diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/usb/phy/phy-ab8500-usb.c | 1013 |
1 files changed, 1013 insertions, 0 deletions
diff --git a/drivers/usb/phy/phy-ab8500-usb.c b/drivers/usb/phy/phy-ab8500-usb.c new file mode 100644 index 000000000..4c52ba96f --- /dev/null +++ b/drivers/usb/phy/phy-ab8500-usb.c @@ -0,0 +1,1013 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * USB transceiver driver for AB8500 family chips + * + * Copyright (C) 2010-2013 ST-Ericsson AB + * Mian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com> + * Avinash Kumar <avinash.kumar@stericsson.com> + * Thirupathi Chippakurthy <thirupathi.chippakurthy@stericsson.com> + */ + +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/usb/otg.h> +#include <linux/slab.h> +#include <linux/notifier.h> +#include <linux/interrupt.h> +#include <linux/delay.h> +#include <linux/clk.h> +#include <linux/err.h> +#include <linux/mfd/abx500.h> +#include <linux/mfd/abx500/ab8500.h> +#include <linux/usb/musb-ux500.h> +#include <linux/regulator/consumer.h> +#include <linux/pinctrl/consumer.h> + +/* Bank AB8500_SYS_CTRL2_BLOCK */ +#define AB8500_MAIN_WD_CTRL_REG 0x01 + +/* Bank AB8500_USB */ +#define AB8500_USB_LINE_STAT_REG 0x80 +#define AB8505_USB_LINE_STAT_REG 0x94 +#define AB8500_USB_PHY_CTRL_REG 0x8A + +/* Bank AB8500_DEVELOPMENT */ +#define AB8500_BANK12_ACCESS 0x00 + +/* Bank AB8500_DEBUG */ +#define AB8500_USB_PHY_TUNE1 0x05 +#define AB8500_USB_PHY_TUNE2 0x06 +#define AB8500_USB_PHY_TUNE3 0x07 + +/* Bank AB8500_INTERRUPT */ +#define AB8500_IT_SOURCE2_REG 0x01 + +#define AB8500_BIT_OTG_STAT_ID (1 << 0) +#define AB8500_BIT_PHY_CTRL_HOST_EN (1 << 0) +#define AB8500_BIT_PHY_CTRL_DEVICE_EN (1 << 1) +#define AB8500_BIT_WD_CTRL_ENABLE (1 << 0) +#define AB8500_BIT_WD_CTRL_KICK (1 << 1) +#define AB8500_BIT_SOURCE2_VBUSDET (1 << 7) + +#define AB8500_WD_KICK_DELAY_US 100 /* usec */ +#define AB8500_WD_V11_DISABLE_DELAY_US 100 /* usec */ +#define AB8500_V20_31952_DISABLE_DELAY_US 100 /* usec */ + +/* Usb line status register */ +enum ab8500_usb_link_status { + USB_LINK_NOT_CONFIGURED_8500 = 0, + USB_LINK_STD_HOST_NC_8500, + USB_LINK_STD_HOST_C_NS_8500, + USB_LINK_STD_HOST_C_S_8500, + USB_LINK_HOST_CHG_NM_8500, + USB_LINK_HOST_CHG_HS_8500, + USB_LINK_HOST_CHG_HS_CHIRP_8500, + USB_LINK_DEDICATED_CHG_8500, + USB_LINK_ACA_RID_A_8500, + USB_LINK_ACA_RID_B_8500, + USB_LINK_ACA_RID_C_NM_8500, + USB_LINK_ACA_RID_C_HS_8500, + USB_LINK_ACA_RID_C_HS_CHIRP_8500, + USB_LINK_HM_IDGND_8500, + USB_LINK_RESERVED_8500, + USB_LINK_NOT_VALID_LINK_8500, +}; + +enum ab8505_usb_link_status { + USB_LINK_NOT_CONFIGURED_8505 = 0, + USB_LINK_STD_HOST_NC_8505, + USB_LINK_STD_HOST_C_NS_8505, + USB_LINK_STD_HOST_C_S_8505, + USB_LINK_CDP_8505, + USB_LINK_RESERVED0_8505, + USB_LINK_RESERVED1_8505, + USB_LINK_DEDICATED_CHG_8505, + USB_LINK_ACA_RID_A_8505, + USB_LINK_ACA_RID_B_8505, + USB_LINK_ACA_RID_C_NM_8505, + USB_LINK_RESERVED2_8505, + USB_LINK_RESERVED3_8505, + USB_LINK_HM_IDGND_8505, + USB_LINK_CHARGERPORT_NOT_OK_8505, + USB_LINK_CHARGER_DM_HIGH_8505, + USB_LINK_PHYEN_NO_VBUS_NO_IDGND_8505, + USB_LINK_STD_UPSTREAM_NO_IDGNG_NO_VBUS_8505, + USB_LINK_STD_UPSTREAM_8505, + USB_LINK_CHARGER_SE1_8505, + USB_LINK_CARKIT_CHGR_1_8505, + USB_LINK_CARKIT_CHGR_2_8505, + USB_LINK_ACA_DOCK_CHGR_8505, + USB_LINK_SAMSUNG_BOOT_CBL_PHY_EN_8505, + USB_LINK_SAMSUNG_BOOT_CBL_PHY_DISB_8505, + USB_LINK_SAMSUNG_UART_CBL_PHY_EN_8505, + USB_LINK_SAMSUNG_UART_CBL_PHY_DISB_8505, + USB_LINK_MOTOROLA_FACTORY_CBL_PHY_EN_8505, +}; + +enum