_DEBUG_4_VALUE 0x8001 +#define QCA808X_PHY_MMD3_DEBUG_5 0xa106 +#define QCA808X_MMD3_DEBUG_5_VALUE 0x1111 +#define QCA808X_PHY_MMD3_DEBUG_6 0xa011 +#define QCA808X_MMD3_DEBUG_6_VALUE 0x5f85 + +/* master/slave seed config */ +#define QCA808X_PHY_DEBUG_LOCAL_SEED 9 +#define QCA808X_MASTER_SLAVE_SEED_ENABLE BIT(1) +#define QCA808X_MASTER_SLAVE_SEED_CFG GENMASK(12, 2) +#define QCA808X_MASTER_SLAVE_SEED_RANGE 0x32 + +/* Hibernation yields lower power consumpiton in contrast with normal operation mode. + * when the copper cable is unplugged, the PHY enters into hibernation mode in about 10s. + */ +#define QCA808X_DBG_AN_TEST 0xb +#define QCA808X_HIBERNATION_EN BIT(15) + +#define QCA808X_CDT_ENABLE_TEST BIT(15) +#define QCA808X_CDT_INTER_CHECK_DIS BIT(13) +#define QCA808X_CDT_LENGTH_UNIT BIT(10) + +#define QCA808X_MMD3_CDT_STATUS 0x8064 +#define QCA808X_MMD3_CDT_DIAG_PAIR_A 0x8065 +#define QCA808X_MMD3_CDT_DIAG_PAIR_B 0x8066 +#define QCA808X_MMD3_CDT_DIAG_PAIR_C 0x8067 +#define QCA808X_MMD3_CDT_DIAG_PAIR_D 0x8068 +#define QCA808X_CDT_DIAG_LENGTH GENMASK(7, 0) + +#define QCA808X_CDT_CODE_PAIR_A GENMASK(15, 12) +#define QCA808X_CDT_CODE_PAIR_B GENMASK(11, 8) +#define QCA808X_CDT_CODE_PAIR_C GENMASK(7, 4) +#define QCA808X_CDT_CODE_PAIR_D GENMASK(3, 0) +#define QCA808X_CDT_STATUS_STAT_FAIL 0 +#define QCA808X_CDT_STATUS_STAT_NORMAL 1 +#define QCA808X_CDT_STATUS_STAT_OPEN 2 +#define QCA808X_CDT_STATUS_STAT_SHORT 3 + +MODULE_DESCRIPTION("Qualcomm Atheros AR803x and QCA808X PHY driver"); +MODULE_AUTHOR("Matus Ujhelyi"); +MODULE_LICENSE("GPL"); + +enum stat_access_type { + PHY, + MMD +}; + +struct at803x_hw_stat { + const char *string; + u8 reg; + u32 mask; + enum stat_access_type access_type; +}; + +static struct at803x_hw_stat at803x_hw_stats[] = { + { "phy_idle_errors", 0xa, GENMASK(7, 0), PHY}, + { "phy_receive_errors", 0x15, GENMASK(15, 0), PHY}, + { "eee_wake_errors", 0x16, GENMASK(15, 0), MMD}, +}; + +struct at803x_priv { + int flags; + u16 clk_25m_reg; + u16 clk_25m_mask; + u8 smarteee_lpi_tw_1g; + u8 smarteee_lpi_tw_100m; + bool is_fiber; + bool is_1000basex; + struct regulator_dev *vddio_rdev; + struct regulator_dev *vddh_rdev; + u64 stats[ARRAY_SIZE(at803x_hw_stats)]; +}; + +struct at803x_context { + u16 bmcr; + u16 advertise; + u16 control1000; + u16 int_enable; + u16 smart_speed; + u16 led_control; +}; + +static int at803x_debug_reg_write(struct phy_device *phydev, u16 reg, u16 data) +{ + int ret; + + ret = phy_write(phydev, AT803X_DEBUG_ADDR, reg); + if (ret < 0) + return ret; + + return phy_write(phydev, AT803X_DEBUG_DATA, data); +} + +static int at803x_debug_reg_read(struct phy_device *phydev, u16 reg) +{ + int ret; + + ret = phy_write(phydev, AT803X_DEBUG_ADDR, reg); + if (ret < 0) + return ret; + + return phy_read(phydev, AT803X_DEBUG_DATA); +} + +static int at803x_debug_reg_mask(struct phy_device *phydev, u16 reg, + u16 clear, u16 set) +{ + u16 val; + int ret; + + ret = at803x_debug_reg_read(phydev, reg); + if (ret < 0) + return ret; + + val = ret & 0xffff; + val &= ~clear; + val |= set; + + return phy_write(phydev, AT803X_DEBUG_DATA, val); +} + +static int at803x_write_page(struct phy_device *phydev, int page) +{ + int mask; + int set; + + if (page == AT803X_PAGE_COPPER) { + set = AT803X_BT_BX_REG_SEL; + mask = 0; + } else { + set = 0; + mask = AT803X_BT_BX_REG_SEL; + } + + return __phy_modify(phydev, AT803X_REG_CHIP_CONFIG, mask, set); +} + +static int at803x_read_page(struct phy_device *phydev) +{ + int ccr = __phy_read(phydev, AT803X_REG_CHIP_CONFIG); + + if (ccr < 0) + return ccr; + + if (ccr & AT803X_BT_BX_REG_SEL) + return AT803X_PAGE_COPPER; + + return AT803X_PAGE_FIBER; +} + +static int at803x_enable_rx_delay(struct phy_device *phydev) +{ + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, 0, + AT803X_DEBUG_RX_CLK_DLY_EN); +} + +static int at803x_enable_tx_delay(struct phy_device *phydev) +{ + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, 0, + AT803X_DEBUG_TX_CLK_DLY_EN); +} + +static int at803x_disable_rx_delay(struct phy_device *phydev) +{ + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, + AT803X_DEBUG_RX_CLK_DLY_EN, 0); +} + +static int at803x_disable_tx_delay(struct phy_device *phydev) +{ + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, + AT803X_DEBUG_TX_CLK_DLY_EN, 0); +} + +/* save relevant PHY registers to private copy */ +static void at803x_context_save(struct phy_device *phydev, + struct at803x_context *context) +{ + context->bmcr = phy_read(phydev, MII_BMCR); + context->advertise = phy_read(phydev, MII_ADVERTISE); + context->control1000 = phy_read(phydev, MII_CTRL1000); + context->int_enable = phy_read(phydev, AT803X_INTR_ENABLE); + context->smart_speed = phy_read(phydev, AT803X_SMART_SPEED); + context->led_control = phy_read(phydev, AT803X_LED_CONTROL); +} + +/* restore relevant PHY registers from private copy */ +static void at803x_context_restore(struct phy_device *phydev, + const struct at803x_context *context) +{ + phy_write(phydev, MII_BMCR, context->bmcr); + phy_write(phydev, MII_ADVERTISE, context->advertise); + phy_write(phydev, MII_CTRL1000, context->control1000); + phy_write(phydev, AT803X_INTR_ENABLE, context->int_enable); + phy_write(phydev, AT803X_SMART_SPEED, context->smart_speed); + phy_write(phydev, AT803X_LED_CONTROL, context->led_control); +} + +static int at803x_set_wol(struct phy_device *phydev, + struct ethtool_wolinfo *wol) +{ + int ret, irq_enabled; + + if (wol->wolopts & WAKE_MAGIC) { + struct net_device *ndev = phydev->attached_dev; + const u8 *mac; + unsigned int i; + static const unsigned int offsets[] = { + AT803X_LOC_MAC_ADDR_32_47_OFFSET, + AT803X_LOC_MAC_ADDR_16_31_OFFSET, + AT803X_LOC_MAC_ADDR_0_15_OFFSET, + }; + + if (!ndev) + return -ENODEV; + + mac = (const u8 *) ndev->dev_addr; + + if (!is_valid_ether_addr(mac)) + return -EINVAL; + + for (i = 0; i < 3; i++) + phy_write_mmd(phydev, MDIO_MMD_PCS, offsets[i], + mac[(i * 2) + 1] | (mac[(i * 2)] << 8)); + + /* Enable WOL function for 1588 */ + if (phydev->drv->phy_id == ATH8031_PHY_ID) { + ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, + AT803X_PHY_MMD3_WOL_CTRL, + 0, AT803X_WOL_EN); + if (ret) + return ret; + } + /* Enable WOL interrupt */ + ret = phy_modify(phydev, AT803X_INTR_ENABLE, 0, AT803X_INTR_ENABLE_WOL); + if (ret) + return ret; + } else { + /* Disable WoL function for 1588 */ + if (phydev->drv->phy_id == ATH8031_PHY_ID) { + ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, + AT803X_PHY_MMD3_WOL_CTRL, + AT803X_WOL_EN, 0); + if (ret) + return ret; + } + /* Disable WOL interrupt */ + ret = phy_modify(phydev, AT803X_INTR_ENABLE, AT803X_INTR_ENABLE_WOL, 0); + if (ret) + return ret; + } + + /* Clear