1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
|
# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
---
$id: http://devicetree.org/schemas/hwmon/ntc-thermistor.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: NTC thermistor temperature sensors
maintainers:
- Naveen Krishna Chatradhi <ch.naveen@samsung.com>
- Linus Walleij <linus.walleij@linaro.org>
description: |
Thermistors with negative temperature coefficient (NTC) are resistors that
vary in resistance in an often non-linear way in relation to temperature.
The negative temperature coefficient means that the resistance decreases
as the temperature rises. Since the relationship between resistance and
temperature is non-linear, software drivers most often need to use a look
up table and interpolation to get from resistance to temperature.
When used in practice, a thermistor is often connected between ground, a
pull-up resistor or/and a pull-down resistor and a fixed voltage like this:
+ e.g. 5V = pull-up voltage (puv)
|
+-+
| |
| | Pull-up resistor
| | (puo)
+-+
|-------------------------o
+-+ | ^
| |/ |
| / |
|/| Thermistor | Measured voltage (mv)
/ | | "connected ground"
/| | |
+-+ |
|-------------------------o
+-+ ^
| | |
| | Pull-down resistor | Measured voltage (mv)
| | (pdo) | "connected positive"
+-+ |
| |
| v
+ GND GND
The arrangements of where we measure the voltage over the thermistor are
called "connected ground" and "connected positive" and shall be understood as
the cases when either pull-up or pull-down resistance is zero.
If the pull-up resistance is 0 one end of the thermistor is connected to the
positive voltage and we get the thermistor on top of a pull-down resistor
and we take the measure between the thermistor and the pull-down resistor.
Conversely if the pull-down resistance is zero, one end of the thermistor is
connected to ground and we get the thermistor under the pull-up resistor
and we take the measure between the pull-up resistor and the thermistor.
We can use both pull-up and pull-down resistors at the same time, and then
the figure illustrates where the voltage will be measured for the "connected
ground" and "connected positive" cases.
properties:
$nodename:
pattern: "^thermistor(.*)?$"
compatible:
oneOf:
- const: epcos,b57330v2103
- const: epcos,b57891s0103
- const: murata,ncp15wb473
- const: murata,ncp18wb473
- const: murata,ncp21wb473
- const: murata,ncp03wb473
- const: murata,ncp15wl333
- const: murata,ncp03wf104
- const: murata,ncp15xh103
- const: samsung,1404-001221
# Deprecated "ntp," compatible strings
- const: ntc,ncp15wb473
deprecated: true
- const: ntc,ncp18wb473
deprecated: true
- const: ntc,ncp21wb473
deprecated: true
- const: ntc,ncp03wb473
deprecated: true
- const: ntc,ncp15wl333
deprecated: true
"#thermal-sensor-cells":
description: Thermal sensor cells if used for thermal sensoring.
const: 0
pullup-uv:
$ref: /schemas/types.yaml#/definitions/uint32
description: Pull-up voltage in micro volts. Must always be specified.
pullup-ohm:
$ref: /schemas/types.yaml#/definitions/uint32
description: Pull-up resistance in ohms. Must always be specified, even
if zero.
pulldown-ohm:
$ref: /schemas/types.yaml#/definitions/uint32
description: Pull-down resistance in ohms. Must always be specified, even
if zero.
connected-positive:
$ref: /schemas/types.yaml#/definitions/flag
description: Indicates how the thermistor is connected in series with
a pull-up and/or a pull-down resistor. See the description above for
an illustration. If this flag is NOT specified, the thermistor is assumed
to be connected-ground, which usually means a pull-down resistance of
zero but complex arrangements are possible.
# See /schemas/iio/adc/adc.yaml
io-channels:
maxItems: 1
description: IIO ADC channel to read the voltage over the resistor. Must
always be specified.
required:
- compatible
- pullup-uv
- pullup-ohm
- pulldown-ohm
- io-channels
additionalProperties: false
examples:
- |
thermistor0 {
compatible = "murata,ncp18wb473";
io-channels = <&gpadc 0x06>;
pullup-uv = <1800000>;
pullup-ohm = <220000>;
pulldown-ohm = <0>;
#thermal-sensor-cells = <0>;
};
|
