summaryrefslogtreecommitdiffstats
path: root/drivers/i2c/busses/i2c-npcm7xx.c
blob: 767dd15b3c8812f6f9e37956b3a4bd4799f1dca9 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
1001
1002
1003
1004
1005
1006
1007
1008
1009
1010
1011
1012
1013
1014
1015
1016
1017
1018
1019
1020
1021
1022
1023
1024
1025
1026
1027
1028
1029
1030
1031
1032
1033
1034
1035
1036
1037
1038
1039
1040
1041
1042
1043
1044
1045
1046
1047
1048
1049
1050
1051
1052
1053
1054
1055
1056
1057
1058
1059
1060
1061
1062
1063
1064
1065
1066
1067
1068
1069
1070
1071
1072
1073
1074
1075
1076
1077
1078
1079
1080
1081
1082
1083
1084
1085
1086
1087
1088
1089
1090
1091
1092
1093
1094
1095
1096
1097
1098
1099
1100
1101
1102
1103
1104
1105
1106
1107
1108
1109
1110
1111
1112
1113
1114
1115
1116
1117
1118
1119
1120
1121
1122
1123
1124
1125
1126
1127
1128
1129
1130
1131
1132
1133
1134
1135
1136
1137
1138
1139
1140
1141
1142
1143
1144
1145
1146
1147
1148
1149
1150
1151
1152
1153
1154
1155
1156
1157
1158
1159
1160
1161
1162
1163
1164
1165
1166
1167
1168
1169
1170
1171
1172
1173
1174
1175
1176
1177
1178
1179
1180
1181
1182
1183
1184
1185
1186
1187
1188
1189
1190
1191
1192
1193
1194
1195
1196
1197
1198
1199
1200
1201
1202
1203
1204
1205
1206
1207
1208
1209
1210
1211
1212
1213
1214
1215
1216
1217
1218
1219
1220
1221
1222
1223
1224
1225
1226
1227
1228
1229
1230
1231
1232
1233
1234
1235
1236
1237
1238
1239
1240
1241
1242
1243
1244
1245
1246
1247
1248
1249
1250
1251
1252
1253
1254
1255
1256
1257
1258
1259
1260
1261
1262
1263
1264
1265
1266
1267
1268
1269
1270
1271
1272
1273
1274
1275
1276
1277
1278
1279
1280
1281
1282
1283
1284
1285
1286
1287
1288
1289
1290
1291
1292
1293
1294
1295
1296
1297
1298
1299
1300
1301
1302
1303
1304
1305
1306
1307
1308
1309
1310
1311
1312
1313
1314
1315
1316
1317
1318
1319
1320
1321
1322
1323
1324
1325
1326
1327
1328
1329
1330
1331
1332
1333
1334
1335
1336
1337
1338
1339
1340
1341
1342
1343
1344
1345
1346
1347
1348
1349
1350
1351
1352
1353
1354
1355
1356
1357
1358
1359
1360
1361
1362
1363
1364
1365
1366
1367
1368
1369
1370
1371
1372
1373
1374
1375
1376
1377
1378
1379
1380
1381
1382
1383
1384
1385
1386
1387
1388
1389
1390
1391
1392
1393
1394
1395
1396
1397
1398
1399
1400
1401
1402
1403
1404
1405
1406
1407
1408
1409
1410
1411
1412
1413
1414
1415
1416
1417
1418
1419
1420
1421
1422
1423
1424
1425
1426
1427
1428
1429
1430
1431
1432
1433
1434
1435
1436
1437
1438
1439
1440
1441
1442
1443
1444
1445
1446
1447
1448
1449
1450
1451
1452
1453
1454
1455
1456
1457
1458
1459
1460
1461
1462
1463
1464
1465
1466
1467
1468
1469
1470
1471
1472
1473
1474
1475
1476
1477
1478
1479
1480
1481
1482
1483
1484
1485
1486
1487
1488
1489
1490
1491
1492
1493
1494
1495
1496
1497
1498
1499
1500
1501
1502
1503
1504
1505
1506
1507
1508
1509
1510
1511
1512
1513
1514
1515
1516
1517
1518
1519
1520
1521
1522
1523
1524
1525
1526
1527
1528
1529
1530
1531
1532
1533
1534
1535
1536
1537
1538
1539
1540
1541
1542
1543
1544
1545
1546
1547
1548
1549
1550
1551
1552
1553
1554
1555
1556
1557
1558
1559
1560
1561
1562
1563
1564
1565
1566
1567
1568
1569
1570
1571
1572
1573
1574
1575
1576
1577
1578
1579
1580
1581
1582
1583
1584
1585
1586
1587
1588
1589
1590
1591
1592
1593
1594
1595
1596
1597
1598
1599
1600
1601
1602
1603
1604
1605
1606
1607
1608
1609
1610
1611
1612
1613
1614
1615
1616
1617
1618
1619
1620
1621
1622
1623
1624
1625
1626
1627
1628
1629
1630
1631
1632
1633
1634
1635
1636
1637
1638
1639
1640
1641
1642
1643
1644
1645
1646
1647
1648
1649
1650
1651
1652
1653
1654
1655
1656
1657
1658
1659
1660
1661
1662
1663
1664
1665
1666
1667
1668
1669
1670
1671
1672
1673
1674
1675
1676
1677
1678
1679
1680
1681
1682
1683
1684
1685
1686
1687
1688
1689
1690
1691
1692
1693
1694
1695
1696
1697
1698
1699
1700
1701
1702
1703
1704
1705
1706
1707
1708
1709
1710
1711
1712
1713
1714
1715
1716
1717
1718
1719
1720
1721
1722
1723
1724
1725
1726
1727
1728
1729
1730
1731
1732
1733
1734
1735
1736
1737
1738
1739
1740
1741
1742
1743
1744
1745
1746
1747
1748
1749
1750
1751
1752
1753
1754
1755
1756
1757
1758
1759
1760
1761
1762
1763
1764
1765
1766
1767
1768
1769
1770
1771
1772
1773
1774
1775
1776
1777
1778
1779
1780
1781
1782
1783
1784
1785
1786
1787
1788
1789
1790
1791
1792
1793
1794
1795
1796
1797
1798
1799
1800
1801
1802
1803
1804
1805
1806
1807
1808
1809
1810
1811
1812
1813
1814
1815
1816
1817
1818
1819
1820
1821
1822
1823
1824
1825
1826
1827
1828
1829
1830
1831
1832
1833
1834
1835
1836
1837
1838
1839
1840
1841
1842
1843
1844
1845
1846
1847
1848
1849
1850
1851
1852
1853
1854
1855
1856
1857
1858
1859
1860
1861
1862
1863
1864
1865
1866
1867
1868
1869
1870
1871
1872
1873
1874
1875
1876
1877
1878
1879
1880
1881
1882
1883
1884
1885
1886
1887
1888
1889
1890
1891
1892
1893
1894
1895
1896
1897
1898
1899
1900
1901
1902
1903
1904
1905
1906
1907
1908
1909
1910
1911
1912
1913
1914
1915
1916
1917
1918
1919
1920
1921
1922
1923
1924
1925
1926
1927
1928
1929
1930
1931
1932
1933
1934
1935
1936
1937
1938
1939
1940
1941
1942
1943
1944
1945
1946
1947
1948
1949
1950
1951
1952
1953
1954
1955
1956
1957
1958
1959
1960
1961
1962
1963
1964
1965
1966
1967
1968
1969
1970
1971
1972
1973
1974
1975
1976
1977
1978
1979
1980
1981
1982
1983
1984
1985
1986
1987
1988
1989
1990
1991
1992
1993
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
2005
2006
2007
2008
2009
2010
2011
2012
2013
2014
2015
2016
2017
2018
2019
2020
2021
2022
2023
2024
2025
2026
2027
2028
2029
2030
2031
2032
2033
2034
2035
2036
2037
2038
2039
2040
2041
2042
2043
2044
2045
2046
2047
2048
2049
2050
2051
2052
2053
2054
2055
2056
2057
2058
2059
2060
2061
2062
2063
2064
2065
2066
2067
2068
2069
2070
2071
2072
2073
2074
2075
2076
2077
2078
2079
2080
2081
2082
2083
2084
2085
2086
2087
2088
2089
2090
2091
2092
2093
2094
2095
2096
2097
2098
2099
2100
2101
2102
2103
2104
2105
2106
2107
2108
2109
2110
2111
2112
2113
2114
2115
2116
2117
2118
2119
2120
2121
2122
2123
2124
2125
2126
2127
2128
2129
2130
2131
2132
2133
2134
2135
2136
2137
2138
2139
2140
2141
2142
2143
2144
2145
2146
2147
2148
2149
2150
2151
2152
2153
2154
2155
2156
2157
2158
2159
2160
2161
2162
2163
2164
2165
2166
2167
2168
2169
2170
2171
2172
2173
2174
2175
2176
2177
2178
2179
2180
2181
2182
2183
2184
2185
2186
2187
2188
2189
2190
2191
2192
2193
2194
2195
2196
2197
2198
2199
2200
2201
2202
2203
2204
2205
2206
2207
2208
2209
2210
2211
2212
2213
2214
2215
2216
2217
2218
2219
2220
2221
2222
2223
2224
2225
2226
2227
2228
2229
2230
2231
2232
2233
2234
2235
2236
2237
2238
2239
2240
2241
2242
2243
2244
2245
2246
2247
2248
2249
2250
2251
2252
2253
2254
2255
2256
2257
2258
2259
2260
2261
2262
2263
2264
2265
2266
2267
2268
2269
2270
2271
2272
2273
2274
2275
2276
2277
2278
2279
2280
2281
2282
2283
2284
2285
2286
2287
2288
2289
2290
2291
2292
2293
2294
2295
2296
2297
2298
2299
2300
2301
2302
2303
2304
2305
2306
2307
2308
2309
2310
2311
2312
2313
2314
2315
2316
2317
2318
2319
2320
2321
2322
2323
2324
2325
2326
2327
2328
2329
2330
2331
2332
2333
2334
2335
2336
2337
2338
2339
2340
2341
2342
2343
2344
2345
2346
2347
2348
2349
2350
2351
2352
2353
2354
2355
2356
2357
2358
2359
2360
2361
2362
2363
2364
2365
2366
2367
2368
2369
2370
2371
2372
2373
2374
2375
2376
2377
2378
2379
2380
2381
2382
2383
2384
2385
2386
2387
2388
2389
2390
2391
2392
2393
2394
2395
2396
2397
2398
2399
2400
2401
2402
2403
2404
2405
2406
2407
2408
2409
2410
2411
2412
2413
2414
2415
2416
2417
2418
// SPDX-License-Identifier: GPL-2.0
/*
 * Nuvoton NPCM7xx I2C Controller driver
 *
 * Copyright (C) 2020 Nuvoton Technologies tali.perry@nuvoton.com
 */
#include <linux/bitfield.h>
#include <linux/clk.h>
#include <linux/debugfs.h>
#include <linux/errno.h>
#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/iopoll.h>
#include <linux/irq.h>
#include <linux/jiffies.h>
#include <linux/kernel.h>
#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>

