From 2c3c1048746a4622d8c89a29670120dc8fab93c4 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 7 Apr 2024 20:49:45 +0200 Subject: Adding upstream version 6.1.76. Signed-off-by: Daniel Baumann --- drivers/usb/host/xhci-ring.c | 4385 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 4385 insertions(+) create mode 100644 drivers/usb/host/xhci-ring.c (limited to 'drivers/usb/host/xhci-ring.c') diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c new file mode 100644 index 000000000..1239e06df --- /dev/null +++ b/drivers/usb/host/xhci-ring.c @@ -0,0 +1,4385 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * xHCI host controller driver + * + * Copyright (C) 2008 Intel Corp. + * + * Author: Sarah Sharp + * Some code borrowed from the Linux EHCI driver. + */ + +/* + * Ring initialization rules: + * 1. Each segment is initialized to zero, except for link TRBs. + * 2. Ring cycle state = 0. This represents Producer Cycle State (PCS) or + * Consumer Cycle State (CCS), depending on ring function. + * 3. Enqueue pointer = dequeue pointer = address of first TRB in the segment. + * + * Ring behavior rules: + * 1. A ring is empty if enqueue == dequeue. This means there will always be at + * least one free TRB in the ring. This is useful if you want to turn that + * into a link TRB and expand the ring. + * 2. When incrementing an enqueue or dequeue pointer, if the next TRB is a + * link TRB, then load the pointer with the address in the link TRB. If the + * link TRB had its toggle bit set, you may need to update the ring cycle + * state (see cycle bit rules). You may have to do this multiple times + * until you reach a non-link TRB. + * 3. A ring is full if enqueue++ (for the definition of increment above) + * equals the dequeue pointer. + * + * Cycle bit rules: + * 1. When a consumer increments a dequeue pointer and encounters a toggle bit + * in a link TRB, it must toggle the ring cycle state. + * 2. When a producer increments an enqueue pointer and encounters a toggle bit + * in a link TRB, it must toggle the ring cycle state. + * + * Producer rules: + * 1. Check if ring is full before you enqueue. + * 2. Write the ring cycle state to the cycle bit in the TRB you're enqueuing. + * Update enqueue pointer between each write (which may update the ring + * cycle state). + * 3. Notify consumer. If SW is producer, it rings the doorbell for command + * and endpoint rings. If HC is the producer for the event ring, + * and it generates an interrupt according to interrupt modulation rules. + * + * Consumer rules: + * 1. Check if TRB belongs to you. If the cycle bit == your ring cycle state, + * the TRB is owned by the consumer. + * 2. Update dequeue pointer (which may update the ring cycle state) and + * continue processing TRBs until you reach a TRB which is not owned by you. + * 3. Notify the producer. SW is the consumer for the event ring, and it + * updates event ring dequeue pointer. HC is the consumer for the command and + * endpoint rings; it generates events on the event ring for these. + */ + +#include +#include +#include +#include "xhci.h" +#include "xhci-trace.h" + +static int queue_command(struct xhci_hcd *xhci, struct xhci_command *cmd, + u32 field1, u32 field2, + u32 field3, u32 field4, bool command_must_succeed); + +/* + * Returns zero if the TRB isn't in this segment, otherwise it returns the DMA + * address of the TRB. + */ +dma_addr_t xhci_trb_virt_to_dma(struct xhci_segment *seg, + union xhci_trb *trb) +{ + unsigned long segment_offset; + + if (!seg || !trb || trb < seg->trbs) + return 0; + /* offset in TRBs */ + segment_offset = trb - seg->trbs; + if (segment_offset >= TRBS_PER_SEGMENT) + return 0; + return seg->dma + (segment_offset * sizeof(*trb)); +} + +static bool trb_is_noop(union xhci_trb *trb) +{ + return TRB_TYPE_NOOP_LE32(trb->generic.field[3]); +} + +static bool trb_is_link(union xhci_trb *trb) +{ + return TRB_TYPE_LINK_LE32(trb->link.control); +} + +static bool last_trb_on_seg(struct xhci_segment *seg, union xhci_trb *trb) +{ + return trb == &seg->trbs[TRBS_PER_SEGMENT - 1]; +} + +static bool last_trb_on_ring(struct xhci_ring *ring, + struct xhci_segment *seg, union xhci_trb *trb) +{ + return last_trb_on_seg(seg, trb) && (seg->next == ring->first_seg); +} + +static bool link_trb_toggles_cycle(union xhci_trb *trb) +{ + return le32_to_cpu(trb->link.control) & LINK_TOGGLE; +} + +static bool last_td_in_urb(struct xhci_td *td) +{ + struct urb_priv *urb_priv = td->urb->hcpriv; + + return urb_priv->num_tds_done == urb_priv->num_tds; +} + +static void inc_td_cnt(struct urb *urb) +{ + struct urb_priv *urb_priv = urb->hcpriv; + + urb_priv->num_tds_done++; +} + +static void trb_to_noop(union xhci_trb *trb, u32 noop_type) +{ + if (trb_is_link(trb)) { + /* unchain chained link TRBs */ + trb->link.control &= cpu_to_le32(~TRB_CHAIN); + } else { + trb->generic.field[0] = 0; + trb->generic.field[1] = 0; + trb->generic.field[2] = 0; + /* Preserve only the cycle bit of this TRB */ + trb->generic.field[3] &= cpu_to_le32(TRB_CYCLE); + trb->generic.field[3] |= cpu_to_le32(TRB_TYPE(noop_type)); + } +} + +/* Updates trb to point to the next TRB in the ring, and updates seg if the next + * TRB is in a new segment. This does not skip over link TRBs, and it does not + * effect the ring dequeue or enqueue pointers. + */ +static void next_trb(struct xhci_hcd *xhci, + struct xhci_ring *ring, + struct xhci_segment **seg, + union xhci_trb **trb) +{ + if (trb_is_link(*trb)) { + *seg = (*seg)->next; + *trb = ((*seg)->trbs); + } else { + (*trb)++; + } +} + +/* + * See Cycle bit rules. SW is the consumer for the event ring only. + */ +void inc_deq(struct xhci_hcd *xhci, struct xhci_ring *ring) +{ + unsigned int link_trb_count = 0; + + /* event ring doesn't have link trbs, check for last trb */ + if (ring->type == TYPE_EVENT) { + if (!last_trb_on_seg(ring->deq_seg, ring->dequeue)) { + ring->dequeue++; + goto out; + } + if (last_trb_on_ring(ring, ring->deq_seg, ring->dequeue)) + ring->cycle_state ^= 1; + ring->deq_seg = ring->deq_seg->next; + ring->dequeue = ring->deq_seg->trbs; + goto out; + } + + /* All other rings have link trbs */ + if (!trb_is_link(ring->dequeue)) { + if (last_trb_on_seg(ring->deq_seg, ring->dequeue)) { + xhci_warn(xhci, "Missing link TRB at end of segment\n"); + } else { + ring->dequeue++; + ring->num_trbs_free++; + } + } + + while (trb_is_link(ring->dequeue)) { + ring->deq_seg = ring->deq_seg->next; + ring->dequeue = ring->deq_seg->trbs; + + if (link_trb_count++ > ring->num_segs) { + xhci_warn(xhci, "Ring is an endless link TRB loop\n"); + break; + } + } +out: + trace_xhci_inc_deq(ring); + + return; +} + +/* + * See Cycle bit rules. SW is the consumer for the event ring only. + * + * If we've just enqueued a TRB that is in the middle of a TD (meaning the + * chain bit is set), then set the chain bit in all the following link TRBs. + * If we've enqueued the last TRB in a TD, make sure the following link TRBs + * have their chain bit cleared (so that each Link TRB is a separate TD). + * + * Section 6.4.4.1 of the 0.95 spec says link TRBs cannot have the chain bit + * set, but other sections talk about dealing with the chain bit set. This was + * fixed in the 0.96 specification errata, but we have to assume that all 0.95 + * xHCI hardware can't handle the chain bit being cleared on a link TRB. + * + * @more_trbs_coming: Will you enqueue more TRBs before calling + * prepare_transfer()? + */ +static void inc_enq(struct xhci_hcd *xhci, struct xhci_ring *ring, + bool more_trbs_coming) +{ + u32 chain; + union xhci_trb *next; + unsigned int link_trb_count = 0; + + chain = le32_to_cpu(ring->enqueue->generic.field[3]) & TRB_CHAIN; + /* If this is not event ring, there is one less usable TRB */ + if (!trb_is_link(ring->enqueue)) + ring->num_trbs_free--; + + if (last_trb_on_seg(ring->enq_seg, ring->enqueue)) { + xhci_err(xhci, "Tried to move enqueue past ring segment\n"); + return; + } + + next = ++(ring->enqueue); + + /* Update the dequeue pointer further if that was a link TRB */ + while (trb_is_link(next)) { + + /* + * If the caller doesn't plan on enqueueing more TDs before + * ringing the doorbell, then we don't want to give the link TRB + * to the hardware just yet. We'll give the link TRB back in + * prepare_ring() just before we enqueue the TD at the top of + * the ring. + */ + if (!chain && !more_trbs_coming) + break; + + /* If we're not dealing with 0.95 hardware or isoc rings on + * AMD 0.96 host, carry over the chain bit of the previous TRB + * (which may mean the chain bit is cleared). + */ + if (!(ring->type == TYPE_ISOC && + (xhci->quirks & XHCI_AMD_0x96_HOST)) && + !xhci_link_trb_quirk(xhci)) { + next->link.control &= cpu_to_le32(~TRB_CHAIN); + next->link.control |= cpu_to_le32(chain); + } + /* Give this link TRB to the hardware */ + wmb(); + next->link.control ^= cpu_to_le32(TRB_CYCLE); + + /* Toggle the cycle bit after the last ring segment. */ + if (link_trb_toggles_cycle(next)) + ring->cycle_state ^= 1; + + ring->enq_seg = ring->enq_seg->next; + ring->enqueue = ring->enq_seg->trbs; + next = ring->enqueue; + + if (link_trb_count++ > ring->num_segs) { + xhci_warn(xhci, "%s: Ring link TRB loop\n", __func__); + break; + } + } + + trace_xhci_inc_enq(ring); +} + +static int xhci_num_trbs_to(struct xhci_segment *start_seg, union xhci_trb *start, + struct xhci_segment *end_seg, union xhci_trb *end, + unsigned int num_segs) +{ + union xhci_trb *last_on_seg; + int num = 0; + int i = 0; + + do { + if (start_seg == end_seg && end >= start) + return num + (end - start); + last_on_seg = &start_seg->trbs[TRBS_PER_SEGMENT - 1]; + num += last_on_seg - start; + start_seg = start_seg->next; + start = start_seg->trbs; + } while (i++ <= num_segs); + + return -EINVAL; +} + +/* + * Check to see if there's room to enqueue num_trbs on the ring and make sure + * enqueue pointer will not advance into dequeue segment. See rules above. + */ +static inline int room_on_ring(struct xhci_hcd *xhci, struct xhci_ring *ring, + unsigned int num_trbs) +{ + int num_trbs_in_deq_seg; + + if (ring->num_trbs_free < num_trbs) + return 0; + + if (ring->type != TYPE_COMMAND && ring->type != TYPE_EVENT) { + num_trbs_in_deq_seg = ring->dequeue - ring->deq_seg->trbs; + if (ring->num_trbs_free < num_trbs + num_trbs_in_deq_seg) + return 0; + } + + return 1; +} + +/* Ring the host controller doorbell after placing a command on the ring */ +void xhci_ring_cmd_db(struct xhci_hcd *xhci) +{ + if (!(xhci->cmd_ring_state & CMD_RING_STATE_RUNNING)) + return; + + xhci_dbg(xhci, "// Ding dong!\n"); + + trace_xhci_ring_host_doorbell(0, DB_VALUE_HOST); + + writel(DB_VALUE_HOST, &xhci->dba->doorbell[0]); + /* Flush PCI posted writes */ + readl(&xhci->dba->doorbell[0]); +} + +static bool xhci_mod_cmd_timer(struct xhci_hcd *xhci, unsigned long delay) +{ + return mod_delayed_work(system_wq, &xhci->cmd_timer, delay); +} + +static struct xhci_command *xhci_next_queued_cmd(struct xhci_hcd *xhci) +{ + return list_first_entry_or_null(&xhci->cmd_list, struct xhci_command, + cmd_list); +} + +/* + * Turn all commands on command ring with status set to "aborted" to no-op trbs. + * If there are other commands waiting then restart the ring and kick the timer. + * This must be called with command ring stopped and xhci->lock held. + */ +static void xhci_handle_stopped_cmd_ring(struct xhci_hcd *xhci, + struct xhci_command *cur_cmd) +{ + struct xhci_command *i_cmd; + + /* Turn all aborted commands in list to no-ops, then restart */ + list_for_each_entry(i_cmd, &xhci->cmd_list, cmd_list) { + + if (i_cmd->status != COMP_COMMAND_ABORTED) + continue; + + i_cmd->status = COMP_COMMAND_RING_STOPPED; + + xhci_dbg(xhci, "Turn aborted command %p to no-op\n", + i_cmd->command_trb); + + trb_to_noop(i_cmd->command_trb, TRB_CMD_NOOP); + + /* + * caller waiting for completion is called when command + * completion event is received for these no-op commands + */ + } + + xhci->cmd_ring_state = CMD_RING_STATE_RUNNING; + + /* ring command ring doorbell to restart the command ring */ + if ((xhci->cmd_ring->dequeue != xhci->cmd_ring->enqueue) && + !(xhci->xhc_state & XHCI_STATE_DYING)) { + xhci->current_cmd = cur_cmd; + xhci_mod_cmd_timer(xhci, XHCI_CMD_DEFAULT_TIMEOUT); + xhci_ring_cmd_db(xhci); + } +} + +/* Must be called with xhci->lock held, releases and aquires lock back */ +static int xhci_abort_cmd_ring(struct xhci_hcd *xhci, unsigned long flags) +{ + struct xhci_segment *new_seg = xhci->cmd_ring->deq_seg; + union xhci_trb *new_deq = xhci->cmd_ring->dequeue; + u64 crcr; + int ret; + + xhci_dbg(xhci, "Abort command ring\n"); + + reinit_completion(&xhci->cmd_ring_stop_completion); + + /* + * The control bits like command stop, abort are located in lower + * dword of the command ring control register. + * Some controllers require all 64 bits to be written to abort the ring. + * Make sure the upper dword is valid, pointing to the next command, + * avoiding corrupting the command ring pointer in case the command ring + * is stopped by the time the upper dword is written. + */ + next_trb(xhci, NULL, &new_seg, &new_deq); + if (trb_is_link(new_deq)) + next_trb(xhci, NULL, &new_seg, &new_deq); + + crcr = xhci_trb_virt_to_dma(new_seg, new_deq); + xhci_write_64(xhci, crcr | CMD_RING_ABORT, &xhci->op_regs->cmd_ring); + + /* Section 4.6.1.2 of xHCI 1.0 spec says software should also time the + * completion of the Command Abort operation. If CRR is not negated in 5 + * seconds then driver handles it as if host died (-ENODEV). + * In the future we should distinguish between -ENODEV and -ETIMEDOUT + * and try to recover a -ETIMEDOUT with a host controller reset. + */ + ret = xhci_handshake(&xhci->op_regs->cmd_ring, + CMD_RING_RUNNING, 0, 5 * 1000 * 1000); + if (ret < 0) { + xhci_err(xhci, "Abort failed to stop command ring: %d\n", ret); + xhci_halt(xhci); + xhci_hc_died(xhci); + return ret; + } + /* + * Writing the CMD_RING_ABORT bit should cause a cmd completion event, + * however on some host hw the CMD_RING_RUNNING bit is correctly cleared + * but the completion event in never sent. Wait 2 secs (arbitrary + * number) to handle those cases after negation of CMD_RING_RUNNING. + */ + spin_unlock_irqrestore(&xhci->lock, flags); + ret = wait_for_completion_timeout(&xhci->cmd_ring_stop_completion, + msecs_to_jiffies(2000)); + spin_lock_irqsave(&xhci->lock, flags); + if (!ret) { + xhci_dbg(xhci, "No stop event for abort, ring start fail?\n"); + xhci_cleanup_command_queue(xhci); + } else { + xhci_handle_stopped_cmd_ring(xhci, xhci_next_queued_cmd(xhci)); + } + return 0; +} + +void xhci_ring_ep_doorbell(struct xhci_hcd *xhci, + unsigned int slot_id, + unsigned int ep_index, + unsigned int stream_id) +{ + __le32 __iomem *db_addr = &xhci->dba->doorbell[slot_id]; + struct xhci_virt_ep *ep = &xhci->devs[slot_id]->eps[ep_index]; + unsigned int ep_state = ep->ep_state; + + /* Don't ring the doorbell for this endpoint if there are pending + * cancellations because we don't want to interrupt processing. + * We don't want to restart any stream rings if there's a set dequeue + * pointer command pending because the device can choose to start any + * stream once the endpoint is on the HW schedule. + */ + if ((ep_state & EP_STOP_CMD_PENDING) || (ep_state & SET_DEQ_PENDING) || + (ep_state & EP_HALTED) || (ep_state & EP_CLEARING_TT)) + return; + + trace_xhci_ring_ep_doorbell(slot_id, DB_VALUE(ep_index, stream_id)); + + writel(DB_VALUE(ep_index, stream_id), db_addr); + /* flush the write */ + readl(db_addr); +} + +/* Ring the doorbell for any rings with pending URBs */ +static void ring_doorbell_for_active_rings(struct xhci_hcd *xhci, + unsigned int slot_id, + unsigned int ep_index) +{ + unsigned int stream_id; + struct xhci_virt_ep *ep; + + ep = &xhci->devs[slot_id]->eps[ep_index]; + + /* A ring has pending URBs if its TD list is not empty */ + if (!(ep->ep_state & EP_HAS_STREAMS)) { + if (ep->ring && !(list_empty(&ep->ring->td_list))) + xhci_ring_ep_doorbell(xhci, slot_id, ep_index, 0); + return; + } + + for (stream_id = 1; stream_id < ep->stream_info->num_streams; + stream_id++) { + struct xhci_stream_info *stream_info = ep->stream_info; + if (!list_empty(&stream_info->stream_rings[stream_id]->td_list)) + xhci_ring_ep_doorbell(xhci, slot_id, ep_index, + stream_id); + } +} + +void xhci_ring_doorbell_for_active_rings(struct xhci_hcd *xhci, + unsigned int slot_id, + unsigned int ep_index) +{ + ring_doorbell_for_active_rings(xhci, slot_id, ep_index); +} + +static struct xhci_virt_ep *xhci_get_virt_ep(struct xhci_hcd *xhci, + unsigned int slot_id, + unsigned int ep_index) +{ + if (slot_id == 0 || slot_id >= MAX_HC_SLOTS) { + xhci_warn(xhci, "Invalid slot_id %u\n", slot_id); + return NULL; + } + if (ep_index >= EP_CTX_PER_DEV) { + xhci_warn(xhci, "Invalid endpoint index %u\n", ep_index); + return NULL; + } + if (!xhci->devs[slot_id]) { + xhci_warn(xhci, "No xhci virt device for slot_id %u\n", slot_id); + return NULL; + } + + return &xhci->devs[slot_id]->eps[ep_index]; +} + +static struct xhci_ring *xhci_virt_ep_to_ring(struct xhci_hcd *xhci, + struct xhci_virt_ep *ep, + unsigned int stream_id) +{ + /* common case, no streams */ + if (!