diff options
Diffstat (limited to 'drivers/usb/mtu3/mtu3.h')
| -rw-r--r-- | drivers/usb/mtu3/mtu3.h | 440 |
1 files changed, 440 insertions, 0 deletions
diff --git a/drivers/usb/mtu3/mtu3.h b/drivers/usb/mtu3/mtu3.h new file mode 100644 index 000000000..2d7b57e07 --- /dev/null +++ b/drivers/usb/mtu3/mtu3.h @@ -0,0 +1,440 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * mtu3.h - MediaTek USB3 DRD header + * + * Copyright (C) 2016 MediaTek Inc. + * + * Author: Chunfeng Yun <chunfeng.yun@mediatek.com> + */ + +#ifndef __MTU3_H__ +#define __MTU3_H__ + +#include <linux/clk.h> +#include <linux/device.h> +#include <linux/dmapool.h> +#include <linux/extcon.h> +#include <linux/interrupt.h> +#include <linux/list.h> +#include <linux/phy/phy.h> +#include <linux/regulator/consumer.h> +#include <linux/usb.h> +#include <linux/usb/ch9.h> +#include <linux/usb/gadget.h> +#include <linux/usb/otg.h> +#include <linux/usb/role.h> + +struct mtu3; +struct mtu3_ep; +struct mtu3_request; + +#include "mtu3_hw_regs.h" +#include "mtu3_qmu.h" + +#define MU3D_EP_TXCR0(epnum) (U3D_TX1CSR0 + (((epnum) - 1) * 0x10)) +#define MU3D_EP_TXCR1(epnum) (U3D_TX1CSR1 + (((epnum) - 1) * 0x10)) +#define MU3D_EP_TXCR2(epnum) (U3D_TX1CSR2 + (((epnum) - 1) * 0x10)) + +#define MU3D_EP_RXCR0(epnum) (U3D_RX1CSR0 + (((epnum) - 1) * 0x10)) +#define MU3D_EP_RXCR1(epnum) (U3D_RX1CSR1 + (((epnum) - 1) * 0x10)) +#define MU3D_EP_RXCR2(epnum) (U3D_RX1CSR2 + (((epnum) - 1) * 0x10)) + +#define USB_QMU_TQHIAR(epnum) (U3D_TXQHIAR1 + (((epnum) - 1) * 0x4)) +#define USB_QMU_RQHIAR(epnum) (U3D_RXQHIAR1 + (((epnum) - 1) * 0x4)) + +#define USB_QMU_RQCSR(epnum) (U3D_RXQCSR1 + (((epnum) - 1) * 0x10)) +#define USB_QMU_RQSAR(epnum) (U3D_RXQSAR1 + (((epnum) - 1) * 0x10)) +#define USB_QMU_RQCPR(epnum) (U3D_RXQCPR1 + (((epnum) - 1) * 0x10)) + +#define USB_QMU_TQCSR(epnum) (U3D_TXQCSR1 + (((epnum) - 1) * 0x10)) +#define USB_QMU_TQSAR(epnum) (U3D_TXQSAR1 + (((epnum) - 1) * 0x10)) +#define USB_QMU_TQCPR(epnum) (U3D_TXQCPR1 + (((epnum) - 1) * 0x10)) + +#define SSUSB_U3_CTRL(p) (U3D_SSUSB_U3_CTRL_0P + ((p) * 0x08)) +#define SSUSB_U2_CTRL(p) (U3D_SSUSB_U2_CTRL_0P + ((p) * 0x08)) + +#define MTU3_DRIVER_NAME "mtu3" +#define DMA_ADDR_INVALID (~(dma_addr_t)0) + +#define MTU3_EP_ENABLED BIT(0) +#define MTU3_EP_STALL BIT(1) +#define MTU3_EP_WEDGE BIT(2) +#define MTU3_EP_BUSY BIT(3) + +#define MTU3_U3_IP_SLOT_DEFAULT 2 +#define MTU3_U2_IP_SLOT_DEFAULT 1 + +/** + * IP TRUNK version + * from 0x1003 version, USB3 Gen2 is supported, two changes affect driver: + * 1. MAXPKT and MULTI bits layout of TXCSR1 and RXCSR1 are adjusted, + * but not backward compatible + * 2. QMU extend buffer length supported + */ +#define MTU3_TRUNK_VERS_1003 0x1003 + +/** + * Normally the device works on HS or SS, to simplify fifo management, + * devide fifo into some 512B parts, use bitmap to manage it; And + * 128 bits size of bitmap is large enough, that means it can manage + * up to 64KB fifo size. + * NOTE: MTU3_EP_FIFO_UNIT should be power of two + */ +#define MTU3_EP_FIFO_UNIT (1 << 9) +#define MTU3_FIFO_BIT_SIZE 128 +#define MTU3_U2_IP_EP0_FIFO_SIZE 64 + +/** + * Maximum size of ep0 response buffer for ch9 requests, + * the SET_SEL request uses 6 so far, and GET_STATUS is 2 + */ +#define EP0_RESPONSE_BUF 6 + +#define BULK_CLKS_CNT 4 + +/* device operated link and speed got from DEVICE_CONF register */ +enum mtu3_speed { + MTU3_SPEED_INACTIVE = 0, + MTU3_SPEED_FULL = 1, + MTU3_SPEED_HIGH = 3, + MTU3_SPEED_SUPER = 4, + MTU3_SPEED_SUPER_PLUS = 5, +}; + +/** + * @MU3D_EP0_STATE_SETUP: waits for SETUP or received a SETUP + * without data stage. + * @MU3D_EP0_STATE_TX: IN data stage + * @MU3D_EP0_STATE_RX: OUT data stage + * @MU3D_EP0_STATE_TX_END: the last IN data is transferred, and + * waits for its completion interrupt + * @MU3D_EP0_STATE_STALL: ep0 is in stall status, will be auto-cleared + * after receives a SETUP. + */ +enum mtu3_g_ep0_state { + MU3D_EP0_STATE_SETUP = 1, + MU3D_EP0_STATE_TX, + MU3D_EP0_STATE_RX, + MU3D_EP0_STATE_TX_END, + MU3D_EP0_STATE_STALL, +}; + +/** + * MTU3_DR_FORCE_NONE: automatically switch host and periperal mode + * by IDPIN signal. + * MTU3_DR_FORCE_HOST: force to enter host mode and override OTG + * IDPIN signal. + * MTU3_DR_FORCE_DEVICE: force to enter peripheral mode. + */ +enum mtu3_dr_force_mode { + MTU3_DR_FORCE_NONE = 0, + MTU3_DR_FORCE_HOST, + MTU3_DR_FORCE_DEVICE, +}; + +/** + * @base: the base address of fifo + * @limit: the bitmap size in bits + * @bitmap: fifo bitmap in unit of @MTU3_EP_FIFO_UNIT + */ +struct mtu3_fifo_info { + u32 base; + u32 limit; + DECLARE_BITMAP(bitmap, MTU3_FIFO_BIT_SIZE); +}; + +/** + * General Purpose Descriptor (GPD): + * The format of TX GPD is a little different from RX one. + * And the size of GPD is 16 bytes. + * + * @dw0_info: + * bit0: Hardware Own (HWO) + * bit1: Buffer Descriptor Present (BDP), always 0, BD is not supported + * bit2: Bypass (BPS), 1: HW skips this GPD if HWO = 1 + * bit6: [EL] Zero Length Packet (ZLP), moved from @dw3_info[29] + * bit7: Interrupt On Completion (IOC) + * bit[31:16]: ([EL] bit[31:12]) allow data buffer length (RX ONLY), + * the buffer length of the data to receive + * bit[23:16]: ([EL] bit[31:24]) extension address (TX ONLY), + * lower 4 bits are extension bits of @buffer, + * upper 4 bits are extension bits of @next_gpd + * @next_gpd: Physical address of the next GPD + * @buffer: Physical address of the data buffer + * @dw3_info: + * bit[15:0]: ([EL] bit[19:0]) data buffer length, + * (TX): the buffer length of the data to transmit + * (RX): The total length of data received + * bit[23:16]: ([EL] bit[31:24]) extension address (RX ONLY), + * lower 4 bits are extension bits of @buffer, + * upper 4 bits are extension bits of @next_gpd + * bit29: ([EL] abandoned) Zero Length Packet (ZLP) (TX ONLY) + */ +struct qmu_gpd { + __le32 dw0_info; + __le32 next_gpd; + __le32 buffer; + __le32 dw3_info; +} __packed; + +/** +* dma: physical base address of GPD segment +* start: virtual base address of GPD segment +* end: the last GPD element +* enqueue: the first empty GPD to use +* dequeue: the first completed GPD serviced by ISR +* NOTE: the size of GPD ring should be >= 2 +*/ +struct mtu3_gpd_ring { + dma_addr_t dma; + struct qmu_gpd *start; + struct qmu_gpd *end; + struct qmu_gpd *enqueue; + struct qmu_gpd *dequeue; +}; + +/** +* @vbus: vbus 5V used by host mode +* @edev: external connector used to detect vbus and iddig changes +* @id_nb : notifier for iddig(idpin) detection +* @dr_work : work for drd mode switch, used to avoid sleep in atomic context +* @desired_role : role desired to switch +* @default_role : default mode while usb role is USB_ROLE_NONE +* @role_sw : use USB Role Switch to support dual-role switch, can't use +* extcon at the