enum i2c_mode {
	I2C_MASTER,
	I2C_SLAVE,
};

/*
 * External I2C Interface driver xfer indication values, which indicate status
 * of the bus.
 */
enum i2c_state_ind {
	I2C_NO_STATUS_IND = 0,
	I2C_SLAVE_RCV_IND,
	I2C_SLAVE_XMIT_IND,
	I2C_SLAVE_XMIT_MISSING_DATA_IND,
	I2C_SLAVE_RESTART_IND,
	I2C_SLAVE_DONE_IND,
	I2C_MASTER_DONE_IND,
	I2C_NACK_IND,
	I2C_BUS_ERR_IND,
	I2C_WAKE_UP_IND,
	I2C_BLOCK_BYTES_ERR_IND,
	I2C_SLAVE_RCV_MISSING_DATA_IND,
};

/*
 * Operation type values (used to define the operation currently running)
 * module is interrupt driven, on each interrupt the current operation is
 * checked to see if the module is currently reading or writing.
 */
enum i2c_oper {
	I2C_NO_OPER = 0,
	I2C_WRITE_OPER,
	I2C_READ_OPER,
};

/* I2C Bank (module had 2 banks of registers) */
enum i2c_bank {
	I2C_BANK_0 = 0,
	I2C_BANK_1,
};

/* Internal I2C states values (for the I2C module state machine). */
enum i2c_state {
	I2C_DISABLE = 0,
	I2C_IDLE,
	I2C_MASTER_START,
	I2C_SLAVE_MATCH,
	I2C_OPER_STARTED,
	I2C_STOP_PENDING,
};

#if IS_ENABLED(CONFIG_I2C_SLAVE)
/* Module supports setting multiple own slave addresses */
enum i2c_addr {
	I2C_SLAVE_ADDR1 = 0,
	I2C_SLAVE_ADDR2,
	I2C_SLAVE_ADDR3,
	I2C_SLAVE_ADDR4,
	I2C_SLAVE_ADDR5,
	I2C_SLAVE_ADDR6,
	I2C_SLAVE_ADDR7,
	I2C_SLAVE_ADDR8,
	I2C_SLAVE_ADDR9,
	I2C_SLAVE_ADDR10,
	I2C_GC_ADDR,
	I2C_ARP_ADDR,
};
#endif

/* init register and default value required to enable module */
#define NPCM_I2CSEGCTL			0xE4

/* Common regs */
#define NPCM_I2CSDA			0x00
#define NPCM_I2CST			0x02
#define NPCM_I2CCST			0x04
#define NPCM_I2CCTL1			0x06
#define NPCM_I2CADDR1			0x08
#define NPCM_I2CCTL2			0x0A
#define NPCM_I2CADDR2			0x0C
#define NPCM_I2CCTL3			0x0E
#define NPCM_I2CCST2			0x18
#define NPCM_I2CCST3			0x19
#define I2C_VER				0x1F

/*BANK0 regs*/
#define NPCM_I2CADDR3			0x10
#define NPCM_I2CADDR7			0x11
#define NPCM_I2CADDR4			0x12
#define NPCM_I2CADDR8			0x13
#define NPCM_I2CADDR5			0x14
#define NPCM_I2CADDR9			0x15
#define NPCM_I2CADDR6			0x16
#define NPCM_I2CADDR10			0x17

#if IS_ENABLED(CONFIG_I2C_SLAVE)
/*
 * npcm_i2caddr array:
 * The module supports having multiple own slave addresses.
 * Since the addr regs are sprinkled all over the address space,
 * use this array to get the address or each register.
 */
#define I2C_NUM_OWN_ADDR 2
#define I2C_NUM_OWN_ADDR_SUPPORTED 2

static const int npcm_i2caddr[I2C_NUM_OWN_ADDR] = {
	NPCM_I2CADDR1, NPCM_I2CADDR2,
};
#endif

#define NPCM_I2CCTL4			0x1A
#define NPCM_I2CCTL5			0x1B
#define NPCM_I2CSCLLT			0x1C /* SCL Low Time */
#define NPCM_I2CFIF_CTL			0x1D /* FIFO Control */
#define NPCM_I2CSCLHT			0x1E /* SCL High Time */

/* BANK 1 regs */
#define NPCM_I2CFIF_CTS			0x10 /* Both FIFOs Control and Status */
#define NPCM_I2CTXF_CTL			0x12 /* Tx-FIFO Control */
#define NPCM_I2CT_OUT			0x14 /* Bus T.O. */
#define NPCM_I2CPEC			0x16 /* PEC Data */
#define NPCM_I2CTXF_STS			0x1A /* Tx-FIFO Status */
#define NPCM_I2CRXF_STS			0x1C /* Rx-FIFO Status */
#define NPCM_I2CRXF_CTL			0x1E /* Rx-FIFO Control */

/* NPCM_I2CST reg fields */
#define NPCM_I2CST_XMIT			BIT(0)
#define NPCM_I2CST_MASTER		BIT(1)
#define NPCM_I2CST_NMATCH		BIT(2)
#define NPCM_I2CST_STASTR		BIT(3)
#define NPCM_I2CST_NEGACK		BIT(4)
#define NPCM_I2CST_BER			BIT(5)
#define NPCM_I2CST_SDAST		BIT(6)
#define NPCM_I2CST_SLVSTP		BIT(7)

/* NPCM_I2CCST reg fields */
#define NPCM_I2CCST_BUSY		BIT(0)
#define NPCM_I2CCST_BB			BIT(1)
#define NPCM_I2CCST_MATCH		BIT(2)
#define NPCM_I2CCST_GCMATCH		BIT(3)
#define NPCM_I2CCST_TSDA		BIT(4)
#define NPCM_I2CCST_TGSCL		BIT(5)
#define NPCM_I2CCST_MATCHAF		BIT(6)
#define NPCM_I2CCST_ARPMATCH		BIT(7)

/* NPCM_I2CCTL1 reg fields */
#define NPCM_I2CCTL1_START		BIT(0)
#define NPCM_I2CCTL1_STOP		BIT(1)
#define NPCM_I2CCTL1_INTEN		BIT(2)
#define NPCM_I2CCTL1_EOBINTE		BIT(3)
#define NPCM_I2CCTL1_ACK		BIT(4)
#define NPCM_I2CCTL1_GCMEN		BIT(5)
#define NPCM_I2CCTL1_NMINTE		BIT(6)
#define NPCM_I2CCTL1_STASTRE		BIT(7)

/* RW1S fields (inside a RW reg): */
#define NPCM_I2CCTL1_RWS   \
	(NPCM_I2CCTL1_START | NPCM_I2CCTL1_STOP | NPCM_I2CCTL1_ACK)

/* npcm_i2caddr reg fields */
#define NPCM_I2CADDR_A			GENMASK(6, 0)
#define NPCM_I2CADDR_SAEN		BIT(7)

/* NPCM_I2CCTL2 reg fields */
#define I2CCTL2_ENABLE			BIT(0)
#define I2CCTL2_SCLFRQ6_0		GENMASK(7, 1)

/* NPCM_I2CCTL3 reg fields */
#define I2CCTL3_SCLFRQ8_7		GENMASK(1, 0)
#define I2CCTL3_ARPMEN			BIT(2)
#define I2CCTL3_IDL_START		BIT(3)
#define I2CCTL3_400K_MODE		BIT(4)
#define I2CCTL3_BNK_SEL			BIT(5)
#define I2CCTL3_SDA_LVL			BIT(6)
#define I2CCTL3_SCL_LVL			BIT(7)

/* NPCM_I2CCST2 reg fields */
#define NPCM_I2CCST2_MATCHA1F		BIT(0)
#define NPCM_I2CCST2_MATCHA2F		BIT(1)
#define NPCM_I2CCST2_MATCHA3F		BIT(2)
#define NPCM_I2CCST2_MATCHA4F		BIT(3)
#define NPCM_I2CCST2_MATCHA5F		BIT(4)
#define NPCM_I2CCST2_MATCHA6F		BIT(5)
#define NPCM_I2CCST2_MATCHA7F		BIT(5)
#define NPCM_I2CCST2_INTSTS		BIT(7)

/* NPCM_I2CCST3 reg fields */
#define NPCM_I2CCST3_MATCHA8F		BIT(0)
#define NPCM_I2CCST3_MATCHA9F		BIT(1)
#define NPCM_I2CCST3_MATCHA10F		BIT(2)
#define NPCM_I2CCST3_EO_BUSY		BIT(7)

