diff options
Diffstat (limited to 'kernel/irq/manage.c')
| -rw-r--r-- | kernel/irq/manage.c | 2934 |
1 files changed, 2934 insertions, 0 deletions
diff --git a/kernel/irq/manage.c b/kernel/irq/manage.c new file mode 100644 index 000000000..40fe7806c --- /dev/null +++ b/kernel/irq/manage.c @@ -0,0 +1,2934 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Copyright (C) 1992, 1998-2006 Linus Torvalds, Ingo Molnar + * Copyright (C) 2005-2006 Thomas Gleixner + * + * This file contains driver APIs to the irq subsystem. + */ + +#define pr_fmt(fmt) "genirq: " fmt + +#include <linux/irq.h> +#include <linux/kthread.h> +#include <linux/module.h> +#include <linux/random.h> +#include <linux/interrupt.h> +#include <linux/irqdomain.h> +#include <linux/slab.h> +#include <linux/sched.h> +#include <linux/sched/rt.h> +#include <linux/sched/task.h> +#include <linux/sched/isolation.h> +#include <uapi/linux/sched/types.h> +#include <linux/task_work.h> + +#include "internals.h" + +#if defined(CONFIG_IRQ_FORCED_THREADING) && !defined(CONFIG_PREEMPT_RT) +DEFINE_STATIC_KEY_FALSE(force_irqthreads_key); + +static int __init setup_forced_irqthreads(char *arg) +{ + static_branch_enable(&force_irqthreads_key); + return 0; +} +early_param("threadirqs", setup_forced_irqthreads); +#endif + +static void __synchronize_hardirq(struct irq_desc *desc, bool sync_chip) +{ + struct irq_data *irqd = irq_desc_get_irq_data(desc); + bool inprogress; + + do { + unsigned long flags; + + /* + * Wait until we're out of the critical section. This might + * give the wrong answer due to the lack of memory barriers. + */ + while (irqd_irq_inprogress(&desc->irq_data)) + cpu_relax(); + + /* Ok, that indicated we're done: double-check carefully. */ + raw_spin_lock_irqsave(&desc->lock, flags); + inprogress = irqd_irq_inprogress(&desc->irq_data); + + /* + * If requested and supported, check at the chip whether it + * is in flight at the hardware level, i.e. already pending + * in a CPU and waiting for service and acknowledge. + */ + if (!inprogress && sync_chip) { + /* + * Ignore the return code. inprogress is only updated + * when the chip supports it. + */ + __irq_get_irqchip_state(irqd, IRQCHIP_STATE_ACTIVE, + &inprogress); + } + raw_spin_unlock_irqrestore(&desc->lock, flags); + + /* Oops, that failed? */ + } while (inprogress); +} + +/** + * synchronize_hardirq - wait for pending hard IRQ handlers (on other CPUs) + * @irq: interrupt number to wait for + * + * This function waits for any pending hard IRQ handlers for this + * interrupt to complete before returning. If you use this + * function while holding a resource the IRQ handler may need you + * will deadlock. It does not take associated threaded handlers + * into account. + * + * Do not use this for shutdown scenarios where you must be sure + * that all parts (hardirq and threaded handler) have completed. + * + * Returns: false if a threaded handler is active. + * + * This function may be called - with care - from IRQ context. + * + * It does not check whether there is an interrupt in flight at the + * hardware level, but not serviced yet, as this might deadlock when + * called with interrupts disabled and the target CPU of the interrupt + * is the current CPU. + */ +bool synchronize_hardirq(unsigned int irq) +{ + struct irq_desc *desc = irq_to_desc(irq); + + if (desc) { + __synchronize_hardirq(desc, false); + return !atomic_read(&desc->threads_active); + } + + return true; +} +EXPORT_SYMBOL(synchronize_hardirq); + +/** + * synchronize_irq - wait for pending IRQ handlers (on other CPUs) + * @irq: interrupt number to wait for + * + * This function waits for any pending IRQ handlers for this interrupt + * to complete before returning. If you use this function while + * holding a resource the IRQ handler may need you will deadlock. + * + * Can only be called from preemptible code as it might sleep when + * an interrupt thread is associated to @irq. + * + * It optionally makes sure (when the irq chip supports that method) + * that the interrupt is not pending in any CPU and waiting for + * service. + */ +void synchronize_irq(unsigned int irq) +{ + struct irq_desc *desc = irq_to_desc(irq); + + if (desc) { + __synchronize_hardirq(desc, true); + /* + * We made sure that no hardirq handler is + * running. Now verify that no threaded handlers are + * active. + */ + wait_event(desc->wait_for_threads, + !atomic_read(&desc->threads_active)); + } +} +EXPORT_SYMBOL(synchronize_irq); + +#ifdef CONFIG_SMP +cpumask_var_t irq_default_affinity; + +static bool __irq_can_set_affinity(struct irq_desc *desc) +{ + if (!desc || !irqd_can_balance(&desc->irq_data) || + !desc->irq_data.chip || !desc->irq_data.chip->irq_set_affinity) + return false; + return true; +} + +/** + * irq_can_set_affinity - Check if the affinity of a given irq can be set + * @irq: Interrupt to check + * + */ +int irq_can_set_affinity(unsigned int irq) +{ + return __irq_can_set_affinity(irq_to_desc(irq)); +} + +/** + * irq_can_set_affinity_usr - Check if affinity of a irq can be set from user space + * @irq: Interrupt to check + * + * Like irq_can_set_affinity() above, but additionally checks for the + * AFFINITY_MANAGED flag. + */ +bool irq_can_set_affinity_usr(unsigned int irq) +{ + struct irq_desc *desc = irq_to_desc(irq); + + return __irq_can_set_affinity(desc) && + !irqd_affinity_is_managed(&desc->irq_data); +} + +/** + * irq_set_thread_affinity - Notify irq threads to adjust affinity + * @desc: irq descriptor which has affinity changed + * + * We just set IRQTF_AFFINITY and delegate the affinity setting + * to the interrupt thread itself. We can not call + * set_cpus_allowed_ptr() here as we hold desc->lock and this + * code can be called from hard interrupt context. + */ +void irq_set_thread_affinity(struct irq_desc *desc) +{ + struct irqaction *action; + + for_each_action_of_desc(desc, action) + if (action->thread) + set_bit(IRQTF_AFFINITY, &action->thread_flags); +} + +#ifdef CONFIG_GENERIC_IRQ_EFFECTIVE_AFF_MASK +static void irq_validate_effective_affinity(struct irq_data *data) +{ + const struct cpumask *m = irq_data_get_effective_affinity_mask(data); + struct irq_chip *chip = irq_data_get_irq_chip(data); + + if (!cpumask_empty(m)) + return; + pr_warn_once("irq_chip %s did not update eff. affinity mask of irq %u\n", + chip->name, data->irq); +} +#else +static inline void irq_validate_effective_affinity(struct irq_data *data) { } +#endif + +int irq_do_set_affinity(struct irq_data *data, const struct cpumask *mask, + bool force) +{ + struct irq_desc *desc = irq_data_to_desc(data); + struct irq_chip *chip = irq_data_get_irq_chip(data); + const struct cpumask *prog_mask; + int ret; + + static DEFINE_RAW_SPINLOCK(tmp_mask_lock); + static struct cpumask tmp_mask; + + if (!chip || !chip->irq_set_affinity) + return -EINVAL; + + raw_spin_lock(&tmp_mask_lock); + /* + * If this is a managed interrupt and housekeeping is enabled on + * it check whether the requested affinity mask intersects with + * a housekeeping CPU. If so, then remove the isolated CPUs from + * the mask and just keep the housekeeping CPU(s). This prevents + * the affinity setter from routing the interrupt to an isolated + * CPU to avoid that I/O submitted from a housekeeping CPU causes + * interrupts on an isolated one. + * + * If the masks do not intersect or include online CPU(s) then + * keep the requested mask. The isolated target CPUs are only + * receiving interrupts when the I/O operation was submitted + * directly from them. + * + * If all housekeeping CPUs in the affinity mask are offline, the + * interrupt will be migrated by the CPU hotplug code once a + * housekeeping CPU which belongs to the affinity mask comes + * online. + */ + if (irqd_affinity_is_managed(data) && + housekeeping_enabled(HK_TYPE_MANAGED_IRQ)) { + const struct cpumask *hk_mask; + + hk_mask = housekeeping_cpumask(HK_TYPE_MANAGED_IRQ); + + cpumask_and(&tmp_mask, mask, hk_mask); + if (!cpumask_intersects(&tmp_mask, cpu_online_mask)) + prog_mask = mask; + else + prog_mask = &tmp_mask; + } else { + prog_mask = mask; + } + + /* + * Make sure we only provide online CPUs to the irqchip, + * unless we are being asked to force the affinity (in which + * case we do as we are told). + */ + cpumask_and(&tmp_mask, prog_mask, cpu_online_mask); + if (!force && !cpumask_empty(&tmp_mask)) + ret = chip->irq_set_affinity(data, &tmp_mask, force); + else if (force) + ret = chip->irq_set_affinity(data, mask, force); + else + ret = -EINVAL; + + raw_spin_unlock(&tmp_mask_lock); + + switch (ret) { + case IRQ_SET_MASK_OK: + case IRQ_SET_MASK_OK_DONE: + cpumask_copy(desc->irq_common_data.affinity, mask); + fallthrough; + case IRQ_SET_MASK_OK_NOCOPY: + irq_validate_effective_affinity(data); + irq_set_thread_affinity(desc); + ret = 0; + } + + return ret; +} + +#ifdef CONFIG_GENERIC_PENDING_IRQ +static inline int irq_set_affinity_pending(struct irq_data *data, + const struct cpumask *dest) +{ + struct irq_desc *desc = irq_data_to_desc(data); + + irqd_set_move_pending(data); + irq_copy_pending(desc, dest); + return 0; +} +#else +static inline int irq_set_affinity_pending(struct irq_data *data, + const struct cpumask *dest) +{ + return -EBUSY; +} +#endif + +static int irq_try_set_affinity(struct irq_data *data, + const struct cpumask *dest, bool force) +{ + int ret = irq_do_set_affinity(data, dest, force); + + /* + * In case that the underlying vector management is busy and the + * architecture supports the generic pending mechanism then utilize + * this to avoid returning an error to user space. + */ + if (ret == -EBUSY && !force) + ret = irq_set_affinity_pending(data, dest); + return ret; +} + +static bool irq_set_affinity_deactivated(struct irq_data *data, + const struct cpumask *mask, bool force) +{ + struct irq_desc *desc = irq_data_to_desc(data); + + /* + * Handle irq chips which can handle affinity only in activated + * state correctly + * + * If the interrupt is not yet activated, just store the affinity + * mask and do not call the chip driver at all. On activation the + * driver has to make sure anyway that the interrupt is in a + * usable