summaryrefslogtreecommitdiffstats
path: root/drivers/phy/st/phy-miphy28lp.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/phy/st/phy-miphy28lp.c')
-rw-r--r--drivers/phy/st/phy-miphy28lp.c1260
1 files changed, 1260 insertions, 0 deletions
diff --git a/drivers/phy/st/phy-miphy28lp.c b/drivers/phy/st/phy-miphy28lp.c
new file mode 100644
index 000000000..e30305b77
--- /dev/null
+++ b/drivers/phy/st/phy-miphy28lp.c
@@ -0,0 +1,1260 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014 STMicroelectronics
+ *
+ * STMicroelectronics PHY driver MiPHY28lp (for SoC STiH407).
+ *
+ * Author: Alexandre Torgue <alexandre.torgue@st.com>
+ */
+
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/clk.h>
+#include <linux/phy/phy.h>
+#include <linux/delay.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#include <dt-bindings/phy/phy.h>
+
+/* MiPHY registers */
+#define MIPHY_CONF_RESET 0x00
+#define RST_APPLI_SW BIT(0)
+#define RST_CONF_SW BIT(1)
+#define RST_MACRO_SW BIT(2)
+
+#define MIPHY_RESET 0x01
+#define RST_PLL_SW BIT(0)
+#define RST_COMP_SW BIT(2)
+
+#define MIPHY_STATUS_1 0x02
+#define PHY_RDY BIT(0)
+#define HFC_RDY BIT(1)
+#define HFC_PLL BIT(2)
+
+#define MIPHY_CONTROL 0x04
+#define TERM_EN_SW BIT(2)
+#define DIS_LINK_RST BIT(3)
+#define AUTO_RST_RX BIT(4)
+#define PX_RX_POL BIT(5)
+
+#define MIPHY_BOUNDARY_SEL 0x0a
+#define TX_SEL BIT(6)
+#define SSC_SEL BIT(4)
+#define GENSEL_SEL BIT(0)
+
+#define MIPHY_BOUNDARY_1 0x0b
+#define MIPHY_BOUNDARY_2 0x0c
+#define SSC_EN_SW BIT(2)
+
+#define MIPHY_PLL_CLKREF_FREQ 0x0d
+#define MIPHY_SPEED 0x0e
+#define TX_SPDSEL_80DEC 0
+#define TX_SPDSEL_40DEC 1
+#define TX_SPDSEL_20DEC 2
+#define RX_SPDSEL_80DEC 0
+#define RX_SPDSEL_40DEC (1 << 2)
+#define RX_SPDSEL_20DEC (2 << 2)
+
+#define MIPHY_CONF 0x0f
+#define MIPHY_CTRL_TEST_SEL 0x20
+#define MIPHY_CTRL_TEST_1 0x21
+#define MIPHY_CTRL_TEST_2 0x22
+#define MIPHY_CTRL_TEST_3 0x23
+#define MIPHY_CTRL_TEST_4 0x24
+#define MIPHY_FEEDBACK_TEST 0x25
+#define MIPHY_DEBUG_BUS 0x26
+#define MIPHY_DEBUG_STATUS_MSB 0x27
+#define MIPHY_DEBUG_STATUS_LSB 0x28
+#define MIPHY_PWR_RAIL_1 0x29
+#define MIPHY_PWR_RAIL_2 0x2a
+#define MIPHY_SYNCHAR_CONTROL 0x30
+
+#define MIPHY_COMP_FSM_1 0x3a
+#define COMP_START BIT(6)
+
+#define MIPHY_COMP_FSM_6 0x3f
+#define COMP_DONE BIT(7)
+
+#define MIPHY_COMP_POSTP 0x42
+#define MIPHY_TX_CTRL_1 0x49
+#define TX_REG_STEP_0V 0
+#define TX_REG_STEP_P_25MV 1
+#define TX_REG_STEP_P_50MV 2
+#define TX_REG_STEP_N_25MV 7
+#define TX_REG_STEP_N_50MV 6
+#define TX_REG_STEP_N_75MV 5
+
+#define MIPHY_TX_CTRL_2 0x4a
+#define TX_SLEW_SW_40_PS 0
+#define TX_SLEW_SW_80_PS 1
+#define TX_SLEW_SW_120_PS 2
+
+#define MIPHY_TX_CTRL_3 0x4b
+#define MIPHY_TX_CAL_MAN 0x4e
+#define TX_SLEW_CAL_MAN_EN BIT(0)
+
+#define MIPHY_TST_BIAS_BOOST_2 0x62
+#define MIPHY_BIAS_BOOST_1 0x63
+#define MIPHY_BIAS_BOOST_2 0x64
+#define MIPHY_RX_DESBUFF_FDB_2 0x67
+#define MIPHY_RX_DESBUFF_FDB_3 0x68
+#define MIPHY_SIGDET_COMPENS1 0x69
+#define MIPHY_SIGDET_COMPENS2 0x6a
+#define MIPHY_JITTER_PERIOD 0x6b
+#define MIPHY_JITTER_AMPLITUDE_1 0x6c
+#define MIPHY_JITTER_AMPLITUDE_2 0x6d
+#define MIPHY_JITTER_AMPLITUDE_3 0x6e
+#define MIPHY_RX_K_GAIN 0x78
+#define MIPHY_RX_BUFFER_CTRL 0x7a
+#define VGA_GAIN BIT(0)
+#define EQ_DC_GAIN BIT(2)
+#define EQ_BOOST_GAIN BIT(3)
+
+#define MIPHY_RX_VGA_GAIN 0x7b
+#define MIPHY_RX_EQU_GAIN_1 0x7f
+#define MIPHY_RX_EQU_GAIN_2 0x80
+#define MIPHY_RX_EQU_GAIN_3 0x81
+#define MIPHY_RX_CAL_CTRL_1 0x97
+#define MIPHY_RX_CAL_CTRL_2 0x98
+
+#define MIPHY_RX_CAL_OFFSET_CTRL 0x99
+#define CAL_OFFSET_VGA_64 (0x03 << 0)
+#define CAL_OFFSET_THRESHOLD_64 (0x03 << 2)
+#define VGA_OFFSET_POLARITY BIT(4)
+#define OFFSET_COMPENSATION_EN BIT(6)
+
+#define MIPHY_RX_CAL_VGA_STEP 0x9a
+#define MIPHY_RX_CAL_EYE_MIN 0x9d
+#define MIPHY_RX_CAL_OPT_LENGTH 0x9f
+#define MIPHY_RX_LOCK_CTRL_1 0xc1
+#define MIPHY_RX_LOCK_SETTINGS_OPT 0xc2
+#define MIPHY_RX_LOCK_STEP 0xc4
+
+#define MIPHY_RX_SIGDET_SLEEP_OA 0xc9
+#define MIPHY_RX_SIGDET_SLEEP_SEL 0xca
+#define MIPHY_RX_SIGDET_WAIT_SEL 0xcb
+#define MIPHY_RX_SIGDET_DATA_SEL 0xcc
+#define EN_ULTRA_LOW_POWER BIT(0)
+#define EN_FIRST_HALF BIT(1)
+#define EN_SECOND_HALF BIT(2)
+#define EN_DIGIT_SIGNAL_CHECK BIT(3)
+
+#define MIPHY_RX_POWER_CTRL_1 0xcd
+#define MIPHY_RX_POWER_CTRL_2 0xce
+#define MIPHY_PLL_CALSET_CTRL 0xd3
+#define MIPHY_PLL_CALSET_1 0xd4
+#define MIPHY_PLL_CALSET_2 0xd5
+#define MIPHY_PLL_CALSET_3 0xd6
+#define MIPHY_PLL_CALSET_4 0xd7
+#define MIPHY_PLL_SBR_1 0xe3
+#define SET_NEW_CHANGE BIT(1)
+
+#define MIPHY_PLL_SBR_2 0xe4
+#define MIPHY_PLL_SBR_3 0xe5
+#define MIPHY_PLL_SBR_4 0xe6
+#define MIPHY_PLL_COMMON_MISC_2 0xe9
+#define START_ACT_FILT BIT(6)
+
+#define MIPHY_PLL_SPAREIN 0xeb
+
+/*
+ * On STiH407 the glue logic can be different among MiPHY devices; for example:
+ * MiPHY0: OSC_FORCE_EXT means:
+ * 0: 30MHz crystal clk - 1: 100MHz ext clk routed through MiPHY1
+ * MiPHY1: OSC_FORCE_EXT means:
+ * 1: 30MHz crystal clk - 0: 100MHz ext clk routed through MiPHY1
+ * Some devices have not the possibility to check if the osc is ready.
