From 2c3c1048746a4622d8c89a29670120dc8fab93c4 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 7 Apr 2024 20:49:45 +0200 Subject: Adding upstream version 6.1.76. Signed-off-by: Daniel Baumann --- Documentation/networking/netconsole.rst | 239 ++++++++++++++++++++++++++++++++ 1 file changed, 239 insertions(+) create mode 100644 Documentation/networking/netconsole.rst (limited to 'Documentation/networking/netconsole.rst') diff --git a/Documentation/networking/netconsole.rst b/Documentation/networking/netconsole.rst new file mode 100644 index 000000000..1f5c4a040 --- /dev/null +++ b/Documentation/networking/netconsole.rst @@ -0,0 +1,239 @@ +.. SPDX-License-Identifier: GPL-2.0 + +========== +Netconsole +========== + + +started by Ingo Molnar , 2001.09.17 + +2.6 port and netpoll api by Matt Mackall , Sep 9 2003 + +IPv6 support by Cong Wang , Jan 1 2013 + +Extended console support by Tejun Heo , May 1 2015 + +Please send bug reports to Matt Mackall +Satyam Sharma , and Cong Wang + +Introduction: +============= + +This module logs kernel printk messages over UDP allowing debugging of +problem where disk logging fails and serial consoles are impractical. + +It can be used either built-in or as a module. As a built-in, +netconsole initializes immediately after NIC cards and will bring up +the specified interface as soon as possible. While this doesn't allow +capture of early kernel panics, it does capture most of the boot +process. + +Sender and receiver configuration: +================================== + +It takes a string configuration parameter "netconsole" in the +following format:: + + netconsole=[+][src-port]@[src-ip]/[],[tgt-port]@/[tgt-macaddr] + + where + + if present, enable extended console support + src-port source for UDP packets (defaults to 6665) + src-ip source IP to use (interface address) + dev network interface (eth0) + tgt-port port for logging agent (6666) + tgt-ip IP address for logging agent + tgt-macaddr ethernet MAC address for logging agent (broadcast) + +Examples:: + + linux netconsole=4444@10.0.0.1/eth1,9353@10.0.0.2/12:34:56:78:9a:bc + +or:: + + insmod netconsole netconsole=@/,@10.0.0.2/ + +or using IPv6:: + + insmod netconsole netconsole=@/,@fd00:1:2:3::1/ + +It also supports logging to multiple remote agents by specifying +parameters for the multiple agents separated by semicolons and the +complete string enclosed in "quotes", thusly:: + + modprobe netconsole netconsole="@/,@10.0.0.2/;@/eth1,6892@10.0.0.3/" + +Built-in netconsole starts immediately after the TCP stack is +initialized and attempts to bring up the supplied dev at the supplied +address. + +The remote host has several options to receive the kernel messages, +for example: + +1) syslogd + +2) netcat + + On distributions using a BSD-based netcat version (e.g. Fedora, + openSUSE and Ubuntu) the listening port must be specified without + the -p switch:: + + nc -u -l -p ' / 'nc -u -l + + or:: + + netcat -u -l -p ' / 'netcat -u -l + +3) socat + +:: + + socat udp-recv: - + +Dynamic reconfiguration: +======================== + +Dynamic reconfigurability is a useful addition to netconsole that enables +remote logging targets to be dynamically added, removed, or have their +parameters reconfigured at runtime from a configfs-based userspace interface. +[ Note that the parameters of netconsole targets that were specified/created +from the boot/module option are not exposed via this interface, and hence +cannot be modified dynamically. ] + +To include this feature, select CONFIG_NETCONSOLE_DYNAMIC when building the +netconsole module (or kernel, if netconsole is built-in). + +Some examples follow (where configfs is mounted at the /sys/kernel/config +mountpoint). + +To add a remote logging target (target names can be arbitrary):: + + cd /sys/kernel/config/netconsole/ + mkdir target1 + +Note that newly created targets have default parameter values (as mentioned +above) and are disabled by default -- they must first be enabled by writing +"1" to the "enabled" attribute (usually after setting parameters accordingly) +as described below. + +To remove a target:: + + rmdir /sys/kernel/config/netconsole/othertarget/ + +The interface exposes these parameters of a netconsole target to userspace: + + ============== ================================= ============ + enabled Is this target currently