state so startup works. + */ + if (!IS_ENABLED(CONFIG_IRQ_DOMAIN_HIERARCHY) || + irqd_is_activated(data) || !irqd_affinity_on_activate(data)) + return false; + + cpumask_copy(desc->irq_common_data.affinity, mask); + irq_data_update_effective_affinity(data, mask); + irqd_set(data, IRQD_AFFINITY_SET); + return true; +} + +int irq_set_affinity_locked(struct irq_data *data, const struct cpumask *mask, + bool force) +{ + struct irq_chip *chip = irq_data_get_irq_chip(data); + struct irq_desc *desc = irq_data_to_desc(data); + int ret = 0; + + if (!chip || !chip->irq_set_affinity) + return -EINVAL; + + if (irq_set_affinity_deactivated(data, mask, force)) + return 0; + + if (irq_can_move_pcntxt(data) && !irqd_is_setaffinity_pending(data)) { + ret = irq_try_set_affinity(data, mask, force); + } else { + irqd_set_move_pending(data); + irq_copy_pending(desc, mask); + } + + if (desc->affinity_notify) { + kref_get(&desc->affinity_notify->kref); + if (!schedule_work(&desc->affinity_notify->work)) { + /* Work was already scheduled, drop our extra ref */ + kref_put(&desc->affinity_notify->kref, + desc->affinity_notify->release); + } + } + irqd_set(data, IRQD_AFFINITY_SET); + + return ret; +} + +/** + * irq_update_affinity_desc - Update affinity management for an interrupt + * @irq: The interrupt number to update + * @affinity: Pointer to the affinity descriptor + * + * This interface can be used to configure the affinity management of + * interrupts which have been allocated already. + * + * There are certain limitations on when it may be used - attempts to use it + * for when the kernel is configured for generic IRQ reservation mode (in + * config GENERIC_IRQ_RESERVATION_MODE) will fail, as it may conflict with + * managed/non-managed interrupt accounting. In addition, attempts to use it on + * an interrupt which is already started or which has already been configured + * as managed will also fail, as these mean invalid init state or double init. + */ +int irq_update_affinity_desc(unsigned int irq, + struct irq_affinity_desc *affinity) +{ + struct irq_desc *desc; + unsigned long flags; + bool activated; + int ret = 0; + + /* + * Supporting this with the reservation scheme used by x86 needs + * some more thought. Fail it for now. + */ + if (IS_ENABLED(CONFIG_GENERIC_IRQ_RESERVATION_MODE)) + return -EOPNOTSUPP; + + desc = irq_get_desc_buslock(irq, &flags, 0); + if (!desc) + return -EINVAL; + + /* Requires the interrupt to be shut down */ + if (irqd_is_started(&desc->irq_data)) { + ret = -EBUSY; + goto out_unlock; + } + + /* Interrupts which are already managed cannot be modified */ + if (irqd_affinity_is_managed(&desc->irq_data)) { + ret = -EBUSY; + goto out_unlock; + } + + /* + * Deactivate the interrupt. That's required to undo + * anything an earlier activation has established. + */ + activated = irqd_is_activated(&desc->irq_data); + if (activated) + irq_domain_deactivate_irq(&desc->irq_data); + + if (affinity->is_managed) { + irqd_set(&desc->irq_data, IRQD_AFFINITY_MANAGED); + irqd_set(&desc->irq_data, IRQD_MANAGED_SHUTDOWN); + } + + cpumask_copy(desc->irq_common_data.affinity, &affinity->mask); + + /* Restore the activation state */ + if (activated) + irq_domain_activate_irq(&desc->irq_data, false); + +out_unlock: + irq_put_desc_busunlock(desc, flags); + return ret; +} + +static int __irq_set_affinity(unsigned int irq, const struct cpumask *mask, + bool force) +{ + struct irq_desc *desc = irq_to_desc(irq); + unsigned long flags; + int ret; + + if (!desc) + return -EINVAL; + + raw_spin_lock_irqsave(&desc->lock, flags); + ret = irq_set_affinity_locked(irq_desc_get_irq_data(desc), mask, force); + raw_spin_unlock_irqrestore(&desc->lock, flags); + return ret; +} + +/** + * irq_set_affinity - Set the irq affinity of a given irq + * @irq: Interrupt to set affinity + * @cpumask: cpumask + * + * Fails if cpumask does not contain an online CPU + */ +int irq_set_affinity(unsigned int irq, const struct cpumask *cpumask) +{ + return __irq_set_affinity(irq, cpumask, false); +} +EXPORT_SYMBOL_GPL(irq_set_affinity); + +/** + * irq_force_affinity - Force the irq affinity of a given irq + * @irq: Interrupt to set affinity + * @cpumask: cpumask + * + * Same as irq_set_affinity, but without checking the mask against + * online cpus. + * + * Solely for low level cpu hotplug code, where we need to make per + * cpu interrupts affine before the cpu becomes online. + */ +int irq_force_affinity(unsigned int irq, const struct cpumask *cpumask) +{ + return __irq_set_affinity(irq, cpumask, true); +} +EXPORT_SYMBOL_GPL(irq_force_affinity); + +int __irq_apply_affinity_hint(unsigned int irq, const struct cpumask *m, + bool setaffinity) +{ + unsigned long flags; + struct irq_desc *desc = irq_get_desc_lock(irq, &flags, IRQ_GET_DESC_CHECK_GLOBAL); + + if (!desc) + return -EINVAL; + desc->affinity_hint = m; + irq_put_desc_unlock(desc, flags); + if (m && setaffinity) + __irq_set_affinity(irq, m, false); + return 0; +} +EXPORT_SYMBOL_GPL(__irq_apply_affinity_hint); + +static void irq_affinity_notify(struct work_struct *work) +{ + struct irq_affinity_notify *notify = + container_of(work, struct irq_affinity_notify, work); + struct irq_desc *desc = irq_to_desc(notify->irq); + cpumask_var_t cpumask; + unsigned long flags; + + if (!desc || !alloc_cpumask_var(&cpumask, GFP_KERNEL)) + goto out; + + raw_spin_lock_irqsave(&desc->lock, flags); + if (irq_move_pending(&desc->irq_data)) + irq_get_pending(cpumask, desc); + else + cpumask_copy(cpumask, desc->irq_common_data.affinity); + raw_spin_unlock_irqrestore(&desc->lock, flags); + + notify->notify(notify, cpumask); + + free_cpumask_var(cpumask); +out: + kref_put(¬ify->kref, notify->release); +} + +/** + * irq_set_affinity_notifier - control notification of IRQ affinity changes + * @irq: Interrupt for which to enable/disable notification + * @notify: Context for notification, or %NULL to disable + * notification. Function pointers must be initialised; + * the other fields will be initialised by this function. + * + * Must be called in process context. Notification may only be enabled + * after the IRQ is allocated and must be disabled before the IRQ is + * freed using free_irq(). + */ +int +irq_set_affinity_notifier(unsigned int irq, struct irq_affinity_notify *notify) +{ + struct irq_desc *desc = irq_to_desc(irq); + struct irq_affinity_notify *old_notify; + unsigned long flags; + + /* The release function is promised process context */ + might_sleep(); + + if (!desc || desc->istate & IRQS_NMI) + return -EINVAL; + + /* Complete initialisation of *notify */ + if (notify) { + notify->irq = irq; + kref_init(¬ify->kref); + INIT_WORK(¬ify->work, irq_affinity_notify); + } + + raw_spin_lock_irqsave(&desc->lock, flags); + old_notify = desc->affinity_notify; + desc->affinity_notify = notify; + raw_spin_unlock_irqrestore(&desc->lock, flags); + + if (old_notify) { + if (cancel_work_sync(&old_notify->work)) { + /* Pending work had a ref, put that one too */ + kref_put(&old_notify->kref, old_notify->release); + } + kref_put(&old_notify->kref, old_notify->release); + } + + return 0; +} +EXPORT_SYMBOL_GPL(irq_set_affinity_notifier); + +#ifndef CONFIG_AUTO_IRQ_AFFINITY +/* + * Generic version of the affinity autoselector. + */ +int irq_setup_affinity(struct irq_desc *desc) +{ + struct cpumask *set = irq_default_affinity; + int ret, node = irq_desc_get_node(desc); + static DEFINE_RAW_SPINLOCK(mask_lock); + static struct cpumask mask; + + /* Excludes PER_CPU and NO_BALANCE interrupts */ + if (!__irq_can_set_affinity(desc)) + return 0; + + raw_spin_lock(&mask_lock); + /* + * Preserve the managed affinity setting and a userspace affinity + * setup, but make sure that one of the targets is online. + */ + if (irqd_affinity_is_managed(&desc->irq_data) || + irqd_has_set(&desc->irq_data, IRQD_AFFINITY_SET)) { + if (cpumask_intersects(desc->irq_common_data.affinity, + cpu_online_mask)) + set = desc->irq_common_data.affinity; + else + irqd_clear(&desc->irq_data, IRQD_AFFINITY_SET); + } + + cpumask_and(&mask, cpu_online_mask, set); + if (cpumask_empty(&mask)) + cpumask_copy(&mask, cpu_online_mask); + + if (node != NUMA_NO_NODE) { + const struct cpumask *nodemask = cpumask_of_node(node); + + /* make sure at least one of the cpus in nodemask is online */ + if (cpumask_intersects(&mask, nodemask)) + cpumask_and(&mask, &mask, nodemask); + } + ret = irq_do_set_affinity(&desc->irq_data, &mask, false); + raw_spin_unlock(&mask_lock); + return ret; +} +#else +/* Wrapper for ALPHA specific affinity selector magic */ +int irq_setup_affinity(struct irq_desc *desc) +{ + return irq_select_affinity(irq_desc_get_irq(desc)); +} +#endif /* CONFIG_AUTO_IRQ_AFFINITY */ +#endif /* CONFIG_SMP */ + + +/** + * irq_set_vcpu_affinity - Set vcpu affinity for the interrupt + * @irq: interrupt number to set affinity + * @vcpu_info: vCPU specific data or pointer to a percpu array of vCPU + * specific data for percpu_devid interrupts + * + * This function uses the vCPU specific data to set the vCPU + * affinity for an irq. The vCPU specific data is passed from + * outside, such as KVM. One example code path is as below: + * KVM -> IOMMU -> irq_set_vcpu_affinity(). + */ +int irq_set_vcpu_affinity(unsigned int irq, void *vcpu_info) +{ + unsigned long flags; + struct irq_desc *desc = irq_get_desc_lock(irq, &flags, 0); + struct irq_data *data; + struct irq_chip *chip; + int ret = -ENOSYS; + + if (!desc) + return -EINVAL; + + data = irq_desc_get_irq_data(desc); + do { + chip = irq_data_get_irq_chip(data); + if (chip && chip->irq_set_vcpu_affinity) + break; +#ifdef CONFIG_IRQ_DOMAIN_HIERARCHY + data = data->parent_data; +#else + data = NULL; +#endif + } while (data); + + if (data) + ret = chip->irq_set_vcpu_affinity(data, vcpu_info); + irq_put_desc_unlock(desc, flags); + + return ret; +} +EXPORT_SYMBOL_GPL(irq_set_vcpu_affinity); + +void __disable_irq(struct irq_desc *desc) +{ + if (!desc->depth++) + irq_disable(desc); +} + +static int __disable_irq_nosync(unsigned int irq) +{ + unsigned long flags; + struct irq_desc *desc = irq_get_desc_buslock(irq, &flags, IRQ_GET_DESC_CHECK_GLOBAL); + + if (!desc) + return -EINVAL; + __disable_irq(desc); + irq_put_desc_busunlock(desc, flags); + return 0; +} + +/** + * disable_irq_nosync - disable an irq without waiting + * @irq: Interrupt to disable + * + * Disable the selected interrupt line. Disables and Enables are + * nested. + * Unlike disable_irq(), this function does not ensure existing + * instances of the IRQ handler have completed before returning. + * + * This function may be called from IRQ context. + */ +void disable_irq_nosync(unsigned int irq) +{ + __disable_irq_nosync(irq); +} +EXPORT_SYMBOL(disable_irq_nosync); + +/** + * disable_irq - disable an irq and wait for completion + * @irq: Interrupt to disable + * + * Disable the selected interrupt line. Enables and Disables are + * nested. + * This function waits for any pending IRQ handlers for this interrupt + * to complete before returning. If you use this function while + * holding a resource the IRQ handler may need you will deadlock. + * + * This function may be called - with care - from IRQ context. + */ +void disable_irq(unsigned int irq) +{ + if (!