From 2c3c1048746a4622d8c89a29670120dc8fab93c4 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 7 Apr 2024 20:49:45 +0200 Subject: Adding upstream version 6.1.76. Signed-off-by: Daniel Baumann --- .../bindings/net/wireless/qcom,ath10k.txt | 215 +++++++++++++++++++++ 1 file changed, 215 insertions(+) create mode 100644 Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt (limited to 'Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt') diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt new file mode 100644 index 000000000..b61c2d5a0 --- /dev/null +++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt @@ -0,0 +1,215 @@ +* Qualcomm Atheros ath10k wireless devices + +Required properties: +- compatible: Should be one of the following: + * "qcom,ath10k" + * "qcom,ipq4019-wifi" + * "qcom,wcn3990-wifi" + +PCI based devices uses compatible string "qcom,ath10k" and takes calibration +data along with board specific data via "qcom,ath10k-calibration-data". +Rest of the properties are not applicable for PCI based devices. + +AHB based devices (i.e. ipq4019) uses compatible string "qcom,ipq4019-wifi" +and also uses most of the properties defined in this doc (except +"qcom,ath10k-calibration-data"). It uses "qcom,ath10k-pre-calibration-data" +to carry pre calibration data. + +In general, entry "qcom,ath10k-pre-calibration-data" and +"qcom,ath10k-calibration-data" conflict with each other and only one +can be provided per device. + +SNOC based devices (i.e. wcn3990) uses compatible string "qcom,wcn3990-wifi". + +- reg: Address and length of the register set for the device. +- reg-names: Must include the list of following reg names, + "membase" +- interrupts: reference to the list of 17 interrupt numbers for "qcom,ipq4019-wifi" + compatible target. + reference to the list of 12 interrupt numbers for "qcom,wcn3990-wifi" + compatible target. + Must contain interrupt-names property per entry for + "qcom,ath10k", "qcom,ipq4019-wifi" compatible targets. + +- interrupt-names: Must include the entries for MSI interrupt + names ("msi0" to "msi15") and legacy interrupt + name ("legacy") for "qcom,ath10k", "qcom,ipq4019-wifi" + compatible targets. + +Optional properties: +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reseti.txt for details. +- reset-names: Must include the list of following reset names, + "wifi_cpu_init" + "wifi_radio_srif" + "wifi_radio_warm" + "wifi_radio_cold" + "wifi_core_warm" + "wifi_core_cold" +- clocks: List of clock specifiers, must contain an entry for each required + entry in clock-names. +- clock-names: Should contain the clock names "wifi_wcss_cmd", "wifi_wcss_ref", + "wifi_wcss_rtc" for "qcom,ipq4019-wifi" compatible target and + "cxo_ref_clk_pin" and optionally "qdss" for "qcom,wcn3990-wifi" + compatible target. +- qcom,msi_addr: MSI interrupt address. +- qcom,msi_base: Base value to add before writing MSI data into + MSI address register. +- qcom,ath10k-calibration-variant: string to search for in the board-2.bin + variant list with the same bus and device + specific ids +- qcom,ath10k-calibration-data : calibration data + board specific data + as an array, the length can vary between + hw versions. +- qcom,ath10k-pre-calibration-data : pre calibration data as an array, + the length can vary between hw versions. +- -supply: handle to the regulator device tree node + optional "supply-name" are "vdd-0.8-cx-mx", + "vdd-1.8-xo", "vdd-1.3-rfa", "vdd-3.3-ch0", + and "vdd-3.3-ch1". +- memory-region: + Usage: optional + Value type: + Definition: reference to the reserved-memory for the