+ */
+#define MIPHY_OSC_FORCE_EXT BIT(3)
+#define MIPHY_OSC_RDY BIT(5)
+
+#define MIPHY_CTRL_MASK 0x0f
+#define MIPHY_CTRL_DEFAULT 0
+#define MIPHY_CTRL_SYNC_D_EN BIT(2)
+
+/* SATA / PCIe defines */
+#define SATA_CTRL_MASK 0x07
+#define PCIE_CTRL_MASK 0xff
+#define SATA_CTRL_SELECT_SATA 1
+#define SATA_CTRL_SELECT_PCIE 0
+#define SYSCFG_PCIE_PCIE_VAL 0x80
+#define SATA_SPDMODE 1
+
+#define MIPHY_SATA_BANK_NB 3
+#define MIPHY_PCIE_BANK_NB 2
+
+enum {
+ SYSCFG_CTRL,
+ SYSCFG_STATUS,
+ SYSCFG_PCI,
+ SYSCFG_SATA,
+ SYSCFG_REG_MAX,
+};
+
+struct miphy28lp_phy {
+ struct phy *phy;
+ struct miphy28lp_dev *phydev;
+ void __iomem *base;
+ void __iomem *pipebase;
+
+ bool osc_force_ext;
+ bool osc_rdy;
+ bool px_rx_pol_inv;
+ bool ssc;
+ bool tx_impedance;
+
+ struct reset_control *miphy_rst;
+
+ u32 sata_gen;
+
+ /* Sysconfig registers offsets needed to configure the device */
+ u32 syscfg_reg[SYSCFG_REG_MAX];
+ u8 type;
+};
+
+struct miphy28lp_dev {
+ struct device *dev;
+ struct regmap *regmap;
+ struct mutex miphy_mutex;
+ struct miphy28lp_phy **phys;
+ int nphys;
+};
+
+struct miphy_initval {
+ u16 reg;
+ u16 val;
+};
+
+enum miphy_sata_gen { SATA_GEN1, SATA_GEN2, SATA_GEN3 };
+
+static char *PHY_TYPE_name[] = { "sata-up", "pcie-up", "", "usb3-up" };
+
+struct pll_ratio {
+ int clk_ref;
+ int calset_1;
+ int calset_2;
+ int calset_3;
+ int calset_4;
+ int cal_ctrl;
+};
+
+static struct pll_ratio sata_pll_ratio = {
+ .clk_ref = 0x1e,
+ .calset_1 = 0xc8,
+ .calset_2 = 0x00,
+ .calset_3 = 0x00,
+ .calset_4 = 0x00,
+ .cal_ctrl = 0x00,
+};
+
+static struct pll_ratio pcie_pll_ratio = {
+ .clk_ref = 0x1e,
+ .calset_1 = 0xa6,
+ .calset_2 = 0xaa,
+ .calset_3 = 0xaa,
+ .calset_4 = 0x00,
+ .cal_ctrl = 0x00,
+};
+
+static struct pll_ratio usb3_pll_ratio = {
+ .clk_ref = 0x1e,
+ .calset_1 = 0xa6,
+ .calset_2 = 0xaa,
+ .calset_3 = 0xaa,
+ .calset_4 = 0x04,
+ .cal_ctrl = 0x00,
+};
+
+struct miphy28lp_pll_gen {
+ int bank;
+ int speed;
+ int bias_boost_1;
+ int bias_boost_2;
+ int tx_ctrl_1;
+ int tx_ctrl_2;
+ int tx_ctrl_3;
+ int rx_k_gain;
+ int rx_vga_gain;
+ int rx_equ_gain_1;
+ int rx_equ_gain_2;
+ int rx_equ_gain_3;
+ int rx_buff_ctrl;
+};
+
+static struct miphy28lp_pll_gen sata_pll_gen[] = {
+ {
+ .bank = 0x00,
+ .speed = TX_SPDSEL_80DEC | RX_SPDSEL_80DEC,
+ .bias_boost_1 = 0x00,
+ .bias_boost_2 = 0xae,
+ .tx_ctrl_2 = 0x53,
+ .tx_ctrl_3 = 0x00,
+ .rx_buff_ctrl = EQ_BOOST_GAIN | EQ_DC_GAIN | VGA_GAIN,
+ .rx_vga_gain = 0x00,
+ .rx_equ_gain_1 = 0x7d,
+ .rx_equ_gain_2 = 0x56,
+ .rx_equ_gain_3 = 0x00,
+ },
+ {
+ .bank = 0x01,
+ .speed = TX_SPDSEL_40DEC | RX_SPDSEL_40DEC,
+ .bias_boost_1 = 0x00,
+ .bias_boost_2 = 0xae,
+ .tx_ctrl_2 = 0x72,
+ .tx_ctrl_3 = 0x20,
+ .rx_buff_ctrl = EQ_BOOST_GAIN | EQ_DC_GAIN | VGA_GAIN,
+ .rx_vga_gain = 0x00,
+ .rx_equ_gain_1 = 0x7d,
+ .rx_equ_gain_2 = 0x56,
+ .rx_equ_gain_3 = 0x00,
+ },
+ {
+ .bank = 0x02,
+ .speed = TX_SPDSEL_20DEC | RX_SPDSEL_20DEC,
+ .bias_boost_1 = 0x00,
+ .bias_boost_2 = 0xae,
+ .tx_ctrl_2 = 0xc0,
+ .tx_ctrl_3 = 0x20,
+ .rx_buff_ctrl = EQ_BOOST_GAIN | EQ_DC_GAIN | VGA_GAIN,
+ .rx_vga_gain = 0x00,
+ .rx_equ_gain_1 = 0x7d,
+ .rx_equ_gain_2 = 0x56,
+ .rx_equ_gain_3 = 0x00,
+ },
+};
+
+static struct miphy28lp_pll_gen pcie_pll_gen[] = {
+ {
+ .bank = 0x00,
+ .speed = TX_SPDSEL_40DEC | RX_SPDSEL_40DEC,
+ .bias_boost_1 = 0x00,
+ .bias_boost_2 = 0xa5,
+ .tx_ctrl_1 = TX_REG_STEP_N_25MV,
+ .tx_ctrl_2 = 0x71,
+ .tx_ctrl_3 = 0x60,
+ .rx_k_gain = 0x98,
+ .rx_buff_ctrl = EQ_BOOST_GAIN | EQ_DC_GAIN | VGA_GAIN,
+ .rx_vga_gain = 0x00,
+ .rx_equ_gain_1 = 0x79,
+ .rx_equ_gain_2 = 0x56,
+ },
+ {
+ .bank = 0x01,
+ .speed = TX_SPDSEL_20DEC | RX_SPDSEL_20DEC,
+ .bias_boost_1 = 0x00,
+ .bias_boost_2 = 0xa5,
+ .tx_ctrl_1 = TX_REG_STEP_N_25MV,
+ .tx_ctrl_2 = 0x70,
+ .tx_ctrl_3 = 0x60,
+ .rx_k_gain = 0xcc,
+ .rx_buff_ctrl = EQ_BOOST_GAIN | EQ_DC_GAIN | VGA_GAIN,
+ .rx_vga_gain = 0x00,
+ .rx_equ_gain_1 = 0x78,
+ .rx_equ_gain_2 = 0x07,
+ },
+};
+
+static inline void miphy28lp_set_reset(struct miphy28lp_phy *miphy_phy)
+{
+ void __iomem *base = miphy_phy->base;
+ u8 val;
+
+ /* Putting Macro in reset */
+ writeb_relaxed(RST_APPLI_SW, base + MIPHY_CONF_RESET);
+
+ val = RST_APPLI_SW | RST_CONF_SW;
+ writeb_relaxed(val, base + MIPHY_CONF_RESET);
+