ab8500_usb_mode { + USB_IDLE = 0, + USB_PERIPHERAL, + USB_HOST, + USB_DEDICATED_CHG, + USB_UART +}; + +/* Register USB_LINK_STATUS interrupt */ +#define AB8500_USB_FLAG_USE_LINK_STATUS_IRQ (1 << 0) +/* Register ID_WAKEUP_F interrupt */ +#define AB8500_USB_FLAG_USE_ID_WAKEUP_IRQ (1 << 1) +/* Register VBUS_DET_F interrupt */ +#define AB8500_USB_FLAG_USE_VBUS_DET_IRQ (1 << 2) +/* Driver is using the ab-iddet driver*/ +#define AB8500_USB_FLAG_USE_AB_IDDET (1 << 3) +/* Enable setting regulators voltage */ +#define AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE (1 << 4) + +struct ab8500_usb { + struct usb_phy phy; + struct device *dev; + struct ab8500 *ab8500; + unsigned vbus_draw; + struct work_struct phy_dis_work; + enum ab8500_usb_mode mode; + struct clk *sysclk; + struct regulator *v_ape; + struct regulator *v_musb; + struct regulator *v_ulpi; + int saved_v_ulpi; + int previous_link_status_state; + struct pinctrl *pinctrl; + struct pinctrl_state *pins_sleep; + bool enabled_charging_detection; + unsigned int flags; +}; + +static inline struct ab8500_usb *phy_to_ab(struct usb_phy *x) +{ + return container_of(x, struct ab8500_usb, phy); +} + +static void ab8500_usb_wd_workaround(struct ab8500_usb *ab) +{ + abx500_set_register_interruptible(ab->dev, + AB8500_SYS_CTRL2_BLOCK, + AB8500_MAIN_WD_CTRL_REG, + AB8500_BIT_WD_CTRL_ENABLE); + + udelay(AB8500_WD_KICK_DELAY_US); + + abx500_set_register_interruptible(ab->dev, + AB8500_SYS_CTRL2_BLOCK, + AB8500_MAIN_WD_CTRL_REG, + (AB8500_BIT_WD_CTRL_ENABLE + | AB8500_BIT_WD_CTRL_KICK)); + + udelay(AB8500_WD_V11_DISABLE_DELAY_US); + + abx500_set_register_interruptible(ab->dev, + AB8500_SYS_CTRL2_BLOCK, + AB8500_MAIN_WD_CTRL_REG, + 0); +} + +static void ab8500_usb_regulator_enable(struct ab8500_usb *ab) +{ + int ret, volt; + + ret = regulator_enable(ab->v_ape); + if (ret) + dev_err(ab->dev, "Failed to enable v-ape\n"); + + if (ab->flags & AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE) { + ab->saved_v_ulpi = regulator_get_voltage(ab->v_ulpi); + if (ab->saved_v_ulpi < 0) + dev_err(ab->dev, "Failed to get v_ulpi voltage\n"); + + ret = regulator_set_voltage(ab->v_ulpi, 1300000, 1350000); + if (ret < 0) + dev_err(ab->dev, "Failed to set the Vintcore to 1.3V, ret=%d\n", + ret); + + ret = regulator_set_load(ab->v_ulpi, 28000); + if (ret < 0) + dev_err(ab->dev, "Failed to set optimum mode (ret=%d)\n", + ret); + } + + ret = regulator_enable(ab->v_ulpi); + if (ret) + dev_err(ab->dev, "Failed to enable vddulpivio18\n"); + + if (ab->flags & AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE) { + volt = regulator_get_voltage(ab->v_ulpi); + if ((volt != 1300000) && (volt != 1350000)) + dev_err(ab->dev, "Vintcore is not set to 1.3V volt=%d\n", + volt); + } + + ret = regulator_enable(ab->v_musb); + if (ret) + dev_err(ab->dev, "Failed to enable musb_1v8\n"); +} + +static void ab8500_usb_regulator_disable(struct ab8500_usb *ab) +{ + int ret; + + regulator_disable(ab->v_musb); + + regulator_disable(ab->v_ulpi); + + /* USB is not the only consumer of Vintcore, restore old settings */ + if (ab->flags & AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE) { + if (ab->saved_v_ulpi > 0) { + ret = regulator_set_voltage(ab->v_ulpi, + ab->saved_v_ulpi, ab->saved_v_ulpi); + if (ret < 0) + dev_err(ab->dev, "Failed to set the Vintcore