diff options
Diffstat (limited to '')
-rw-r--r-- | drivers/usb/gadget/udc/fsl_usb2_udc.h | 591 |
1 files changed, 591 insertions, 0 deletions
diff --git a/drivers/usb/gadget/udc/fsl_usb2_udc.h b/drivers/usb/gadget/udc/fsl_usb2_udc.h new file mode 100644 index 000000000..2efc5a930 --- /dev/null +++ b/drivers/usb/gadget/udc/fsl_usb2_udc.h @@ -0,0 +1,591 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Copyright (C) 2004,2012 Freescale Semiconductor, Inc + * All rights reserved. + * + * Freescale USB device/endpoint management registers + */ +#ifndef __FSL_USB2_UDC_H +#define __FSL_USB2_UDC_H + +#include <linux/usb/ch9.h> +#include <linux/usb/gadget.h> + +/* ### define USB registers here + */ +#define USB_MAX_CTRL_PAYLOAD 64 +#define USB_DR_SYS_OFFSET 0x400 + + /* USB DR device mode registers (Little Endian) */ +struct usb_dr_device { + /* Capability register */ + u8 res1[256]; + u16 caplength; /* Capability Register Length */ + u16 hciversion; /* Host Controller Interface Version */ + u32 hcsparams; /* Host Controller Structural Parameters */ + u32 hccparams; /* Host Controller Capability Parameters */ + u8 res2[20]; + u32 dciversion; /* Device Controller Interface Version */ + u32 dccparams; /* Device Controller Capability Parameters */ + u8 res3[24]; + /* Operation register */ + u32 usbcmd; /* USB Command Register */ + u32 usbsts; /* USB Status Register */ + u32 usbintr; /* USB Interrupt Enable Register */ + u32 frindex; /* Frame Index Register */ + u8 res4[4]; + u32 deviceaddr; /* Device Address */ + u32 endpointlistaddr; /* Endpoint List Address Register */ + u8 res5[4]; + u32 burstsize; /* Master Interface Data Burst Size Register */ + u32 txttfilltuning; /* Transmit FIFO Tuning Controls Register */ + u8 res6[24]; + u32 configflag; /* Configure Flag Register */ + u32 portsc1; /* Port 1 Status and Control Register */ + u8 res7[28]; + u32 otgsc; /* On-The-Go Status and Control */ + u32 usbmode; /* USB Mode Register */ + u32 endptsetupstat; /* Endpoint Setup Status Register */ + u32 endpointprime; /* Endpoint Initialization Register */ + u32 endptflush; /* Endpoint Flush Register */ + u32 endptstatus; /* Endpoint Status Register */ + u32 endptcomplete; /* Endpoint Complete Register */ + u32 endptctrl[6]; /* Endpoint Control Registers */ +}; + + /* USB DR host mode registers (Little Endian) */ +struct usb_dr_host { + /* Capability register */ + u8 res1[256]; + u16 caplength; /* Capability Register Length */ + u16 hciversion; /* Host Controller Interface Version */ + u32 hcsparams; /* Host Controller Structural Parameters */ + u32 hccparams; /* Host Controller Capability Parameters */ + u8 res2[20]; + u32 dciversion; /* Device Controller Interface Version */ + u32 dccparams; /* Device Controller Capability Parameters */ + u8 res3[24]; + /* Operation register */ + u32 usbcmd; /* USB Command Register */ + u32 usbsts; /* USB Status Register */ + u32 