+ writeb_relaxed(RST_APPLI_SW, base + MIPHY_CONF_RESET);
+
+ /* Bringing the MIPHY-CPU registers out of reset */
+ if (miphy_phy->type == PHY_TYPE_PCIE) {
+ val = AUTO_RST_RX | TERM_EN_SW;
+ writeb_relaxed(val, base + MIPHY_CONTROL);
+ } else {
+ val = AUTO_RST_RX | TERM_EN_SW | DIS_LINK_RST;
+ writeb_relaxed(val, base + MIPHY_CONTROL);
+ }
+}
+
+static inline void miphy28lp_pll_calibration(struct miphy28lp_phy *miphy_phy,
+ struct pll_ratio *pll_ratio)
+{
+ void __iomem *base = miphy_phy->base;
+ u8 val;
+
+ /* Applying PLL Settings */
+ writeb_relaxed(0x1d, base + MIPHY_PLL_SPAREIN);
+ writeb_relaxed(pll_ratio->clk_ref, base + MIPHY_PLL_CLKREF_FREQ);
+
+ /* PLL Ratio */
+ writeb_relaxed(pll_ratio->calset_1, base + MIPHY_PLL_CALSET_1);
+ writeb_relaxed(pll_ratio->calset_2, base + MIPHY_PLL_CALSET_2);
+ writeb_relaxed(pll_ratio->calset_3, base + MIPHY_PLL_CALSET_3);
+ writeb_relaxed(pll_ratio->calset_4, base + MIPHY_PLL_CALSET_4);
+ writeb_relaxed(pll_ratio->cal_ctrl, base + MIPHY_PLL_CALSET_CTRL);
+
+ writeb_relaxed(TX_SEL, base + MIPHY_BOUNDARY_SEL);
+
+ val = (0x68 << 1) | TX_SLEW_CAL_MAN_EN;
+ writeb_relaxed(val, base + MIPHY_TX_CAL_MAN);
+
+ val = VGA_OFFSET_POLARITY | CAL_OFFSET_THRESHOLD_64 | CAL_OFFSET_VGA_64;
+
+ if (miphy_phy->type != PHY_TYPE_SATA)
+ val |= OFFSET_COMPENSATION_EN;
+
+ writeb_relaxed(val, base + MIPHY_RX_CAL_OFFSET_CTRL);
+
+ if (miphy_phy->type == PHY_TYPE_USB3) {
+ writeb_relaxed(0x00, base + MIPHY_CONF);
+ writeb_relaxed(0x70, base + MIPHY_RX_LOCK_STEP);
+ writeb_relaxed(EN_FIRST_HALF, base + MIPHY_RX_SIGDET_SLEEP_OA);
+ writeb_relaxed(EN_FIRST_HALF, base + MIPHY_RX_SIGDET_SLEEP_SEL);
+ writeb_relaxed(EN_FIRST_HALF, base + MIPHY_RX_SIGDET_WAIT_SEL);
+
+ val = EN_DIGIT_SIGNAL_CHECK | EN_FIRST_HALF;
+ writeb_relaxed(val, base + MIPHY_RX_SIGDET_DATA_SEL);
+ }
+
+}
+
+static inline void miphy28lp_sata_config_gen(struct miphy28lp_phy *miphy_phy)
+{
+ void __iomem *base = miphy_phy->base;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(sata_pll_gen); i++) {
+ struct miphy28lp_pll_gen *gen = &sata_pll_gen[i];
+
+ /* Banked settings */
+ writeb_relaxed(gen->bank, base + MIPHY_CONF);
+ writeb_relaxed(gen->speed, base + MIPHY_SPEED);
+ writeb_relaxed(gen->bias_boost_1, base + MIPHY_BIAS_BOOST_1);
+ writeb_relaxed(gen->bias_boost_2, base + MIPHY_BIAS_BOOST_2);
+
+ /* TX buffer Settings */
+ writeb_relaxed(gen->tx_ctrl_2, base + MIPHY_TX_CTRL_2);
+ writeb_relaxed(gen->tx_ctrl_3, base + MIPHY_TX_CTRL_3);
+
+ /* RX Buffer Settings */
+ writeb_relaxed(gen->rx_buff_ctrl, base + MIPHY_RX_BUFFER_CTRL);
+ writeb_relaxed(gen->rx_vga_gain, base + MIPHY_RX_VGA_GAIN);
+ writeb_relaxed(gen->rx_equ_gain_1, base + MIPHY_RX_EQU_GAIN_1);
+ writeb_relaxed(gen->rx_equ_gain_2, base + MIPHY_RX_EQU_GAIN_2);
+ writeb_relaxed(gen->rx_equ_gain_3, base + MIPHY_RX_EQU_GAIN_3);
+ }
+}
+
+static inline void miphy28lp_pcie_config_gen(struct miphy28lp_phy *miphy_phy)
+{
+ void __iomem *base = miphy_phy->base;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(pcie_pll_gen); i++) {
+ struct miphy28lp_pll_gen *gen = &pcie_pll_gen[i];
+
+ /* Banked settings */
+ writeb_relaxed(gen->bank, base + MIPHY_CONF);
+ writeb_relaxed(gen->speed, base + MIPHY_SPEED);
+ writeb_relaxed(gen->bias_boost_1, base + MIPHY_BIAS_BOOST_1);
+ writeb_relaxed(gen->bias_boost_2, base + MIPHY_BIAS_BOOST_2);
+
+ /* TX buffer Settings */
+ writeb_relaxed(gen->tx_ctrl_1, base + MIPHY_TX_CTRL_1);
+ writeb_relaxed(gen->tx_ctrl_2, base + MIPHY_TX_CTRL_2);
+ writeb_relaxed(gen->tx_ctrl_3, base + MIPHY_TX_CTRL_3);
+
+ writeb_relaxed(gen->rx_k_gain, base + MIPHY_RX_K_GAIN);
+
+ /* RX Buffer Settings */
+ writeb_relaxed(gen->rx_buff_ctrl, base + MIPHY_RX_BUFFER_CTRL);
+ writeb_relaxed(gen->rx_vga_gain, base + MIPHY_RX_VGA_GAIN);
+ writeb_relaxed(gen->rx_equ_gain_1, base + MIPHY_RX_EQU_GAIN_1);
+ writeb_relaxed(gen->rx_equ_gain_2, base + MIPHY_RX_EQU_GAIN_2);
+ }
+}
+
+static inline int miphy28lp_wait_compensation(struct miphy28lp_phy *miphy_phy)
+{
+ u8 val;
+
+ /* Waiting for Compensation to complete */
+ return readb_relaxed_poll_timeout(miphy_phy->base + MIPHY_COMP_FSM_6,
+ val, val & COMP_DONE, 1, 5 * USEC_PER_SEC);
+}
+
+
+static inline int miphy28lp_compensation(struct miphy28lp_phy *miphy_phy,