(ep->ep_state & EP_HAS_STREAMS)) + return ep->ring; + + if (!ep->stream_info) + return NULL; + + if (stream_id == 0 || stream_id >= ep->stream_info->num_streams) { + xhci_warn(xhci, "Invalid stream_id %u request for slot_id %u ep_index %u\n", + stream_id, ep->vdev->slot_id, ep->ep_index); + return NULL; + } + + return ep->stream_info->stream_rings[stream_id]; +} + +/* Get the right ring for the given slot_id, ep_index and stream_id. + * If the endpoint supports streams, boundary check the URB's stream ID. + * If the endpoint doesn't support streams, return the singular endpoint ring. + */ +struct xhci_ring *xhci_triad_to_transfer_ring(struct xhci_hcd *xhci, + unsigned int slot_id, unsigned int ep_index, + unsigned int stream_id) +{ + struct xhci_virt_ep *ep; + + ep = xhci_get_virt_ep(xhci, slot_id, ep_index); + if (!ep) + return NULL; + + return xhci_virt_ep_to_ring(xhci, ep, stream_id); +} + + +/* + * Get the hw dequeue pointer xHC stopped on, either directly from the + * endpoint context, or if streams are in use from the stream context. + * The returned hw_dequeue contains the lowest four bits with cycle state + * and possbile stream context type. + */ +static u64 xhci_get_hw_deq(struct xhci_hcd *xhci, struct xhci_virt_device *vdev, + unsigned int ep_index, unsigned int stream_id) +{ + struct xhci_ep_ctx *ep_ctx; + struct xhci_stream_ctx *st_ctx; + struct xhci_virt_ep *ep; + + ep = &vdev->eps[ep_index]; + + if (ep->ep_state & EP_HAS_STREAMS) { + st_ctx = &ep->stream_info->stream_ctx_array[stream_id]; + return le64_to_cpu(st_ctx->stream_ring); + } + ep_ctx = xhci_get_ep_ctx(xhci, vdev->out_ctx, ep_index); + return le64_to_cpu(ep_ctx->deq); +} + +static int xhci_move_dequeue_past_td(struct xhci_hcd *xhci, + unsigned int slot_id, unsigned int ep_index, + unsigned int stream_id, struct xhci_td *td) +{ + struct xhci_virt_device *dev = xhci->devs[slot_id]; + struct xhci_virt_ep *ep = &dev->eps[ep_index]; + struct xhci_ring *ep_ring; + struct xhci_command *cmd; + struct xhci_segment *new_seg; + union xhci_trb *new_deq; + int new_cycle; + dma_addr_t addr; + u64 hw_dequeue; + bool cycle_found = false; + bool td_last_trb_found = false; + u32 trb_sct = 0; + int ret; + + ep_ring = xhci_triad_to_transfer_ring(xhci, slot_id, + ep_index, stream_id); + if (!ep_ring) { + xhci_warn(xhci, "WARN can't find new dequeue, invalid stream ID %u\n", + stream_id); + return -ENODEV; + } + /* + * A cancelled TD can complete with a stall if HW cached the trb. + * In this case driver can't find td, but if the ring is empty we + * can move the dequeue pointer to the current enqueue position. + * We shouldn't hit this anymore as cached cancelled TRBs are given back + * after clearing the cache, but be on the safe side and keep it anyway + */ + if (!td) { + if (list_empty(&ep_ring->td_list)) { + new_seg = ep_ring->enq_seg; + new_deq = ep_ring->enqueue; + new_cycle = ep_ring->cycle_state; + xhci_dbg(xhci, "ep ring empty, Set new dequeue = enqueue"); + goto deq_found; + } else { + xhci_warn(xhci, "Can't find new dequeue state, missing td\n"); + return -EINVAL; + } + } + + hw_dequeue = xhci_get_hw_deq(xhci, dev, ep_index, stream_id); + new_seg = ep_ring->deq_seg; + new_deq = ep_ring->dequeue; + new_cycle = hw_dequeue & 0x1; + + /* + * We want to find the pointer, segment and cycle state of the new trb + * (the one after current TD's last_trb). We know the cycle state at + * hw_dequeue, so walk the ring until both hw_dequeue and last_trb are + * found. + */ + do { + if (!cycle_found && xhci_trb_virt_to_dma(new_seg, new_deq) + == (dma_addr_t)(hw_dequeue & ~0xf)) { + cycle_found = true; + if (td_last_trb_found) + break; + } + if (new_deq == td->last_trb) + td_last_trb_found = true; + + if (cycle_found && trb_is_link(new_deq) && + link_trb_toggles_cycle(new_deq)) + new_cycle ^= 0x1; + + next_trb(xhci, ep_ring, &new_seg, &new_deq); + + /* Search wrapped around, bail out */ + if (new_deq == ep->ring->dequeue) { + xhci_err(xhci, "Error: Failed finding new dequeue state\n"); + return -EINVAL; + } + + } while (!cycle_found || !td_last_trb_found); + +deq_found: + + /* Don't update the ring cycle state for the producer (us). */ + addr = xhci_trb_virt_to_dma(new_seg, new_deq); + if (addr == 0) { + xhci_warn(xhci, "Can't find dma of new dequeue ptr\n"); + xhci_warn(xhci, "deq seg = %p, deq ptr = %p\n", new_seg, new_deq); + return -EINVAL; + } + + if ((ep->ep_state & SET_DEQ_PENDING)) { + xhci_warn(xhci, "Set TR Deq already pending, don't submit for 0x%pad\n", + &addr); + return -EBUSY; + } + + /* This function gets called from contexts where it cannot sleep */ + cmd = xhci_alloc_command(xhci, false, GFP_ATOMIC); + if (!cmd) { + xhci_warn(xhci, "Can't alloc Set TR Deq cmd 0x%pad\n", &addr); + return -ENOMEM; + } + + if (stream_id) + trb_sct = SCT_FOR_TRB(SCT_PRI_TR); + ret = queue_command(xhci, cmd, + lower_32_bits(addr) | trb_sct | new_cycle, + upper_32_bits(addr), + STREAM_ID_FOR_TRB(stream_id), SLOT_ID_FOR_TRB(slot_id) | + EP_ID_FOR_TRB(ep_index) | TRB_TYPE(TRB_SET_DEQ), false); + if (ret < 0) { + xhci_free_command(xhci, cmd); + return ret; + } + ep->queued_deq_seg = new_seg; + ep->queued_deq_ptr = new_deq; + + xhci_dbg_trace(xhci, trace_xhci_dbg_cancel_urb, + "Set TR Deq ptr 0x%llx, cycle %u\n", addr, new_cycle); + + /* Stop the TD queueing code from ringing the doorbell until + * this command completes. The HC won't set the dequeue pointer + * if the ring is running, and ringing the doorbell starts the + * ring running. + */ + ep->ep_state |= SET_DEQ_PENDING; + xhci_ring_cmd_db(xhci); + return 0; +} + +/* flip_cycle means flip the cycle bit of all but the first and last TRB. + * (The last TRB actually points to the ring enqueue pointer, which is not part + * of this TD.) This is used to remove partially enqueued isoc TDs from a ring. + */ +static void td_to_noop(struct xhci_hcd *xhci, struct xhci_ring *ep_ring, + struct xhci_td *td, bool flip_cycle) +{ + struct xhci_segment *seg = td->start_seg; + union xhci_trb *trb = td->first_trb; + + while (1) { + trb_to_noop(trb, TRB_TR_NOOP); + + /* flip cycle if asked to */ + if (flip_cycle && trb != td->first_trb && trb != td->last_trb) + trb->generic.field[3] ^= cpu_to_le32(TRB_CYCLE); + + if (trb == td->last_trb) + break; + + next_trb(xhci, ep_ring, &seg, &trb); + } +} + +/* + * Must be called with xhci->lock held in interrupt context, + * releases and re-acquires xhci->lock + */ +static void xhci_giveback_urb_in_irq(struct xhci_hcd *xhci, + struct xhci_td *cur_td, int status) +{ + struct urb *urb = cur_td->urb; + struct urb_priv *urb_priv = urb->hcpriv; + struct usb_hcd *hcd = bus_to_hcd(urb->dev->bus); + + if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) { + xhci_to_hcd(xhci)->self.bandwidth_isoc_reqs--; + if (xhci_to_hcd(xhci)->self.bandwidth_isoc_reqs == 0) { + if (xhci->quirks & XHCI_AMD_PLL_FIX) + usb_amd_quirk_pll_enable(); + } + } + xhci_urb_free_priv(urb_priv); + usb_hcd_unlink_urb_from_ep(hcd, urb); + trace_xhci_urb_giveback(urb); + usb_hcd_giveback_urb(hcd, urb, status); +} + +static void xhci_unmap_td_bounce_buffer(struct xhci_hcd *xhci, + struct xhci_ring *ring, struct xhci_td *td) +{ + struct device *dev = xhci_to_hcd(xhci)->self.sysdev; + struct xhci_segment *seg = td->bounce_seg; + struct urb *urb = td->urb; + size_t len; + + if (!ring || !seg || !urb) + return; + + if (usb_urb_dir_out(urb)) { + dma_unmap_single(dev, seg->bounce_dma, ring->bounce_buf_len, + DMA_TO_DEVICE); + return; + } + + dma_unmap_single(dev, seg->bounce_dma, ring->bounce_buf_len, + DMA_FROM_DEVICE); + /* for in tranfers we need to copy the data from bounce to sg */ + if (urb->num_sgs) { + len = sg_pcopy_from_buffer(urb->sg, urb->num_sgs, seg->bounce_buf, + seg->bounce_len, seg->bounce_offs); + if (len != seg->bounce_len) + xhci_warn(xhci, "WARN Wrong bounce buffer read length: %zu != %d\n", + len, seg->bounce_len); + } else { + memcpy(urb->transfer_buffer + seg->bounce_offs, seg->bounce_buf, + seg->bounce_len); + } + seg->bounce_len = 0; + seg->bounce_offs = 0; +} + +static int xhci_td_cleanup(struct xhci_hcd *xhci, struct xhci_td *td, + struct xhci_ring *ep_ring, int status) +{ + struct urb *urb = NULL; + + /* Clean up the endpoint's TD list */ + urb = td->urb; + + /* if a bounce buffer was used to align this td then unmap it */ + xhci_unmap_td_bounce_buffer(xhci, ep_ring, td); + + /* Do one last check of the actual transfer length. + * If the host controller said we transferred more data than the buffer + * length, urb->actual_length will be a very big number (since it's + * unsigned). Play it safe and say we didn't transfer anything. + */ + if (urb->actual_length > urb->transfer_buffer_length) { + xhci_warn(xhci, "URB req %u and actual %u transfer length mismatch\n", + urb->transfer_buffer_length, urb->actual_length); + urb->actual_length = 0; + status = 0; + } + /* TD might be removed from td_list if we are giving back a cancelled URB */ + if (!list_empty(&td->td_list)) + list_del_init(&td->td_list); + /* Giving back a cancelled URB, or if a slated TD completed anyway */ + if (!list_empty(&td->cancelled_td_list)) + list_del_init(&td->cancelled_td_list); + + inc_td_cnt(urb); + /* Giveback the urb when all the tds are completed */ + if (last_td_in_urb(td)) { + if ((urb->actual_length != urb->transfer_buffer_length && + (urb->transfer_flags & URB_SHORT_NOT_OK)) || + (status != 0 && !usb_endpoint_xfer_isoc(&urb->ep->desc))) + xhci_dbg(xhci, "Giveback URB %p, len = %d, expected = %d, status = %d\n", + urb, urb->actual_length, + urb->transfer_buffer_length, status); + + /* set isoc urb status to 0 just as EHCI, UHCI, and OHCI */ + if (usb_pipetype(urb->pipe) == PIPE_ISOCHRONOUS) + status = 0; + xhci_giveback_urb_in_irq(xhci, td, status); + } + + return 0; +} + + +/* Complete the cancelled URBs we unlinked from td_list. */ +static void xhci_giveback_invalidated_tds(struct xhci_virt_ep *ep) +{ + struct xhci_ring *ring; + struct xhci_td *td, *tmp_td; + + list_for_each_entry_safe(td, tmp_td, &ep->cancelled_td_list, + cancelled_td_list) { + + ring = xhci_urb_to_transfer_ring(ep->xhci, td->urb); + + if (td->cancel_status == TD_CLEARED) { + xhci_dbg(ep->xhci, "%s: Giveback cancelled URB %p TD\n", + __func__, td->urb); + xhci_td_cleanup(ep->xhci, td, ring, td->status); + } else { + xhci_dbg(ep->xhci, "%s: Keep cancelled URB %p TD as cancel_status is %d\n", + __func__, td->urb, td->cancel_status); + } + if (ep->xhci->xhc_state & XHCI_STATE_DYING) + return; + } +} + +static int xhci_reset_halted_ep(struct xhci_hcd *xhci, unsigned int slot_id, + unsigned int ep_index, enum xhci_ep_reset_type reset_type) +{ + struct xhci_command *command; + int ret = 0; + + command = xhci_alloc_command(xhci, false, GFP_ATOMIC); + if (!command) { + ret = -ENOMEM; + goto done; + } + + xhci_dbg(xhci, "%s-reset ep %u, slot %u\n", + (reset_type == EP_HARD_RESET) ? "Hard" : "Soft", + ep_index, slot_id); + + ret = xhci_queue_reset_ep(xhci, command, slot_id, ep_index, reset_type); +done: + if (ret) + xhci_err(xhci, "ERROR queuing reset endpoint for slot %d ep_index %d, %d\n", + slot_id, ep_index, ret); + return ret; +} + +static int xhci_handle_halted_endpoint(struct xhci_hcd *xhci, + struct xhci_virt_ep *ep, unsigned int stream_id, + struct xhci_td *td, + enum xhci_ep_reset_type reset_type) +{ + unsigned int slot_id = ep->vdev->slot_id; + int err; + + /* + * Avoid resetting endpoint if link is inactive. Can cause host hang. + * Device will be reset soon to recover the link so don't do anything + */ + if (ep->vdev->flags & VDEV_PORT_ERROR) + return -ENODEV; + + /* add td to cancelled list and let reset ep handler take care of it */ + if (reset_type == EP_HARD_RESET) { + ep->ep_state |= EP_HARD_CLEAR_TOGGLE; + if (td && list_empty(&td->cancelled_td_list)) { + list_add_tail(&td->cancelled_td_list, &ep->cancelled_td_list); + td->cancel_status = TD_HALTED; + } + } + + if (ep->ep_state & EP_HALTED) { + xhci_dbg(xhci, "Reset ep command for ep_index %d already pending\n", + ep->ep_index); + return 0; + } + + err = xhci_reset_halted_ep(xhci, slot_id, ep->ep_index, reset_type); + if (err) + return err; + + ep->ep_state |= EP_HALTED; + + xhci_ring_cmd_db(xhci); + + return 0; +} + +/* + * Fix up the ep ring first, so HW stops executing cancelled TDs. + * We have the xHCI lock, so nothing can modify this list until we drop it. + * We're also in the event handler, so we can't get re-interrupted if another + * Stop Endpoint command completes. + * + * only call this when ring is not in a running state + */ + +static int xhci_invalidate_cancelled_tds(struct xhci_virt_ep *ep) +{ + struct xhci_hcd *xhci; + struct xhci_td *td = NULL; + struct xhci_td *tmp_td = NULL; + struct xhci_td *cached_td = NULL; + struct xhci_ring *ring; + u64 hw_deq; + unsigned int slot_id = ep->vdev->slot_id; + int err; + + xhci = ep->xhci; + + list_for_each_entry_safe(td, tmp_td, &ep->cancelled_td_list, cancelled_td_list) { + xhci_dbg_trace(xhci, trace_xhci_dbg_cancel_urb, + "Removing canceled TD starting at 0x%llx (dma) in stream %u URB %p", + (unsigned long long)xhci_trb_virt_to_dma( + td->start_seg, td->first_trb), + td->urb->stream_id, td->urb); + list_del_init(&td->td_list); + ring = xhci_urb_to_transfer_ring(xhci, td->urb); + if (!ring) { + xhci_warn(xhci, "WARN Cancelled URB %p has invalid stream ID %u.\n", + td->urb, td->urb->stream_id); + continue; + } + /* + * If a ring stopped on the TD we need to cancel then we have to + * move the xHC endpoint ring dequeue pointer past this TD. + * Rings halted due to STALL may show hw_deq is past the stalled + * TD, but still require a set TR Deq command to flush xHC cache. + */ + hw_deq = xhci_get_hw_deq(xhci, ep->vdev, ep->ep_index, + td->urb->stream_id); + hw_deq &= ~0xf; + + if (td->cancel_status == TD_HALTED || + trb_in_td(xhci, td->start_seg, td->first_trb, td->last_trb, hw_deq, false)) { + switch (td->cancel_status) { + case TD_CLEARED: /* TD is already no-op */ + case TD_CLEARING_CACHE: /* set TR deq command already queued */ + break; + case TD_DIRTY: /* TD is cached, clear it */ + case TD_HALTED: + td->cancel_status = TD_CLEARING_CACHE; + if (cached_td) + /* FIXME stream case, several stopped rings */ + xhci_dbg(xhci, + "Move dq past stream %u URB %p instead of stream %u URB %p\n", + td->urb->stream_id, td->urb, + cached_td->urb->stream_id, cached_td->urb); + cached_td = td; + break; + } + } else { + td_to_noop(xhci, ring, td, false); + td->cancel_status = TD_CLEARED; + } + } + + /* If there's no need to move the dequeue pointer then we're done */ + if (!cached_td) + return 0; + + err = xhci_move_dequeue_past_td(xhci, slot_id, ep->ep_index, + cached_td->urb->stream_id, + cached_td); + if (err) { + /* Failed to move past cached td, just set cached TDs to no-op */ + list_for_each_entry_safe(td, tmp_td, &ep->cancelled_td_list, cancelled_td_list) { + if (td->cancel_status != TD_CLEARING_CACHE) + continue; + xhci_dbg(xhci, "Failed to clear cancelled cached URB %p, mark clear anyway\n", + td->urb); + td_to_noop(xhci, ring, td, false); + td->cancel_status = TD_CLEARED; + } + } + return 0; +} + +/* + * Returns the TD the endpoint ring halted on. + * Only call for non-running rings without streams. + */ +static struct xhci_td *find_halted_td(struct xhci_virt_ep *ep) +{ + struct xhci_td *td; + u64 hw_deq; + + if (!list_empty(&ep->ring->td_list)) { /* Not streams compatible */ + hw_deq = xhci_get_hw_deq(ep->xhci, ep->vdev, ep->ep_index, 0); + hw_deq &= ~0xf; + td = list_first_entry(&ep->ring->td_list, struct xhci_td, td_list); + if (trb_in_td(ep->xhci, td->start_seg, td->first_trb, + td->last_trb, hw_deq, false)) + return td; + } + return NULL; +} + +/* + * When we get a command completion for a Stop Endpoint Command, we need to + * unlink any cancelled TDs from the ring. There are two ways to do that: + * + * 1. If the HW was in the middle of processing the TD that needs to be + * cancelled, then we must move the ring's dequeue pointer past the last TRB + * in the TD with a Set Dequeue Pointer Command. + * 2. Otherwise, we turn all the TRBs in the TD into No-op TRBs (with the chain + * bit cleared) so that the HW will skip over them. + */ +static void xhci_handle_cmd_stop_ep(struct xhci_hcd *xhci, int slot_id, + union xhci_trb *trb, u32 comp_code) +{ + unsigned int ep_index; + struct xhci_virt_ep *ep; + struct xhci_ep_ctx *ep_ctx; + struct xhci_td *td = NULL; + enum xhci_ep_reset_type