/* NPCM_I2CCTL4 reg fields */
#define I2CCTL4_HLDT			GENMASK(5, 0)
#define I2CCTL4_LVL_WE			BIT(7)

/* NPCM_I2CCTL5 reg fields */
#define I2CCTL5_DBNCT			GENMASK(3, 0)

/* NPCM_I2CFIF_CTS reg fields */
#define NPCM_I2CFIF_CTS_RXF_TXE		BIT(1)
#define NPCM_I2CFIF_CTS_RFTE_IE		BIT(3)
#define NPCM_I2CFIF_CTS_CLR_FIFO	BIT(6)
#define NPCM_I2CFIF_CTS_SLVRSTR		BIT(7)

/* NPCM_I2CTXF_CTL reg field */
#define NPCM_I2CTXF_CTL_THR_TXIE	BIT(6)

/* NPCM_I2CT_OUT reg fields */
#define NPCM_I2CT_OUT_TO_CKDIV		GENMASK(5, 0)
#define NPCM_I2CT_OUT_T_OUTIE		BIT(6)
#define NPCM_I2CT_OUT_T_OUTST		BIT(7)

/* NPCM_I2CTXF_STS reg fields */
#define NPCM_I2CTXF_STS_TX_THST		BIT(6)

/* NPCM_I2CRXF_STS reg fields */
#define NPCM_I2CRXF_STS_RX_THST		BIT(6)

/* NPCM_I2CFIF_CTL reg fields */
#define NPCM_I2CFIF_CTL_FIFO_EN		BIT(4)

/* NPCM_I2CRXF_CTL reg fields */
#define NPCM_I2CRXF_CTL_THR_RXIE	BIT(6)

#define MAX_I2C_HW_FIFO_SIZE		32

/* I2C_VER reg fields */
#define I2C_VER_VERSION			GENMASK(6, 0)
#define I2C_VER_FIFO_EN			BIT(7)

/* stall/stuck timeout in us */
#define DEFAULT_STALL_COUNT		25

/* SCLFRQ field position */
#define SCLFRQ_0_TO_6			GENMASK(6, 0)
#define SCLFRQ_7_TO_8			GENMASK(8, 7)

/* supported clk settings. values in Hz. */
#define I2C_FREQ_MIN_HZ			10000
#define I2C_FREQ_MAX_HZ			I2C_MAX_FAST_MODE_PLUS_FREQ

struct npcm_i2c_data {
	u8 fifo_size;
	u32 segctl_init_val;
	u8 txf_sts_tx_bytes;
	u8 rxf_sts_rx_bytes;
	u8 rxf_ctl_last_pec;
};

static const struct npcm_i2c_data npxm7xx_i2c_data = {
	.fifo_size = 16,
	.segctl_init_val = 0x0333F000,
	.txf_sts_tx_bytes = GENMASK(4, 0),
	.rxf_sts_rx_bytes = GENMASK(4, 0),
	.rxf_ctl_last_pec = BIT(5),
};

static const struct npcm_i2c_data npxm8xx_i2c_data = {
	.fifo_size = 32,
	.segctl_init_val = 0x9333F000,
	.txf_sts_tx_bytes = GENMASK(5, 0),
	.rxf_sts_rx_bytes = GENMASK(5, 0),
	.rxf_ctl_last_pec = BIT(7),
};

/* Status of one I2C module */
struct npcm_i2c {
	struct i2c_adapter adap;
	struct device *dev;
	unsigned char __iomem *reg;
	const struct npcm_i2c_data *data;
	spinlock_t lock;   /* IRQ synchronization */
	struct completion cmd_complete;
	int cmd_err;
	struct i2c_msg *msgs;
	int msgs_num;
	int num;
	u32 apb_clk;
	struct i2c_bus_recovery_info rinfo;
	enum i2c_state state;
	enum i2c_oper operation;
	enum i2c_mode master_or_slave;
	enum i2c_state_ind stop_ind;
	u8 dest_addr;
	u8 *rd_buf;
	u16 rd_size;
	u16 rd_ind;
	u8 *wr_buf;
	u16 wr_size;
	u16 wr_ind;
	bool fifo_use;
	u16 PEC_mask; /* PEC bit mask per slave address */
	bool PEC_use;
	bool read_block_use;
	unsigned long int_time_stamp;
	unsigned long bus_freq; /* in Hz */
#if IS_ENABLED(CONFIG_I2C_SLAVE)
	u8 own_slave_addr;
	struct i2c_client *slave;
	int slv_rd_size;
	int slv_rd_ind;
	int slv_wr_size;
	int slv_wr_ind;
	u8 slv_rd_buf[MAX_I2C_HW_FIFO_SIZE];
	u8 slv_wr_buf[MAX_I2C_HW_FIFO_SIZE];
#endif
	struct dentry *debugfs; /* debugfs device directory */
	u64 ber_cnt;
	u64 rec_succ_cnt;
	u64 rec_fail_cnt;
	u64 nack_cnt;
	u64 timeout_cnt;
	u64 tx_complete_cnt;
};

static inline void npcm_i2c_select_bank(struct npcm_i2c *bus,
					enum i2c_bank bank)
{
	u8 i2cctl3 = ioread8(bus->reg + NPCM_I2CCTL3);

	if (bank == I2C_BANK_0)
		i2cctl3 = i2cctl3 & ~I2CCTL3_BNK_SEL;
	else
		i2cctl3 = i2cctl3 | I2CCTL3_BNK_SEL;
	iowrite8(i2cctl3, bus->reg + NPCM_I2CCTL3);
}

static void npcm_i2c_init_params(struct npcm_i2c *bus)
{
	bus->stop_ind = I2C_NO_STATUS_IND;
	bus->rd_size = 0;
	bus->wr_size = 0;
	bus->rd_ind = 0;
	bus->wr_ind = 0;
	bus->read_block_use = false;
	bus->int_time_stamp = 0;
	bus->PEC_use = false;
	bus->PEC_mask = 0;
#if IS_ENABLED(CONFIG_I2C_SLAVE)
	if (bus->slave)
		bus->master_or_slave = I2C_SLAVE;
#endif
}

static inline void npcm_i2c_wr_byte(struct npcm_i2c *bus, u8 data)
{
	iowrite8(data, bus->reg + NPCM_I2CSDA);
}

static inline u8 npcm_i2c_rd_byte(struct npcm_i2c *bus)
{
	return ioread8(bus->reg + NPCM_I2CSDA);
}

static int npcm_i2c_get_SCL(struct i2c_adapter *_adap)
{
	struct npcm_i2c *bus = container_of(_adap, struct npcm_i2c, adap);

	return !!(I2CCTL3_SCL_LVL & ioread8(bus->reg + NPCM_I2CCTL3));
}

static int npcm_i2c_get_SDA(struct i2c_adapter *_adap)
{
	struct npcm_i2c *bus = container_of(_adap, struct npcm_i2c, adap);

	return !!(I2CCTL3_SDA_LVL & ioread8(bus->reg + NPCM_I2CCTL3));
}

static inline u16 npcm_i2c_get_index(struct npcm_i2c *bus)
{
	if (bus->operation == I2C_READ_OPER)
		return bus->rd_ind;
	if (bus->operation == I2C_WRITE_OPER)
		return bus->wr_ind;
	return 0;
}

/* quick protocol (just address) */
static inline bool npcm_i2c_is_quick(struct npcm_i2c *bus)
{
	return bus->wr_size == 0 && bus->rd_size == 0;
}

static void npcm_i2c_disable(struct npcm_i2c *bus)
{
	u8 i2cctl2;

#if IS_ENABLED(CONFIG_I2C_SLAVE)
	int i;

	/* Slave addresses removal */
	for (i = I2C_SLAVE_ADDR1; i < I2C_NUM_OWN_ADDR_SUPPORTED; i++)
		iowrite8(0, bus->reg + npcm_i2caddr[i]);

#endif
	/* Disable module */
	i2cctl2 = ioread8(bus->reg + NPCM_I2CCTL2);
	i2cctl2 = i2cctl2 & ~I2CCTL2_ENABLE;
	iowrite8(i2cctl2, bus->reg + NPCM_I2CCTL2);

	bus->state = I2C_DISABLE;
}

static void npcm_i2c_enable(struct npcm_i2c *bus)
{
	u8 i2cctl2 = ioread8(bus->reg + NPCM_I2CCTL2);

	i2cctl2 = i2cctl2 | I2CCTL2_ENABLE;
	iowrite8(i2cctl2, bus->reg + NPCM_I2CCTL2);
	bus->state = I2C_IDLE;
}

/* enable\disable end of busy (EOB) interrupts */
static inline void npcm_i2c_eob_int(struct npcm_i2c *bus, bool enable)
{
	u8 val;

	/* Clear EO_BUSY pending bit: */
	val = ioread8(bus->reg + NPCM_I2CCST3);
	val = val | NPCM_I2CCST3_EO_BUSY;
	iowrite8(val, bus->reg + NPCM_I2CCST3);

	val = ioread8(bus->reg + NPCM_I2CCTL1);
	val &= ~NPCM_I2CCTL1_RWS;
	if (enable)
		val |= NPCM_I2CCTL1_EOBINTE;
	else
		val &= ~NPCM_I2CCTL1_EOBINTE;
	iowrite8(val, bus->reg + NPCM_I2CCTL1);
}

static inline bool npcm_i2c_tx_fifo_empty(struct npcm_i2c *bus)
{
	u8 tx_fifo_sts;

	tx_fifo_sts = ioread8(bus->reg + NPCM_I2CTXF_STS);
	/* check if TX FIFO is not empty */
	if ((tx_fifo_sts & bus->data->txf_sts_tx_bytes) == 0)
		return false;