WOL status */ + ret = phy_read(phydev, AT803X_INTR_STATUS); + if (ret < 0) + return ret; + + /* Check if there are other interrupts except for WOL triggered when PHY is + * in interrupt mode, only the interrupts enabled by AT803X_INTR_ENABLE can + * be passed up to the interrupt PIN. + */ + irq_enabled = phy_read(phydev, AT803X_INTR_ENABLE); + if (irq_enabled < 0) + return irq_enabled; + + irq_enabled &= ~AT803X_INTR_ENABLE_WOL; + if (ret & irq_enabled && !phy_polling_mode(phydev)) + phy_trigger_machine(phydev); + + return 0; +} + +static void at803x_get_wol(struct phy_device *phydev, + struct ethtool_wolinfo *wol) +{ + int value; + + wol->supported = WAKE_MAGIC; + wol->wolopts = 0; + + value = phy_read(phydev, AT803X_INTR_ENABLE); + if (value < 0) + return; + + if (value & AT803X_INTR_ENABLE_WOL) + wol->wolopts |= WAKE_MAGIC; +} + +static int at803x_get_sset_count(struct phy_device *phydev) +{ + return ARRAY_SIZE(at803x_hw_stats); +} + +static void at803x_get_strings(struct phy_device *phydev, u8 *data) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(at803x_hw_stats); i++) { + strscpy(data + i * ETH_GSTRING_LEN, + at803x_hw_stats[i].string, ETH_GSTRING_LEN); + } +} + +static u64 at803x_get_stat(struct phy_device *phydev, int i) +{ + struct at803x_hw_stat stat = at803x_hw_stats[i]; + struct at803x_priv *priv = phydev->priv; + int val; + u64 ret; + + if (stat.access_type == MMD) + val = phy_read_mmd(phydev, MDIO_MMD_PCS, stat.reg); + else + val = phy_read(phydev, stat.reg); + + if (val < 0) { + ret = U64_MAX; + } else { + val = val & stat.mask; + priv->stats[i] += val; + ret = priv->stats[i]; + } + + return ret; +} + +static void at803x_get_stats(struct phy_device *phydev, + struct ethtool_stats *stats, u64 *data) +{ + int i; + + for (i = 0; i < ARRAY_SIZE(at803x_hw_stats); i++) + data[i] = at803x_get_stat(phydev, i); +} + +static int at803x_suspend(struct phy_device *phydev) +{ + int value; + int wol_enabled; + + value = phy_read(phydev, AT803X_INTR_ENABLE); + wol_enabled = value & AT803X_INTR_ENABLE_WOL; + + if (wol_enabled) + value = BMCR_ISOLATE; + else + value = BMCR_PDOWN; + + phy_modify(phydev, MII_BMCR, 0, value); + + return 0; +} + +static int at803x_resume(struct phy_device *phydev) +{ + return phy_modify(phydev, MII_BMCR, BMCR_PDOWN | BMCR_ISOLATE, 0); +} + +static int at803x_rgmii_reg_set_voltage_sel(struct regulator_dev *rdev, + unsigned int selector) +{ + struct phy_device *phydev = rdev_get_drvdata(rdev); + + if (selector) + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F, + 0, AT803X_DEBUG_RGMII_1V8); + else + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F, + AT803X_DEBUG_RGMII_1V8, 0); +} + +static int at803x_rgmii_reg_get_voltage_sel(struct regulator_dev *rdev) +{ + struct phy_device *phydev = rdev_get_drvdata(rdev); + int val; + + val = at803x_debug_reg_read(phydev, AT803X_DEBUG_REG_1F); + if (val < 0) + return val; + + return (val & AT803X_DEBUG_RGMII_1V8) ? 1 : 0; +} + +static const struct regulator_ops vddio_regulator_ops = { + .list_voltage = regulator_list_voltage_table, + .set_voltage_sel = at803x_rgmii_reg_set_voltage_sel, + .get_voltage_sel = at803x_rgmii_reg_get_voltage_sel, +}; + +static const unsigned int vddio_voltage_table[] = { + 1500000, + 1800000, +}; + +static const struct regulator_desc vddio_desc = { + .name = "vddio", + .of_match = of_match_ptr("vddio-regulator"), + .n_voltages = ARRAY_SIZE(vddio_voltage_table), + .volt_table = vddio_voltage_table, + .ops = &vddio_regulator_ops, + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, +}; + +static const struct regulator_ops vddh_regulator_ops = { +}; + +static const struct regulator_desc vddh_desc = { + .name = "vddh", + .of_match = of_match_ptr("vddh-regulator"), + .n_voltages = 1, + .fixed_uV = 2500000, + .ops = &vddh_regulator_ops, + .type = REGULATOR_VOLTAGE, + .owner = THIS_MODULE, +}; + +static int at8031_register_regulators(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + struct device *dev = &phydev->mdio.dev; + struct regulator_config config = { }; + + config.dev = dev; + config.driver_data = phydev; + + priv->vddio_rdev = devm_regulator_register(dev, &vddio_desc, &config); + if (IS_ERR(priv->vddio_rdev)) { + phydev_err(phydev, "failed to register VDDIO regulator\n"); + return PTR_ERR(priv->vddio_rdev); + } + + priv->vddh_rdev = devm_regulator_register(dev, &vddh_desc, &config); + if (IS_ERR(priv->vddh_rdev)) { + phydev_err(phydev, "failed to register VDDH regulator\n"); + return PTR_ERR(priv->vddh_rdev); + } + + return 0; +} + +static int at803x_sfp_insert(void *upstream, const struct sfp_eeprom_id *id) +{ + struct phy_device *phydev = upstream; + __ETHTOOL_DECLARE_LINK_MODE_MASK(phy_support); + __ETHTOOL_DECLARE_LINK_MODE_MASK(sfp_support); + DECLARE_PHY_INTERFACE_MASK(interfaces); + phy_interface_t iface; + + linkmode_zero(phy_support); + phylink_set(phy_support, 1000baseX_Full); + phylink_set(phy_support, 1000baseT_Full); + phylink_set(phy_support, Autoneg); + phylink_set(phy_support, Pause); + phylink_set(phy_support, Asym_Pause); + + linkmode_zero(sfp_support); + sfp_parse_support(phydev->sfp_bus, id, sfp_support, interfaces); + /* Some modules support 10G modes as well as others we support. + * Mask out non-supported modes so the correct interface is picked. + */ + linkmode_and(sfp_support, phy_support, sfp_support); + + if (linkmode_empty(sfp_support)) { + dev_err(&phydev->mdio.dev, "incompatible SFP module inserted\n"); + return -EINVAL; + } + + iface = sfp_select_interface(phydev->sfp_bus, sfp_support); + + /* Only 1000Base-X is supported by AR8031/8033 as the downstream SerDes + * interface for use with SFP modules. + * However, some copper modules detected as having a preferred SGMII + * interface do default to and function in 1000Base-X mode, so just + * print a warning and allow such modules, as they may have some chance + * of working. + */ + if (iface == PHY_INTERFACE_MODE_SGMII) + dev_warn(&phydev->mdio.dev, "module may not function if 1000Base-X not supported\n"); + else if (iface != PHY_INTERFACE_MODE_1000BASEX) + return -EINVAL; + + return 0; +} + +static const struct sfp_upstream_ops at803x_sfp_ops = { + .attach = phy_sfp_attach, + .detach = phy_sfp_detach, + .module_insert = at803x_sfp_insert, +}; + +static int at803x_parse_dt(struct phy_device *phydev) +{ + struct device_node *node = phydev->mdio.dev.of_node; + struct at803x_priv *priv = phydev->priv; + u32 freq, strength, tw; + unsigned int sel; + int ret; + + if (!IS_ENABLED(CONFIG_OF_MDIO)) + return 0; + + if (of_property_read_bool(node, "qca,disable-smarteee")) + priv->flags |= AT803X_DISABLE_SMARTEEE; + + if (of_property_read_bool(node, "qca,disable-hibernation-mode")) + priv->flags |= AT803X_DISABLE_HIBERNATION_MODE; + + if (!of_property_read_u32(node, "qca,smarteee-tw-us-1g", &tw)) { + if (!tw || tw > 255) { + phydev_err(phydev, "invalid qca,smarteee-tw-us-1g\n"); + return -EINVAL; + } + priv->smarteee_lpi_tw_1g = tw; + } + + if (!of_property_read_u32(node, "qca,smarteee-tw-us-100m", &tw)) { + if (!tw || tw > 255) { + phydev_err(phydev, "invalid qca,smarteee-tw-us-100m\n"); + return -EINVAL; + } + priv->smarteee_lpi_tw_100m = tw; + } + + ret = of_property_read_u32(node, "qca,clk-out-frequency", &freq); + if (!ret) { + switch (freq) { + case 25000000: + sel = AT803X_CLK_OUT_25MHZ_XTAL; + break; + case 50000000: + sel = AT803X_CLK_OUT_50MHZ_PLL; + break; + case 62500000: + sel = AT803X_CLK_OUT_62_5MHZ_PLL; + break; + case 125000000: + sel = AT803X_CLK_OUT_125MHZ_PLL; + break; + default: + phydev_err(phydev, "invalid qca,clk-out-frequency\n"); + return -EINVAL; + } + + priv->clk_25m_reg |= FIELD_PREP(AT803X_CLK_OUT_MASK, sel); + priv->clk_25m_mask |= AT803X_CLK_OUT_MASK; + + /* Fixup for the AR8030/AR8035. This chip has another mask and + * doesn't support the DSP reference. Eg. the lowest bit of the + * mask. The upper two bits select the same frequencies. Mask + * the lowest bit here. + * + * Warning: + * There was no datasheet for the AR8030 available so this is + * just a guess. But the AR8035 is listed as pin compatible + * to the AR8030 so there might be a good chance it works on + * the AR8030 too. + */ + if (phydev->drv->phy_id == ATH8030_PHY_ID || + phydev->drv->phy_id == ATH8035_PHY_ID) { + priv->clk_25m_reg &= AT8035_CLK_OUT_MASK; + priv->clk_25m_mask &= AT8035_CLK_OUT_MASK; + } + } + + ret = of_property_read_u32(node, "qca,clk-out-strength", &strength); + if (!ret) { + priv->clk_25m_mask |= AT803X_CLK_OUT_STRENGTH_MASK; + switch (strength) { + case AR803X_STRENGTH_FULL: + priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_FULL; + break; + case AR803X_STRENGTH_HALF: + priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_HALF; + break; + case AR803X_STRENGTH_QUARTER: + priv->clk_25m_reg |= AT803X_CLK_OUT_STRENGTH_QUARTER; + break; + default: + phydev_err(phydev, "invalid qca,clk-out-strength\n"); + return -EINVAL; + } + } + + /* Only supported on AR8031/AR8033, the AR8030/AR8035 use strapping + * options. + */ + if (phydev->drv->phy_id == ATH8031_PHY_ID) { + if (of_property_read_bool(node, "qca,keep-pll-enabled")) + priv->flags |= AT803X_KEEP_PLL_ENABLED; + + ret = at8031_register_regulators(phydev); + if (ret < 0) + return ret; + + ret = devm_regulator_get_enable_optional(&phydev->mdio.dev, + "vddio"); + if (ret) { + phydev_err(phydev, "failed to get VDDIO regulator\n"); + return ret; + } + + /* Only AR8031/8033 support 1000Base-X for SFP modules */ + ret = phy_sfp_probe(phydev, &at803x_sfp_ops); + if (ret < 0) + return ret; + } + + return 0; +} + +static int at803x_probe(struct phy_device *phydev) +{ + struct device *dev = &phydev->mdio.dev; + struct at803x_priv *priv; + int ret; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + phydev->priv = priv; + + ret = at803x_parse_dt(phydev); + if (ret) + return ret; + + if (phydev->drv->phy_id == ATH8031_PHY_ID) { + int ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG); + int mode_cfg; + + if (ccr < 0) + return ccr; + mode_cfg = ccr & AT803X_MODE_CFG_MASK; + + switch (mode_cfg) { + case AT803X_MODE_CFG_BX1000_RGMII_50OHM: + case AT803X_MODE_CFG_BX1000_RGMII_75OHM: + priv->is_1000basex = true; + fallthrough; + case AT803X_MODE_CFG_FX100_RGMII_50OHM: + case AT803X_MODE_CFG_FX100_RGMII_75OHM: + priv->is_fiber = true; + break; + } + + /* Disable WoL in 1588 register which is enabled + * by default + */ + ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, + AT803X_PHY_MMD3_WOL_CTRL, + AT803X_WOL_EN, 0); + if (ret) + return ret; + } + + return 0; +} + +static int at803x_get_features(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + int err; + + err = genphy_read_abilities(phydev); + if (err) + return err; + + if (phydev->drv->phy_id == QCA8081_PHY_ID) { + err = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MDIO_PMA_NG_EXTABLE); + if (err < 0) + return err; + + linkmode_mod_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->supported, + err & MDIO_PMA_NG_EXTABLE_2_5GBT); + } + + if (phydev->drv->phy_id != ATH8031_PHY_ID) + return 0; + + /* AR8031/AR8033 have different status registers + * for copper and fiber operation. However, the + * extended status register is the same for both + * operation modes. + * + * As a result of that, ESTATUS_1000_XFULL is set + * to 1 even when operating in copper TP mode. + * + * Remove this mode from the supported link modes + * when not operating in 1000BaseX mode. + */ + if (!priv->is_1000basex) + linkmode_clear_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT, + phydev->supported); + + return 0; +} + +static int at803x_smarteee_config(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + u16 mask = 0, val = 0; + int ret; + + if (priv->flags & AT803X_DISABLE_SMARTEEE) + return phy_modify_mmd(phydev, MDIO_MMD_PCS, + AT803X_MMD3_SMARTEEE_CTL3, + AT803X_MMD3_SMARTEEE_CTL3_LPI_EN, 0); + + if (priv->smarteee_lpi_tw_1g) { + mask |= 0xff00; + val |= priv->smarteee_lpi_tw_1g << 8; + } + if (priv->smarteee_lpi_tw_100m) { + mask |= 0x00ff; + val |= priv->smarteee_lpi_tw_100m; + } + if (!mask) + return 0; + + ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, AT803X_MMD3_SMARTEEE_CTL1, + mask, val); + if (ret) + return ret; + + return phy_modify_mmd(phydev, MDIO_MMD_PCS, AT803X_MMD3_SMARTEEE_CTL3, + AT803X_MMD3_SMARTEEE_CTL3_LPI_EN, + AT803X_MMD3_SMARTEEE_CTL3_LPI_EN); +} + +static int at803x_clk_out_config(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + + if (!priv->clk_25m_mask) + return 0; + + return phy_modify_mmd(phydev, MDIO_MMD_AN, AT803X_MMD7_CLK25M, + priv->clk_25m_mask, priv->clk_25m_reg); +} + +static int at8031_pll_config(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + + /* The default after hardware reset is PLL OFF. After a soft reset, the + * values are retained. + */ + if (priv->flags & AT803X_KEEP_PLL_ENABLED) + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F, + 0, AT803X_DEBUG_PLL_ON); + else + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_1F, + AT803X_DEBUG_PLL_ON, 0); +} + +static int at803x_hibernation_mode_config(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + + /* The default after hardware reset is hibernation mode enabled. After + * software reset, the value is retained. + */ + if (!