usbintr; /* USB Interrupt Enable Register */ + u32 frindex; /* Frame Index Register */ + u8 res4[4]; + u32 periodiclistbase; /* Periodic Frame List Base Address Register */ + u32 asynclistaddr; /* Current Asynchronous List Address Register */ + u8 res5[4]; + u32 burstsize; /* Master Interface Data Burst Size Register */ + u32 txttfilltuning; /* Transmit FIFO Tuning Controls Register */ + u8 res6[24]; + u32 configflag; /* Configure Flag Register */ + u32 portsc1; /* Port 1 Status and Control Register */ + u8 res7[28]; + u32 otgsc; /* On-The-Go Status and Control */ + u32 usbmode; /* USB Mode Register */ + u32 endptsetupstat; /* Endpoint Setup Status Register */ + u32 endpointprime; /* Endpoint Initialization Register */ + u32 endptflush; /* Endpoint Flush Register */ + u32 endptstatus; /* Endpoint Status Register */ + u32 endptcomplete; /* Endpoint Complete Register */ + u32 endptctrl[6]; /* Endpoint Control Registers */ +}; + + /* non-EHCI USB system interface registers (Big Endian) */ +struct usb_sys_interface { + u32 snoop1; + u32 snoop2; + u32 age_cnt_thresh; /* Age Count Threshold Register */ + u32 pri_ctrl; /* Priority Control Register */ + u32 si_ctrl; /* System Interface Control Register */ + u8 res[236]; + u32 control; /* General Purpose Control Register */ +}; + +/* ep0 transfer state */ +#define WAIT_FOR_SETUP 0 +#define DATA_STATE_XMIT 1 +#define DATA_STATE_NEED_ZLP 2 +#define WAIT_FOR_OUT_STATUS 3 +#define DATA_STATE_RECV 4 + +/* Device Controller Capability Parameter register */ +#define DCCPARAMS_DC 0x00000080 +#define DCCPARAMS_DEN_MASK 0x0000001f + +/* Frame Index Register Bit Masks */ +#define USB_FRINDEX_MASKS 0x3fff +/* USB CMD Register Bit Masks */ +#define USB_CMD_RUN_STOP 0x00000001 +#define USB_CMD_CTRL_RESET 0x00000002 +#define USB_CMD_PERIODIC_SCHEDULE_EN 0x00000010 +#define USB_CMD_ASYNC_SCHEDULE_EN 0x00000020 +#define USB_CMD_INT_AA_DOORBELL 0x00000040 +#define USB_CMD_ASP 0x00000300 +#define USB_CMD_ASYNC_SCH_PARK_EN 0x00000800 +#define USB_CMD_SUTW 0x00002000 +#define USB_CMD_ATDTW 0x00004000 +#define USB_CMD_ITC 0x00FF0000 + +/* bit 15,3,2 are frame list size */ +#define USB_CMD_FRAME_SIZE_1024 0x00000000 +#define USB_CMD_FRAME_SIZE_512 0x00000004 +#define USB_CMD_FRAME_SIZE_256 0x00000008 +#define USB_CMD_FRAME_SIZE_128 0x0000000C +#define USB_CMD_FRAME_SIZE_64 0x00008000 +#define USB_CMD_FRAME_SIZE_32 0x00008004 +#define USB_CMD_FRAME_SIZE_16 0x00008008 +#define USB_CMD_FRAME_SIZE_8 0x0000800C + +/* bit 9-8 are async schedule park mode count */ +#define USB_CMD_ASP_00 0x00000000 +#define USB_CMD_ASP_01 0x00000100 +#define USB_CMD_ASP_10 0x00000200 +#define USB_CMD_ASP_11 0x00000300 +#define USB_CMD_ASP_BIT_POS 8 + +/* bit 23-16 are interrupt threshold control */ +#define USB_CMD_ITC_NO_THRESHOLD 0x00000000 +#define USB_CMD_ITC_1_MICRO_FRM 0x00010000 +#define USB_CMD_ITC_2_MICRO_FRM 0x00020000 +#define USB_CMD_ITC_4_MICRO_FRM 