reset_type; + struct xhci_command *command; + int err; + + if (unlikely(TRB_TO_SUSPEND_PORT(le32_to_cpu(trb->generic.field[3])))) { + if (!xhci->devs[slot_id]) + xhci_warn(xhci, "Stop endpoint command completion for disabled slot %u\n", + slot_id); + return; + } + + ep_index = TRB_TO_EP_INDEX(le32_to_cpu(trb->generic.field[3])); + ep = xhci_get_virt_ep(xhci, slot_id, ep_index); + if (!ep) + return; + + ep_ctx = xhci_get_ep_ctx(xhci, ep->vdev->out_ctx, ep_index); + + trace_xhci_handle_cmd_stop_ep(ep_ctx); + + if (comp_code == COMP_CONTEXT_STATE_ERROR) { + /* + * If stop endpoint command raced with a halting endpoint we need to + * reset the host side endpoint first. + * If the TD we halted on isn't cancelled the TD should be given back + * with a proper error code, and the ring dequeue moved past the TD. + * If streams case we can't find hw_deq, or the TD we halted on so do a + * soft reset. + * + * Proper error code is unknown here, it would be -EPIPE if device side + * of enadpoit halted (aka STALL), and -EPROTO if not (transaction error) + * We use -EPROTO, if device is stalled it should return a stall error on + * next transfer, which then will return -EPIPE, and device side stall is + * noted and cleared by class driver. + */ + switch (GET_EP_CTX_STATE(ep_ctx)) { + case EP_STATE_HALTED: + xhci_dbg(xhci, "Stop ep completion raced with stall, reset ep\n"); + if (ep->ep_state & EP_HAS_STREAMS) { + reset_type = EP_SOFT_RESET; + } else { + reset_type = EP_HARD_RESET; + td = find_halted_td(ep); + if (td) + td->status = -EPROTO; + } + /* reset ep, reset handler cleans up cancelled tds */ + err = xhci_handle_halted_endpoint(xhci, ep, 0, td, + reset_type); + if (err) + break; + ep->ep_state &= ~EP_STOP_CMD_PENDING; + return; + case EP_STATE_RUNNING: + /* Race, HW handled stop ep cmd before ep was running */ + xhci_dbg(xhci, "Stop ep completion ctx error, ep is running\n"); + + command = xhci_alloc_command(xhci, false, GFP_ATOMIC); + if (!command) { + ep->ep_state &= ~EP_STOP_CMD_PENDING; + return; + } + xhci_queue_stop_endpoint(xhci, command, slot_id, ep_index, 0); + xhci_ring_cmd_db(xhci); + + return; + default: + break; + } + } + + /* will queue a set TR deq if stopped on a cancelled, uncleared TD */ + xhci_invalidate_cancelled_tds(ep); + ep->ep_state &= ~EP_STOP_CMD_PENDING; + + /* Otherwise ring the doorbell(s) to restart queued transfers */ + xhci_giveback_invalidated_tds(ep); + ring_doorbell_for_active_rings(xhci, slot_id, ep_index); +} + +static void xhci_kill_ring_urbs(struct xhci_hcd *xhci, struct xhci_ring *ring) +{ + struct xhci_td *cur_td; + struct xhci_td *tmp; + + list_for_each_entry_safe(cur_td, tmp, &ring->td_list, td_list) { + list_del_init(&cur_td->td_list); + + if (!list_empty(&cur_td->cancelled_td_list)) + list_del_init(&cur_td->cancelled_td_list); + + xhci_unmap_td_bounce_buffer(xhci, ring, cur_td); + + inc_td_cnt(cur_td->urb); + if (last_td_in_urb(cur_td)) + xhci_giveback_urb_in_irq(xhci, cur_td, -ESHUTDOWN); + } +} + +static void xhci_kill_endpoint_urbs(struct xhci_hcd *xhci, + int slot_id, int ep_index) +{ + struct xhci_td *cur_td; + struct xhci_td *tmp; + struct xhci_virt_ep *ep; + struct xhci_ring *ring; + + ep = xhci_get_virt_ep(xhci, slot_id, ep_index); + if (!ep) + return; + + if ((ep->ep_state & EP_HAS_STREAMS) || + (ep->ep_state & EP_GETTING_NO_STREAMS)) { + int stream_id; + + for (stream_id = 1; stream_id < ep->stream_info->num_streams; + stream_id++) { + ring = ep->stream_info->stream_rings[stream_id]; + if (!ring) + continue; + + xhci_dbg_trace(xhci, trace_xhci_dbg_cancel_urb, + "Killing URBs for slot ID %u, ep index %u, stream %u", + slot_id, ep_index, stream_id); + xhci_kill_ring_urbs(xhci, ring); + } + } else { + ring = ep->ring; + if (!ring) + return; + xhci_dbg_trace(xhci, trace_xhci_dbg_cancel_urb, + "Killing URBs for slot ID %u, ep index %u", + slot_id, ep_index); + xhci_kill_ring_urbs(xhci, ring); + } + + list_for_each_entry_safe(cur_td, tmp, &ep->cancelled_td_list, + cancelled_td_list) { + list_del_init(&cur_td->cancelled_td_list); + inc_td_cnt(cur_td->urb); + + if (last_td_in_urb(cur_td)) + xhci_giveback_urb_in_irq(xhci, cur_td, -ESHUTDOWN); + } +} + +/* + * host controller died, register read returns 0xffffffff + * Complete pending commands, mark them ABORTED. + * URBs need to be given back as usb core might be waiting with device locks + * held for the URBs to finish during device disconnect, blocking host remove. + * + * Call with xhci->lock held. + * lock is relased and re-acquired while giving back urb. + */ +void xhci_hc_died(struct xhci_hcd *xhci) +{ + int i, j; + + if (xhci->xhc_state & XHCI_STATE_DYING) + return; + + xhci_err(xhci, "xHCI host controller not responding, assume dead\n"); + xhci->xhc_state |= XHCI_STATE_DYING; + + xhci_cleanup_command_queue(xhci); + + /* return any pending urbs, remove may be waiting for them */ + for (i = 0; i <= HCS_MAX_SLOTS(xhci->hcs_params1); i++) { + if (!xhci->devs[i]) + continue; + for (j = 0; j < 31; j++) + xhci_kill_endpoint_urbs(xhci, i, j); + } + + /* inform usb core hc died if PCI remove isn't already handling it */ + if (!(xhci->xhc_state & XHCI_STATE_REMOVING)) + usb_hc_died(xhci_to_hcd(xhci)); +} + +static void update_ring_for_set_deq_completion(struct xhci_hcd *xhci, + struct xhci_virt_device *dev, + struct xhci_ring *ep_ring, + unsigned int ep_index) +{ + union xhci_trb *dequeue_temp; + int num_trbs_free_temp; + bool revert = false; + + num_trbs_free_temp = ep_ring->num_trbs_free; + dequeue_temp = ep_ring->dequeue; + + /* If we get two back-to-back stalls, and the first stalled transfer + * ends just before a link TRB, the dequeue pointer will be left on + * the link TRB by the code in the while loop. So we have to update + * the dequeue pointer one segment further, or we'll jump off + * the segment into la-la-land. + */ + if (trb_is_link(ep_ring->dequeue)) { + ep_ring->deq_seg = ep_ring->deq_seg->next; + ep_ring->dequeue = ep_ring->deq_seg->trbs; + } + + while (ep_ring->dequeue != dev->eps[ep_index].queued_deq_ptr) { + /* We have more usable TRBs */ + ep_ring->num_trbs_free++; + ep_ring->dequeue++; + if (trb_is_link(ep_ring->dequeue)) { + if (ep_ring->dequeue == + dev->eps[ep_index].queued_deq_ptr) + break; + ep_ring->deq_seg = ep_ring->deq_seg->next; + ep_ring->dequeue = ep_ring->deq_seg->trbs; + } + if (ep_ring->dequeue == dequeue_temp) { + revert = true; + break; + } + } + + if (revert) { + xhci_dbg(xhci, "Unable to find new dequeue pointer\n"); + ep_ring->num_trbs_free = num_trbs_free_temp; + } +} + +/* + * When we get a completion for a Set Transfer Ring Dequeue Pointer command, + * we need to clear the set deq pending flag in the endpoint ring state, so that + * the TD queueing code can ring the doorbell again. We also need to ring the + * endpoint doorbell to restart the ring, but only if there aren't more + * cancellations pending. + */ +static void xhci_handle_cmd_set_deq(struct xhci_hcd *xhci, int slot_id, + union xhci_trb *trb, u32 cmd_comp_code) +{ + unsigned int ep_index; + unsigned int stream_id; + struct xhci_ring *ep_ring; + struct xhci_virt_ep *ep; + struct xhci_ep_ctx *ep_ctx; + struct xhci_slot_ctx *slot_ctx; + struct xhci_td *td, *tmp_td; + + ep_index = TRB_TO_EP_INDEX(le32_to_cpu(trb->generic.field[3])); + stream_id = TRB_TO_STREAM_ID(le32_to_cpu(trb->generic.field[2])); + ep = xhci_get_virt_ep(xhci, slot_id, ep_index); + if (!ep) + return; + + ep_ring = xhci_virt_ep_to_ring(xhci, ep, stream_id); + if (!ep_ring) { + xhci_warn(xhci, "WARN Set TR deq ptr command for freed stream ID %u\n", + stream_id); + /* XXX: Harmless??? */ + goto cleanup; + } + + ep_ctx = xhci_get_ep_ctx(xhci, ep->vdev->out_ctx, ep_index); + slot_ctx = xhci_get_slot_ctx(xhci, ep->vdev->out_ctx); + trace_xhci_handle_cmd_set_deq(slot_ctx); + trace_xhci_handle_cmd_set_deq_ep(ep_ctx); + + if (cmd_comp_code != COMP_SUCCESS) { + unsigned int ep_state; + unsigned int slot_state; + + switch (cmd_comp_code) { + case COMP_TRB_ERROR: + xhci_warn(xhci, "WARN Set TR Deq Ptr cmd invalid because of stream ID configuration\n"); + break; + case COMP_CONTEXT_STATE_ERROR: + xhci_warn(xhci, "WARN Set TR Deq Ptr cmd failed due to incorrect slot or ep state.\n"); + ep_state = GET_EP_CTX_STATE(ep_ctx); + slot_state = le32_to_cpu(slot_ctx->dev_state); + slot_state = GET_SLOT_STATE(slot_state); + xhci_dbg_trace(xhci, trace_xhci_dbg_cancel_urb, + "Slot state = %u, EP state = %u", + slot_state, ep_state); + break; + case COMP_SLOT_NOT_ENABLED_ERROR: + xhci_warn(xhci, "WARN Set TR Deq Ptr cmd failed because slot %u was not enabled.\n", + slot_id); + break; + default: + xhci_warn(xhci, "WARN Set TR Deq Ptr cmd with unknown completion code of %u.\n", + cmd_comp_code); + break; + } + /* OK what do we do now? The endpoint state is hosed, and we + * should never get to this point if the synchronization between + * queueing, and endpoint state are correct. This might happen + * if the device gets disconnected after we've finished + * cancelling URBs, which might not be an error... + */ + } else { + u64 deq; + /* 4.6.10 deq ptr is written to the stream ctx for streams */ + if (ep->ep_state & EP_HAS_STREAMS) { + struct xhci_stream_ctx *ctx = + &ep->stream_info->stream_ctx_array[stream_id]; + deq = le64_to_cpu(ctx->stream_ring) & SCTX_DEQ_MASK; + } else { + deq = le64_to_cpu(ep_ctx->deq) & ~EP_CTX_CYCLE_MASK; + } + xhci_dbg_trace(xhci, trace_xhci_dbg_cancel_urb, + "Successful Set TR Deq Ptr cmd, deq = @%08llx", deq); + if (xhci_trb_virt_to_dma(ep->queued_deq_seg, + ep->queued_deq_ptr) == deq) { + /* Update the ring's dequeue segment and dequeue pointer + * to reflect the new position. + */ + update_ring_for_set_deq_completion(xhci, ep->vdev, + ep_ring, ep_index); + } else { + xhci_warn(xhci, "Mismatch between completed Set TR Deq Ptr command & xHCI internal state.\n"); + xhci_warn(xhci, "ep deq seg = %p, deq ptr = %p\n", + ep->queued_deq_seg, ep->queued_deq_ptr); + } + } + /* HW cached TDs cleared from cache, give them back */ + list_for_each_entry_safe(td, tmp_td, &ep->cancelled_td_list, + cancelled_td_list) { + ep_ring = xhci_urb_to_transfer_ring(ep->xhci, td->urb); + if (td->cancel_status == TD_CLEARING_CACHE) { + td->cancel_status = TD_CLEARED; + xhci_dbg(ep->xhci, "%s: Giveback cancelled URB %p TD\n", + __func__, td->urb); + xhci_td_cleanup(ep->xhci, td, ep_ring, td->status); + } else { + xhci_dbg(ep->xhci, "%s: Keep cancelled URB %p TD as cancel_status is %d\n", + __func__, td->urb, td->cancel_status); + } + } +cleanup: + ep->ep_state &= ~SET_DEQ_PENDING; + ep->queued_deq_seg = NULL; + ep->queued_deq_ptr = NULL; + /* Restart any rings with pending URBs */ + ring_doorbell_for_active_rings(xhci, slot_id, ep_index); +} + +static void xhci_handle_cmd_reset_ep(struct xhci_hcd *xhci, int slot_id, + union xhci_trb *trb, u32 cmd_comp_code) +{ + struct xhci_virt_ep *ep; + struct xhci_ep_ctx *ep_ctx; + unsigned int ep_index; + + ep_index = TRB_TO_EP_INDEX(le32_to_cpu(trb->generic.field[3])); + ep = xhci_get_virt_ep(xhci, slot_id, ep_index); + if (!ep) + return; + + ep_ctx = xhci_get_ep_ctx(xhci, ep->vdev->out_ctx, ep_index); + trace_xhci_handle_cmd_reset_ep(ep_ctx); + + /* This command will only fail if the endpoint wasn't halted, + * but we don't care. + */ + xhci_dbg_trace(xhci, trace_xhci_dbg_reset_ep, + "Ignoring reset ep completion code of %u", cmd_comp_code); + + /* Cleanup cancelled TDs as ep is stopped. May queue a Set TR Deq cmd */ + xhci_invalidate_cancelled_tds(ep); + + /* Clear our internal halted state */ + ep->ep_state &= ~EP_HALTED; + + xhci_giveback_invalidated_tds(ep); + + /* if this was a soft reset, then restart */ + if ((le32_to_cpu(trb->generic.field[3])) & TRB_TSP) + ring_doorbell_for_active_rings(xhci, slot_id, ep_index); +} + +static void xhci_handle_cmd_enable_slot(struct xhci_hcd *xhci, int slot_id, + struct xhci_command *command, u32 cmd_comp_code) +{ + if (cmd_comp_code == COMP_SUCCESS) + command->slot_id = slot_id; + else + command->slot_id = 0; +} + +static void xhci_handle_cmd_disable_slot(struct xhci_hcd *xhci, int slot_id) +{ + struct xhci_virt_device *virt_dev; + struct xhci_slot_ctx *slot_ctx; + + virt_dev = xhci->devs[slot_id]; + if (!virt_dev) + return; + + slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->out_ctx); + trace_xhci_handle_cmd_disable_slot(slot_ctx); + + if (xhci->quirks & XHCI_EP_LIMIT_QUIRK) + /* Delete default control endpoint resources */ + xhci_free_device_endpoint_resources(xhci, virt_dev, true); +} + +static void xhci_handle_cmd_config_ep(struct xhci_hcd *xhci, int slot_id, + u32 cmd_comp_code) +{ + struct xhci_virt_device *virt_dev; + struct xhci_input_control_ctx *ctrl_ctx; + struct xhci_ep_ctx *ep_ctx; + unsigned int ep_index; + u32 add_flags; + + /* + * Configure endpoint commands can come from the USB core configuration + * or alt setting changes, or when streams were being configured. + */ + + virt_dev = xhci->devs[slot_id]; + if (!virt_dev) + return; + ctrl_ctx = xhci_get_input_control_ctx(virt_dev->in_ctx); + if (!ctrl_ctx) { + xhci_warn(xhci, "Could not get input context, bad type.\n"); + return; + } + + add_flags = le32_to_cpu(ctrl_ctx->add_flags); + + /* Input ctx add_flags are the endpoint index plus one */ + ep_index = xhci_last_valid_endpoint(add_flags) - 1; + + ep_ctx = xhci_get_ep_ctx(xhci, virt_dev->out_ctx, ep_index); + trace_xhci_handle_cmd_config_ep(ep_ctx); + + return; +} + +static void xhci_handle_cmd_addr_dev(struct xhci_hcd *xhci, int slot_id) +{ + struct xhci_virt_device *vdev; + struct xhci_slot_ctx *slot_ctx; + + vdev = xhci->devs[slot_id]; + if (!vdev) + return; + slot_ctx = xhci_get_slot_ctx(xhci, vdev->out_ctx); + trace_xhci_handle_cmd_addr_dev(slot_ctx); +} + +static void xhci_handle_cmd_reset_dev(struct xhci_hcd *xhci, int slot_id) +{ + struct xhci_virt_device *vdev; + struct xhci_slot_ctx *slot_ctx; + + vdev = xhci->devs[slot_id]; + if (!vdev) { + xhci_warn(xhci, "Reset device command completion for disabled slot %u\n", + slot_id); + return; + } + slot_ctx = xhci_get_slot_ctx(xhci, vdev->out_ctx); + trace_xhci_handle_cmd_reset_dev(slot_ctx); + + xhci_dbg(xhci, "Completed reset device command.\n"); +} + +static void xhci_handle_cmd_nec_get_fw(struct xhci_hcd *xhci, + struct xhci_event_cmd *event) +{ + if (!(xhci->quirks & XHCI_NEC_HOST)) { + xhci_warn(xhci, "WARN NEC_GET_FW command on non-NEC host\n"); + return; + } + xhci_dbg_trace(xhci, trace_xhci_dbg_quirks, + "NEC firmware version %2x.%02x", + NEC_FW_MAJOR(le32_to_cpu(event->status)), + NEC_FW_MINOR(le32_to_cpu(event->status))); +} + +static void xhci_complete_del_and_free_cmd(struct xhci_command *cmd, u32 status) +{ + list_del(&cmd->cmd_list); + + if (cmd->completion) { + cmd->status = status; + complete(cmd->completion); + } else { + kfree(cmd); + } +} + +void xhci_cleanup_command_queue(struct xhci_hcd *xhci) +{ + struct xhci_command *cur_cmd, *tmp_cmd; + xhci->current_cmd = NULL; + list_for_each_entry_safe(cur_cmd, tmp_cmd, &xhci->cmd_list, cmd_list) + xhci_complete_del_and_free_cmd(cur_cmd, COMP_COMMAND_ABORTED); +} + +void xhci_handle_command_timeout(struct work_struct *work) +{ + struct xhci_hcd *xhci; + unsigned long flags; + char str[XHCI_MSG_MAX]; + u64 hw_ring_state; + u32 cmd_field3; + u32 usbsts; + + xhci = container_of(to_delayed_work(work), struct xhci_hcd, cmd_timer); + + spin_lock_irqsave(&xhci->lock, flags); + + /* + * If timeout work is pending, or current_cmd is NULL, it means we + * raced with command completion. Command is handled so just return. + */ + if (!xhci->current_cmd || delayed_work_pending(&xhci->cmd_timer)) { + spin_unlock_irqrestore(&xhci->lock, flags); + return; + } + + cmd_field3 = le32_to_cpu(xhci->current_cmd->command_trb->generic.field[3]); + usbsts = readl(&xhci->op_regs->status); + xhci_dbg(xhci, "Command timeout, USBSTS:%s\n", xhci_decode_usbsts(str, usbsts)); + + /* Bail out and tear down xhci if a stop endpoint command failed */ + if (TRB_FIELD_TO_TYPE(cmd_field3) == TRB_STOP_RING) { + struct xhci_virt_ep *ep; + + xhci_warn(xhci, "xHCI host not responding to stop endpoint command\n"); + + ep = xhci_get_virt_ep(xhci, TRB_TO_SLOT_ID(cmd_field3), + TRB_TO_EP_INDEX(cmd_field3)); + if (ep) + ep->ep_state &= ~EP_STOP_CMD_PENDING; + + xhci_halt(xhci); + xhci_hc_died(xhci); + goto time_out_completed; + } + + /* mark this command to be cancelled */ + xhci->current_cmd->status = COMP_COMMAND_ABORTED; + + /* Make sure command ring is running before aborting it */ + hw_ring_state = xhci_read_64(xhci, &xhci->op_regs->cmd_ring); + if (hw_ring_state == ~(u64)0) { + xhci_hc_died(xhci); + goto time_out_completed; + } + + if ((xhci->cmd_ring_state & CMD_RING_STATE_RUNNING) && + (hw_ring_state & CMD_RING_RUNNING)) { + /* Prevent new doorbell, and start command abort */ + xhci->cmd_ring_state = CMD_RING_STATE_ABORTED; + xhci_dbg(xhci, "Command timeout\n"); + xhci_abort_cmd_ring(xhci, flags); + goto time_out_completed; + } + + /* host removed. Bail out */ + if (xhci->xhc_state & XHCI_STATE_REMOVING) { + xhci_dbg(xhci, "host removed, ring start fail?