(priv->flags & AT803X_DISABLE_HIBERNATION_MODE)) + return 0; + + return at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_HIB_CTRL, + AT803X_DEBUG_HIB_CTRL_PS_HIB_EN, 0); +} + +static int at803x_config_init(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + int ret; + + if (phydev->drv->phy_id == ATH8031_PHY_ID) { + /* Some bootloaders leave the fiber page selected. + * Switch to the appropriate page (fiber or copper), as otherwise we + * read the PHY capabilities from the wrong page. + */ + phy_lock_mdio_bus(phydev); + ret = at803x_write_page(phydev, + priv->is_fiber ? AT803X_PAGE_FIBER : + AT803X_PAGE_COPPER); + phy_unlock_mdio_bus(phydev); + if (ret) + return ret; + + ret = at8031_pll_config(phydev); + if (ret < 0) + return ret; + } + + /* The RX and TX delay default is: + * after HW reset: RX delay enabled and TX delay disabled + * after SW reset: RX delay enabled, while TX delay retains the + * value before reset. + */ + if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID || + phydev->interface == PHY_INTERFACE_MODE_RGMII_RXID) + ret = at803x_enable_rx_delay(phydev); + else + ret = at803x_disable_rx_delay(phydev); + if (ret < 0) + return ret; + + if (phydev->interface == PHY_INTERFACE_MODE_RGMII_ID || + phydev->interface == PHY_INTERFACE_MODE_RGMII_TXID) + ret = at803x_enable_tx_delay(phydev); + else + ret = at803x_disable_tx_delay(phydev); + if (ret < 0) + return ret; + + ret = at803x_smarteee_config(phydev); + if (ret < 0) + return ret; + + ret = at803x_clk_out_config(phydev); + if (ret < 0) + return ret; + + ret = at803x_hibernation_mode_config(phydev); + if (ret < 0) + return ret; + + /* Ar803x extended next page bit is enabled by default. Cisco + * multigig switches read this bit and attempt to negotiate 10Gbps + * rates even if the next page bit is disabled. This is incorrect + * behaviour but we still need to accommodate it. XNP is only needed + * for 10Gbps support, so disable XNP. + */ + return phy_modify(phydev, MII_ADVERTISE, MDIO_AN_CTRL1_XNP, 0); +} + +static int at803x_ack_interrupt(struct phy_device *phydev) +{ + int err; + + err = phy_read(phydev, AT803X_INTR_STATUS); + + return (err < 0) ? err : 0; +} + +static int at803x_config_intr(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + int err; + int value; + + value = phy_read(phydev, AT803X_INTR_ENABLE); + + if (phydev->interrupts == PHY_INTERRUPT_ENABLED) { + /* Clear any pending interrupts */ + err = at803x_ack_interrupt(phydev); + if (err) + return err; + + value |= AT803X_INTR_ENABLE_AUTONEG_ERR; + value |= AT803X_INTR_ENABLE_SPEED_CHANGED; + value |= AT803X_INTR_ENABLE_DUPLEX_CHANGED; + value |= AT803X_INTR_ENABLE_LINK_FAIL; + value |= AT803X_INTR_ENABLE_LINK_SUCCESS; + if (priv->is_fiber) { + value |= AT803X_INTR_ENABLE_LINK_FAIL_BX; + value |= AT803X_INTR_ENABLE_LINK_SUCCESS_BX; + } + + err = phy_write(phydev, AT803X_INTR_ENABLE, value); + } else { + err = phy_write(phydev, AT803X_INTR_ENABLE, 0); + if (err) + return err; + + /* Clear any pending interrupts */ + err = at803x_ack_interrupt(phydev); + } + + return err; +} + +static irqreturn_t at803x_handle_interrupt(struct phy_device *phydev) +{ + int irq_status, int_enabled; + + irq_status = phy_read(phydev, AT803X_INTR_STATUS); + if (irq_status < 0) { + phy_error(phydev); + return IRQ_NONE; + } + + /* Read the current enabled interrupts */ + int_enabled = phy_read(phydev, AT803X_INTR_ENABLE); + if (int_enabled < 0) { + phy_error(phydev); + return IRQ_NONE; + } + + /* See if this was one of our enabled interrupts */ + if (!(irq_status & int_enabled)) + return IRQ_NONE; + + phy_trigger_machine(phydev); + + return IRQ_HANDLED; +} + +static void at803x_link_change_notify(struct phy_device *phydev) +{ + /* + * Conduct a hardware reset for AT8030 every time a link loss is + * signalled. This is necessary to circumvent a hardware bug that + * occurs when the cable is unplugged while TX packets are pending + * in the FIFO. In such cases, the FIFO enters an error mode it + * cannot recover from by software. + */ + if (phydev->state == PHY_NOLINK && phydev->mdio.reset_gpio) { + struct at803x_context context; + + at803x_context_save(phydev, &context); + + phy_device_reset(phydev, 1); + msleep(1); + phy_device_reset(phydev, 0); + msleep(1); + + at803x_context_restore(phydev, &context); + + phydev_dbg(phydev, "%s(): phy was reset\n", __func__); + } +} + +static int at803x_read_specific_status(struct phy_device *phydev) +{ + int ss; + + /* Read the AT8035 PHY-Specific Status register, which indicates the + * speed and duplex that the PHY is actually using, irrespective of + * whether we are in autoneg mode or not. + */ + ss = phy_read(phydev, AT803X_SPECIFIC_STATUS); + if (ss < 0) + return ss; + + if (ss & AT803X_SS_SPEED_DUPLEX_RESOLVED) { + int sfc, speed; + + sfc = phy_read(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL); + if (sfc < 0) + return sfc; + + /* qca8081 takes the different bits for speed value from at803x */ + if (phydev->drv->phy_id == QCA8081_PHY_ID) + speed = FIELD_GET(QCA808X_SS_SPEED_MASK, ss); + else + speed = FIELD_GET(AT803X_SS_SPEED_MASK, ss); + + switch (speed) { + case AT803X_SS_SPEED_10: + phydev->speed = SPEED_10; + break; + case AT803X_SS_SPEED_100: + phydev->speed = SPEED_100; + break; + case AT803X_SS_SPEED_1000: + phydev->speed = SPEED_1000; + break; + case QCA808X_SS_SPEED_2500: + phydev->speed = SPEED_2500; + break; + } + if (ss & AT803X_SS_DUPLEX) + phydev->duplex = DUPLEX_FULL; + else + phydev->duplex = DUPLEX_HALF; + + if (ss & AT803X_SS_MDIX) + phydev->mdix = ETH_TP_MDI_X; + else + phydev->mdix = ETH_TP_MDI; + + switch (FIELD_GET(AT803X_SFC_MDI_CROSSOVER_MODE_M, sfc)) { + case AT803X_SFC_MANUAL_MDI: + phydev->mdix_ctrl = ETH_TP_MDI; + break; + case AT803X_SFC_MANUAL_MDIX: + phydev->mdix_ctrl = ETH_TP_MDI_X; + break; + case AT803X_SFC_AUTOMATIC_CROSSOVER: + phydev->mdix_ctrl = ETH_TP_MDI_AUTO; + break; + } + } + + return 0; +} + +static int at803x_read_status(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + int err, old_link = phydev->link; + + if (priv->is_1000basex) + return genphy_c37_read_status(phydev); + + /* Update the link, but return if there was an error */ + err = genphy_update_link(phydev); + if (err) + return err; + + /* why bother the PHY if nothing can have changed */ + if (phydev->autoneg == AUTONEG_ENABLE && old_link && phydev->link) + return 0; + + phydev->speed = SPEED_UNKNOWN; + phydev->duplex = DUPLEX_UNKNOWN; + phydev->pause = 0; + phydev->asym_pause = 0; + + err = genphy_read_lpa(phydev); + if (err < 0) + return err; + + err = at803x_read_specific_status(phydev); + if (err < 0) + return err; + + if (phydev->autoneg == AUTONEG_ENABLE && phydev->autoneg_complete) + phy_resolve_aneg_pause(phydev); + + return 0; +} + +static int at803x_config_mdix(struct phy_device *phydev, u8 ctrl) +{ + u16 val; + + switch (ctrl) { + case ETH_TP_MDI: + val = AT803X_SFC_MANUAL_MDI; + break; + case ETH_TP_MDI_X: + val = AT803X_SFC_MANUAL_MDIX; + break; + case ETH_TP_MDI_AUTO: + val = AT803X_SFC_AUTOMATIC_CROSSOVER; + break; + default: + return 0; + } + + return phy_modify_changed(phydev, AT803X_SPECIFIC_FUNCTION_CONTROL, + AT803X_SFC_MDI_CROSSOVER_MODE_M, + FIELD_PREP(AT803X_SFC_MDI_CROSSOVER_MODE_M, val)); +} + +static int at803x_config_aneg(struct phy_device *phydev) +{ + struct at803x_priv *priv = phydev->priv; + int ret; + + ret = at803x_config_mdix(phydev, phydev->mdix_ctrl); + if (ret < 0) + return ret; + + /* Changes of the midx bits are disruptive to the normal operation; + * therefore any changes to these registers must be followed by a + * software reset to take effect. + */ + if (ret == 1) { + ret = genphy_soft_reset(phydev); + if (ret < 0) + return ret; + } + + if (priv->is_1000basex) + return genphy_c37_config_aneg(phydev); + + /* Do not restart auto-negotiation by setting ret to 0 defautly, + * when calling __genphy_config_aneg later. + */ + ret = 0; + + if (phydev->drv->phy_id == QCA8081_PHY_ID) { + int phy_ctrl = 0; + + /* The reg MII_BMCR also needs to be configured for force mode, the + * genphy_config_aneg is also needed. + */ + if (phydev->autoneg == AUTONEG_DISABLE) + genphy_c45_pma_setup_forced(phydev); + + if (linkmode_test_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->advertising)) + phy_ctrl = MDIO_AN_10GBT_CTRL_ADV2_5G; + + ret = phy_modify_mmd_changed(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_CTRL, + MDIO_AN_10GBT_CTRL_ADV2_5G, phy_ctrl); + if (ret < 0) + return ret; + } + + return __genphy_config_aneg(phydev, ret); +} + +static int at803x_get_downshift(struct phy_device *phydev, u8 *d) +{ + int val; + + val = phy_read(phydev, AT803X_SMART_SPEED); + if (val < 0) + return val; + + if (val & AT803X_SMART_SPEED_ENABLE) + *d = FIELD_GET(AT803X_SMART_SPEED_RETRY_LIMIT_MASK, val) + 2; + else + *d = DOWNSHIFT_DEV_DISABLE; + + return 0; +} + +static int at803x_set_downshift(struct phy_device *phydev, u8 cnt) +{ + u16 mask, set; + int ret; + + switch (cnt) { + case DOWNSHIFT_DEV_DEFAULT_COUNT: + cnt = AT803X_DEFAULT_DOWNSHIFT; + fallthrough; + case AT803X_MIN_DOWNSHIFT ... AT803X_MAX_DOWNSHIFT: + set = AT803X_SMART_SPEED_ENABLE | + AT803X_SMART_SPEED_BYPASS_TIMER | + FIELD_PREP(AT803X_SMART_SPEED_RETRY_LIMIT_MASK, cnt - 2); + mask = AT803X_SMART_SPEED_RETRY_LIMIT_MASK; + break; + case DOWNSHIFT_DEV_DISABLE: + set = 0; + mask = AT803X_SMART_SPEED_ENABLE | + AT803X_SMART_SPEED_BYPASS_TIMER; + break; + default: + return -EINVAL; + } + + ret = phy_modify_changed(phydev, AT803X_SMART_SPEED, mask, set); + + /* After changing the smart speed settings, we need to perform a + * software reset, use phy_init_hw() to make sure we set the + * reapply any values which might got lost during software reset. + */ + if (ret == 1) + ret = phy_init_hw(phydev); + + return ret; +} + +static int at803x_get_tunable(struct phy_device *phydev, + struct ethtool_tunable *tuna, void *data) +{ + switch (tuna->id) { + case ETHTOOL_PHY_DOWNSHIFT: + return at803x_get_downshift(phydev, data); + default: + return -EOPNOTSUPP; + } +} + +static int at803x_set_tunable(struct phy_device *phydev, + struct ethtool_tunable *tuna, const void *data) +{ + switch (tuna->id) { + case ETHTOOL_PHY_DOWNSHIFT: + return at803x_set_downshift(phydev, *(const u8 *)data); + default: + return -EOPNOTSUPP; + } +} + +static int at803x_cable_test_result_trans(u16 status) +{ + switch (FIELD_GET(AT803X_CDT_STATUS_STAT_MASK, status)) { + case AT803X_CDT_STATUS_STAT_NORMAL: + return ETHTOOL_A_CABLE_RESULT_CODE_OK; + case AT803X_CDT_STATUS_STAT_SHORT: + return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT; + case AT803X_CDT_STATUS_STAT_OPEN: + return ETHTOOL_A_CABLE_RESULT_CODE_OPEN; + case AT803X_CDT_STATUS_STAT_FAIL: + default: + return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC; + } +} + +static bool at803x_cdt_test_failed(u16 status) +{ + return FIELD_GET(AT803X_CDT_STATUS_STAT_MASK, status) == + AT803X_CDT_STATUS_STAT_FAIL; +} + +static bool at803x_cdt_fault_length_valid(u16 status) +{ + switch (FIELD_GET(AT803X_CDT_STATUS_STAT_MASK, status)) { + case AT803X_CDT_STATUS_STAT_OPEN: + case AT803X_CDT_STATUS_STAT_SHORT: + return true; + } + return false; +} + +static int at803x_cdt_fault_length(u16 status) +{ + int dt; + + /* According to the datasheet the distance to the fault is + * DELTA_TIME * 0.824 meters. + * + * The author suspect the correct formula is: + * + * fault_distance = DELTA_TIME * (c * VF) / 125MHz / 2 + * + * where c is the speed of light, VF is the velocity factor of + * the twisted pair cable, 125MHz the counter frequency and + * we need to divide by 2 because the hardware will measure the + * round trip time to the fault and back to the PHY. + * + * With a VF of 0.69 we get the factor 0.824 mentioned in the + * datasheet. + */ + dt = FIELD_GET(AT803X_CDT_STATUS_DELTA_TIME_MASK, status); + + return (dt * 824) / 10; +} + +static int at803x_cdt_start(struct phy_device *phydev, int pair) +{ + u16 cdt; + + /* qca8081 takes the different bit 15 to enable CDT test */ + if (phydev->drv->phy_id == QCA8081_PHY_ID) + cdt = QCA808X_CDT_ENABLE_TEST | + QCA808X_CDT_LENGTH_UNIT | + QCA808X_CDT_INTER_CHECK_DIS; + else + cdt = FIELD_PREP(AT803X_CDT_MDI_PAIR_MASK, pair) | + AT803X_CDT_ENABLE_TEST; + + return phy_write(phydev, AT803X_CDT, cdt); +} + +static int at803x_cdt_wait_for_completion(struct phy_device *phydev) +{ + int val, ret; + u16 cdt_en; + + if (phydev->drv->phy_id == QCA8081_PHY_ID) + cdt_en = QCA808X_CDT_ENABLE_TEST; + else + cdt_en = AT803X_CDT_ENABLE_TEST; + + /* One test run takes about 25ms */ + ret = phy_read_poll_timeout(phydev, AT803X_CDT, val, + !