	/* check if TX FIFO status bit is set: */
	return !!FIELD_GET(NPCM_I2CTXF_STS_TX_THST, tx_fifo_sts);
}

static inline bool npcm_i2c_rx_fifo_full(struct npcm_i2c *bus)
{
	u8 rx_fifo_sts;

	rx_fifo_sts = ioread8(bus->reg + NPCM_I2CRXF_STS);
	/* check if RX FIFO is not empty: */
	if ((rx_fifo_sts & bus->data->rxf_sts_rx_bytes) == 0)
		return false;

	/* check if rx fifo full status is set: */
	return !!FIELD_GET(NPCM_I2CRXF_STS_RX_THST, rx_fifo_sts);
}

static inline void npcm_i2c_clear_fifo_int(struct npcm_i2c *bus)
{
	u8 val;

	val = ioread8(bus->reg + NPCM_I2CFIF_CTS);
	val = (val & NPCM_I2CFIF_CTS_SLVRSTR) | NPCM_I2CFIF_CTS_RXF_TXE;
	iowrite8(val, bus->reg + NPCM_I2CFIF_CTS);
}

static inline void npcm_i2c_clear_tx_fifo(struct npcm_i2c *bus)
{
	u8 val;

	val = ioread8(bus->reg + NPCM_I2CTXF_STS);
	val = val | NPCM_I2CTXF_STS_TX_THST;
	iowrite8(val, bus->reg + NPCM_I2CTXF_STS);
}

static inline void npcm_i2c_clear_rx_fifo(struct npcm_i2c *bus)
{
	u8 val;

	val = ioread8(bus->reg + NPCM_I2CRXF_STS);
	val = val | NPCM_I2CRXF_STS_RX_THST;
	iowrite8(val, bus->reg + NPCM_I2CRXF_STS);
}

static void npcm_i2c_int_enable(struct npcm_i2c *bus, bool enable)
{
	u8 val;

	val = ioread8(bus->reg + NPCM_I2CCTL1);
	val &= ~NPCM_I2CCTL1_RWS;
	if (enable)
		val |= NPCM_I2CCTL1_INTEN;
	else
		val &= ~NPCM_I2CCTL1_INTEN;
	iowrite8(val, bus->reg + NPCM_I2CCTL1);
}

static inline void npcm_i2c_master_start(struct npcm_i2c *bus)
{
	u8 val;

	val = ioread8(bus->reg + NPCM_I2CCTL1);
	val &= ~(NPCM_I2CCTL1_STOP | NPCM_I2CCTL1_ACK);
	val |= NPCM_I2CCTL1_START;
	iowrite8(val, bus->reg + NPCM_I2CCTL1);
}

static inline void npcm_i2c_master_stop(struct npcm_i2c *bus)
{
	u8 val;

	/*
	 * override HW issue: I2C may fail to supply stop condition in Master
	 * Write operation.
	 * Need to delay at least 5 us from the last int, before issueing a stop
	 */
	udelay(10); /* function called from interrupt, can't sleep */
	val = ioread8(bus->reg + NPCM_I2CCTL1);
	val &= ~(NPCM_I2CCTL1_START | NPCM_I2CCTL1_ACK);
	val |= NPCM_I2CCTL1_STOP;
	iowrite8(val, bus->reg + NPCM_I2CCTL1);

	if (!bus->fifo_use)
		return;

	npcm_i2c_select_bank(bus, I2C_BANK_1);

	if (bus->operation == I2C_READ_OPER)
		npcm_i2c_clear_rx_fifo(bus);
	else
		npcm_i2c_clear_tx_fifo(bus);
	npcm_i2c_clear_fifo_int(bus);
	iowrite8(0, bus->reg + NPCM_I2CTXF_CTL);
}

static inline void npcm_i2c_stall_after_start(struct npcm_i2c *bus, bool stall)
{
	u8 val;

	val = ioread8(bus->reg + NPCM_I2CCTL1);
	val &= ~NPCM_I2CCTL1_RWS;
	if (stall)
		val |= NPCM_I2CCTL1_STASTRE;
	else
		val &= ~NPCM_I2CCTL1_STASTRE;
	iowrite8(val, bus->reg + NPCM_I2CCTL1);
}

static inline void npcm_i2c_nack(struct npcm_i2c *bus)
{
	u8 val;

	val = ioread8(bus->reg + NPCM_I2CCTL1);
	val &= ~(NPCM_I2CCTL1_STOP | NPCM_I2CCTL1_START);
	val |= NPCM_I2CCTL1_ACK;
	iowrite8(val, bus->reg + NPCM_I2CCTL1);
}

static inline void npcm_i2c_clear_master_status(struct npcm_i2c *bus)
{
	u8 val;

	/* Clear NEGACK, STASTR and BER bits */
	val = NPCM_I2CST_BER | NPCM_I2CST_NEGACK | NPCM_I2CST_STASTR;
	iowrite8(val, bus->reg + NPCM_I2CST);
}

#if IS_ENABLED(CONFIG_I2C_SLAVE)
static void npcm_i2c_slave_int_enable(struct npcm_i2c *bus, bool enable)
{
	u8 i2cctl1;

	/* enable interrupt on slave match: */
	i2cctl1 = ioread8(bus->reg + NPCM_I2CCTL1);
	i2cctl1 &= ~NPCM_I2CCTL1_RWS;
	if (enable)
		i2cctl1 |= NPCM_I2CCTL1_NMINTE;
	else
		i2cctl1 &= ~NPCM_I2CCTL1_NMINTE;
	iowrite8(i2cctl1, bus->reg + NPCM_I2CCTL1);
}

static int npcm_i2c_slave_enable(struct npcm_i2c *bus, enum i2c_addr addr_type,
				 u8 addr, bool enable)
{
	u8 i2cctl1;
	u8 i2cctl3;
	u8 sa_reg;

	sa_reg = (addr & 0x7F) | FIELD_PREP(NPCM_I2CADDR_SAEN, enable);
	if (addr_type == I2C_GC_ADDR) {
		i2cctl1 = ioread8(bus->reg + NPCM_I2CCTL1);
		if (enable)
			i2cctl1 |= NPCM_I2CCTL1_GCMEN;
		else
			i2cctl1 &= ~NPCM_I2CCTL1_GCMEN;
		iowrite8(i2cctl1, bus->reg + NPCM_I2CCTL1);
		return 0;
	} else if (addr_type == I2C_ARP_ADDR) {
		i2cctl3 = ioread8(bus->reg + NPCM_I2CCTL3);
		if (enable)
			i2cctl3 |= I2CCTL3_ARPMEN;
		else
			i2cctl3 &= ~I2CCTL3_ARPMEN;
		iowrite8(i2cctl3, bus->reg + NPCM_I2CCTL3);
		return 0;
	}
	if (addr_type > I2C_SLAVE_ADDR2 && addr_type <= I2C_SLAVE_ADDR10)
		dev_err(bus->dev, "try to enable more than 2 SA not supported\n");

	if (addr_type >= I2C_ARP_ADDR)
		return -EFAULT;

	/* Set and enable the address */
	iowrite8(sa_reg, bus->reg + npcm_i2caddr[addr_type]);
	npcm_i2c_slave_int_enable(bus, enable);

	return 0;
}
#endif

static void npcm_i2c_reset(struct npcm_i2c *bus)
{
	/*
	 * Save I2CCTL1 relevant bits. It is being cleared when the module
	 *  is disabled.
	 */
	u8 i2cctl1;
#if IS_ENABLED(CONFIG_I2C_SLAVE)
	u8 addr;
#endif

	i2cctl1 = ioread8(bus->reg + NPCM_I2CCTL1);

	npcm_i2c_disable(bus);
	npcm_i2c_enable(bus);

	/* Restore NPCM_I2CCTL1 Status */
	i2cctl1 &= ~NPCM_I2CCTL1_RWS;
	iowrite8(i2cctl1, bus->reg + NPCM_I2CCTL1);

	/* Clear BB (BUS BUSY) bit */
	iowrite8(NPCM_I2CCST_BB, bus->reg + NPCM_I2CCST);
	iowrite8(0xFF, bus->reg + NPCM_I2CST);

	/* Clear and disable EOB */
	npcm_i2c_eob_int(bus, false);

	/* Clear all fifo bits: */
	iowrite8(NPCM_I2CFIF_CTS_CLR_FIFO, bus->reg + NPCM_I2CFIF_CTS);

#if IS_ENABLED(CONFIG_I2C_SLAVE)
	if (bus->slave) {
		addr = bus->slave->addr;
		npcm_i2c_slave_enable(bus, I2C_SLAVE_ADDR1, addr, true);
	}
#endif

