From 2c3c1048746a4622d8c89a29670120dc8fab93c4 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 7 Apr 2024 20:49:45 +0200 Subject: Adding upstream version 6.1.76. Signed-off-by: Daniel Baumann --- .../bindings/phy/nvidia,tegra124-xusb-padctl.txt | 779 +++++++++++++++++++++ 1 file changed, 779 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt (limited to 'Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt') diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt new file mode 100644 index 000000000..b62397d2b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.txt @@ -0,0 +1,779 @@ +Device tree binding for NVIDIA Tegra XUSB pad controller +======================================================== + +The Tegra XUSB pad controller manages a set of I/O lanes (with differential +signals) which connect directly to pins/pads on the SoC package. Each lane +is controlled by a HW block referred to as a "pad" in the Tegra hardware +documentation. Each such "pad" may control either one or multiple lanes, +and thus contains any logic common to all its lanes. Each lane can be +separately configured and powered up. + +Some of the lanes are high-speed lanes, which can be used for PCIe, SATA or +super-speed USB. Other lanes are for various types of low-speed, full-speed +or high-speed USB (such as UTMI, ULPI and HSIC). The XUSB pad controller +contains a software-configurable mux that sits between the I/O controller +ports (e.g. PCIe) and the lanes. + +In addition to per-lane configuration, USB 3.0 ports may require additional +settings on a per-board basis. + +Pads will be represented as children of the top-level XUSB pad controller +device tree node. Each lane exposed by the pad will be represented by its +own subnode and can be referenced by users of the lane using the standard +PHY bindings, as described by the phy-bindings.txt file in this directory. + +The Tegra hardware documentation refers to the connection between the XUSB +pad controller and the XUSB controller as "ports". This is confusing since +"port" is typically used to denote the physical USB receptacle. The device +tree binding in this document uses the term "port" to refer to the logical +abstraction of the signals that are routed to a USB receptacle (i.e. a PHY +for the USB signal, the VBUS power supply, the USB 2.0 companion port for +USB 3.0 receptacles, ...). + +Required properties: +-------------------- +- compatible: Must be: + - Tegra124: "nvidia,tegra124-xusb-padctl" + - Tegra132: "nvidia,tegra132-xusb-padctl", "nvidia,tegra124-xusb-padctl" + - Tegra210: "nvidia,tegra210-xusb-padctl" + - Tegra186: "nvidia,tegra186-xusb-padctl" + - Tegra194: "nvidia,tegra194-xusb-padctl" +- reg: Physical base address and length of the controller's registers. +- resets: Must contain an entry for each entry in reset-names. +- reset-names: Must include the following entries: + - "padctl" + +For Tegra124: +- avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V. +- avdd-pll-erefe-supply: PLLE reference PLL power supply. Must supply 1.05 V. +- avdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V. +- hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 3.3 V. + +For Tegra210: +- avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V. +- avdd-pll-uerefe-supply: PLLE reference PLL power supply. Must supply 1.05 V. +- dvdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V. +- hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 1.8 V. +- nvidia,pmc: phandle and specifier referring to the Tegra210 PMC node. + +For Tegra186: +- avdd-pll-erefeut-supply: UPHY brick and reference clock as well as UTMI PHY + power supply. Must supply 1.8 V. +- avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply + 3.3 V. +- vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V. +- vddio-hsic-supply: HSIC PHY power supply. Must supply 1.2 V. + +For Tegra194: +- avdd-usb-supply: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must supply + 3.3 V. +- vclamp-usb-supply: Bias rail for USB pad. Must supply 1.8 V. + +Pad nodes: +========== + +A required child node named "pads" contains a list of subnodes, one