diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/pinctrl/qcom/pinctrl-spmi-mpp.c | 992 |
1 files changed, 992 insertions, 0 deletions
diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c b/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c new file mode 100644 index 000000000..6937157f5 --- /dev/null +++ b/drivers/pinctrl/qcom/pinctrl-spmi-mpp.c @@ -0,0 +1,992 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (c) 2012-2014, The Linux Foundation. All rights reserved. + */ + +#include <linux/gpio/driver.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_irq.h> +#include <linux/pinctrl/pinconf-generic.h> +#include <linux/pinctrl/pinconf.h> +#include <linux/pinctrl/pinmux.h> +#include <linux/platform_device.h> +#include <linux/regmap.h> +#include <linux/slab.h> +#include <linux/types.h> + +#include <dt-bindings/pinctrl/qcom,pmic-mpp.h> + +#include "../core.h" +#include "../pinctrl-utils.h" + +#define PMIC_MPP_ADDRESS_RANGE 0x100 + +/* + * Pull Up Values - it indicates whether a pull-up should be + * applied for bidirectional mode only. The hardware ignores the + * configuration when operating in other modes. + */ +#define PMIC_MPP_PULL_UP_0P6KOHM 0 +#define PMIC_MPP_PULL_UP_10KOHM 1 +#define PMIC_MPP_PULL_UP_30KOHM 2 +#define PMIC_MPP_PULL_UP_OPEN 3 + +/* type registers base address bases */ +#define PMIC_MPP_REG_TYPE 0x4 +#define PMIC_MPP_REG_SUBTYPE 0x5 + +/* mpp peripheral type and subtype values */ +#define PMIC_MPP_TYPE 0x11 +#define PMIC_MPP_SUBTYPE_4CH_NO_ANA_OUT 0x3 +#define PMIC_MPP_SUBTYPE_ULT_4CH_NO_ANA_OUT 0x4 +#define PMIC_MPP_SUBTYPE_4CH_NO_SINK 0x5 +#define PMIC_MPP_SUBTYPE_ULT_4CH_NO_SINK 0x6 +#define PMIC_MPP_SUBTYPE_4CH_FULL_FUNC 0x7 +#define PMIC_MPP_SUBTYPE_8CH_FULL_FUNC 0xf + +#define PMIC_MPP_REG_RT_STS 0x10 +#define PMIC_MPP_REG_RT_STS_VAL_MASK 0x1 + +/* control register base address bases */ +#define PMIC_MPP_REG_MODE_CTL 0x40 +#define PMIC_MPP_REG_DIG_VIN_CTL 0x41 +#define PMIC_MPP_REG_DIG_PULL_CTL 0x42 +#define PMIC_MPP_REG_DIG_IN_CTL 0x43 +#define PMIC_MPP_REG_EN_CTL 0x46 +#define PMIC_MPP_REG_AOUT_CTL 0x48 +#define PMIC_MPP_REG_AIN_CTL 0x4a +#define PMIC_MPP_REG_SINK_CTL 0x4c + +/* PMIC_MPP_REG_MODE_CTL */ +#define PMIC_MPP_REG_MODE_VALUE_MASK 0x1 +#define PMIC_MPP_REG_MODE_FUNCTION_SHIFT 1 +#define PMIC_MPP_REG_MODE_FUNCTION_MASK 0x7 +#define PMIC_MPP_REG_MODE_DIR_SHIFT 4 +#define PMIC_MPP_REG_MODE_DIR_MASK 0x7 + +/* PMIC_MPP_REG_DIG_VIN_CTL */ +#define PMIC_MPP_REG_VIN_SHIFT 0 +#define PMIC_MPP_REG_VIN_MASK 0x7 + +/* PMIC_MPP_REG_DIG_PULL_CTL */ +#define PMIC_MPP_REG_PULL_SHIFT 0 +#define PMIC_MPP_REG_PULL_MASK 0x7 + +/* PMIC_MPP_REG_EN_CTL */ +#define PMIC_MPP_REG_MASTER_EN_SHIFT 7 + +/* PMIC_MPP_REG_AIN_CTL */ +#define PMIC_MPP_REG_AIN_ROUTE_SHIFT 0 +#define PMIC_MPP_REG_AIN_ROUTE_MASK 0x7 + +#define PMIC_MPP_MODE_DIGITAL_INPUT 0 +#define PMIC_MPP_MODE_DIGITAL_OUTPUT 1 +#define PMIC_MPP_MODE_DIGITAL_BIDIR 2 +#define PMIC_MPP_MODE_ANALOG_BIDIR 3 +#define PMIC_MPP_MODE_ANALOG_INPUT 4 +#define PMIC_MPP_MODE_ANALOG_OUTPUT 5 +#define PMIC_MPP_MODE_CURRENT_SINK 6 + +#define PMIC_MPP_SELECTOR_NORMAL 0 +#define PMIC_MPP_SELECTOR_PAIRED 1 +#define PMIC_MPP_SELECTOR_DTEST_FIRST 4 + +#define PMIC_MPP_PHYSICAL_OFFSET 1 + +/* Qualcomm specific pin configurations */ +#define PMIC_MPP_CONF_AMUX_ROUTE (PIN_CONFIG_END + 