	/* Clear status bits for spurious interrupts */
	npcm_i2c_clear_master_status(bus);

	bus->state = I2C_IDLE;
}

static inline bool npcm_i2c_is_master(struct npcm_i2c *bus)
{
	return !!FIELD_GET(NPCM_I2CST_MASTER, ioread8(bus->reg + NPCM_I2CST));
}

static void npcm_i2c_callback(struct npcm_i2c *bus,
			      enum i2c_state_ind op_status, u16 info)
{
	struct i2c_msg *msgs;
	int msgs_num;
	bool do_complete = false;

	msgs = bus->msgs;
	msgs_num = bus->msgs_num;
	/*
	 * check that transaction was not timed-out, and msgs still
	 * holds a valid value.
	 */
	if (!msgs)
		return;

	if (completion_done(&bus->cmd_complete))
		return;

	switch (op_status) {
	case I2C_MASTER_DONE_IND:
		bus->cmd_err = bus->msgs_num;
		if (bus->tx_complete_cnt < ULLONG_MAX)
			bus->tx_complete_cnt++;
		fallthrough;
	case I2C_BLOCK_BYTES_ERR_IND:
		/* Master tx finished and all transmit bytes were sent */
		if (bus->msgs) {
			if (msgs[0].flags & I2C_M_RD)
				msgs[0].len = info;
			else if (msgs_num == 2 &&
				 msgs[1].flags & I2C_M_RD)
				msgs[1].len = info;
		}
		do_complete = true;
		break;
	case I2C_NACK_IND:
		/* MASTER transmit got a NACK before tx all bytes */
		bus->cmd_err = -ENXIO;
		do_complete = true;
		break;
	case I2C_BUS_ERR_IND:
		/* Bus error */
		bus->cmd_err = -EAGAIN;
		do_complete = true;
		break;
	case I2C_WAKE_UP_IND:
		/* I2C wake up */
		break;
	default:
		break;
	}

	bus->operation = I2C_NO_OPER;
#if IS_ENABLED(CONFIG_I2C_SLAVE)
	if (bus->slave)
		bus->master_or_slave = I2C_SLAVE;
#endif
	if (do_complete)
		complete(&bus->cmd_complete);
}

static u8 npcm_i2c_fifo_usage(struct npcm_i2c *bus)
{
	if (bus->operation == I2C_WRITE_OPER)
		return (bus->data->txf_sts_tx_bytes &
			ioread8(bus->reg + NPCM_I2CTXF_STS));
	if (bus->operation == I2C_READ_OPER)
		return (bus->data->rxf_sts_rx_bytes &
			ioread8(bus->reg + NPCM_I2CRXF_STS));
	return 0;
}

static void npcm_i2c_write_to_fifo_master(struct npcm_i2c *bus, u16 max_bytes)
{
	u8 size_free_fifo;

	/*
	 * Fill the FIFO, while the FIFO is not full and there are more bytes
	 * to write
	 */
	size_free_fifo = bus->data->fifo_size - npcm_i2c_fifo_usage(bus);
	while (max_bytes-- && size_free_fifo) {
		if (bus->wr_ind < bus->wr_size)
			npcm_i2c_wr_byte(bus, bus->wr_buf[bus->wr_ind++]);
		else
			npcm_i2c_wr_byte(bus, 0xFF);
		size_free_fifo = bus->data->fifo_size - npcm_i2c_fifo_usage(bus);
	}
}

/*
 * npcm_i2c_set_fifo:
 * configure the FIFO before using it. If nread is -1 RX FIFO will not be
 * configured. same for nwrite
 */
static void npcm_i2c_set_fifo(struct npcm_i2c *bus, int nread, int nwrite)
{
	u8 rxf_ctl = 0;

	if (!bus->fifo_use)
		return;
	npcm_i2c_select_bank(bus, I2C_BANK_1);
	npcm_i2c_clear_tx_fifo(bus);
	npcm_i2c_clear_rx_fifo(bus);

	/* configure RX FIFO */
	if (nread > 0) {
		rxf_ctl = min_t(int, nread, bus->data->fifo_size);

		/* set LAST bit. if LAST is set next FIFO packet is nacked */
		if (nread <= bus->data->fifo_size)
			rxf_ctl |= bus->data->rxf_ctl_last_pec;

		/*
		 * if we are about to read the first byte in blk rd mode,
		 * don't NACK it. If slave returns zero size HW can't NACK
		 * it immediately, it will read extra byte and then NACK.
		 */
		if (bus->rd_ind == 0 && bus->read_block_use) {
			/* set fifo to read one byte, no last: */
			rxf_ctl = 1;
		}

		/* set fifo size: */
		iowrite8(rxf_ctl, bus->reg + NPCM_I2CRXF_CTL);
	}

	/* configure TX FIFO */
	if (nwrite > 0) {
		if (nwrite > bus->data->fifo_size)
			/* data to send is more then FIFO size. */
			iowrite8(bus->data->fifo_size, bus->reg + NPCM_I2CTXF_CTL);
		else
			iowrite8(nwrite, bus->reg + NPCM_I2CTXF_CTL);

		npcm_i2c_clear_tx_fifo(bus);
	}
}

static void npcm_i2c_read_fifo(struct npcm_i2c *bus, u8 bytes_in_fifo)
{
	u8 data;

	while (bytes_in_fifo--) {
		data = npcm_i2c_rd_byte(bus);
		if (bus->rd_ind < bus->rd_size)
			bus->rd_buf[bus->rd_ind++] = data;
	}
}

static void npcm_i2c_master_abort(struct npcm_i2c *bus)
{
	/* Only current master is allowed to issue a stop condition */
	if (!npcm_i2c_is_master(bus))
		return;

	npcm_i2c_eob_int(bus, true);
	npcm_i2c_master_stop(bus);
	npcm_i2c_clear_master_status(bus);
}

#if IS_ENABLED(CONFIG_I2C_SLAVE)
static u8 npcm_i2c_get_slave_addr(struct npcm_i2c *bus, enum i2c_addr addr_type)
{
	u8 slave_add;

	if (addr_type > I2C_SLAVE_ADDR2 && addr_type <= I2C_SLAVE_ADDR10)
		dev_err(bus->dev, "get slave: try to use more than 2 SA not supported\n");

	slave_add = ioread8(bus->reg + npcm_i2caddr[(int)addr_type]);

	return slave_add;
}

static int npcm_i2c_remove_slave_addr(struct npcm_i2c *bus, u8 slave_add)
{
	int i;

	/* Set the enable bit */
	slave_add |= 0x80;

	for (i = I2C_SLAVE_ADDR1; i < I2C_NUM_OWN_ADDR_SUPPORTED; i++) {
		if (ioread8(bus->reg + npcm_i2caddr[i]) == slave_add)
			iowrite8(0, bus->reg + npcm_i2caddr[i]);
	}

	return 0;
}

static void npcm_i2c_write_fifo_slave(struct npcm_i2c *bus, u16 max_bytes)
{
	/*
	 * Fill the FIFO, while the FIFO is not full and there are more bytes
	 * to write
	 */
	npcm_i2c_clear_fifo_int(bus);
	npcm_i2c_clear_tx_fifo(bus);
	iowrite8(0, bus->reg + NPCM_I2CTXF_CTL);
	while (max_bytes-- && bus->data->fifo_size != npcm_i2c_fifo_usage(bus)) {
		if (bus->slv_wr_size <= 0)
			break;
		bus->slv_wr_ind = bus->slv_wr_ind & (bus->data->fifo_size - 1);
		npcm_i2c_wr_byte(bus, bus->slv_wr_buf[bus->slv_wr_ind]);
		bus->slv_wr_ind++;
		bus->slv_wr_ind = bus->slv_wr_ind & (bus->data->fifo_size - 1);
		bus->slv_wr_size--;
	}
}

static void npcm_i2c_read_fifo_slave(struct npcm_i2c *bus, u8 bytes_in_fifo)
{
	u8 data;

	if (!bus->slave)
		return;

	while (bytes_in_fifo--) {
		data = npcm_i2c_rd_byte(bus);

		bus->slv_rd_ind = bus->slv_rd_ind & (bus->data->fifo_size - 1);
		bus->slv_rd_buf[bus->slv_rd_ind] = data;
		bus->slv_rd_ind++;

		/* 1st byte is length in block protocol: */
		if (bus->slv_rd_ind == 1 && bus->read_block_use)
			bus->slv_rd_size = data + bus->PEC_use + 1;
	}
}

static int npcm_i2c_slave_get_wr_buf(struct npcm_i2c *bus)
{
	int i;
	u8 value;
	int ind;
	int ret = bus->slv_wr_ind;

	/* fill a cyclic buffer */
	for (i = 0; i < bus->data->fifo_size; i++) {
		if (bus->slv_wr_size >= bus->data->fifo_size)
			break;
		if (bus->state == I2C_SLAVE_MATCH) {
			i2c_slave_event(bus->slave, I2C_SLAVE_READ_REQUESTED, &value);
			bus->state = I2C_OPER_STARTED;
		} else {
			i2c_slave_event(bus->slave, I2C_SLAVE_READ_PROCESSED, &value);
		}
		ind = (bus->slv_wr_ind + bus->slv_wr_size) & (bus->data->fifo_size - 1);
		bus->slv_wr_buf[ind] = value;
		bus->slv_wr_size++;
	}
	return bus->data->fifo_size - ret;
}

static void npcm_i2c_slave_send_rd_buf(struct npcm_i2c *bus)
{
	int i;

	for (i = 0; i < bus->slv_rd_ind; i++)
		i2c_slave_event(bus->slave, I2C_SLAVE_WRITE_RECEIVED,
				&bus->slv_rd_buf[i]);
	/*
	 * once we send bytes up, need to reset the counter of the wr buf
	 * got data from master (new offset in device), ignore wr fifo:
	 */
	if (bus->slv_rd_ind) {
		bus->slv_wr_size = 0;
		bus->slv_wr_ind = 0;
	}

	bus->slv_rd_ind = 0;
	bus->slv_rd_size = bus->adap.quirks->max_read_len;

	npcm_i2c_clear_fifo_int(bus);
	npcm_i2c_clear_rx_fifo(bus);
}

static void npcm_i2c_slave_receive(struct npcm_i2c *bus, u16 nread,
				   u8 *read_data)
{
	bus->state = I2C_OPER_STARTED;
	bus->operation = I2C_READ_OPER;
	bus->slv_rd_size = nread;
	bus->slv_rd_ind = 0;

	iowrite8(0, bus->reg + NPCM_I2CTXF_CTL);
	iowrite8(bus->data->fifo_size, bus->reg + NPCM_I2CRXF_CTL);
	npcm_i2c_clear_tx_fifo(bus);
	npcm_i2c_clear_rx_fifo(bus);
}

static void npcm_i2c_slave_xmit(struct npcm_i2c *bus, u16 nwrite,
				u8 *write_data)
{
	if (nwrite == 0)
		return;

	bus->operation = I2C_WRITE_OPER;

