diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c | 447 |
1 files changed, 447 insertions, 0 deletions
diff --git a/drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c b/drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c new file mode 100644 index 000000000..d2a1da8d9 --- /dev/null +++ b/drivers/phy/amlogic/phy-meson-g12a-usb3-pcie.c @@ -0,0 +1,447 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Amlogic G12A USB3 + PCIE Combo PHY driver + * + * Copyright (C) 2017 Amlogic, Inc. All rights reserved + * Copyright (C) 2019 BayLibre, SAS + * Author: Neil Armstrong <narmstrong@baylibre.com> + */ + +#include <linux/bitfield.h> +#include <linux/bitops.h> +#include <linux/clk.h> +#include <linux/module.h> +#include <linux/of_device.h> +#include <linux/phy/phy.h> +#include <linux/regmap.h> +#include <linux/reset.h> +#include <linux/platform_device.h> +#include <dt-bindings/phy/phy.h> + +#define PHY_R0 0x00 + #define PHY_R0_PCIE_POWER_STATE GENMASK(4, 0) + #define PHY_R0_PCIE_USB3_SWITCH GENMASK(6, 5) + +#define PHY_R1 0x04 + #define PHY_R1_PHY_TX1_TERM_OFFSET GENMASK(4, 0) + #define PHY_R1_PHY_TX0_TERM_OFFSET GENMASK(9, 5) + #define PHY_R1_PHY_RX1_EQ GENMASK(12, 10) + #define PHY_R1_PHY_RX0_EQ GENMASK(15, 13) + #define PHY_R1_PHY_LOS_LEVEL GENMASK(20, 16) + #define PHY_R1_PHY_LOS_BIAS GENMASK(23, 21) + #define PHY_R1_PHY_REF_CLKDIV2 BIT(24) + #define PHY_R1_PHY_MPLL_MULTIPLIER GENMASK(31, 25) + +#define PHY_R2 0x08 + #define PHY_R2_PCS_TX_DEEMPH_GEN2_6DB GENMASK(5, 0) + #define PHY_R2_PCS_TX_DEEMPH_GEN2_3P5DB GENMASK(11, 6) + #define PHY_R2_PCS_TX_DEEMPH_GEN1 GENMASK(17, 12) + #define PHY_R2_PHY_TX_VBOOST_LVL GENMASK(20, 18) + +#define PHY_R4 0x10 + #define PHY_R4_PHY_CR_WRITE BIT(0) + #define PHY_R4_PHY_CR_READ BIT(1) + #define PHY_R4_PHY_CR_DATA_IN GENMASK(17, 2) + #define PHY_R4_PHY_CR_CAP_DATA BIT(18) + #define PHY_R4_PHY_CR_CAP_ADDR BIT(19) + +#define PHY_R5 0x14 + #define PHY_R5_PHY_CR_DATA_OUT GENMASK(15, 0) + #define PHY_R5_PHY_CR_ACK BIT(16) + #define PHY_R5_PHY_BS_OUT BIT(17) + +#define PCIE_RESET_DELAY 500 + +struct phy_g12a_usb3_pcie_priv { + struct regmap *regmap; + struct regmap *regmap_cr; + struct clk *clk_ref; + struct reset_control *reset; + struct phy *phy; + unsigned int mode; +}; + +static const struct regmap_config phy_g12a_usb3_pcie_regmap_conf = { + .reg_bits = 8, + .val_bits = 32, + .reg_stride = 4, + .max_register = PHY_R5, +}; + +static int phy_g12a_usb3_pcie_cr_bus_addr(struct phy_g12a_usb3_pcie_priv *priv, + unsigned int addr) +{ + unsigned int val, reg; + int ret; + + reg = FIELD_PREP(PHY_R4_PHY_CR_DATA_IN, addr); + + regmap_write(priv->regmap, PHY_R4, reg); + regmap_write(priv->regmap, PHY_R4, reg); + + regmap_write(priv->regmap, PHY_R4, reg | PHY_R4_PHY_CR_CAP_ADDR); + + ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val, + (val & PHY_R5_PHY_CR_ACK), + 5, 1000); + if (ret) + return ret; + + regmap_write(priv->regmap, PHY_R4, reg); + + ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val, + !