+ struct pll_ratio *pll_ratio)
+{
+ void __iomem *base = miphy_phy->base;
+
+ /* Poll for HFC ready after reset release */
+ /* Compensation measurement */
+ writeb_relaxed(RST_PLL_SW | RST_COMP_SW, base + MIPHY_RESET);
+
+ writeb_relaxed(0x00, base + MIPHY_PLL_COMMON_MISC_2);
+ writeb_relaxed(pll_ratio->clk_ref, base + MIPHY_PLL_CLKREF_FREQ);
+ writeb_relaxed(COMP_START, base + MIPHY_COMP_FSM_1);
+
+ if (miphy_phy->type == PHY_TYPE_PCIE)
+ writeb_relaxed(RST_PLL_SW, base + MIPHY_RESET);
+
+ writeb_relaxed(0x00, base + MIPHY_RESET);
+ writeb_relaxed(START_ACT_FILT, base + MIPHY_PLL_COMMON_MISC_2);
+ writeb_relaxed(SET_NEW_CHANGE, base + MIPHY_PLL_SBR_1);
+
+ /* TX compensation offset to re-center TX impedance */
+ writeb_relaxed(0x00, base + MIPHY_COMP_POSTP);
+
+ if (miphy_phy->type == PHY_TYPE_PCIE)
+ return miphy28lp_wait_compensation(miphy_phy);
+
+ return 0;
+}
+
+static inline void miphy28_usb3_miphy_reset(struct miphy28lp_phy *miphy_phy)
+{
+ void __iomem *base = miphy_phy->base;
+ u8 val;
+
+ /* MIPHY Reset */
+ writeb_relaxed(RST_APPLI_SW, base + MIPHY_CONF_RESET);
+ writeb_relaxed(0x00, base + MIPHY_CONF_RESET);
+ writeb_relaxed(RST_COMP_SW, base + MIPHY_RESET);
+
+ val = RST_COMP_SW | RST_PLL_SW;
+ writeb_relaxed(val, base + MIPHY_RESET);
+
+ writeb_relaxed(0x00, base + MIPHY_PLL_COMMON_MISC_2);
+ writeb_relaxed(0x1e, base + MIPHY_PLL_CLKREF_FREQ);
+ writeb_relaxed(COMP_START, base + MIPHY_COMP_FSM_1);
+ writeb_relaxed(RST_PLL_SW, base + MIPHY_RESET);
+ writeb_relaxed(0x00, base + MIPHY_RESET);
+ writeb_relaxed(START_ACT_FILT, base + MIPHY_PLL_COMMON_MISC_2);
+ writeb_relaxed(0x00, base + MIPHY_CONF);
+ writeb_relaxed(0x00, base + MIPHY_BOUNDARY_1);
+ writeb_relaxed(0x00, base + MIPHY_TST_BIAS_BOOST_2);
+ writeb_relaxed(0x00, base + MIPHY_CONF);
+ writeb_relaxed(SET_NEW_CHANGE, base + MIPHY_PLL_SBR_1);
+ writeb_relaxed(0xa5, base + MIPHY_DEBUG_BUS);
+ writeb_relaxed(0x00, base + MIPHY_CONF);
+}
+
+static void miphy_sata_tune_ssc(struct miphy28lp_phy *miphy_phy)
+{
+ void __iomem *base = miphy_phy->base;
+ u8 val;
+
+ /* Compensate Tx impedance to avoid out of range values */
+ /*
+ * Enable the SSC on PLL for all banks
+ * SSC Modulation @ 31 KHz and 4000 ppm modulation amp
+ */
+ val = readb_relaxed(base + MIPHY_BOUNDARY_2);
+ val |= SSC_EN_SW;
+ writeb_relaxed(val, base + MIPHY_BOUNDARY_2);
+
+ val = readb_relaxed(base + MIPHY_BOUNDARY_SEL);
+ val |= SSC_SEL;
+ writeb_relaxed(val, base + MIPHY_BOUNDARY_SEL);
+
+ for (val = 0; val < MIPHY_SATA_BANK_NB; val++) {
+ writeb_relaxed(val, base + MIPHY_CONF);
+
+ /* Add value to each reference clock cycle */
+ /* and define the period length of the SSC */
+ writeb_relaxed(0x3c, base + MIPHY_PLL_SBR_2);
+ writeb_relaxed(0x6c, base + MIPHY_PLL_SBR_3);
+ writeb_relaxed(0x81, base + MIPHY_PLL_SBR_4);
+
+ /* Clear any previous request */
+ writeb_relaxed(0x00, base + MIPHY_PLL_SBR_1);
+
+ /* requests the PLL to take in account new parameters */
+ writeb_relaxed(SET_NEW_CHANGE, base + MIPHY_PLL_SBR_1);
+
+ /* To be sure there is no other pending requests */
+ writeb_relaxed(0x00, base + MIPHY_PLL_SBR_1);
+ }
+}
+
+static void miphy_pcie_tune_ssc(struct miphy28lp_phy *miphy_phy)
+{
+ void __iomem *base = miphy_phy->base;
+ u8 val;
+
+ /* Compensate Tx impedance to avoid out of range values */
+ /*
+ * Enable the SSC on PLL for all banks
+ * SSC Modulation @ 31 KHz and 4000 ppm modulation amp
+ */
+ val = readb_relaxed(base + MIPHY_BOUNDARY_2);
+ val |= SSC_EN_SW;
+ writeb_relaxed(val, base + MIPHY_BOUNDARY_2);
+
+ val = readb_relaxed(base + MIPHY_BOUNDARY_SEL);
+ val |= SSC_SEL;
+ writeb_relaxed(val, base + MIPHY_BOUNDARY_SEL);
+
+ for (val = 0; val < MIPHY_PCIE_BANK_NB; val++) {
+ writeb_relaxed(val, base + MIPHY_CONF);
+
+ /* Validate Step component */
+ writeb_relaxed(0x69, base + MIPHY_PLL_SBR_3);
+ writeb_relaxed(0x21, base + MIPHY_PLL_SBR_4);
+
+ /* Validate Period component */
+ writeb_relaxed(0x3c, base + MIPHY_PLL_SBR_2);
+ writeb_relaxed(0x21, base + MIPHY_PLL_SBR_4);
+
+ /* Clear any previous request */
+ writeb_relaxed(0x00, base + MIPHY_PLL_SBR_1);
+
+ /* requests the PLL to take in account new parameters */
+ writeb_relaxed(SET_NEW_CHANGE, base + MIPHY_PLL_SBR_1);
+
+ /* To be sure there is no other pending requests */