0x00040000 +#define USB_CMD_ITC_8_MICRO_FRM 0x00080000 +#define USB_CMD_ITC_16_MICRO_FRM 0x00100000 +#define USB_CMD_ITC_32_MICRO_FRM 0x00200000 +#define USB_CMD_ITC_64_MICRO_FRM 0x00400000 +#define USB_CMD_ITC_BIT_POS 16 + +/* USB STS Register Bit Masks */ +#define USB_STS_INT 0x00000001 +#define USB_STS_ERR 0x00000002 +#define USB_STS_PORT_CHANGE 0x00000004 +#define USB_STS_FRM_LST_ROLL 0x00000008 +#define USB_STS_SYS_ERR 0x00000010 +#define USB_STS_IAA 0x00000020 +#define USB_STS_RESET 0x00000040 +#define USB_STS_SOF 0x00000080 +#define USB_STS_SUSPEND 0x00000100 +#define USB_STS_HC_HALTED 0x00001000 +#define USB_STS_RCL 0x00002000 +#define USB_STS_PERIODIC_SCHEDULE 0x00004000 +#define USB_STS_ASYNC_SCHEDULE 0x00008000 + +/* USB INTR Register Bit Masks */ +#define USB_INTR_INT_EN 0x00000001 +#define USB_INTR_ERR_INT_EN 0x00000002 +#define USB_INTR_PTC_DETECT_EN 0x00000004 +#define USB_INTR_FRM_LST_ROLL_EN 0x00000008 +#define USB_INTR_SYS_ERR_EN 0x00000010 +#define USB_INTR_ASYN_ADV_EN 0x00000020 +#define USB_INTR_RESET_EN 0x00000040 +#define USB_INTR_SOF_EN 0x00000080 +#define USB_INTR_DEVICE_SUSPEND 0x00000100 + +/* Device Address bit masks */ +#define USB_DEVICE_ADDRESS_MASK 0xFE000000 +#define USB_DEVICE_ADDRESS_BIT_POS 25 + +/* endpoint list address bit masks */ +#define USB_EP_LIST_ADDRESS_MASK 0xfffff800 + +/* PORTSCX Register Bit Masks */ +#define PORTSCX_CURRENT_CONNECT_STATUS 0x00000001 +#define PORTSCX_CONNECT_STATUS_CHANGE 0x00000002 +#define PORTSCX_PORT_ENABLE 0x00000004 +#define PORTSCX_PORT_EN_DIS_CHANGE 0x00000008 +#define PORTSCX_OVER_CURRENT_ACT 0x00000010 +#define PORTSCX_OVER_CURRENT_CHG 0x00000020 +#define PORTSCX_PORT_FORCE_RESUME 0x00000040 +#define PORTSCX_PORT_SUSPEND 0x00000080 +#define PORTSCX_PORT_RESET 0x00000100 +#define PORTSCX_LINE_STATUS_BITS 0x00000C00 +#define PORTSCX_PORT_POWER 0x00001000 +#define PORTSCX_PORT_INDICTOR_CTRL 0x0000C000 +#define PORTSCX_PORT_TEST_CTRL 0x000F0000 +#define PORTSCX_WAKE_ON_CONNECT_EN 0x00100000 +#define PORTSCX_WAKE_ON_CONNECT_DIS 0x00200000 +#define PORTSCX_WAKE_ON_OVER_CURRENT 0x00400000 +#define PORTSCX_PHY_LOW_POWER_SPD 0x00800000 +#define PORTSCX_PORT_FORCE_FULL_SPEED 0x01000000 +#define PORTSCX_PORT_SPEED_MASK 0x0C000000 +#define PORTSCX_PORT_WIDTH 0x10000000 +#define PORTSCX_PHY_TYPE_SEL 0xC0000000 + +/* bit 11-10 are line status */ +#define PORTSCX_LINE_STATUS_SE0 0x00000000 +#define PORTSCX_LINE_STATUS_JSTATE 0x00000400 +#define PORTSCX_LINE_STATUS_KSTATE 0x00000800 +#define PORTSCX_LINE_STATUS_UNDEF 0x00000C00 +#define PORTSCX_LINE_STATUS_BIT_POS 10 + +/* bit 15-14 are port indicator control */ +#define PORTSCX_PIC_OFF 0x00000000 +#define PORTSCX_PIC_AMBER 0x00004000 +#define PORTSCX_PIC_GREEN 0x00008000 +#define PORTSCX_PIC_UNDEF 0x0000C000 +#define PORTSCX_PIC_BIT_POS 14 + +/* bit 19-16 are port test control */ +#define PORTSCX_PTC_DISABLE 0x00000000 +#define