diff options
Diffstat (limited to '')
-rw-r--r-- | drivers/scsi/isci/phy.c | 1484 |
1 files changed, 1484 insertions, 0 deletions
diff --git a/drivers/scsi/isci/phy.c b/drivers/scsi/isci/phy.c new file mode 100644 index 000000000..aa8787343 --- /dev/null +++ b/drivers/scsi/isci/phy.c @@ -0,0 +1,1484 @@ +/* + * This file is provided under a dual BSD/GPLv2 license. When using or + * redistributing this file, you may do so under either license. + * + * GPL LICENSE SUMMARY + * + * Copyright(c) 2008 - 2011 Intel Corporation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of version 2 of the GNU General Public License as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + * The full GNU General Public License is included in this distribution + * in the file called LICENSE.GPL. + * + * BSD LICENSE + * + * Copyright(c) 2008 - 2011 Intel Corporation. All rights reserved. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in + * the documentation and/or other materials provided with the + * distribution. + * * Neither the name of Intel Corporation nor the names of its + * contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, + * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT + * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, + * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY + * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT + * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + */ + +#include "isci.h" +#include "host.h" +#include "phy.h" +#include "scu_event_codes.h" +#include "probe_roms.h" + +#undef C +#define C(a) (#a) +static const char *phy_state_name(enum sci_phy_states state) +{ + static const char * const strings[] = PHY_STATES; + + return strings[state]; +} +#undef C + +/* Maximum arbitration wait time in micro-seconds */ +#define SCIC_SDS_PHY_MAX_ARBITRATION_WAIT_TIME (700) + +enum sas_linkrate sci_phy_linkrate(struct isci_phy *iphy) +{ + return iphy->max_negotiated_speed; +} + +static struct isci_host *phy_to_host(struct isci_phy *iphy) +{ + struct isci_phy *table = iphy - iphy->phy_index; + struct isci_host *ihost = container_of(table, typeof(*ihost), phys[0]); + + return ihost; +} + +static struct device *sciphy_to_dev(struct isci_phy *iphy) +{ + return &phy_to_host(iphy)->pdev->dev; +} + +static enum sci_status +sci_phy_transport_layer_initialization(struct isci_phy *iphy, + struct scu_transport_layer_registers __iomem *reg) +{ + u32 tl_control; + + iphy->transport_layer_registers = reg; + + writel(SCIC_SDS_REMOTE_NODE_CONTEXT_INVALID_INDEX, + &iphy->transport_layer_registers->stp_rni); + + /* + * Hardware team recommends that we enable the STP prefetch for all + * transports + */ + tl_control = readl(&iphy->transport_layer_registers->control); + tl_control |= SCU_TLCR_GEN_BIT(STP_WRITE_DATA_PREFETCH); + writel(tl_control, &iphy->transport_layer_registers->control); + + return SCI_SUCCESS; +} + +static enum sci_status +sci_phy_link_layer_initialization(struct isci_phy *iphy, + struct scu_link_layer_registers __iomem *llr) +{ + struct isci_host *ihost = iphy->owning_port->owning_controller; + struct sci_phy_user_params *phy_user; + struct sci_phy_oem_params *phy_oem; + int phy_idx = iphy->phy_index; + struct sci_phy_cap phy_cap; + u32 phy_configuration; + u32 parity_check = 0; + u32 parity_count = 0; + u32 llctl, link_rate; + u32 clksm_value = 0; + u32 sp_timeouts = 0; + + phy_user = &ihost->user_parameters.phys[phy_idx]; + phy_oem = &ihost->oem_parameters.phys[phy_idx]; + iphy->link_layer_registers = llr; + + /* Set our IDENTIFY frame data */ + #define SCI_END_DEVICE 0x01 + + writel(SCU_SAS_TIID_GEN_BIT(SMP_INITIATOR) | + SCU_SAS_TIID_GEN_BIT(SSP_INITIATOR) | + SCU_SAS_TIID_GEN_BIT(STP_INITIATOR) | + SCU_SAS_TIID_GEN_BIT(DA_SATA_HOST) | + SCU_SAS_TIID_GEN_VAL(DEVICE_TYPE, SCI_END_DEVICE), + &llr->transmit_identification); + + /* Write the device SAS Address */ + writel(0xFEDCBA98, &llr->sas_device_name_high); + writel(phy_idx, &llr->sas_device_name_low); + + /* Write the source SAS Address */ + writel(phy_oem->sas_address.high, &llr->source_sas_address_high); + writel(phy_oem->sas_address.low, &llr->source_sas_address_low); + + /* Clear and Set the PHY Identifier */ + writel(0, &llr->identify_frame_phy_id); + writel(SCU_SAS_TIPID_GEN_VALUE(ID, phy_idx), &llr->identify_frame_phy_id); + + /* Change the initial state of the phy configuration register */ + phy_configuration = readl(&llr->phy_configuration); + + /* Hold OOB state machine in reset */ + phy_configuration |= SCU_SAS_PCFG_GEN_BIT(OOB_RESET); + writel(phy_configuration, &llr->phy_configuration); + + /* Configure the SNW capabilities */ + phy_cap.all = 0; + phy_cap.start = 1; + phy_cap.gen3_no_ssc = 1; + phy_cap.gen2_no_ssc = 1; + phy_cap.gen1_no_ssc = 1; + if (ihost->oem_parameters.controller.do_enable_ssc) { + struct scu_afe_registers __iomem *afe = &ihost->scu_registers->afe; + struct scu_afe_transceiver __iomem *xcvr = &afe->scu_afe_xcvr[phy_idx]; + struct isci_pci_info *pci_info = to_pci_info(ihost->pdev); + bool en_sas = false; + bool en_sata = false; + u32 sas_type = 0; + u32 sata_spread = 0x2; + u32 sas_spread = 0x2; + + phy_cap.gen3_ssc = 1; + phy_cap.gen2_ssc = 1; + phy_cap.gen1_ssc = 1; + + if (pci_info->orom->hdr.version < ISCI_ROM_VER_1_1) + en_sas = en_sata = true; + else { + sata_spread = ihost->oem_parameters.controller.ssc_sata_tx_spread_level; + sas_spread = ihost->oem_parameters.controller.ssc_sas_tx_spread_level; + + if (sata_spread) + en_sata = true; + + if (sas_spread) { + en_sas = true; + sas_type = ihost->oem_parameters.controller.ssc_sas_tx_type; + } + + } + + if (en_sas) { + u32 reg; + + reg = readl(&xcvr->afe_xcvr_control0); + reg |= (0x00100000 | (sas_type << 19)); + writel(reg, &xcvr->afe_xcvr_control0); + + reg = readl(&xcvr->afe_tx_ssc_control); + reg |= sas_spread << 8; + writel(reg, &xcvr->afe_tx_ssc_control); + } + + if (en_sata) { + u32 reg; + + reg = readl(&xcvr->afe_tx_ssc_control); + reg |= sata_spread; + writel(reg, &xcvr->afe_tx_ssc_control); + + reg = readl(&llr->stp_control); + reg |= 1 << 12; + writel(reg, &llr->stp_control); + } + } + + /* The SAS specification indicates that the phy_capabilities that + * are transmitted shall have an even parity. Calculate the parity. + */ + parity_check = phy_cap.all; + while (parity_check != 0) { + if (parity_check & 0x1) + parity_count++; + parity_check >>= 1; + } + + /* If parity indicates there are an odd number of bits set, then + * set the parity bit to 1 in the phy capabilities. + */ + if ((parity_count % 2) != 0) + phy_cap.parity = 1; + + writel(phy_cap.all, &llr->phy_capabilities); + + /* Set the enable spinup period but disable the ability to send + * notify enable spinup + */ + writel(SCU_ENSPINUP_GEN_VAL(COUNT, + phy_user->notify_enable_spin_up_insertion_frequency), + &llr->notify_enable_spinup_control); + + /* Write the ALIGN Insertion Ferequency for connected phy and + * inpendent of connected state + */ + clksm_value = SCU_ALIGN_INSERTION_FREQUENCY_GEN_VAL(CONNECTED, + phy_user->in_connection_align_insertion_frequency); + + clksm_value |= SCU_ALIGN_INSERTION_FREQUENCY_GEN_VAL(GENERAL, + phy_user->align_insertion_frequency); + + writel(clksm_value, &llr->clock_skew_management); + + if (is_c0(ihost->pdev) || is_c1(ihost->pdev)) { + writel(0x04210400, &llr->afe_lookup_table_control); + writel(0x020A7C05, &llr->sas_primitive_timeout); + } else + writel(0x02108421, &llr->afe_lookup_table_control); + + llctl = SCU_SAS_LLCTL_GEN_VAL(NO_OUTBOUND_TASK_TIMEOUT, + (u8)ihost->user_parameters.no_outbound_task_timeout); + + switch (phy_user->max_speed_generation) { + case SCIC_SDS_PARM_GEN3_SPEED: + link_rate = SCU_SAS_LINK_LAYER_CONTROL_MAX_LINK_RATE_GEN3; + break; + case SCIC_SDS_PARM_GEN2_SPEED: + link_rate = SCU_SAS_LINK_LAYER_CONTROL_MAX_LINK_RATE_GEN2; + break; + default: + link_rate = SCU_SAS_LINK_LAYER_CONTROL_MAX_LINK_RATE_GEN1; + break; + } + llctl |= SCU_SAS_LLCTL_GEN_VAL(MAX_LINK_RATE, link_rate); + writel(llctl, &llr->link_layer_control); + + sp_timeouts = readl(&llr->sas_phy_timeouts); + + /* Clear the default 0x36 (54us) RATE_CHANGE timeout value. */ + sp_timeouts &= ~SCU_SAS_PHYTOV_GEN_VAL(RATE_CHANGE, 0xFF); + + /* Set RATE_CHANGE timeout value to 0x3B (59us). This ensures SCU can + * lock with 3Gb drive when SCU max rate is set to 1.5Gb. + */ + sp_timeouts |= SCU_SAS_PHYTOV_GEN_VAL(RATE_CHANGE, 0x3B); + + writel(sp_timeouts, &llr->sas_phy_timeouts); + + if (is_a2(ihost->pdev)) { + /* Program the max ARB time for the PHY to 700us so we + * inter-operate with the PMC expander which shuts down + * PHYs if the expander PHY generates too many breaks. + * This time value will guarantee that the initiator PHY + * will generate the break. + */ + writel(SCIC_SDS_PHY_MAX_ARBITRATION_WAIT_TIME, + &llr->maximum_arbitration_wait_timer_timeout); + } + + /* Disable link layer hang detection, rely on the OS timeout for + * I/O timeouts. + */ + writel(0, &llr->link_layer_hang_detection_timeout); + + /* We can exit the initial state to the stopped state */ + sci_change_state(&iphy->sm, SCI_PHY_STOPPED); + + return SCI_SUCCESS; +} + +static void phy_sata_timeout(struct timer_list *t) +{ + struct sci_timer *tmr = from_timer(tmr, t, timer); + struct isci_phy *iphy = container_of(tmr, typeof(*iphy), sata_timer); + struct isci_host *ihost = iphy->owning_port->owning_controller; + unsigned long flags; + + spin_lock_irqsave(&ihost->scic_lock, flags); + + if (tmr->cancel) + goto done; + + dev_dbg(sciphy_to_dev(iphy), + "%s: SCIC SDS Phy 0x%p did not receive signature fis before " + "timeout.\n", + __func__, + iphy); + + sci_change_state(&iphy->sm, SCI_PHY_STARTING); +done: + spin_unlock_irqrestore(&ihost->scic_lock, flags); +} + +/** + * phy_get_non_dummy_port() - This method returns the port currently containing + * this phy. If the phy is currently contained by the dummy port, then the phy + * is considered to not be part of a port. + * + * @iphy: This parameter specifies the phy for which to retrieve the + * containing port. + * + * This method returns a handle to a port that contains the supplied phy. + * NULL This value is returned if the phy is not part of a real + * port (i.e. it's contained in the dummy port). !NULL All other + * values indicate a handle/pointer to the port containing the phy. + */ +struct isci_port *phy_get_non_dummy_port(struct isci_phy *iphy) +{ + struct isci_port *iport = iphy->owning_port; + + if (iport->physical_port_index == SCIC_SDS_DUMMY_PORT) + return NULL; + + return iphy->owning_port; +} + +/* + * sci_phy_set_port() - This method will assign a port to the phy object. + */ +void sci_phy_set_port( + struct isci_phy *iphy, + struct isci_port *iport) +{ + iphy->owning_port = iport; + + if (iphy->bcn_received_while_port_unassigned) { + iphy->bcn_received_while_port_unassigned = false; + sci_port_broadcast_change_received(iphy->owning_port, iphy); + } +} + +enum sci_status sci_phy_initialize(struct isci_phy *iphy, + struct scu_transport_layer_registers __iomem *tl, + struct scu_link_layer_registers __iomem *ll) +{ + /* Perfrom the initialization of the TL hardware */ + sci_phy_transport_layer_initialization(iphy, tl); + + /* Perofrm the initialization of the PE hardware */ + sci_phy_link_layer_initialization(iphy, ll); + + /* There is nothing that needs to be done in this state just + * transition to the stopped state + */ + sci_change_state(&iphy->sm, SCI_PHY_STOPPED); + + return SCI_SUCCESS; +} + +/** + * sci_phy_setup_transport() - This method assigns the direct attached device