\n"); + xhci_cleanup_command_queue(xhci); + + goto time_out_completed; + } + + /* command timeout on stopped ring, ring can't be aborted */ + xhci_dbg(xhci, "Command timeout on stopped ring\n"); + xhci_handle_stopped_cmd_ring(xhci, xhci->current_cmd); + +time_out_completed: + spin_unlock_irqrestore(&xhci->lock, flags); + return; +} + +static void handle_cmd_completion(struct xhci_hcd *xhci, + struct xhci_event_cmd *event) +{ + unsigned int slot_id = TRB_TO_SLOT_ID(le32_to_cpu(event->flags)); + u64 cmd_dma; + dma_addr_t cmd_dequeue_dma; + u32 cmd_comp_code; + union xhci_trb *cmd_trb; + struct xhci_command *cmd; + u32 cmd_type; + + if (slot_id >= MAX_HC_SLOTS) { + xhci_warn(xhci, "Invalid slot_id %u\n", slot_id); + return; + } + + cmd_dma = le64_to_cpu(event->cmd_trb); + cmd_trb = xhci->cmd_ring->dequeue; + + trace_xhci_handle_command(xhci->cmd_ring, &cmd_trb->generic); + + cmd_dequeue_dma = xhci_trb_virt_to_dma(xhci->cmd_ring->deq_seg, + cmd_trb); + /* + * Check whether the completion event is for our internal kept + * command. + */ + if (!cmd_dequeue_dma || cmd_dma != (u64)cmd_dequeue_dma) { + xhci_warn(xhci, + "ERROR mismatched command completion event\n"); + return; + } + + cmd = list_first_entry(&xhci->cmd_list, struct xhci_command, cmd_list); + + cancel_delayed_work(&xhci->cmd_timer); + + cmd_comp_code = GET_COMP_CODE(le32_to_cpu(event->status)); + + /* If CMD ring stopped we own the trbs between enqueue and dequeue */ + if (cmd_comp_code == COMP_COMMAND_RING_STOPPED) { + complete_all(&xhci->cmd_ring_stop_completion); + return; + } + + if (cmd->command_trb != xhci->cmd_ring->dequeue) { + xhci_err(xhci, + "Command completion event does not match command\n"); + return; + } + + /* + * Host aborted the command ring, check if the current command was + * supposed to be aborted, otherwise continue normally. + * The command ring is stopped now, but the xHC will issue a Command + * Ring Stopped event which will cause us to restart it. + */ + if (cmd_comp_code == COMP_COMMAND_ABORTED) { + xhci->cmd_ring_state = CMD_RING_STATE_STOPPED; + if (cmd->status == COMP_COMMAND_ABORTED) { + if (xhci->current_cmd == cmd) + xhci->current_cmd = NULL; + goto event_handled; + } + } + + cmd_type = TRB_FIELD_TO_TYPE(le32_to_cpu(cmd_trb->generic.field[3])); + switch (cmd_type) { + case TRB_ENABLE_SLOT: + xhci_handle_cmd_enable_slot(xhci, slot_id, cmd, cmd_comp_code); + break; + case TRB_DISABLE_SLOT: + xhci_handle_cmd_disable_slot(xhci, slot_id); + break; + case TRB_CONFIG_EP: + if (!cmd->completion) + xhci_handle_cmd_config_ep(xhci, slot_id, cmd_comp_code); + break; + case TRB_EVAL_CONTEXT: + break; + case TRB_ADDR_DEV: + xhci_handle_cmd_addr_dev(xhci, slot_id); + break; + case TRB_STOP_RING: + WARN_ON(slot_id != TRB_TO_SLOT_ID( + le32_to_cpu(cmd_trb->generic.field[3]))); + if (!cmd->completion) + xhci_handle_cmd_stop_ep(xhci, slot_id, cmd_trb, + cmd_comp_code); + break; + case TRB_SET_DEQ: + WARN_ON(slot_id != TRB_TO_SLOT_ID( + le32_to_cpu(cmd_trb->generic.field[3]))); + xhci_handle_cmd_set_deq(xhci, slot_id, cmd_trb, cmd_comp_code); + break; + case TRB_CMD_NOOP: + /* Is this an aborted command turned to NO-OP? */ + if (cmd->status == COMP_COMMAND_RING_STOPPED) + cmd_comp_code = COMP_COMMAND_RING_STOPPED; + break; + case TRB_RESET_EP: + WARN_ON(slot_id != TRB_TO_SLOT_ID( + le32_to_cpu(cmd_trb->generic.field[3]))); + xhci_handle_cmd_reset_ep(xhci, slot_id, cmd_trb, cmd_comp_code); + break; + case TRB_RESET_DEV: + /* SLOT_ID field in reset device cmd completion event TRB is 0. + * Use the SLOT_ID from the command TRB instead (xhci 4.6.11) + */ + slot_id = TRB_TO_SLOT_ID( + le32_to_cpu(cmd_trb->generic.field[3])); + xhci_handle_cmd_reset_dev(xhci, slot_id); + break; + case TRB_NEC_GET_FW: + xhci_handle_cmd_nec_get_fw(xhci, event); + break; + default: + /* Skip over unknown commands on the event ring */ + xhci_info(xhci, "INFO unknown command type %d\n", cmd_type); + break; + } + + /* restart timer if this wasn't the last command */ + if (!list_is_singular(&xhci->cmd_list)) { + xhci->current_cmd = list_first_entry(&cmd->cmd_list, + struct xhci_command, cmd_list); + xhci_mod_cmd_timer(xhci, XHCI_CMD_DEFAULT_TIMEOUT); + } else if (xhci->current_cmd == cmd) { + xhci->current_cmd = NULL; + } + +event_handled: + xhci_complete_del_and_free_cmd(cmd, cmd_comp_code); + + inc_deq(xhci, xhci->cmd_ring); +} + +static void handle_vendor_event(struct xhci_hcd *xhci, + union xhci_trb *event, u32 trb_type) +{ + xhci_dbg(xhci, "Vendor specific event TRB type = %u\n", trb_type); + if (trb_type == TRB_NEC_CMD_COMP && (xhci->quirks & XHCI_NEC_HOST)) + handle_cmd_completion(xhci, &event->event_cmd); +} + +static void handle_device_notification(struct xhci_hcd *xhci, + union xhci_trb *event) +{ + u32 slot_id; + struct usb_device *udev; + + slot_id = TRB_TO_SLOT_ID(le32_to_cpu(event->generic.field[3])); + if (!xhci->devs[slot_id]) { + xhci_warn(xhci, "Device Notification event for " + "unused slot %u\n", slot_id); + return; + } + + xhci_dbg(xhci, "Device Wake Notification event for slot ID %u\n", + slot_id); + udev = xhci->devs[slot_id]->udev; + if (udev && udev->parent) + usb_wakeup_notification(udev->parent, udev->portnum); +} + +/* + * Quirk hanlder for errata seen on Cavium ThunderX2 processor XHCI + * Controller. + * As per ThunderX2errata-129 USB 2 device may come up as USB 1 + * If a connection to a USB 1 device is followed by another connection + * to a USB 2 device. + * + * Reset the PHY after the USB device is disconnected if device speed + * is less than HCD_USB3. + * Retry the reset sequence max of 4 times checking the PLL lock status. + * + */ +static void xhci_cavium_reset_phy_quirk(struct xhci_hcd *xhci) +{ + struct usb_hcd *hcd = xhci_to_hcd(xhci); + u32 pll_lock_check; + u32 retry_count = 4; + + do { + /* Assert PHY reset */ + writel(0x6F, hcd->regs + 0x1048); + udelay(10); + /* De-assert the PHY reset */ + writel(0x7F, hcd->regs + 0x1048); + udelay(200); + pll_lock_check = readl(hcd->regs + 0x1070); + } while (!(pll_lock_check & 0x1) && --retry_count); +} + +static void handle_port_status(struct xhci_hcd *xhci, + union xhci_trb *event) +{ + struct usb_hcd *hcd; + u32 port_id; + u32 portsc, cmd_reg; + int max_ports; + int slot_id; + unsigned int hcd_portnum; + struct xhci_bus_state *bus_state; + bool bogus_port_status = false; + struct xhci_port *port; + + /* Port status change events always have a successful completion code */ + if (GET_COMP_CODE(le32_to_cpu(event->generic.field[2])) != COMP_SUCCESS) + xhci_warn(xhci, + "WARN: xHC returned failed port status event\n"); + + port_id = GET_PORT_ID(le32_to_cpu(event->generic.field[0])); + max_ports = HCS_MAX_PORTS(xhci->hcs_params1); + + if ((port_id <= 0) || (port_id > max_ports)) { + xhci_warn(xhci, "Port change event with invalid port ID %d\n", + port_id); + inc_deq(xhci, xhci->event_ring); + return; + } + + port = &xhci->hw_ports[port_id - 1]; + if (!port || !port->rhub || port->hcd_portnum == DUPLICATE_ENTRY) { + xhci_warn(xhci, "Port change event, no port for port ID %u\n", + port_id); + bogus_port_status = true; + goto cleanup; + } + + /* We might get interrupts after shared_hcd is removed */ + if (port->rhub == &xhci->usb3_rhub && xhci->shared_hcd == NULL) { + xhci_dbg(xhci, "ignore port event for removed USB3 hcd\n"); + bogus_port_status = true; + goto cleanup; + } + + hcd = port->rhub->hcd; + bus_state = &port->rhub->bus_state; + hcd_portnum = port->hcd_portnum; + portsc = readl(port->addr); + + xhci_dbg(xhci, "Port change event, %d-%d, id %d, portsc: 0x%x\n", + hcd->self.busnum, hcd_portnum + 1, port_id, portsc); + + trace_xhci_handle_port_status(hcd_portnum, portsc); + + if (hcd->state == HC_STATE_SUSPENDED) { + xhci_dbg(xhci, "resume root hub\n"); + usb_hcd_resume_root_hub(hcd); + } + + if (hcd->speed >= HCD_USB3 && + (portsc & PORT_PLS_MASK) == XDEV_INACTIVE) { + slot_id = xhci_find_slot_id_by_port(hcd, xhci, hcd_portnum + 1); + if (slot_id && xhci->devs[slot_id]) + xhci->devs[slot_id]->flags |= VDEV_PORT_ERROR; + } + + if ((portsc & PORT_PLC) && (portsc & PORT_PLS_MASK) == XDEV_RESUME) { + xhci_dbg(xhci, "port resume event for port %d\n", port_id); + + cmd_reg = readl(&xhci->op_regs->command); + if (!(cmd_reg & CMD_RUN)) { + xhci_warn(xhci, "xHC is not running.\n"); + goto cleanup; + } + + if (DEV_SUPERSPEED_ANY(portsc)) { + xhci_dbg(xhci, "remote wake SS port %d\n", port_id); + /* Set a flag to say the port signaled remote wakeup, + * so we can tell the difference between the end of + * device and host initiated resume. + */ + bus_state->port_remote_wakeup |= 1 << hcd_portnum; + xhci_test_and_clear_bit(xhci, port, PORT_PLC); + usb_hcd_start_port_resume(&hcd->self, hcd_portnum); + xhci_set_link_state(xhci, port, XDEV_U0); + /* Need to wait until the next link state change + * indicates the device is actually in U0. + */ + bogus_port_status = true; + goto cleanup; + } else if (!test_bit(hcd_portnum, &bus_state->resuming_ports)) { + xhci_dbg(xhci, "resume HS port %d\n", port_id); + bus_state->resume_done[hcd_portnum] = jiffies + + msecs_to_jiffies(USB_RESUME_TIMEOUT); + set_bit(hcd_portnum, &bus_state->resuming_ports); + /* Do the rest in GetPortStatus after resume time delay. + * Avoid polling roothub status before that so that a + * usb device auto-resume latency around ~40ms. + */ + set_bit(HCD_FLAG_POLL_RH, &hcd->flags); + mod_timer(&hcd->rh_timer, + bus_state->resume_done[hcd_portnum]); + usb_hcd_start_port_resume(&hcd->self, hcd_portnum); + bogus_port_status = true; + } + } + + if ((portsc & PORT_PLC) && + DEV_SUPERSPEED_ANY(portsc) && + ((portsc & PORT_PLS_MASK) == XDEV_U0 || + (portsc & PORT_PLS_MASK) == XDEV_U1 || + (portsc & PORT_PLS_MASK) == XDEV_U2)) { + xhci_dbg(xhci, "resume SS port %d finished\n", port_id); + complete(&bus_state->u3exit_done[hcd_portnum]); + /* We've just brought the device into U0/1/2 through either the + * Resume state after a device remote wakeup, or through the + * U3Exit state after a host-initiated resume. If it's a device + * initiated remote wake, don't pass up the link state change, + * so the roothub behavior is consistent with external + * USB 3.0 hub behavior. + */ + slot_id = xhci_find_slot_id_by_port(hcd, xhci, hcd_portnum + 1); + if (slot_id && xhci->devs[slot_id]) + xhci_ring_device(xhci, slot_id); + if (bus_state->port_remote_wakeup & (1 << hcd_portnum)) { + xhci_test_and_clear_bit(xhci, port, PORT_PLC); + usb_wakeup_notification(hcd->self.root_hub, + hcd_portnum + 1); + bogus_port_status = true; + goto cleanup; + } + } + + /* + * Check to see if xhci-hub.c is waiting on RExit to U0 transition (or + * RExit to a disconnect state). If so, let the driver know it's + * out of the RExit state. + */ + if (!DEV_SUPERSPEED_ANY(portsc) && hcd->speed < HCD_USB3 && + test_and_clear_bit(hcd_portnum, + &bus_state->rexit_ports)) { + complete(&bus_state->rexit_done[hcd_portnum]); + bogus_port_status = true; + goto cleanup; + } + + if (hcd->speed < HCD_USB3) { + xhci_test_and_clear_bit(xhci, port, PORT_PLC); + if ((xhci->quirks & XHCI_RESET_PLL_ON_DISCONNECT) && + (portsc & PORT_CSC) && !(portsc & PORT_CONNECT)) + xhci_cavium_reset_phy_quirk(xhci); + } + +cleanup: + /* Update event ring dequeue pointer before dropping the lock */ + inc_deq(xhci, xhci->event_ring); + + /* Don't make the USB core poll the roothub if we got a bad port status + * change event. Besides, at that point we can't tell which roothub + * (USB 2.0 or USB 3.0) to kick. + */ + if (bogus_port_status) + return; + + /* + * xHCI port-status-change events occur when the "or" of all the + * status-change bits in the portsc register changes from 0 to 1. + * New status changes won't cause an event if any other change + * bits are still set. When an event occurs, switch over to + * polling to avoid losing status changes. + */ + xhci_dbg(xhci, "%s: starting usb%d port polling.\n", + __func__, hcd->self.busnum); + set_bit(HCD_FLAG_POLL_RH, &hcd->flags); + spin_unlock(&xhci->lock); + /* Pass this up to the core */ + usb_hcd_poll_rh_status(hcd); + spin_lock(&xhci->lock); +} + +/* + * This TD is defined by the TRBs starting at start_trb in start_seg and ending + * at end_trb, which may be in another segment. If the suspect DMA address is a + * TRB in this TD, this function returns that TRB's segment. Otherwise it + * returns 0. + */ +struct xhci_segment *trb_in_td(struct xhci_hcd *xhci, + struct xhci_segment *start_seg, + union xhci_trb *start_trb, + union xhci_trb *end_trb, + dma_addr_t suspect_dma, + bool debug) +{ + dma_addr_t start_dma; + dma_addr_t end_seg_dma; + dma_addr_t end_trb_dma; + struct xhci_segment *cur_seg; + + start_dma = xhci_trb_virt_to_dma(start_seg, start_trb); + cur_seg = start_seg; + + do { + if (start_dma == 0) + return NULL; + /* We may get an event for a Link TRB in the middle of a TD */ + end_seg_dma = xhci_trb_virt_to_dma(cur_seg, + &cur_seg->trbs[TRBS_PER_SEGMENT - 1]); + /* If the end TRB isn't in this segment, this is set to 0 */ + end_trb_dma = xhci_trb_virt_to_dma(cur_seg, end_trb); + + if (debug) + xhci_warn(xhci, + "Looking for event-dma %016llx trb-start %016llx trb-end %016llx seg-start %016llx seg-end %016llx\n", + (unsigned long long)suspect_dma, + (unsigned long long)start_dma, + (unsigned long long)end_trb_dma, + (unsigned long long)cur_seg->dma, + (unsigned long long)end_seg_dma); + + if (end_trb_dma > 0) { + /* The end TRB is in this segment, so suspect should be here */ + if (start_dma <= end_trb_dma) { + if (suspect_dma >= start_dma && suspect_dma <= end_trb_dma) + return cur_seg; + } else { + /* Case for one segment with + * a TD wrapped around to the top + */ + if ((suspect_dma >= start_dma && + suspect_dma <= end_seg_dma) || + (suspect_dma >= cur_seg->dma && + suspect_dma <= end_trb_dma)) + return cur_seg; + } + return NULL; + } else { + /* Might still be somewhere in this segment */ + if (suspect_dma >= start_dma && suspect_dma <= end_seg_dma) + return cur_seg; + } + cur_seg = cur_seg->next; + start_dma = xhci_trb_virt_to_dma(cur_seg, &cur_seg->trbs[0]); + } while (cur_seg != start_seg); + + return NULL; +} + +static void xhci_clear_hub_tt_buffer(struct xhci_hcd *xhci, struct xhci_td *td, + struct xhci_virt_ep *ep) +{ + /* + * As part of low/full-speed endpoint-halt processing + * we must clear the TT buffer (USB 2.0 specification 11.17.5). + */ + if (td->urb->dev->tt && !usb_pipeint(td->urb->pipe) && + (td->urb->dev->tt->hub != xhci_to_hcd(xhci)->self.root_hub) && + !(ep->ep_state & EP_CLEARING_TT)) { + ep->ep_state |= EP_CLEARING_TT; + td->urb->ep->hcpriv = td->urb->dev; + if (usb_hub_clear_tt_buffer(td->urb)) + ep->ep_state &= ~EP_CLEARING_TT; + } +} + +/* Check if an error has halted the endpoint ring. The class driver will + * cleanup the halt for a non-default control endpoint if we indicate a stall. + * However, a babble and other errors also halt the endpoint ring, and the class + * driver won't clear the halt in that case, so we need to issue a Set Transfer + * Ring Dequeue Pointer command manually. + */ +static int xhci_requires_manual_halt_cleanup(struct xhci_hcd *xhci, + struct xhci_ep_ctx *ep_ctx, + unsigned int trb_comp_code) +{ + /* TRB completion codes that may require a manual halt cleanup */ + if (trb_comp_code == COMP_USB_TRANSACTION_ERROR || + trb_comp_code == COMP_BABBLE_DETECTED_ERROR || + trb_comp_code == COMP_SPLIT_TRANSACTION_ERROR) + /* The 0.95 spec says a babbling control endpoint + * is not halted. The 0.96 spec says it is. Some HW + * claims to be 0.95 compliant, but it halts the control + * endpoint anyway. Check if a babble halted the + * endpoint. + */ + if (GET_EP_CTX_STATE(ep_ctx) == EP_STATE_HALTED) + return 1; + + return 0; +} + +int xhci_is_vendor_info_code(struct xhci_hcd *xhci, unsigned int trb_comp_code) +{ + if (trb_comp_code >= 224 && trb_comp_code <= 255) { + /* Vendor defined "informational" completion code, + * treat as not-an-error. + */ + xhci_dbg(xhci, "Vendor defined info completion code %u\n", + trb_comp_code); + xhci_dbg(xhci, "Treating code as success.