to %duV, ret=%d\n", + ab->saved_v_ulpi, ret); + } + + ret = regulator_set_load(ab->v_ulpi, 0); + if (ret < 0) + dev_err(ab->dev, "Failed to set optimum mode (ret=%d)\n", + ret); + } + + regulator_disable(ab->v_ape); +} + +static void ab8500_usb_wd_linkstatus(struct ab8500_usb *ab, u8 bit) +{ + /* Workaround for v2.0 bug # 31952 */ + if (is_ab8500_2p0(ab->ab8500)) { + abx500_mask_and_set_register_interruptible(ab->dev, + AB8500_USB, AB8500_USB_PHY_CTRL_REG, + bit, bit); + udelay(AB8500_V20_31952_DISABLE_DELAY_US); + } +} + +static void ab8500_usb_phy_enable(struct ab8500_usb *ab, bool sel_host) +{ + u8 bit; + bit = sel_host ? AB8500_BIT_PHY_CTRL_HOST_EN : + AB8500_BIT_PHY_CTRL_DEVICE_EN; + + /* mux and configure USB pins to DEFAULT state */ + ab->pinctrl = pinctrl_get_select(ab->dev, PINCTRL_STATE_DEFAULT); + if (IS_ERR(ab->pinctrl)) + dev_err(ab->dev, "could not get/set default pinstate\n"); + + if (clk_prepare_enable(ab->sysclk)) + dev_err(ab->dev, "can't prepare/enable clock\n"); + + ab8500_usb_regulator_enable(ab); + + abx500_mask_and_set_register_interruptible(ab->dev, + AB8500_USB, AB8500_USB_PHY_CTRL_REG, + bit, bit); +} + +static void ab8500_usb_phy_disable(struct ab8500_usb *ab, bool sel_host) +{ + u8 bit; + bit = sel_host ? AB8500_BIT_PHY_CTRL_HOST_EN : + AB8500_BIT_PHY_CTRL_DEVICE_EN; + + ab8500_usb_wd_linkstatus(ab, bit); + + abx500_mask_and_set_register_interruptible(ab->dev, + AB8500_USB, AB8500_USB_PHY_CTRL_REG, + bit, 0); + + /* Needed to disable the phy.*/ + ab8500_usb_wd_workaround(ab); + + clk_disable_unprepare(ab->sysclk); + + ab8500_usb_regulator_disable(ab); + + if (!IS_ERR(ab->pinctrl)) { + /* configure USB pins to SLEEP state */ + ab->pins_sleep = pinctrl_lookup_state(ab->pinctrl, + PINCTRL_STATE_SLEEP); + + if (IS_ERR(ab->pins_sleep)) + dev_dbg(ab->dev, "could not get sleep pinstate\n"); + else if (pinctrl_select_state(ab->pinctrl, ab->pins_sleep)) + dev_err(ab->dev, "could not set pins to sleep state\n"); + + /* + * as USB pins are shared with iddet, release them to allow + * iddet to request them + */ + pinctrl_put(ab->pinctrl); + } +} + +#define ab8500_usb_host_phy_en(ab) ab8500_usb_phy_enable(ab, true) +#define ab8500_usb_host_phy_dis(ab) ab8500_usb_phy_disable(ab, true) +#define ab8500_usb_peri_phy_en(ab) ab8500_usb_phy_enable(ab, false) +#define ab8500_usb_peri_phy_dis(ab) ab8500_usb_phy_disable(ab, false) + +static int ab8505_usb_link_status_update(struct ab8500_usb *ab, + enum ab8505_usb_link_status lsts) +{ + enum ux500_musb_vbus_id_status event = 0; + + dev_dbg(ab->dev, "ab8505_usb_link_status_update %d\n", lsts); + + /* + * Spurious link_status interrupts are seen at the time of + * disconnection of a device in RIDA state + */ + if (ab->previous_link_status_state == USB_LINK_ACA_RID_A_8505 && + (lsts == USB_LINK_STD_HOST_NC_8505)) + return 0; + + ab->previous_link_status_state = lsts; + + switch (lsts) { + case USB_LINK_ACA_RID_B_8505: + event = UX500_MUSB_RIDB; + fallthrough; + case USB_LINK_NOT_CONFIGURED_8505: + case USB_LINK_RESERVED0_8505: + case USB_LINK_RESERVED1_8505: + case USB_LINK_RESERVED2_8505: + case USB_LINK_RESERVED3_8505: + ab->mode = USB_IDLE; + ab->phy.otg->default_a = false; + ab->vbus_draw = 0; + if (event != UX500_MUSB_RIDB) + event = UX500_MUSB_NONE; + /* + * Fallback to default B_IDLE as nothing + * is connected + */ + ab->phy.otg->state = OTG_STATE_B_IDLE; + usb_phy_set_event(&ab->phy, USB_EVENT_NONE); + break; + + case