+ writeb_relaxed(0x00, base + MIPHY_PLL_SBR_1);
+ }
+}
+
+static inline void miphy_tune_tx_impedance(struct miphy28lp_phy *miphy_phy)
+{
+ /* Compensate Tx impedance to avoid out of range values */
+ writeb_relaxed(0x02, miphy_phy->base + MIPHY_COMP_POSTP);
+}
+
+static inline int miphy28lp_configure_sata(struct miphy28lp_phy *miphy_phy)
+{
+ void __iomem *base = miphy_phy->base;
+ int err;
+ u8 val;
+
+ /* Putting Macro in reset */
+ miphy28lp_set_reset(miphy_phy);
+
+ /* PLL calibration */
+ miphy28lp_pll_calibration(miphy_phy, &sata_pll_ratio);
+
+ /* Banked settings Gen1/Gen2/Gen3 */
+ miphy28lp_sata_config_gen(miphy_phy);
+
+ /* Power control */
+ /* Input bridge enable, manual input bridge control */
+ writeb_relaxed(0x21, base + MIPHY_RX_POWER_CTRL_1);
+
+ /* Macro out of reset */
+ writeb_relaxed(0x00, base + MIPHY_CONF_RESET);
+
+ /* Poll for HFC ready after reset release */
+ /* Compensation measurement */
+ err = miphy28lp_compensation(miphy_phy, &sata_pll_ratio);
+ if (err)
+ return err;
+
+ if (miphy_phy->px_rx_pol_inv) {
+ /* Invert Rx polarity */
+ val = readb_relaxed(miphy_phy->base + MIPHY_CONTROL);
+ val |= PX_RX_POL;
+ writeb_relaxed(val, miphy_phy->base + MIPHY_CONTROL);
+ }
+
+ if (miphy_phy->ssc)
+ miphy_sata_tune_ssc(miphy_phy);
+
+ if (miphy_phy->tx_impedance)
+ miphy_tune_tx_impedance(miphy_phy);
+
+ return 0;
+}
+
+static inline int miphy28lp_configure_pcie(struct miphy28lp_phy *miphy_phy)
+{
+ void __iomem *base = miphy_phy->base;
+ int err;
+
+ /* Putting Macro in reset */
+ miphy28lp_set_reset(miphy_phy);
+
+ /* PLL calibration */
+ miphy28lp_pll_calibration(miphy_phy, &pcie_pll_ratio);
+
+ /* Banked settings Gen1/Gen2 */
+ miphy28lp_pcie_config_gen(miphy_phy);
+
+ /* Power control */
+ /* Input bridge enable, manual input bridge control */
+ writeb_relaxed(0x21, base + MIPHY_RX_POWER_CTRL_1);
+
+ /* Macro out of reset */
+ writeb_relaxed(0x00, base + MIPHY_CONF_RESET);
+
+ /* Poll for HFC ready after reset release */
+ /* Compensation measurement */
+ err = miphy28lp_compensation(miphy_phy, &pcie_pll_ratio);
+ if (err)
+ return err;
+
+ if (miphy_phy->ssc)
+ miphy_pcie_tune_ssc(miphy_phy);
+
+ if (miphy_phy->tx_impedance)
+ miphy_tune_tx_impedance(miphy_phy);
+
+ return 0;
+}
+
+
+static inline void miphy28lp_configure_usb3(struct miphy28lp_phy *miphy_phy)
+{
+ void __iomem *base = miphy_phy->base;
+ u8 val;
+
+ /* Putting Macro in reset */
+ miphy28lp_set_reset(miphy_phy);
+
+ /* PLL calibration */
+ miphy28lp_pll_calibration(miphy_phy, &usb3_pll_ratio);
+
+ /* Writing The Speed Rate */
+ writeb_relaxed(0x00, base + MIPHY_CONF);
+
+ val = RX_SPDSEL_20DEC | TX_SPDSEL_20DEC;
+ writeb_relaxed(val, base + MIPHY_SPEED);
+
+ /* RX Channel compensation and calibration */
+ writeb_relaxed(0x1c, base + MIPHY_RX_LOCK_SETTINGS_OPT);
+ writeb_relaxed(0x51, base + MIPHY_RX_CAL_CTRL_1);
+ writeb_relaxed(0x70, base + MIPHY_RX_CAL_CTRL_2);
+
+ val = OFFSET_COMPENSATION_EN | VGA_OFFSET_POLARITY |
+ CAL_OFFSET_THRESHOLD_64 | CAL_OFFSET_VGA_64;
+ writeb_relaxed(val, base + MIPHY_RX_CAL_OFFSET_CTRL);
+ writeb_relaxed(0x22, base + MIPHY_RX_CAL_VGA_STEP);
+ writeb_relaxed(0x0e, base + MIPHY_RX_CAL_OPT_LENGTH);
+
+ val = EQ_DC_GAIN | VGA_GAIN;
+ writeb_relaxed(val, base + MIPHY_RX_BUFFER_CTRL);
+ writeb_relaxed(0x78, base + MIPHY_RX_EQU_GAIN_1);
+ writeb_relaxed(0x1b, base + MIPHY_SYNCHAR_CONTROL);
+
+ /* TX compensation offset to re-center TX impedance */
+ writeb_relaxed(0x02, base + MIPHY_COMP_POSTP);
+
+ /* Enable GENSEL_SEL and SSC */
+ /* TX_SEL=0 swing preemp forced by pipe registres */
+ val = SSC_SEL | GENSEL_SEL;
+ writeb_relaxed(val, base + MIPHY_BOUNDARY_SEL);
+
+ /* MIPHY Bias boost */
+ writeb_relaxed(0x00, base + MIPHY_BIAS_BOOST_1);
+ writeb_relaxed(0xa7, base + MIPHY_BIAS_BOOST_2);
+
+ /* SSC modulation */
+ writeb_relaxed(SSC_EN_SW, base + MIPHY_BOUNDARY_2);
+
+ /* MIPHY TX control */
+ writeb_relaxed(0x00, base + MIPHY_CONF);
+
+ /* Validate Step component */
+ writeb_relaxed(0x5a, base + MIPHY_PLL_SBR_3);
+ writeb_relaxed(0xa0, base + MIPHY_PLL_SBR_4);
+
+ /* Validate Period component */
+ writeb_relaxed(0x3c, base + MIPHY_PLL_SBR_2);
+ writeb_relaxed(0xa1, base + MIPHY_PLL_SBR_4);
+
+ /* Clear any previous request */