__disable_irq_nosync(irq)) + synchronize_irq(irq); +} +EXPORT_SYMBOL(disable_irq); + +/** + * disable_hardirq - disables an irq and waits for hardirq completion + * @irq: Interrupt to disable + * + * Disable the selected interrupt line. Enables and Disables are + * nested. + * This function waits for any pending hard IRQ handlers for this + * interrupt to complete before returning. If you use this function while + * holding a resource the hard IRQ handler may need you will deadlock. + * + * When used to optimistically disable an interrupt from atomic context + * the return value must be checked. + * + * Returns: false if a threaded handler is active. + * + * This function may be called - with care - from IRQ context. + */ +bool disable_hardirq(unsigned int irq) +{ + if (!__disable_irq_nosync(irq)) + return synchronize_hardirq(irq); + + return false; +} +EXPORT_SYMBOL_GPL(disable_hardirq); + +/** + * disable_nmi_nosync - disable an nmi without waiting + * @irq: Interrupt to disable + * + * Disable the selected interrupt line. Disables and enables are + * nested. + * The interrupt to disable must have been requested through request_nmi. + * Unlike disable_nmi(), this function does not ensure existing + * instances of the IRQ handler have completed before returning. + */ +void disable_nmi_nosync(unsigned int irq) +{ + disable_irq_nosync(irq); +} + +void __enable_irq(struct irq_desc *desc) +{ + switch (desc->depth) { + case 0: + err_out: + WARN(1, KERN_WARNING "Unbalanced enable for IRQ %d\n", + irq_desc_get_irq(desc)); + break; + case 1: { + if (desc->istate & IRQS_SUSPENDED) + goto err_out; + /* Prevent probing on this irq: */ + irq_settings_set_noprobe(desc); + /* + * Call irq_startup() not irq_enable() here because the + * interrupt might be marked NOAUTOEN. So irq_startup() + * needs to be invoked when it gets enabled the first + * time. If it was already started up, then irq_startup() + * will invoke irq_enable() under the hood. + */ + irq_startup(desc, IRQ_RESEND, IRQ_START_FORCE); + break; + } + default: + desc->depth--; + } +} + +/** + * enable_irq - enable handling of an irq + * @irq: Interrupt to enable + * + * Undoes the effect of one call to disable_irq(). If this + * matches the last disable, processing of interrupts on this + * IRQ line is re-enabled. + * + * This function may be called from IRQ context only when + * desc->irq_data.chip->bus_lock and desc->chip->bus_sync_unlock are NULL ! + */ +void enable_irq(unsigned int irq) +{ + unsigned long flags; + struct irq_desc *desc = irq_get_desc_buslock(irq, &flags, IRQ_GET_DESC_CHECK_GLOBAL); + + if (!desc) + return; + if (WARN(!desc->irq_data.chip, + KERN_ERR "enable_irq before setup/request_irq: irq %u\n", irq)) + goto out; + + __enable_irq(desc); +out: + irq_put_desc_busunlock(desc, flags); +} +EXPORT_SYMBOL(enable_irq); + +/** + * enable_nmi - enable handling of an nmi + * @irq: Interrupt to enable + * + * The interrupt to enable must have been requested through request_nmi. + * Undoes the effect of one call to disable_nmi(). If this + * matches the last disable, processing of interrupts on this + * IRQ line is re-enabled. + */ +void enable_nmi(unsigned int irq) +{ + enable_irq(irq); +} + +static int set_irq_wake_real(unsigned int irq, unsigned int on) +{ + struct irq_desc *desc = irq_to_desc(irq); + int ret = -ENXIO; + + if (irq_desc_get_chip(desc)->flags & IRQCHIP_SKIP_SET_WAKE) + return 0; + + if (desc->irq_data.chip->irq_set_wake) + ret = desc->irq_data.chip->irq_set_wake(&desc->irq_data, on); + + return ret; +} + +/** + * irq_set_irq_wake - control irq power management wakeup + * @irq: interrupt to control + * @on: enable/disable power management wakeup + * + * Enable/disable power management wakeup mode, which is + * disabled by default. Enables and disables must match, + * just as they match for non-wakeup mode support. + * + * Wakeup mode lets this IRQ wake the system from sleep + * states like "suspend to RAM". + * + * Note: irq enable/disable state is completely orthogonal + * to the enable/disable state of irq wake. An irq can be + * disabled with disable_irq() and still wake the system as + * long as the irq has wake enabled. If this does not hold, + * then the underlying irq chip and the related driver need + * to be investigated. + */ +int irq_set_irq_wake(unsigned int irq, unsigned int on) +{ + unsigned long flags; + struct irq_desc *desc = irq_get_desc_buslock(irq, &flags, IRQ_GET_DESC_CHECK_GLOBAL); + int ret = 0; + + if (!desc) + return -EINVAL; + + /* Don't use NMIs as wake up interrupts please */ + if (desc->istate & IRQS_NMI) { + ret = -EINVAL; + goto out_unlock; + } + + /* wakeup-capable irqs can be shared between drivers that + * don't need to have the same sleep mode behaviors. + */ + if (on) { + if (desc->wake_depth++ == 0) { + ret = set_irq_wake_real(irq, on); + if (ret) + desc->wake_depth = 0; + else + irqd_set(&desc->irq_data, IRQD_WAKEUP_STATE); + } + } else { + if (desc->wake_depth == 0) { + WARN(1, "Unbalanced IRQ %d wake disable\n", irq); + } else if (--desc->wake_depth == 0) { + ret = set_irq_wake_real(irq, on); + if (ret) + desc->wake_depth = 1; + else + irqd_clear(&desc->irq_data, IRQD_WAKEUP_STATE); + } + } + +out_unlock: + irq_put_desc_busunlock(desc, flags); + return ret; +} +EXPORT_SYMBOL(irq_set_irq_wake); + +/* + * Internal function that tells the architecture code whether a + * particular irq has been exclusively allocated or is available + * for driver use. + */ +int can_request_irq(unsigned int irq, unsigned long irqflags) +{ + unsigned long flags; + struct irq_desc *desc = irq_get_desc_lock(irq, &flags, 0); + int canrequest = 0; + + if (!desc) + return 0; + + if (irq_settings_can_request(desc)) { + if (!desc->action || + irqflags & desc->action->flags & IRQF_SHARED) + canrequest = 1; + } + irq_put_desc_unlock(desc, flags); + return canrequest; +} + +int __irq_set_trigger(struct irq_desc *desc, unsigned long flags) +{ + struct irq_chip *chip = desc->irq_data.chip; + int ret, unmask = 0; + + if (!chip || !chip->irq_set_type) { + /* + * IRQF_TRIGGER_* but the PIC does not support multiple + * flow-types? + */ + pr_debug("No set_type function for IRQ %d (%s)\n", + irq_desc_get_irq(desc), + chip ? (chip->name ? : "unknown") : "unknown"); + return 0; + } + + if (chip->flags & IRQCHIP_SET_TYPE_MASKED) { + if (!irqd_irq_masked(&desc->irq_data)) + mask_irq(desc); + if (!irqd_irq_disabled(&desc->irq_data)) + unmask = 1; + } + + /* Mask all flags except trigger mode */ + flags &= IRQ_TYPE_SENSE_MASK; + ret = chip->irq_set_type(&desc->irq_data, flags); + + switch (ret) { + case IRQ_SET_MASK_OK: + case IRQ_SET_MASK_OK_DONE: + irqd_clear(&desc->irq_data, IRQD_TRIGGER_MASK); + irqd_set(&desc->irq_data, flags); + fallthrough; + + case IRQ_SET_MASK_OK_NOCOPY: + flags = irqd_get_trigger_type(&desc->irq_data); + irq_settings_set_trigger_mask(desc, flags); + irqd_clear(&desc->irq_data, IRQD_LEVEL); + irq_settings_clr_level(desc); + if (flags & IRQ_TYPE_LEVEL_MASK) { + irq_settings_set_level(desc); + irqd_set(&desc->irq_data, IRQD_LEVEL); + } + + ret = 0; + break; + default: + pr_err("Setting trigger mode %lu for irq %u failed (%pS)\n", + flags, irq_desc_get_irq(desc), chip->irq_set_type); + } + if (unmask) + unmask_irq(desc); + return ret; +} + +#ifdef CONFIG_HARDIRQS_SW_RESEND +int irq_set_parent(int irq, int parent_irq) +{ + unsigned long flags; + struct irq_desc *desc = irq_get_desc_lock(irq, &flags, 0); + + if (!desc) + return -EINVAL; + + desc->parent_irq = parent_irq; + + irq_put_desc_unlock(desc, flags); + return 0; +} +EXPORT_SYMBOL_GPL(irq_set_parent); +#endif + +/* + * Default primary interrupt handler for threaded interrupts. Is + * assigned as primary handler when request_threaded_irq is called + * with handler == NULL. Useful for oneshot interrupts. + */ +static irqreturn_t irq_default_primary_handler(int irq, void *dev_id) +{ + return IRQ_WAKE_THREAD; +} + +/* + * Primary handler for nested threaded interrupts. Should never be + * called. + */ +static irqreturn_t irq_nested_primary_handler(int irq, void *dev_id) +{ + WARN(1, "Primary handler called for nested irq %d\n", irq); + return IRQ_NONE; +} + +static irqreturn_t irq_forced_secondary_handler(int irq, void *dev_id) +{ + WARN(1, "Secondary action handler called for irq %d\n", irq); + return IRQ_NONE; +} + +static int irq_wait_for_interrupt(struct irqaction *action) +{ + for (;;) { + set_current_state(TASK_INTERRUPTIBLE); + + if (kthread_should_stop()) { + /* may need to run one last time */ + if (test_and_clear_bit(IRQTF_RUNTHREAD, + &action->thread_flags)) { + __set_current_state(TASK_RUNNING); + return 0; + } + __set_current_state(TASK_RUNNING); + return -1; + } + + if (test_and_clear_bit(IRQTF_RUNTHREAD, + &action->thread_flags)) { + __set_current_state(TASK_RUNNING); + return 0; + } + schedule(); + } +} + +/* + * Oneshot interrupts keep the irq line masked until the threaded + * handler finished. unmask if the interrupt has not been disabled and + * is marked MASKED. + */ +static void irq_finalize_oneshot(struct irq_desc *desc, + struct irqaction *action) +{ + if (!