for each +of the pads exposed by the XUSB pad controller. Each pad may need additional +resources that can be referenced in its pad node. + +The "status" property is used to enable or disable the use of a pad. If set +to "disabled", the pad will not be used on the given board. In order to use +the pad and any of its lanes, this property must be set to "okay". + +For Tegra124 and Tegra132, the following pads exist: usb2, ulpi, hsic, pcie +and sata. No extra resources are required for operation of these pads. + +For Tegra210, the following pads exist: usb2, hsic, pcie and sata. Below is +a description of the properties of each pad. + +UTMI pad: +--------- + +Required properties: +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Must contain the following entries: + - "trk": phandle and specifier referring to the USB2 tracking clock + +HSIC pad: +--------- + +Required properties: +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Must contain the following entries: + - "trk": phandle and specifier referring to the HSIC tracking clock + +PCIe pad: +--------- + +Required properties: +- clocks: Must contain an entry for each entry in clock-names. +- clock-names: Must contain the following entries: + - "pll": phandle and specifier referring to the PLLE +- resets: Must contain an entry for each entry in reset-names. +- reset-names: Must contain the following entries: + - "phy": reset for the PCIe UPHY block + +SATA pad: +--------- + +Required properties: +- resets: Must contain an entry for each entry in reset-names. +- reset-names: Must contain the following entries: + - "phy": reset for the SATA UPHY block + + +PHY nodes: +========== + +Each pad node has a child named "lanes" that contains one or more children of +its own, each representing one of the lanes controlled by the pad. + +Required properties: +-------------------- +- status: Defines the operation status of the PHY. Valid values are: + - "disabled": the PHY is disabled + - "okay": the PHY is enabled +- #phy-cells: Should be 0. Since each lane represents a single PHY, there is + no need for an additional specifier. +- nvidia,function: The output function of the PHY. See below for a list of + valid functions per SoC generation. + +For Tegra124 and Tegra132, the list of valid PHY nodes is given below: +- usb2: usb2-0, usb2-1, usb2-2 + - functions: "snps", "xusb", "uart" +- ulpi: ulpi-0 + - functions: "snps", "xusb" +- hsic: hsic-0, hsic-1 + - functions: "snps", "xusb" +- pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4 + - functions: "pcie", "usb3-ss" +- sata: sata-0 + - functions: "usb3-ss", "sata" + +For Tegra210, the list of valid PHY nodes is given below: +- usb2: usb2-0, usb2-1, usb2-2, usb2-3 + - functions: "snps", "xusb", "uart" +- hsic: hsic-0, hsic-1 + - functions: "snps", "xusb" +- pcie: pcie-0, pcie-1, pcie-2, pcie-3, pcie-4, pcie-5, pcie-6 + - functions: "pcie-x1", "usb3-ss", "pcie-x4" +- sata: sata-0 + - functions: "usb3-ss", "sata" + +For Tegra194, the list of valid PHY nodes is given below: +- usb2: usb2-0, usb2-1, usb2-2, usb2-3 + - functions: "xusb" +- usb3: usb3-0, usb3-1, usb3-2, usb3-3 + - functions: "xusb" + +Port nodes: +=========== + +A required child node named "ports" contains a list of all the ports exposed +by the XUSB pad controller. Per-port configuration is only required for USB. + +USB2 ports: +----------- + +Required properties: +- status: Defines the operation status of the port. Valid values are: + - "disabled": the port is disabled + - "okay": the port is enabled +- mode: A string that determines the mode in which to run the port. Valid + values are: + - "host": for USB host mode + - "device": for USB device mode + - "otg": for USB OTG mode + +Required properties for OTG/Peripheral capable USB2 ports: +- usb-role-switch: Boolean property to indicate that the port support OTG or + peripheral mode. If present, the port supports switching between USB host + and peripheral roles. Connector should be added as subnode. + See usb/usb-conn-gpio.txt. + +Optional properties: +- nvidia,internal: A boolean property whose presence determines that a port + is