(val & PHY_R5_PHY_CR_ACK), + 5, 1000); + if (ret) + return ret; + + return 0; +} + +static int phy_g12a_usb3_pcie_cr_bus_read(void *context, unsigned int addr, + unsigned int *data) +{ + struct phy_g12a_usb3_pcie_priv *priv = context; + unsigned int val; + int ret; + + ret = phy_g12a_usb3_pcie_cr_bus_addr(priv, addr); + if (ret) + return ret; + + regmap_write(priv->regmap, PHY_R4, 0); + regmap_write(priv->regmap, PHY_R4, PHY_R4_PHY_CR_READ); + + ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val, + (val & PHY_R5_PHY_CR_ACK), + 5, 1000); + if (ret) + return ret; + + *data = FIELD_GET(PHY_R5_PHY_CR_DATA_OUT, val); + + regmap_write(priv->regmap, PHY_R4, 0); + + ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val, + !(val & PHY_R5_PHY_CR_ACK), + 5, 1000); + if (ret) + return ret; + + return 0; +} + +static int phy_g12a_usb3_pcie_cr_bus_write(void *context, unsigned int addr, + unsigned int data) +{ + struct phy_g12a_usb3_pcie_priv *priv = context; + unsigned int val, reg; + int ret; + + ret = phy_g12a_usb3_pcie_cr_bus_addr(priv, addr); + if (ret) + return ret; + + reg = FIELD_PREP(PHY_R4_PHY_CR_DATA_IN, data); + + regmap_write(priv->regmap, PHY_R4, reg); + regmap_write(priv->regmap, PHY_R4, reg); + + regmap_write(priv->regmap, PHY_R4, reg | PHY_R4_PHY_CR_CAP_DATA); + + ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val, + (val & PHY_R5_PHY_CR_ACK), + 5, 1000); + if (ret) + return ret; + + regmap_write(priv->regmap, PHY_R4, reg); + + ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val, + (val & PHY_R5_PHY_CR_ACK) == 0, + 5, 1000); + if (ret) + return ret; + + regmap_write(priv->regmap, PHY_R4, reg); + + regmap_write(priv->regmap, PHY_R4, reg | PHY_R4_PHY_CR_WRITE); + + ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val, + (val & PHY_R5_PHY_CR_ACK), + 5, 1000); + if (ret) + return ret; + + regmap_write(priv->regmap, PHY_R4, reg); + + ret = regmap_read_poll_timeout(priv->regmap, PHY_R5, val, + (val & PHY_R5_PHY_CR_ACK) == 0, + 5, 1000); + if (ret) + return ret; + + return 0; +} + +static const struct regmap_config phy_g12a_usb3_pcie_cr_regmap_conf = { + .reg_bits = 16, + .val_bits = 16, + .reg_read = phy_g12a_usb3_pcie_cr_bus_read, + .reg_write = phy_g12a_usb3_pcie_cr_bus_write, + .max_register = 0xffff, + .disable_locking = true, +}; + +static int phy_g12a_usb3_init(struct phy *phy) +{ + struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); + int data, ret; + + ret = reset_control_reset(priv->reset); + if (ret) + return ret; + + /* Switch PHY to USB3 */ + /* TODO figure out how to handle when PCIe was set in the bootloader */ + regmap_update_bits(priv->regmap, PHY_R0, + PHY_R0_PCIE_USB3_SWITCH, + PHY_R0_PCIE_USB3_SWITCH); + + /* + * WORKAROUND: There is SSPHY suspend bug due to + * which USB enumerates + * in