enabled? (read-write) + extended Extended mode enabled (read-write) + dev_name Local network interface name (read-write) + local_port Source UDP port to use (read-write) + remote_port Remote agent's UDP port (read-write) + local_ip Source IP address to use (read-write) + remote_ip Remote agent's IP address (read-write) + local_mac Local interface's MAC address (read-only) + remote_mac Remote agent's MAC address (read-write) + ============== ================================= ============ + +The "enabled" attribute is also used to control whether the parameters of +a target can be updated or not -- you can modify the parameters of only +disabled targets (i.e. if "enabled" is 0). + +To update a target's parameters:: + + cat enabled # check if enabled is 1 + echo 0 > enabled # disable the target (if required) + echo eth2 > dev_name # set local interface + echo 10.0.0.4 > remote_ip # update some parameter + echo cb:a9:87:65:43:21 > remote_mac # update more parameters + echo 1 > enabled # enable target again + +You can also update the local interface dynamically. This is especially +useful if you want to use interfaces that have newly come up (and may not +have existed when netconsole was loaded / initialized). + +Extended console: +================= + +If '+' is prefixed to the configuration line or "extended" config file +is set to 1, extended console support is enabled. An example boot +param follows:: + + linux netconsole=+4444@10.0.0.1/eth1,9353@10.0.0.2/12:34:56:78:9a:bc + +Log messages are transmitted with extended metadata header in the +following format which is the same as /dev/kmsg:: + + ,,,; + +Non printable characters in are escaped using "\xff" +notation. If the message contains optional dictionary, verbatim +newline is used as the delimeter. + +If a message doesn't fit in certain number of bytes (currently 1000), +the message is split into multiple fragments by netconsole. These +fragments are transmitted with "ncfrag" header field added:: + + ncfrag=/ + +For example, assuming a lot smaller chunk size, a message "the first +chunk, the 2nd chunk." may be split as follows:: + + 6,416,1758426,-,ncfrag=0/31;the first chunk, + 6,416,1758426,-,ncfrag=16/31; the 2nd chunk. + +Miscellaneous notes: +==================== + +.. Warning:: + + the default target ethernet setting uses the broadcast + ethernet address to send packets, which can cause increased load on + other systems on the same ethernet segment. + +.. Tip:: + + some LAN switches may be configured to suppress ethernet broadcasts + so it is advised to explicitly specify the remote agents' MAC addresses + from the config parameters passed to netconsole. + +.. Tip:: + + to find out the MAC address of, say, 10.0.0.2, you may try using:: + + ping -c 1 10.0.0.2 ; /sbin/arp -n | grep 10.0.0.2 + +.. Tip:: + + in case the remote logging agent is on a separate LAN subnet than + the sender, it is suggested to try specifying the MAC address of the + default gateway (you may use /sbin/route -n to find it out) as the + remote MAC address instead. + +.. note:: + + the network device (eth1 in the above case) can run any kind + of other network traffic, netconsole is not intrusive. Netconsole + might cause slight delays in other traffic if the volume of kernel + messages is high, but should have no other impact. + +.. note:: + + if you find that the remote logging agent is not receiving or + printing all messages from the sender, it is likely that you have set + the "console_loglevel" parameter (on the sender) to only send high + priority messages to the console. You can change this at runtime using:: + + dmesg -n 8 + + or by specifying "debug" on the kernel command line at boot, to send + all kernel messages to the console. A specific value for this parameter + can also be set using the "loglevel" kernel boot option. See the + dmesg(8) man page and Documentation/admin-guide/kernel-parameters.rst + for details. + +Netconsole was designed to be as instantaneous as possible, to +enable the logging of even the most critical kernel bugs. It works +from IRQ contexts as well, and does not enable interrupts while +sending packets. Due to these unique needs, configuration cannot +be more automatic, and some fundamental limitations will remain: +only IP networks, UDP packets and ethernet devices are supported. -- cgit v1.2.3