USB_LINK_ACA_RID_C_NM_8505: + event = UX500_MUSB_RIDC; + fallthrough; + case USB_LINK_STD_HOST_NC_8505: + case USB_LINK_STD_HOST_C_NS_8505: + case USB_LINK_STD_HOST_C_S_8505: + case USB_LINK_CDP_8505: + if (ab->mode == USB_IDLE) { + ab->mode = USB_PERIPHERAL; + ab8500_usb_peri_phy_en(ab); + atomic_notifier_call_chain(&ab->phy.notifier, + UX500_MUSB_PREPARE, &ab->vbus_draw); + usb_phy_set_event(&ab->phy, USB_EVENT_ENUMERATED); + } + if (event != UX500_MUSB_RIDC) + event = UX500_MUSB_VBUS; + break; + + case USB_LINK_ACA_RID_A_8505: + case USB_LINK_ACA_DOCK_CHGR_8505: + event = UX500_MUSB_RIDA; + fallthrough; + case USB_LINK_HM_IDGND_8505: + if (ab->mode == USB_IDLE) { + ab->mode = USB_HOST; + ab8500_usb_host_phy_en(ab); + atomic_notifier_call_chain(&ab->phy.notifier, + UX500_MUSB_PREPARE, &ab->vbus_draw); + } + ab->phy.otg->default_a = true; + if (event != UX500_MUSB_RIDA) + event = UX500_MUSB_ID; + atomic_notifier_call_chain(&ab->phy.notifier, + event, &ab->vbus_draw); + break; + + case USB_LINK_DEDICATED_CHG_8505: + ab->mode = USB_DEDICATED_CHG; + event = UX500_MUSB_CHARGER; + atomic_notifier_call_chain(&ab->phy.notifier, + event, &ab->vbus_draw); + usb_phy_set_event(&ab->phy, USB_EVENT_CHARGER); + break; + + /* + * FIXME: For now we rely on the boot firmware to set up the necessary + * PHY/pin configuration for UART mode. + * + * AB8505 does not seem to report any status change for UART cables, + * possibly because it cannot detect them autonomously. + * We may need to measure the ID resistance manually to reliably + * detect UART cables after bootup. + */ + case USB_LINK_SAMSUNG_UART_CBL_PHY_EN_8505: + case USB_LINK_SAMSUNG_UART_CBL_PHY_DISB_8505: + if (ab->mode == USB_IDLE) { + ab->mode = USB_UART; + ab8500_usb_peri_phy_en(ab); + } + + break; + + default: + break; + } + + return 0; +} + +static int ab8500_usb_link_status_update(struct ab8500_usb *ab, + enum ab8500_usb_link_status lsts) +{ + enum ux500_musb_vbus_id_status event = 0; + + dev_dbg(ab->dev, "ab8500_usb_link_status_update %d\n", lsts); + + /* + * Spurious link_status interrupts are seen in case of a + * disconnection of a device in IDGND and RIDA stage + */ + if (ab->previous_link_status_state == USB_LINK_HM_IDGND_8500 && + (lsts == USB_LINK_STD_HOST_C_NS_8500 || + lsts == USB_LINK_STD_HOST_NC_8500)) + return 0; + + if (ab->previous_link_status_state == USB_LINK_ACA_RID_A_8500 && + lsts == USB_LINK_STD_HOST_NC_8500) + return 0; + + ab->previous_link_status_state = lsts; + + switch (lsts) { + case USB_LINK_ACA_RID_B_8500: + event = UX500_MUSB_RIDB; + fallthrough; + case USB_LINK_NOT_CONFIGURED_8500: + case USB_LINK_NOT_VALID_LINK_8500: + ab->mode = USB_IDLE; + ab->phy.otg->default_a = false; + ab->vbus_draw = 0; + if (event != UX500_MUSB_RIDB) + event = UX500_MUSB_NONE; + /* Fallback to default B_IDLE as nothing is connected */ + ab->phy.otg->state = OTG_STATE_B_IDLE; + usb_phy_set_event(&ab->phy, USB_EVENT_NONE); + break; + + case USB_LINK_ACA_RID_C_NM_8500: + case USB_LINK_ACA_RID_C_HS_8500: + case USB_LINK_ACA_RID_C_HS_CHIRP_8500: + event = UX500_MUSB_RIDC; + fallthrough; + case USB_LINK_STD_HOST_NC_8500: + case USB_LINK_STD_HOST_C_NS_8500: + case USB_LINK_STD_HOST_C_S_8500: + case USB_LINK_HOST_CHG_NM_8500: + case USB_LINK_HOST_CHG_HS_8500: + case USB_LINK_HOST_CHG_HS_CHIRP_8500: + if (ab->mode == USB_IDLE) { + ab->mode = USB_PERIPHERAL; + ab8500_usb_peri_phy_en(ab); + atomic_notifier_call_chain(&ab->phy.notifier, + UX500_MUSB_PREPARE, &ab->vbus_draw); + usb_phy_set_event(&ab->phy, USB_EVENT_ENUMERATED); + } + if (event != UX500_MUSB_RIDC) + event = UX500_MUSB_VBUS; + break; + + case USB_LINK_ACA_RID_A_8500: + event = UX500_MUSB_RIDA; + fallthrough; + case USB_LINK_HM_IDGND_8500: + if (ab->mode == USB_IDLE) { + ab->mode = USB_HOST; + ab8500_usb_host_phy_en(ab); + atomic_notifier_call_chain(&ab->phy.notifier, + UX500_MUSB_PREPARE, &ab->vbus_draw); + } + ab->phy.otg->default_a = true; + if (event != UX500_MUSB_RIDA) + event = UX500_MUSB_ID; + atomic_notifier_call_chain(&ab->phy.notifier, + event, &ab->vbus_draw); + break; + + case USB_LINK_DEDICATED_CHG_8500: + ab->mode = USB_DEDICATED_CHG; + event = UX500_MUSB_CHARGER; + atomic_notifier_call_chain(&ab->phy.notifier, + event, &ab->vbus_draw); + usb_phy_set_event(&ab->phy, USB_EVENT_CHARGER); + break; + + case USB_LINK_RESERVED_8500: + break; + } + + return 0; +} + +/* + * Connection Sequence: + * 1. Link Status Interrupt + * 2. Enable AB clock + * 3. Enable AB regulators + * 4. Enable USB phy + * 5. Reset the musb controller + * 6. Switch the ULPI GPIO pins to function mode + * 7. Enable the musb Peripheral5 clock + * 8. Restore MUSB context + */ +static int abx500_usb_link_status_update(struct ab8500_usb *ab) +{ + u8 reg; + int ret = 0; + + if (is_ab8500(ab->ab8500)) { + enum ab8500_usb_link_status lsts; + + ret = abx500_get_register_interruptible(ab->dev, + AB8500_USB, AB8500_USB_LINE_STAT_REG, ®); + if (ret < 0) + return ret; + lsts = (reg >> 3) & 0x0F; + ret = ab8500_usb_link_status_update(ab, lsts); + } else if (is_ab8505(ab->ab8500)) { + enum ab8505_usb_link_status lsts; + + ret = abx500_get_register_interruptible(ab->dev, + AB8500_USB, AB8505_USB_LINE_STAT_REG, ®); + if (ret < 0) + return ret; + lsts = (reg >> 3) & 0x1F; + ret = ab8505_usb_link_status_update(ab, lsts); + } + + return ret; +} + +/* + * Disconnection Sequence: + * 1. Disconnect Interrupt + * 2. Disable regulators + * 3. Disable AB clock + * 4. Disable the Phy + * 5. Link Status Interrupt + * 6. Disable Musb Clock + */ +static irqreturn_t ab8500_usb_disconnect_irq(int irq, void *data) +{ + struct ab8500_usb *ab = (struct ab8500_usb *) data; + enum usb_phy_events event = USB_EVENT_NONE; + + /* Link status will not be updated till phy is disabled. */ + if (ab->mode == USB_HOST) { + ab->phy.otg->default_a = false; + ab->vbus_draw = 0; + atomic_notifier_call_chain(&ab->phy.notifier, + event, &ab->vbus_draw); + ab8500_usb_host_phy_dis(ab); + ab->mode = USB_IDLE; + } + + if (ab->mode == USB_PERIPHERAL) { + atomic_notifier_call_chain(&ab->phy.notifier, + event, &ab->vbus_draw); + ab8500_usb_peri_phy_dis(ab); + atomic_notifier_call_chain(&ab->phy.notifier, + UX500_MUSB_CLEAN, &ab->vbus_draw); + ab->mode = USB_IDLE; + ab->phy.otg->default_a = false; + ab->vbus_draw = 0; + } + + if (ab->mode == USB_UART) { + ab8500_usb_peri_phy_dis(ab); + ab->mode = USB_IDLE; + } + + if (is_ab8500_2p0(ab->ab8500)) { + if (ab->mode == USB_DEDICATED_CHG) { + ab8500_usb_wd_linkstatus(ab, + AB8500_BIT_PHY_CTRL_DEVICE_EN); + abx500_mask_and_set_register_interruptible(ab->dev, + AB8500_USB, AB8500_USB_PHY_CTRL_REG, + AB8500_BIT_PHY_CTRL_DEVICE_EN, 0); + } + } + + return IRQ_HANDLED; +} + +static irqreturn_t ab8500_usb_link_status_irq(int irq, void *data) +{ + struct ab8500_usb *ab = (struct ab8500_usb *)data; + + abx500_usb_link_status_update(ab); + + return IRQ_HANDLED; +} + +static void ab8500_usb_phy_disable_work(struct work_struct *work) +{ + struct ab8500_usb *ab = container_of(work, struct ab8500_usb, + phy_dis_work); + + if (!ab->phy.otg->host) + ab8500_usb_host_phy_dis(ab); + + if (!ab->phy.otg->gadget) + ab8500_usb_peri_phy_dis(ab); +} + +static int ab8500_usb_set_suspend(struct usb_phy *x, int suspend) +{ + /* TODO */ + return 0; +} + +static int ab8500_usb_set_peripheral(struct usb_otg *otg, + struct usb_gadget *gadget) +{ + struct ab8500_usb *ab; + + if (!otg) + return -ENODEV; + + ab = phy_to_ab(otg->usb_phy); + + ab->phy.otg->gadget = gadget; + + /* Some drivers call this function in atomic context. + * Do not update ab8500 registers directly till this + * is fixed. + */ + + if ((ab->mode != USB_IDLE) && !gadget) { + ab->mode = USB_IDLE; + schedule_work(&ab->phy_dis_work); + } + + return 0; +} + +static int ab8500_usb_set_host(struct usb_otg *otg, struct usb_bus *host) +{ + struct ab8500_usb *ab; + + if (!otg) + return -ENODEV; + + ab = phy_to_ab(otg->usb_phy); + + ab->phy.otg->host = host; + + /* Some drivers call this function in atomic context. + * Do not update ab8500 registers directly till this + * is fixed. + */ + + if ((ab->mode != USB_IDLE) && !host) { + ab->mode = USB_IDLE; + schedule_work(&ab->phy_dis_work); + } + + return 0; +} + +static void ab8500_usb_restart_phy(struct ab8500_usb *ab) +{ + abx500_mask_and_set_register_interruptible(ab->dev, + AB8500_USB, AB8500_USB_PHY_CTRL_REG, + AB8500_BIT_PHY_CTRL_DEVICE_EN, + AB8500_BIT_PHY_CTRL_DEVICE_EN); + + udelay(100); + + abx500_mask_and_set_register_interruptible(ab->dev, + AB8500_USB, AB8500_USB_PHY_CTRL_REG, + AB8500_BIT_PHY_CTRL_DEVICE_EN, + 0); + + abx500_mask_and_set_register_interruptible(ab->dev, + AB8500_USB, AB8500_USB_PHY_CTRL_REG, + AB8500_BIT_PHY_CTRL_HOST_EN, + AB8500_BIT_PHY_CTRL_HOST_EN); + + udelay(100); + + abx500_mask_and_set_register_interruptible(ab->dev, + AB8500_USB, AB8500_USB_PHY_CTRL_REG, + AB8500_BIT_PHY_CTRL_HOST_EN, + 0); +} + +static int ab8500_usb_regulator_get(struct ab8500_usb *ab) +{ + int err; + + ab->v_ape = devm_regulator_get(ab->dev, "v-ape"); + if (IS_ERR(ab->v_ape)) { + dev_err(ab->dev, "Could not get v-ape supply\n"); + err = PTR_ERR(ab->v_ape); + return err; + } + + ab->v_ulpi = devm_regulator_get(ab->dev, "vddulpivio18"); + if (IS_ERR(ab->v_ulpi)) { + dev_err(ab->dev, "Could not get vddulpivio18 supply\n"); + err = PTR_ERR(ab->v_ulpi); + return err; + } + + ab->v_musb = devm_regulator_get(ab->dev, "musb_1v8"); + if (IS_ERR(ab->v_musb)) { + dev_err(ab->dev, "Could not get musb_1v8 supply\n"); + err = PTR_ERR(ab->v_musb); + return err; + } + + return 0; +} + +static int ab8500_usb_irq_setup(struct platform_device *pdev, + struct ab8500_usb *ab) +{ + int err; + int irq; + + if (ab->flags & AB8500_USB_FLAG_USE_LINK_STATUS_IRQ) { + irq = platform_get_irq_byname(pdev, "USB_LINK_STATUS"); + if (irq < 0) + return irq; + err = devm_request_threaded_irq(&pdev->dev, irq, NULL, + ab8500_usb_link_status_irq, + IRQF_NO_SUSPEND | IRQF_SHARED | IRQF_ONESHOT, + "usb-link-status", ab); + if (err < 0) { + dev_err(ab->dev, "request_irq failed for link status irq\n"); + return err; + } + } + + if (ab->flags & AB8500_USB_FLAG_USE_ID_WAKEUP_IRQ) { + irq = platform_get_irq_byname(pdev, "ID_WAKEUP_F"); + if (irq < 0) + return irq; + err = devm_request_threaded_irq(&pdev->dev, irq, NULL, + ab8500_usb_disconnect_irq, + IRQF_NO_SUSPEND | IRQF_SHARED | IRQF_ONESHOT, + "usb-id-fall", ab); + if (err < 0) { + dev_err(ab->dev, "request_irq failed for ID fall irq\n"); + return err; + } + } + + if (ab->flags & AB8500_USB_FLAG_USE_VBUS_DET_IRQ) { + irq = platform_get_irq_byname(pdev, "VBUS_DET_F"); + if (irq < 0) + return irq; + err = devm_request_threaded_irq(&pdev->dev, irq, NULL, + ab8500_usb_disconnect_irq, + IRQF_NO_SUSPEND | IRQF_SHARED | IRQF_ONESHOT, + "usb-vbus-fall", ab); + if (err < 0) { + dev_err(ab->dev, "request_irq failed for Vbus fall irq\n"); + return err; + } + } + + return 0; +} + +static void ab8500_usb_set_ab8500_tuning_values(struct ab8500_usb *ab) +{ + int err; + + /* Enable the PBT/Bank 0x12 access */ + err = abx500_set_register_interruptible(ab->dev, + AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS, 0x01); + if (err < 0) + dev_err(ab->dev, "Failed to enable bank12 access err=%d\n", + err); + + err = abx500_set_register_interruptible(ab->dev, + AB8500_DEBUG, AB8500_USB_PHY_TUNE1, 0xC8); + if (err < 0) + dev_err(ab->dev, "Failed to set PHY_TUNE1 register err=%d\n", + err); + + err = abx500_set_register_interruptible(ab->dev, + AB8500_DEBUG, AB8500_USB_PHY_TUNE2, 0x00); + if (err < 0) + dev_err(ab->dev, "Failed to set PHY_TUNE2 register err=%d\n", + err); + + err = abx500_set_register_interruptible(ab->dev, + AB8500_DEBUG, AB8500_USB_PHY_TUNE3, 0x78); + if (err < 0) + dev_err(ab->dev, "Failed to set PHY_TUNE3 register err=%d\n", + err); + + /* Switch to normal mode/disable Bank 0x12 access */ + err = abx500_set_register_interruptible(ab->dev, + AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS, 0x00); + if (err < 0) + dev_err(ab->dev, "Failed to switch bank12 access err=%d\n", + err); +} + +static void ab8500_usb_set_ab8505_tuning_values(struct ab8500_usb *ab) +{ + int err; + + /* Enable the PBT/Bank 0x12 access */ + err = abx500_mask_and_set_register_interruptible(ab->dev, + AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS, + 0x01, 0x01); + if (err < 0) + dev_err(ab->dev, "Failed to enable bank12 access err=%d\n", + err); + + err = abx500_mask_and_set_register_interruptible(ab->dev, + AB8500_DEBUG, AB8500_USB_PHY_TUNE1, + 0xC8, 0xC8); + if (err < 0) + dev_err(ab->dev, "Failed to set PHY_TUNE1 register err=%d\n", + err); + + err = abx500_mask_and_set_register_interruptible(ab->dev, + AB8500_DEBUG, AB8500_USB_PHY_TUNE2, + 0x60, 0x60); + if (err < 0) + dev_err(ab->dev, "Failed to set PHY_TUNE2 register err=%d\n", + err); + + err = abx500_mask_and_set_register_interruptible(ab->dev, + AB8500_DEBUG, AB8500_USB_PHY_TUNE3, + 0xFC, 0x80); + + if (err < 0) + dev_err(ab->dev, "Failed to set PHY_TUNE3 register err=%d\n", + err); + + /* Switch to normal mode/disable Bank 0x12 access */ + err = abx500_mask_and_set_register_interruptible(ab->dev, + AB8500_DEVELOPMENT, AB8500_BANK12_ACCESS, + 0x00, 0x00); + if (err < 0) + dev_err(ab->dev, "Failed to switch bank12 access err=%d\n", + err); +} + +static int ab8500_usb_probe(struct platform_device *pdev) +{ + struct ab8500_usb *ab; + struct ab8500 *ab8500; + struct usb_otg *otg; + int err; + int rev; + + ab8500 = dev_get_drvdata(pdev->dev.parent); + rev = abx500_get_chip_id(&pdev->dev); + + if (is_ab8500_1p1_or_earlier(ab8500)) { + dev_err(&pdev->dev, "Unsupported AB8500 chip rev=%d\n", rev); + return -ENODEV; + } + + ab = devm_kzalloc(&pdev->dev, sizeof(*ab), GFP_KERNEL); + if (!ab) + return -ENOMEM; + + otg = devm_kzalloc(&pdev->dev, sizeof(*otg), GFP_KERNEL); + if (!otg) + return -ENOMEM; + + ab->dev = &pdev->dev; + ab->ab8500 = ab8500; + ab->phy.dev = ab->dev; + ab->phy.otg = otg; + ab->phy.label = "ab8500"; + ab->phy.set_suspend = ab8500_usb_set_suspend; + ab->phy.otg->state = OTG_STATE_UNDEFINED; + + otg->usb_phy = &ab->phy; + otg->set_host = ab8500_usb_set_host; + otg->set_peripheral = ab8500_usb_set_peripheral; + + if (is_ab8500(ab->ab8500)) { + ab->flags |= AB8500_USB_FLAG_USE_LINK_STATUS_IRQ | + AB8500_USB_FLAG_USE_ID_WAKEUP_IRQ | + AB8500_USB_FLAG_USE_VBUS_DET_IRQ | + AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE; + } else if (is_ab8505(ab->ab8500)) { + ab->flags |= AB8500_USB_FLAG_USE_LINK_STATUS_IRQ | + AB8500_USB_FLAG_USE_ID_WAKEUP_IRQ | + AB8500_USB_FLAG_USE_VBUS_DET_IRQ | + AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE; + } + + /* Disable regulator voltage setting for AB8500 <= v2.0 */ + if (is_ab8500_2p0_or_earlier(ab->ab8500)) + ab->flags &= ~AB8500_USB_FLAG_REGULATOR_SET_VOLTAGE; + + platform_set_drvdata(pdev, ab); + + /* all: Disable phy when called from set_host and set_peripheral */ + INIT_WORK(&ab->phy_dis_work, ab8500_usb_phy_disable_work); + + err = ab8500_usb_regulator_get(ab); + if (err) + return err; + + ab->sysclk = devm_clk_get(ab->dev, "sysclk"); + if (IS_ERR(ab->sysclk)) { + dev_err(ab->dev, "Could not get sysclk.\n"); + return PTR_ERR(ab->sysclk); + } + + err = ab8500_usb_irq_setup(pdev, ab); + if (err < 0) + return err; + + err = usb_add_phy(&ab->phy, USB_PHY_TYPE_USB2); + if (err) { + dev_err(&pdev->dev, "Can't register transceiver\n"); + return err; + } + + if (is_ab8500(ab->ab8500) && !is_ab8500_2p0_or_earlier(ab->ab8500)) + /* Phy tuning values for AB8500 > v2.0 */ + ab8500_usb_set_ab8500_tuning_values(ab); + else if (is_ab8505(ab->ab8500)) + /* Phy tuning values for AB8505 */ + ab8500_usb_set_ab8505_tuning_values(ab); + + /* Needed to enable ID detection. */ + ab8500_usb_wd_workaround(ab); + + /* + * This is required for usb-link-status to work properly when a + * cable is connected at boot time. + */ + ab8500_usb_restart_phy(ab); + + abx500_usb_link_status_update(ab); + + dev_info(&pdev->dev, "revision 0x%2x driver initialized\n", rev); + + return 0; +} + +static int ab8500_usb_remove(struct platform_device *pdev) +{ + struct ab8500_usb *ab = platform_get_drvdata(pdev); + + cancel_work_sync(&ab->phy_dis_work); + + usb_remove_phy(&ab->phy); + + if (ab->mode == USB_HOST) + ab8500_usb_host_phy_dis(ab); + else if (ab->mode == USB_PERIPHERAL) + ab8500_usb_peri_phy_dis(ab); + + return 0; +} + +static const struct platform_device_id ab8500_usb_devtype[] = { + { .name = "ab8500-usb", }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(platform, ab8500_usb_devtype); + +static struct platform_driver ab8500_usb_driver = { + .probe = ab8500_usb_probe, + .remove = ab8500_usb_remove, + .id_table = ab8500_usb_devtype, + .driver = { + .name = "abx5x0-usb", + }, +}; + +static int __init ab8500_usb_init(void) +{ + return platform_driver_register(&ab8500_usb_driver); +} +subsys_initcall(ab8500_usb_init); + +static void __exit ab8500_usb_exit(void) +{ + platform_driver_unregister(&ab8500_usb_driver); +} +module_exit(ab8500_usb_exit); + +MODULE_AUTHOR("ST-Ericsson AB"); +MODULE_DESCRIPTION("AB8500 family usb transceiver driver"); +MODULE_LICENSE("GPL"); |