	/* get the next buffer */
	npcm_i2c_slave_get_wr_buf(bus);
	npcm_i2c_write_fifo_slave(bus, nwrite);
}

/*
 * npcm_i2c_slave_wr_buf_sync:
 * currently slave IF only supports single byte operations.
 * in order to utilize the npcm HW FIFO, the driver will ask for 16 bytes
 * at a time, pack them in buffer, and then transmit them all together
 * to the FIFO and onward to the bus.
 * NACK on read will be once reached to bus->adap->quirks->max_read_len.
 * sending a NACK wherever the backend requests for it is not supported.
 * the next two functions allow reading to local buffer before writing it all
 * to the HW FIFO.
 */
static void npcm_i2c_slave_wr_buf_sync(struct npcm_i2c *bus)
{
	int left_in_fifo;

	left_in_fifo = bus->data->txf_sts_tx_bytes &
			ioread8(bus->reg + NPCM_I2CTXF_STS);

	/* fifo already full: */
	if (left_in_fifo >= bus->data->fifo_size ||
	    bus->slv_wr_size >= bus->data->fifo_size)
		return;

	/* update the wr fifo index back to the untransmitted bytes: */
	bus->slv_wr_ind = bus->slv_wr_ind - left_in_fifo;
	bus->slv_wr_size = bus->slv_wr_size + left_in_fifo;

	if (bus->slv_wr_ind < 0)
		bus->slv_wr_ind += bus->data->fifo_size;
}

static void npcm_i2c_slave_rd_wr(struct npcm_i2c *bus)
{
	if (NPCM_I2CST_XMIT & ioread8(bus->reg + NPCM_I2CST)) {
		/*
		 * Slave got an address match with direction bit 1 so it should
		 * transmit data. Write till the master will NACK
		 */
		bus->operation = I2C_WRITE_OPER;
		npcm_i2c_slave_xmit(bus, bus->adap.quirks->max_write_len,
				    bus->slv_wr_buf);
	} else {
		/*
		 * Slave got an address match with direction bit 0 so it should
		 * receive data.
		 * this module does not support saying no to bytes.
		 * it will always ACK.
		 */
		bus->operation = I2C_READ_OPER;
		npcm_i2c_read_fifo_slave(bus, npcm_i2c_fifo_usage(bus));
		bus->stop_ind = I2C_SLAVE_RCV_IND;
		npcm_i2c_slave_send_rd_buf(bus);
		npcm_i2c_slave_receive(bus, bus->adap.quirks->max_read_len,
				       bus->slv_rd_buf);
	}
}

static irqreturn_t npcm_i2c_int_slave_handler(struct npcm_i2c *bus)
{
	u8 val;
	irqreturn_t ret = IRQ_NONE;
	u8 i2cst = ioread8(bus->reg + NPCM_I2CST);

	/* Slave: A NACK has occurred */
	if (NPCM_I2CST_NEGACK & i2cst) {
		bus->stop_ind = I2C_NACK_IND;
		npcm_i2c_slave_wr_buf_sync(bus);
		if (bus->fifo_use)
			/* clear the FIFO */
			iowrite8(NPCM_I2CFIF_CTS_CLR_FIFO,
				 bus->reg + NPCM_I2CFIF_CTS);

		/* In slave write, NACK is OK, otherwise it is a problem */
		bus->stop_ind = I2C_NO_STATUS_IND;
		bus->operation = I2C_NO_OPER;
		bus->own_slave_addr = 0xFF;

		/*
		 * Slave has to wait for STOP to decide this is the end
		 * of the transaction. tx is not yet considered as done
		 */
		iowrite8(NPCM_I2CST_NEGACK, bus->reg + NPCM_I2CST);

		ret = IRQ_HANDLED;
	}

	/* Slave mode: a Bus Error (BER) has been identified */
	if (NPCM_I2CST_BER & i2cst) {
		/*
		 * Check whether bus arbitration or Start or Stop during data
		 * xfer bus arbitration problem should not result in recovery
		 */
		bus->stop_ind = I2C_BUS_ERR_IND;

		/* wait for bus busy before clear fifo */
		iowrite8(NPCM_I2CFIF_CTS_CLR_FIFO, bus->reg + NPCM_I2CFIF_CTS);

		bus->state = I2C_IDLE;

		/*
		 * in BER case we might get 2 interrupts: one for slave one for
		 * master ( for a channel which is master\slave switching)
		 */
		if (completion_done(&bus->cmd_complete) == false) {
			bus->cmd_err = -EIO;
			complete(&bus->cmd_complete);
		}
		bus->own_slave_addr = 0xFF;
		iowrite8(NPCM_I2CST_BER, bus->reg + NPCM_I2CST);
		ret = IRQ_HANDLED;
	}

	/* A Slave Stop Condition has been identified */
	if (NPCM_I2CST_SLVSTP & i2cst) {
		u8 bytes_in_fifo = npcm_i2c_fifo_usage(bus);

		bus->stop_ind = I2C_SLAVE_DONE_IND;

		if (bus->operation == I2C_READ_OPER)
			npcm_i2c_read_fifo_slave(bus, bytes_in_fifo);

		/* if the buffer is empty nothing will be sent */
		npcm_i2c_slave_send_rd_buf(bus);

		/* Slave done transmitting or receiving */
		bus->stop_ind = I2C_NO_STATUS_IND;

		/*
		 * Note, just because we got here, it doesn't mean we through
		 * away the wr buffer.
		 * we keep it until the next received offset.
		 */
		bus->operation = I2C_NO_OPER;
		bus->own_slave_addr = 0xFF;
		i2c_slave_event(bus->slave, I2C_SLAVE_STOP, 0);
		iowrite8(NPCM_I2CST_SLVSTP, bus->reg + NPCM_I2CST);
		if (bus->fifo_use) {
			npcm_i2c_clear_fifo_int(bus);
			npcm_i2c_clear_rx_fifo(bus);
			npcm_i2c_clear_tx_fifo(bus);

			iowrite8(NPCM_I2CFIF_CTS_CLR_FIFO,
				 bus->reg + NPCM_I2CFIF_CTS);
		}
		bus->state = I2C_IDLE;
		ret = IRQ_HANDLED;
	}

	/* restart condition occurred and Rx-FIFO was not empty */
	if (bus->fifo_use && FIELD_GET(NPCM_I2CFIF_CTS_SLVRSTR,
				       ioread8(bus->reg + NPCM_I2CFIF_CTS))) {
		bus->stop_ind = I2C_SLAVE_RESTART_IND;
		bus->master_or_slave = I2C_SLAVE;
		if (bus->operation == I2C_READ_OPER)
			npcm_i2c_read_fifo_slave(bus, npcm_i2c_fifo_usage(bus));
		bus->operation = I2C_WRITE_OPER;
		iowrite8(0, bus->reg + NPCM_I2CRXF_CTL);
		val = NPCM_I2CFIF_CTS_CLR_FIFO | NPCM_I2CFIF_CTS_SLVRSTR |
		      NPCM_I2CFIF_CTS_RXF_TXE;
		iowrite8(val, bus->reg + NPCM_I2CFIF_CTS);
		npcm_i2c_slave_rd_wr(bus);
		ret = IRQ_HANDLED;
	}

	/* A Slave Address Match has been identified */
	if (NPCM_I2CST_NMATCH & i2cst) {
		u8 info = 0;

		/* Address match automatically implies slave mode */
		bus->master_or_slave = I2C_SLAVE;
		npcm_i2c_clear_fifo_int(bus);
		npcm_i2c_clear_rx_fifo(bus);
		npcm_i2c_clear_tx_fifo(bus);
		iowrite8(0, bus->reg + NPCM_I2CTXF_CTL);
		iowrite8(bus->data->fifo_size, bus->reg + NPCM_I2CRXF_CTL);
		if (NPCM_I2CST_XMIT & i2cst) {
			bus->operation = I2C_WRITE_OPER;
		} else {
			i2c_slave_event(bus->slave, I2C_SLAVE_WRITE_REQUESTED,
					&info);
			bus->operation = I2C_READ_OPER;
		}
		if (bus->own_slave_addr == 0xFF) {
			/* Check which type of address match */
			val = ioread8(bus->reg + NPCM_I2CCST);
			if (NPCM_I2CCST_MATCH & val) {
				u16 addr;
				enum i2c_addr eaddr;
				u8 i2ccst2;
				u8 i2ccst3;

				i2ccst3 = ioread8(bus->reg + NPCM_I2CCST3);
				i2ccst2 = ioread8(bus->reg + NPCM_I2CCST2);

				/*
				 * the i2c module can response to 10 own SA.
				 * check which one was addressed by the master.
				 * respond to the first one.
				 */
				addr = ((i2ccst3 & 0x07) << 7) |
					(i2ccst2 & 0x7F);
				info = ffs(addr);
				eaddr = (enum i2c_addr)info;
				addr = npcm_i2c_get_slave_addr(bus, eaddr);
				addr &= 0x7F;
				bus->own_slave_addr = addr;
				if (bus->PEC_mask & BIT(info))
					bus->PEC_use = true;
				else
					bus->PEC_use = false;
			} else {
				if (NPCM_I2CCST_GCMATCH & val)
					bus->own_slave_addr = 0;
				if (NPCM_I2CCST_ARPMATCH & val)
					bus->own_slave_addr = 0x61;
			}
		} else {
			/*
			 *  Slave match can happen in two options:
			 *  1. Start, SA, read (slave read without further ado)
			 *  2. Start, SA, read, data, restart, SA, read,  ...
			 *     (slave read in fragmented mode)
			 *  3. Start, SA, write, data, restart, SA, read, ..
			 *     (regular write-read mode)
			 */
			if ((bus->state == I2C_OPER_STARTED &&
			     bus->operation == I2C_READ_OPER &&
			     bus->stop_ind == I2C_SLAVE_XMIT_IND) ||
			     bus->stop_ind == I2C_SLAVE_RCV_IND) {
				/* slave tx after slave rx w/o STOP */
				bus->stop_ind = I2C_SLAVE_RESTART_IND;
			}
		}

		if (NPCM_I2CST_XMIT & i2cst)
			bus->stop_ind = I2C_SLAVE_XMIT_IND;
		else
			bus->stop_ind = I2C_SLAVE_RCV_IND;
		bus->state = I2C_SLAVE_MATCH;
		npcm_i2c_slave_rd_wr(bus);
		iowrite8(NPCM_I2CST_NMATCH, bus->reg + NPCM_I2CST);
		ret = IRQ_HANDLED;
	}