same time, and extcon is deprecated. +* @role_sw_used : true when the USB Role Switch is used. +* @is_u3_drd: whether port0 supports usb3.0 dual-role device or not +* @manual_drd_enabled: it's true when supports dual-role device by debugfs +* to switch host/device modes depending on user input. +*/ +struct otg_switch_mtk { + struct regulator *vbus; + struct extcon_dev *edev; + struct notifier_block id_nb; + struct work_struct dr_work; + enum usb_role desired_role; + enum usb_role default_role; + struct usb_role_switch *role_sw; + bool role_sw_used; + bool is_u3_drd; + bool manual_drd_enabled; +}; + +/** + * @mac_base: register base address of device MAC, exclude xHCI's + * @ippc_base: register base address of IP Power and Clock interface (IPPC) + * @vusb33: usb3.3V shared by device/host IP + * @dr_mode: works in which mode: + * host only, device only or dual-role mode + * @u2_ports: number of usb2.0 host ports + * @u3_ports: number of usb3.0 host ports + * @u2p_dis_msk: mask of disabling usb2 ports, e.g. bit0==1 to + * disable u2port0, bit1==1 to disable u2port1,... etc, + * but when use dual-role mode, can't disable u2port0 + * @u3p_dis_msk: mask of disabling usb3 ports, for example, bit0==1 to + * disable u3port0, bit1==1 to disable u3port1,... etc + * @dbgfs_root: only used when supports manual dual-role switch via debugfs + * @uwk_en: it's true when supports remote wakeup in host mode + * @uwk: syscon including usb wakeup glue layer between SSUSB IP and SPM + * @uwk_reg_base: the base address of the wakeup glue layer in @uwk + * @uwk_vers: the version of the wakeup glue layer + */ +struct ssusb_mtk { + struct device *dev; + struct mtu3 *u3d; + void __iomem *mac_base; + void __iomem *ippc_base; + struct phy **phys; + int num_phys; + int wakeup_irq; + /* common power & clock */ + struct regulator *vusb33; + struct clk_bulk_data clks[BULK_CLKS_CNT]; + /* otg */ + struct otg_switch_mtk otg_switch; + enum usb_dr_mode dr_mode; + bool is_host; + int u2_ports; + int u3_ports; + int u2p_dis_msk; + int u3p_dis_msk; + struct dentry *dbgfs_root; + /* usb wakeup for host mode */ + bool uwk_en; + struct regmap *uwk; + u32 uwk_reg_base; + u32 uwk_vers; +}; + +/** + * @fifo_size: it is (@slot + 1) * @fifo_seg_size + * @fifo_seg_size: it is roundup_pow_of_two(@maxp) + */ +struct mtu3_ep { + struct usb_ep ep; + char name[12]; + struct mtu3 *mtu; + u8 epnum; + u8 type; + u8 is_in; + u16 maxp; + int slot; + u32 fifo_size; + u32 fifo_addr; + u32 fifo_seg_size; + struct mtu3_fifo_info *fifo; + + struct list_head req_list; + struct mtu3_gpd_ring gpd_ring; + const struct usb_ss_ep_comp_descriptor *comp_desc; + const struct usb_endpoint_descriptor *desc; + + int flags; +}; + +struct mtu3_request { + struct usb_request request; + struct list_head list; + struct mtu3_ep *mep; + struct mtu3 *mtu; + struct qmu_gpd *gpd; + int epnum; +}; + +static inline struct ssusb_mtk *dev_to_ssusb(struct device *dev) +{ + return dev_get_drvdata(dev); +} + +/** + * struct mtu3 - device driver instance data. + * @slot: MTU3_U2_IP_SLOT_DEFAULT for U2 IP only, + * MTU3_U3_IP_SLOT_DEFAULT for U3 IP + * @may_wakeup: means device's remote wakeup is enabled + * @is_self_powered: is reported in device status and the config descriptor + * @delayed_status: true when function drivers ask for delayed status + * @gen2cp: compatible with USB3 Gen2 IP + * @ep0_req: dummy request