diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/spi/spi-pic32-sqi.c | 715 |
1 files changed, 715 insertions, 0 deletions
diff --git a/drivers/spi/spi-pic32-sqi.c b/drivers/spi/spi-pic32-sqi.c new file mode 100644 index 000000000..86ad17597 --- /dev/null +++ b/drivers/spi/spi-pic32-sqi.c @@ -0,0 +1,715 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * PIC32 Quad SPI controller driver. + * + * Purna Chandra Mandal <purna.mandal@microchip.com> + * Copyright (c) 2016, Microchip Technology Inc. + */ + +#include <linux/clk.h> +#include <linux/dma-mapping.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/iopoll.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include <linux/spi/spi.h> + +/* SQI registers */ +#define PESQI_XIP_CONF1_REG 0x00 +#define PESQI_XIP_CONF2_REG 0x04 +#define PESQI_CONF_REG 0x08 +#define PESQI_CTRL_REG 0x0C +#define PESQI_CLK_CTRL_REG 0x10 +#define PESQI_CMD_THRES_REG 0x14 +#define PESQI_INT_THRES_REG 0x18 +#define PESQI_INT_ENABLE_REG 0x1C +#define PESQI_INT_STAT_REG 0x20 +#define PESQI_TX_DATA_REG 0x24 +#define PESQI_RX_DATA_REG 0x28 +#define PESQI_STAT1_REG 0x2C +#define PESQI_STAT2_REG 0x30 +#define PESQI_BD_CTRL_REG 0x34 +#define PESQI_BD_CUR_ADDR_REG 0x38 +#define PESQI_BD_BASE_ADDR_REG 0x40 +#define PESQI_BD_STAT_REG 0x44 +#define PESQI_BD_POLL_CTRL_REG 0x48 +#define PESQI_BD_TX_DMA_STAT_REG 0x4C +#define PESQI_BD_RX_DMA_STAT_REG 0x50 +#define PESQI_THRES_REG 0x54 +#define PESQI_INT_SIGEN_REG 0x58 + +/* PESQI_CONF_REG fields */ +#define PESQI_MODE 0x7 +#define PESQI_MODE_BOOT 0 +#define PESQI_MODE_PIO 1 +#define PESQI_MODE_DMA 2 +#define PESQI_MODE_XIP 3 +#define PESQI_MODE_SHIFT 0 +#define PESQI_CPHA BIT(3) +#define PESQI_CPOL BIT(4) +#define PESQI_LSBF BIT(5) +#define PESQI_RXLATCH BIT(7) +#define PESQI_SERMODE BIT(8) +#define PESQI_WP_EN BIT(9) +#define PESQI_HOLD_EN BIT(10) +#define PESQI_BURST_EN BIT(12) +#define PESQI_CS_CTRL_HW BIT(15) +#define PESQI_SOFT_RESET BIT(16) +#define PESQI_LANES_SHIFT 20 +#define PESQI_SINGLE_LANE 0 +#define PESQI_DUAL_LANE 1 +#define PESQI_QUAD_LANE 2 +#define PESQI_CSEN_SHIFT 24 +#define PESQI_EN BIT(23) + +/* PESQI_CLK_CTRL_REG fields */ +#define PESQI_CLK_EN BIT(0) +#define PESQI_CLK_STABLE BIT(1) +#define PESQI_CLKDIV_SHIFT 8 +#define PESQI_CLKDIV 0xff + +/* PESQI_INT_THR/CMD_THR_REG */ +#define PESQI_TXTHR_MASK 0x1f +#define PESQI_TXTHR_SHIFT 8 +#define PESQI_RXTHR_MASK 0x1f +#define PESQI_RXTHR_SHIFT 0 + +/* PESQI_INT_EN/INT_STAT/INT_SIG_EN_REG */ +#define PESQI_TXEMPTY BIT(0) +#define PESQI_TXFULL BIT(1) +#define PESQI_TXTHR BIT(2) +#define PESQI_RXEMPTY BIT(3) +#define PESQI_RXFULL BIT(4) +#define PESQI_RXTHR BIT(5) +#define PESQI_BDDONE BIT(9) /* BD processing complete */ +#define PESQI_PKTCOMP BIT(10) /* packet processing complete */ +#define PESQI_DMAERR BIT(11) /* error */ + +/* PESQI_BD_CTRL_REG */ +#define PESQI_DMA_EN BIT(0) /* enable DMA engine */ +#define PESQI_POLL_EN BIT(1) /* enable polling */ +#define PESQI_BDP_START BIT(2) /* start BD processor */ + +/* PESQI controller buffer descriptor */ +struct buf_desc { + u32 bd_ctrl; /* control */ + u32 bd_status; /* reserved */ + u32 bd_addr; /* DMA buffer addr */ + u32 bd_nextp; /* next