From 2c3c1048746a4622d8c89a29670120dc8fab93c4 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 7 Apr 2024 20:49:45 +0200 Subject: Adding upstream version 6.1.76. Signed-off-by: Daniel Baumann --- .../bindings/pinctrl/fsl,imx27-pinctrl.txt | 121 +++++++++++++++++++++ 1 file changed, 121 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt (limited to 'Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt') diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt new file mode 100644 index 000000000..d1706ea82 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx27-pinctrl.txt @@ -0,0 +1,121 @@ +* Freescale IMX27 IOMUX Controller + +Required properties: +- compatible: "fsl,imx27-iomuxc" + +The iomuxc driver node should define subnodes containing of pinctrl configuration subnodes. + +Required properties for pin configuration node: +- fsl,pins: three integers array, represents a group of pins mux and config + setting. The format is fsl,pins = . + + PIN is an integer between 0 and 0xbf. imx27 has 6 ports with 32 configurable + configurable pins each. PIN is PORT * 32 + PORT_PIN, PORT_PIN is the pin + number on the specific port (between 0 and 31). + + MUX_ID is + function + (direction << 2) + (gpio_oconf << 4) + (gpio_iconfa << 8) + (gpio_iconfb << 10) + + function value is used to select the pin function. + Possible values: + 0 - Primary function + 1 - Alternate function + 2 - GPIO + Registers: GIUS (GPIO In Use), GPR (General Purpose Register) + + direction defines the data direction of the pin. + Possible values: + 0 - Input + 1 - Output + Register: DDIR + + gpio_oconf configures the gpio submodule output signal. This does not + have any effect unless GPIO function is selected. A/B/C_IN are output + signals of function blocks A,B and C. Specific function blocks are + described in the reference manual. + Possible values: + 0 - A_IN + 1 - B_IN + 2 - C_IN + 3 - Data Register + Registers: OCR1, OCR2 + + gpio_iconfa/b configures the gpio submodule input to functionblocks A and + B. GPIO function should be selected if this is configured. + Possible values: + 0 - GPIO_IN + 1 - Interrupt Status Register + 2 - Pulldown + 3 - Pullup + Registers ICONFA1, ICONFA2, ICONFB1 and ICONFB2 + + CONFIG can be 0 or 1, meaning Pullup disable/enable. + + +The iomux controller has gpio child nodes which are embedded in the iomux +control registers. They have to be defined as child nodes of the iomux device +node. If gpio subnodes are defined "#address-cells", "#size-cells" and "ranges" +properties for the iomux device node are required. + +Example: + +iomuxc: iomuxc@10015000 { + compatible = "fsl,imx27-iomuxc"; + reg = <0x10015000 0x600>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gpio1: gpio@10015000 { + ... + }; + + ... + + uart { + pinctrl_uart1: uart-1 { + fsl,pins = < + 0x8c 0x004 0x0 /* UART1_TXD__UART1_TXD */ + 0x8d 0x000 0x0 /* UART1_RXD__UART1_RXD */ + 0x8e 0x004 0x0 /* UART1_CTS__UART1_CTS */ + 0x8f 0x000 0x0 /* UART1_RTS__UART1_RTS */ + >; + }; + + ... + }; +}; + + +For convenience there are macros defined in imx27-pinfunc.h which provide PIN +and MUX_ID. They are structured as MX27_PAD___. The names +are defined in the i.MX27 reference manual. + +The above example using macros: + +iomuxc: iomuxc@10015000 { + compatible = "fsl,imx27-iomuxc"; + reg = <0x10015000 0x600>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gpio1: gpio@10015000 { + ... + }; + + ... + + uart { + pinctrl_uart1: uart-1 { + fsl,pins = < + MX27_PAD_UART1_TXD__UART1_TXD 0x0 + MX27_PAD_UART1_RXD__UART1_RXD 0x0 + MX27_PAD_UART1_CTS__UART1_CTS 0x0 + MX27_PAD_UART1_RTS__UART1_RTS 0x0 + >; + }; + + ... + }; +}; -- cgit v1.2.3