\n"); + return 1; + } + return 0; +} + +static int finish_td(struct xhci_hcd *xhci, struct xhci_virt_ep *ep, + struct xhci_ring *ep_ring, struct xhci_td *td, + u32 trb_comp_code) +{ + struct xhci_ep_ctx *ep_ctx; + int trbs_freed; + + ep_ctx = xhci_get_ep_ctx(xhci, ep->vdev->out_ctx, ep->ep_index); + + switch (trb_comp_code) { + case COMP_STOPPED_LENGTH_INVALID: + case COMP_STOPPED_SHORT_PACKET: + case COMP_STOPPED: + /* + * The "Stop Endpoint" completion will take care of any + * stopped TDs. A stopped TD may be restarted, so don't update + * the ring dequeue pointer or take this TD off any lists yet. + */ + return 0; + case COMP_USB_TRANSACTION_ERROR: + case COMP_BABBLE_DETECTED_ERROR: + case COMP_SPLIT_TRANSACTION_ERROR: + /* + * If endpoint context state is not halted we might be + * racing with a reset endpoint command issued by a unsuccessful + * stop endpoint completion (context error). In that case the + * td should be on the cancelled list, and EP_HALTED flag set. + * + * Or then it's not halted due to the 0.95 spec stating that a + * babbling control endpoint should not halt. The 0.96 spec + * again says it should. Some HW claims to be 0.95 compliant, + * but it halts the control endpoint anyway. + */ + if (GET_EP_CTX_STATE(ep_ctx) != EP_STATE_HALTED) { + /* + * If EP_HALTED is set and TD is on the cancelled list + * the TD and dequeue pointer will be handled by reset + * ep command completion + */ + if ((ep->ep_state & EP_HALTED) && + !list_empty(&td->cancelled_td_list)) { + xhci_dbg(xhci, "Already resolving halted ep for 0x%llx\n", + (unsigned long long)xhci_trb_virt_to_dma( + td->start_seg, td->first_trb)); + return 0; + } + /* endpoint not halted, don't reset it */ + break; + } + /* Almost same procedure as for STALL_ERROR below */ + xhci_clear_hub_tt_buffer(xhci, td, ep); + xhci_handle_halted_endpoint(xhci, ep, ep_ring->stream_id, td, + EP_HARD_RESET); + return 0; + case COMP_STALL_ERROR: + /* + * xhci internal endpoint state will go to a "halt" state for + * any stall, including default control pipe protocol stall. + * To clear the host side halt we need to issue a reset endpoint + * command, followed by a set dequeue command to move past the + * TD. + * Class drivers clear the device side halt from a functional + * stall later. Hub TT buffer should only be cleared for FS/LS + * devices behind HS hubs for functional stalls. + */ + if (ep->ep_index != 0) + xhci_clear_hub_tt_buffer(xhci, td, ep); + + xhci_handle_halted_endpoint(xhci, ep, ep_ring->stream_id, td, + EP_HARD_RESET); + + return 0; /* xhci_handle_halted_endpoint marked td cancelled */ + default: + break; + } + + /* Update ring dequeue pointer */ + trbs_freed = xhci_num_trbs_to(ep_ring->deq_seg, ep_ring->dequeue, + td->last_trb_seg, td->last_trb, + ep_ring->num_segs); + if (trbs_freed < 0) + xhci_dbg(xhci, "Failed to count freed trbs at TD finish\n"); + else + ep_ring->num_trbs_free += trbs_freed; + ep_ring->dequeue = td->last_trb; + ep_ring->deq_seg = td->last_trb_seg; + inc_deq(xhci, ep_ring); + + return xhci_td_cleanup(xhci, td, ep_ring, td->status); +} + +/* sum trb lengths from ring dequeue up to stop_trb, _excluding_ stop_trb */ +static int sum_trb_lengths(struct xhci_hcd *xhci, struct xhci_ring *ring, + union xhci_trb *stop_trb) +{ + u32 sum; + union xhci_trb *trb = ring->dequeue; + struct xhci_segment *seg = ring->deq_seg; + + for (sum = 0; trb != stop_trb; next_trb(xhci, ring, &seg, &trb)) { + if (!trb_is_noop(trb) && !trb_is_link(trb)) + sum += TRB_LEN(le32_to_cpu(trb->generic.field[2])); + } + return sum; +} + +/* + * Process control tds, update urb status and actual_length. + */ +static int process_ctrl_td(struct xhci_hcd *xhci, struct xhci_virt_ep *ep, + struct xhci_ring *ep_ring, struct xhci_td *td, + union xhci_trb *ep_trb, struct xhci_transfer_event *event) +{ + struct xhci_ep_ctx *ep_ctx; + u32 trb_comp_code; + u32 remaining, requested; + u32 trb_type; + + trb_type = TRB_FIELD_TO_TYPE(le32_to_cpu(ep_trb->generic.field[3])); + ep_ctx = xhci_get_ep_ctx(xhci, ep->vdev->out_ctx, ep->ep_index); + trb_comp_code = GET_COMP_CODE(le32_to_cpu(event->transfer_len)); + requested = td->urb->transfer_buffer_length; + remaining = EVENT_TRB_LEN(le32_to_cpu(event->transfer_len)); + + switch (trb_comp_code) { + case COMP_SUCCESS: + if (trb_type != TRB_STATUS) { + xhci_warn(xhci, "WARN: Success on ctrl %s TRB without IOC set?\n", + (trb_type == TRB_DATA) ? "data" : "setup"); + td->status = -ESHUTDOWN; + break; + } + td->status = 0; + break; + case COMP_SHORT_PACKET: + td->status = 0; + break; + case COMP_STOPPED_SHORT_PACKET: + if (trb_type == TRB_DATA || trb_type == TRB_NORMAL) + td->urb->actual_length = remaining; + else + xhci_warn(xhci, "WARN: Stopped Short Packet on ctrl setup or status TRB\n"); + goto finish_td; + case COMP_STOPPED: + switch (trb_type) { + case TRB_SETUP: + td->urb->actual_length = 0; + goto finish_td; + case TRB_DATA: + case TRB_NORMAL: + td->urb->actual_length = requested - remaining; + goto finish_td; + case TRB_STATUS: + td->urb->actual_length = requested; + goto finish_td; + default: + xhci_warn(xhci, "WARN: unexpected TRB Type %d\n", + trb_type); + goto finish_td; + } + case COMP_STOPPED_LENGTH_INVALID: + goto finish_td; + default: + if (!xhci_requires_manual_halt_cleanup(xhci, + ep_ctx, trb_comp_code)) + break; + xhci_dbg(xhci, "TRB error %u, halted endpoint index = %u\n", + trb_comp_code, ep->ep_index); + fallthrough; + case COMP_STALL_ERROR: + /* Did we transfer part of the data (middle) phase? */ + if (trb_type == TRB_DATA || trb_type == TRB_NORMAL) + td->urb->actual_length = requested - remaining; + else if (!td->urb_length_set) + td->urb->actual_length = 0; + goto finish_td; + } + + /* stopped at setup stage, no data transferred */ + if (trb_type == TRB_SETUP) + goto finish_td; + + /* + * if on data stage then update the actual_length of the URB and flag it + * as set, so it won't be overwritten in the event for the last TRB. + */ + if (trb_type == TRB_DATA || + trb_type == TRB_NORMAL) { + td->urb_length_set = true; + td->urb->actual_length = requested - remaining; + xhci_dbg(xhci, "Waiting for status stage event\n"); + return 0; + } + + /* at status stage */ + if (!td->urb_length_set) + td->urb->actual_length = requested; + +finish_td: + return finish_td(xhci, ep, ep_ring, td, trb_comp_code); +} + +/* + * Process isochronous tds, update urb packet status and actual_length. + */ +static int process_isoc_td(struct xhci_hcd *xhci, struct xhci_virt_ep *ep, + struct xhci_ring *ep_ring, struct xhci_td *td, + union xhci_trb *ep_trb, struct xhci_transfer_event *event) +{ + struct urb_priv *urb_priv; + int idx; + struct usb_iso_packet_descriptor *frame; + u32 trb_comp_code; + bool sum_trbs_for_length = false; + u32 remaining, requested, ep_trb_len; + int short_framestatus; + + trb_comp_code = GET_COMP_CODE(le32_to_cpu(event->transfer_len)); + urb_priv = td->urb->hcpriv; + idx = urb_priv->num_tds_done; + frame = &td->urb->iso_frame_desc[idx]; + requested = frame->length; + remaining = EVENT_TRB_LEN(le32_to_cpu(event->transfer_len)); + ep_trb_len = TRB_LEN(le32_to_cpu(ep_trb->generic.field[2])); + short_framestatus = td->urb->transfer_flags & URB_SHORT_NOT_OK ? + -EREMOTEIO : 0; + + /* handle completion code */ + switch (trb_comp_code) { + case COMP_SUCCESS: + if (remaining) { + frame->status = short_framestatus; + if (xhci->quirks & XHCI_TRUST_TX_LENGTH) + sum_trbs_for_length = true; + break; + } + frame->status = 0; + break; + case COMP_SHORT_PACKET: + frame->status = short_framestatus; + sum_trbs_for_length = true; + break; + case COMP_BANDWIDTH_OVERRUN_ERROR: + frame->status = -ECOMM; + break; + case COMP_ISOCH_BUFFER_OVERRUN: + case COMP_BABBLE_DETECTED_ERROR: + frame->status = -EOVERFLOW; + break; + case COMP_INCOMPATIBLE_DEVICE_ERROR: + case COMP_STALL_ERROR: + frame->status = -EPROTO; + break; + case COMP_USB_TRANSACTION_ERROR: + frame->status = -EPROTO; + if (ep_trb != td->last_trb) + return 0; + break; + case COMP_STOPPED: + sum_trbs_for_length = true; + break; + case COMP_STOPPED_SHORT_PACKET: + /* field normally containing residue now contains tranferred */ + frame->status = short_framestatus; + requested = remaining; + break; + case COMP_STOPPED_LENGTH_INVALID: + requested = 0; + remaining = 0; + break; + default: + sum_trbs_for_length = true; + frame->status = -1; + break; + } + + if (sum_trbs_for_length) + frame->actual_length = sum_trb_lengths(xhci, ep->ring, ep_trb) + + ep_trb_len - remaining; + else + frame->actual_length = requested; + + td->urb->actual_length += frame->actual_length; + + return finish_td(xhci, ep, ep_ring, td, trb_comp_code); +} + +static int skip_isoc_td(struct xhci_hcd *xhci, struct xhci_td *td, + struct xhci_virt_ep *ep, int status) +{ + struct urb_priv *urb_priv; + struct usb_iso_packet_descriptor *frame; + int idx; + + urb_priv = td->urb->hcpriv; + idx = urb_priv->num_tds_done; + frame = &td->urb->iso_frame_desc[idx]; + + /* The transfer is partly done. */ + frame->status = -EXDEV; + + /* calc actual length */ + frame->actual_length = 0; + + /* Update ring dequeue pointer */ + ep->ring->dequeue = td->last_trb; + ep->ring->deq_seg = td->last_trb_seg; + ep->ring->num_trbs_free += td->num_trbs - 1; + inc_deq(xhci, ep->ring); + + return xhci_td_cleanup(xhci, td, ep->ring, status); +} + +/* + * Process bulk and interrupt tds, update urb status and actual_length. + */ +static int process_bulk_intr_td(struct xhci_hcd *xhci, struct xhci_virt_ep *ep, + struct xhci_ring *ep_ring, struct xhci_td *td, + union xhci_trb *ep_trb, struct xhci_transfer_event *event) +{ + struct xhci_slot_ctx *slot_ctx; + u32 trb_comp_code; + u32 remaining, requested, ep_trb_len; + + slot_ctx = xhci_get_slot_ctx(xhci, ep->vdev->out_ctx); + trb_comp_code = GET_COMP_CODE(le32_to_cpu(event->transfer_len)); + remaining = EVENT_TRB_LEN(le32_to_cpu(event->transfer_len)); + ep_trb_len = TRB_LEN(le32_to_cpu(ep_trb->generic.field[2])); + requested = td->urb->transfer_buffer_length; + + switch (trb_comp_code) { + case COMP_SUCCESS: + ep->err_count = 0; + /* handle success with untransferred data as short packet */ + if (ep_trb != td->last_trb || remaining) { + xhci_warn(xhci, "WARN Successful completion on short TX\n"); + xhci_dbg(xhci, "ep %#x - asked for %d bytes, %d bytes untransferred\n", + td->urb->ep->desc.bEndpointAddress, + requested, remaining); + } + td->status = 0; + break; + case COMP_SHORT_PACKET: + xhci_dbg(xhci, "ep %#x - asked for %d bytes, %d bytes untransferred\n", + td->urb->ep->desc.bEndpointAddress, + requested, remaining); + td->status = 0; + break; + case COMP_STOPPED_SHORT_PACKET: + td->urb->actual_length = remaining; + goto finish_td; + case COMP_STOPPED_LENGTH_INVALID: + /* stopped on ep trb with invalid length, exclude it */ + ep_trb_len = 0; + remaining = 0; + break; + case COMP_USB_TRANSACTION_ERROR: + if (xhci->quirks & XHCI_NO_SOFT_RETRY || + (ep->err_count++ > MAX_SOFT_RETRY) || + le32_to_cpu(slot_ctx->tt_info) & TT_SLOT) + break; + + td->status = 0; + + xhci_handle_halted_endpoint(xhci, ep, ep_ring->stream_id, td, + EP_SOFT_RESET); + return 0; + default: + /* do nothing */ + break; + } + + if (ep_trb == td->last_trb) + td->urb->actual_length = requested - remaining; + else + td->urb->actual_length = + sum_trb_lengths(xhci, ep_ring, ep_trb) + + ep_trb_len - remaining; +finish_td: + if (remaining > requested) { + xhci_warn(xhci, "bad transfer trb length %d in event trb\n", + remaining); + td->urb->actual_length = 0; + } + + return finish_td(xhci, ep, ep_ring, td, trb_comp_code); +} + +/* + * If this function returns an error condition, it means it got a Transfer + * event with a corrupted Slot ID, Endpoint ID, or TRB DMA address. + * At this point, the host controller is probably hosed and should be reset. + */ +static int handle_tx_event(struct xhci_hcd *xhci, + struct xhci_transfer_event *event) +{ + struct xhci_virt_ep *ep; + struct xhci_ring *ep_ring; + unsigned int slot_id; + int ep_index; + struct xhci_td *td = NULL; + dma_addr_t ep_trb_dma; + struct xhci_segment *ep_seg; + union xhci_trb *ep_trb; + int status = -EINPROGRESS; + struct xhci_ep_ctx *ep_ctx; + struct list_head *tmp; + u32 trb_comp_code; + int td_num = 0; + bool handling_skipped_tds = false; + + slot_id = TRB_TO_SLOT_ID(le32_to_cpu(event->flags)); + ep_index = TRB_TO_EP_ID(le32_to_cpu(event->flags)) - 1; + trb_comp_code = GET_COMP_CODE(le32_to_cpu(event->transfer_len)); + ep_trb_dma = le64_to_cpu(event->buffer); + + ep = xhci_get_virt_ep(xhci, slot_id, ep_index); + if (!ep) { + xhci_err(xhci, "ERROR Invalid Transfer event\n"); + goto err_out; + } + + ep_ring = xhci_dma_to_transfer_ring(ep, ep_trb_dma); + ep_ctx = xhci_get_ep_ctx(xhci, ep->vdev->out_ctx, ep_index); + + if (GET_EP_CTX_STATE(ep_ctx) == EP_STATE_DISABLED) { + xhci_err(xhci, + "ERROR Transfer event for disabled endpoint slot %u ep %u\n", + slot_id, ep_index); + goto err_out; + } + + /* Some transfer events don't always point to a trb, see xhci 4.17.4 */ + if (!ep_ring) { + switch (trb_comp_code) { + case COMP_STALL_ERROR: + case COMP_USB_TRANSACTION_ERROR: + case COMP_INVALID_STREAM_TYPE_ERROR: + case COMP_INVALID_STREAM_ID_ERROR: + xhci_dbg(xhci, "Stream transaction error ep %u no id\n", + ep_index); + if (ep->err_count++ > MAX_SOFT_RETRY) + xhci_handle_halted_endpoint(xhci, ep, 0, NULL, + EP_HARD_RESET); + else + xhci_handle_halted_endpoint(xhci, ep, 0, NULL, + EP_SOFT_RESET); + goto cleanup; + case COMP_RING_UNDERRUN: + case COMP_RING_OVERRUN: + case COMP_STOPPED_LENGTH_INVALID: + goto cleanup; + default: + xhci_err(xhci, "ERROR Transfer event for unknown stream ring slot %u ep %u\n", + slot_id, ep_index); + goto err_out; + } + } + + /* Count current td numbers if ep->skip is set */ + if (ep->skip) { + list_for_each(tmp, &ep_ring->td_list) + td_num++; + } + + /* Look for common error cases */ + switch (trb_comp_code) { + /* Skip codes that require special handling depending on + * transfer type + */ + case COMP_SUCCESS: + if (EVENT_TRB_LEN(le32_to_cpu(event->transfer_len)) == 0) + break; + if (xhci->quirks & XHCI_TRUST_TX_LENGTH || + ep_ring->last_td_was_short) + trb_comp_code = COMP_SHORT_PACKET; + else + xhci_warn_ratelimited(xhci, + "WARN Successful completion on short TX for slot %u ep %u: needs XHCI_TRUST_TX_LENGTH quirk?\n", + slot_id, ep_index); + break; + case COMP_SHORT_PACKET: + break; + /* Completion codes for endpoint stopped state */ + case COMP_STOPPED: + xhci_dbg(xhci, "Stopped on Transfer TRB for slot %u ep %u\n", + slot_id, ep_index); + break; + case COMP_STOPPED_LENGTH_INVALID: + xhci_dbg(xhci, + "Stopped on No-op or Link TRB for slot %u ep %u\n", + slot_id, ep_index); + break; + case COMP_STOPPED_SHORT_PACKET: + xhci_dbg(xhci, + "Stopped with short packet transfer detected for slot %u ep %u\n", + slot_id, ep_index); + break; + /* Completion codes for endpoint halted state */ + case COMP_STALL_ERROR: + xhci_dbg(xhci, "Stalled endpoint for slot %u ep %u\n", slot_id, + ep_index); + status = -EPIPE; + break; + case COMP_SPLIT_TRANSACTION_ERROR: + xhci_dbg(xhci, "Split transaction error for slot %u ep %u\n", + slot_id, ep_index); + status = -EPROTO; + break; + case COMP_USB_TRANSACTION_ERROR: + xhci_dbg(xhci, "Transfer error for slot %u ep %u on endpoint\n", + slot_id, ep_index); + status = -EPROTO; + break; + case COMP_BABBLE_DETECTED_ERROR: + xhci_dbg(xhci, "Babble error for slot %u ep %u on endpoint\n", + slot_id, ep_index); + status = -EOVERFLOW; + break; + /* Completion codes for endpoint error state */ + case COMP_TRB_ERROR: + xhci_warn(xhci, + "WARN: TRB error for slot %u ep %u on endpoint\n", + slot_id, ep_index); + status = -EILSEQ; + break; + /* completion codes not indicating endpoint state change */ + case COMP_DATA_BUFFER_ERROR: + xhci_warn(xhci, + "WARN: HC couldn't access mem fast enough for slot %u ep %u\n", + slot_id, ep_index); + status = -ENOSR; + break; + case COMP_BANDWIDTH_OVERRUN_ERROR: + xhci_warn(xhci, + "WARN: bandwidth overrun event for slot %u ep %u on endpoint\n", + slot_id, ep_index); + break; + case COMP_ISOCH_BUFFER_OVERRUN: + xhci_warn(xhci, + "WARN: buffer overrun event for slot %u ep %u on endpoint", + slot_id, ep_index); + break; + case COMP_RING_UNDERRUN: + /* + * When the Isoch ring is empty, the xHC will generate + * a Ring Overrun Event for IN Isoch endpoint or Ring + * Underrun Event for OUT Isoch endpoint. + */ + xhci_dbg(xhci, "underrun event on endpoint\n"); + if (!list_empty(&ep_ring->td_list)) + xhci_dbg(xhci, "Underrun Event for slot %d ep %d " + "still with TDs queued?\n", + TRB_TO_SLOT_ID(le32_to_cpu(event->flags)), + ep_index); + goto cleanup; + case COMP_RING_OVERRUN: + xhci_dbg(xhci, "overrun event on endpoint\n"); + if (!list_empty(&ep_ring->td_list)) + xhci_dbg(xhci, "Overrun Event for slot %d ep %d " + "still with TDs queued?