item in chain */ +}; + +/* bd_ctrl */ +#define BD_BUFLEN 0x1ff +#define BD_CBD_INT_EN BIT(16) /* Current BD is processed */ +#define BD_PKT_INT_EN BIT(17) /* All BDs of PKT processed */ +#define BD_LIFM BIT(18) /* last data of pkt */ +#define BD_LAST BIT(19) /* end of list */ +#define BD_DATA_RECV BIT(20) /* receive data */ +#define BD_DDR BIT(21) /* DDR mode */ +#define BD_DUAL BIT(22) /* Dual SPI */ +#define BD_QUAD BIT(23) /* Quad SPI */ +#define BD_LSBF BIT(25) /* LSB First */ +#define BD_STAT_CHECK BIT(27) /* Status poll */ +#define BD_DEVSEL_SHIFT 28 /* CS */ +#define BD_CS_DEASSERT BIT(30) /* de-assert CS after current BD */ +#define BD_EN BIT(31) /* BD owned by H/W */ + +/** + * struct ring_desc - Representation of SQI ring descriptor + * @list: list element to add to free or used list. + * @bd: PESQI controller buffer descriptor + * @bd_dma: DMA address of PESQI controller buffer descriptor + * @xfer_len: transfer length + */ +struct ring_desc { + struct list_head list; + struct buf_desc *bd; + dma_addr_t bd_dma; + u32 xfer_len; +}; + +/* Global constants */ +#define PESQI_BD_BUF_LEN_MAX 256 +#define PESQI_BD_COUNT 256 /* max 64KB data per spi message */ + +struct pic32_sqi { + void __iomem *regs; + struct clk *sys_clk; + struct clk *base_clk; /* drives spi clock */ + struct spi_master *master; + int irq; + struct completion xfer_done; + struct ring_desc *ring; + void *bd; + dma_addr_t bd_dma; + struct list_head bd_list_free; /* free */ + struct list_head bd_list_used; /* allocated */ + struct spi_device *cur_spi; + u32 cur_speed; + u8 cur_mode; +}; + +static inline void pic32_setbits(void __iomem *reg, u32 set) +{ + writel(readl(reg) | set, reg); +} + +static inline void pic32_clrbits(void __iomem *reg, u32 clr) +{ + writel(readl(reg) & ~clr, reg); +} + +static int pic32_sqi_set_clk_rate(struct pic32_sqi *sqi, u32 sck) +{ + u32 val, div; + + /* div = base_clk / (2 * spi_clk) */ + div = clk_get_rate(sqi->base_clk) / (2 * sck); + div &= PESQI_CLKDIV; + + val = readl(sqi->regs + PESQI_CLK_CTRL_REG); + /* apply new divider */ + val &= ~(PESQI_CLK_STABLE | (PESQI_CLKDIV << PESQI_CLKDIV_SHIFT)); + val |= div << PESQI_CLKDIV_SHIFT; + writel(val, sqi->regs + PESQI_CLK_CTRL_REG); + + /* wait for stability */ + return readl_poll_timeout(sqi->regs + PESQI_CLK_CTRL_REG, val, + val & PESQI_CLK_STABLE, 1, 5000); +} + +static inline void pic32_sqi_enable_int(struct pic32_sqi *sqi) +{ + u32 mask = PESQI_DMAERR | PESQI_BDDONE | PESQI_PKTCOMP; + + writel(mask, sqi->regs + PESQI_INT_ENABLE_REG); + /* INT_SIGEN works as interrupt-gate to INTR line */ + writel(mask, sqi->regs + PESQI_INT_SIGEN_REG); +} + +static inline void pic32_sqi_disable_int(struct pic32_sqi *sqi) +{ + writel(0, sqi->regs + PESQI_INT_ENABLE_REG); + writel(0, sqi->regs + PESQI_INT_SIGEN_REG); +} + +static irqreturn_t pic32_sqi_isr(int irq, void *dev_id) +{ + struct pic32_sqi *sqi = dev_id; + u32 enable, status; + + enable = readl(sqi->regs + PESQI_INT_ENABLE_REG); + status = readl(sqi->regs + PESQI_INT_STAT_REG); + + /* check spurious interrupt */ + if (!status) + return IRQ_NONE; + + if (status & PESQI_DMAERR) { + enable = 0; + goto irq_done; + } + + if (status & PESQI_TXTHR) + enable &= ~(PESQI_TXTHR | PESQI_TXFULL | PESQI_TXEMPTY); + + if (status & PESQI_RXTHR) + enable &= ~(PESQI_RXTHR | PESQI_RXFULL | PESQI_RXEMPTY); + + if (status & PESQI_BDDONE) + enable &= ~PESQI_BDDONE; + + /* packet processing completed */ + if (status & PESQI_PKTCOMP) { + /* mask all interrupts */ + enable = 0; + /* complete trasaction */ + complete(&sqi->xfer_done); + } + +irq_done: + /* interrupts are sticky, so mask when handled */ + writel(enable, sqi->regs + PESQI_INT_ENABLE_REG); + + return IRQ_HANDLED; +} + +static struct ring_desc *ring_desc_get(struct pic32_sqi *sqi) +{ + struct ring_desc *rdesc; + + if (list_empty(&sqi->bd_list_free)) + return NULL; + + rdesc = list_first_entry(&sqi->bd_list_free, struct ring_desc, list); + list_move_tail(&rdesc->list, &sqi->bd_list_used); + return rdesc; +} + +static void ring_desc_put(struct pic32_sqi *sqi, struct ring_desc *rdesc) +{ + list_move(&rdesc->list, &sqi->bd_list_free); +} + +static int pic32_sqi_one_transfer(struct pic32_sqi *sqi, + struct spi_message *mesg, + struct spi_transfer *xfer) +{ + struct spi_device *spi = mesg->spi; + struct scatterlist *sg, *sgl; + struct ring_desc *rdesc; + struct buf_desc *bd; + int nents, i; + u32 bd_ctrl; + u32 nbits; + + /* Device selection */ + bd_ctrl = spi->chip_select << BD_DEVSEL_SHIFT; + + /* half-duplex: select transfer buffer, direction and lane */ + if (xfer->rx_buf) { + bd_ctrl |= BD_DATA_RECV; + nbits = xfer->rx_nbits; + sgl = xfer->rx_sg.sgl; + nents = xfer->rx_sg.nents; + } else { + nbits = xfer->tx_nbits; + sgl = xfer->tx_sg.sgl; + nents = xfer->tx_sg.nents; + } + + if (nbits & SPI_NBITS_QUAD) + bd_ctrl |= BD_QUAD; + else if (nbits & SPI_NBITS_DUAL) + bd_ctrl |= BD_DUAL; + + /* LSB first */ + if (spi->mode & SPI_LSB_FIRST) + bd_ctrl |= BD_LSBF; + + /* ownership to hardware */ + bd_ctrl |= BD_EN; + + for_each_sg(sgl, sg, nents, i) { + /* get ring descriptor */ + rdesc = ring_desc_get(sqi); + if (!rdesc) + break; + + bd = rdesc->bd; + + /* BD CTRL: length */ + rdesc->xfer_len = sg_dma_len(sg); + bd->bd_ctrl = bd_ctrl; + bd->bd_ctrl |= rdesc->xfer_len; + + /* BD STAT */ + bd->bd_status = 0; + + /* BD BUFFER ADDRESS */ + bd->bd_addr = sg->dma_address; + } + + return 0; +} + +static int pic32_sqi_prepare_hardware(struct spi_master *master) +{ + struct pic32_sqi *sqi = spi_master_get_devdata(master); + + /* enable spi interface */ + pic32_setbits(sqi->regs + PESQI_CONF_REG, PESQI_EN); + /* enable spi clk */ + pic32_setbits(sqi->regs + PESQI_CLK_CTRL_REG, PESQI_CLK_EN); + + return 0; +} + +static bool pic32_sqi_can_dma(struct spi_master *master, + struct spi_device *spi, + struct spi_transfer *x) +{ + /* Do DMA irrespective of transfer size */ + return true; +} + +static int pic32_sqi_one_message(struct spi_master *master, + struct spi_message *msg) +{ + struct spi_device *spi = msg->spi; + struct ring_desc *rdesc, *next; + struct spi_transfer *xfer; + struct pic32_sqi *sqi; + int ret = 0, mode; + unsigned long timeout; + u32 val; + + sqi = spi_master_get_devdata(master); + + reinit_completion(&sqi->xfer_done); + msg->actual_length = 0; + + /* We can't handle spi_transfer specific "speed_hz", "bits_per_word" + * and "delay_usecs". But spi_device specific speed and mode change + * can be handled at best during spi chip-select switch. + */ + if (sqi->cur_spi != spi) { + /* set spi speed */ + if (sqi->cur_speed != spi->max_speed_hz) { + sqi->cur_speed = spi->max_speed_hz; + ret = pic32_sqi_set_clk_rate(sqi, spi->max_speed_hz); + if (ret) + dev_warn(&spi->dev, "set_clk, %d\n", ret); + } + + /* set spi mode */ + mode = spi->mode & (SPI_MODE_3 | SPI_LSB_FIRST); + if (sqi->cur_mode != mode) { + val = readl(sqi->regs + PESQI_CONF_REG); + val &= ~(PESQI_CPOL | PESQI_CPHA | PESQI_LSBF); + if (mode & SPI_CPOL) + val |= PESQI_CPOL; + if (mode & SPI_LSB_FIRST) + val |= PESQI_LSBF; + val |= PESQI_CPHA; + writel(val, sqi->regs + PESQI_CONF_REG); + + sqi->cur_mode = mode; + } + sqi->cur_spi = spi; + } + + /* prepare hardware desc-list(BD) for transfer(s) */ + list_for_each_entry(xfer, &msg->transfers, transfer_list) { + ret = pic32_sqi_one_transfer(sqi, msg, xfer); + if (ret) { + dev_err(&spi->dev, "xfer %p err\n", xfer); + goto xfer_out; + } + } + + /* BDs are prepared and chained. Now mark LAST_BD, CS_DEASSERT at last + * element of the list. + */ + rdesc = list_last_entry(&sqi->bd_list_used, struct ring_desc, list); + rdesc->bd->bd_ctrl |= BD_LAST | BD_CS_DEASSERT | + BD_LIFM | BD_PKT_INT_EN; + + /* set base address BD list for DMA engine */ + rdesc = list_first_entry(&sqi->bd_list_used, struct ring_desc, list); + writel(rdesc->bd_dma, sqi->regs + PESQI_BD_BASE_ADDR_REG); + + /* enable interrupt */ + pic32_sqi_enable_int(sqi); + + /* enable DMA engine */ + val = PESQI_DMA_EN | PESQI_POLL_EN | PESQI_BDP_START; + writel(val, sqi->regs + PESQI_BD_CTRL_REG); + + /* wait for xfer completion */ + timeout = wait_for_completion_timeout(&sqi->xfer_done, 5 * HZ); + if (timeout == 0) { + dev_err(&sqi->master->dev, "wait timedout/interrupted\n"); + ret = -ETIMEDOUT; + msg->status = ret; + } else { + /* success */ + msg->status = 0; + ret = 0; + } + + /* disable DMA */ + writel(0, sqi->regs + PESQI_BD_CTRL_REG); + + pic32_sqi_disable_int(sqi); + +xfer_out: + list_for_each_entry_safe_reverse(rdesc, next, + &sqi->bd_list_used, list) { + /* Update total byte transferred */ + msg->actual_length += rdesc->xfer_len; + /* release ring descr */ + ring_desc_put(sqi, rdesc); + } + spi_finalize_current_message(spi->master); + + return ret; +} + +static int pic32_sqi_unprepare_hardware(struct spi_master *master) +{ + struct pic32_sqi *sqi = spi_master_get_devdata(master); + + /* disable clk */ + pic32_clrbits(sqi->regs + PESQI_CLK_CTRL_REG, PESQI_CLK_EN); + /* disable spi */ + pic32_clrbits(sqi->regs + PESQI_CONF_REG, PESQI_EN); + + return 0; +} + +static int ring_desc_ring_alloc(struct pic32_sqi *sqi) +{ + struct ring_desc *rdesc; + struct buf_desc *bd; + int i; + + /* allocate coherent DMAable memory for hardware buffer descriptors. */ + sqi->bd = dma_alloc_coherent(&sqi->master->dev, + sizeof(*bd) * PESQI_BD_COUNT, + &sqi->bd_dma, GFP_KERNEL); + if (!sqi->bd) { + dev_err(&sqi->master->dev, "failed allocating dma buffer\n"); + return -ENOMEM; + } + + /* allocate software ring descriptors */ + sqi->ring = kcalloc(PESQI_BD_COUNT, sizeof(*rdesc), GFP_KERNEL); + if (!sqi->ring) { + dma_free_coherent(&sqi->master->dev, + sizeof(*bd) * PESQI_BD_COUNT, + sqi->bd, sqi->bd_dma); + return -ENOMEM; + } + + bd = (struct buf_desc *)sqi->bd; + + INIT_LIST_HEAD(&sqi->bd_list_free); + INIT_LIST_HEAD(&sqi->bd_list_used); + + /* initialize ring-desc */ + for (i = 0, rdesc = sqi->ring; i < PESQI_BD_COUNT; i++, rdesc++) { + INIT_LIST_HEAD(&rdesc->list); + rdesc->bd = &bd[i]; + rdesc->bd_dma = sqi->bd_dma + (void *)&bd[i] - (void *)bd; + list_add_tail(&rdesc->list, &sqi->bd_list_free); + } + + /* Prepare BD: chain to next BD(s) */ + for (i = 0, rdesc = sqi->ring; i < PESQI_BD_COUNT - 1; i++) + bd[i].bd_nextp = rdesc[i + 1].bd_dma; + bd[PESQI_BD_COUNT - 1].bd_nextp = 0; + + return 0; +} + +static void ring_desc_ring_free(struct pic32_sqi *sqi) +{ + dma_free_coherent(&sqi->master->dev, + sizeof(struct buf_desc) * PESQI_BD_COUNT, + sqi->bd, sqi->bd_dma); + kfree(sqi->ring); +} + +static void pic32_sqi_hw_init(struct pic32_sqi *sqi) +{ + unsigned long flags; + u32 val; + + /* Soft-reset of PESQI controller triggers interrupt. + * We are not yet ready to handle them so disable CPU + * interrupt for the time being. + */ + local_irq_save(flags); + + /* assert soft-reset */ + writel(PESQI_SOFT_RESET, sqi->regs + PESQI_CONF_REG); + + /* wait until clear */ + readl_poll_timeout_atomic(sqi->regs + PESQI_CONF_REG, val, + !(val & PESQI_SOFT_RESET), 1, 5000); + + /* disable all interrupts */ + pic32_sqi_disable_int(sqi); + + /* Now it is safe to enable back CPU interrupt */ + local_irq_restore(flags); + + /* tx and rx fifo interrupt threshold */ + val = readl(sqi->regs + PESQI_CMD_THRES_REG); + val &= ~(PESQI_TXTHR_MASK << PESQI_TXTHR_SHIFT); + val &= ~(PESQI_RXTHR_MASK << PESQI_RXTHR_SHIFT); + val |= (1U << PESQI_TXTHR_SHIFT) | (1U << PESQI_RXTHR_SHIFT); + writel(val, sqi->regs + PESQI_CMD_THRES_REG); + + val = readl(sqi->regs + PESQI_INT_THRES_REG); + val &= ~(PESQI_TXTHR_MASK << PESQI_TXTHR_SHIFT); + val &= ~(PESQI_RXTHR_MASK << PESQI_RXTHR_SHIFT); + val |= (1U << PESQI_TXTHR_SHIFT) | (1U << PESQI_RXTHR_SHIFT); + writel(val, sqi->regs + PESQI_INT_THRES_REG); + + /* default configuration */ + val = readl(sqi->regs + PESQI_CONF_REG); + + /* set mode: DMA */ + val &= ~PESQI_MODE; + val |= PESQI_MODE_DMA << PESQI_MODE_SHIFT; + writel(val, sqi->regs + PESQI_CONF_REG); + + /* DATAEN - SQIID0-ID3 */ + val |= PESQI_QUAD_LANE << PESQI_LANES_SHIFT; + + /* burst/INCR4 enable */ + val |= PESQI_BURST_EN; + + /* CSEN - all CS */ + val |= 3U << PESQI_CSEN_SHIFT; + writel(val, sqi->regs + PESQI_CONF_REG); + + /* write poll count */ + writel(0, sqi->regs + PESQI_BD_POLL_CTRL_REG); + + sqi->cur_speed = 0; + sqi->cur_mode = -1; +} + +static int pic32_sqi_probe(struct platform_device *pdev) +{ + struct spi_master *master; + struct pic32_sqi *sqi; + int ret; + + master = spi_alloc_master(&pdev->dev, sizeof(*sqi)); + if (!master) + return -ENOMEM; + + sqi = spi_master_get_devdata(master); + sqi->master = master; + + sqi->regs = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(sqi->regs)) { + ret = PTR_ERR(sqi->regs); + goto err_free_master; + } + + /* irq */ + sqi->irq = platform_get_irq(pdev, 0); + if (sqi->irq < 0) { + ret = sqi->irq; + goto err_free_master; + } + + /* clocks */ + sqi->sys_clk = devm_clk_get(&pdev->dev, "reg_ck"); + if (IS_ERR(sqi->sys_clk)) { + ret = PTR_ERR(sqi->sys_clk); + dev_err(&pdev->dev, "no sys_clk ?