From 2c3c1048746a4622d8c89a29670120dc8fab93c4 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 7 Apr 2024 20:49:45 +0200 Subject: Adding upstream version 6.1.76. Signed-off-by: Daniel Baumann --- .../userspace-api/media/rc/lirc-dev-intro.rst | 176 +++++++++++++++++++++ 1 file changed, 176 insertions(+) create mode 100644 Documentation/userspace-api/media/rc/lirc-dev-intro.rst (limited to 'Documentation/userspace-api/media/rc/lirc-dev-intro.rst') diff --git a/Documentation/userspace-api/media/rc/lirc-dev-intro.rst b/Documentation/userspace-api/media/rc/lirc-dev-intro.rst new file mode 100644 index 000000000..d899331b9 --- /dev/null +++ b/Documentation/userspace-api/media/rc/lirc-dev-intro.rst @@ -0,0 +1,176 @@ +.. SPDX-License-Identifier: GPL-2.0 OR GFDL-1.1-no-invariants-or-later + +.. _lirc_dev_intro: + +************ +Introduction +************ + +LIRC stands for Linux Infrared Remote Control. The LIRC device interface is +a bi-directional interface for transporting raw IR and decoded scancodes +data between userspace and kernelspace. Fundamentally, it is just a chardev +(/dev/lircX, for X = 0, 1, 2, ...), with a number of standard struct +file_operations defined on it. With respect to transporting raw IR and +decoded scancodes to and fro, the essential fops are read, write and ioctl. + +It is also possible to attach a BPF program to a LIRC device for decoding +raw IR into scancodes. + +Example dmesg output upon a driver registering w/LIRC: + +.. code-block:: none + + $ dmesg |grep lirc_dev + rc rc0: lirc_dev: driver mceusb registered at minor = 0, raw IR receiver, raw IR transmitter + +What you should see for a chardev: + +.. code-block:: none + + $ ls -l /dev/lirc* + crw-rw---- 1 root root 248, 0 Jul 2 22:20 /dev/lirc0 + +Note that the package `v4l-utils `_ +contains tools for working with LIRC devices: + + - ir-ctl: can receive raw IR and transmit IR, as well as query LIRC + device features. + + - ir-keytable: can load keymaps; allows you to set IR kernel protocols; load + BPF IR decoders and test IR decoding. Some BPF IR decoders are also + provided. + +.. _lirc_modes: + +********** +LIRC modes +********** + +LIRC supports some modes of receiving and sending IR codes, as shown +on the following table. + +.. _lirc-mode-scancode: +.. _lirc-scancode-flag-toggle: +.. _lirc-scancode-flag-repeat: + +``LIRC_MODE_SCANCODE`` + + This mode is for both sending and receiving IR. + + For transmitting (aka sending), create a struct lirc_scancode with + the desired scancode set in the ``scancode`` member, :c:type:`rc_proto` + set to the :ref:`IR protocol `, and all other + members set to 0. Write this struct to the lirc device. + + For receiving, you read struct lirc_scancode from the LIRC device. + The ``scancode`` field is set to the received scancode and the + :ref:`IR protocol ` is set in + :c:type:`rc_proto`. If the scancode maps to a valid key code, this is set + in the ``keycode`` field, else it is set to ``KEY_RESERVED``. + + The ``flags`` can have ``LIRC_SCANCODE_FLAG_TOGGLE`` set if the toggle + bit is set in protocols that support it (e.g. rc-5 and rc-6), or + ``LIRC_SCANCODE_FLAG_REPEAT`` for when a repeat is received for protocols + that support it (e.g. nec). + + In the Sanyo and NEC protocol, if you hold a button on remote, rather than + repeating the entire scancode, the remote sends a shorter message with + no scancode, which just means button is held, a "repeat". When this is + received, the ``LIRC_SCANCODE_FLAG_REPEAT`` is set and the scancode and + keycode is repeated. + + With nec, there is no way to distinguish "button hold" from "repeatedly + pressing the same button". The rc-5 and rc-6 protocols have a toggle bit. + When a button is released and pressed again, the toggle bit is inverted. + If the toggle bit is set, the ``LIRC_SCANCODE_FLAG_TOGGLE`` is set. + + The ``timestamp`` field is filled with the time nanoseconds + (in ``CLOCK_MONOTONIC``) when the scancode was decoded. + +.. _lirc-mode-mode2: + +``LIRC_MODE_MODE2`` + + The driver returns a sequence of pulse and space codes to userspace, + as a series of u32 values. + + This mode is used only for IR receive. + + The upper 8 bits determine the packet type, and the lower 24 bits + the payload. Use ``LIRC_VALUE()`` macro to get the payload, and + the macro ``LIRC_MODE2()`` will give you the type, which + is one of: + + ``LIRC_MODE2_PULSE`` + + Signifies the presence of IR in microseconds, also known as *flash*. + + ``LIRC_MODE2_SPACE`` + + Signifies absence of IR in microseconds, also known as *gap*. + + ``LIRC_MODE2_FREQUENCY`` + + If measurement of the carrier frequency was enabled with + :ref:`lirc_set_measure_carrier_mode` then this packet gives you + the carrier frequency in Hertz. + + ``LIRC_MODE2_TIMEOUT`` + + When the timeout set with :ref:`lirc_set_rec_timeout` expires due + to no IR being detected, this packet will be sent, with the number + of microseconds with no IR. + + ``LIRC_MODE2_OVERFLOW`` + + Signifies that the IR receiver encounter an overflow, and some IR + is missing. The IR data after this should be correct again. The + actual value is not important, but this is set to 0xffffff by the + kernel for compatibility with lircd. + +.. _lirc-mode-pulse: + +``LIRC_MODE_PULSE`` + + In pulse mode, a sequence of pulse/space integer values are written to the + lirc device using :ref:`lirc-write`. + + The values are alternating pulse and space lengths, in microseconds. The + first and last entry must be a pulse, so there must be an odd number + of entries. + + This mode is used only for IR send. + +************************************* +Data types used by LIRC_MODE_SCANCODE +************************************* + +.. kernel-doc:: include/uapi/linux/lirc.h + :identifiers: lirc_scancode rc_proto + +******************** +BPF based IR decoder +******************** + +The kernel has support for decoding the most common +:ref:`IR protocols `, but there +are many protocols which are not supported. To support these, it is possible +to load an BPF program which does the decoding. This can only be done on +LIRC devices which support reading raw IR. + +First, using the `bpf(2)`_ syscall with the ``BPF_LOAD_PROG`` argument, +program must be loaded of type ``BPF_PROG_TYPE_LIRC_MODE2``. Once attached +to the LIRC device, this program will be called for each pulse, space or +timeout event on the LIRC device. The context for the BPF program is a +pointer to a unsigned int, which is a :ref:`LIRC_MODE_MODE2 ` +value. When the program has decoded the scancode, it can be submitted using +the BPF functions ``bpf_rc_keydown()`` or ``bpf_rc_repeat()``. Mouse or pointer +movements can be reported using ``bpf_rc_pointer_rel()``. + +Once you have the file descriptor for the ``BPF_PROG_TYPE_LIRC_MODE2`` BPF +program, it can be attached to the LIRC device using the `bpf(2)`_ syscall. +The target must be the file descriptor for the LIRC device, and the +attach type must be ``BPF_LIRC_MODE2``. No more than 64 BPF programs can be +attached to a single LIRC device at a time. + +.. _bpf(2): http://man7.org/linux/man-pages/man2/bpf.2.html -- cgit v1.2.3