(val & cdt_en), + 30000, 100000, true); + + return ret < 0 ? ret : 0; +} + +static int at803x_cable_test_one_pair(struct phy_device *phydev, int pair) +{ + static const int ethtool_pair[] = { + ETHTOOL_A_CABLE_PAIR_A, + ETHTOOL_A_CABLE_PAIR_B, + ETHTOOL_A_CABLE_PAIR_C, + ETHTOOL_A_CABLE_PAIR_D, + }; + int ret, val; + + ret = at803x_cdt_start(phydev, pair); + if (ret) + return ret; + + ret = at803x_cdt_wait_for_completion(phydev); + if (ret) + return ret; + + val = phy_read(phydev, AT803X_CDT_STATUS); + if (val < 0) + return val; + + if (at803x_cdt_test_failed(val)) + return 0; + + ethnl_cable_test_result(phydev, ethtool_pair[pair], + at803x_cable_test_result_trans(val)); + + if (at803x_cdt_fault_length_valid(val)) + ethnl_cable_test_fault_length(phydev, ethtool_pair[pair], + at803x_cdt_fault_length(val)); + + return 1; +} + +static int at803x_cable_test_get_status(struct phy_device *phydev, + bool *finished) +{ + unsigned long pair_mask; + int retries = 20; + int pair, ret; + + if (phydev->phy_id == ATH9331_PHY_ID || + phydev->phy_id == ATH8032_PHY_ID || + phydev->phy_id == QCA9561_PHY_ID) + pair_mask = 0x3; + else + pair_mask = 0xf; + + *finished = false; + + /* According to the datasheet the CDT can be performed when + * there is no link partner or when the link partner is + * auto-negotiating. Starting the test will restart the AN + * automatically. It seems that doing this repeatedly we will + * get a slot where our link partner won't disturb our + * measurement. + */ + while (pair_mask && retries--) { + for_each_set_bit(pair, &pair_mask, 4) { + ret = at803x_cable_test_one_pair(phydev, pair); + if (ret < 0) + return ret; + if (ret) + clear_bit(pair, &pair_mask); + } + if (pair_mask) + msleep(250); + } + + *finished = true; + + return 0; +} + +static int at803x_cable_test_start(struct phy_device *phydev) +{ + /* Enable auto-negotiation, but advertise no capabilities, no link + * will be established. A restart of the auto-negotiation is not + * required, because the cable test will automatically break the link. + */ + phy_write(phydev, MII_BMCR, BMCR_ANENABLE); + phy_write(phydev, MII_ADVERTISE, ADVERTISE_CSMA); + if (phydev->phy_id != ATH9331_PHY_ID && + phydev->phy_id != ATH8032_PHY_ID && + phydev->phy_id != QCA9561_PHY_ID) + phy_write(phydev, MII_CTRL1000, 0); + + /* we do all the (time consuming) work later */ + return 0; +} + +static int qca83xx_config_init(struct phy_device *phydev) +{ + u8 switch_revision; + + switch_revision = phydev->dev_flags & QCA8K_DEVFLAGS_REVISION_MASK; + + switch (switch_revision) { + case 1: + /* For 100M waveform */ + at803x_debug_reg_write(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, 0x02ea); + /* Turn on Gigabit clock */ + at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_GREEN, 0x68a0); + break; + + case 2: + phy_write_mmd(phydev, MDIO_MMD_AN, MDIO_AN_EEE_ADV, 0x0); + fallthrough; + case 4: + phy_write_mmd(phydev, MDIO_MMD_PCS, MDIO_AZ_DEBUG, 0x803f); + at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_GREEN, 0x6860); + at803x_debug_reg_write(phydev, AT803X_DEBUG_SYSTEM_CTRL_MODE, 0x2c46); + at803x_debug_reg_write(phydev, AT803X_DEBUG_REG_3C, 0x6000); + break; + } + + /* QCA8327 require DAC amplitude adjustment for 100m set to +6%. + * Disable on init and enable only with 100m speed following + * qca original source code. + */ + if (phydev->drv->phy_id == QCA8327_A_PHY_ID || + phydev->drv->phy_id == QCA8327_B_PHY_ID) + at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, + QCA8327_DEBUG_MANU_CTRL_EN, 0); + + /* Following original QCA sourcecode set port to prefer master */ + phy_set_bits(phydev, MII_CTRL1000, CTL1000_PREFER_MASTER); + + return 0; +} + +static void qca83xx_link_change_notify(struct phy_device *phydev) +{ + /* QCA8337 doesn't require DAC Amplitude adjustement */ + if (phydev->drv->phy_id == QCA8337_PHY_ID) + return; + + /* Set DAC Amplitude adjustment to +6% for 100m on link running */ + if (phydev->state == PHY_RUNNING) { + if (phydev->speed == SPEED_100) + at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, + QCA8327_DEBUG_MANU_CTRL_EN, + QCA8327_DEBUG_MANU_CTRL_EN); + } else { + /* Reset DAC Amplitude adjustment */ + at803x_debug_reg_mask(phydev, AT803X_DEBUG_ANALOG_TEST_CTRL, + QCA8327_DEBUG_MANU_CTRL_EN, 0); + } +} + +static int qca83xx_resume(struct phy_device *phydev) +{ + int ret, val; + + /* Skip reset if not suspended */ + if (!phydev->suspended) + return 0; + + /* Reinit the port, reset values set by suspend */ + qca83xx_config_init(phydev); + + /* Reset the port on port resume */ + phy_set_bits(phydev, MII_BMCR, BMCR_RESET | BMCR_ANENABLE); + + /* On resume from suspend the switch execute a reset and + * restart auto-negotiation. Wait for reset to complete. + */ + ret = phy_read_poll_timeout(phydev, MII_BMCR, val, !(val & BMCR_RESET), + 50000, 600000, true); + if (ret) + return ret; + + msleep(1); + + return 0; +} + +static int qca83xx_suspend(struct phy_device *phydev) +{ + u16 mask = 0; + + /* Only QCA8337 support actual suspend. + * QCA8327 cause port unreliability when phy suspend + * is set. + */ + if (phydev->drv->phy_id == QCA8337_PHY_ID) { + genphy_suspend(phydev); + } else { + mask |= ~(BMCR_SPEED1000 | BMCR_FULLDPLX); + phy_modify(phydev, MII_BMCR, mask, 0); + } + + at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_GREEN, + AT803X_DEBUG_GATE_CLK_IN1000, 0); + + at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_HIB_CTRL, + AT803X_DEBUG_HIB_CTRL_EN_ANY_CHANGE | + AT803X_DEBUG_HIB_CTRL_SEL_RST_80U, 0); + + return 0; +} + +static int qca808x_phy_fast_retrain_config(struct phy_device *phydev) +{ + int ret; + + /* Enable fast retrain */ + ret = genphy_c45_fast_retrain(phydev, true); + if (ret) + return ret; + + phy_write_mmd(phydev, MDIO_MMD_AN, QCA808X_PHY_MMD7_TOP_OPTION1, + QCA808X_TOP_OPTION1_DATA); + phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_20DB, + QCA808X_MSE_THRESHOLD_20DB_VALUE); + phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_17DB, + QCA808X_MSE_THRESHOLD_17DB_VALUE); + phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_27DB, + QCA808X_MSE_THRESHOLD_27DB_VALUE); + phy_write_mmd(phydev, MDIO_MMD_PMAPMD, QCA808X_PHY_MMD1_MSE_THRESHOLD_28DB, + QCA808X_MSE_THRESHOLD_28DB_VALUE); + phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_1, + QCA808X_MMD3_DEBUG_1_VALUE); + phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_4, + QCA808X_MMD3_DEBUG_4_VALUE); + phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_5, + QCA808X_MMD3_DEBUG_5_VALUE); + phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_3, + QCA808X_MMD3_DEBUG_3_VALUE); + phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_6, + QCA808X_MMD3_DEBUG_6_VALUE); + phy_write_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_DEBUG_2, + QCA808X_MMD3_DEBUG_2_VALUE); + + return 0; +} + +static int qca808x_phy_ms_random_seed_set(struct phy_device *phydev) +{ + u16 seed_value = prandom_u32_max(QCA808X_MASTER_SLAVE_SEED_RANGE); + + return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_LOCAL_SEED, + QCA808X_MASTER_SLAVE_SEED_CFG, + FIELD_PREP(QCA808X_MASTER_SLAVE_SEED_CFG, seed_value)); +} + +static int qca808x_phy_ms_seed_enable(struct phy_device *phydev, bool enable) +{ + u16 seed_enable = 0; + + if (enable) + seed_enable = QCA808X_MASTER_SLAVE_SEED_ENABLE; + + return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_LOCAL_SEED, + QCA808X_MASTER_SLAVE_SEED_ENABLE, seed_enable); +} + +static int qca808x_config_init(struct phy_device *phydev) +{ + int ret; + + /* Active adc&vga on 802.3az for