From 2c3c1048746a4622d8c89a29670120dc8fab93c4 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 7 Apr 2024 20:49:45 +0200 Subject: Adding upstream version 6.1.76. Signed-off-by: Daniel Baumann --- .../devicetree/bindings/net/ti,dp83822.yaml | 82 ++++++++++++++++++++++ 1 file changed, 82 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/ti,dp83822.yaml (limited to 'Documentation/devicetree/bindings/net/ti,dp83822.yaml') diff --git a/Documentation/devicetree/bindings/net/ti,dp83822.yaml b/Documentation/devicetree/bindings/net/ti,dp83822.yaml new file mode 100644 index 000000000..f2489a9c8 --- /dev/null +++ b/Documentation/devicetree/bindings/net/ti,dp83822.yaml @@ -0,0 +1,82 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR BSD-2-Clause) +# Copyright (C) 2020 Texas Instruments Incorporated +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/net/ti,dp83822.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: TI DP83822 ethernet PHY + +maintainers: + - Andrew Davis + +description: | + The DP83822 is a low-power, single-port, 10/100 Mbps Ethernet PHY. It + provides all of the physical layer functions needed to transmit and receive + data over standard, twisted-pair cables or to connect to an external, + fiber-optic transceiver. Additionally, the DP83822 provides flexibility to + connect to a MAC through a standard MII, RMII, or RGMII interface + + Specifications about the Ethernet PHY can be found at: + http://www.ti.com/lit/ds/symlink/dp83822i.pdf + +allOf: + - $ref: "ethernet-phy.yaml#" + +properties: + reg: + maxItems: 1 + + ti,link-loss-low: + type: boolean + description: | + DP83822 PHY in Fiber mode only. + Sets the DP83822 to detect a link drop condition when the signal goes + high. If not set then link drop will occur when the signal goes low. + This property is only applicable if the fiber mode support is strapped + to on. + + ti,fiber-mode: + type: boolean + description: | + DP83822 PHY only. + If present the DP83822 PHY is configured to operate in fiber mode + Fiber mode support can also be strapped. If the strap pin is not set + correctly or not set at all then this boolean can be used to enable it. + If the fiber mode is not strapped then signal detection for the PHY + is disabled. + In fiber mode, auto-negotiation is disabled and the PHY can only work in + 100base-fx (full and half duplex) modes. + + rx-internal-delay-ps: + description: | + DP83822 PHY only. + Setting this property to a non-zero number sets the RX internal delay + for the PHY. The internal delay for the PHY is fixed to 3.5ns relative + to receive data. + + tx-internal-delay-ps: + description: | + DP83822 PHY only. + Setting this property to a non-zero number sets the TX internal delay + for the PHY. The internal delay for the PHY is fixed to 3.5ns relative + to transmit data. + +required: + - reg + +unevaluatedProperties: false + +examples: + - | + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + ethphy0: ethernet-phy@0 { + reg = <0>; + rx-internal-delay-ps = <1>; + tx-internal-delay-ps = <1>; + }; + }; + +... -- cgit v1.2.3