PORTSCX_PTC_JSTATE 0x00010000 +#define PORTSCX_PTC_KSTATE 0x00020000 +#define PORTSCX_PTC_SEQNAK 0x00030000 +#define PORTSCX_PTC_PACKET 0x00040000 +#define PORTSCX_PTC_FORCE_EN 0x00050000 +#define PORTSCX_PTC_BIT_POS 16 + +/* bit 27-26 are port speed */ +#define PORTSCX_PORT_SPEED_FULL 0x00000000 +#define PORTSCX_PORT_SPEED_LOW 0x04000000 +#define PORTSCX_PORT_SPEED_HIGH 0x08000000 +#define PORTSCX_PORT_SPEED_UNDEF 0x0C000000 +#define PORTSCX_SPEED_BIT_POS 26 + +/* bit 28 is parallel transceiver width for UTMI interface */ +#define PORTSCX_PTW 0x10000000 +#define PORTSCX_PTW_8BIT 0x00000000 +#define PORTSCX_PTW_16BIT 0x10000000 + +/* bit 31-30 are port transceiver select */ +#define PORTSCX_PTS_UTMI 0x00000000 +#define PORTSCX_PTS_ULPI 0x80000000 +#define PORTSCX_PTS_FSLS 0xC0000000 +#define PORTSCX_PTS_BIT_POS 30 + +/* otgsc Register Bit Masks */ +#define OTGSC_CTRL_VUSB_DISCHARGE 0x00000001 +#define OTGSC_CTRL_VUSB_CHARGE 0x00000002 +#define OTGSC_CTRL_OTG_TERM 0x00000008 +#define OTGSC_CTRL_DATA_PULSING 0x00000010 +#define OTGSC_STS_USB_ID 0x00000100 +#define OTGSC_STS_A_VBUS_VALID 0x00000200 +#define OTGSC_STS_A_SESSION_VALID 0x00000400 +#define OTGSC_STS_B_SESSION_VALID 0x00000800 +#define OTGSC_STS_B_SESSION_END 0x00001000 +#define OTGSC_STS_1MS_TOGGLE 0x00002000 +#define OTGSC_STS_DATA_PULSING 0x00004000 +#define OTGSC_INTSTS_USB_ID 0x00010000 +#define OTGSC_INTSTS_A_VBUS_VALID 0x00020000 +#define OTGSC_INTSTS_A_SESSION_VALID 0x00040000 +#define OTGSC_INTSTS_B_SESSION_VALID 0x00080000 +#define OTGSC_INTSTS_B_SESSION_END 0x00100000 +#define OTGSC_INTSTS_1MS 0x00200000 +#define OTGSC_INTSTS_DATA_PULSING 0x00400000 +#define OTGSC_INTR_USB_ID 0x01000000 +#define OTGSC_INTR_A_VBUS_VALID 0x02000000 +#define OTGSC_INTR_A_SESSION_VALID 0x04000000 +#define OTGSC_INTR_B_SESSION_VALID 0x08000000 +#define OTGSC_INTR_B_SESSION_END 0x10000000 +#define OTGSC_INTR_1MS_TIMER 0x20000000 +#define OTGSC_INTR_DATA_PULSING 0x40000000 + +/* USB MODE Register Bit Masks */ +#define USB_MODE_CTRL_MODE_IDLE 0x00000000 +#define USB_MODE_CTRL_MODE_DEVICE 0x00000002 +#define USB_MODE_CTRL_MODE_HOST 0x00000003 +#define USB_MODE_CTRL_MODE_MASK 0x00000003 +#define USB_MODE_CTRL_MODE_RSV 0x00000001 +#define USB_MODE_ES 0x00000004 /* Endian Select */ +#define USB_MODE_SETUP_LOCK_OFF 0x00000008 +#define USB_MODE_STREAM_DISABLE 0x00000010 +/* Endpoint Flush Register */ +#define EPFLUSH_TX_OFFSET 0x00010000 +#define EPFLUSH_RX_OFFSET 0x00000000 + +/* Endpoint Setup Status bit masks */ +#define EP_SETUP_STATUS_MASK 0x0000003F +#define EP_SETUP_STATUS_EP0 0x00000001 + +/* ENDPOINTCTRLx Register Bit Masks */ +#define EPCTRL_TX_ENABLE 0x00800000 +#define EPCTRL_TX_DATA_TOGGLE_RST 0x00400000 /* Not EP0 */ +#define EPCTRL_TX_DATA_TOGGLE_INH 0x00200000 /* Not EP0 */ +#define EPCTRL_TX_TYPE 0x000C0000 +#define EPCTRL_TX_DATA_SOURCE 0x00020000 /* Not EP0 */ +#define EPCTRL_TX_EP_STALL 