used while handling standard USB requests + * for GET_STATUS and SET_SEL + * @setup_buf: ep0 response buffer for GET_STATUS and SET_SEL requests + * @u3_capable: is capable of supporting USB3 + */ +struct mtu3 { + spinlock_t lock; + struct ssusb_mtk *ssusb; + struct device *dev; + void __iomem *mac_base; + void __iomem *ippc_base; + int irq; + + struct mtu3_fifo_info tx_fifo; + struct mtu3_fifo_info rx_fifo; + + struct mtu3_ep *ep_array; + struct mtu3_ep *in_eps; + struct mtu3_ep *out_eps; + struct mtu3_ep *ep0; + int num_eps; + int slot; + int active_ep; + + struct dma_pool *qmu_gpd_pool; + enum mtu3_g_ep0_state ep0_state; + struct usb_gadget g; /* the gadget */ + struct usb_gadget_driver *gadget_driver; + struct mtu3_request ep0_req; + u8 setup_buf[EP0_RESPONSE_BUF]; + enum usb_device_speed max_speed; + enum usb_device_speed speed; + + unsigned is_active:1; + unsigned may_wakeup:1; + unsigned is_self_powered:1; + unsigned test_mode:1; + unsigned softconnect:1; + unsigned u1_enable:1; + unsigned u2_enable:1; + unsigned u3_capable:1; + unsigned delayed_status:1; + unsigned gen2cp:1; + unsigned connected:1; + unsigned async_callbacks:1; + unsigned separate_fifo:1; + + u8 address; + u8 test_mode_nr; + u32 hw_version; +}; + +static inline struct mtu3 *gadget_to_mtu3(struct usb_gadget *g) +{ + return container_of(g, struct mtu3, g); +} + +static inline struct mtu3_request *to_mtu3_request(struct usb_request *req) +{ + return req ? container_of(req, struct mtu3_request, request) : NULL; +} + +static inline struct mtu3_ep *to_mtu3_ep(struct usb_ep *ep) +{ + return ep ? container_of(ep, struct mtu3_ep, ep) : NULL; +} + +static inline struct mtu3_request *next_request(struct mtu3_ep *mep) +{ + return list_first_entry_or_null(&mep->req_list, struct mtu3_request, + list); +} + +static inline void mtu3_writel(void __iomem *base, u32 offset, u32 data) +{ + writel(data, base + offset); +} + +static inline u32 mtu3_readl(void __iomem *base, u32 offset) +{ + return readl(base + offset); +} + +static inline void mtu3_setbits(void __iomem *base, u32 offset, u32 bits) +{ + void __iomem *addr = base + offset; + u32 tmp = readl(addr); + + writel((tmp | (bits)), addr); +} + +static inline void mtu3_clrbits(void __iomem *base, u32 offset, u32 bits) +{ + void __iomem *addr = base + offset; + u32 tmp = readl(addr); + + writel((tmp & ~(bits)), addr); +} + +int ssusb_check_clocks(struct ssusb_mtk *ssusb, u32 ex_clks); +struct usb_request *mtu3_alloc_request(struct usb_ep *ep, gfp_t gfp_flags); +void mtu3_free_request(struct usb_ep *ep, struct usb_request *req); +void mtu3_req_complete(struct mtu3_ep *mep, + struct usb_request *req, int status); + +int mtu3_config_ep(struct mtu3 *mtu, struct mtu3_ep *mep, + int interval, int burst, int mult); +void mtu3_deconfig_ep(struct mtu3 *mtu, struct mtu3_ep *mep); +void mtu3_ep_stall_set(struct mtu3_ep *mep, bool set); +void mtu3_start(struct mtu3 *mtu); +void mtu3_stop(struct mtu3 *mtu); +void mtu3_dev_on_off(struct mtu3 *mtu, int is_on); + +int mtu3_gadget_setup(struct mtu3 *mtu); +void mtu3_gadget_cleanup(struct mtu3 *mtu); +void mtu3_gadget_reset(struct mtu3 *mtu); +void mtu3_gadget_suspend(struct mtu3 *mtu); +void mtu3_gadget_resume(struct mtu3 *mtu); +void mtu3_gadget_disconnect(struct mtu3 *mtu); + +irqreturn_t mtu3_ep0_isr(struct mtu3 *mtu); +extern const struct usb_ep_ops mtu3_ep0_ops; + +#endif |