	/* Slave SDA status is set - tx or rx */
	if ((NPCM_I2CST_SDAST & i2cst) ||
	    (bus->fifo_use &&
	    (npcm_i2c_tx_fifo_empty(bus) || npcm_i2c_rx_fifo_full(bus)))) {
		npcm_i2c_slave_rd_wr(bus);
		iowrite8(NPCM_I2CST_SDAST, bus->reg + NPCM_I2CST);
		ret = IRQ_HANDLED;
	} /* SDAST */

	/*
	 * If irq is not one of the above, make sure EOB is disabled and all
	 * status bits are cleared.
	 */
	if (ret == IRQ_NONE) {
		npcm_i2c_eob_int(bus, false);
		npcm_i2c_clear_master_status(bus);
	}

	return IRQ_HANDLED;
}

static int npcm_i2c_reg_slave(struct i2c_client *client)
{
	unsigned long lock_flags;
	struct npcm_i2c *bus = i2c_get_adapdata(client->adapter);

	bus->slave = client;

	if (!bus->slave)
		return -EINVAL;

	if (client->flags & I2C_CLIENT_TEN)
		return -EAFNOSUPPORT;

	spin_lock_irqsave(&bus->lock, lock_flags);

	npcm_i2c_init_params(bus);
	bus->slv_rd_size = 0;
	bus->slv_wr_size = 0;
	bus->slv_rd_ind = 0;
	bus->slv_wr_ind = 0;
	if (client->flags & I2C_CLIENT_PEC)
		bus->PEC_use = true;

	dev_info(bus->dev, "i2c%d register slave SA=0x%x, PEC=%d\n", bus->num,
		 client->addr, bus->PEC_use);

	npcm_i2c_slave_enable(bus, I2C_SLAVE_ADDR1, client->addr, true);
	npcm_i2c_clear_fifo_int(bus);
	npcm_i2c_clear_rx_fifo(bus);
	npcm_i2c_clear_tx_fifo(bus);
	npcm_i2c_slave_int_enable(bus, true);

	spin_unlock_irqrestore(&bus->lock, lock_flags);
	return 0;
}

static int npcm_i2c_unreg_slave(struct i2c_client *client)
{
	struct npcm_i2c *bus = client->adapter->algo_data;
	unsigned long lock_flags;

	spin_lock_irqsave(&bus->lock, lock_flags);
	if (!bus->slave) {
		spin_unlock_irqrestore(&bus->lock, lock_flags);
		return -EINVAL;
	}
	npcm_i2c_slave_int_enable(bus, false);
	npcm_i2c_remove_slave_addr(bus, client->addr);
	bus->slave = NULL;
	spin_unlock_irqrestore(&bus->lock, lock_flags);
	return 0;
}
#endif /* CONFIG_I2C_SLAVE */

static void npcm_i2c_master_fifo_read(struct npcm_i2c *bus)
{
	int rcount;
	int fifo_bytes;
	enum i2c_state_ind ind = I2C_MASTER_DONE_IND;

	fifo_bytes = npcm_i2c_fifo_usage(bus);
	rcount = bus->rd_size - bus->rd_ind;

	/*
	 * In order not to change the RX_TRH during transaction (we found that
	 * this might be problematic if it takes too much time to read the FIFO)
	 * we read the data in the following way. If the number of bytes to
	 * read == FIFO Size + C (where C < FIFO Size)then first read C bytes
	 * and in the next int we read rest of the data.
	 */
	if (rcount < (2 * bus->data->fifo_size) && rcount > bus->data->fifo_size)
		fifo_bytes = rcount - bus->data->fifo_size;

	if (rcount <= fifo_bytes) {
		/* last bytes are about to be read - end of tx */
		bus->state = I2C_STOP_PENDING;
		bus->stop_ind = ind;
		npcm_i2c_eob_int(bus, true);
		/* Stop should be set before reading last byte. */
		npcm_i2c_master_stop(bus);
		npcm_i2c_read_fifo(bus, fifo_bytes);
	} else {
		npcm_i2c_read_fifo(bus, fifo_bytes);
		rcount = bus->rd_size - bus->rd_ind;
		npcm_i2c_set_fifo(bus, rcount, -1);
	}
}

static void npcm_i2c_irq_master_handler_write(struct npcm_i2c *bus)
{
	u16 wcount;

	if (bus->fifo_use)
		npcm_i2c_clear_tx_fifo(bus); /* clear the TX fifo status bit */

	/* Master write operation - last byte handling */
	if (bus->wr_ind == bus->wr_size) {
		if (bus->fifo_use && npcm_i2c_fifo_usage(bus) > 0)
			/*
			 * No more bytes to send (to add to the FIFO),
			 * however the FIFO is not empty yet. It is
			 * still in the middle of tx. Currently there's nothing
			 * to do except for waiting to the end of the tx
			 * We will get an int when the FIFO will get empty.
			 */
			return;

		if (bus->rd_size == 0) {
			/* all bytes have been written, in wr only operation */
			npcm_i2c_eob_int(bus, true);
			bus->state = I2C_STOP_PENDING;
			bus->stop_ind = I2C_MASTER_DONE_IND;
			npcm_i2c_master_stop(bus);
			/* Clear SDA Status bit (by writing dummy byte) */
			npcm_i2c_wr_byte(bus, 0xFF);

		} else {
			/* last write-byte written on previous int - restart */
			npcm_i2c_set_fifo(bus, bus->rd_size, -1);
			/* Generate repeated start upon next write to SDA */
			npcm_i2c_master_start(bus);

			/*
			 * Receiving one byte only - stall after successful
			 * completion of send address byte. If we NACK here, and
			 * slave doesn't ACK the address, we might
			 * unintentionally NACK the next multi-byte read.
			 */
			if (bus->rd_size == 1)
				npcm_i2c_stall_after_start(bus, true);

			/* Next int will occur on read */
			bus->operation = I2C_READ_OPER;
			/* send the slave address in read direction */
			npcm_i2c_wr_byte(bus, bus->dest_addr | 0x1);
		}
	} else {
		/* write next byte not last byte and not slave address */
		if (!bus->fifo_use || bus->wr_size == 1) {
			npcm_i2c_wr_byte(bus, bus->wr_buf[bus->wr_ind++]);
		} else {
			wcount = bus->wr_size - bus->wr_ind;
			npcm_i2c_set_fifo(bus, -1, wcount);
			if (wcount)
				npcm_i2c_write_to_fifo_master(bus, wcount);
		}
	}
}

static void npcm_i2c_irq_master_handler_read(struct npcm_i2c *bus)
{
	u16 block_extra_bytes_size;
	u8 data;

	/* added bytes to the packet: */
	block_extra_bytes_size = bus->read_block_use + bus->PEC_use;

	/*
	 * Perform master read, distinguishing between last byte and the rest of
	 * the bytes. The last byte should be read when the clock is stopped
	 */
	if (bus->rd_ind == 0) { /* first byte handling: */
		if (bus->read_block_use) {
			/* first byte in block protocol is the size: */
			data = npcm_i2c_rd_byte(bus);
			data = clamp_val(data, 1, I2C_SMBUS_BLOCK_MAX);
			bus->rd_size = data + block_extra_bytes_size;
			bus->rd_buf[bus->rd_ind++] = data;

			/* clear RX FIFO interrupt status: */
			if (bus->fifo_use) {
				data = ioread8(bus->reg + NPCM_I2CFIF_CTS);
				data = data | NPCM_I2CFIF_CTS_RXF_TXE;
				iowrite8(data, bus->reg + NPCM_I2CFIF_CTS);
			}

			npcm_i2c_set_fifo(bus, bus->rd_size - 1, -1);
			npcm_i2c_stall_after_start(bus, false);
		} else {
			npcm_i2c_clear_tx_fifo(bus);
			npcm_i2c_master_fifo_read(bus);
		}
	} else {
		if (bus->rd_size == block_extra_bytes_size &&
		    bus->read_block_use) {
			bus->state = I2C_STOP_PENDING;
			bus->stop_ind = I2C_BLOCK_BYTES_ERR_IND;
			bus->cmd_err = -EIO;
			npcm_i2c_eob_int(bus, true);
			npcm_i2c_master_stop(bus);
			npcm_i2c_read_fifo(bus, npcm_i2c_fifo_usage(bus));
		} else {
			npcm_i2c_master_fifo_read(bus);
		}
	}
}

static void npcm_i2c_irq_handle_nmatch(struct npcm_i2c *bus)
{
	iowrite8(NPCM_I2CST_NMATCH, bus->reg + NPCM_I2CST);
	npcm_i2c_nack(bus);
	bus->stop_ind = I2C_BUS_ERR_IND;
	npcm_i2c_callback(bus, bus->stop_ind, npcm_i2c_get_index(bus));
}