0x00010000 +#define EPCTRL_RX_ENABLE 0x00000080 +#define EPCTRL_RX_DATA_TOGGLE_RST 0x00000040 /* Not EP0 */ +#define EPCTRL_RX_DATA_TOGGLE_INH 0x00000020 /* Not EP0 */ +#define EPCTRL_RX_TYPE 0x0000000C +#define EPCTRL_RX_DATA_SINK 0x00000002 /* Not EP0 */ +#define EPCTRL_RX_EP_STALL 0x00000001 + +/* bit 19-18 and 3-2 are endpoint type */ +#define EPCTRL_EP_TYPE_CONTROL 0 +#define EPCTRL_EP_TYPE_ISO 1 +#define EPCTRL_EP_TYPE_BULK 2 +#define EPCTRL_EP_TYPE_INTERRUPT 3 +#define EPCTRL_TX_EP_TYPE_SHIFT 18 +#define EPCTRL_RX_EP_TYPE_SHIFT 2 + +/* SNOOPn Register Bit Masks */ +#define SNOOP_ADDRESS_MASK 0xFFFFF000 +#define SNOOP_SIZE_ZERO 0x00 /* snooping disable */ +#define SNOOP_SIZE_4KB 0x0B /* 4KB snoop size */ +#define SNOOP_SIZE_8KB 0x0C +#define SNOOP_SIZE_16KB 0x0D +#define SNOOP_SIZE_32KB 0x0E +#define SNOOP_SIZE_64KB 0x0F +#define SNOOP_SIZE_128KB 0x10 +#define SNOOP_SIZE_256KB 0x11 +#define SNOOP_SIZE_512KB 0x12 +#define SNOOP_SIZE_1MB 0x13 +#define SNOOP_SIZE_2MB 0x14 +#define SNOOP_SIZE_4MB 0x15 +#define SNOOP_SIZE_8MB 0x16 +#define SNOOP_SIZE_16MB 0x17 +#define SNOOP_SIZE_32MB 0x18 +#define SNOOP_SIZE_64MB 0x19 +#define SNOOP_SIZE_128MB 0x1A +#define SNOOP_SIZE_256MB 0x1B +#define SNOOP_SIZE_512MB 0x1C +#define SNOOP_SIZE_1GB 0x1D +#define SNOOP_SIZE_2GB 0x1E /* 2GB snoop size */ + +/* pri_ctrl Register Bit Masks */ +#define PRI_CTRL_PRI_LVL1 0x0000000C +#define PRI_CTRL_PRI_LVL0 0x00000003 + +/* si_ctrl Register Bit Masks */ +#define SI_CTRL_ERR_DISABLE 0x00000010 +#define SI_CTRL_IDRC_DISABLE 0x00000008 +#define SI_CTRL_RD_SAFE_EN 0x00000004 +#define SI_CTRL_RD_PREFETCH_DISABLE 0x00000002 +#define SI_CTRL_RD_PREFEFETCH_VAL 0x00000001 + +/* control Register Bit Masks */ +#define USB_CTRL_IOENB 0x00000004 +#define USB_CTRL_ULPI_INT0EN 0x00000001 +#define USB_CTRL_UTMI_PHY_EN 0x00000200 +#define USB_CTRL_USB_EN 0x00000004 +#define USB_CTRL_ULPI_PHY_CLK_SEL 0x00000400 + +/* Endpoint Queue Head data struct + * Rem: all the variables of qh are LittleEndian Mode + * and NEXT_POINTER_MASK should operate on a LittleEndian, Phy Addr + */ +struct ep_queue_head { + u32 max_pkt_length; /* Mult(31-30) , Zlt(29) , Max Pkt len + and IOS(15) */ + u32 curr_dtd_ptr; /* Current dTD Pointer(31-5) */ + u32 next_dtd_ptr; /* Next dTD Pointer(31-5), T(0) */ + u32 size_ioc_int_sts; /* Total bytes (30-16), IOC (15), + MultO(11-10), STS (7-0) */ + u32 buff_ptr0; /* Buffer pointer Page 0 (31-12) */ + u32 buff_ptr1; /* Buffer pointer Page 1 (31-12) */ + u32 buff_ptr2; /* Buffer pointer Page 2 (31-12) */ + u32 buff_ptr3; /* Buffer pointer Page 3 (31-12) */ + u32 buff_ptr4; /* Buffer pointer Page 4 (31-12) */ + u32 res1; + u8 setup_buffer[8]; /* Setup data 8 bytes */ + u32 res2[4]; +}; + +/* Endpoint Queue Head Bit Masks */ +#define EP_QUEUE_HEAD_MULT_POS 30 +#define EP_QUEUE_HEAD_ZLT_SEL 0x20000000 +#define EP_QUEUE_HEAD_MAX_PKT_LEN_POS 16 +#define