(desc->istate & IRQS_ONESHOT) || + action->handler == irq_forced_secondary_handler) + return; +again: + chip_bus_lock(desc); + raw_spin_lock_irq(&desc->lock); + + /* + * Implausible though it may be we need to protect us against + * the following scenario: + * + * The thread is faster done than the hard interrupt handler + * on the other CPU. If we unmask the irq line then the + * interrupt can come in again and masks the line, leaves due + * to IRQS_INPROGRESS and the irq line is masked forever. + * + * This also serializes the state of shared oneshot handlers + * versus "desc->threads_oneshot |= action->thread_mask;" in + * irq_wake_thread(). See the comment there which explains the + * serialization. + */ + if (unlikely(irqd_irq_inprogress(&desc->irq_data))) { + raw_spin_unlock_irq(&desc->lock); + chip_bus_sync_unlock(desc); + cpu_relax(); + goto again; + } + + /* + * Now check again, whether the thread should run. Otherwise + * we would clear the threads_oneshot bit of this thread which + * was just set. + */ + if (test_bit(IRQTF_RUNTHREAD, &action->thread_flags)) + goto out_unlock; + + desc->threads_oneshot &= ~action->thread_mask; + + if (!desc->threads_oneshot && !irqd_irq_disabled(&desc->irq_data) && + irqd_irq_masked(&desc->irq_data)) + unmask_threaded_irq(desc); + +out_unlock: + raw_spin_unlock_irq(&desc->lock); + chip_bus_sync_unlock(desc); +} + +#ifdef CONFIG_SMP +/* + * Check whether we need to change the affinity of the interrupt thread. + */ +static void +irq_thread_check_affinity(struct irq_desc *desc, struct irqaction *action) +{ + cpumask_var_t mask; + bool valid = true; + + if (!test_and_clear_bit(IRQTF_AFFINITY, &action->thread_flags)) + return; + + /* + * In case we are out of memory we set IRQTF_AFFINITY again and + * try again next time + */ + if (!alloc_cpumask_var(&mask, GFP_KERNEL)) { + set_bit(IRQTF_AFFINITY, &action->thread_flags); + return; + } + + raw_spin_lock_irq(&desc->lock); + /* + * This code is triggered unconditionally. Check the affinity + * mask pointer. For CPU_MASK_OFFSTACK=n this is optimized out. + */ + if (cpumask_available(desc->irq_common_data.affinity)) { + const struct cpumask *m; + + m = irq_data_get_effective_affinity_mask(&desc->irq_data); + cpumask_copy(mask, m); + } else { + valid = false; + } + raw_spin_unlock_irq(&desc->lock); + + if (valid) + set_cpus_allowed_ptr(current, mask); + free_cpumask_var(mask); +} +#else +static inline void +irq_thread_check_affinity(struct irq_desc *desc, struct irqaction *action) { } +#endif + +/* + * Interrupts which are not explicitly requested as threaded + * interrupts rely on the implicit bh/preempt disable of the hard irq + * context. So we need to disable bh here to avoid deadlocks and other + * side effects. + */ +static irqreturn_t +irq_forced_thread_fn(struct irq_desc *desc, struct irqaction *action) +{ + irqreturn_t ret; + + local_bh_disable(); + if (!IS_ENABLED(CONFIG_PREEMPT_RT)) + local_irq_disable(); + ret = action->thread_fn(action->irq, action->dev_id); + if (ret == IRQ_HANDLED) + atomic_inc(&desc->threads_handled); + + irq_finalize_oneshot(desc, action); + if (!IS_ENABLED(CONFIG_PREEMPT_RT)) + local_irq_enable(); + local_bh_enable(); + return ret; +} + +/* + * Interrupts explicitly requested as threaded interrupts want to be + * preemptible - many of them need to sleep and wait for slow busses to + * complete. + */ +static irqreturn_t irq_thread_fn(struct irq_desc *desc, + struct irqaction *action) +{ + irqreturn_t ret; + + ret = action->thread_fn(action->irq, action->dev_id); + if (ret == IRQ_HANDLED) + atomic_inc(&desc->threads_handled); + + irq_finalize_oneshot(desc, action); + return ret; +} + +static void wake_threads_waitq(struct irq_desc *desc) +{ + if (atomic_dec_and_test(&desc->threads_active)) + wake_up(&desc->wait_for_threads); +} + +static void irq_thread_dtor(struct callback_head *unused) +{ + struct task_struct *tsk = current; + struct irq_desc *desc; + struct irqaction *action; + + if (WARN_ON_ONCE(!(current->flags & PF_EXITING))) + return; + + action = kthread_data(tsk); + + pr_err("exiting task \"%s\" (%d) is an active IRQ thread (irq %d)\n", + tsk->comm, tsk->pid, action->irq); + + + desc = irq_to_desc(action->irq); + /* + * If IRQTF_RUNTHREAD is set, we need to decrement + * desc->threads_active and wake possible waiters. + */ + if (test_and_clear_bit(IRQTF_RUNTHREAD, &action->thread_flags)) + wake_threads_waitq(desc); + + /* Prevent a stale desc->threads_oneshot */ + irq_finalize_oneshot(desc, action); +} + +static void irq_wake_secondary(struct irq_desc *desc, struct irqaction *action) +{ + struct irqaction *secondary = action->secondary; + + if (WARN_ON_ONCE(!secondary)) + return; + + raw_spin_lock_irq(&desc->lock); + __irq_wake_thread(desc, secondary); + raw_spin_unlock_irq(&desc->lock); +} + +/* + * Internal function to notify that a interrupt thread is ready. + */ +static void irq_thread_set_ready(struct irq_desc *desc, + struct irqaction *action) +{ + set_bit(IRQTF_READY, &action->thread_flags); + wake_up(&desc->wait_for_threads); +} + +/* + * Internal function to wake up a interrupt thread and wait until it is + * ready. + */ +static void wake_up_and_wait_for_irq_thread_ready(struct irq_desc *desc, + struct irqaction *action) +{ + if (!action || !action->thread) + return; + + wake_up_process(action->thread); + wait_event(desc->wait_for_threads, + test_bit(IRQTF_READY, &action->thread_flags)); +} + +/* + * Interrupt handler thread + */ +static int irq_thread(void *data) +{ + struct callback_head on_exit_work; + struct irqaction *action = data; + struct irq_desc *desc = irq_to_desc(action->irq); + irqreturn_t (*handler_fn)(struct irq_desc *desc, + struct irqaction *action); + + irq_thread_set_ready(desc, action); + + sched_set_fifo(current); + + if (force_irqthreads() && test_bit(IRQTF_FORCED_THREAD, + &action->thread_flags)) + handler_fn = irq_forced_thread_fn; + else + handler_fn = irq_thread_fn; + + init_task_work(&on_exit_work, irq_thread_dtor); + task_work_add(current, &on_exit_work, TWA_NONE); + + irq_thread_check_affinity(desc, action); + + while (!irq_wait_for_interrupt(action)) { + irqreturn_t action_ret; + + irq_thread_check_affinity(desc, action); + + action_ret = handler_fn(desc, action); + if (action_ret == IRQ_WAKE_THREAD) + irq_wake_secondary(desc, action); + + wake_threads_waitq(desc); + } + + /* + * This is the regular exit path. __free_irq() is stopping the + * thread via kthread_stop() after calling + * synchronize_hardirq(). So neither IRQTF_RUNTHREAD nor the + * oneshot mask bit can be set. + */ + task_work_cancel(current, irq_thread_dtor); + return 0; +} + +/** + * irq_wake_thread - wake the irq thread for the action identified by dev_id + * @irq: Interrupt line + * @dev_id: Device identity for which the thread should be woken + * + */ +void irq_wake_thread(unsigned int irq, void *dev_id) +{ + struct irq_desc *desc = irq_to_desc(irq); + struct irqaction *action; + unsigned long flags; + + if (!desc || WARN_ON(irq_settings_is_per_cpu_devid(desc))) + return; + + raw_spin_lock_irqsave(&desc->lock, flags); + for_each_action_of_desc(desc, action) { + if (action->dev_id == dev_id) { + if (action->thread) + __irq_wake_thread(desc, action); + break; + } + } + raw_spin_unlock_irqrestore(&desc->lock, flags); +} +EXPORT_SYMBOL_GPL(irq_wake_thread); + +static int irq_setup_forced_threading(struct irqaction *new) +{ + if (!force_irqthreads()) + return 0; + if (new->flags & (IRQF_NO_THREAD | IRQF_PERCPU | IRQF_ONESHOT)) + return 0; + + /* + * No further action required for interrupts which are requested as + * threaded interrupts already + */ + if (new->handler == irq_default_primary_handler) + return 0; + + new->flags |= IRQF_ONESHOT; + + /* + * Handle the case where we have a real primary handler and a + * thread handler. We force thread them as well by creating a + * secondary action. + */ + if (new->handler && new->thread_fn) { + /* Allocate the secondary action */ + new->secondary = kzalloc(sizeof(struct irqaction), GFP_KERNEL); + if (!new->secondary) + return -ENOMEM; + new->secondary->handler = irq_forced_secondary_handler; + new->secondary->thread_fn = new->thread_fn; + new->secondary->dev_id = new->dev_id; + new->secondary->irq = new->irq; + new->secondary->name = new->name; + } + /* Deal with the primary handler */ + set_bit(IRQTF_FORCED_THREAD, &new->thread_flags); + new->thread_fn = new->handler; + new->handler = irq_default_primary_handler; + return 0; +} + +static int irq_request_resources(struct irq_desc *desc) +{ + struct irq_data *d = &desc->irq_data; + struct irq_chip *c = d->chip; + + return c->irq_request_resources ? c->irq_request_resources(d) : 0; +} + +static void irq_release_resources(struct irq_desc *desc) +{ + struct irq_data *d = &desc->irq_data; + struct irq_chip *c = d->chip; + + if (c->irq_release_resources) + c->irq_release_resources(d); +} + +static bool irq_supports_nmi(struct irq_desc *desc) +{ + struct irq_data *d = irq_desc_get_irq_data(desc); + +#ifdef CONFIG_IRQ_DOMAIN_HIERARCHY + /* Only IRQs directly managed by the root irqchip can be set as NMI */ + if (d->parent_data) + return false; +#endif + /* Don't support NMIs for chips behind a slow bus */ + if (d->chip->irq_bus_lock || d->chip->irq_bus_sync_unlock) + return false; + + return d->chip->flags & IRQCHIP_SUPPORTS_NMI; +} + +static int irq_nmi_setup(struct irq_desc *desc) +{ + struct irq_data *d = irq_desc_get_irq_data(desc); + struct irq_chip *c = d->chip; + + return c->irq_nmi_setup ? c->irq_nmi_setup(d) : -EINVAL; +} + +static void irq_nmi_teardown(struct irq_desc *desc) +{ + struct irq_data *d = irq_desc_get_irq_data(desc); + struct irq_chip *c = d->chip; + + if (c->irq_nmi_teardown) + c->irq_nmi_teardown(d); +} + +static int +setup_irq_thread(struct irqaction *new, unsigned int irq, bool secondary) +{ + struct task_struct *t; + + if (!secondary) { + t = kthread_create(irq_thread, new, "irq/%d-%s", irq, + new->name); + } else { + t = kthread_create(irq_thread, new, "irq/%d-s-%s", irq, + new->name); + } + + if (IS_ERR(t)) + return