+ writeb_relaxed(0x00, base + MIPHY_PLL_SBR_1);
+
+ /* requests the PLL to take in account new parameters */
+ writeb_relaxed(0x02, base + MIPHY_PLL_SBR_1);
+
+ /* To be sure there is no other pending requests */
+ writeb_relaxed(0x00, base + MIPHY_PLL_SBR_1);
+
+ /* Rx PI controller settings */
+ writeb_relaxed(0xca, base + MIPHY_RX_K_GAIN);
+
+ /* MIPHY RX input bridge control */
+ /* INPUT_BRIDGE_EN_SW=1, manual input bridge control[0]=1 */
+ writeb_relaxed(0x21, base + MIPHY_RX_POWER_CTRL_1);
+ writeb_relaxed(0x29, base + MIPHY_RX_POWER_CTRL_1);
+ writeb_relaxed(0x1a, base + MIPHY_RX_POWER_CTRL_2);
+
+ /* MIPHY Reset for usb3 */
+ miphy28_usb3_miphy_reset(miphy_phy);
+}
+
+static inline int miphy_is_ready(struct miphy28lp_phy *miphy_phy)
+{
+ u8 mask = HFC_PLL | HFC_RDY;
+ u8 val;
+
+ /*
+ * For PCIe and USB3 check only that PLL and HFC are ready
+ * For SATA check also that phy is ready!
+ */
+ if (miphy_phy->type == PHY_TYPE_SATA)
+ mask |= PHY_RDY;
+
+ return readb_relaxed_poll_timeout(miphy_phy->base + MIPHY_STATUS_1,
+ val, (val & mask) == mask, 1,
+ 5 * USEC_PER_SEC);
+}
+
+static int miphy_osc_is_ready(struct miphy28lp_phy *miphy_phy)
+{
+ struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
+ u32 val;
+
+ if (!miphy_phy->osc_rdy)
+ return 0;
+
+ if (!miphy_phy->syscfg_reg[SYSCFG_STATUS])
+ return -EINVAL;
+
+ return regmap_read_poll_timeout(miphy_dev->regmap,
+ miphy_phy->syscfg_reg[SYSCFG_STATUS],
+ val, val & MIPHY_OSC_RDY, 1,
+ 5 * USEC_PER_SEC);
+}
+
+static int miphy28lp_get_resource_byname(struct device_node *child,
+ char *rname, struct resource *res)
+{
+ int index;
+
+ index = of_property_match_string(child, "reg-names", rname);
+ if (index < 0)
+ return -ENODEV;
+
+ return of_address_to_resource(child, index, res);
+}
+
+static int miphy28lp_get_one_addr(struct device *dev,
+ struct device_node *child, char *rname,
+ void __iomem **base)
+{
+ struct resource res;
+ int ret;
+
+ ret = miphy28lp_get_resource_byname(child, rname, &res);
+ if (!ret) {
+ *base = devm_ioremap(dev, res.start, resource_size(&res));
+ if (!*base) {
+ dev_err(dev, "failed to ioremap %s address region\n"
+ , rname);
+ return -ENOENT;
+ }
+ }
+
+ return 0;
+}
+
+/* MiPHY reset and sysconf setup */
+static int miphy28lp_setup(struct miphy28lp_phy *miphy_phy, u32 miphy_val)
+{
+ int err;
+ struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
+
+ if (!miphy_phy->syscfg_reg[SYSCFG_CTRL])
+ return -EINVAL;
+
+ err = reset_control_assert(miphy_phy->miphy_rst);
+ if (err) {
+ dev_err(miphy_dev->dev, "unable to bring out of miphy reset\n");
+ return err;
+ }
+
+ if (miphy_phy->osc_force_ext)
+ miphy_val |= MIPHY_OSC_FORCE_EXT;
+
+ regmap_update_bits(miphy_dev->regmap,
+ miphy_phy->syscfg_reg[SYSCFG_CTRL],
+ MIPHY_CTRL_MASK, miphy_val);
+
+ err = reset_control_deassert(miphy_phy->miphy_rst);
+ if (err) {
+ dev_err(miphy_dev->dev, "unable to bring out of miphy reset\n");
+ return err;
+ }
+
+ return miphy_osc_is_ready(miphy_phy);
+}
+
+static int miphy28lp_init_sata(struct miphy28lp_phy *miphy_phy)
+{
+ struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
+ int err, sata_conf = SATA_CTRL_SELECT_SATA;
+
+ if ((!miphy_phy->syscfg_reg[SYSCFG_SATA]) ||
+ (!miphy_phy->syscfg_reg[SYSCFG_PCI]) ||
+ (!miphy_phy->base))
+ return -EINVAL;
+
+ dev_info(miphy_dev->dev, "sata-up mode, addr 0x%p\n", miphy_phy->base);
+
+ /* Configure the glue-logic */
+ sata_conf |= ((miphy_phy->sata_gen - SATA_GEN1) << SATA_SPDMODE);
+
+ regmap_update_bits(miphy_dev->regmap,
+ miphy_phy->syscfg_reg[SYSCFG_SATA],
+ SATA_CTRL_MASK, sata_conf);
+
+ regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_reg[SYSCFG_PCI],
+ PCIE_CTRL_MASK, SATA_CTRL_SELECT_PCIE);
+
+ /* MiPHY path and clocking init */
+ err = miphy28lp_setup(miphy_phy, MIPHY_CTRL_DEFAULT);
+
+ if (err) {
+ dev_err(miphy_dev->dev, "SATA phy setup failed\n");
+ return err;
+ }
+
+ /* initialize miphy */
+ miphy28lp_configure_sata(miphy_phy);
+
+ return miphy_is_ready(miphy_phy);
+}
+
+static int miphy28lp_init_pcie(struct miphy28lp_phy *miphy_phy)
+{
+ struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
+ int err;
+
+ if ((!miphy_phy->syscfg_reg[SYSCFG_SATA]) ||
+ (!miphy_phy->syscfg_reg[SYSCFG_PCI])