1) +#define PMIC_MPP_CONF_ANALOG_LEVEL (PIN_CONFIG_END + 2) +#define PMIC_MPP_CONF_DTEST_SELECTOR (PIN_CONFIG_END + 3) +#define PMIC_MPP_CONF_PAIRED (PIN_CONFIG_END + 4) + +/** + * struct pmic_mpp_pad - keep current MPP settings + * @base: Address base in SPMI device. + * @is_enabled: Set to false when MPP should be put in high Z state. + * @out_value: Cached pin output value. + * @output_enabled: Set to true if MPP output logic is enabled. + * @input_enabled: Set to true if MPP input buffer logic is enabled. + * @paired: Pin operates in paired mode + * @has_pullup: Pin has support to configure pullup + * @num_sources: Number of power-sources supported by this MPP. + * @power_source: Current power-source used. + * @amux_input: Set the source for analog input. + * @aout_level: Analog output level + * @pullup: Pullup resistor value. Valid in Bidirectional mode only. + * @function: See pmic_mpp_functions[]. + * @drive_strength: Amount of current in sink mode + * @dtest: DTEST route selector + */ +struct pmic_mpp_pad { + u16 base; + bool is_enabled; + bool out_value; + bool output_enabled; + bool input_enabled; + bool paired; + bool has_pullup; + unsigned int num_sources; + unsigned int power_source; + unsigned int amux_input; + unsigned int aout_level; + unsigned int pullup; + unsigned int function; + unsigned int drive_strength; + unsigned int dtest; +}; + +struct pmic_mpp_state { + struct device *dev; + struct regmap *map; + struct pinctrl_dev *ctrl; + struct gpio_chip chip; + struct irq_chip irq; +}; + +static const struct pinconf_generic_params pmic_mpp_bindings[] = { + {"qcom,amux-route", PMIC_MPP_CONF_AMUX_ROUTE, 0}, + {"qcom,analog-level", PMIC_MPP_CONF_ANALOG_LEVEL, 0}, + {"qcom,dtest", PMIC_MPP_CONF_DTEST_SELECTOR, 0}, + {"qcom,paired", PMIC_MPP_CONF_PAIRED, 0}, +}; + +#ifdef CONFIG_DEBUG_FS +static const struct pin_config_item pmic_conf_items[] = { + PCONFDUMP(PMIC_MPP_CONF_AMUX_ROUTE, "analog mux", NULL, true), + PCONFDUMP(PMIC_MPP_CONF_ANALOG_LEVEL, "analog level", NULL, true), + PCONFDUMP(PMIC_MPP_CONF_DTEST_SELECTOR, "dtest", NULL, true), + PCONFDUMP(PMIC_MPP_CONF_PAIRED, "paired", NULL, false), +}; +#endif + +static const char *const pmic_mpp_groups[] = { + "mpp1", "mpp2", "mpp3", "mpp4", "mpp5", "mpp6", "mpp7", "mpp8", +}; + +#define PMIC_MPP_DIGITAL 0 +#define PMIC_MPP_ANALOG 1 +#define PMIC_MPP_SINK 2 + +static const char *const pmic_mpp_functions[] = { + "digital", "analog", "sink" +}; + +static int pmic_mpp_read(struct pmic_mpp_state *state, + struct pmic_mpp_pad *pad, unsigned int addr) +{ + unsigned int val; + int ret; + + ret = regmap_read(state->map, pad->base + addr, &val); + if (ret < 0) + dev_err(state->dev, "read 0x%x failed\n", addr); + else + ret = val; + + return ret; +} + +static int pmic_mpp_write(struct pmic_mpp_state *state, + struct pmic_mpp_pad *pad, unsigned int addr, + unsigned int val) +{ + int ret; + + ret = regmap_write(state->map, pad->base + addr, val); + if (ret < 0) + dev_err(state->dev, "write 0x%x failed\n", addr); + + return ret; +} + +static int pmic_mpp_get_groups_count(struct pinctrl_dev *pctldev) +{ + /* Every PIN is a group */ + return pctldev->desc->npins; +} + +static const char *pmic_mpp_get_group_name(struct pinctrl_dev *pctldev, + unsigned pin) +{ + return pctldev->desc->pins[pin].name; +} + +static int