PTR_ERR(t); + + /* + * We keep the reference to the task struct even if + * the thread dies to avoid that the interrupt code + * references an already freed task_struct. + */ + new->thread = get_task_struct(t); + /* + * Tell the thread to set its affinity. This is + * important for shared interrupt handlers as we do + * not invoke setup_affinity() for the secondary + * handlers as everything is already set up. Even for + * interrupts marked with IRQF_NO_BALANCE this is + * correct as we want the thread to move to the cpu(s) + * on which the requesting code placed the interrupt. + */ + set_bit(IRQTF_AFFINITY, &new->thread_flags); + return 0; +} + +/* + * Internal function to register an irqaction - typically used to + * allocate special interrupts that are part of the architecture. + * + * Locking rules: + * + * desc->request_mutex Provides serialization against a concurrent free_irq() + * chip_bus_lock Provides serialization for slow bus operations + * desc->lock Provides serialization against hard interrupts + * + * chip_bus_lock and desc->lock are sufficient for all other management and + * interrupt related functions. desc->request_mutex solely serializes + * request/free_irq(). + */ +static int +__setup_irq(unsigned int irq, struct irq_desc *desc, struct irqaction *new) +{ + struct irqaction *old, **old_ptr; + unsigned long flags, thread_mask = 0; + int ret, nested, shared = 0; + + if (!desc) + return -EINVAL; + + if (desc->irq_data.chip == &no_irq_chip) + return -ENOSYS; + if (!try_module_get(desc->owner)) + return -ENODEV; + + new->irq = irq; + + /* + * If the trigger type is not specified by the caller, + * then use the default for this interrupt. + */ + if (!(new->flags & IRQF_TRIGGER_MASK)) + new->flags |= irqd_get_trigger_type(&desc->irq_data); + + /* + * Check whether the interrupt nests into another interrupt + * thread. + */ + nested = irq_settings_is_nested_thread(desc); + if (nested) { + if (!new->thread_fn) { + ret = -EINVAL; + goto out_mput; + } + /* + * Replace the primary handler which was provided from + * the driver for non nested interrupt handling by the + * dummy function which warns when called. + */ + new->handler = irq_nested_primary_handler; + } else { + if (irq_settings_can_thread(desc)) { + ret = irq_setup_forced_threading(new); + if (ret) + goto out_mput; + } + } + + /* + * Create a handler thread when a thread function is supplied + * and the interrupt does not nest into another interrupt + * thread. + */ + if (new->thread_fn && !nested) { + ret = setup_irq_thread(new, irq, false); + if (ret) + goto out_mput; + if (new->secondary) { + ret = setup_irq_thread(new->secondary, irq, true); + if (ret) + goto out_thread; + } + } + + /* + * Drivers are often written to work w/o knowledge about the + * underlying irq chip implementation, so a request for a + * threaded irq without a primary hard irq context handler + * requires the ONESHOT flag to be set. Some irq chips like + * MSI based interrupts are per se one shot safe. Check the + * chip flags, so we can avoid the unmask dance at the end of + * the threaded handler for those. + */ + if (desc->irq_data.chip->flags & IRQCHIP_ONESHOT_SAFE) + new->flags &= ~IRQF_ONESHOT; + + /* + * Protects against a concurrent __free_irq() call which might wait + * for synchronize_hardirq() to complete without holding the optional + * chip bus lock and desc->lock. Also protects against handing out + * a recycled oneshot thread_mask bit while it's still in use by + * its previous owner. + */ + mutex_lock(&desc->request_mutex); + + /* + * Acquire bus lock as the irq_request_resources() callback below + * might rely on the serialization or the magic power management + * functions which are abusing the irq_bus_lock() callback, + */ + chip_bus_lock(desc); + + /* First installed action requests resources. */ + if (!desc->action) { + ret = irq_request_resources(desc); + if (ret) { + pr_err("Failed to request resources for %s (irq %d) on irqchip %s\n", + new->name, irq, desc->irq_data.chip->name); + goto out_bus_unlock; + } + } + + /* + * The following block of code has to be executed atomically + * protected against a concurrent interrupt and any of the other + * management calls which are not serialized via + * desc->request_mutex or the optional bus lock. + */ + raw_spin_lock_irqsave(&desc->lock, flags); + old_ptr = &desc->action; + old = *old_ptr; + if (old) { + /* + * Can't share interrupts unless both agree to and are + * the same type (level, edge, polarity). So both flag + * fields must have IRQF_SHARED set and the bits which + * set the trigger type must match. Also all must + * agree on ONESHOT. + * Interrupt lines used for NMIs cannot be shared. + */ + unsigned int oldtype; + + if (desc->istate & IRQS_NMI) { + pr_err("Invalid attempt to share NMI for %s (irq %d) on irqchip %s.\n", + new->name, irq, desc->irq_data.chip->name); + ret = -EINVAL; + goto out_unlock; + } + + /* + * If nobody did set the configuration before, inherit + * the one provided by the requester. + */ + if (irqd_trigger_type_was_set(&desc->irq_data)) { + oldtype = irqd_get_trigger_type(&desc->irq_data); + } else { + oldtype = new->flags & IRQF_TRIGGER_MASK; + irqd_set_trigger_type(&desc->irq_data, oldtype); + } + + if (!((old->flags & new->flags) & IRQF_SHARED) || + (oldtype != (new->flags & IRQF_TRIGGER_MASK)) || + ((old->flags ^ new->flags) & IRQF_ONESHOT)) + goto mismatch; + + /* All handlers must agree on per-cpuness */ + if ((old->flags & IRQF_PERCPU) != + (new->flags & IRQF_PERCPU)) + goto mismatch; + + /* add new interrupt at end of irq queue */ + do { + /* + * Or all existing action->thread_mask bits, + * so we can find the next zero bit for this + * new action. + */ + thread_mask |= old->thread_mask; + old_ptr = &old->next; + old = *old_ptr; + } while (old); + shared = 1; + } + + /* + * Setup the thread mask for this irqaction for ONESHOT. For + * !ONESHOT irqs the thread mask is 0 so we can avoid a + * conditional in irq_wake_thread(). + */ + if (new->flags & IRQF_ONESHOT) { + /* + * Unlikely to have 32 resp 64 irqs sharing one line, + * but who knows. + */ + if (thread_mask == ~0UL) { + ret = -EBUSY; + goto out_unlock; + } + /* + * The thread_mask for the action is or'ed to + * desc->thread_active to indicate that the + * IRQF_ONESHOT thread handler has been woken, but not + * yet finished. The bit is cleared when a thread + * completes. When all threads of a shared interrupt + * line have completed desc->threads_active becomes + * zero and the interrupt line is unmasked. See + * handle.c:irq_wake_thread() for further information. + * + * If no thread is woken by primary (hard irq context) + * interrupt handlers, then desc->threads_active is + * also checked for zero to unmask the irq line in the + * affected hard irq flow handlers + * (handle_[fasteoi|level]_irq). + * + * The new action gets the first zero bit of + * thread_mask assigned. See the loop above which or's + * all existing action->thread_mask bits. + */ + new->thread_mask = 1UL << ffz(thread_mask); + + } else if (new->handler == irq_default_primary_handler && + !(desc->irq_data.chip->flags & IRQCHIP_ONESHOT_SAFE)) { + /* + * The interrupt was requested with handler = NULL, so + * we use the default primary handler for it. But it + * does not have the oneshot flag set. In combination + * with level interrupts this is deadly, because the + * default primary handler just wakes the thread, then + * the irq lines is reenabled, but the device still + * has the level irq asserted. Rinse and repeat.... + * + * While this works for edge type interrupts, we play + * it safe and reject unconditionally because we can't + * say for sure which type this interrupt really + * has. The type flags are unreliable as the + * underlying chip implementation can override them. + */ + pr_err("Threaded irq requested with handler=NULL and !ONESHOT for %s (irq %d)\n", + new->name, irq); + ret = -EINVAL; + goto out_unlock; + } + + if (!shared) { + /* Setup the type (level, edge polarity) if configured: */ + if (new->flags & IRQF_TRIGGER_MASK) { + ret = __irq_set_trigger(desc, + new->flags & IRQF_TRIGGER_MASK); + + if (ret) + goto out_unlock; + } + + /* + * Activate the interrupt. That activation must happen + * independently of IRQ_NOAUTOEN. request_irq() can fail + * and the callers are supposed to handle + * that. enable_irq() of an interrupt requested with + * IRQ_NOAUTOEN is not supposed to fail. The activation + * keeps it in shutdown mode, it merily associates + * resources if necessary and if that's not possible it + * fails. Interrupts which are in managed shutdown mode + * will simply ignore that activation request. + */ + ret = irq_activate(desc); + if (ret) + goto out_unlock; + + desc->istate &= ~(IRQS_AUTODETECT | IRQS_SPURIOUS_DISABLED | \ + IRQS_ONESHOT | IRQS_WAITING); + irqd_clear(&desc->irq_data, IRQD_IRQ_INPROGRESS); + + if (new->flags & IRQF_PERCPU) { + irqd_set(&desc->irq_data, IRQD_PER_CPU); + irq_settings_set_per_cpu(desc); + if (new->flags & IRQF_NO_DEBUG) + irq_settings_set_no_debug(desc); + } + + if (noirqdebug) + irq_settings_set_no_debug(desc); + + if (new->flags & IRQF_ONESHOT) + desc->istate |= IRQS_ONESHOT; + + /* Exclude IRQ from balancing if requested */ + if (new->flags & IRQF_NOBALANCING) { + irq_settings_set_no_balancing(desc); + irqd_set(&desc->irq_data, IRQD_NO_BALANCING); + } + + if (!