ID for this phy. + * + * @iphy: The phy for which the direct attached device id is to + * be assigned. + * @device_id: The direct attached device ID to assign to the phy. + * This will either be the RNi for the device or an invalid RNi if there + * is no current device assigned to the phy. + */ +void sci_phy_setup_transport(struct isci_phy *iphy, u32 device_id) +{ + u32 tl_control; + + writel(device_id, &iphy->transport_layer_registers->stp_rni); + + /* + * The read should guarantee that the first write gets posted + * before the next write + */ + tl_control = readl(&iphy->transport_layer_registers->control); + tl_control |= SCU_TLCR_GEN_BIT(CLEAR_TCI_NCQ_MAPPING_TABLE); + writel(tl_control, &iphy->transport_layer_registers->control); +} + +static void sci_phy_suspend(struct isci_phy *iphy) +{ + u32 scu_sas_pcfg_value; + + scu_sas_pcfg_value = + readl(&iphy->link_layer_registers->phy_configuration); + scu_sas_pcfg_value |= SCU_SAS_PCFG_GEN_BIT(SUSPEND_PROTOCOL_ENGINE); + writel(scu_sas_pcfg_value, + &iphy->link_layer_registers->phy_configuration); + + sci_phy_setup_transport(iphy, SCIC_SDS_REMOTE_NODE_CONTEXT_INVALID_INDEX); +} + +void sci_phy_resume(struct isci_phy *iphy) +{ + u32 scu_sas_pcfg_value; + + scu_sas_pcfg_value = + readl(&iphy->link_layer_registers->phy_configuration); + scu_sas_pcfg_value &= ~SCU_SAS_PCFG_GEN_BIT(SUSPEND_PROTOCOL_ENGINE); + writel(scu_sas_pcfg_value, + &iphy->link_layer_registers->phy_configuration); +} + +void sci_phy_get_sas_address(struct isci_phy *iphy, struct sci_sas_address *sas) +{ + sas->high = readl(&iphy->link_layer_registers->source_sas_address_high); + sas->low = readl(&iphy->link_layer_registers->source_sas_address_low); +} + +void sci_phy_get_attached_sas_address(struct isci_phy *iphy, struct sci_sas_address *sas) +{ + struct sas_identify_frame *iaf; + + iaf = &iphy->frame_rcvd.iaf; + memcpy(sas, iaf->sas_addr, SAS_ADDR_SIZE); +} + +void sci_phy_get_protocols(struct isci_phy *iphy, struct sci_phy_proto *proto) +{ + proto->all = readl(&iphy->link_layer_registers->transmit_identification); +} + +enum sci_status sci_phy_start(struct isci_phy *iphy) +{ + enum sci_phy_states state = iphy->sm.current_state_id; + + if (state != SCI_PHY_STOPPED) { + dev_dbg(sciphy_to_dev(iphy), "%s: in wrong state: %s\n", + __func__, phy_state_name(state)); + return SCI_FAILURE_INVALID_STATE; + } + + sci_change_state(&iphy->sm, SCI_PHY_STARTING); + return SCI_SUCCESS; +} + +enum sci_status sci_phy_stop(struct isci_phy *iphy) +{ + enum sci_phy_states state = iphy->sm.current_state_id; + + switch (state) { + case SCI_PHY_SUB_INITIAL: + case SCI_PHY_SUB_AWAIT_OSSP_EN: + case SCI_PHY_SUB_AWAIT_SAS_SPEED_EN: + case SCI_PHY_SUB_AWAIT_SAS_POWER: + case SCI_PHY_SUB_AWAIT_SATA_POWER: + case SCI_PHY_SUB_AWAIT_SATA_PHY_EN: + case SCI_PHY_SUB_AWAIT_SATA_SPEED_EN: + case SCI_PHY_SUB_AWAIT_SIG_FIS_UF: + case SCI_PHY_SUB_FINAL: + case SCI_PHY_READY: + break; + default: + dev_dbg(sciphy_to_dev(iphy), "%s: in wrong state: %s\n", + __func__, phy_state_name(state)); + return SCI_FAILURE_INVALID_STATE; + } + + sci_change_state(&iphy->sm, SCI_PHY_STOPPED); + return SCI_SUCCESS; +} + +enum sci_status sci_phy_reset(struct isci_phy *iphy) +{ + enum sci_phy_states state = iphy->sm.current_state_id; + + if (state != SCI_PHY_READY) { + dev_dbg(sciphy_to_dev(iphy), "%s: in wrong state: %s\n", + __func__, phy_state_name(state)); + return SCI_FAILURE_INVALID_STATE; + } + + sci_change_state(&iphy->sm, SCI_PHY_RESETTING); + return SCI_SUCCESS; +} + +enum sci_status sci_phy_consume_power_handler(struct isci_phy *iphy) +{ + enum sci_phy_states state = iphy->sm.current_state_id; + + switch (state) { + case SCI_PHY_SUB_AWAIT_SAS_POWER: { + u32 enable_spinup; + + enable_spinup = readl(&iphy->link_layer_registers->notify_enable_spinup_control); + enable_spinup |= SCU_ENSPINUP_GEN_BIT(ENABLE); + writel(enable_spinup, &iphy->link_layer_registers->notify_enable_spinup_control); + + /* Change state to the final state this substate machine has run to completion */ + sci_change_state(&iphy->sm, SCI_PHY_SUB_FINAL); + + return SCI_SUCCESS; + } + case SCI_PHY_SUB_AWAIT_SATA_POWER: { + u32 scu_sas_pcfg_value; + + /* Release the spinup hold state and reset the OOB state machine */ + scu_sas_pcfg_value = + readl(&iphy->link_layer_registers->phy_configuration); + scu_sas_pcfg_value &= + ~(SCU_SAS_PCFG_GEN_BIT(SATA_SPINUP_HOLD) | SCU_SAS_PCFG_GEN_BIT(OOB_ENABLE)); + scu_sas_pcfg_value |= SCU_SAS_PCFG_GEN_BIT(OOB_RESET); + writel(scu_sas_pcfg_value, + &iphy->link_layer_registers->phy_configuration); + + /* Now restart the OOB operation */ + scu_sas_pcfg_value &= ~SCU_SAS_PCFG_GEN_BIT(OOB_RESET); + scu_sas_pcfg_value |= SCU_SAS_PCFG_GEN_BIT(OOB_ENABLE); + writel(scu_sas_pcfg_value, + &iphy->link_layer_registers->phy_configuration); + + /* Change state to the final state this substate machine has run to completion */ + sci_change_state(&iphy->sm, SCI_PHY_SUB_AWAIT_SATA_PHY_EN); + + return SCI_SUCCESS; + } + default: + dev_dbg(sciphy_to_dev(iphy), "%s: in wrong state: %s\n", + __func__, phy_state_name(state)); + return SCI_FAILURE_INVALID_STATE; + } +} + +static void sci_phy_start_sas_link_training(struct isci_phy *iphy) +{ + /* continue the link training for the phy as if it were a SAS PHY + * instead of a SATA PHY. This is done because the completion queue had a SAS + * PHY DETECTED event when the state machine was expecting a SATA PHY event. + */ + u32 phy_control; + + phy_control = readl(&iphy->link_layer_registers->phy_configuration); + phy_control |= SCU_SAS_PCFG_GEN_BIT(SATA_SPINUP_HOLD); + writel(phy_control, + &iphy->link_layer_registers->phy_configuration); + + sci_change_state(&iphy->sm, SCI_PHY_SUB_AWAIT_SAS_SPEED_EN); + + iphy->protocol = SAS_PROTOCOL_SSP; +} + +static