HS mode instead of SS mode. Workaround it by asserting + * LANE0.TX_ALT_BLOCK.EN_ALT_BUS to enable TX to use alt bus + * mode + */ + ret = regmap_update_bits(priv->regmap_cr, 0x102d, BIT(7), BIT(7)); + if (ret) + return ret; + + ret = regmap_update_bits(priv->regmap_cr, 0x1010, 0xff0, 20); + if (ret) + return ret; + + /* + * Fix RX Equalization setting as follows + * LANE0.RX_OVRD_IN_HI. RX_EQ_EN set to 0 + * LANE0.RX_OVRD_IN_HI.RX_EQ_EN_OVRD set to 1 + * LANE0.RX_OVRD_IN_HI.RX_EQ set to 3 + * LANE0.RX_OVRD_IN_HI.RX_EQ_OVRD set to 1 + */ + ret = regmap_read(priv->regmap_cr, 0x1006, &data); + if (ret) + return ret; + + data &= ~BIT(6); + data |= BIT(7); + data &= ~(0x7 << 8); + data |= (0x3 << 8); + data |= (1 << 11); + ret = regmap_write(priv->regmap_cr, 0x1006, data); + if (ret) + return ret; + + /* + * Set EQ and TX launch amplitudes as follows + * LANE0.TX_OVRD_DRV_LO.PREEMPH set to 22 + * LANE0.TX_OVRD_DRV_LO.AMPLITUDE set to 127 + * LANE0.TX_OVRD_DRV_LO.EN set to 1. + */ + ret = regmap_read(priv->regmap_cr, 0x1002, &data); + if (ret) + return ret; + + data &= ~0x3f80; + data |= (0x16 << 7); + data &= ~0x7f; + data |= (0x7f | BIT(14)); + ret = regmap_write(priv->regmap_cr, 0x1002, data); + if (ret) + return ret; + + /* MPLL_LOOP_CTL.PROP_CNTRL = 8 */ + ret = regmap_update_bits(priv->regmap_cr, 0x30, 0xf << 4, 8 << 4); + if (ret) + return ret; + + regmap_update_bits(priv->regmap, PHY_R2, + PHY_R2_PHY_TX_VBOOST_LVL, + FIELD_PREP(PHY_R2_PHY_TX_VBOOST_LVL, 0x4)); + + regmap_update_bits(priv->regmap, PHY_R1, + PHY_R1_PHY_LOS_BIAS | PHY_R1_PHY_LOS_LEVEL, + FIELD_PREP(PHY_R1_PHY_LOS_BIAS, 4) | + FIELD_PREP(PHY_R1_PHY_LOS_LEVEL, 9)); + + return 0; +} + +static int phy_g12a_usb3_pcie_power_on(struct phy *phy) +{ + struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); + + if (priv->mode == PHY_TYPE_USB3) + return 0; + + regmap_update_bits(priv->regmap, PHY_R0, + PHY_R0_PCIE_POWER_STATE, + FIELD_PREP(PHY_R0_PCIE_POWER_STATE, 0x1c)); + + return 0; +} + +static int phy_g12a_usb3_pcie_power_off(struct phy *phy) +{ + struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); + + if (priv->mode == PHY_TYPE_USB3) + return 0; + + regmap_update_bits(priv->regmap, PHY_R0, + PHY_R0_PCIE_POWER_STATE, + FIELD_PREP(PHY_R0_PCIE_POWER_STATE, 0x1d)); + + return 0; +} + +static int phy_g12a_usb3_pcie_reset(struct phy *phy) +{ + struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); + int ret; + + if (priv->mode == PHY_TYPE_USB3) + return 0; + + ret = reset_control_assert(priv->reset); + if (ret) + return ret; + + udelay(PCIE_RESET_DELAY); + + ret = reset_control_deassert(priv->reset); + if (ret) + return ret; + + udelay(PCIE_RESET_DELAY); + + return 0; +} + +static int phy_g12a_usb3_pcie_init(struct phy *phy) +{ + struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); + + if (priv->mode == PHY_TYPE_USB3) + return phy_g12a_usb3_init(phy); + + return 