pmic_mpp_get_group_pins(struct pinctrl_dev *pctldev, + unsigned pin, + const unsigned **pins, unsigned *num_pins) +{ + *pins = &pctldev->desc->pins[pin].number; + *num_pins = 1; + return 0; +} + +static const struct pinctrl_ops pmic_mpp_pinctrl_ops = { + .get_groups_count = pmic_mpp_get_groups_count, + .get_group_name = pmic_mpp_get_group_name, + .get_group_pins = pmic_mpp_get_group_pins, + .dt_node_to_map = pinconf_generic_dt_node_to_map_group, + .dt_free_map = pinctrl_utils_free_map, +}; + +static int pmic_mpp_get_functions_count(struct pinctrl_dev *pctldev) +{ + return ARRAY_SIZE(pmic_mpp_functions); +} + +static const char *pmic_mpp_get_function_name(struct pinctrl_dev *pctldev, + unsigned function) +{ + return pmic_mpp_functions[function]; +} + +static int pmic_mpp_get_function_groups(struct pinctrl_dev *pctldev, + unsigned function, + const char *const **groups, + unsigned *const num_qgroups) +{ + *groups = pmic_mpp_groups; + *num_qgroups = pctldev->desc->npins; + return 0; +} + +static int pmic_mpp_write_mode_ctl(struct pmic_mpp_state *state, + struct pmic_mpp_pad *pad) +{ + unsigned int mode; + unsigned int sel; + unsigned int val; + unsigned int en; + + switch (pad->function) { + case PMIC_MPP_ANALOG: + if (pad->input_enabled && pad->output_enabled) + mode = PMIC_MPP_MODE_ANALOG_BIDIR; + else if (pad->input_enabled) + mode = PMIC_MPP_MODE_ANALOG_INPUT; + else + mode = PMIC_MPP_MODE_ANALOG_OUTPUT; + break; + case PMIC_MPP_DIGITAL: + if (pad->input_enabled && pad->output_enabled) + mode = PMIC_MPP_MODE_DIGITAL_BIDIR; + else if (pad->input_enabled) + mode = PMIC_MPP_MODE_DIGITAL_INPUT; + else + mode = PMIC_MPP_MODE_DIGITAL_OUTPUT; + break; + case PMIC_MPP_SINK: + default: + mode = PMIC_MPP_MODE_CURRENT_SINK; + break; + } + + if (pad->dtest) + sel = PMIC_MPP_SELECTOR_DTEST_FIRST + pad->dtest - 1; + else if (pad->paired) + sel = PMIC_MPP_SELECTOR_PAIRED; + else + sel = PMIC_MPP_SELECTOR_NORMAL; + + en = !!pad->out_value; + + val = mode << PMIC_MPP_REG_MODE_DIR_SHIFT | + sel << PMIC_MPP_REG_MODE_FUNCTION_SHIFT | + en; + + return pmic_mpp_write(state, pad, PMIC_MPP_REG_MODE_CTL, val); +} + +static int pmic_mpp_set_mux(struct pinctrl_dev *pctldev, unsigned function, + unsigned pin) +{ + struct pmic_mpp_state *state = pinctrl_dev_get_drvdata(pctldev); + struct pmic_mpp_pad *pad; + unsigned int val; + int ret; + + pad = pctldev->desc->pins[pin].drv_data; + + pad->function = function; + + ret = pmic_mpp_write_mode_ctl(state, pad); + if (ret < 0) + return ret; + + val = pad->is_enabled << PMIC_MPP_REG_MASTER_EN_SHIFT; + + return pmic_mpp_write(state, pad, PMIC_MPP_REG_EN_CTL, val); +} + +static const struct pinmux_ops pmic_mpp_pinmux_ops = { + .get_functions_count = pmic_mpp_get_functions_count, + .get_function_name = pmic_mpp_get_function_name, + .get_function_groups = pmic_mpp_get_function_groups, + .set_mux = pmic_mpp_set_mux, +}; + +static int pmic_mpp_config_get(struct pinctrl_dev *pctldev, + unsigned int pin, unsigned long *config) +{ + unsigned param = pinconf_to_config_param(*config); + struct pmic_mpp_pad *pad; + unsigned arg = 0; + + pad = pctldev->desc->pins[pin].drv_data; + + switch (param) { + case PIN_CONFIG_BIAS_DISABLE: + if (pad->pullup != PMIC_MPP_PULL_UP_OPEN) + return -EINVAL; + arg = 1; + break; + case PIN_CONFIG_BIAS_PULL_UP: + switch (pad->pullup) { + case PMIC_MPP_PULL_UP_0P6KOHM: + arg = 600; + break; + case PMIC_MPP_PULL_UP_10KOHM: + arg = 10000; + break; + case PMIC_MPP_PULL_UP_30KOHM: + arg = 30000; + break; + default: + return -EINVAL; + } + break; + case PIN_CONFIG_BIAS_HIGH_IMPEDANCE: + if (pad->is_enabled) + return -EINVAL; + arg = 1; + break; + case PIN_CONFIG_POWER_SOURCE: + arg = pad->power_source; + break; + case PIN_CONFIG_INPUT_ENABLE: + if (!pad->input_enabled) + return -EINVAL; + arg = 1; + break; + case PIN_CONFIG_OUTPUT: + arg = pad->out_value; + break; + case PMIC_MPP_CONF_DTEST_SELECTOR: + arg = pad->dtest; + break; + case PMIC_MPP_CONF_AMUX_ROUTE: + arg = pad->amux_input; + break; + case PMIC_MPP_CONF_PAIRED: + if (!pad->paired) + return -EINVAL; + arg = 1; + break; + case PIN_CONFIG_DRIVE_STRENGTH: + arg = pad->drive_strength; + break; + case PMIC_MPP_CONF_ANALOG_LEVEL: + arg = pad->aout_level; + break; + default: + return -EINVAL; + } + + /* Convert register value to pinconf value */ + *config = pinconf_to_config_packed(param, arg); + return 0; +} + +static int pmic_mpp_config_set(struct pinctrl_dev *pctldev, unsigned int pin, + unsigned long *configs, unsigned nconfs) +{ + struct pmic_mpp_state *state = pinctrl_dev_get_drvdata(pctldev); + struct pmic_mpp_pad *pad; + unsigned param, arg; + unsigned int val; + int i, ret; + + pad = pctldev->desc->pins[pin].drv_data; + + /* Make it possible to enable the pin, by not setting high impedance */ + pad->is_enabled = true; + + for (i = 0; i < nconfs; i++) { + param = pinconf_to_config_param(configs[i]); + arg = pinconf_to_config_argument(configs[i]); + + switch (param) { + case PIN_CONFIG_BIAS_DISABLE: + pad->pullup = PMIC_MPP_PULL_UP_OPEN; + break; + case PIN_CONFIG_BIAS_PULL_UP: + switch (arg) { + case 600: + pad->pullup = PMIC_MPP_PULL_UP_0P6KOHM; + break; + case 10000: + pad->pullup = PMIC_MPP_PULL_UP_10KOHM; + break; + case 30000: + pad->pullup = PMIC_MPP_PULL_UP_30KOHM; + break; + default: + return -EINVAL; + } + break; + case PIN_CONFIG_BIAS_HIGH_IMPEDANCE: + pad->is_enabled = false; + break; + case PIN_CONFIG_POWER_SOURCE: + if (arg >= pad->num_sources) + return -EINVAL; + pad->power_source = arg; + break; + case PIN_CONFIG_INPUT_ENABLE: + pad->input_enabled = arg ? true : false; + break; + case PIN_CONFIG_OUTPUT: + pad->output_enabled = true; + pad->out_value = arg; + break; + case PMIC_MPP_CONF_DTEST_SELECTOR: + pad->dtest = arg; + break; + case PIN_CONFIG_DRIVE_STRENGTH: + pad->drive_strength = arg; + break; + case PMIC_MPP_CONF_AMUX_ROUTE: + if (arg >= PMIC_MPP_AMUX_ROUTE_ABUS4) + return -EINVAL; + pad->amux_input = arg; + break; + case PMIC_MPP_CONF_ANALOG_LEVEL: + pad->aout_level = arg; + break; + case PMIC_MPP_CONF_PAIRED: + pad->paired = !!arg; + break; + default: + return -EINVAL; + } + } + + val = pad->power_source << PMIC_MPP_REG_VIN_SHIFT; + + ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_DIG_VIN_CTL, val); + if (ret < 0) + return ret; + + if (pad->has_pullup) { + val = pad->pullup << PMIC_MPP_REG_PULL_SHIFT; + + ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_DIG_PULL_CTL, + val); + if (ret < 0) + return ret; + } + + val = pad->amux_input & PMIC_MPP_REG_AIN_ROUTE_MASK; + + ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_AIN_CTL, val); + if (ret < 0) + return ret; + + ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_AOUT_CTL, pad->aout_level); + if (ret < 0) + return ret; + + ret = pmic_mpp_write_mode_ctl(state, pad); + if (ret < 0) + return ret; + + ret = pmic_mpp_write(state, pad, PMIC_MPP_REG_SINK_CTL, pad->drive_strength); + if (ret < 0) + return ret; + + val = pad->is_enabled << PMIC_MPP_REG_MASTER_EN_SHIFT; + + return pmic_mpp_write(state, pad, PMIC_MPP_REG_EN_CTL, val); +} + +static void pmic_mpp_config_dbg_show(struct pinctrl_dev *pctldev, + struct seq_file *s, unsigned pin) +{ + struct pmic_mpp_state *state = pinctrl_dev_get_drvdata(pctldev); + struct pmic_mpp_pad *pad; + int ret; + + static const char *const biases[] = { + "0.6kOhm", "10kOhm", "30kOhm", "Disabled" + }; + + pad = pctldev->desc->pins[pin].drv_data; + + seq_printf(s, " mpp%-2d:", pin + PMIC_MPP_PHYSICAL_OFFSET); + + if (!pad->is_enabled) { + seq_puts(s, " ---"); + } else { + + if (pad->input_enabled) { + ret = pmic_mpp_read(state, pad, PMIC_MPP_REG_RT_STS); + if (ret < 0) + return; + + ret &= PMIC_MPP_REG_RT_STS_VAL_MASK; + pad->out_value = ret; + } + + seq_printf(s, " %-4s", pad->output_enabled ? "out" : "in"); + seq_printf(s, " %-7s", pmic_mpp_functions[pad->function]); + seq_printf(s, " vin-%d", pad->power_source); + seq_printf(s, " %d", pad->aout_level); + if (pad->has_pullup) + seq_printf(s, " %-8s", biases[pad->pullup]); + seq_printf(s, " %-4s", pad->out_value ? "high" : "low"); + if (pad->dtest) + seq_printf(s, " dtest%d", pad->dtest); + if (pad->paired) + seq_puts(s, " paired"); + } +} + +static const struct pinconf_ops pmic_mpp_pinconf_ops = { + .is_generic = true, + .pin_config_group_get = pmic_mpp_config_get, + .pin_config_group_set = pmic_mpp_config_set, + .pin_config_group_dbg_show = pmic_mpp_config_dbg_show, +}; + +static int pmic_mpp_direction_input(struct gpio_chip *chip, unsigned pin) +{ + struct pmic_mpp_state *state = gpiochip_get_data(chip); + unsigned long config; + + config = pinconf_to_config_packed(PIN_CONFIG_INPUT_ENABLE, 1); + + return pmic_mpp_config_set(state->ctrl, pin, &config, 1); +} + +static int pmic_mpp_direction_output(struct gpio_chip *chip, + unsigned pin, int val) +{ + struct pmic_mpp_state *state = gpiochip_get_data(chip); + unsigned long config; + + config = pinconf_to_config_packed(PIN_CONFIG_OUTPUT, val); + + return pmic_mpp_config_set(state->ctrl, pin, &config, 1); +} + +static int pmic_mpp_get(struct gpio_chip *chip, unsigned pin) +{ + struct pmic_mpp_state *state = gpiochip_get_data(chip); + struct pmic_mpp_pad *pad; + int ret; + + pad = state->ctrl->desc->pins[pin].drv_data; + + if (pad->input_enabled) { + ret = pmic_mpp_read(state, pad, PMIC_MPP_REG_RT_STS); + if (ret < 0) + return ret; + + pad->out_value = ret & PMIC_MPP_REG_RT_STS_VAL_MASK; + } + + return !!pad->out_value; +} + +static void pmic_mpp_set(struct gpio_chip *chip, unsigned pin, int value) +{ + struct pmic_mpp_state *state = gpiochip_get_data(chip); + unsigned long config; + + config = pinconf_to_config_packed(PIN_CONFIG_OUTPUT, value); + + pmic_mpp_config_set(state->ctrl, pin, &config, 1); +} + +static int pmic_mpp_of_xlate(struct gpio_chip *chip, + const struct of_phandle_args *gpio_desc, + u32 *flags) +{ + if (chip->of_gpio_n_cells < 2) + return -EINVAL; + + if (flags) + *flags = gpio_desc->args[1]; + + return gpio_desc->args[0] - PMIC_MPP_PHYSICAL_OFFSET; +} + +static