From 2c3c1048746a4622d8c89a29670120dc8fab93c4 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 7 Apr 2024 20:49:45 +0200 Subject: Adding upstream version 6.1.76. Signed-off-by: Daniel Baumann --- .../devicetree/bindings/media/samsung-s5c73m3.txt | 97 ++++++++++++++++++++++ 1 file changed, 97 insertions(+) create mode 100644 Documentation/devicetree/bindings/media/samsung-s5c73m3.txt (limited to 'Documentation/devicetree/bindings/media/samsung-s5c73m3.txt') diff --git a/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt b/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt new file mode 100644 index 000000000..21f31fdf5 --- /dev/null +++ b/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt @@ -0,0 +1,97 @@ +Samsung S5C73M3 8Mp camera ISP +------------------------------ + +The S5C73M3 camera ISP supports MIPI CSI-2 and parallel (ITU-R BT.656) video +data busses. The I2C bus is the main control bus and additionally the SPI bus +is used, mostly for transferring the firmware to and from the device. Two +slave device nodes corresponding to these control bus interfaces are required +and should be placed under respective bus controller nodes. + +I2C slave device node +--------------------- + +Required properties: + +- compatible : "samsung,s5c73m3"; +- reg : I2C slave address of the sensor; +- vdd-int-supply : digital power supply (1.2V); +- vdda-supply : analog power supply (1.2V); +- vdd-reg-supply : regulator input power supply (2.8V); +- vddio-host-supply : host I/O power supply (1.8V to 2.8V); +- vddio-cis-supply : CIS I/O power supply (1.2V to 1.8V); +- vdd-af-supply : lens power supply (2.8V); +- xshutdown-gpios : specifier of GPIO connected to the XSHUTDOWN pin; +- standby-gpios : specifier of GPIO connected to the STANDBY pin; +- clocks : should contain list of phandle and clock specifier pairs + according to common clock bindings for the clocks described + in the clock-names property; +- clock-names : should contain "cis_extclk" entry for the CIS_EXTCLK clock; + +Optional properties: + +- clock-frequency : the frequency at which the "cis_extclk" clock should be + configured to operate, in Hz; if this property is not + specified default 24 MHz value will be used. + +The common video interfaces bindings (see video-interfaces.txt) should be used +to specify link from the S5C73M3 to an external image data receiver. The S5C73M3 +device node should contain one 'port' child node with an 'endpoint' subnode for +this purpose. The data link from a raw image sensor to the S5C73M3 can be +similarly specified, but it is optional since the S5C73M3 ISP and a raw image +sensor are usually inseparable and form a hybrid module. + +Following properties are valid for the endpoint node(s): + +endpoint subnode +---------------- + +- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in + video-interfaces.txt. This sensor doesn't support data lane remapping + and physical lane indexes in subsequent elements of the array should + be only consecutive ascending values. + +SPI device node +--------------- + +Required properties: + +- compatible : "samsung,s5c73m3"; + +For more details see description of the SPI busses bindings +(../spi/spi-bus.txt) and bindings of a specific bus controller. + +Example: + +i2c@138a000000 { + ... + s5c73m3@3c { + compatible = "samsung,s5c73m3"; + reg = <0x3c>; + vdd-int-supply = <&buck9_reg>; + vdda-supply = <&ldo17_reg>; + vdd-reg-supply = <&cam_io_reg>; + vddio-host-supply = <&ldo18_reg>; + vddio-cis-supply = <&ldo9_reg>; + vdd-af-supply = <&cam_af_reg>; + clock-frequency = <24000000>; + clocks = <&clk 0>; + clock-names = "cis_extclk"; + reset-gpios = <&gpf1 3 1>; + standby-gpios = <&gpm0 1 1>; + port { + s5c73m3_ep: endpoint { + remote-endpoint = <&csis0_ep>; + data-lanes = <1 2 3 4>; + }; + }; + }; +}; + +spi@1392000 { + ... + s5c73m3_spi: s5c73m3@0 { + compatible = "samsung,s5c73m3"; + reg = <0>; + ... + }; +}; -- cgit v1.2.3