EP_QUEUE_HEAD_MAX_PKT_LEN(ep_info) (((ep_info)>>16)&0x07ff) +#define EP_QUEUE_HEAD_IOS 0x00008000 +#define EP_QUEUE_HEAD_NEXT_TERMINATE 0x00000001 +#define EP_QUEUE_HEAD_IOC 0x00008000 +#define EP_QUEUE_HEAD_MULTO 0x00000C00 +#define EP_QUEUE_HEAD_STATUS_HALT 0x00000040 +#define EP_QUEUE_HEAD_STATUS_ACTIVE 0x00000080 +#define EP_QUEUE_CURRENT_OFFSET_MASK 0x00000FFF +#define EP_QUEUE_HEAD_NEXT_POINTER_MASK 0xFFFFFFE0 +#define EP_QUEUE_FRINDEX_MASK 0x000007FF +#define EP_MAX_LENGTH_TRANSFER 0x4000 + +/* Endpoint Transfer Descriptor data struct */ +/* Rem: all the variables of td are LittleEndian Mode */ +struct ep_td_struct { + u32 next_td_ptr; /* Next TD pointer(31-5), T(0) set + indicate invalid */ + u32 size_ioc_sts; /* Total bytes (30-16), IOC (15), + MultO(11-10), STS (7-0) */ + u32 buff_ptr0; /* Buffer pointer Page 0 */ + u32 buff_ptr1; /* Buffer pointer Page 1 */ + u32 buff_ptr2; /* Buffer pointer Page 2 */ + u32 buff_ptr3; /* Buffer pointer Page 3 */ + u32 buff_ptr4; /* Buffer pointer Page 4 */ + u32 res; + /* 32 bytes */ + dma_addr_t td_dma; /* dma address for this td */ + /* virtual address of next td specified in next_td_ptr */ + struct ep_td_struct *next_td_virt; +}; + +/* Endpoint Transfer Descriptor bit Masks */ +#define DTD_NEXT_TERMINATE 0x00000001 +#define DTD_IOC 0x00008000 +#define DTD_STATUS_ACTIVE 0x00000080 +#define DTD_STATUS_HALTED 0x00000040 +#define DTD_STATUS_DATA_BUFF_ERR 0x00000020 +#define DTD_STATUS_TRANSACTION_ERR 0x00000008 +#define DTD_RESERVED_FIELDS 0x80007300 +#define DTD_ADDR_MASK 0xFFFFFFE0 +#define DTD_PACKET_SIZE 0x7FFF0000 +#define DTD_LENGTH_BIT_POS 16 +#define DTD_ERROR_MASK (DTD_STATUS_HALTED | \ + DTD_STATUS_DATA_BUFF_ERR | \ + DTD_STATUS_TRANSACTION_ERR) +/* Alignment requirements; must be a power of two */ +#define DTD_ALIGNMENT 0x20 +#define QH_ALIGNMENT 2048 + +/* Controller dma boundary */ +#define UDC_DMA_BOUNDARY 0x1000 + +/*-------------------------------------------------------------------------*/ + +/* ### driver private data + */ +struct fsl_req { + struct usb_request req; + struct list_head queue; + /* ep_queue() func will add + a request->queue into a udc_ep->queue 'd tail */ + struct fsl_ep *ep; + unsigned mapped:1; + + struct ep_td_struct *head, *tail; /* For dTD List + cpu endian Virtual addr */ + unsigned int dtd_count; +}; + +#define REQ_UNCOMPLETE 1 + +struct fsl_ep { + struct usb_ep ep; + struct list_head queue; + struct fsl_udc *udc; + struct ep_queue_head *qh; + struct usb_gadget *gadget; + + char name[14]; + unsigned stopped:1; +}; + +#define EP_DIR_IN 1 +#define EP_DIR_OUT 0 + +struct fsl_udc { + struct usb_gadget gadget; + struct usb_gadget_driver *driver; + struct fsl_usb2_platform_data *pdata; + struct completion *done; /* to make sure release() is done */ + struct fsl_ep *eps; + unsigned int max_ep; + unsigned int irq; + + struct usb_ctrlrequest local_setup_buff; + spinlock_t lock; + struct usb_phy *transceiver; + unsigned softconnect:1; + unsigned vbus_active:1; + unsigned stopped:1; + unsigned remote_wakeup:1; + unsigned already_stopped:1; + unsigned big_endian_desc:1; + + struct ep_queue_head *ep_qh; /* Endpoints Queue-Head */ + struct fsl_req *status_req; /* ep0 status request */ + struct dma_pool *td_pool; /* dma pool for DTD */ + enum fsl_usb2_phy_modes phy_mode; + + size_t ep_qh_size; /* size after alignment adjustment*/ + dma_addr_t ep_qh_dma; /* dma address of QH */ + + u32 max_pipes; /* Device max pipes */ + u32 bus_reset; /* Device is bus resetting */ + u32 resume_state; /* USB state to resume */ + u32 usb_state; /* USB current state */ + u32 ep0_state; /* Endpoint zero state */ + u32 ep0_dir; /* Endpoint zero direction: can be + USB_DIR_IN or USB_DIR_OUT */ + u8 device_address; /* Device USB address */ +}; + +/*-------------------------------------------------------------------------*/ + +#ifdef DEBUG +#define DBG(fmt, args...) printk(KERN_DEBUG "[%s] " fmt "\n", \ + __func__, ## args) +#else +#define DBG(fmt, args...) do{}while(0) +#endif + +#if 0 +static void dump_msg(const char *label, const u8 * buf, unsigned int length) +{ + unsigned int start, num, i; + char line[52], *p; + + if (length >= 512) + return; + DBG("%s, length %u:\n", label, length); + start = 0; + while (length > 0) { + num = min(length, 16u); + p = line; + for (i = 0; i < num; ++i) { + if (i == 8) + *p++ = ' '; + sprintf(p, " %02x", buf[i]); + p += 3; + } + *p = 0; + printk(KERN_DEBUG "%6x: %s\n", start, line); + buf += num; + start += num; + length -= num; + } +} +#endif + +#ifdef VERBOSE +#define VDBG DBG +#else +#define VDBG(stuff...) do{}while(0) +#endif + +#define ERR(stuff...) pr_err("udc: " stuff) +#define WARNING(stuff...) pr_warn("udc: " stuff) +#define INFO(stuff...) pr_info("udc: " stuff) + +/*-------------------------------------------------------------------------*/ + +/* ### Add board specific defines here + */ + +/* + * ### pipe direction macro from device view + */ +#define USB_RECV 0 /* OUT EP */ +#define USB_SEND 1 /* IN EP */ + +/* + * ### internal used help routines. + */ +#define ep_index(EP) ((EP)->ep.desc->bEndpointAddress&0xF) +#define ep_maxpacket(EP) ((EP)->ep.maxpacket) +#define ep_is_in(EP) ( (ep_index(EP) == 0) ? (EP->udc->ep0_dir == \ + USB_DIR_IN) : ((EP)->ep.desc->bEndpointAddress \ + & USB_DIR_IN)==USB_DIR_IN) +#define get_ep_by_pipe(udc, pipe) ((pipe == 1)? &udc->eps[0]: \ + &udc->eps[pipe]) +#define get_pipe_by_windex(windex) ((windex & USB_ENDPOINT_NUMBER_MASK) \ + * 2 + ((windex & USB_DIR_IN) ? 1 : 0)) +#define get_pipe_by_ep(EP) (ep_index(EP) * 2 + ep_is_in(EP)) + +static inline struct ep_queue_head *get_qh_by_ep(struct fsl_ep *ep) +{ + /* we only have one ep0 structure but two queue heads */ + if (ep_index(ep) != 0) + return ep->qh; + else + return &ep->udc->ep_qh[(ep->udc->ep0_dir == + USB_DIR_IN) ? 1 : 0]; +} + +#endif |