\n", + TRB_TO_SLOT_ID(le32_to_cpu(event->flags)), + ep_index); + goto cleanup; + case COMP_MISSED_SERVICE_ERROR: + /* + * When encounter missed service error, one or more isoc tds + * may be missed by xHC. + * Set skip flag of the ep_ring; Complete the missed tds as + * short transfer when process the ep_ring next time. + */ + ep->skip = true; + xhci_dbg(xhci, + "Miss service interval error for slot %u ep %u, set skip flag\n", + slot_id, ep_index); + goto cleanup; + case COMP_NO_PING_RESPONSE_ERROR: + ep->skip = true; + xhci_dbg(xhci, + "No Ping response error for slot %u ep %u, Skip one Isoc TD\n", + slot_id, ep_index); + goto cleanup; + + case COMP_INCOMPATIBLE_DEVICE_ERROR: + /* needs disable slot command to recover */ + xhci_warn(xhci, + "WARN: detect an incompatible device for slot %u ep %u", + slot_id, ep_index); + status = -EPROTO; + break; + default: + if (xhci_is_vendor_info_code(xhci, trb_comp_code)) { + status = 0; + break; + } + xhci_warn(xhci, + "ERROR Unknown event condition %u for slot %u ep %u , HC probably busted\n", + trb_comp_code, slot_id, ep_index); + goto cleanup; + } + + do { + /* This TRB should be in the TD at the head of this ring's + * TD list. + */ + if (list_empty(&ep_ring->td_list)) { + /* + * Don't print wanings if it's due to a stopped endpoint + * generating an extra completion event if the device + * was suspended. Or, a event for the last TRB of a + * short TD we already got a short event for. + * The short TD is already removed from the TD list. + */ + + if (!(trb_comp_code == COMP_STOPPED || + trb_comp_code == COMP_STOPPED_LENGTH_INVALID || + ep_ring->last_td_was_short)) { + xhci_warn(xhci, "WARN Event TRB for slot %d ep %d with no TDs queued?\n", + TRB_TO_SLOT_ID(le32_to_cpu(event->flags)), + ep_index); + } + if (ep->skip) { + ep->skip = false; + xhci_dbg(xhci, "td_list is empty while skip flag set. Clear skip flag for slot %u ep %u.\n", + slot_id, ep_index); + } + if (trb_comp_code == COMP_STALL_ERROR || + xhci_requires_manual_halt_cleanup(xhci, ep_ctx, + trb_comp_code)) { + xhci_handle_halted_endpoint(xhci, ep, + ep_ring->stream_id, + NULL, + EP_HARD_RESET); + } + goto cleanup; + } + + /* We've skipped all the TDs on the ep ring when ep->skip set */ + if (ep->skip && td_num == 0) { + ep->skip = false; + xhci_dbg(xhci, "All tds on the ep_ring skipped. Clear skip flag for slot %u ep %u.\n", + slot_id, ep_index); + goto cleanup; + } + + td = list_first_entry(&ep_ring->td_list, struct xhci_td, + td_list); + if (ep->skip) + td_num--; + + /* Is this a TRB in the currently executing TD? */ + ep_seg = trb_in_td(xhci, ep_ring->deq_seg, ep_ring->dequeue, + td->last_trb, ep_trb_dma, false); + + /* + * Skip the Force Stopped Event. The event_trb(event_dma) of FSE + * is not in the current TD pointed by ep_ring->dequeue because + * that the hardware dequeue pointer still at the previous TRB + * of the current TD. The previous TRB maybe a Link TD or the + * last TRB of the previous TD. The command completion handle + * will take care the rest. + */ + if (!ep_seg && (trb_comp_code == COMP_STOPPED || + trb_comp_code == COMP_STOPPED_LENGTH_INVALID)) { + goto cleanup; + } + + if (!ep_seg) { + if (!ep->skip || + !usb_endpoint_xfer_isoc(&td->urb->ep->desc)) { + /* Some host controllers give a spurious + * successful event after a short transfer. + * Ignore it. + */ + if ((xhci->quirks & XHCI_SPURIOUS_SUCCESS) && + ep_ring->last_td_was_short) { + ep_ring->last_td_was_short = false; + goto cleanup; + } + /* HC is busted, give up! */ + xhci_err(xhci, + "ERROR Transfer event TRB DMA ptr not " + "part of current TD ep_index %d " + "comp_code %u\n", ep_index, + trb_comp_code); + trb_in_td(xhci, ep_ring->deq_seg, + ep_ring->dequeue, td->last_trb, + ep_trb_dma, true); + return -ESHUTDOWN; + } + + skip_isoc_td(xhci, td, ep, status); + goto cleanup; + } + if (trb_comp_code == COMP_SHORT_PACKET) + ep_ring->last_td_was_short = true; + else + ep_ring->last_td_was_short = false; + + if (ep->skip) { + xhci_dbg(xhci, + "Found td. Clear skip flag for slot %u ep %u.\n", + slot_id, ep_index); + ep->skip = false; + } + + ep_trb = &ep_seg->trbs[(ep_trb_dma - ep_seg->dma) / + sizeof(*ep_trb)]; + + trace_xhci_handle_transfer(ep_ring, + (struct xhci_generic_trb *) ep_trb); + + /* + * No-op TRB could trigger interrupts in a case where + * a URB was killed and a STALL_ERROR happens right + * after the endpoint ring stopped. Reset the halted + * endpoint. Otherwise, the endpoint remains stalled + * indefinitely. + */ + + if (trb_is_noop(ep_trb)) { + if (trb_comp_code == COMP_STALL_ERROR || + xhci_requires_manual_halt_cleanup(xhci, ep_ctx, + trb_comp_code)) + xhci_handle_halted_endpoint(xhci, ep, + ep_ring->stream_id, + td, EP_HARD_RESET); + goto cleanup; + } + + td->status = status; + + /* update the urb's actual_length and give back to the core */ + if (usb_endpoint_xfer_control(&td->urb->ep->desc)) + process_ctrl_td(xhci, ep, ep_ring, td, ep_trb, event); + else if (usb_endpoint_xfer_isoc(&td->urb->ep->desc)) + process_isoc_td(xhci, ep, ep_ring, td, ep_trb, event); + else + process_bulk_intr_td(xhci, ep, ep_ring, td, ep_trb, event); +cleanup: + handling_skipped_tds = ep->skip && + trb_comp_code != COMP_MISSED_SERVICE_ERROR && + trb_comp_code != COMP_NO_PING_RESPONSE_ERROR; + + /* + * Do not update event ring dequeue pointer if we're in a loop + * processing missed tds. + */ + if (!handling_skipped_tds) + inc_deq(xhci, xhci->event_ring); + + /* + * If ep->skip is set, it means there are missed tds on the + * endpoint ring need to take care of. + * Process them as short transfer until reach the td pointed by + * the event. + */ + } while (handling_skipped_tds); + + return 0; + +err_out: + xhci_err(xhci, "@%016llx %08x %08x %08x %08x\n", + (unsigned long long) xhci_trb_virt_to_dma( + xhci->event_ring->deq_seg, + xhci->event_ring->dequeue), + lower_32_bits(le64_to_cpu(event->buffer)), + upper_32_bits(le64_to_cpu(event->buffer)), + le32_to_cpu(event->transfer_len), + le32_to_cpu(event->flags)); + return -ENODEV; +} + +/* + * This function handles all OS-owned events on the event ring. It may drop + * xhci->lock between event processing (e.g. to pass up port status changes). + * Returns >0 for "possibly more events to process" (caller should call again), + * otherwise 0 if done. In future, <0 returns should indicate error code. + */ +static int xhci_handle_event(struct xhci_hcd *xhci) +{ + union xhci_trb *event; + int update_ptrs = 1; + u32 trb_type; + int ret; + + /* Event ring hasn't been allocated yet. */ + if (!xhci->event_ring || !xhci->event_ring->dequeue) { + xhci_err(xhci, "ERROR event ring not ready\n"); + return -ENOMEM; + } + + event = xhci->event_ring->dequeue; + /* Does the HC or OS own the TRB? */ + if ((le32_to_cpu(event->event_cmd.flags) & TRB_CYCLE) != + xhci->event_ring->cycle_state) + return 0; + + trace_xhci_handle_event(xhci->event_ring, &event->generic); + + /* + * Barrier between reading the TRB_CYCLE (valid) flag above and any + * speculative reads of the event's flags/data below. + */ + rmb(); + trb_type = TRB_FIELD_TO_TYPE(le32_to_cpu(event->event_cmd.flags)); + /* FIXME: Handle more event types. */ + + switch (trb_type) { + case TRB_COMPLETION: + handle_cmd_completion(xhci, &event->event_cmd); + break; + case TRB_PORT_STATUS: + handle_port_status(xhci, event); + update_ptrs = 0; + break; + case TRB_TRANSFER: + ret = handle_tx_event(xhci, &event->trans_event); + if (ret >= 0) + update_ptrs = 0; + break; + case TRB_DEV_NOTE: + handle_device_notification(xhci, event); + break; + default: + if (trb_type >= TRB_VENDOR_DEFINED_LOW) + handle_vendor_event(xhci, event, trb_type); + else + xhci_warn(xhci, "ERROR unknown event type %d\n", trb_type); + } + /* Any of the above functions may drop and re-acquire the lock, so check + * to make sure a watchdog timer didn't mark the host as non-responsive. + */ + if (xhci->xhc_state & XHCI_STATE_DYING) { + xhci_dbg(xhci, "xHCI host dying, returning from " + "event handler.\n"); + return 0; + } + + if (update_ptrs) + /* Update SW event ring dequeue pointer */ + inc_deq(xhci, xhci->event_ring); + + /* Are there more items on the event ring? Caller will call us again to + * check. + */ + return 1; +} + +/* + * Update Event Ring Dequeue Pointer: + * - When all events have finished + * - To avoid "Event Ring Full Error" condition + */ +static void xhci_update_erst_dequeue(struct xhci_hcd *xhci, + union xhci_trb *event_ring_deq) +{ + u64 temp_64; + dma_addr_t deq; + + temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); + /* If necessary, update the HW's version of the event ring deq ptr. */ + if (event_ring_deq != xhci->event_ring->dequeue) { + deq = xhci_trb_virt_to_dma(xhci->event_ring->deq_seg, + xhci->event_ring->dequeue); + if (deq == 0) + xhci_warn(xhci, "WARN something wrong with SW event ring dequeue ptr\n"); + /* + * Per 4.9.4, Software writes to the ERDP register shall + * always advance the Event Ring Dequeue Pointer value. + */ + if ((temp_64 & (u64) ~ERST_PTR_MASK) == + ((u64) deq & (u64) ~ERST_PTR_MASK)) + return; + + /* Update HC event ring dequeue pointer */ + temp_64 &= ERST_PTR_MASK; + temp_64 |= ((u64) deq & (u64) ~ERST_PTR_MASK); + } + + /* Clear the event handler busy flag (RW1C) */ + temp_64 |= ERST_EHB; + xhci_write_64(xhci, temp_64, &xhci->ir_set->erst_dequeue); +} + +/* + * xHCI spec says we can get an interrupt, and if the HC has an error condition, + * we might get bad data out of the event ring. Section 4.10.2.7 has a list of + * indicators of an event TRB error, but we check the status *first* to be safe. + */ +irqreturn_t xhci_irq(struct usb_hcd *hcd) +{ + struct xhci_hcd *xhci = hcd_to_xhci(hcd); + union xhci_trb *event_ring_deq; + irqreturn_t ret = IRQ_NONE; + u64 temp_64; + u32 status; + int event_loop = 0; + + spin_lock(&xhci->lock); + /* Check if the xHC generated the interrupt, or the irq is shared */ + status = readl(&xhci->op_regs->status); + if (status == ~(u32)0) { + xhci_hc_died(xhci); + ret = IRQ_HANDLED; + goto out; + } + + if (!(status & STS_EINT)) + goto out; + + if (status & STS_FATAL) { + xhci_warn(xhci, "WARNING: Host System Error\n"); + xhci_halt(xhci); + ret = IRQ_HANDLED; + goto out; + } + + /* + * Clear the op reg interrupt status first, + * so we can receive interrupts from other MSI-X interrupters. + * Write 1 to clear the interrupt status. + */ + status |= STS_EINT; + writel(status, &xhci->op_regs->status); + + if (!hcd->msi_enabled) { + u32 irq_pending; + irq_pending = readl(&xhci->ir_set->irq_pending); + irq_pending |= IMAN_IP; + writel(irq_pending, &xhci->ir_set->irq_pending); + } + + if (xhci->xhc_state & XHCI_STATE_DYING || + xhci->xhc_state & XHCI_STATE_HALTED) { + xhci_dbg(xhci, "xHCI dying, ignoring interrupt. " + "Shouldn't IRQs be disabled?\n"); + /* Clear the event handler busy flag (RW1C); + * the event ring should be empty. + */ + temp_64 = xhci_read_64(xhci, &xhci->ir_set->erst_dequeue); + xhci_write_64(xhci, temp_64 | ERST_EHB, + &xhci->ir_set->erst_dequeue); + ret = IRQ_HANDLED; + goto out; + } + + event_ring_deq = xhci->event_ring->dequeue; + /* FIXME this should be a delayed service routine + * that clears the EHB. + */ + while (xhci_handle_event(xhci) > 0) { + if (event_loop++ < TRBS_PER_SEGMENT / 2) + continue; + xhci_update_erst_dequeue(xhci, event_ring_deq); + event_ring_deq = xhci->event_ring->dequeue; + + /* ring is half-full, force isoc trbs to interrupt more often */ + if (xhci->isoc_bei_interval > AVOID_BEI_INTERVAL_MIN) + xhci->isoc_bei_interval = xhci->isoc_bei_interval / 2; + + event_loop = 0; + } + + xhci_update_erst_dequeue(xhci, event_ring_deq); + ret = IRQ_HANDLED; + +out: + spin_unlock(&xhci->lock); + + return ret; +} + +irqreturn_t xhci_msi_irq(int irq, void *hcd) +{ + return xhci_irq(hcd); +} + +/**** Endpoint Ring Operations ****/ + +/* + * Generic function for queueing a TRB on a ring. + * The caller must have checked to make sure there's room on the ring. + * + * @more_trbs_coming: Will you enqueue more TRBs before calling + * prepare_transfer()? + */ +static void queue_trb(struct xhci_hcd *xhci, struct xhci_ring *ring, + bool more_trbs_coming, + u32 field1, u32 field2, u32 field3, u32 field4) +{ + struct xhci_generic_trb *trb; + + trb = &ring->enqueue->generic; + trb->field[0] = cpu_to_le32(field1); + trb->field[1] = cpu_to_le32(field2); + trb->field[2] = cpu_to_le32(field3); + /* make sure TRB is fully written before giving it to the controller */ + wmb(); + trb->field[3] = cpu_to_le32(field4); + + trace_xhci_queue_trb(ring, trb); + + inc_enq(xhci, ring, more_trbs_coming); +} + +/* + * Does various checks on the endpoint ring, and makes it ready to queue num_trbs. + * FIXME allocate segments if the ring is full. + */ +static int prepare_ring(struct xhci_hcd *xhci, struct xhci_ring *ep_ring, + u32 ep_state, unsigned int num_trbs, gfp_t mem_flags) +{ + unsigned int num_trbs_needed; + unsigned int link_trb_count = 0; + + /* Make sure the endpoint has been added to xHC schedule */ + switch (ep_state) { + case EP_STATE_DISABLED: + /* + * USB core changed config/interfaces without notifying us, + * or hardware is reporting the wrong state. + */ + xhci_warn(xhci, "WARN urb submitted to disabled ep\n"); + return -ENOENT; + case EP_STATE_ERROR: + xhci_warn(xhci, "WARN waiting for error on ep to be cleared\n"); + /* FIXME event handling code for error needs to clear it */ + /* XXX not sure if this should be -ENOENT or not */ + return -EINVAL; + case EP_STATE_HALTED: + xhci_dbg(xhci, "WARN halted endpoint, queueing URB anyway.\n"); + break; + case EP_STATE_STOPPED: + case EP_STATE_RUNNING: + break; + default: + xhci_err(xhci, "ERROR unknown endpoint state for ep\n"); + /* + * FIXME issue Configure Endpoint command to try to get the HC + * back into a known state. + */ + return -EINVAL; + } + + while (1) { + if (room_on_ring(xhci, ep_ring, num_trbs)) + break; + + if (ep_ring == xhci->cmd_ring) { + xhci_err(xhci, "Do not support expand command ring\n"); + return -ENOMEM; + } + + xhci_dbg_trace(xhci, trace_xhci_dbg_ring_expansion, + "ERROR no room on ep ring, try ring expansion"); + num_trbs_needed = num_trbs - ep_ring->num_trbs_free; + if (xhci_ring_expansion(xhci, ep_ring, num_trbs_needed, + mem_flags)) { + xhci_err(xhci, "Ring expansion failed\n"); + return -ENOMEM; + } + } + + while (trb_is_link(ep_ring->enqueue)) { + /* If we're not dealing with 0.95 hardware or isoc rings + * on AMD 0.96 host, clear the chain bit. + */ + if (!xhci_link_trb_quirk(xhci) && + !(ep_ring->type == TYPE_ISOC && + (xhci->quirks & XHCI_AMD_0x96_HOST))) + ep_ring->enqueue->link.control &= + cpu_to_le32(~TRB_CHAIN); + else + ep_ring->enqueue->link.control |= + cpu_to_le32(TRB_CHAIN); + + wmb(); + ep_ring->enqueue->link.control ^= cpu_to_le32(TRB_CYCLE); + + /* Toggle the cycle bit after the last ring segment. */ + if (link_trb_toggles_cycle(ep_ring->enqueue)) + ep_ring->cycle_state ^= 1; + + ep_ring->enq_seg = ep_ring->enq_seg->next; + ep_ring->enqueue = ep_ring->enq_seg->trbs; + + /* prevent infinite loop if all first trbs are link trbs */ + if (link_trb_count++ > ep_ring->num_segs) { + xhci_warn(xhci, "Ring is an endless link TRB loop\n"); + return -EINVAL; + } + } + + if (last_trb_on_seg(ep_ring->enq_seg, ep_ring->enqueue)) { + xhci_warn(xhci, "Missing link TRB at end of ring segment\n"); + return -EINVAL; + } + + return 0; +} + +static int prepare_transfer(struct xhci_hcd *xhci, + struct xhci_virt_device *xdev, + unsigned int ep_index, + unsigned int stream_id, + unsigned int num_trbs, + struct urb *urb, + unsigned int td_index, + gfp_t mem_flags) +{ + int ret; + struct urb_priv *urb_priv; + struct xhci_td *td; + struct xhci_ring *ep_ring; + struct xhci_ep_ctx *ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index); + + ep_ring = xhci_triad_to_transfer_ring(xhci, xdev->slot_id, ep_index, + stream_id); + if (!ep_ring) { + xhci_dbg(xhci, "Can't prepare ring for bad stream ID %u\n", + stream_id); + return -EINVAL; + } + + ret = prepare_ring(xhci, ep_ring, GET_EP_CTX_STATE(ep_ctx), + num_trbs, mem_flags); + if (ret) + return ret; + + urb_priv = urb->hcpriv; + td = &urb_priv->td[td_index]; + + INIT_LIST_HEAD(&td->td_list); + INIT_LIST_HEAD(&td->cancelled_td_list); + + if (td_index == 0) { + ret = usb_hcd_link_urb_to_ep(bus_to_hcd(urb->dev->bus), urb); + if (unlikely(ret)) + return ret; + } + + td->urb = urb; + /* Add this TD to the tail of the endpoint ring's TD list */ + list_add_tail(&td->td_list, &ep_ring->td_list); + td->start_seg = ep_ring->enq_seg; + td->first_trb = ep_ring->enqueue; + + return 0; +} + +unsigned int count_trbs(u64 addr, u64 len) +{ + unsigned int num_trbs; + + num_trbs = DIV_ROUND_UP(len + (addr & (TRB_MAX_BUFF_SIZE - 1)), + TRB_MAX_BUFF_SIZE); + if (num_trbs == 0) + num_trbs++; + + return num_trbs; +} + +static inline unsigned int count_trbs_needed(struct urb *urb) +{ + return count_trbs(urb->transfer_dma, urb->transfer_buffer_length); +} + +static unsigned int count_sg_trbs_needed(struct urb *urb) +{ + struct scatterlist *sg; + unsigned int i, len, full_len, num_trbs = 0; + + full_len = urb->transfer_buffer_length; + + for_each_sg(urb->sg, sg, urb->num_mapped_sgs, i) { + len = sg_dma_len(sg); + num_trbs += count_trbs(sg_dma_address(sg), len); + len = min_t(unsigned int, len, full_len); + full_len -= len; + if (full_len == 0) + break; + } + + return num_trbs; +} + +static unsigned int count_isoc_trbs_needed(struct urb *urb, int i) +{ + u64 addr, len; + + addr = (u64) (urb->transfer_dma + urb->iso_frame_desc[i].offset); + len = urb->iso_frame_desc[i].length; + + return count_trbs(addr, len); +} + +static void check_trb_math(struct urb *urb, int running_total) +{ + if (unlikely(running_total != urb->transfer_buffer_length)) + dev_err(&urb->dev->dev, "%s - ep %#x - Miscalculated tx length, " + "queued %#x (%d), asked for %#x (%d)\n", + __func__, + urb->ep->desc.bEndpointAddress, + running_total, running_total, + urb->transfer_buffer_length, + urb->transfer_buffer_length); +} + +static void giveback_first_trb(struct xhci_hcd *xhci, int slot_id, + unsigned int ep_index, unsigned int stream_id, int start_cycle, + struct xhci_generic_trb *start_trb) +{ + /* + * Pass all the TRBs to the hardware at once and make sure this write + * isn't reordered. + */ + wmb(); + if (start_cycle) + start_trb->field[3] |= cpu_to_le32(start_cycle); + else + start_trb->field[3] &= cpu_to_le32(~TRB_CYCLE); + xhci_ring_ep_doorbell(xhci, slot_id, ep_index, stream_id); +} + +static void check_interval(struct xhci_hcd *xhci, struct urb *urb, + struct xhci_ep_ctx *ep_ctx) +{ + int xhci_interval; + int ep_interval; + + xhci_interval = EP_INTERVAL_TO_UFRAMES(le32_to_cpu(ep_ctx->ep_info)); + ep_interval = urb->interval; + + /* Convert to microframes */ + if (urb->dev->speed == USB_SPEED_LOW || + urb->dev->speed == USB_SPEED_FULL) + ep_interval *= 8; + + /* FIXME change this to a warning and a suggestion to use the new API + * to set the polling interval (once the API is added). + */ + if (xhci_interval != ep_interval) { + dev_dbg_ratelimited(&urb->dev->dev, + "Driver uses different interval (%d microframe%s) than xHCI (%d microframe%s)\n", + ep_interval, ep_interval == 1 ? "" : "s", + xhci_interval, xhci_interval == 1 ? "" : "s"); + urb->interval = xhci_interval; + /* Convert back to frames for LS/FS devices */ + if (urb->dev->speed == USB_SPEED_LOW || + urb->dev->speed == USB_SPEED_FULL) + urb->interval /= 8; + } +} + +/* + * xHCI uses normal TRBs for both bulk and interrupt. When the interrupt + * endpoint is to be serviced, the xHC will consume (at most) one TD. A TD + * (comprised of sg list entries) can take several service intervals to + * transmit. + */ +int xhci_queue_intr_tx(struct xhci_hcd *xhci, gfp_t mem_flags, + struct urb *urb, int slot_id, unsigned int ep_index) +{ + struct xhci_ep_ctx *ep_ctx; + + ep_ctx = xhci_get_ep_ctx(xhci, xhci->devs[slot_id]->out_ctx, ep_index); + check_interval(xhci, urb, ep_ctx); + + return xhci_queue_bulk_tx(xhci, mem_flags, urb, slot_id, ep_index); +} + +/* + * For xHCI 1.0 host controllers, TD size is the number of max packet sized + * packets remaining in the TD (*not* including this TRB). + * + * Total TD packet count = total_packet_count = + * DIV_ROUND_UP(TD size in bytes / wMaxPacketSize) + * + * Packets transferred up to and including this TRB = packets_transferred = + * rounddown(total bytes transferred including this TRB / wMaxPacketSize) + * + * TD size = total_packet_count - packets_transferred + * + * For xHCI 0.96 and older, TD size field should be the remaining bytes + * including this TRB, right shifted by 10 + * + * For all hosts it must fit in bits 21:17, so it can't be bigger than 31. + * This is taken care of in the TRB_TD_SIZE() macro + * + * The last TRB in a TD must have the TD size set to zero. + */ +static u32 xhci_td_remainder(struct xhci_hcd *xhci, int transferred, + int trb_buff_len, unsigned int td_total_len, + struct urb *urb, bool more_trbs_coming) +{ + u32 maxp, total_packet_count; + + /* MTK xHCI 0.96 contains some features from 1.0 */ + if (xhci->hci_version < 0x100 && !(xhci->quirks & XHCI_MTK_HOST)) + return ((td_total_len - transferred) >> 10); + + /* One TRB with a zero-length data packet. */ + if (!more_trbs_coming || (transferred == 0 && trb_buff_len == 0) || + trb_buff_len == td_total_len) + return 0; + + /* for MTK xHCI 0.96, TD size include this TRB, but not in 1.x */ + if ((xhci->quirks & XHCI_MTK_HOST) && (xhci->hci_version < 0x100)) + trb_buff_len = 0; + + maxp = usb_endpoint_maxp(&urb->ep->desc); + total_packet_count = DIV_ROUND_UP(td_total_len, maxp); + + /* Queueing functions don't count the current TRB into transferred */ + return (total_packet_count - ((transferred + trb_buff_len) / maxp)); +} + + +static int xhci_align_td(struct xhci_hcd *xhci, struct urb *urb, u32 enqd_len, + u32 *trb_buff_len, struct xhci_segment *seg) +{ + struct device *dev = xhci_to_hcd(xhci)->self.sysdev; + unsigned int unalign; + unsigned int max_pkt; + u32 new_buff_len; + size_t len; + + max_pkt = usb_endpoint_maxp(&urb->ep->desc); + unalign = (enqd_len + *trb_buff_len) % max_pkt; + + /* we got lucky, last normal TRB data on segment is packet aligned */ + if (unalign == 0) + return 0; + + xhci_dbg(xhci, "Unaligned %d bytes, buff len %d\n", + unalign, *trb_buff_len); + + /* is the last nornal TRB alignable by splitting it */ + if (*trb_buff_len > unalign) { + *trb_buff_len -= unalign; + xhci_dbg(xhci, "split align, new buff len %d\n", *trb_buff_len); + return 0; + } + + /* + * We want enqd_len + trb_buff_len to sum up to a number aligned to + * number which is divisible by the endpoint's wMaxPacketSize. IOW: + * (size of currently enqueued TRBs + remainder) % wMaxPacketSize == 0. + */ + new_buff_len = max_pkt - (enqd_len % max_pkt); + + if (new_buff_len > (urb->transfer_buffer_length - enqd_len)) + new_buff_len = (urb->transfer_buffer_length - enqd_len); + + /* create a max max_pkt sized bounce buffer pointed to by last trb */ + if (usb_urb_dir_out(urb)) { + if (urb->num_sgs) { + len = sg_pcopy_to_buffer(urb->sg, urb->num_sgs, + seg->bounce_buf, new_buff_len, enqd_len); + if (len != new_buff_len) + xhci_warn(xhci, "WARN Wrong bounce buffer write length: %zu != %d\n", + len, new_buff_len); + } else { + memcpy(seg->bounce_buf, urb->transfer_buffer + enqd_len, new_buff_len); + } + + seg->bounce_dma = dma_map_single(dev, seg->bounce_buf, + max_pkt, DMA_TO_DEVICE); + } else { + seg->bounce_dma = dma_map_single(dev, seg->bounce_buf, + max_pkt, DMA_FROM_DEVICE); + } + + if (dma_mapping_error(dev, seg->bounce_dma)) { + /* try without aligning. Some host controllers survive */ + xhci_warn(xhci, "Failed mapping bounce buffer, not aligning\n"); + return 0; + } + *trb_buff_len = new_buff_len; + seg->bounce_len = new_buff_len; + seg->bounce_offs = enqd_len; + + xhci_dbg(xhci, "Bounce align, new buff len %d\n", *trb_buff_len); + + return 1; +} + +/* This is very similar to what ehci-q.c qtd_fill() does */ +int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, + struct urb *urb, int slot_id, unsigned int ep_index) +{ + struct xhci_ring *ring; + struct urb_priv *urb_priv; + struct xhci_td *td; + struct xhci_generic_trb *start_trb; + struct scatterlist *sg = NULL; + bool more_trbs_coming = true; + bool need_zero_pkt = false; + bool first_trb = true; + unsigned int num_trbs; + unsigned int start_cycle, num_sgs = 0; + unsigned int enqd_len, block_len, trb_buff_len, full_len; + int sent_len, ret; + u32 field, length_field, remainder; + u64 addr, send_addr; + + ring = xhci_urb_to_transfer_ring(xhci, urb); + if (!ring) + return -EINVAL; + + full_len = urb->transfer_buffer_length; + /* If we have scatter/gather list, we use it. */ + if (urb->num_sgs && !(urb->transfer_flags & URB_DMA_MAP_SINGLE)) { + num_sgs = urb->num_mapped_sgs; + sg = urb->sg; + addr = (u64) sg_dma_address(sg); + block_len = sg_dma_len(sg); + num_trbs = count_sg_trbs_needed(urb); + } else { + num_trbs = count_trbs_needed(urb); + addr = (u64) urb->transfer_dma; + block_len = full_len; + } + ret = prepare_transfer(xhci, xhci->devs[slot_id], + ep_index, urb->stream_id, + num_trbs, urb, 0, mem_flags); + if (unlikely(ret < 0)) + return ret; + + urb_priv = urb->hcpriv; + + /* Deal with URB_ZERO_PACKET - need one more td/trb */ + if (urb->transfer_flags & URB_ZERO_PACKET && urb_priv->num_tds > 1) + need_zero_pkt = true; + + td = &urb_priv->td[0]; + + /* + * Don't give the first TRB to the hardware (by toggling the cycle bit) + * until we've finished creating all the other TRBs. The ring's cycle + * state may change as we enqueue the other TRBs, so save it too. + */ + start_trb = &ring->enqueue->generic; + start_cycle = ring->cycle_state; + send_addr = addr; + + /* Queue the TRBs, even if they are zero-length */ + for (enqd_len = 0; first_trb || enqd_len < full_len; + enqd_len += trb_buff_len) { + field = TRB_TYPE(TRB_NORMAL); + + /* TRB buffer should not cross 64KB boundaries */ + trb_buff_len = TRB_BUFF_LEN_UP_TO_BOUNDARY(addr); + trb_buff_len = min_t(unsigned int, trb_buff_len, block_len); + + if (enqd_len + trb_buff_len > full_len) + trb_buff_len = full_len - enqd_len; + + /* Don't change the cycle bit of the first TRB until later */ + if (first_trb) { + first_trb = false; + if (start_cycle == 0) + field |= TRB_CYCLE; + } else + field |= ring->cycle_state; + + /* Chain all the TRBs together; clear the chain bit in the last + * TRB to indicate it's the last TRB in the chain. + */ + if (enqd_len + trb_buff_len < full_len) { + field |= TRB_CHAIN; + if (trb_is_link(ring->enqueue + 1)) { + if (xhci_align_td(xhci, urb, enqd_len, + &trb_buff_len, + ring->enq_seg)) { + send_addr = ring->enq_seg->bounce_dma; + /* assuming TD won't span 2 segs */ + td->bounce_seg = ring->enq_seg; + } + } + } + if (enqd_len + trb_buff_len >= full_len) { + field &= ~TRB_CHAIN; + field |= TRB_IOC; + more_trbs_coming = false; + td->last_trb = ring->enqueue; + td->last_trb_seg = ring->enq_seg; + if (xhci_urb_suitable_for_idt(urb)) { + memcpy(&send_addr, urb->transfer_buffer, + trb_buff_len); + le64_to_cpus(&send_addr); + field |= TRB_IDT; + } + } + + /* Only set interrupt on short packet for IN endpoints */ + if (usb_urb_dir_in(urb)) + field |= TRB_ISP; + + /* Set the TRB length, TD size, and interrupter fields. */ + remainder = xhci_td_remainder(xhci, enqd_len, trb_buff_len, + full_len, urb, more_trbs_coming); + + length_field = TRB_LEN(trb_buff_len) | + TRB_TD_SIZE(remainder) | + TRB_INTR_TARGET(0); + + queue_trb(xhci, ring, more_trbs_coming | need_zero_pkt, + lower_32_bits(send_addr), + upper_32_bits(send_addr), + length_field, + field); + td->num_trbs++; + addr += trb_buff_len; + sent_len = trb_buff_len; + + while (sg && sent_len >= block_len) { + /* New sg entry */ + --num_sgs; + sent_len -= block_len; + sg = sg_next(sg); + if (num_sgs != 0 && sg) { + block_len = sg_dma_len(sg); + addr = (u64) sg_dma_address(sg); + addr += sent_len; + } + } + block_len -= sent_len; + send_addr = addr; + } + + if (need_zero_pkt) { + ret = prepare_transfer(xhci, xhci->devs[slot_id], + ep_index, urb->stream_id, + 1, urb, 1, mem_flags); + urb_priv->td[1].last_trb = ring->enqueue; + urb_priv->td[1].last_trb_seg = ring->enq_seg; + field = TRB_TYPE(TRB_NORMAL) | ring->cycle_state | TRB_IOC; + queue_trb(xhci, ring, 0, 0, 0, TRB_INTR_TARGET(0), field); + urb_priv->td[1].num_trbs++; + } + + check_trb_math(urb, enqd_len); + giveback_first_trb(xhci, slot_id, ep_index, urb->stream_id, + start_cycle, start_trb); + return 0; +} + +/* Caller must have locked xhci->lock */ +int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags, + struct urb *urb, int slot_id, unsigned int ep_index) +{ + struct xhci_ring *ep_ring; + int num_trbs; + int ret; + struct usb_ctrlrequest *setup; + struct xhci_generic_trb *start_trb; + int start_cycle; + u32 field; + struct urb_priv *urb_priv; + struct xhci_td *td; + + ep_ring = xhci_urb_to_transfer_ring(xhci, urb); + if (!ep_ring) + return -EINVAL; + + /* + * Need to copy setup packet into setup TRB, so we can't use the setup + * DMA address. + */ + if (!urb->setup_packet) + return -EINVAL; + + /* 1 TRB for setup, 1 for status */ + num_trbs = 2; + /* + * Don't need to check if we need additional event data and normal TRBs, + * since data in control transfers will never get bigger than 16MB + * XXX: can we get a buffer that crosses 64KB boundaries? + */ + if (urb->transfer_buffer_length > 0) + num_trbs++; + ret = prepare_transfer(xhci, xhci->devs[slot_id], + ep_index, urb->stream_id, + num_trbs, urb, 0, mem_flags); + if (ret < 0) + return ret; + + urb_priv = urb->hcpriv; + td = &urb_priv->td[0]; + td->num_trbs = num_trbs; + + /* + * Don't give the first TRB to the hardware (by toggling the cycle bit) + * until we've finished creating all the other TRBs. The ring's cycle + * state may change as we enqueue the other TRBs, so save it too. + */ + start_trb = &ep_ring->enqueue->generic; + start_cycle = ep_ring->cycle_state; + + /* Queue setup TRB - see section 6.4.1.2.1 */ + /* FIXME better way to translate setup_packet into two u32 fields? */ + setup = (struct usb_ctrlrequest *) urb->setup_packet; + field = 0; + field |= TRB_IDT | TRB_TYPE(TRB_SETUP); + if (start_cycle == 0) + field |= 0x1; + + /* xHCI 1.0/1.1 6.4.1.2.1: Transfer Type field */ + if ((xhci->hci_version >= 0x100) || (xhci->quirks & XHCI_MTK_HOST)) { + if (urb->transfer_buffer_length > 0) { + if (setup->bRequestType & USB_DIR_IN) + field |= TRB_TX_TYPE(TRB_DATA_IN); + else + field |= TRB_TX_TYPE(TRB_DATA_OUT); + } + } + + queue_trb(xhci, ep_ring, true, + setup->bRequestType | setup->bRequest << 8 | le16_to_cpu(setup->wValue) << 16, + le16_to_cpu(setup->wIndex) | le16_to_cpu(setup->wLength) << 16, + TRB_LEN(8) | TRB_INTR_TARGET(0), + /* Immediate data in pointer */ + field); + + /* If there's data, queue data TRBs */ + /* Only set interrupt on short packet for IN endpoints */ + if (usb_urb_dir_in(urb)) + field = TRB_ISP | TRB_TYPE(TRB_DATA); + else + field = TRB_TYPE(TRB_DATA); + + if (urb->transfer_buffer_length > 0) { + u32 length_field, remainder; + u64 addr; + + if (xhci_urb_suitable_for_idt(urb)) { + memcpy(&addr, urb->transfer_buffer, + urb->transfer_buffer_length); + le64_to_cpus(&addr); + field |= TRB_IDT; + } else { + addr = (u64) urb->transfer_dma; + } + + remainder = xhci_td_remainder(xhci, 0, + urb->transfer_buffer_length, + urb->transfer_buffer_length, + urb, 1); + length_field = TRB_LEN(urb->transfer_buffer_length) | + TRB_TD_SIZE(remainder) | + TRB_INTR_TARGET(0); + if (setup->bRequestType & USB_DIR_IN) + field |= TRB_DIR_IN; + queue_trb(xhci, ep_ring, true, + lower_32_bits(addr), + upper_32_bits(addr), + length_field, + field | ep_ring->cycle_state); + } + + /* Save the DMA address of the last TRB in the TD */ + td->last_trb = ep_ring->enqueue; + td->last_trb_seg = ep_ring->enq_seg; + + /* Queue status TRB - see Table 7 and sections 4.11.2.2 and 6.4.1.2.3 */ + /* If the device sent data, the status stage is an OUT transfer */ + if (urb->transfer_buffer_length > 0 && setup->bRequestType & USB_DIR_IN) + field = 0; + else + field = TRB_DIR_IN; + queue_trb(xhci, ep_ring, false, + 0, + 0, + TRB_INTR_TARGET(0), + /* Event on completion */ + field | TRB_IOC | TRB_TYPE(TRB_STATUS) | ep_ring->cycle_state); + + giveback_first_trb(xhci, slot_id, ep_index, 0, + start_cycle, start_trb); + return 0; +} + +/* + * The transfer burst count field of the isochronous TRB defines the number of + * bursts that are required to move all packets in this TD. Only SuperSpeed + * devices can burst up to bMaxBurst number of packets per service interval. + * This field is zero based, meaning a value of zero in the field means one + * burst. Basically, for everything but SuperSpeed devices, this field will be + * zero. Only xHCI 1.0 host controllers support this field. + */ +static unsigned int xhci_get_burst_count(struct xhci_hcd *xhci, + struct urb *urb, unsigned int total_packet_count) +{ + unsigned int max_burst; + + if (xhci->hci_version < 0x100 || urb->dev->speed < USB_SPEED_SUPER) + return 0; + + max_burst = urb->ep->ss_ep_comp.bMaxBurst; + return DIV_ROUND_UP(total_packet_count, max_burst + 1) - 1; +} + +/* + * Returns the number of packets in the last "burst" of packets. This field is + * valid for all speeds of devices. USB 2.0 devices can only do one "burst", so + * the last burst packet count is equal to the total number of packets in the + * TD. SuperSpeed endpoints can have up to 3 bursts. All but the last burst + * must contain (bMaxBurst + 1) number of packets, but the last burst can + * contain 1 to (bMaxBurst + 1) packets. + */ +static unsigned int xhci_get_last_burst_packet_count(struct xhci_hcd *xhci, + struct urb *urb, unsigned int total_packet_count) +{ + unsigned int max_burst; + unsigned int residue; + + if (xhci->hci_version < 0x100) + return 0; + + if (urb->dev->speed >= USB_SPEED_SUPER) { + /* bMaxBurst is zero based: 0 means 1 packet per burst */ + max_burst = urb->ep->ss_ep_comp.bMaxBurst; + residue = total_packet_count % (max_burst + 1); + /* If residue is zero, the last burst contains (max_burst + 