0; +} + +static int phy_g12a_usb3_pcie_exit(struct phy *phy) +{ + struct phy_g12a_usb3_pcie_priv *priv = phy_get_drvdata(phy); + + if (priv->mode == PHY_TYPE_USB3) + return reset_control_reset(priv->reset); + + return 0; +} + +static struct phy *phy_g12a_usb3_pcie_xlate(struct device *dev, + struct of_phandle_args *args) +{ + struct phy_g12a_usb3_pcie_priv *priv = dev_get_drvdata(dev); + unsigned int mode; + + if (args->args_count < 1) { + dev_err(dev, "invalid number of arguments\n"); + return ERR_PTR(-EINVAL); + } + + mode = args->args[0]; + + if (mode != PHY_TYPE_USB3 && mode != PHY_TYPE_PCIE) { + dev_err(dev, "invalid phy mode select argument\n"); + return ERR_PTR(-EINVAL); + } + + priv->mode = mode; + + return priv->phy; +} + +static const struct phy_ops phy_g12a_usb3_pcie_ops = { + .init = phy_g12a_usb3_pcie_init, + .exit = phy_g12a_usb3_pcie_exit, + .power_on = phy_g12a_usb3_pcie_power_on, + .power_off = phy_g12a_usb3_pcie_power_off, + .reset = phy_g12a_usb3_pcie_reset, + .owner = THIS_MODULE, +}; + +static int phy_g12a_usb3_pcie_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct device_node *np = dev->of_node; + struct phy_g12a_usb3_pcie_priv *priv; + struct phy_provider *phy_provider; + void __iomem *base; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + base = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(base)) + return PTR_ERR(base); + + priv->regmap = devm_regmap_init_mmio(dev, base, + &phy_g12a_usb3_pcie_regmap_conf); + if (IS_ERR(priv->regmap)) + return PTR_ERR(priv->regmap); + + priv->regmap_cr = devm_regmap_init(dev, NULL, priv, + &phy_g12a_usb3_pcie_cr_regmap_conf); + if (IS_ERR(priv->regmap_cr)) + return PTR_ERR(priv->regmap_cr); + + priv->clk_ref = devm_clk_get_enabled(dev, "ref_clk"); + if (IS_ERR(priv->clk_ref)) + return PTR_ERR(priv->clk_ref); + + priv->reset = devm_reset_control_array_get_exclusive(dev); + if (IS_ERR(priv->reset)) + return PTR_ERR(priv->reset); + + priv->phy = devm_phy_create(dev, np, &phy_g12a_usb3_pcie_ops); + if (IS_ERR(priv->phy)) + return dev_err_probe(dev, PTR_ERR(priv->phy), "failed to create PHY\n"); + + phy_set_drvdata(priv->phy, priv); + dev_set_drvdata(dev, priv); + + phy_provider = devm_of_phy_provider_register(dev, + phy_g12a_usb3_pcie_xlate); + return PTR_ERR_OR_ZERO(phy_provider); +} + +static const struct of_device_id phy_g12a_usb3_pcie_of_match[] = { + { .compatible = "amlogic,g12a-usb3-pcie-phy", }, + { }, +}; +MODULE_DEVICE_TABLE(of, phy_g12a_usb3_pcie_of_match); + +static struct platform_driver phy_g12a_usb3_pcie_driver = { + .probe = phy_g12a_usb3_pcie_probe, + .driver = { + .name = "phy-g12a-usb3-pcie", + .of_match_table = phy_g12a_usb3_pcie_of_match, + }, +}; +module_platform_driver(phy_g12a_usb3_pcie_driver); + +MODULE_AUTHOR("Neil Armstrong <narmstrong@baylibre.com>"); +MODULE_DESCRIPTION("Amlogic G12A USB3 + PCIE Combo PHY driver"); +MODULE_LICENSE("GPL v2"); |