the link 1000M and 100M */ + ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, QCA808X_PHY_MMD3_ADDR_CLD_CTRL7, + QCA808X_8023AZ_AFE_CTRL_MASK, QCA808X_8023AZ_AFE_EN); + if (ret) + return ret; + + /* Adjust the threshold on 802.3az for the link 1000M */ + ret = phy_write_mmd(phydev, MDIO_MMD_PCS, + QCA808X_PHY_MMD3_AZ_TRAINING_CTRL, QCA808X_MMD3_AZ_TRAINING_VAL); + if (ret) + return ret; + + /* Config the fast retrain for the link 2500M */ + ret = qca808x_phy_fast_retrain_config(phydev); + if (ret) + return ret; + + /* Configure lower ramdom seed to make phy linked as slave mode */ + ret = qca808x_phy_ms_random_seed_set(phydev); + if (ret) + return ret; + + /* Enable seed */ + ret = qca808x_phy_ms_seed_enable(phydev, true); + if (ret) + return ret; + + /* Configure adc threshold as 100mv for the link 10M */ + return at803x_debug_reg_mask(phydev, QCA808X_PHY_DEBUG_ADC_THRESHOLD, + QCA808X_ADC_THRESHOLD_MASK, QCA808X_ADC_THRESHOLD_100MV); +} + +static int qca808x_read_status(struct phy_device *phydev) +{ + int ret; + + ret = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_AN_10GBT_STAT); + if (ret < 0) + return ret; + + linkmode_mod_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, phydev->lp_advertising, + ret & MDIO_AN_10GBT_STAT_LP2_5G); + + ret = genphy_read_status(phydev); + if (ret) + return ret; + + ret = at803x_read_specific_status(phydev); + if (ret < 0) + return ret; + + if (phydev->link) { + if (phydev->speed == SPEED_2500) + phydev->interface = PHY_INTERFACE_MODE_2500BASEX; + else + phydev->interface = PHY_INTERFACE_MODE_SGMII; + } else { + /* generate seed as a lower random value to make PHY linked as SLAVE easily, + * except for master/slave configuration fault detected. + * the reason for not putting this code into the function link_change_notify is + * the corner case where the link partner is also the qca8081 PHY and the seed + * value is configured as the same value, the link can't be up and no link change + * occurs. + */ + if (phydev->master_slave_state == MASTER_SLAVE_STATE_ERR) { + qca808x_phy_ms_seed_enable(phydev, false); + } else { + qca808x_phy_ms_random_seed_set(phydev); + qca808x_phy_ms_seed_enable(phydev, true); + } + } + + return 0; +} + +static int qca808x_soft_reset(struct phy_device *phydev) +{ + int ret; + + ret = genphy_soft_reset(phydev); + if (ret < 0) + return ret; + + return qca808x_phy_ms_seed_enable(phydev, true); +} + +static bool qca808x_cdt_fault_length_valid(int cdt_code) +{ + switch (cdt_code) { + case QCA808X_CDT_STATUS_STAT_SHORT: + case QCA808X_CDT_STATUS_STAT_OPEN: + return true; + default: + return false; + } +} + +static int qca808x_cable_test_result_trans(int cdt_code) +{ + switch (cdt_code) { + case QCA808X_CDT_STATUS_STAT_NORMAL: + return ETHTOOL_A_CABLE_RESULT_CODE_OK; + case QCA808X_CDT_STATUS_STAT_SHORT: + return ETHTOOL_A_CABLE_RESULT_CODE_SAME_SHORT; + case QCA808X_CDT_STATUS_STAT_OPEN: + return ETHTOOL_A_CABLE_RESULT_CODE_OPEN; + case QCA808X_CDT_STATUS_STAT_FAIL: + default: + return ETHTOOL_A_CABLE_RESULT_CODE_UNSPEC; + } +} + +static int qca808x_cdt_fault_length(struct phy_device *phydev, int pair) +{ + int val; + u32 cdt_length_reg = 0; + + switch (pair) { + case ETHTOOL_A_CABLE_PAIR_A: + cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_A; + break; + case ETHTOOL_A_CABLE_PAIR_B: + cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_B; + break; + case ETHTOOL_A_CABLE_PAIR_C: + cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_C; + break; + case ETHTOOL_A_CABLE_PAIR_D: + cdt_length_reg = QCA808X_MMD3_CDT_DIAG_PAIR_D; + break; + default: + return -EINVAL; + } + + val = phy_read_mmd(phydev, MDIO_MMD_PCS, cdt_length_reg); + if (val < 0) + return val; + + return (FIELD_GET(QCA808X_CDT_DIAG_LENGTH, val) * 824) / 10; +} + +static int qca808x_cable_test_start(struct phy_device *phydev) +{ + int ret; + + /* perform CDT with the following configs: + * 1. disable hibernation. + * 2. force PHY working in MDI mode. + * 3. for PHY working in 1000BaseT. + * 4. configure the threshold. + */ + + ret = at803x_debug_reg_mask(phydev, QCA808X_DBG_AN_TEST, QCA808X_HIBERNATION_EN, 0); + if (ret < 0) + return ret; + + ret = at803x_config_mdix(phydev, ETH_TP_MDI); + if (ret < 0) + return ret; + + /* Force 1000base-T needs to configure PMA/PMD and MII_BMCR */ + phydev->duplex = DUPLEX_FULL; + phydev->speed = SPEED_1000; + ret = genphy_c45_pma_setup_forced(phydev); + if (ret < 0) + return ret; + + ret = genphy_setup_forced(phydev); + if (ret < 0) + return ret; + + /* configure the thresholds for open, short, pair ok test */ + phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8074, 0xc040); + phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8076, 0xc040); + phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8077, 0xa060); + phy_write_mmd(phydev, MDIO_MMD_PCS, 0x8078, 0xc050); + phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807a, 0xc060); + phy_write_mmd(phydev, MDIO_MMD_PCS, 0x807e, 0xb060); + + return 0; +} + +static int qca808x_cable_test_get_status(struct phy_device *phydev, bool *finished) +{ + int ret, val; + int pair_a, pair_b, pair_c, pair_d; + + *finished = false; + + ret = at803x_cdt_start(phydev, 0); + if (ret) + return ret; + + ret = at803x_cdt_wait_for_completion(phydev); + if (ret) + return ret; + + val = phy_read_mmd(phydev, MDIO_MMD_PCS, QCA808X_MMD3_CDT_STATUS); + if (val < 0) + return val; + + pair_a = FIELD_GET(QCA808X_CDT_CODE_PAIR_A, val); + pair_b = FIELD_GET(QCA808X_CDT_CODE_PAIR_B, val); + pair_c = FIELD_GET(QCA808X_CDT_CODE_PAIR_C, val); + pair_d = FIELD_GET(QCA808X_CDT_CODE_PAIR_D, val); + + ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_A, + qca808x_cable_test_result_trans(pair_a)); + ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_B, + qca808x_cable_test_result_trans(pair_b)); + ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_C, + qca808x_cable_test_result_trans(pair_c)); + ethnl_cable_test_result(phydev, ETHTOOL_A_CABLE_PAIR_D, + qca808x_cable_test_result_trans(pair_d)); + + if (qca808x_cdt_fault_length_valid(pair_a)) + ethnl_cable_test_fault_length(phydev, ETHTOOL_A_CABLE_PAIR_A, + qca808x_cdt_fault_length(phydev, ETHTOOL_A_CABLE_PAIR_A)); + if (qca808x_cdt_fault_length_valid(pair_b)) + ethnl_cable_test_fault_length(phydev, ETHTOOL_A_CABLE_PAIR_B, + qca808x_cdt_fault_length(phydev, ETHTOOL_A_CABLE_PAIR_B)); + if (qca808x_cdt_fault_length_valid(pair_c)) + ethnl_cable_test_fault_length(phydev, ETHTOOL_A_CABLE_PAIR_C, + qca808x_cdt_fault_length(phydev, ETHTOOL_A_CABLE_PAIR_C)); + if (qca808x_cdt_fault_length_valid(pair_d)) + ethnl_cable_test_fault_length(phydev, ETHTOOL_A_CABLE_PAIR_D, + qca808x_cdt_fault_length(phydev, ETHTOOL_A_CABLE_PAIR_D)); + + *finished = true; + + return 0; +} + +static struct phy_driver at803x_driver[] = { +{ + /* Qualcomm Atheros AR8035 */ + PHY_ID_MATCH_EXACT(ATH8035_PHY_ID), + .name = "Qualcomm Atheros AR8035", + .flags = PHY_POLL_CABLE_TEST, + .probe = at803x_probe, + .config_aneg = at803x_config_aneg, + .config_init = at803x_config_init, + .soft_reset = genphy_soft_reset, + .set_wol = at803x_set_wol, + .get_wol = at803x_get_wol, + .suspend = at803x_suspend, + .resume = at803x_resume, + /* PHY_GBIT_FEATURES */ + .read_status = at803x_read_status, + .config_intr = at803x_config_intr, + .handle_interrupt = at803x_handle_interrupt, + .get_tunable = at803x_get_tunable, + .set_tunable = at803x_set_tunable, + .cable_test_start = at803x_cable_test_start, + .cable_test_get_status = at803x_cable_test_get_status, +}, { + /* Qualcomm Atheros AR8030 */ + .phy_id = ATH8030_PHY_ID, + .name = "Qualcomm Atheros AR8030", + .phy_id_mask = AT8030_PHY_ID_MASK, + .probe = at803x_probe, + .config_init = at803x_config_init, + .link_change_notify = at803x_link_change_notify, + .set_wol = at803x_set_wol, + .get_wol = at803x_get_wol, + .suspend = at803x_suspend, + .resume = at803x_resume, + /* PHY_BASIC_FEATURES */ + .config_intr = at803x_config_intr, + .handle_interrupt = at803x_handle_interrupt, +}, { + /* Qualcomm Atheros AR8031/AR8033 */ + PHY_ID_MATCH_EXACT(ATH8031_PHY_ID), + .name = "Qualcomm Atheros AR8031/AR8033", + .flags = PHY_POLL_CABLE_TEST, + .probe = at803x_probe, + .config_init = at803x_config_init, + .config_aneg = at803x_config_aneg, + .soft_reset = genphy_soft_reset, + .set_wol = at803x_set_wol, + .get_wol = at803x_get_wol, + .suspend = at803x_suspend, + .resume = at803x_resume, + .read_page = at803x_read_page, + .write_page = at803x_write_page, + .get_features = at803x_get_features, + .read_status = at803x_read_status, + .config_intr = &at803x_config_intr, + .handle_interrupt = at803x_handle_interrupt, + .get_tunable = at803x_get_tunable, + .set_tunable = at803x_set_tunable, + .cable_test_start = at803x_cable_test_start, + .cable_test_get_status = at803x_cable_test_get_status, +}, { + /* Qualcomm Atheros AR8032 */ + PHY_ID_MATCH_EXACT(ATH8032_PHY_ID), + .name = "Qualcomm Atheros AR8032", + .probe = at803x_probe, + .flags = PHY_POLL_CABLE_TEST, + .config_init = at803x_config_init, + .link_change_notify = at803x_link_change_notify, + .suspend = at803x_suspend, + .resume = at803x_resume, + /* PHY_BASIC_FEATURES */ + .config_intr = at803x_config_intr, + .handle_interrupt = at803x_handle_interrupt, + .cable_test_start = at803x_cable_test_start, + .cable_test_get_status = at803x_cable_test_get_status, +}, { + /* ATHEROS AR9331 */ + PHY_ID_MATCH_EXACT(ATH9331_PHY_ID), + .name = "Qualcomm Atheros AR9331 built-in PHY", + .probe = at803x_probe, + .suspend = at803x_suspend, + .resume = at803x_resume, + .flags = PHY_POLL_CABLE_TEST, + /* PHY_BASIC_FEATURES */ + .config_intr = &at803x_config_intr, + .handle_interrupt = at803x_handle_interrupt, + .cable_test_start = at803x_cable_test_start, + .cable_test_get_status = at803x_cable_test_get_status, + .read_status = at803x_read_status, + .soft_reset = genphy_soft_reset, + .config_aneg = at803x_config_aneg, +}, { + /* Qualcomm Atheros QCA9561 */ + PHY_ID_MATCH_EXACT(QCA9561_PHY_ID), + .name = "Qualcomm Atheros QCA9561 built-in PHY", + .probe = at803x_probe, + .suspend = at803x_suspend, + .resume = at803x_resume, + .flags = PHY_POLL_CABLE_TEST, + /* PHY_BASIC_FEATURES */ + .config_intr = &at803x_config_intr, + .handle_interrupt = at803x_handle_interrupt, + .cable_test_start = at803x_cable_test_start, + .cable_test_get_status = at803x_cable_test_get_status, + .read_status = at803x_read_status, + .soft_reset = genphy_soft_reset, + .config_aneg = at803x_config_aneg, +}, { + /* QCA8337 */ + .phy_id = QCA8337_PHY_ID, + .phy_id_mask = QCA8K_PHY_ID_MASK, + .name = "Qualcomm Atheros 8337 internal PHY", + /* PHY_GBIT_FEATURES */ + .link_change_notify = qca83xx_link_change_notify, + .probe = at803x_probe, + .flags = PHY_IS_INTERNAL, + .config_init = qca83xx_config_init, + .soft_reset = genphy_soft_reset, + .get_sset_count = at803x_get_sset_count, + .get_strings = at803x_get_strings, + .get_stats = at803x_get_stats, + .suspend = qca83xx_suspend, + .resume = qca83xx_resume, +}, { + /* QCA8327-A from switch QCA8327-AL1A */ + .phy_id = QCA8327_A_PHY_ID, + .phy_id_mask = QCA8K_PHY_ID_MASK, + .name = "Qualcomm Atheros 8327-A internal PHY", + /* PHY_GBIT_FEATURES */ + .link_change_notify = qca83xx_link_change_notify, + .probe = at803x_probe, + .flags = PHY_IS_INTERNAL, + .config_init = qca83xx_config_init, + .soft_reset = genphy_soft_reset, + .get_sset_count = at803x_get_sset_count, + .get_strings = at803x_get_strings, + .get_stats = at803x_get_stats, + .suspend = qca83xx_suspend, + .resume = qca83xx_resume, +}, { + /* QCA8327-B from switch QCA8327-BL1A */ + .phy_id = QCA8327_B_PHY_ID, + .phy_id_mask = QCA8K_PHY_ID_MASK, + .name = "Qualcomm Atheros 8327-B internal PHY", + /* PHY_GBIT_FEATURES */ + .link_change_notify = qca83xx_link_change_notify, + .probe = at803x_probe, + .flags = PHY_IS_INTERNAL, + .config_init = qca83xx_config_init, + .soft_reset = genphy_soft_reset, + .get_sset_count = at803x_get_sset_count, + .get_strings = at803x_get_strings, + .get_stats = at803x_get_stats, + .suspend = qca83xx_suspend, + .resume = qca83xx_resume, +}, { + /* Qualcomm QCA8081 */ + PHY_ID_MATCH_EXACT(QCA8081_PHY_ID), + .name = "Qualcomm QCA8081", + .flags = PHY_POLL_CABLE_TEST, + .probe = at803x_probe, + .config_intr = at803x_config_intr, + .handle_interrupt = at803x_handle_interrupt, + .get_tunable = at803x_get_tunable, + .set_tunable = at803x_set_tunable, + .set_wol = at803x_set_wol, + .get_wol = at803x_get_wol, + .get_features = at803x_get_features, + .config_aneg = at803x_config_aneg, + .suspend = genphy_suspend, + .resume = genphy_resume, + .read_status = qca808x_read_status, + .config_init = qca808x_config_init, + .soft_reset = qca808x_soft_reset, + .cable_test_start = qca808x_cable_test_start, + .cable_test_get_status = qca808x_cable_test_get_status, +}, }; + +module_phy_driver(at803x_driver); + +static struct mdio_device_id __maybe_unused atheros_tbl[] = { + { ATH8030_PHY_ID, AT8030_PHY_ID_MASK }, + { PHY_ID_MATCH_EXACT(ATH8031_PHY_ID) }, + { PHY_ID_MATCH_EXACT(ATH8032_PHY_ID) }, + { PHY_ID_MATCH_EXACT(ATH8035_PHY_ID) }, + { PHY_ID_MATCH_EXACT(ATH9331_PHY_ID) }, + { PHY_ID_MATCH_EXACT(QCA8337_PHY_ID) }, + { PHY_ID_MATCH_EXACT(QCA8327_A_PHY_ID) }, + { PHY_ID_MATCH_EXACT(QCA8327_B_PHY_ID) }, + { PHY_ID_MATCH_EXACT(QCA9561_PHY_ID) }, + { PHY_ID_MATCH_EXACT(QCA8081_PHY_ID) }, + { } +}; + +MODULE_DEVICE_TABLE(mdio, atheros_tbl); |