+ || (!miphy_phy->base) || (!miphy_phy->pipebase))
+ return -EINVAL;
+
+ dev_info(miphy_dev->dev, "pcie-up mode, addr 0x%p\n", miphy_phy->base);
+
+ /* Configure the glue-logic */
+ regmap_update_bits(miphy_dev->regmap,
+ miphy_phy->syscfg_reg[SYSCFG_SATA],
+ SATA_CTRL_MASK, SATA_CTRL_SELECT_PCIE);
+
+ regmap_update_bits(miphy_dev->regmap, miphy_phy->syscfg_reg[SYSCFG_PCI],
+ PCIE_CTRL_MASK, SYSCFG_PCIE_PCIE_VAL);
+
+ /* MiPHY path and clocking init */
+ err = miphy28lp_setup(miphy_phy, MIPHY_CTRL_DEFAULT);
+
+ if (err) {
+ dev_err(miphy_dev->dev, "PCIe phy setup failed\n");
+ return err;
+ }
+
+ /* initialize miphy */
+ err = miphy28lp_configure_pcie(miphy_phy);
+ if (err)
+ return err;
+
+ /* PIPE Wrapper Configuration */
+ writeb_relaxed(0x68, miphy_phy->pipebase + 0x104); /* Rise_0 */
+ writeb_relaxed(0x61, miphy_phy->pipebase + 0x105); /* Rise_1 */
+ writeb_relaxed(0x68, miphy_phy->pipebase + 0x108); /* Fall_0 */
+ writeb_relaxed(0x61, miphy_phy->pipebase + 0x109); /* Fall-1 */
+ writeb_relaxed(0x68, miphy_phy->pipebase + 0x10c); /* Threshold_0 */
+ writeb_relaxed(0x60, miphy_phy->pipebase + 0x10d); /* Threshold_1 */
+
+ /* Wait for phy_ready */
+ return miphy_is_ready(miphy_phy);
+}
+
+static int miphy28lp_init_usb3(struct miphy28lp_phy *miphy_phy)
+{
+ struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
+ int err;
+
+ if ((!miphy_phy->base) || (!miphy_phy->pipebase))
+ return -EINVAL;
+
+ dev_info(miphy_dev->dev, "usb3-up mode, addr 0x%p\n", miphy_phy->base);
+
+ /* MiPHY path and clocking init */
+ err = miphy28lp_setup(miphy_phy, MIPHY_CTRL_SYNC_D_EN);
+ if (err) {
+ dev_err(miphy_dev->dev, "USB3 phy setup failed\n");
+ return err;
+ }
+
+ /* initialize miphy */
+ miphy28lp_configure_usb3(miphy_phy);
+
+ /* PIPE Wrapper Configuration */
+ writeb_relaxed(0x68, miphy_phy->pipebase + 0x23);
+ writeb_relaxed(0x61, miphy_phy->pipebase + 0x24);
+ writeb_relaxed(0x68, miphy_phy->pipebase + 0x26);
+ writeb_relaxed(0x61, miphy_phy->pipebase + 0x27);
+ writeb_relaxed(0x18, miphy_phy->pipebase + 0x29);
+ writeb_relaxed(0x61, miphy_phy->pipebase + 0x2a);
+
+ /* pipe Wrapper usb3 TX swing de-emph margin PREEMPH[7:4], SWING[3:0] */
+ writeb_relaxed(0X67, miphy_phy->pipebase + 0x68);
+ writeb_relaxed(0x0d, miphy_phy->pipebase + 0x69);
+ writeb_relaxed(0X67, miphy_phy->pipebase + 0x6a);
+ writeb_relaxed(0X0d, miphy_phy->pipebase + 0x6b);
+ writeb_relaxed(0X67, miphy_phy->pipebase + 0x6c);
+ writeb_relaxed(0X0d, miphy_phy->pipebase + 0x6d);
+ writeb_relaxed(0X67, miphy_phy->pipebase + 0x6e);
+ writeb_relaxed(0X0d, miphy_phy->pipebase + 0x6f);
+
+ return miphy_is_ready(miphy_phy);
+}
+
+static int miphy28lp_init(struct phy *phy)
+{
+ struct miphy28lp_phy *miphy_phy = phy_get_drvdata(phy);
+ struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
+ int ret;
+
+ mutex_lock(&miphy_dev->miphy_mutex);
+
+ switch (miphy_phy->type) {
+
+ case PHY_TYPE_SATA:
+ ret = miphy28lp_init_sata(miphy_phy);
+ break;
+ case PHY_TYPE_PCIE:
+ ret = miphy28lp_init_pcie(miphy_phy);
+ break;
+ case PHY_TYPE_USB3:
+ ret = miphy28lp_init_usb3(miphy_phy);
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ mutex_unlock(&miphy_dev->miphy_mutex);
+
+ return ret;
+}
+
+static int miphy28lp_get_addr(struct miphy28lp_phy *miphy_phy)
+{
+ struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
+ struct device_node *phynode = miphy_phy->phy->dev.of_node;
+ int err;
+
+ if ((miphy_phy->type != PHY_TYPE_SATA) &&
+ (miphy_phy->type != PHY_TYPE_PCIE) &&
+ (miphy_phy->type != PHY_TYPE_USB3)) {
+ return -EINVAL;
+ }
+
+ err = miphy28lp_get_one_addr(miphy_dev->dev, phynode,
+ PHY_TYPE_name[miphy_phy->type - PHY_TYPE_SATA],
+ &miphy_phy->base);
+ if (err)
+ return err;
+
+ if ((miphy_phy->type == PHY_TYPE_PCIE) ||
+ (miphy_phy->type == PHY_TYPE_USB3)) {
+ err = miphy28lp_get_one_addr(miphy_dev->dev, phynode, "pipew",
+ &miphy_phy->pipebase);
+ if (err)
+ return err;
+ }
+
+ return 0;
+}
+
+static struct phy *miphy28lp_xlate(struct device *dev,
+ struct of_phandle_args *args)
+{
+ struct miphy28lp_dev *miphy_dev = dev_get_drvdata(dev);
+ struct miphy28lp_phy *miphy_phy = NULL;
+ struct device_node *phynode = args->np;
+ int ret, index = 0;
+
+ if (args->args_count != 1) {