internal. In the absence of this property the port is considered to be + external. +- vbus-supply: phandle to a regulator supplying the VBUS voltage. + +ULPI ports: +----------- + +Optional properties: +- status: Defines the operation status of the port. Valid values are: + - "disabled": the port is disabled + - "okay": the port is enabled +- nvidia,internal: A boolean property whose presence determines that a port + is internal. In the absence of this property the port is considered to be + external. +- vbus-supply: phandle to a regulator supplying the VBUS voltage. + +HSIC ports: +----------- + +Required properties: +- status: Defines the operation status of the port. Valid values are: + - "disabled": the port is disabled + - "okay": the port is enabled + +Optional properties: +- vbus-supply: phandle to a regulator supplying the VBUS voltage. + +Super-speed USB ports: +---------------------- + +Required properties: +- status: Defines the operation status of the port. Valid values are: + - "disabled": the port is disabled + - "okay": the port is enabled +- nvidia,usb2-companion: A single cell that specifies the physical port number + to map this super-speed USB port to. The range of valid port numbers varies + with the SoC generation: + - 0-2: for Tegra124 and Tegra132 + - 0-3: for Tegra210 + +Optional properties: +- nvidia,internal: A boolean property whose presence determines that a port + is internal. In the absence of this property the port is considered to be + external. + +- maximum-speed: Only for Tegra194. A string property that specifies maximum + supported speed of a usb3 port. Valid values are: + - "super-speed-plus": default, the usb3 port supports USB 3.1 Gen 2 speed. + - "super-speed": the usb3 port supports USB 3.1 Gen 1 speed only. + +For Tegra124 and Tegra132, the XUSB pad controller exposes the following +ports: +- 3x USB2: usb2-0, usb2-1, usb2-2 +- 1x ULPI: ulpi-0 +- 2x HSIC: hsic-0, hsic-1 +- 2x super-speed USB: usb3-0, usb3-1 + +For Tegra210, the XUSB pad controller exposes the following ports: +- 4x USB2: usb2-0, usb2-1, usb2-2, usb2-3 +- 2x HSIC: hsic-0, hsic-1 +- 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3 + +For Tegra194, the XUSB pad controller exposes the following ports: +- 4x USB2: usb2-0, usb2-1, usb2-2, usb2-3 +- 4x super-speed USB: usb3-0, usb3-1, usb3-2, usb3-3 + +Examples: +========= + +Tegra124 and Tegra132: +---------------------- + +SoC include: + + padctl@7009f000 { + /* for Tegra124 */ + compatible = "nvidia,tegra124-xusb-padctl"; + /* for Tegra132 */ + compatible = "nvidia,tegra132-xusb-padctl", + "nvidia,tegra124-xusb-padctl"; + reg = <0x0 0x7009f000 0x0 0x1000>; + resets = <&tegra_car 142>; + reset-names = "padctl"; + + pads { + usb2 { + status = "disabled"; + + lanes { + usb2-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-2 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + ulpi { + status = "disabled"; + + lanes { + ulpi-0 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + hsic { + status = "disabled"; + + lanes { + hsic-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + hsic-1 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + pcie { + status = "disabled"; + + lanes { + pcie-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-2 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-3 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-4 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + sata { + status = "disabled"; + + lanes { + sata-0 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + }; + + ports { + usb2-0 { + status = "disabled"; + }; + + usb2-1 { + status = "disabled"; + }; + + usb2-2 { + status = "disabled"; + }; + + ulpi-0 { + status = "disabled"; + }; + + hsic-0 { + status = "disabled"; + }; + + hsic-1 { + status = "disabled"; + }; + + usb3-0 { + status = "disabled"; + }; + + usb3-1 { + status = "disabled"; + }; + }; + }; + +Board file: + + padctl@7009f000 { + status = "okay"; + + pads { + usb2 { + status = "okay"; + + lanes { + usb2-0 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-1 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-2 { + nvidia,function = "xusb"; + status = "okay"; + }; + }; + }; + + pcie { + status = "okay"; + + lanes { + pcie-0 { + nvidia,function = "usb3-ss"; + status = "okay"; + }; + + pcie-2 { + nvidia,function = "pcie"; + status = "okay"; + }; + + pcie-4 { + nvidia,function = "pcie"; + status = "okay"; + }; + }; + }; + + sata { + status = "okay"; + + lanes { + sata-0 { + nvidia,function = "sata"; + status = "okay"; + }; + }; + }; + }; + + ports { + /* Micro A/B */ + usb2-0 { + status = "okay"; + mode = "otg"; + }; + + /* Mini PCIe */ + usb2-1 { + status = "okay"; + mode = "host"; + }; + + /* USB3 */ + usb2-2 { + status = "okay"; + mode = "host"; + + vbus-supply = <&vdd_usb3_vbus>; + }; + + usb3-0 { + nvidia,port = <2>; + status = "okay"; + }; + }; + }; + +Tegra210: +--------- + +SoC include: + + padctl@7009f000 { + compatible = "nvidia,tegra210-xusb-padctl"; + reg = <0x0 0x7009f000 0x0 0x1000>; + resets = <&tegra_car 142>; + reset-names = "padctl"; + + status = "disabled"; + + pads { + usb2 { + clocks = <&tegra_car TEGRA210_CLK_USB2_TRK>; + clock-names = "trk"; + status = "disabled"; + + lanes { + usb2-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-2 { + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-3 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + hsic { + clocks = <&tegra_car TEGRA210_CLK_HSIC_TRK>; + clock-names = "trk"; + status = "disabled"; + + lanes { + hsic-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + hsic-1 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + pcie { + clocks = <&tegra_car TEGRA210_CLK_PLL_E>; + clock-names = "pll"; + resets = <&tegra_car 205>; + reset-names = "phy"; + status = "disabled"; + + lanes { + pcie-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-2 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-3 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-4 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-5 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-6 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + sata { + clocks = <&tegra_car TEGRA210_CLK_PLL_E>; + clock-names = "pll"; + resets = <&tegra_car 204>; + reset-names = "phy"; + status = "disabled"; + + lanes { + sata-0 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + }; + + ports { + usb2-0 { + status = "disabled"; + }; + + usb2-1 { + status = "disabled"; + }; + + usb2-2 { + status = "disabled"; + }; + + usb2-3 { + status = "disabled"; + }; + + hsic-0 { + status = "disabled"; + }; + + hsic-1 { + status = "disabled"; + }; + + usb3-0 { + status = "disabled"; + }; + + usb3-1 { + status = "disabled"; + }; + + usb3-2 { + status = "disabled"; + }; + + usb3-3 { + status = "disabled"; + }; + }; + }; + +Board file: + + padctl@7009f000 { + status = "okay"; + + pads { + usb2 { + status = "okay"; + + lanes { + usb2-0 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-1 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-2 { + nvidia,function = "xusb"; + status = "okay"; + }; + + usb2-3 { + nvidia,function = "xusb"; + status = "okay"; + }; + }; + }; + + pcie { + status = "okay"; + + lanes { + pcie-0 { + nvidia,function = "pcie-x1"; + status = "okay"; + }; + + pcie-1 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-2 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-3 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-4 { + nvidia,function = "pcie-x4"; + status = "okay"; + }; + + pcie-5 { + nvidia,function = "usb3-ss"; + status = "okay"; + }; + + pcie-6 { + nvidia,function = "usb3-ss"; + status = "okay"; + }; + }; + }; + + sata { + status = "okay"; + + lanes { + sata-0 { + nvidia,function = "sata"; + status = "okay"; + }; + }; + }; + }; + + ports { + usb2-0 { + status = "okay"; + mode = "otg"; + }; + + usb2-1 { + status = "okay"; + vbus-supply = <&vdd_5v0_rtl>; + mode = "host"; + }; + + usb2-2 { + status = "okay"; + vbus-supply = <&vdd_usb_vbus>; + mode = "host"; + }; + + usb2-3 { + status = "okay"; + mode = "host"; + }; + + usb3-0 { + status = "okay"; + nvidia,lanes = "pcie-6"; + nvidia,port = <1>; + }; + + usb3-1 { + status = "okay"; + nvidia,lanes = "pcie-5"; + nvidia,port = <2>; + }; + }; + }; -- cgit v1.2.3