msa region + used by the wifi firmware running in Q6. +- iommus: + Usage: optional + Value type: + Definition: A list of phandle and IOMMU specifier pairs. +- ext-fem-name: + Usage: Optional + Value type: string + Definition: Name of external front end module used. Some valid FEM names + for example: "microsemi-lx5586", "sky85703-11" + and "sky85803" etc. +- qcom,snoc-host-cap-8bit-quirk: + Usage: Optional + Value type: + Definition: Quirk specifying that the firmware expects the 8bit version + of the host capability QMI request +- qcom,xo-cal-data: xo cal offset to be configured in xo trim register. + +- qcom,msa-fixed-perm: Boolean context flag to disable SCM call for statically + mapped msa region. + +- qcom,coexist-support : should contain eithr "0" or "1" to indicate coex + support by the hardware. +- qcom,coexist-gpio-pin : gpio pin number information to support coex + which will be used by wifi firmware. + +* Subnodes +The ath10k wifi node can contain one optional firmware subnode. +Firmware subnode is needed when the platform does not have TustZone. +The firmware subnode must have: + +- iommus: + Usage: required + Value type: + Definition: A list of phandle and IOMMU specifier pairs. + + +Example (to supply PCI based wifi block details): + +In this example, the node is defined as child node of the PCI controller. + +pci { + pcie@0 { + reg = <0 0 0 0 0>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + + wifi@0,0 { + reg = <0 0 0 0 0>; + qcom,ath10k-calibration-data = [ 01 02 03 ... ]; + ext-fem-name = "microsemi-lx5586"; + }; + }; +}; + +Example (to supply ipq4019 SoC wifi block details): + +wifi0: wifi@a000000 { + compatible = "qcom,ipq4019-wifi"; + reg = <0xa000000 0x200000>; + resets = <&gcc WIFI0_CPU_INIT_RESET>, + <&gcc WIFI0_RADIO_SRIF_RESET>, + <&gcc WIFI0_RADIO_WARM_RESET>, + <&gcc WIFI0_RADIO_COLD_RESET>, + <&gcc WIFI0_CORE_WARM_RESET>, + <&gcc WIFI0_CORE_COLD_RESET>; + reset-names = "wifi_cpu_init", + "wifi_radio_srif", + "wifi_radio_warm", + "wifi_radio_cold", + "wifi_core_warm", + "wifi_core_cold"; + clocks = <&gcc GCC_WCSS2G_CLK>, + <&gcc GCC_WCSS2G_REF_CLK>, + <&gcc GCC_WCSS2G_RTC_CLK>; + clock-names = "wifi_wcss_cmd", + "wifi_wcss_ref", + "wifi_wcss_rtc"; + interrupts = <0 0x20 0x1>, + <0 0x21 0x1>, + <0 0x22 0x1>, + <0 0x23 0x1>, + <0 0x24 0x1>, + <0 0x25 0x1>, + <0 0x26 0x1>, + <0 0x27 0x1>, + <0 0x28 0x1>, + <0 0x29 0x1>, + <0 0x2a 0x1>, + <0 0x2b 0x1>, + <0 0x2c 0x1>, + <0 0x2d 0x1>, + <0 0x2e 0x1>, + <0 0x2f 0x1>, + <0 0xa8 0x0>; + interrupt-names = "msi0", "msi1", "msi2", "msi3", + "msi4", "msi5", "msi6", "msi7", + "msi8", "msi9", "msi10", "msi11", + "msi12", "msi13", "msi14", "msi15", + "legacy"; + qcom,msi_addr = <0x0b006040>; + qcom,msi_base = <0x40>; + qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ]; + qcom,coexist-support = <1>; + qcom,coexist-gpio-pin = <0x33>; +}; + +Example (to supply wcn3990 SoC wifi block details): + +wifi@18000000 { + compatible = "qcom,wcn3990-wifi"; + reg = <0x18800000 0x800000>; + reg-names = "membase"; + clocks = <&clock_gcc clk_rf_clk2_pin>; + clock-names = "cxo_ref_clk_pin"; + interrupts = + , + , + , + , + , + , + , + , + , + , + , + ; + vdd-0.8-cx-mx-supply = <&pm8998_l5>; + vdd-1.8-xo-supply = <&vreg_l7a_1p8>; + vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; + vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; + vdd-3.3-ch1-supply = <&vreg_l26a_3p3>; + memory-region = <&wifi_msa_mem>; + iommus = <&apps_smmu 0x0040 0x1>; + qcom,msa-fixed-perm; + wifi-firmware { + iommus = <&apps_iommu 0xc22 0x1>; + }; +}; -- cgit v1.2.3