(new->flags & IRQF_NO_AUTOEN) && + irq_settings_can_autoenable(desc)) { + irq_startup(desc, IRQ_RESEND, IRQ_START_COND); + } else { + /* + * Shared interrupts do not go well with disabling + * auto enable. The sharing interrupt might request + * it while it's still disabled and then wait for + * interrupts forever. + */ + WARN_ON_ONCE(new->flags & IRQF_SHARED); + /* Undo nested disables: */ + desc->depth = 1; + } + + } else if (new->flags & IRQF_TRIGGER_MASK) { + unsigned int nmsk = new->flags & IRQF_TRIGGER_MASK; + unsigned int omsk = irqd_get_trigger_type(&desc->irq_data); + + if (nmsk != omsk) + /* hope the handler works with current trigger mode */ + pr_warn("irq %d uses trigger mode %u; requested %u\n", + irq, omsk, nmsk); + } + + *old_ptr = new; + + irq_pm_install_action(desc, new); + + /* Reset broken irq detection when installing new handler */ + desc->irq_count = 0; + desc->irqs_unhandled = 0; + + /* + * Check whether we disabled the irq via the spurious handler + * before. Reenable it and give it another chance. + */ + if (shared && (desc->istate & IRQS_SPURIOUS_DISABLED)) { + desc->istate &= ~IRQS_SPURIOUS_DISABLED; + __enable_irq(desc); + } + + raw_spin_unlock_irqrestore(&desc->lock, flags); + chip_bus_sync_unlock(desc); + mutex_unlock(&desc->request_mutex); + + irq_setup_timings(desc, new); + + wake_up_and_wait_for_irq_thread_ready(desc, new); + wake_up_and_wait_for_irq_thread_ready(desc, new->secondary); + + register_irq_proc(irq, desc); + new->dir = NULL; + register_handler_proc(irq, new); + return 0; + +mismatch: + if (!(new->flags & IRQF_PROBE_SHARED)) { + pr_err("Flags mismatch irq %d. %08x (%s) vs. %08x (%s)\n", + irq, new->flags, new->name, old->flags, old->name); +#ifdef CONFIG_DEBUG_SHIRQ + dump_stack(); +#endif + } + ret = -EBUSY; + +out_unlock: + raw_spin_unlock_irqrestore(&desc->lock, flags); + + if (!desc->action) + irq_release_resources(desc); +out_bus_unlock: + chip_bus_sync_unlock(desc); + mutex_unlock(&desc->request_mutex); + +out_thread: + if (new->thread) { + struct task_struct *t = new->thread; + + new->thread = NULL; + kthread_stop(t); + put_task_struct(t); + } + if (new->secondary && new->secondary->thread) { + struct task_struct *t = new->secondary->thread; + + new->secondary->thread = NULL; + kthread_stop(t); + put_task_struct(t); + } +out_mput: + module_put(desc->owner); + return ret; +} + +/* + * Internal function to unregister an irqaction - used to free + * regular and special interrupts that are part of the architecture. + */ +static struct irqaction *__free_irq(struct irq_desc *desc, void *dev_id) +{ + unsigned irq = desc->irq_data.irq; + struct irqaction *action, **action_ptr; + unsigned long flags; + + WARN(in_interrupt(), "Trying to free IRQ %d from IRQ context!\n", irq); + + mutex_lock(&desc->request_mutex); + chip_bus_lock(desc); + raw_spin_lock_irqsave(&desc->lock, flags); + + /* + * There can be multiple actions per IRQ descriptor, find the right + * one based on the dev_id: + */ + action_ptr = &desc->action; + for (;;) { + action = *action_ptr; + + if (!action) { + WARN(1, "Trying to free already-free IRQ %d\n", irq); + raw_spin_unlock_irqrestore(&desc->lock, flags); + chip_bus_sync_unlock(desc); + mutex_unlock(&desc->request_mutex); + return NULL; + } + + if (action->dev_id == dev_id) + break; + action_ptr = &action->next; + } + + /* Found it - now remove it from the list of entries: */ + *action_ptr = action->next; + + irq_pm_remove_action(desc, action); + + /* If this was the last handler, shut down the IRQ line: */ + if (!desc->action) { + irq_settings_clr_disable_unlazy(desc); + /* Only shutdown. Deactivate after synchronize_hardirq() */ + irq_shutdown(desc); + } + +#ifdef CONFIG_SMP + /* make sure affinity_hint is cleaned up */ + if (WARN_ON_ONCE(desc->affinity_hint)) + desc->affinity_hint = NULL; +#endif + + raw_spin_unlock_irqrestore(&desc->lock, flags); + /* + * Drop bus_lock here so the changes which were done in the chip + * callbacks above are synced out to the irq chips which hang + * behind a slow bus (I2C, SPI) before calling synchronize_hardirq(). + * + * Aside of that the bus_lock can also be taken from the threaded + * handler in irq_finalize_oneshot() which results in a deadlock + * because kthread_stop() would wait forever for the thread to + * complete, which is blocked on the bus lock. + * + * The still held desc->request_mutex() protects against a + * concurrent request_irq() of this irq so the release of resources + * and timing data is properly serialized. + */ + chip_bus_sync_unlock(desc); + + unregister_handler_proc(irq, action); + + /* + * Make sure it's not being used on another CPU and if the chip + * supports it also make sure that there is no (not yet serviced) + * interrupt in flight at the hardware level. + */ + __synchronize_hardirq(desc, true); + +#ifdef CONFIG_DEBUG_SHIRQ + /* + * It's a shared IRQ -- the driver ought to be prepared for an IRQ + * event to happen even now it's being freed, so let's make sure that + * is so by doing an extra call to the handler .... + * + * ( We do this after actually deregistering it, to make sure that a + * 'real' IRQ doesn't run in parallel with our fake. ) + */ + if (action->flags & IRQF_SHARED) { + local_irq_save(flags); + action->handler(irq, dev_id); + local_irq_restore(flags); + } +#endif + + /* + * The action has already been removed above, but the thread writes + * its oneshot mask bit when it completes. Though request_mutex is + * held across this which prevents __setup_irq() from handing out + * the same bit to a newly requested action. + */ + if (action->thread) { + kthread_stop(action->thread); + put_task_struct(action->thread); + if (action->secondary && action->secondary->thread) { + kthread_stop(action->secondary->thread); + put_task_struct(action->secondary->thread); + } + } + + /* Last action releases resources */ + if (!desc->action) { + /* + * Reacquire bus lock as irq_release_resources() might + * require it to deallocate resources over the slow bus. + */ + chip_bus_lock(desc); + /* + * There is no interrupt on the fly anymore. Deactivate it + * completely. + */ + raw_spin_lock_irqsave(&desc->lock, flags); + irq_domain_deactivate_irq(&desc->irq_data); + raw_spin_unlock_irqrestore(&desc->lock, flags); + + irq_release_resources(desc); + chip_bus_sync_unlock(desc); + irq_remove_timings(desc); + } + + mutex_unlock(&desc->request_mutex); + + irq_chip_pm_put(&desc->irq_data); + module_put(desc->owner); + kfree(action->secondary); + return action; +} + +/** + * free_irq - free an interrupt allocated with request_irq + * @irq: Interrupt line to free + * @dev_id: Device identity to free + * + * Remove an interrupt handler. The handler is removed and if the + * interrupt line is no longer in use by any driver it is disabled. + * On a shared IRQ the caller must ensure the interrupt is disabled + * on the card it drives before calling this function. The function + * does not return until any executing interrupts for this IRQ + * have completed. + * + * This function must not be called from interrupt context. + * + * Returns the devname argument passed to request_irq. + */ +const void *free_irq(unsigned int irq, void *dev_id) +{ + struct irq_desc *desc = irq_to_desc(irq); + struct irqaction *action; + const char *devname; + + if (!desc || WARN_ON(irq_settings_is_per_cpu_devid(desc))) + return NULL; + +#ifdef CONFIG_SMP + if (WARN_ON(desc->affinity_notify)) + desc->affinity_notify = NULL; +#endif + + action = __free_irq(desc, dev_id); + + if (!action) + return NULL; + + devname = action->name; + kfree(action); + return devname; +} +EXPORT_SYMBOL(free_irq); + +/* This function must be called with desc->lock held */ +static const void *__cleanup_nmi(unsigned int irq, struct irq_desc *desc) +{ + const char *devname = NULL; + + desc->istate &= ~IRQS_NMI; + + if (!WARN_ON(desc->action == NULL)) { + irq_pm_remove_action(desc, desc->action); + devname = desc->action->name; + unregister_handler_proc(irq, desc->action); + + kfree(desc->action); + desc->action = NULL; + } + + irq_settings_clr_disable_unlazy(desc); + irq_shutdown_and_deactivate(desc); + + irq_release_resources(desc); + + irq_chip_pm_put(&desc->irq_data); + module_put(desc->owner); + + return devname; +} + +const void *free_nmi(unsigned int irq, void *dev_id) +{ + struct irq_desc *desc = irq_to_desc(irq); + unsigned long flags; + const void *devname; + + if (!desc || WARN_ON(!(desc->istate & IRQS_NMI))) + return NULL; + + if (WARN_ON(irq_settings_is_per_cpu_devid(desc))) + return NULL; + + /* NMI still enabled */ + if (WARN_ON(desc->depth == 0)) + disable_nmi_nosync(irq); + + raw_spin_lock_irqsave(&desc->lock, flags); + + irq_nmi_teardown(desc); + devname = __cleanup_nmi(irq, desc); + + raw_spin_unlock_irqrestore(&desc->lock, flags); + + return devname; +} + +/** + * request_threaded_irq - allocate an interrupt line + * @irq: Interrupt line to allocate + * @handler: Function to be called when the IRQ occurs. + * Primary handler for threaded interrupts. + * If handler is NULL and thread_fn != NULL + * the default primary handler is installed. + * @thread_fn: Function called from the irq handler thread + * If NULL, no irq thread is created + * @irqflags: Interrupt type flags + * @devname: An ascii name for the claiming device + * @dev_id: A cookie passed back to the handler function + * + * This call allocates interrupt resources and enables the + * interrupt line and IRQ handling. From the point this + * call is made your handler function may be invoked. Since + * your handler function must clear any interrupt the board + * raises, you must take care both to initialise your hardware + * and to set up the interrupt handler in the right order. + * + * If you want to set up a threaded irq handler for your device + * then you need to supply @handler and @thread_fn. @handler is + * still called in hard interrupt context and has to check + * whether the interrupt originates from the device. If yes it + * needs to disable the interrupt on the device and return + * IRQ_WAKE_THREAD which will wake up the handler thread and run + * @thread_fn. This split handler design is necessary to support + * shared interrupts. + * + * Dev_id must be globally unique. Normally the address of the + * device data structure is used as the cookie. Since the handler + * receives this value it makes sense to use it. + * + * If your interrupt is shared you must pass a non NULL dev_id + * as this is required when freeing the interrupt. + * + * Flags: + * + * IRQF_SHARED Interrupt is shared + * IRQF_TRIGGER_* Specify active edge(s) or level + * IRQF_ONESHOT Run thread_fn with interrupt line masked + */ +int request_threaded_irq(unsigned int irq, irq_handler_t handler, + irq_handler_t thread_fn, unsigned long irqflags, + const char *devname, void *dev_id) +{ + struct irqaction *action; + struct irq_desc *desc; + int retval; + + if (irq == IRQ_NOTCONNECTED) + return -ENOTCONN; + + /* + * Sanity-check: shared interrupts must pass in a real dev-ID, + * otherwise we'll have trouble later trying to figure out + * which interrupt is which (messes up the interrupt freeing + * logic etc). + * + * Also shared interrupts do not go well with disabling auto enable. + * The sharing interrupt might request it while it's still disabled + * and then wait for interrupts forever. + * + * Also IRQF_COND_SUSPEND only makes sense for shared interrupts and + * it cannot be set along with IRQF_NO_SUSPEND. + */ + if (((irqflags & IRQF_SHARED) && !dev_id) || + ((irqflags & IRQF_SHARED) && (irqflags & IRQF_NO_AUTOEN)) || + (!