1) + * number of packets, but the TLBPC field is zero-based. + */ + if (residue == 0) + return max_burst; + return residue - 1; + } + if (total_packet_count == 0) + return 0; + return total_packet_count - 1; +} + +/* + * Calculates Frame ID field of the isochronous TRB identifies the + * target frame that the Interval associated with this Isochronous + * Transfer Descriptor will start on. Refer to 4.11.2.5 in 1.1 spec. + * + * Returns actual frame id on success, negative value on error. + */ +static int xhci_get_isoc_frame_id(struct xhci_hcd *xhci, + struct urb *urb, int index) +{ + int start_frame, ist, ret = 0; + int start_frame_id, end_frame_id, current_frame_id; + + if (urb->dev->speed == USB_SPEED_LOW || + urb->dev->speed == USB_SPEED_FULL) + start_frame = urb->start_frame + index * urb->interval; + else + start_frame = (urb->start_frame + index * urb->interval) >> 3; + + /* Isochronous Scheduling Threshold (IST, bits 0~3 in HCSPARAMS2): + * + * If bit [3] of IST is cleared to '0', software can add a TRB no + * later than IST[2:0] Microframes before that TRB is scheduled to + * be executed. + * If bit [3] of IST is set to '1', software can add a TRB no later + * than IST[2:0] Frames before that TRB is scheduled to be executed. + */ + ist = HCS_IST(xhci->hcs_params2) & 0x7; + if (HCS_IST(xhci->hcs_params2) & (1 << 3)) + ist <<= 3; + + /* Software shall not schedule an Isoch TD with a Frame ID value that + * is less than the Start Frame ID or greater than the End Frame ID, + * where: + * + * End Frame ID = (Current MFINDEX register value + 895 ms.) MOD 2048 + * Start Frame ID = (Current MFINDEX register value + IST + 1) MOD 2048 + * + * Both the End Frame ID and Start Frame ID values are calculated + * in microframes. When software determines the valid Frame ID value; + * The End Frame ID value should be rounded down to the nearest Frame + * boundary, and the Start Frame ID value should be rounded up to the + * nearest Frame boundary. + */ + current_frame_id = readl(&xhci->run_regs->microframe_index); + start_frame_id = roundup(current_frame_id + ist + 1, 8); + end_frame_id = rounddown(current_frame_id + 895 * 8, 8); + + start_frame &= 0x7ff; + start_frame_id = (start_frame_id >> 3) & 0x7ff; + end_frame_id = (end_frame_id >> 3) & 0x7ff; + + xhci_dbg(xhci, "%s: index %d, reg 0x%x start_frame_id 0x%x, end_frame_id 0x%x, start_frame 0x%x\n", + __func__, index, readl(&xhci->run_regs->microframe_index), + start_frame_id, end_frame_id, start_frame); + + if (start_frame_id < end_frame_id) { + if (start_frame > end_frame_id || + start_frame < start_frame_id) + ret = -EINVAL; + } else if (start_frame_id > end_frame_id) { + if ((start_frame > end_frame_id && + start_frame < start_frame_id)) + ret = -EINVAL; + } else { + ret = -EINVAL; + } + + if (index == 0) { + if (ret == -EINVAL || start_frame == start_frame_id) { + start_frame = start_frame_id + 1; + if (urb->dev->speed == USB_SPEED_LOW || + urb->dev->speed == USB_SPEED_FULL) + urb->start_frame = start_frame; + else + urb->start_frame = start_frame << 3; + ret = 0; + } + } + + if (ret) { + xhci_warn(xhci, "Frame ID %d (reg %d, index %d) beyond range (%d, %d)\n", + start_frame, current_frame_id, index, + start_frame_id, end_frame_id); + xhci_warn(xhci, "Ignore frame ID field, use SIA bit instead\n"); + return ret; + } + + return start_frame; +} + +/* Check if we should generate event interrupt for a TD in an isoc URB */ +static bool trb_block_event_intr(struct xhci_hcd *xhci, int num_tds, int i) +{ + if (xhci->hci_version < 0x100) + return false; + /* always generate an event interrupt for the last TD */ + if (i == num_tds - 1) + return false; + /* + * If AVOID_BEI is set the host handles full event rings poorly, + * generate an event at least every 8th TD to clear the event ring + */ + if (i && xhci->quirks & XHCI_AVOID_BEI) + return !!(i % xhci->isoc_bei_interval); + + return true; +} + +/* This is for isoc transfer */ +static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags, + struct urb *urb, int slot_id, unsigned int ep_index) +{ + struct xhci_ring *ep_ring; + struct urb_priv *urb_priv; + struct xhci_td *td; + int num_tds, trbs_per_td; + struct xhci_generic_trb *start_trb; + bool first_trb; + int start_cycle; + u32 field, length_field; + int running_total, trb_buff_len, td_len, td_remain_len, ret; + u64 start_addr, addr; + int i, j; + bool more_trbs_coming; + struct xhci_virt_ep *xep; + int frame_id; + + xep = &xhci->devs[slot_id]->eps[ep_index]; + ep_ring = xhci->devs[slot_id]->eps[ep_index].ring; + + num_tds = urb->number_of_packets; + if (num_tds < 1) { + xhci_dbg(xhci, "Isoc URB with zero packets?\n"); + return -EINVAL; + } + start_addr = (u64) urb->transfer_dma; + start_trb = &ep_ring->enqueue->generic; + start_cycle = ep_ring->cycle_state; + + urb_priv = urb->hcpriv; + /* Queue the TRBs for each TD, even if they are zero-length */ + for (i = 0; i < num_tds; i++) { + unsigned int total_pkt_count, max_pkt; + unsigned int burst_count, last_burst_pkt_count; + u32 sia_frame_id; + + first_trb = true; + running_total = 0; + addr = start_addr + urb->iso_frame_desc[i].offset; + td_len = urb->iso_frame_desc[i].length; + td_remain_len = td_len; + max_pkt = usb_endpoint_maxp(&urb->ep->desc); + total_pkt_count = DIV_ROUND_UP(td_len, max_pkt); + + /* A zero-length transfer still involves at least one packet. */ + if (total_pkt_count == 0) + total_pkt_count++; + burst_count = xhci_get_burst_count(xhci, urb, total_pkt_count); + last_burst_pkt_count = xhci_get_last_burst_packet_count(xhci, + urb, total_pkt_count); + + trbs_per_td = count_isoc_trbs_needed(urb, i); + + ret = prepare_transfer(xhci, xhci->devs[slot_id], ep_index, + urb->stream_id, trbs_per_td, urb, i, mem_flags); + if (ret < 0) { + if (i == 0) + return ret; + goto cleanup; + } + td = &urb_priv->td[i]; + td->num_trbs = trbs_per_td; + /* use SIA as default, if frame id is used overwrite it */ + sia_frame_id = TRB_SIA; + if (!(urb->transfer_flags & URB_ISO_ASAP) && + HCC_CFC(xhci->hcc_params)) { + frame_id = xhci_get_isoc_frame_id(xhci, urb, i); + if (frame_id >= 0) + sia_frame_id = TRB_FRAME_ID(frame_id); + } + /* + * Set isoc specific data for the first TRB in a TD. + * Prevent HW from getting the TRBs by keeping the cycle state + * inverted in the first TDs isoc TRB. + */ + field = TRB_TYPE(TRB_ISOC) | + TRB_TLBPC(last_burst_pkt_count) | + sia_frame_id | + (i ? ep_ring->cycle_state : !start_cycle); + + /* xhci 1.1 with ETE uses TD_Size field for TBC, old is Rsvdz */ + if (!xep->use_extended_tbc) + field |= TRB_TBC(burst_count); + + /* fill the rest of the TRB fields, and remaining normal TRBs */ + for (j = 0; j < trbs_per_td; j++) { + u32 remainder = 0; + + /* only first TRB is isoc, overwrite otherwise */ + if (!first_trb) + field = TRB_TYPE(TRB_NORMAL) | + ep_ring->cycle_state; + + /* Only set interrupt on short packet for IN EPs */ + if (usb_urb_dir_in(urb)) + field |= TRB_ISP; + + /* Set the chain bit for all except the last TRB */ + if (j < trbs_per_td - 1) { + more_trbs_coming = true; + field |= TRB_CHAIN; + } else { + more_trbs_coming = false; + td->last_trb = ep_ring->enqueue; + td->last_trb_seg = ep_ring->enq_seg; + field |= TRB_IOC; + if (trb_block_event_intr(xhci, num_tds, i)) + field |= TRB_BEI; + } + /* Calculate TRB length */ + trb_buff_len = TRB_BUFF_LEN_UP_TO_BOUNDARY(addr); + if (trb_buff_len > td_remain_len) + trb_buff_len = td_remain_len; + + /* Set the TRB length, TD size, & interrupter fields. */ + remainder = xhci_td_remainder(xhci, running_total, + trb_buff_len, td_len, + urb, more_trbs_coming); + + length_field = TRB_LEN(trb_buff_len) | + TRB_INTR_TARGET(0); + + /* xhci 1.1 with ETE uses TD Size field for TBC */ + if (first_trb && xep->use_extended_tbc) + length_field |= TRB_TD_SIZE_TBC(burst_count); + else + length_field |= TRB_TD_SIZE(remainder); + first_trb = false; + + queue_trb(xhci, ep_ring, more_trbs_coming, + lower_32_bits(addr), + upper_32_bits(addr), + length_field, + field); + running_total += trb_buff_len; + + addr += trb_buff_len; + td_remain_len -= trb_buff_len; + } + + /* Check TD length */ + if (running_total != td_len) { + xhci_err(xhci, "ISOC TD length unmatch\n"); + ret = -EINVAL; + goto cleanup; + } + } + + /* store the next frame id */ + if (HCC_CFC(xhci->hcc_params)) + xep->next_frame_id = urb->start_frame + num_tds * urb->interval; + + if (xhci_to_hcd(xhci)->self.bandwidth_isoc_reqs == 0) { + if (xhci->quirks & XHCI_AMD_PLL_FIX) + usb_amd_quirk_pll_disable(); + } + xhci_to_hcd(xhci)->self.bandwidth_isoc_reqs++; + + giveback_first_trb(xhci, slot_id, ep_index, urb->stream_id, + start_cycle, start_trb); + return 0; +cleanup: + /* Clean up a partially enqueued isoc transfer. */ + + for (i--; i >= 0; i--) + list_del_init(&urb_priv->td[i].td_list); + + /* Use the first TD as a temporary variable to turn the TDs we've queued + * into No-ops with a software-owned cycle bit. That way the hardware + * won't accidentally start executing bogus TDs when we partially + * overwrite them. td->first_trb and td->start_seg are already set. + */ + urb_priv->td[0].last_trb = ep_ring->enqueue; + /* Every TRB except the first & last will have its cycle bit flipped. */ + td_to_noop(xhci, ep_ring, &urb_priv->td[0], true); + + /* Reset the ring enqueue back to the first TRB and its cycle bit. */ + ep_ring->enqueue = urb_priv->td[0].first_trb; + ep_ring->enq_seg = urb_priv->td[0].start_seg; + ep_ring->cycle_state = start_cycle; + ep_ring->num_trbs_free = ep_ring->num_trbs_free_temp; + usb_hcd_unlink_urb_from_ep(bus_to_hcd(urb->dev->bus), urb); + return ret; +} + +/* + * Check transfer ring to guarantee there is enough room for the urb. + * Update ISO URB start_frame and interval. + * Update interval as xhci_queue_intr_tx does. Use xhci frame_index to + * update urb->start_frame if URB_ISO_ASAP is set in transfer_flags or + * Contiguous Frame ID is not supported by HC. + */ +int xhci_queue_isoc_tx_prepare(struct xhci_hcd *xhci, gfp_t mem_flags, + struct urb *urb, int slot_id, unsigned int ep_index) +{ + struct xhci_virt_device *xdev; + struct xhci_ring *ep_ring; + struct xhci_ep_ctx *ep_ctx; + int start_frame; + int num_tds, num_trbs, i; + int ret; + struct xhci_virt_ep *xep; + int ist; + + xdev = xhci->devs[slot_id]; + xep = &xhci->devs[slot_id]->eps[ep_index]; + ep_ring = xdev->eps[ep_index].ring; + ep_ctx = xhci_get_ep_ctx(xhci, xdev->out_ctx, ep_index); + + num_trbs = 0; + num_tds = urb->number_of_packets; + for (i = 0; i < num_tds; i++) + num_trbs += count_isoc_trbs_needed(urb, i); + + /* Check the ring to guarantee there is enough room for the whole urb. + * Do not insert any td of the urb to the ring if the check failed. + */ + ret = prepare_ring(xhci, ep_ring, GET_EP_CTX_STATE(ep_ctx), + num_trbs, mem_flags); + if (ret) + return ret; + + /* + * Check interval value. This should be done before we start to + * calculate the start frame value. + */ + check_interval(xhci, urb, ep_ctx); + + /* Calculate the start frame and put it in urb->start_frame. */ + if (HCC_CFC(xhci->hcc_params) && !list_empty(&ep_ring->td_list)) { + if (GET_EP_CTX_STATE(ep_ctx) == EP_STATE_RUNNING) { + urb->start_frame = xep->next_frame_id; + goto skip_start_over; + } + } + + start_frame = readl(&xhci->run_regs->microframe_index); + start_frame &= 0x3fff; + /* + * Round up to the next frame and consider the time before trb really + * gets scheduled by hardare. + */ + ist = HCS_IST(xhci->hcs_params2) & 0x7; + if (HCS_IST(xhci->hcs_params2) & (1 << 3)) + ist <<= 3; + start_frame += ist + XHCI_CFC_DELAY; + start_frame = roundup(start_frame, 8); + + /* + * Round up to the next ESIT (Endpoint Service Interval Time) if ESIT + * is greate than 8 microframes. + */ + if (urb->dev->speed == USB_SPEED_LOW || + urb->dev->speed == USB_SPEED_FULL) { + start_frame = roundup(start_frame, urb->interval << 3); + urb->start_frame = start_frame >> 3; + } else { + start_frame = roundup(start_frame, urb->interval); + urb->start_frame = start_frame; + } + +skip_start_over: + ep_ring->num_trbs_free_temp = ep_ring->num_trbs_free; + + return xhci_queue_isoc_tx(xhci, mem_flags, urb, slot_id, ep_index); +} + +/**** Command Ring Operations ****/ + +/* Generic function for queueing a command TRB on the command ring. + * Check to make sure there's room on the command ring for one command TRB. + * Also check that there's room reserved for commands that must not fail. + * If this is a command that must not fail, meaning command_must_succeed = TRUE, + * then only check for the number of reserved spots. + * Don't decrement xhci->cmd_ring_reserved_trbs after we've queued the TRB + * because the command event handler may want to resubmit a failed command. + */ +static int queue_command(struct xhci_hcd *xhci, struct xhci_command *cmd, + u32 field1, u32 field2, + u32 field3, u32 field4, bool command_must_succeed) +{ + int reserved_trbs = xhci->cmd_ring_reserved_trbs; + int ret; + + if ((xhci->xhc_state & XHCI_STATE_DYING) || + (xhci->xhc_state & XHCI_STATE_HALTED)) { + xhci_dbg(xhci, "xHCI dying or halted, can't queue_command\n"); + return -ESHUTDOWN; + } + + if (!command_must_succeed) + reserved_trbs++; + + ret = prepare_ring(xhci, xhci->cmd_ring, EP_STATE_RUNNING, + reserved_trbs, GFP_ATOMIC); + if (ret < 0) { + xhci_err(xhci, "ERR: No room for command on command ring\n"); + if (command_must_succeed) + xhci_err(xhci, "ERR: Reserved TRB counting for " + "unfailable commands failed.\n"); + return ret; + } + + cmd->command_trb = xhci->cmd_ring->enqueue; + + /* if there are no other commands queued we start the timeout timer */ + if (list_empty(&xhci->cmd_list)) { + xhci->current_cmd = cmd; + xhci_mod_cmd_timer(xhci, XHCI_CMD_DEFAULT_TIMEOUT); + } + + list_add_tail(&cmd->cmd_list, &xhci->cmd_list); + + queue_trb(xhci, xhci->cmd_ring, false, field1, field2, field3, + field4 | xhci->cmd_ring->cycle_state); + return 0; +} + +/* Queue a slot enable or disable request on the command ring */ +int xhci_queue_slot_control(struct xhci_hcd *xhci, struct xhci_command *cmd, + u32 trb_type, u32 slot_id) +{ + return queue_command(xhci, cmd, 0, 0, 0, + TRB_TYPE(trb_type) | SLOT_ID_FOR_TRB(slot_id), false); +} + +/* Queue an address device command TRB */ +int xhci_queue_address_device(struct xhci_hcd *xhci, struct xhci_command *cmd, + dma_addr_t in_ctx_ptr, u32 slot_id, enum xhci_setup_dev setup) +{ + return queue_command(xhci, cmd, lower_32_bits(in_ctx_ptr), + upper_32_bits(in_ctx_ptr), 0, + TRB_TYPE(TRB_ADDR_DEV) | SLOT_ID_FOR_TRB(slot_id) + | (setup == SETUP_CONTEXT_ONLY ? TRB_BSR : 0), false); +} + +int xhci_queue_vendor_command(struct xhci_hcd *xhci, struct xhci_command *cmd, + u32 field1, u32 field2, u32 field3, u32 field4) +{ + return queue_command(xhci, cmd, field1, field2, field3, field4, false); +} + +/* Queue a reset device command TRB */ +int xhci_queue_reset_device(struct xhci_hcd *xhci, struct xhci_command *cmd, + u32 slot_id) +{ + return queue_command(xhci, cmd, 0, 0, 0, + TRB_TYPE(TRB_RESET_DEV) | SLOT_ID_FOR_TRB(slot_id), + false); +} + +/* Queue a configure endpoint command TRB */ +int xhci_queue_configure_endpoint(struct xhci_hcd *xhci, + struct xhci_command *cmd, dma_addr_t in_ctx_ptr, + u32 slot_id, bool command_must_succeed) +{ + return queue_command(xhci, cmd, lower_32_bits(in_ctx_ptr), + upper_32_bits(in_ctx_ptr), 0, + TRB_TYPE(TRB_CONFIG_EP) | SLOT_ID_FOR_TRB(slot_id), + command_must_succeed); +} + +/* Queue an evaluate context command TRB */ +int xhci_queue_evaluate_context(struct xhci_hcd *xhci, struct xhci_command *cmd, + dma_addr_t in_ctx_ptr, u32 slot_id, bool command_must_succeed) +{ + return queue_command(xhci, cmd, lower_32_bits(in_ctx_ptr), + upper_32_bits(in_ctx_ptr), 0, + TRB_TYPE(TRB_EVAL_CONTEXT) | SLOT_ID_FOR_TRB(slot_id), + command_must_succeed); +} + +/* + * Suspend is set to indicate "Stop Endpoint Command" is being issued to stop + * activity on an endpoint that is about to be suspended. + */ +int xhci_queue_stop_endpoint(struct xhci_hcd *xhci, struct xhci_command *cmd, + int slot_id, unsigned int ep_index, int suspend) +{ + u32 trb_slot_id = SLOT_ID_FOR_TRB(slot_id); + u32 trb_ep_index = EP_ID_FOR_TRB(ep_index); + u32 type = TRB_TYPE(TRB_STOP_RING); + u32 trb_suspend = SUSPEND_PORT_FOR_TRB(suspend); + + return queue_command(xhci, cmd, 0, 0, 0, + trb_slot_id | trb_ep_index | type | trb_suspend, false); +} + +int xhci_queue_reset_ep(struct xhci_hcd *xhci, struct xhci_command *cmd, + int slot_id, unsigned int ep_index, + enum xhci_ep_reset_type reset_type) +{ + u32 trb_slot_id = SLOT_ID_FOR_TRB(slot_id); + u32 trb_ep_index = EP_ID_FOR_TRB(ep_index); + u32 type = TRB_TYPE(TRB_RESET_EP); + + if (reset_type == EP_SOFT_RESET) + type |= TRB_TSP; + + return queue_command(xhci, cmd, 0, 0, 0, + trb_slot_id | trb_ep_index | type, false); +} -- cgit v1.2.3