void sci_phy_start_sata_link_training(struct isci_phy *iphy) +{ + /* This method continues the link training for the phy as if it were a SATA PHY + * instead of a SAS PHY. This is done because the completion queue had a SATA + * SPINUP HOLD event when the state machine was expecting a SAS PHY event. none + */ + sci_change_state(&iphy->sm, SCI_PHY_SUB_AWAIT_SATA_POWER); + + iphy->protocol = SAS_PROTOCOL_SATA; +} + +/** + * sci_phy_complete_link_training - perform processing common to + * all protocols upon completion of link training. + * @iphy: This parameter specifies the phy object for which link training + * has completed. + * @max_link_rate: This parameter specifies the maximum link rate to be + * associated with this phy. + * @next_state: This parameter specifies the next state for the phy's starting + * sub-state machine. + * + */ +static void sci_phy_complete_link_training(struct isci_phy *iphy, + enum sas_linkrate max_link_rate, + u32 next_state) +{ + iphy->max_negotiated_speed = max_link_rate; + + sci_change_state(&iphy->sm, next_state); +} + +static const char *phy_event_name(u32 event_code) +{ + switch (scu_get_event_code(event_code)) { + case SCU_EVENT_PORT_SELECTOR_DETECTED: + return "port selector"; + case SCU_EVENT_SENT_PORT_SELECTION: + return "port selection"; + case SCU_EVENT_HARD_RESET_TRANSMITTED: + return "tx hard reset"; + case SCU_EVENT_HARD_RESET_RECEIVED: + return "rx hard reset"; + case SCU_EVENT_RECEIVED_IDENTIFY_TIMEOUT: + return "identify timeout"; + case SCU_EVENT_LINK_FAILURE: + return "link fail"; + case SCU_EVENT_SATA_SPINUP_HOLD: + return "sata spinup hold"; + case SCU_EVENT_SAS_15_SSC: + case SCU_EVENT_SAS_15: + return "sas 1.5"; + case SCU_EVENT_SAS_30_SSC: + case SCU_EVENT_SAS_30: + return "sas 3.0"; + case SCU_EVENT_SAS_60_SSC: + case SCU_EVENT_SAS_60: + return "sas 6.0"; + case SCU_EVENT_SATA_15_SSC: + case SCU_EVENT_SATA_15: + return "sata 1.5"; + case SCU_EVENT_SATA_30_SSC: + case SCU_EVENT_SATA_30: + return "sata 3.0"; + case SCU_EVENT_SATA_60_SSC: + case SCU_EVENT_SATA_60: + return "sata 6.0"; + case SCU_EVENT_SAS_PHY_DETECTED: + return "sas detect"; + case SCU_EVENT_SATA_PHY_DETECTED: + return "sata detect"; + default: + return "unknown"; + } +} + +#define phy_event_dbg(iphy, state, code) \ + dev_dbg(sciphy_to_dev(iphy), "phy-%d:%d: %s event: %s (%x)\n", \ + phy_to_host(iphy)->id, iphy->phy_index, \ + phy_state_name(state), phy_event_name(code), code) + +#define phy_event_warn(iphy, state, code) \ + dev_warn(sciphy_to_dev(iphy), "phy-%d:%d: %s event: %s (%x)\n", \ + phy_to_host(iphy)->id, iphy->phy_index, \ + phy_state_name(state), phy_event_name(code), code) + + +static void scu_link_layer_set_txcomsas_timeout(struct isci_phy *iphy, u32 timeout) +{ + u32 val; + + /* Extend timeout */ + val = readl(&iphy->link_layer_registers->transmit_comsas_signal); + val &= ~SCU_SAS_LLTXCOMSAS_GEN_VAL(NEGTIME, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_MASK); + val |= SCU_SAS_LLTXCOMSAS_GEN_VAL(NEGTIME, timeout); + + writel(val, &iphy->link_layer_registers->transmit_comsas_signal); +} + +enum sci_status sci_phy_event_handler(struct isci_phy *iphy, u32 event_code) +{ + enum sci_phy_states state = iphy->sm.current_state_id; + + switch (state) { + case SCI_PHY_SUB_AWAIT_OSSP_EN: + switch (scu_get_event_code(event_code)) { + case SCU_EVENT_SAS_PHY_DETECTED: + sci_phy_start_sas_link_training(iphy); + iphy->is_in_link_training = true; + break; + case SCU_EVENT_SATA_SPINUP_HOLD: + sci_phy_start_sata_link_training(iphy); + iphy->is_in_link_training = true; + break; + case SCU_EVENT_RECEIVED_IDENTIFY_TIMEOUT: + /* Extend timeout value */ + scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_EXTENDED); + + /* Start the oob/sn state machine over again */ + sci_change_state(&iphy->sm, SCI_PHY_STARTING); + break; + default: + phy_event_dbg(iphy, state, event_code); + return SCI_FAILURE; + } + return SCI_SUCCESS; + case SCI_PHY_SUB_AWAIT_SAS_SPEED_EN: + switch (scu_get_event_code(event_code)) { + case SCU_EVENT_SAS_PHY_DETECTED: + /* + * Why is this being reported again by the controller? + * We would re-enter this state so just stay here */ + break; + case SCU_EVENT_SAS_15: + case SCU_EVENT_SAS_15_SSC: + sci_phy_complete_link_training(iphy, SAS_LINK_RATE_1_5_GBPS, + SCI_PHY_SUB_AWAIT_IAF_UF); + break; + case SCU_EVENT_SAS_30: + case SCU_EVENT_SAS_30_SSC: + sci_phy_complete_link_training(iphy, SAS_LINK_RATE_3_0_GBPS, + SCI_PHY_SUB_AWAIT_IAF_UF); + break; + case SCU_EVENT_SAS_60: + case SCU_EVENT_SAS_60_SSC: + sci_phy_complete_link_training(iphy, SAS_LINK_RATE_6_0_GBPS, + SCI_PHY_SUB_AWAIT_IAF_UF); + break; + case SCU_EVENT_SATA_SPINUP_HOLD: + /* + * We were doing SAS PHY link training and received a SATA PHY event + * continue OOB/SN as if this were a SATA PHY */ + sci_phy_start_sata_link_training(iphy); + break; + case SCU_EVENT_LINK_FAILURE: + /* Change the timeout value to default */ + scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_DEFAULT); + + /* Link failure change state back to the starting state */ + sci_change_state(&iphy->sm, SCI_PHY_STARTING); + break; + case SCU_EVENT_RECEIVED_IDENTIFY_TIMEOUT: + /* Extend the timeout value */ + scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_EXTENDED); + + /* Start the oob/sn state machine over again */ + sci_change_state(&iphy->sm, SCI_PHY_STARTING); + break; + default: + phy_event_warn(iphy, state, event_code); + return SCI_FAILURE; + } + return SCI_SUCCESS; + case SCI_PHY_SUB_AWAIT_IAF_UF: + switch (scu_get_event_code(event_code)) { + case SCU_EVENT_SAS_PHY_DETECTED: + /* Backup the state machine */ + sci_phy_start_sas_link_training(iphy); + break; + case SCU_EVENT_SATA_SPINUP_HOLD: + /* We were doing SAS PHY link training and received a + * SATA