void pmic_mpp_dbg_show(struct seq_file *s, struct gpio_chip *chip) +{ + struct pmic_mpp_state *state = gpiochip_get_data(chip); + unsigned i; + + for (i = 0; i < chip->ngpio; i++) { + pmic_mpp_config_dbg_show(state->ctrl, s, i); + seq_puts(s, "\n"); + } +} + +static const struct gpio_chip pmic_mpp_gpio_template = { + .direction_input = pmic_mpp_direction_input, + .direction_output = pmic_mpp_direction_output, + .get = pmic_mpp_get, + .set = pmic_mpp_set, + .request = gpiochip_generic_request, + .free = gpiochip_generic_free, + .of_xlate = pmic_mpp_of_xlate, + .dbg_show = pmic_mpp_dbg_show, +}; + +static int pmic_mpp_populate(struct pmic_mpp_state *state, + struct pmic_mpp_pad *pad) +{ + int type, subtype, val, dir; + unsigned int sel; + + type = pmic_mpp_read(state, pad, PMIC_MPP_REG_TYPE); + if (type < 0) + return type; + + if (type != PMIC_MPP_TYPE) { + dev_err(state->dev, "incorrect block type 0x%x at 0x%x\n", + type, pad->base); + return -ENODEV; + } + + subtype = pmic_mpp_read(state, pad, PMIC_MPP_REG_SUBTYPE); + if (subtype < 0) + return subtype; + + switch (subtype) { + case PMIC_MPP_SUBTYPE_4CH_NO_ANA_OUT: + case PMIC_MPP_SUBTYPE_ULT_4CH_NO_ANA_OUT: + case PMIC_MPP_SUBTYPE_4CH_NO_SINK: + case PMIC_MPP_SUBTYPE_ULT_4CH_NO_SINK: + case PMIC_MPP_SUBTYPE_4CH_FULL_FUNC: + pad->num_sources = 4; + break; + case PMIC_MPP_SUBTYPE_8CH_FULL_FUNC: + pad->num_sources = 8; + break; + default: + dev_err(state->dev, "unknown MPP type 0x%x at 0x%x\n", + subtype, pad->base); + return -ENODEV; + } + + val = pmic_mpp_read(state, pad, PMIC_MPP_REG_MODE_CTL); + if (val < 0) + return val; + + pad->out_value = val & PMIC_MPP_REG_MODE_VALUE_MASK; + + dir = val >> PMIC_MPP_REG_MODE_DIR_SHIFT; + dir &= PMIC_MPP_REG_MODE_DIR_MASK; + + switch (dir) { + case PMIC_MPP_MODE_DIGITAL_INPUT: + pad->input_enabled = true; + pad->output_enabled = false; + pad->function = PMIC_MPP_DIGITAL; + break; + case PMIC_MPP_MODE_DIGITAL_OUTPUT: + pad->input_enabled = false; + pad->output_enabled = true; + pad->function = PMIC_MPP_DIGITAL; + break; + case PMIC_MPP_MODE_DIGITAL_BIDIR: + pad->input_enabled = true; + pad->output_enabled = true; + pad->function = PMIC_MPP_DIGITAL; + break; + case PMIC_MPP_MODE_ANALOG_BIDIR: + pad->input_enabled = true; + pad->output_enabled = true; + pad->function = PMIC_MPP_ANALOG; + break; + case PMIC_MPP_MODE_ANALOG_INPUT: + pad->input_enabled = true; + pad->output_enabled = false; + pad->function = PMIC_MPP_ANALOG; + break; + case PMIC_MPP_MODE_ANALOG_OUTPUT: + pad->input_enabled = false; + pad->output_enabled = true; + pad->function = PMIC_MPP_ANALOG; + break; + case PMIC_MPP_MODE_CURRENT_SINK: + pad->input_enabled = false; + pad->output_enabled = true; + pad->function = PMIC_MPP_SINK; + break; + default: + dev_err(state->dev, "unknown MPP direction\n"); + return -ENODEV; + } + + sel = val >> PMIC_MPP_REG_MODE_FUNCTION_SHIFT; + sel &= PMIC_MPP_REG_MODE_FUNCTION_MASK; + + if (sel >= PMIC_MPP_SELECTOR_DTEST_FIRST) + pad->dtest = sel + 1; + else if (sel == PMIC_MPP_SELECTOR_PAIRED) + pad->paired = true; + + val = pmic_mpp_read(state, pad, PMIC_MPP_REG_DIG_VIN_CTL); + if (val < 0) + return val; + + pad->power_source = val >> PMIC_MPP_REG_VIN_SHIFT; + pad->power_source &= PMIC_MPP_REG_VIN_MASK; + + if (subtype != PMIC_MPP_SUBTYPE_ULT_4CH_NO_ANA_OUT && + subtype != PMIC_MPP_SUBTYPE_ULT_4CH_NO_SINK) { + val = pmic_mpp_read(state, pad, PMIC_MPP_REG_DIG_PULL_CTL); + if (val < 0) + return val; + + pad->pullup = val >> PMIC_MPP_REG_PULL_SHIFT; + pad->pullup &= PMIC_MPP_REG_PULL_MASK; + pad->has_pullup = true; + } + + val = pmic_mpp_read(state, pad, PMIC_MPP_REG_AIN_CTL); + if (val < 0) + return val; + + pad->amux_input = val >> PMIC_MPP_REG_AIN_ROUTE_SHIFT; + pad->amux_input &= PMIC_MPP_REG_AIN_ROUTE_MASK; + + val = pmic_mpp_read(state, pad, PMIC_MPP_REG_SINK_CTL); + if (val < 0) + return val; + + pad->drive_strength = val; + + val = pmic_mpp_read(state, pad, PMIC_MPP_REG_AOUT_CTL); + if (val < 0) + return val; + + pad->aout_level = val; + + val = pmic_mpp_read(state, pad, PMIC_MPP_REG_EN_CTL); + if (val < 0) + return val; + + pad->is_enabled = !!val; + + return 0; +} + +static int pmic_mpp_domain_translate(struct irq_domain *domain, + struct irq_fwspec *fwspec, + unsigned long *hwirq, + unsigned int *type) +{ + struct pmic_mpp_state *state = container_of(domain->host_data, + struct pmic_mpp_state, + chip); + + if (fwspec->param_count != 2 || + fwspec->param[0] < 1 || fwspec->param[0] > state->chip.ngpio) + return -EINVAL; + + *hwirq = fwspec->param[0] - PMIC_MPP_PHYSICAL_OFFSET; + *type = fwspec->param[1]; + + return 0; +} + +static unsigned int pmic_mpp_child_offset_to_irq(struct gpio_chip *chip, + unsigned int offset) +{ + return offset + PMIC_MPP_PHYSICAL_OFFSET; +} + +static int pmic_mpp_child_to_parent_hwirq(struct gpio_chip *chip, + unsigned int child_hwirq, + unsigned int child_type, + unsigned int *parent_hwirq, + unsigned int *parent_type) +{ + *parent_hwirq = child_hwirq + 0xc0; + *parent_type = child_type; + + return 0; +} + +static int pmic_mpp_probe(struct platform_device *pdev) +{ + struct irq_domain *parent_domain; + struct device_node *parent_node; + struct device *dev = &pdev->dev; + struct pinctrl_pin_desc *pindesc; + struct pinctrl_desc *pctrldesc; + struct pmic_mpp_pad *pad, *pads; + struct pmic_mpp_state *state; + struct gpio_irq_chip *girq; + int ret, npins, i; + u32 reg; + + ret = of_property_read_u32(dev->of_node, "reg", ®); + if (ret < 0) { + dev_err(dev, "missing base address"); + return ret; + } + + npins = (uintptr_t) device_get_match_data(&pdev->dev); + + BUG_ON(npins > ARRAY_SIZE(pmic_mpp_groups)); + + state = devm_kzalloc(dev, sizeof(*state), GFP_KERNEL); + if (!state) + return -ENOMEM; + + platform_set_drvdata(pdev, state); + + state->dev = &pdev->dev; + state->map = dev_get_regmap(dev->parent, NULL); + + pindesc = devm_kcalloc(dev, npins, sizeof(*pindesc), GFP_KERNEL); + if (!pindesc) + return -ENOMEM; + + pads = devm_kcalloc(dev, npins, sizeof(*pads), GFP_KERNEL); + if (!pads) + return -ENOMEM; + + pctrldesc = devm_kzalloc(dev, sizeof(*pctrldesc), GFP_KERNEL); + if (!pctrldesc) + return -ENOMEM; + + pctrldesc->pctlops = &pmic_mpp_pinctrl_ops; + pctrldesc->pmxops = &pmic_mpp_pinmux_ops; + pctrldesc->confops = &pmic_mpp_pinconf_ops; + pctrldesc->owner = THIS_MODULE; + pctrldesc->name = dev_name(dev); + pctrldesc->pins = pindesc; + pctrldesc->npins = npins; + + pctrldesc->num_custom_params = ARRAY_SIZE(pmic_mpp_bindings); + pctrldesc->custom_params = pmic_mpp_bindings; +#ifdef CONFIG_DEBUG_FS + pctrldesc->custom_conf_items = pmic_conf_items; +#endif + + for (i = 0; i < npins; i++, pindesc++) { + pad = &pads[i]; + pindesc->drv_data = pad; + pindesc->number = i; + pindesc->name = pmic_mpp_groups[i]; + + pad->base = reg + i * PMIC_MPP_ADDRESS_RANGE; + + ret = pmic_mpp_populate(state, pad); + if (ret < 0) + return ret; + } + + state->chip = pmic_mpp_gpio_template; + state->chip.parent = dev; + state->chip.base = -1; + state->chip.ngpio = npins; + state->chip.label = dev_name(dev); + state->chip.of_gpio_n_cells = 2; + state->chip.can_sleep = false; + + state->ctrl = devm_pinctrl_register(dev, pctrldesc, state); + if (IS_ERR(state->ctrl)) + return PTR_ERR(state->ctrl); + + parent_node = of_irq_find_parent(state->dev->of_node); + if (!parent_node) + return -ENXIO; + + parent_domain = irq_find_host(parent_node); + of_node_put(parent_node); + if (!parent_domain) + return -ENXIO; + + state->irq.name = "spmi-mpp", + state->irq.irq_ack = irq_chip_ack_parent, + state->irq.irq_mask = irq_chip_mask_parent, + state->irq.irq_unmask = irq_chip_unmask_parent, + state->irq.irq_set_type = irq_chip_set_type_parent, + state->irq.irq_set_wake = irq_chip_set_wake_parent, + state->irq.flags = IRQCHIP_MASK_ON_SUSPEND, + + girq = &state->chip.irq; + girq->chip = &state->irq; + girq->default_type = IRQ_TYPE_NONE; + girq->handler = handle_level_irq; + girq->fwnode = of_node_to_fwnode(state->dev->of_node); + girq->parent_domain = parent_domain; + girq->child_to_parent_hwirq = pmic_mpp_child_to_parent_hwirq; + girq->populate_parent_alloc_arg = gpiochip_populate_parent_fwspec_fourcell; + girq->child_offset_to_irq = pmic_mpp_child_offset_to_irq; + girq->child_irq_domain_ops.translate = pmic_mpp_domain_translate; + + ret = gpiochip_add_data(&state->chip, state); + if (ret) { + dev_err(state->dev, "can't add gpio chip\n"); + return ret; + } + + ret = gpiochip_add_pin_range(&state->chip, dev_name(dev), 0, 0, npins); + if (ret) { + dev_err(dev, "failed to add pin range\n"); + goto err_range; + } + + return 0; + +err_range: + gpiochip_remove(&state->chip); + return ret; +} + +static int pmic_mpp_remove(struct platform_device *pdev) +{ + struct pmic_mpp_state *state = platform_get_drvdata(pdev); + + gpiochip_remove(&state->chip); + return 0; +} + +static const struct of_device_id pmic_mpp_of_match[] = { + { .compatible = "qcom,pm8019-mpp", .data = (void *) 6 }, + { .compatible = "qcom,pm8226-mpp", .data = (void *) 8 }, + { .compatible = "qcom,pm8841-mpp", .data = (void *) 4 }, + { .compatible = "qcom,pm8916-mpp", .data = (void *) 4 }, + { .compatible = "qcom,pm8941-mpp", .data = (void *) 8 }, + { .compatible = "qcom,pm8950-mpp", .data = (void *) 4 }, + { .compatible = "qcom,pmi8950-mpp", .data = (void *) 4 }, + { .compatible = "qcom,pm8994-mpp", .data = (void *) 8 }, + { .compatible = "qcom,pma8084-mpp", .data = (void *) 8 }, + { .compatible = "qcom,pmi8994-mpp", .data = (void *) 4 }, + { }, +}; + +MODULE_DEVICE_TABLE(of, pmic_mpp_of_match); + +static struct platform_driver pmic_mpp_driver = { + .driver = { + .name = "qcom-spmi-mpp", + .of_match_table = pmic_mpp_of_match, + }, + .probe = pmic_mpp_probe, + .remove = pmic_mpp_remove, +}; + +module_platform_driver(pmic_mpp_driver); + +MODULE_AUTHOR("Ivan T. Ivanov <iivanov@mm-sol.com>"); +MODULE_DESCRIPTION("Qualcomm SPMI PMIC MPP pin control driver"); +MODULE_ALIAS("platform:qcom-spmi-mpp"); +MODULE_LICENSE("GPL v2"); |