From 2c3c1048746a4622d8c89a29670120dc8fab93c4 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 7 Apr 2024 20:49:45 +0200 Subject: Adding upstream version 6.1.76. Signed-off-by: Daniel Baumann --- Documentation/i2c/slave-testunit-backend.rst | 88 ++++++++++++++++++++++++++++ 1 file changed, 88 insertions(+) create mode 100644 Documentation/i2c/slave-testunit-backend.rst (limited to 'Documentation/i2c/slave-testunit-backend.rst') diff --git a/Documentation/i2c/slave-testunit-backend.rst b/Documentation/i2c/slave-testunit-backend.rst new file mode 100644 index 000000000..ecfc2abec --- /dev/null +++ b/Documentation/i2c/slave-testunit-backend.rst @@ -0,0 +1,88 @@ +.. SPDX-License-Identifier: GPL-2.0 + +================================ +Linux I2C slave testunit backend +================================ + +by Wolfram Sang in 2020 + +This backend can be used to trigger test cases for I2C bus masters which +require a remote device with certain capabilities (and which are usually not so +easy to obtain). Examples include multi-master testing, and SMBus Host Notify +testing. For some tests, the I2C slave controller must be able to switch +between master and slave mode because it needs to send data, too. + +Note that this is a device for testing and debugging. It should not be enabled +in a production build. And while there is some versioning and we try hard to +keep backward compatibility, there is no stable ABI guaranteed! + +Instantiating the device is regular. Example for bus 0, address 0x30: + +# echo "slave-testunit 0x1030" > /sys/bus/i2c/devices/i2c-0/new_device + +After that, you will have a write-only device listening. Reads will just return +an 8-bit version number of the testunit. When writing, the device consists of 4 +8-bit registers and, except for some "partial" commands, all registers must be +written to start a testcase, i.e. you usually write 4 bytes to the device. The +registers are: + +0x00 CMD - which test to trigger +0x01 DATAL - configuration byte 1 for the test +0x02 DATAH - configuration byte 2 for the test +0x03 DELAY - delay in n * 10ms until test is started + +Using 'i2cset' from the i2c-tools package, the generic command looks like: + +# i2cset -y i + +DELAY is a generic parameter which will delay the execution of the test in CMD. +While a command is running (including the delay), new commands will not be +acknowledged. You need to wait until the old one is completed. + +The commands are described in the following section. An invalid command will +result in the transfer not being acknowledged. + +Commands +-------- + +0x00 NOOP (reserved for future use) + +0x01 READ_BYTES (also needs master mode) + DATAL - address to read data from (lower 7 bits, highest bit currently unused) + DATAH - number of bytes to read + +This is useful to test if your bus master driver is handling multi-master +correctly. You can trigger the testunit to read bytes from another device on +the bus. If the bus master under test also wants to access the bus at the same +time, the bus will be busy. Example to read 128 bytes from device 0x50 after +50ms of delay: + +# i2cset -y 0 0x30 0x01 0x50 0x80 0x05 i + +0x02 SMBUS_HOST_NOTIFY (also needs master mode) + DATAL - low byte of the status word to send + DATAH - high byte of the status word to send + +This test will send an SMBUS_HOST_NOTIFY message to the host. Note that the +status word is currently ignored in the Linux Kernel. Example to send a +notification after 10ms: + +# i2cset -y 0 0x30 0x02 0x42 0x64 0x01 i + +0x03 SMBUS_BLOCK_PROC_CALL (partial command) + DATAL - must be '1', i.e. one further byte will be written + DATAH - number of bytes to be sent back + DELAY - not applicable, partial command! + +This test will respond to a block process call as defined by the SMBus +specification. The one data byte written specifies how many bytes will be sent +back in the following read transfer. Note that in this read transfer, the +testunit will prefix the length of the bytes to follow. So, if your host bus +driver emulates SMBus calls like the majority does, it needs to support the +I2C_M_RECV_LEN flag of an i2c_msg. This is a good testcase for it. The returned +data consists of the length first, and then of an array of bytes from length-1 +to 0. Here is an example which emulates i2c_smbus_block_process_call() using +i2ctransfer (you need i2c-tools v4.2 or later): + +# i2ctransfer -y 0 w3@0x30 0x03 0x01 0x10 r? +0x10 0x0f 0x0e 0x0d 0x0c 0x0b 0x0a 0x09 0x08 0x07 0x06 0x05 0x04 0x03 0x02 0x01 0x00 -- cgit v1.2.3