PHY event continue OOB/SN as if this were a + * SATA PHY + */ + sci_phy_start_sata_link_training(iphy); + break; + case SCU_EVENT_RECEIVED_IDENTIFY_TIMEOUT: + /* Extend the timeout value */ + scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_EXTENDED); + + /* Start the oob/sn state machine over again */ + sci_change_state(&iphy->sm, SCI_PHY_STARTING); + break; + case SCU_EVENT_LINK_FAILURE: + scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_DEFAULT); + fallthrough; + case SCU_EVENT_HARD_RESET_RECEIVED: + /* Start the oob/sn state machine over again */ + sci_change_state(&iphy->sm, SCI_PHY_STARTING); + break; + default: + phy_event_warn(iphy, state, event_code); + return SCI_FAILURE; + } + return SCI_SUCCESS; + case SCI_PHY_SUB_AWAIT_SAS_POWER: + switch (scu_get_event_code(event_code)) { + case SCU_EVENT_LINK_FAILURE: + /* Change the timeout value to default */ + scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_DEFAULT); + + /* Link failure change state back to the starting state */ + sci_change_state(&iphy->sm, SCI_PHY_STARTING); + break; + default: + phy_event_warn(iphy, state, event_code); + return SCI_FAILURE; + } + return SCI_SUCCESS; + case SCI_PHY_SUB_AWAIT_SATA_POWER: + switch (scu_get_event_code(event_code)) { + case SCU_EVENT_LINK_FAILURE: + /* Change the timeout value to default */ + scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_DEFAULT); + + /* Link failure change state back to the starting state */ + sci_change_state(&iphy->sm, SCI_PHY_STARTING); + break; + case SCU_EVENT_SATA_SPINUP_HOLD: + /* These events are received every 10ms and are + * expected while in this state + */ + break; + + case SCU_EVENT_SAS_PHY_DETECTED: + /* There has been a change in the phy type before OOB/SN for the + * SATA finished start down the SAS link traning path. + */ + sci_phy_start_sas_link_training(iphy); + break; + + default: + phy_event_warn(iphy, state, event_code); + return SCI_FAILURE; + } + return SCI_SUCCESS; + case SCI_PHY_SUB_AWAIT_SATA_PHY_EN: + switch (scu_get_event_code(event_code)) { + case SCU_EVENT_LINK_FAILURE: + /* Change the timeout value to default */ + scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_DEFAULT); + + /* Link failure change state back to the starting state */ + sci_change_state(&iphy->sm, SCI_PHY_STARTING); + break; + case SCU_EVENT_SATA_SPINUP_HOLD: + /* These events might be received since we dont know how many may be in + * the completion queue while waiting for power + */ + break; + case SCU_EVENT_SATA_PHY_DETECTED: + iphy->protocol = SAS_PROTOCOL_SATA; + + /* We have received the SATA PHY notification change state */ + sci_change_state(&iphy->sm, SCI_PHY_SUB_AWAIT_SATA_SPEED_EN); + break; + case SCU_EVENT_SAS_PHY_DETECTED: + /* There has been a change in the phy type before OOB/SN for the + * SATA finished start down the SAS link traning path. + */ + sci_phy_start_sas_link_training(iphy); + break; + default: + phy_event_warn(iphy, state, event_code); + return SCI_FAILURE; + } + return SCI_SUCCESS; + case SCI_PHY_SUB_AWAIT_SATA_SPEED_EN: + switch (scu_get_event_code(event_code)) { + case SCU_EVENT_SATA_PHY_DETECTED: + /* + * The hardware reports multiple SATA PHY detected events + * ignore the extras */ + break; + case SCU_EVENT_SATA_15: + case SCU_EVENT_SATA_15_SSC: + sci_phy_complete_link_training(iphy, SAS_LINK_RATE_1_5_GBPS, + SCI_PHY_SUB_AWAIT_SIG_FIS_UF); + break; + case SCU_EVENT_SATA_30: + case SCU_EVENT_SATA_30_SSC: + sci_phy_complete_link_training(iphy, SAS_LINK_RATE_3_0_GBPS, + SCI_PHY_SUB_AWAIT_SIG_FIS_UF); + break; + case SCU_EVENT_SATA_60: + case SCU_EVENT_SATA_60_SSC: + sci_phy_complete_link_training(iphy, SAS_LINK_RATE_6_0_GBPS, + SCI_PHY_SUB_AWAIT_SIG_FIS_UF); + break; + case SCU_EVENT_LINK_FAILURE: + /* Change the timeout value to default */ + scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_DEFAULT); + + /* Link failure change state back to the starting state */ + sci_change_state(&iphy->sm, SCI_PHY_STARTING); + break; + case SCU_EVENT_SAS_PHY_DETECTED: + /* + * There has been a change in the phy type before OOB/SN for the + * SATA finished start down the SAS link traning path. */ + sci_phy_start_sas_link_training(iphy); + break; + default: + phy_event_warn(iphy, state, event_code); + return SCI_FAILURE; + } + + return SCI_SUCCESS; + case SCI_PHY_SUB_AWAIT_SIG_FIS_UF: + switch (scu_get_event_code(event_code)) { + case SCU_EVENT_SATA_PHY_DETECTED: + /* Backup the state machine */ + sci_change_state(&iphy->sm, SCI_PHY_SUB_AWAIT_SATA_SPEED_EN); + break; + + case SCU_EVENT_LINK_FAILURE: + /* Change the timeout value to default */ + scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_DEFAULT); + + /* Link failure change state back to the starting state */ + sci_change_state(&iphy->sm, SCI_PHY_STARTING); + break; + + default: + phy_event_warn(iphy, state, event_code); + return SCI_FAILURE; + } + return SCI_SUCCESS; + case SCI_PHY_READY: + switch (scu_get_event_code(event_code)) { + case SCU_EVENT_LINK_FAILURE: + /* Set default timeout */ + scu_link_layer_set_txcomsas_timeout(iphy, SCU_SAS_LINK_LAYER_TXCOMSAS_NEGTIME_DEFAULT); + + /* Link failure change state back to the starting state */ + sci_change_state(&iphy->sm, SCI_PHY_STARTING); + break; + case SCU_EVENT_BROADCAST_CHANGE: + case SCU_EVENT_BROADCAST_SES: + case SCU_EVENT_BROADCAST_RESERVED0: + case SCU_EVENT_BROADCAST_RESERVED1: + case SCU_EVENT_BROADCAST_EXPANDER: + case SCU_EVENT_BROADCAST_AEN: + /* Broadcast change received. Notify the port. */ + if (phy_get_non_dummy_port(iphy) != NULL) + sci_port_broadcast_change_received(iphy->owning_port, iphy); + else + iphy->bcn_received_while_port_unassigned = true; + break; + case SCU_EVENT_BROADCAST_RESERVED3: + case SCU_EVENT_BROADCAST_RESERVED4: + default: + phy_event_warn(iphy, state, event_code); + return SCI_FAILURE_INVALID_STATE; + } + return SCI_SUCCESS; + case SCI_PHY_RESETTING: + switch (scu_get_event_code(event_code)) { + case SCU_EVENT_HARD_RESET_TRANSMITTED: + /* Link failure change state back to the starting state */ + sci_change_state(&iphy->sm, SCI_PHY_STARTING); + break; + default: + phy_event_warn(iphy, state, event_code); + return SCI_FAILURE_INVALID_STATE; + } + return SCI_SUCCESS; + default: + dev_dbg(sciphy_to_dev(iphy), "%s: in wrong state: %s\n", + __func__, phy_state_name(state)); + return SCI_FAILURE_INVALID_STATE; + } +} + +enum sci_status sci_phy_frame_handler(struct isci_phy *iphy, u32 frame_index) +{ + enum sci_phy_states state = iphy->sm.current_state_id; + struct isci_host *ihost = iphy->owning_port->owning_controller; + enum sci_status result; + unsigned long flags; + + switch (state) { + case SCI_PHY_SUB_AWAIT_IAF_UF: { + u32 *frame_words; + struct sas_identify_frame iaf; + + result = sci_unsolicited_frame_control_get_header(&ihost->uf_control, + frame_index, + (void **)&frame_words); + + if (result != SCI_SUCCESS) + return result; + + sci_swab32_cpy(&iaf, frame_words, sizeof(iaf) / sizeof(u32)); + if (iaf.frame_type == 0) { + u32 state; + + spin_lock_irqsave(&iphy->sas_phy.frame_rcvd_lock, flags); + memcpy(&iphy->frame_rcvd.iaf, &iaf, sizeof(iaf)); + spin_unlock_irqrestore(&iphy->sas_phy.frame_rcvd_lock, flags); + if (iaf.smp_tport) { + /* We got the IAF for an expander PHY go to the final + * state since there are no power requirements for + * expander phys. + */ + state = SCI_PHY_SUB_FINAL; + } else { + /* We got the IAF we can now go to the await spinup + * semaphore state + */ + state = SCI_PHY_SUB_AWAIT_SAS_POWER; + } + sci_change_state(&iphy->sm, state); + result = SCI_SUCCESS; + } else + dev_warn(sciphy_to_dev(iphy), + "%s: PHY starting substate machine received " + "unexpected frame id %x\n", + __func__, frame_index); + + sci_controller_release_frame(ihost, frame_index); + return result; + } + case SCI_PHY_SUB_AWAIT_SIG_FIS_UF: { + struct dev_to_host_fis *frame_header; + u32 *fis_frame_data; + + result = sci_unsolicited_frame_control_get_header(&ihost->uf_control, + frame_index, + (void **)&frame_header); + + if (result != SCI_SUCCESS) + return result; + + if ((frame_header->fis_type == FIS_REGD2H) && + !(frame_header->status & ATA_BUSY)) { + sci_unsolicited_frame_control_get_buffer(&ihost->uf_control, + frame_index, + (void **)&fis_frame_data); + + spin_lock_irqsave(&iphy->sas_phy.frame_rcvd_lock, flags); + sci_controller_copy_sata_response(&iphy->frame_rcvd.fis, + frame_header, + fis_frame_data); + spin_unlock_irqrestore(&iphy->sas_phy.frame_rcvd_lock, flags); + + /* got IAF we can now go to the await spinup semaphore state */ + sci_change_state(&iphy->sm, SCI_PHY_SUB_FINAL); + + result = SCI_SUCCESS; + } else + dev_warn(sciphy_to_dev(iphy), + "%s: PHY starting substate machine received " + "unexpected frame id %x\n", + __func__, frame_index); + + /* Regardless of the result we are done with this frame with it */ + sci_controller_release_frame(ihost, frame_index); + + return result; + } + default: + dev_dbg(sciphy_to_dev(iphy), "%s: in wrong state: %s\n", + __func__, phy_state_name(state)); + return SCI_FAILURE_INVALID_STATE; + } + +} + +static void sci_phy_starting_initial_substate_enter(struct sci_base_state_machine *sm) +{ + struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm); + + /* This is just an temporary state go off to the starting state */ + sci_change_state(&iphy->sm, SCI_PHY_SUB_AWAIT_OSSP_EN); +} + +static void sci_phy_starting_await_sas_power_substate_enter(struct sci_base_state_machine *sm) +{ + struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm); + struct isci_host *ihost = iphy->owning_port->owning_controller; + + sci_controller_power_control_queue_insert(ihost, iphy); +} + +static void sci_phy_starting_await_sas_power_substate_exit(struct sci_base_state_machine *sm) +{ + struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm); + struct isci_host *ihost = iphy->owning_port->owning_controller; + + sci_controller_power_control_queue_remove(ihost, iphy); +} + +static void sci_phy_starting_await_sata_power_substate_enter(struct sci_base_state_machine *sm) +{ + struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm); + struct isci_host *ihost = iphy->owning_port->owning_controller; + + sci_controller_power_control_queue_insert(ihost, iphy); +} + +static void sci_phy_starting_await_sata_power_substate_exit(struct sci_base_state_machine *sm) +{ + struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm); + struct isci_host *ihost = iphy->owning_port->owning_controller; + + sci_controller_power_control_queue_remove(ihost, iphy); +} + +static void sci_phy_starting_await_sata_phy_substate_enter(struct sci_base_state_machine *sm) +{ + struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm); + + sci_mod_timer(&iphy->sata_timer, SCIC_SDS_SATA_LINK_TRAINING_TIMEOUT); +} + +static void sci_phy_starting_await_sata_phy_substate_exit(struct sci_base_state_machine *sm) +{ + struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm); + + sci_del_timer(&iphy->sata_timer); +} + +static void sci_phy_starting_await_sata_speed_substate_enter(struct sci_base_state_machine *sm) +{ + struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm); + + sci_mod_timer(&iphy->sata_timer, SCIC_SDS_SATA_LINK_TRAINING_TIMEOUT); +} + +static void sci_phy_starting_await_sata_speed_substate_exit(struct sci_base_state_machine *sm) +{ + struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm); + + sci_del_timer(&iphy->sata_timer); +} + +static void sci_phy_starting_await_sig_fis_uf_substate_enter(struct sci_base_state_machine *sm) +{ + struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm); + + if (sci_port_link_detected(iphy->owning_port, iphy)) { + + /* + * Clear the PE suspend condition so we can actually + * receive SIG FIS + * The hardware will not respond to the XRDY until the PE + * suspend condition is cleared. + */ + sci_phy_resume(iphy); + + sci_mod_timer(&iphy->sata_timer, + SCIC_SDS_SIGNATURE_FIS_TIMEOUT); + } else + iphy->is_in_link_training = false; +} + +static void sci_phy_starting_await_sig_fis_uf_substate_exit(struct sci_base_state_machine *sm) +{ + struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm); + + sci_del_timer(&iphy->sata_timer); +} + +static void sci_phy_starting_final_substate_enter(struct sci_base_state_machine *sm) +{ + struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm); + + /* State machine has run to completion so exit out and change + * the base state machine to the ready state + */ + sci_change_state(&iphy->sm, SCI_PHY_READY); +} + +/** + * scu_link_layer_stop_protocol_engine() + * @iphy: This is the struct isci_phy object to stop. + * + * This method will stop the struct isci_phy object. This does not reset the + * protocol engine it just suspends it and places it in a state where it will + * not cause the end device to power up. none + */ +static void scu_link_layer_stop_protocol_engine( + struct isci_phy *iphy) +{ + u32 scu_sas_pcfg_value; + u32 enable_spinup_value; + + /* Suspend the protocol engine and place it in a sata spinup hold state */ + scu_sas_pcfg_value = + readl(&iphy->link_layer_registers->phy_configuration); + scu_sas_pcfg_value |= + (SCU_SAS_PCFG_GEN_BIT(OOB_RESET) | + SCU_SAS_PCFG_GEN_BIT(SUSPEND_PROTOCOL_ENGINE) | + SCU_SAS_PCFG_GEN_BIT(SATA_SPINUP_HOLD)); + writel(scu_sas_pcfg_value, + &iphy->link_layer_registers->phy_configuration); + + /* Disable the notify enable spinup primitives */ + enable_spinup_value = readl(&iphy->link_layer_registers->notify_enable_spinup_control); + enable_spinup_value &= ~SCU_ENSPINUP_GEN_BIT(ENABLE); + writel(enable_spinup_value, &iphy->link_layer_registers->notify_enable_spinup_control); +} + +static void scu_link_layer_start_oob(struct isci_phy *iphy) +{ + struct scu_link_layer_registers __iomem *ll = iphy->link_layer_registers; + u32 val; + + /** Reset OOB sequence - start */ + val = readl(&ll->phy_configuration); + val &= ~(SCU_SAS_PCFG_GEN_BIT(OOB_RESET) | + SCU_SAS_PCFG_GEN_BIT(OOB_ENABLE) | + SCU_SAS_PCFG_GEN_BIT(HARD_RESET)); + writel(val, &ll->phy_configuration); + readl(&ll->phy_configuration); /* flush */ + /** Reset OOB sequence - end */ + + /** Start OOB sequence - start */ + val = readl(&ll->phy_configuration); + val |= SCU_SAS_PCFG_GEN_BIT(OOB_ENABLE); + writel(val, &ll->phy_configuration); + readl(&ll->phy_configuration); /* flush */ + /** Start OOB sequence - end */ +} + +/** + * scu_link_layer_tx_hard_reset() + * @iphy: This is the struct isci_phy object to stop. + * + * This method will transmit a hard reset request on the specified phy. The SCU + * hardware requires that we reset the OOB state machine and set the hard reset + * bit in the phy configuration register. We then must start OOB over with the + * hard reset bit set. + */ +static void scu_link_layer_tx_hard_reset( + struct isci_phy *iphy) +{ + u32 phy_configuration_value; + + /* + * SAS Phys must wait for the HARD_RESET_TX event notification to transition + * to the starting state. */ + phy_configuration_value = + readl(&iphy->link_layer_registers->phy_configuration); + phy_configuration_value &= ~(SCU_SAS_PCFG_GEN_BIT(OOB_ENABLE)); + phy_configuration_value |= + (SCU_SAS_PCFG_GEN_BIT(HARD_RESET) | + SCU_SAS_PCFG_GEN_BIT(OOB_RESET)); + writel(phy_configuration_value, + &iphy->link_layer_registers->phy_configuration); + + /* Now take the OOB state machine out of reset */ + phy_configuration_value |= SCU_SAS_PCFG_GEN_BIT(OOB_ENABLE); + phy_configuration_value &= ~SCU_SAS_PCFG_GEN_BIT(OOB_RESET); + writel(phy_configuration_value, + &iphy->link_layer_registers->phy_configuration); +} + +static void sci_phy_stopped_state_enter(struct sci_base_state_machine *sm) +{ + struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm); + struct isci_port *iport = iphy->owning_port; + struct isci_host *ihost = iport->owning_controller; + + /* + * @todo We need to get to the controller to place this PE in a + * reset state + */ + sci_del_timer(&iphy->sata_timer); + + scu_link_layer_stop_protocol_engine(iphy); + + if (iphy->sm.previous_state_id != SCI_PHY_INITIAL) + sci_controller_link_down(ihost, phy_get_non_dummy_port(iphy), iphy); +} + +static void sci_phy_starting_state_enter(struct sci_base_state_machine *sm) +{ + struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm); + struct isci_port *iport = iphy->owning_port; + struct isci_host *ihost = iport->owning_controller; + + scu_link_layer_stop_protocol_engine(iphy); + scu_link_layer_start_oob(iphy); + + /* We don't know what kind of phy we are going to be just yet */ + iphy->protocol = SAS_PROTOCOL_NONE; + iphy->bcn_received_while_port_unassigned = false; + + if (iphy->sm.previous_state_id == SCI_PHY_READY) + sci_controller_link_down(ihost, phy_get_non_dummy_port(iphy), iphy); + + sci_change_state(&iphy->sm, SCI_PHY_SUB_INITIAL); +} + +static void sci_phy_ready_state_enter(struct sci_base_state_machine *sm) +{ + struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm); + struct isci_port *iport = iphy->owning_port; + struct isci_host *ihost = iport->owning_controller; + + sci_controller_link_up(ihost, phy_get_non_dummy_port(iphy), iphy); +} + +static void sci_phy_ready_state_exit(struct sci_base_state_machine *sm) +{ + struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm); + + sci_phy_suspend(iphy); +} + +static void sci_phy_resetting_state_enter(struct