\n"); + goto err_free_master; + } + + sqi->base_clk = devm_clk_get(&pdev->dev, "spi_ck"); + if (IS_ERR(sqi->base_clk)) { + ret = PTR_ERR(sqi->base_clk); + dev_err(&pdev->dev, "no base clk ?\n"); + goto err_free_master; + } + + ret = clk_prepare_enable(sqi->sys_clk); + if (ret) { + dev_err(&pdev->dev, "sys clk enable failed\n"); + goto err_free_master; + } + + ret = clk_prepare_enable(sqi->base_clk); + if (ret) { + dev_err(&pdev->dev, "base clk enable failed\n"); + clk_disable_unprepare(sqi->sys_clk); + goto err_free_master; + } + + init_completion(&sqi->xfer_done); + + /* initialize hardware */ + pic32_sqi_hw_init(sqi); + + /* allocate buffers & descriptors */ + ret = ring_desc_ring_alloc(sqi); + if (ret) { + dev_err(&pdev->dev, "ring alloc failed\n"); + goto err_disable_clk; + } + + /* install irq handlers */ + ret = request_irq(sqi->irq, pic32_sqi_isr, 0, + dev_name(&pdev->dev), sqi); + if (ret < 0) { + dev_err(&pdev->dev, "request_irq(%d), failed\n", sqi->irq); + goto err_free_ring; + } + + /* register master */ + master->num_chipselect = 2; + master->max_speed_hz = clk_get_rate(sqi->base_clk); + master->dma_alignment = 32; + master->max_dma_len = PESQI_BD_BUF_LEN_MAX; + master->dev.of_node = pdev->dev.of_node; + master->mode_bits = SPI_MODE_3 | SPI_MODE_0 | SPI_TX_DUAL | + SPI_RX_DUAL | SPI_TX_QUAD | SPI_RX_QUAD; + master->flags = SPI_MASTER_HALF_DUPLEX; + master->can_dma = pic32_sqi_can_dma; + master->bits_per_word_mask = SPI_BPW_RANGE_MASK(8, 32); + master->transfer_one_message = pic32_sqi_one_message; + master->prepare_transfer_hardware = pic32_sqi_prepare_hardware; + master->unprepare_transfer_hardware = pic32_sqi_unprepare_hardware; + + ret = devm_spi_register_master(&pdev->dev, master); + if (ret) { + dev_err(&master->dev, "failed registering spi master\n"); + free_irq(sqi->irq, sqi); + goto err_free_ring; + } + + platform_set_drvdata(pdev, sqi); + + return 0; + +err_free_ring: + ring_desc_ring_free(sqi); + +err_disable_clk: + clk_disable_unprepare(sqi->base_clk); + clk_disable_unprepare(sqi->sys_clk); + +err_free_master: + spi_master_put(master); + return ret; +} + +static int pic32_sqi_remove(struct platform_device *pdev) +{ + struct pic32_sqi *sqi = platform_get_drvdata(pdev); + + /* release resources */ + free_irq(sqi->irq, sqi); + ring_desc_ring_free(sqi); + + /* disable clk */ + clk_disable_unprepare(sqi->base_clk); + clk_disable_unprepare(sqi->sys_clk); + + return 0; +} + +static const struct of_device_id pic32_sqi_of_ids[] = { + {.compatible = "microchip,pic32mzda-sqi",}, + {}, +}; +MODULE_DEVICE_TABLE(of, pic32_sqi_of_ids); + +static struct platform_driver pic32_sqi_driver = { + .driver = { + .name = "sqi-pic32", + .of_match_table = of_match_ptr(pic32_sqi_of_ids), + }, + .probe = pic32_sqi_probe, + .remove = pic32_sqi_remove, +}; + +module_platform_driver(pic32_sqi_driver); + +MODULE_AUTHOR("Purna Chandra Mandal <purna.mandal@microchip.com>"); +MODULE_DESCRIPTION("Microchip SPI driver for PIC32 SQI controller."); +MODULE_LICENSE("GPL v2"); |