(irqflags & IRQF_SHARED) && (irqflags & IRQF_COND_SUSPEND)) || + ((irqflags & IRQF_NO_SUSPEND) && (irqflags & IRQF_COND_SUSPEND))) + return -EINVAL; + + desc = irq_to_desc(irq); + if (!desc) + return -EINVAL; + + if (!irq_settings_can_request(desc) || + WARN_ON(irq_settings_is_per_cpu_devid(desc))) + return -EINVAL; + + if (!handler) { + if (!thread_fn) + return -EINVAL; + handler = irq_default_primary_handler; + } + + action = kzalloc(sizeof(struct irqaction), GFP_KERNEL); + if (!action) + return -ENOMEM; + + action->handler = handler; + action->thread_fn = thread_fn; + action->flags = irqflags; + action->name = devname; + action->dev_id = dev_id; + + retval = irq_chip_pm_get(&desc->irq_data); + if (retval < 0) { + kfree(action); + return retval; + } + + retval = __setup_irq(irq, desc, action); + + if (retval) { + irq_chip_pm_put(&desc->irq_data); + kfree(action->secondary); + kfree(action); + } + +#ifdef CONFIG_DEBUG_SHIRQ_FIXME + if (!retval && (irqflags & IRQF_SHARED)) { + /* + * It's a shared IRQ -- the driver ought to be prepared for it + * to happen immediately, so let's make sure.... + * We disable the irq to make sure that a 'real' IRQ doesn't + * run in parallel with our fake. + */ + unsigned long flags; + + disable_irq(irq); + local_irq_save(flags); + + handler(irq, dev_id); + + local_irq_restore(flags); + enable_irq(irq); + } +#endif + return retval; +} +EXPORT_SYMBOL(request_threaded_irq); + +/** + * request_any_context_irq - allocate an interrupt line + * @irq: Interrupt line to allocate + * @handler: Function to be called when the IRQ occurs. + * Threaded handler for threaded interrupts. + * @flags: Interrupt type flags + * @name: An ascii name for the claiming device + * @dev_id: A cookie passed back to the handler function + * + * This call allocates interrupt resources and enables the + * interrupt line and IRQ handling. It selects either a + * hardirq or threaded handling method depending on the + * context. + * + * On failure, it returns a negative value. On success, + * it returns either IRQC_IS_HARDIRQ or IRQC_IS_NESTED. + */ +int request_any_context_irq(unsigned int irq, irq_handler_t handler, + unsigned long flags, const char *name, void *dev_id) +{ + struct irq_desc *desc; + int ret; + + if (irq == IRQ_NOTCONNECTED) + return -ENOTCONN; + + desc = irq_to_desc(irq); + if (!desc) + return -EINVAL; + + if (irq_settings_is_nested_thread(desc)) { + ret = request_threaded_irq(irq, NULL, handler, + flags, name, dev_id); + return !ret ? IRQC_IS_NESTED : ret; + } + + ret = request_irq(irq, handler, flags, name, dev_id); + return !ret ? IRQC_IS_HARDIRQ : ret; +} +EXPORT_SYMBOL_GPL(request_any_context_irq); + +/** + * request_nmi - allocate an interrupt line for NMI delivery + * @irq: Interrupt line to allocate + * @handler: Function to be called when the IRQ occurs. + * Threaded handler for threaded interrupts. + * @irqflags: Interrupt type flags + * @name: An ascii name for the claiming device + * @dev_id: A cookie passed back to the handler function + * + * This call allocates interrupt resources and enables the + * interrupt line and IRQ handling. It sets up the IRQ line + * to be handled as an NMI. + * + * An interrupt line delivering NMIs cannot be shared and IRQ handling + * cannot be threaded. + * + * Interrupt lines requested for NMI delivering must produce per cpu + * interrupts and have auto enabling setting disabled. + * + * Dev_id must be globally unique. Normally the address of the + * device data structure is used as the cookie. Since the handler + * receives this value it makes sense to use it. + * + * If the interrupt line cannot be used to deliver NMIs, function + * will fail and return a negative value. + */ +int request_nmi(unsigned int irq, irq_handler_t handler, + unsigned long irqflags, const char *name, void *dev_id) +{ + struct irqaction *action; + struct irq_desc *desc; + unsigned long flags; + int retval; + + if (irq == IRQ_NOTCONNECTED) + return -ENOTCONN; + + /* NMI cannot be shared, used for Polling */ + if (irqflags & (IRQF_SHARED | IRQF_COND_SUSPEND | IRQF_IRQPOLL)) + return -EINVAL; + + if (!(irqflags & IRQF_PERCPU)) + return -EINVAL; + + if (!handler) + return -EINVAL; + + desc = irq_to_desc(irq); + + if (!desc || (irq_settings_can_autoenable(desc) && + !(irqflags & IRQF_NO_AUTOEN)) || + !irq_settings_can_request(desc) || + WARN_ON(irq_settings_is_per_cpu_devid(desc)) || + !irq_supports_nmi(desc)) + return -EINVAL; + + action = kzalloc(sizeof(struct irqaction), GFP_KERNEL); + if (!action) + return -ENOMEM; + + action->handler = handler; + action->flags = irqflags | IRQF_NO_THREAD | IRQF_NOBALANCING; + action->name = name; + action->dev_id = dev_id; + + retval = irq_chip_pm_get(&desc->irq_data); + if (retval < 0) + goto err_out; + + retval = __setup_irq(irq, desc, action); + if (retval) + goto err_irq_setup; + + raw_spin_lock_irqsave(&desc->lock, flags); + + /* Setup NMI state */ + desc->istate |= IRQS_NMI; + retval = irq_nmi_setup(desc); + if (retval) { + __cleanup_nmi(irq, desc); + raw_spin_unlock_irqrestore(&desc->lock, flags); + return -EINVAL; + } + + raw_spin_unlock_irqrestore(&desc->lock, flags); + + return 0; + +err_irq_setup: + irq_chip_pm_put(&desc->irq_data); +err_out: + kfree(action); + + return retval; +} + +void enable_percpu_irq(unsigned int irq, unsigned int type) +{ + unsigned int cpu = smp_processor_id(); + unsigned long flags; + struct irq_desc *desc = irq_get_desc_lock(irq, &flags, IRQ_GET_DESC_CHECK_PERCPU); + + if (!desc) + return; + + /* + * If the trigger type is not specified by the caller, then + * use the default for this interrupt. + */ + type &= IRQ_TYPE_SENSE_MASK; + if (type == IRQ_TYPE_NONE) + type = irqd_get_trigger_type(&desc->irq_data); + + if (type != IRQ_TYPE_NONE) { + int ret; + + ret = __irq_set_trigger(desc, type); + + if (ret) { + WARN(1, "failed to set type for IRQ%d\n", irq); + goto out; + } + } + + irq_percpu_enable(desc, cpu); +out: + irq_put_desc_unlock(desc, flags); +} +EXPORT_SYMBOL_GPL(enable_percpu_irq); + +void enable_percpu_nmi(unsigned int irq, unsigned int type) +{ + enable_percpu_irq(irq, type); +} + +/** + * irq_percpu_is_enabled - Check whether the per cpu irq is enabled + * @irq: Linux irq number to check for + * + * Must be called from a non migratable context. Returns the enable + * state of a per cpu interrupt on the current cpu. + */ +bool irq_percpu_is_enabled(unsigned int irq) +{ + unsigned int cpu = smp_processor_id(); + struct irq_desc *desc; + unsigned long flags; + bool is_enabled; + + desc = irq_get_desc_lock(irq, &flags, IRQ_GET_DESC_CHECK_PERCPU); + if (!desc) + return false; + + is_enabled = cpumask_test_cpu(cpu, desc->percpu_enabled); + irq_put_desc_unlock(desc, flags); + + return is_enabled; +} +EXPORT_SYMBOL_GPL(irq_percpu_is_enabled); + +void disable_percpu_irq(unsigned int irq) +{ + unsigned int cpu = smp_processor_id(); + unsigned long flags; + struct irq_desc *desc = irq_get_desc_lock(irq, &flags, IRQ_GET_DESC_CHECK_PERCPU); + + if (!desc) + return; + + irq_percpu_disable(desc, cpu); + irq_put_desc_unlock(desc, flags); +} +EXPORT_SYMBOL_GPL(disable_percpu_irq); + +void disable_percpu_nmi(unsigned int irq) +{ + disable_percpu_irq(irq); +} + +/* + * Internal function to unregister a percpu irqaction. + */ +static struct irqaction *__free_percpu_irq(unsigned int irq, void __percpu *dev_id) +{ + struct irq_desc *desc = irq_to_desc(irq); + struct irqaction *action; + unsigned long flags; + + WARN(in_interrupt(), "Trying to free IRQ %d from IRQ context!\n", irq); + + if (!desc) + return NULL; + + raw_spin_lock_irqsave(&desc->lock, flags); + + action = desc->action; + if (!action || action->percpu_dev_id != dev_id) { + WARN(1, "Trying to free already-free IRQ %d\n", irq); + goto bad; + } + + if (!cpumask_empty(desc->percpu_enabled)) { + WARN(1, "percpu IRQ %d still enabled on CPU%d!\n", + irq, cpumask_first(desc->percpu_enabled)); + goto bad; + } + + /* Found it - now remove it from the list of entries: */ + desc->action = NULL; + + desc->istate &= ~IRQS_NMI; + + raw_spin_unlock_irqrestore(&desc->lock, flags); + + unregister_handler_proc(irq, action); + + irq_chip_pm_put(&desc->irq_data); + module_put(desc->owner); + return action; + +bad: + raw_spin_unlock_irqrestore(&desc->lock, flags); + return NULL; +} + +/** + * remove_percpu_irq - free a per-cpu interrupt + * @irq: Interrupt line to free + * @act: irqaction for the interrupt + * + * Used to remove interrupts statically setup by the early boot process. + */ +void remove_percpu_irq(unsigned int irq, struct irqaction *act) +{ + struct irq_desc *desc = irq_to_desc(irq); + + if (desc && irq_settings_is_per_cpu_devid(desc)) + __free_percpu_irq(irq, act->percpu_dev_id); +} + +/** + * free_percpu_irq - free an interrupt allocated with request_percpu_irq + * @irq: Interrupt line to free + * @dev_id: Device identity to free + * + * Remove a percpu interrupt handler. The handler is removed, but + * the interrupt line is not disabled. This must be done on each + * CPU before calling this function. The function does not return + * until any executing interrupts for this IRQ have completed. + * + * This function must not be called from interrupt context. + */ +void free_percpu_irq(unsigned int irq, void __percpu *dev_id) +{ + struct irq_desc *desc = irq_to_desc(irq); + + if (!desc || !irq_settings_is_per_cpu_devid(desc)) + return; + + chip_bus_lock(desc); + kfree(__free_percpu_irq(irq, dev_id)); + chip_bus_sync_unlock(desc); +} +EXPORT_SYMBOL_GPL(free_percpu_irq); + +void free_percpu_nmi(unsigned int irq, void __percpu *dev_id) +{ + struct irq_desc *desc = irq_to_desc(irq); + + if (!desc || !irq_settings_is_per_cpu_devid(desc)) + return; + + if (WARN_ON(!