+ dev_err(dev, "Invalid number of cells in 'phy' property\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ for (index = 0; index < miphy_dev->nphys; index++)
+ if (phynode == miphy_dev->phys[index]->phy->dev.of_node) {
+ miphy_phy = miphy_dev->phys[index];
+ break;
+ }
+
+ if (!miphy_phy) {
+ dev_err(dev, "Failed to find appropriate phy\n");
+ return ERR_PTR(-EINVAL);
+ }
+
+ miphy_phy->type = args->args[0];
+
+ ret = miphy28lp_get_addr(miphy_phy);
+ if (ret < 0)
+ return ERR_PTR(ret);
+
+ return miphy_phy->phy;
+}
+
+static const struct phy_ops miphy28lp_ops = {
+ .init = miphy28lp_init,
+ .owner = THIS_MODULE,
+};
+
+static int miphy28lp_probe_resets(struct device_node *node,
+ struct miphy28lp_phy *miphy_phy)
+{
+ struct miphy28lp_dev *miphy_dev = miphy_phy->phydev;
+ int err;
+
+ miphy_phy->miphy_rst =
+ of_reset_control_get_shared(node, "miphy-sw-rst");
+
+ if (IS_ERR(miphy_phy->miphy_rst)) {
+ dev_err(miphy_dev->dev,
+ "miphy soft reset control not defined\n");
+ return PTR_ERR(miphy_phy->miphy_rst);
+ }
+
+ err = reset_control_deassert(miphy_phy->miphy_rst);
+ if (err) {
+ dev_err(miphy_dev->dev, "unable to bring out of miphy reset\n");
+ return err;
+ }
+
+ return 0;
+}
+
+static int miphy28lp_of_probe(struct device_node *np,
+ struct miphy28lp_phy *miphy_phy)
+{
+ int i;
+ u32 ctrlreg;
+
+ miphy_phy->osc_force_ext =
+ of_property_read_bool(np, "st,osc-force-ext");
+
+ miphy_phy->osc_rdy = of_property_read_bool(np, "st,osc-rdy");
+
+ miphy_phy->px_rx_pol_inv =
+ of_property_read_bool(np, "st,px_rx_pol_inv");
+
+ miphy_phy->ssc = of_property_read_bool(np, "st,ssc-on");
+
+ miphy_phy->tx_impedance =
+ of_property_read_bool(np, "st,tx-impedance-comp");
+
+ of_property_read_u32(np, "st,sata-gen", &miphy_phy->sata_gen);
+ if (!miphy_phy->sata_gen)
+ miphy_phy->sata_gen = SATA_GEN1;
+
+ for (i = 0; i < SYSCFG_REG_MAX; i++) {
+ if (!of_property_read_u32_index(np, "st,syscfg", i, &ctrlreg))
+ miphy_phy->syscfg_reg[i] = ctrlreg;
+ }
+
+ return 0;
+}
+
+static int miphy28lp_probe(struct platform_device *pdev)
+{
+ struct device_node *child, *np = pdev->dev.of_node;
+ struct miphy28lp_dev *miphy_dev;
+ struct phy_provider *provider;
+ struct phy *phy;
+ int ret, port = 0;
+
+ miphy_dev = devm_kzalloc(&pdev->dev, sizeof(*miphy_dev), GFP_KERNEL);
+ if (!miphy_dev)
+ return -ENOMEM;
+
+ miphy_dev->nphys = of_get_child_count(np);
+ miphy_dev->phys = devm_kcalloc(&pdev->dev, miphy_dev->nphys,
+ sizeof(*miphy_dev->phys), GFP_KERNEL);
+ if (!miphy_dev->phys)
+ return -ENOMEM;
+
+ miphy_dev->regmap = syscon_regmap_lookup_by_phandle(np, "st,syscfg");
+ if (IS_ERR(miphy_dev->regmap)) {
+ dev_err(miphy_dev->dev, "No syscfg phandle specified\n");
+ return PTR_ERR(miphy_dev->regmap);
+ }
+
+ miphy_dev->dev = &pdev->dev;
+
+ dev_set_drvdata(&pdev->dev, miphy_dev);
+
+ mutex_init(&miphy_dev->miphy_mutex);
+
+ for_each_child_of_node(np, child) {
+ struct miphy28lp_phy *miphy_phy;
+
+ miphy_phy = devm_kzalloc(&pdev->dev, sizeof(*miphy_phy),
+ GFP_KERNEL);
+ if (!miphy_phy) {
+ ret = -ENOMEM;
+ goto put_child;
+ }
+
+ miphy_dev->phys[port] = miphy_phy;
+
+ phy = devm_phy_create(&pdev->dev, child, &miphy28lp_ops);
+ if (IS_ERR(phy)) {
+ dev_err(&pdev->dev, "failed to create PHY\n");
+ ret = PTR_ERR(phy);
+ goto put_child;
+ }
+
+ miphy_dev->phys[port]->phy = phy;
+ miphy_dev->phys[port]->phydev = miphy_dev;
+
+ ret = miphy28lp_of_probe(child, miphy_phy);
+ if (ret)
+ goto put_child;
+
+ ret = miphy28lp_probe_resets(child, miphy_dev->phys[port]);
+ if (ret)
+ goto put_child;
+
+ phy_set_drvdata(phy, miphy_dev->phys[port]);
+ port++;
+
+ }
+
+ provider = devm_of_phy_provider_register(&pdev->dev, miphy28lp_xlate);
+ return PTR_ERR_OR_ZERO(provider);
+put_child:
+ of_node_put(child);
+ return ret;
+}
+
+static const struct of_device_id miphy28lp_of_match[] = {
+ {.compatible = "st,miphy28lp-phy", },
+ {},
+};
+
+MODULE_DEVICE_TABLE(of, miphy28lp_of_match);
+
+static struct platform_driver miphy28lp_driver = {
+ .probe = miphy28lp_probe,
+ .driver = {
+ .name = "miphy28lp-phy",
+ .of_match_table = miphy28lp_of_match,
+ }
+};
+
+module_platform_driver(miphy28lp_driver);
+
+MODULE_AUTHOR("Alexandre Torgue <alexandre.torgue@st.com>");
+MODULE_DESCRIPTION("STMicroelectronics miphy28lp driver");
+MODULE_LICENSE("GPL v2");