sci_base_state_machine *sm) +{ + struct isci_phy *iphy = container_of(sm, typeof(*iphy), sm); + + /* The phy is being reset, therefore deactivate it from the port. In + * the resetting state we don't notify the user regarding link up and + * link down notifications + */ + sci_port_deactivate_phy(iphy->owning_port, iphy, false); + + if (iphy->protocol == SAS_PROTOCOL_SSP) { + scu_link_layer_tx_hard_reset(iphy); + } else { + /* The SCU does not need to have a discrete reset state so + * just go back to the starting state. + */ + sci_change_state(&iphy->sm, SCI_PHY_STARTING); + } +} + +static const struct sci_base_state sci_phy_state_table[] = { + [SCI_PHY_INITIAL] = { }, + [SCI_PHY_STOPPED] = { + .enter_state = sci_phy_stopped_state_enter, + }, + [SCI_PHY_STARTING] = { + .enter_state = sci_phy_starting_state_enter, + }, + [SCI_PHY_SUB_INITIAL] = { + .enter_state = sci_phy_starting_initial_substate_enter, + }, + [SCI_PHY_SUB_AWAIT_OSSP_EN] = { }, + [SCI_PHY_SUB_AWAIT_SAS_SPEED_EN] = { }, + [SCI_PHY_SUB_AWAIT_IAF_UF] = { }, + [SCI_PHY_SUB_AWAIT_SAS_POWER] = { + .enter_state = sci_phy_starting_await_sas_power_substate_enter, + .exit_state = sci_phy_starting_await_sas_power_substate_exit, + }, + [SCI_PHY_SUB_AWAIT_SATA_POWER] = { + .enter_state = sci_phy_starting_await_sata_power_substate_enter, + .exit_state = sci_phy_starting_await_sata_power_substate_exit + }, + [SCI_PHY_SUB_AWAIT_SATA_PHY_EN] = { + .enter_state = sci_phy_starting_await_sata_phy_substate_enter, + .exit_state = sci_phy_starting_await_sata_phy_substate_exit + }, + [SCI_PHY_SUB_AWAIT_SATA_SPEED_EN] = { + .enter_state = sci_phy_starting_await_sata_speed_substate_enter, + .exit_state = sci_phy_starting_await_sata_speed_substate_exit + }, + [SCI_PHY_SUB_AWAIT_SIG_FIS_UF] = { + .enter_state = sci_phy_starting_await_sig_fis_uf_substate_enter, + .exit_state = sci_phy_starting_await_sig_fis_uf_substate_exit + }, + [SCI_PHY_SUB_FINAL] = { + .enter_state = sci_phy_starting_final_substate_enter, + }, + [SCI_PHY_READY] = { + .enter_state = sci_phy_ready_state_enter, + .exit_state = sci_phy_ready_state_exit, + }, + [SCI_PHY_RESETTING] = { + .enter_state = sci_phy_resetting_state_enter, + }, + [SCI_PHY_FINAL] = { }, +}; + +void sci_phy_construct(struct isci_phy *iphy, + struct isci_port *iport, u8 phy_index) +{ + sci_init_sm(&iphy->sm, sci_phy_state_table, SCI_PHY_INITIAL); + + /* Copy the rest of the input data to our locals */ + iphy->owning_port = iport; + iphy->phy_index = phy_index; + iphy->bcn_received_while_port_unassigned = false; + iphy->protocol = SAS_PROTOCOL_NONE; + iphy->link_layer_registers = NULL; + iphy->max_negotiated_speed = SAS_LINK_RATE_UNKNOWN; + + /* Create the SIGNATURE FIS Timeout timer for this phy */ + sci_init_timer(&iphy->sata_timer, phy_sata_timeout); +} + +void isci_phy_init(struct isci_phy *iphy, struct isci_host *ihost, int index) +{ + struct sci_oem_params *oem = &ihost->oem_parameters; + u64 sci_sas_addr; + __be64 sas_addr; + + sci_sas_addr = oem->phys[index].sas_address.high; + sci_sas_addr <<= 32; + sci_sas_addr |= oem->phys[index].sas_address.low; + sas_addr = cpu_to_be64(sci_sas_addr); + memcpy(iphy->sas_addr, &sas_addr, sizeof(sas_addr)); + + iphy->sas_phy.enabled = 0; + iphy->sas_phy.id = index; + iphy->sas_phy.sas_addr = &iphy->sas_addr[0]; + iphy->sas_phy.frame_rcvd = (u8 *)&iphy->frame_rcvd; + iphy->sas_phy.ha = &ihost->sas_ha; + iphy->sas_phy.lldd_phy = iphy; + iphy->sas_phy.enabled = 1; + iphy->sas_phy.class = SAS; + iphy->sas_phy.iproto = SAS_PROTOCOL_ALL; + iphy->sas_phy.tproto = 0; + iphy->sas_phy.type = PHY_TYPE_PHYSICAL; + iphy->sas_phy.role = PHY_ROLE_INITIATOR; + iphy->sas_phy.oob_mode = OOB_NOT_CONNECTED; + iphy->sas_phy.linkrate = SAS_LINK_RATE_UNKNOWN; + memset(&iphy->frame_rcvd, 0, sizeof(iphy->frame_rcvd)); +} + + +/** + * isci_phy_control() - This function is one of the SAS Domain Template + * functions. This is a phy management function. + * @sas_phy: This parameter specifies the sphy being controlled. + * @func: This parameter specifies the phy control function being invoked. + * @buf: This parameter is specific to the phy function being invoked. + * + * status, zero indicates success. + */ +int isci_phy_control(struct asd_sas_phy *sas_phy, + enum phy_func func, + void *buf) +{ + int ret = 0; + struct isci_phy *iphy = sas_phy->lldd_phy; + struct asd_sas_port *port = sas_phy->port; + struct isci_host *ihost = sas_phy->ha->lldd_ha; + unsigned long flags; + + dev_dbg(&ihost->pdev->dev, + "%s: phy %p; func %d; buf %p; isci phy %p, port %p\n", + __func__, sas_phy, func, buf, iphy, port); + + switch (func) { + case PHY_FUNC_DISABLE: + spin_lock_irqsave(&ihost->scic_lock, flags); + scu_link_layer_start_oob(iphy); + sci_phy_stop(iphy); + spin_unlock_irqrestore(&ihost->scic_lock, flags); + break; + + case PHY_FUNC_LINK_RESET: + spin_lock_irqsave(&ihost->scic_lock, flags); + scu_link_layer_start_oob(iphy); + sci_phy_stop(iphy); + sci_phy_start(iphy); + spin_unlock_irqrestore(&ihost->scic_lock, flags); + break; + + case PHY_FUNC_HARD_RESET: + if (!port) + return -ENODEV; + + ret = isci_port_perform_hard_reset(ihost, port->lldd_port, iphy); + + break; + case PHY_FUNC_GET_EVENTS: { + struct scu_link_layer_registers __iomem *r; + struct sas_phy *phy = sas_phy->phy; + + r = iphy->link_layer_registers; + phy->running_disparity_error_count = readl(&r->running_disparity_error_count); + phy->loss_of_dword_sync_count = readl(&r->loss_of_sync_error_count); + phy->phy_reset_problem_count = readl(&r->phy_reset_problem_count); + phy->invalid_dword_count = readl(&r->invalid_dword_counter); + break; + } + + default: + dev_dbg(&ihost->pdev->dev, + "%s: phy %p; func %d NOT IMPLEMENTED!\n", + __func__, sas_phy, func); + ret = -ENOSYS; + break; + } + return ret; +} |