(desc->istate & IRQS_NMI))) + return; + + kfree(__free_percpu_irq(irq, dev_id)); +} + +/** + * setup_percpu_irq - setup a per-cpu interrupt + * @irq: Interrupt line to setup + * @act: irqaction for the interrupt + * + * Used to statically setup per-cpu interrupts in the early boot process. + */ +int setup_percpu_irq(unsigned int irq, struct irqaction *act) +{ + struct irq_desc *desc = irq_to_desc(irq); + int retval; + + if (!desc || !irq_settings_is_per_cpu_devid(desc)) + return -EINVAL; + + retval = irq_chip_pm_get(&desc->irq_data); + if (retval < 0) + return retval; + + retval = __setup_irq(irq, desc, act); + + if (retval) + irq_chip_pm_put(&desc->irq_data); + + return retval; +} + +/** + * __request_percpu_irq - allocate a percpu interrupt line + * @irq: Interrupt line to allocate + * @handler: Function to be called when the IRQ occurs. + * @flags: Interrupt type flags (IRQF_TIMER only) + * @devname: An ascii name for the claiming device + * @dev_id: A percpu cookie passed back to the handler function + * + * This call allocates interrupt resources and enables the + * interrupt on the local CPU. If the interrupt is supposed to be + * enabled on other CPUs, it has to be done on each CPU using + * enable_percpu_irq(). + * + * Dev_id must be globally unique. It is a per-cpu variable, and + * the handler gets called with the interrupted CPU's instance of + * that variable. + */ +int __request_percpu_irq(unsigned int irq, irq_handler_t handler, + unsigned long flags, const char *devname, + void __percpu *dev_id) +{ + struct irqaction *action; + struct irq_desc *desc; + int retval; + + if (!dev_id) + return -EINVAL; + + desc = irq_to_desc(irq); + if (!desc || !irq_settings_can_request(desc) || + !irq_settings_is_per_cpu_devid(desc)) + return -EINVAL; + + if (flags && flags != IRQF_TIMER) + return -EINVAL; + + action = kzalloc(sizeof(struct irqaction), GFP_KERNEL); + if (!action) + return -ENOMEM; + + action->handler = handler; + action->flags = flags | IRQF_PERCPU | IRQF_NO_SUSPEND; + action->name = devname; + action->percpu_dev_id = dev_id; + + retval = irq_chip_pm_get(&desc->irq_data); + if (retval < 0) { + kfree(action); + return retval; + } + + retval = __setup_irq(irq, desc, action); + + if (retval) { + irq_chip_pm_put(&desc->irq_data); + kfree(action); + } + + return retval; +} +EXPORT_SYMBOL_GPL(__request_percpu_irq); + +/** + * request_percpu_nmi - allocate a percpu interrupt line for NMI delivery + * @irq: Interrupt line to allocate + * @handler: Function to be called when the IRQ occurs. + * @name: An ascii name for the claiming device + * @dev_id: A percpu cookie passed back to the handler function + * + * This call allocates interrupt resources for a per CPU NMI. Per CPU NMIs + * have to be setup on each CPU by calling prepare_percpu_nmi() before + * being enabled on the same CPU by using enable_percpu_nmi(). + * + * Dev_id must be globally unique. It is a per-cpu variable, and + * the handler gets called with the interrupted CPU's instance of + * that variable. + * + * Interrupt lines requested for NMI delivering should have auto enabling + * setting disabled. + * + * If the interrupt line cannot be used to deliver NMIs, function + * will fail returning a negative value. + */ +int request_percpu_nmi(unsigned int irq, irq_handler_t handler, + const char *name, void __percpu *dev_id) +{ + struct irqaction *action; + struct irq_desc *desc; + unsigned long flags; + int retval; + + if (!handler) + return -EINVAL; + + desc = irq_to_desc(irq); + + if (!desc || !irq_settings_can_request(desc) || + !irq_settings_is_per_cpu_devid(desc) || + irq_settings_can_autoenable(desc) || + !irq_supports_nmi(desc)) + return -EINVAL; + + /* The line cannot already be NMI */ + if (desc->istate & IRQS_NMI) + return -EINVAL; + + action = kzalloc(sizeof(struct irqaction), GFP_KERNEL); + if (!action) + return -ENOMEM; + + action->handler = handler; + action->flags = IRQF_PERCPU | IRQF_NO_SUSPEND | IRQF_NO_THREAD + | IRQF_NOBALANCING; + action->name = name; + action->percpu_dev_id = dev_id; + + retval = irq_chip_pm_get(&desc->irq_data); + if (retval < 0) + goto err_out; + + retval = __setup_irq(irq, desc, action); + if (retval) + goto err_irq_setup; + + raw_spin_lock_irqsave(&desc->lock, flags); + desc->istate |= IRQS_NMI; + raw_spin_unlock_irqrestore(&desc->lock, flags); + + return 0; + +err_irq_setup: + irq_chip_pm_put(&desc->irq_data); +err_out: + kfree(action); + + return retval; +} + +/** + * prepare_percpu_nmi - performs CPU local setup for NMI delivery + * @irq: Interrupt line to prepare for NMI delivery + * + * This call prepares an interrupt line to deliver NMI on the current CPU, + * before that interrupt line gets enabled with enable_percpu_nmi(). + * + * As a CPU local operation, this should be called from non-preemptible + * context. + * + * If the interrupt line cannot be used to deliver NMIs, function + * will fail returning a negative value. + */ +int prepare_percpu_nmi(unsigned int irq) +{ + unsigned long flags; + struct irq_desc *desc; + int ret = 0; + + WARN_ON(preemptible()); + + desc = irq_get_desc_lock(irq, &flags, + IRQ_GET_DESC_CHECK_PERCPU); + if (!desc) + return -EINVAL; + + if (WARN(!(desc->istate & IRQS_NMI), + KERN_ERR "prepare_percpu_nmi called for a non-NMI interrupt: irq %u\n", + irq)) { + ret = -EINVAL; + goto out; + } + + ret = irq_nmi_setup(desc); + if (ret) { + pr_err("Failed to setup NMI delivery: irq %u\n", irq); + goto out; + } + +out: + irq_put_desc_unlock(desc, flags); + return ret; +} + +/** + * teardown_percpu_nmi - undoes NMI setup of IRQ line + * @irq: Interrupt line from which CPU local NMI configuration should be + * removed + * + * This call undoes the setup done by prepare_percpu_nmi(). + * + * IRQ line should not be enabled for the current CPU. + * + * As a CPU local operation, this should be called from non-preemptible + * context. + */ +void teardown_percpu_nmi(unsigned int irq) +{ + unsigned long flags; + struct irq_desc *desc; + + WARN_ON(preemptible()); + + desc = irq_get_desc_lock(irq, &flags, + IRQ_GET_DESC_CHECK_PERCPU); + if (!desc) + return; + + if (WARN_ON(!(desc->istate & IRQS_NMI))) + goto out; + + irq_nmi_teardown(desc); +out: + irq_put_desc_unlock(desc, flags); +} + +int __irq_get_irqchip_state(struct irq_data *data, enum irqchip_irq_state which, + bool *state) +{ + struct irq_chip *chip; + int err = -EINVAL; + + do { + chip = irq_data_get_irq_chip(data); + if (WARN_ON_ONCE(!chip)) + return -ENODEV; + if (chip->irq_get_irqchip_state) + break; +#ifdef CONFIG_IRQ_DOMAIN_HIERARCHY + data = data->parent_data; +#else + data = NULL; +#endif + } while (data); + + if (data) + err = chip->irq_get_irqchip_state(data, which, state); + return err; +} + +/** + * irq_get_irqchip_state - returns the irqchip state of a interrupt. + * @irq: Interrupt line that is forwarded to a VM + * @which: One of IRQCHIP_STATE_* the caller wants to know about + * @state: a pointer to a boolean where the state is to be stored + * + * This call snapshots the internal irqchip state of an + * interrupt, returning into @state the bit corresponding to + * stage @which + * + * This function should be called with preemption disabled if the + * interrupt controller has per-cpu registers. + */ +int irq_get_irqchip_state(unsigned int irq, enum irqchip_irq_state which, + bool *state) +{ + struct irq_desc *desc; + struct irq_data *data; + unsigned long flags; + int err = -EINVAL; + + desc = irq_get_desc_buslock(irq, &flags, 0); + if (!desc) + return err; + + data = irq_desc_get_irq_data(desc); + + err = __irq_get_irqchip_state(data, which, state); + + irq_put_desc_busunlock(desc, flags); + return err; +} +EXPORT_SYMBOL_GPL(irq_get_irqchip_state); + +/** + * irq_set_irqchip_state - set the state of a forwarded interrupt. + * @irq: Interrupt line that is forwarded to a VM + * @which: State to be restored (one of IRQCHIP_STATE_*) + * @val: Value corresponding to @which + * + * This call sets the internal irqchip state of an interrupt, + * depending on the value of @which. + * + * This function should be called with migration disabled if the + * interrupt controller has per-cpu registers. + */ +int irq_set_irqchip_state(unsigned int irq, enum irqchip_irq_state which, + bool val) +{ + struct irq_desc *desc; + struct irq_data *data; + struct irq_chip *chip; + unsigned long flags; + int err = -EINVAL; + + desc = irq_get_desc_buslock(irq, &flags, 0); + if (!desc) + return err; + + data = irq_desc_get_irq_data(desc); + + do { + chip = irq_data_get_irq_chip(data); + if (WARN_ON_ONCE(!chip)) { + err = -ENODEV; + goto out_unlock; + } + if (chip->irq_set_irqchip_state) + break; +#ifdef CONFIG_IRQ_DOMAIN_HIERARCHY + data = data->parent_data; +#else + data = NULL; +#endif + } while (data); + + if (data) + err = chip->irq_set_irqchip_state(data, which, val); + +out_unlock: + irq_put_desc_busunlock(desc, flags); + return err; +} +EXPORT_SYMBOL_GPL(irq_set_irqchip_state); + +/** + * irq_has_action - Check whether an interrupt is requested + * @irq: The linux irq number + * + * Returns: A snapshot of the current state + */ +bool irq_has_action(unsigned int irq) +{ + bool res; + + rcu_read_lock(); + res = irq_desc_has_action(irq_to_desc(irq)); + rcu_read_unlock(); + return res; +} +EXPORT_SYMBOL_GPL(irq_has_action); + +/** + * irq_check_status_bit - Check whether bits in the irq descriptor status are set + * @irq: The linux irq number + * @bitmask: The bitmask to evaluate + * + * Returns: True if one of the bits in @bitmask is set + */ +bool irq_check_status_bit(unsigned int irq, unsigned int bitmask) +{ + struct irq_desc *desc; + bool res = false; + + rcu_read_lock(); + desc = irq_to_desc(irq); + if (desc) + res = !!(desc->status_use_accessors & bitmask); + rcu_read_unlock(); + return res; +} +EXPORT_SYMBOL_GPL(irq_check_status_bit); |