/* A NACK has occurred */
static void npcm_i2c_irq_handle_nack(struct npcm_i2c *bus)
{
	u8 val;

	if (bus->nack_cnt < ULLONG_MAX)
		bus->nack_cnt++;

	if (bus->fifo_use) {
		/*
		 * if there are still untransmitted bytes in TX FIFO
		 * reduce them from wr_ind
		 */
		if (bus->operation == I2C_WRITE_OPER)
			bus->wr_ind -= npcm_i2c_fifo_usage(bus);

		/* clear the FIFO */
		iowrite8(NPCM_I2CFIF_CTS_CLR_FIFO, bus->reg + NPCM_I2CFIF_CTS);
	}

	/* In master write operation, got unexpected NACK */
	bus->stop_ind = I2C_NACK_IND;
	/* Only current master is allowed to issue Stop Condition */
	if (npcm_i2c_is_master(bus)) {
		/* stopping in the middle */
		npcm_i2c_eob_int(bus, false);
		npcm_i2c_master_stop(bus);

		/* Clear SDA Status bit (by reading dummy byte) */
		npcm_i2c_rd_byte(bus);

		/*
		 * The bus is released from stall only after the SW clears
		 * NEGACK bit. Then a Stop condition is sent.
		 */
		npcm_i2c_clear_master_status(bus);
		readx_poll_timeout_atomic(ioread8, bus->reg + NPCM_I2CCST, val,
					  !(val & NPCM_I2CCST_BUSY), 10, 200);
		/* Verify no status bits are still set after bus is released */
		npcm_i2c_clear_master_status(bus);
	}
	bus->state = I2C_IDLE;

	/*
	 * In Master mode, NACK should be cleared only after STOP.
	 * In such case, the bus is released from stall only after the
	 * software clears NACK bit. Then a Stop condition is sent.
	 */
	npcm_i2c_callback(bus, bus->stop_ind, bus->wr_ind);
}

	/* Master mode: a Bus Error has been identified */
static void npcm_i2c_irq_handle_ber(struct npcm_i2c *bus)
{
	if (bus->ber_cnt < ULLONG_MAX)
		bus->ber_cnt++;
	bus->stop_ind = I2C_BUS_ERR_IND;
	if (npcm_i2c_is_master(bus)) {
		npcm_i2c_master_abort(bus);
	} else {
		npcm_i2c_clear_master_status(bus);

		/* Clear BB (BUS BUSY) bit */
		iowrite8(NPCM_I2CCST_BB, bus->reg + NPCM_I2CCST);

		bus->cmd_err = -EAGAIN;
		npcm_i2c_callback(bus, bus->stop_ind, npcm_i2c_get_index(bus));
	}
	bus->state = I2C_IDLE;
}

	/* EOB: a master End Of Busy (meaning STOP completed) */
static void npcm_i2c_irq_handle_eob(struct npcm_i2c *bus)
{
	npcm_i2c_eob_int(bus, false);
	bus->state = I2C_IDLE;
	npcm_i2c_callback(bus, bus->stop_ind, bus->rd_ind);
}

/* Address sent and requested stall occurred (Master mode) */
static void npcm_i2c_irq_handle_stall_after_start(struct npcm_i2c *bus)
{
	if (npcm_i2c_is_quick(bus)) {
		bus->state = I2C_STOP_PENDING;
		bus->stop_ind = I2C_MASTER_DONE_IND;
		npcm_i2c_eob_int(bus, true);
		npcm_i2c_master_stop(bus);
	} else if ((bus->rd_size == 1) && !bus->read_block_use) {
		/*
		 * Receiving one byte only - set NACK after ensuring
		 * slave ACKed the address byte.
		 */
		npcm_i2c_nack(bus);
	}

	/* Reset stall-after-address-byte */
	npcm_i2c_stall_after_start(bus, false);

	/* Clear stall only after setting STOP */
	iowrite8(NPCM_I2CST_STASTR, bus->reg + NPCM_I2CST);
}

/* SDA status is set - TX or RX, master */
static void npcm_i2c_irq_handle_sda(struct npcm_i2c *bus, u8 i2cst)
{
	u8 fif_cts;

	if (!npcm_i2c_is_master(bus))
		return;

	if (bus->state == I2C_IDLE) {
		bus->stop_ind = I2C_WAKE_UP_IND;

		if (npcm_i2c_is_quick(bus) || bus->read_block_use)
			/*
			 * Need to stall after successful
			 * completion of sending address byte
			 */
			npcm_i2c_stall_after_start(bus, true);
		else
			npcm_i2c_stall_after_start(bus, false);

		/*
		 * Receiving one byte only - stall after successful completion
		 * of sending address byte If we NACK here, and slave doesn't
		 * ACK the address, we might unintentionally NACK the next
		 * multi-byte read
		 */
		if (bus->wr_size == 0 && bus->rd_size == 1)
			npcm_i2c_stall_after_start(bus, true);

		/* Initiate I2C master tx */

		/* select bank 1 for FIFO regs */
		npcm_i2c_select_bank(bus, I2C_BANK_1);

		fif_cts = ioread8(bus->reg + NPCM_I2CFIF_CTS);
		fif_cts = fif_cts & ~NPCM_I2CFIF_CTS_SLVRSTR;

		/* clear FIFO and relevant status bits. */
		fif_cts = fif_cts | NPCM_I2CFIF_CTS_CLR_FIFO;
		iowrite8(fif_cts, bus->reg + NPCM_I2CFIF_CTS);

		/* re-enable */
		fif_cts = fif_cts | NPCM_I2CFIF_CTS_RXF_TXE;
		iowrite8(fif_cts, bus->reg + NPCM_I2CFIF_CTS);

		/*
		 * Configure the FIFO threshold:
		 * according to the needed # of bytes to read.
		 * Note: due to HW limitation can't config the rx fifo before it
		 * got and ACK on the restart. LAST bit will not be reset unless
		 * RX completed. It will stay set on the next tx.
		 */
		if (bus->wr_size)
			npcm_i2c_set_fifo(bus, -1, bus->wr_size);
		else
			npcm_i2c_set_fifo(bus, bus->rd_size, -1);

		bus->state = I2C_OPER_STARTED;

		if (npcm_i2c_is_quick(bus) || bus->wr_size)
			npcm_i2c_wr_byte(bus, bus->dest_addr);
		else
			npcm_i2c_wr_byte(bus, bus->dest_addr | BIT(0));
	/* SDA interrupt, after start\restart */
	} else {
		if (NPCM_I2CST_XMIT & i2cst) {
			bus->operation = I2C_WRITE_OPER;
			npcm_i2c_irq_master_handler_write(bus);
		} else {
			bus->operation = I2C_READ_OPER;
			npcm_i2c_irq_master_handler_read(bus);
		}
	}
}

static int npcm_i2c_int_master_handler(struct npcm_i2c *bus)
{
	u8 i2cst;
	int ret = -EIO;

	i2cst = ioread8(bus->reg + NPCM_I2CST);

	if (FIELD_GET(NPCM_I2CST_NMATCH, i2cst)) {
		npcm_i2c_irq_handle_nmatch(bus);
		return 0;
	}
	/* A NACK has occurred */
	if (FIELD_GET(NPCM_I2CST_NEGACK, i2cst)) {
		npcm_i2c_irq_handle_nack(bus);
		return 0;
	}

	/* Master mode: a Bus Error has been identified */
	if (FIELD_GET(NPCM_I2CST_BER, i2cst)) {
		npcm_i2c_irq_handle_ber(bus);
		return 0;
	}

	/* EOB: a master End Of Busy (meaning STOP completed) */
	if ((FIELD_GET(NPCM_I2CCTL1_EOBINTE,
		       ioread8(bus->reg + NPCM_I2CCTL1)) == 1) &&
	    (FIELD_GET(NPCM_I2CCST3_EO_BUSY,
		       ioread8(bus->reg + NPCM_I2CCST3)))) {
		npcm_i2c_irq_handle_eob(bus);
		return 0;
	}

	/* Address sent and requested stall occurred (Master mode) */
	if (FIELD_GET(NPCM_I2CST_STASTR, i2cst)) {
		npcm_i2c_irq_handle_stall_after_start(bus);
		ret = 0;
	}

	/* SDA status is set - TX or RX, master */
	if (FIELD_GET(NPCM_I2CST_SDAST, i2cst) ||
	    (bus->fifo_use &&
	    (npcm_i2c_tx_fifo_empty(bus) || npcm_i2c_rx_fifo_full(bus)))) {
		npcm_i2c_irq_handle_sda(bus, i2cst);
		ret = 0;
	}

	return ret;
}

/* recovery using TGCLK functionality of the module */
static int npcm_i2c_recovery_tgclk(struct i2c_adapter *_adap)
{
	u8               val;
	u8               fif_cts;
	bool             done = false;
	int              status = -ENOTRECOVERABLE;
	struct npcm_i2c *bus = container_of(_adap, struct npcm_i2c, adap);
	/* Allow 3 bytes (27 toggles) to be read from the slave: */
	int              iter = 27;

	if ((npcm_i2c_get_SDA(_adap) == 1) && (npcm_i2c_get_SCL(_adap) == 1)) {
		dev_dbg(bus->dev, "bus%d-0x%x recovery skipped, bus not stuck",
			bus->num, bus->dest_addr);
		npcm_i2c_reset(bus);
		return 0;
	}

	npcm_i2c_int_enable(bus, false);
	npcm_i2c_disable(bus);
	npcm_i2c_enable(bus);
	iowrite8(NPCM_I2CCST_BB, bus->reg + NPCM_I2CCST);
	npcm_i2c_clear_tx_fifo(bus);
	npcm_i2c_clear_rx_fifo(bus);
	iowrite8(0, bus->reg + NPCM_I2CRXF_CTL);
	iowrite8(0, bus->reg + NPCM_I2CTXF_CTL);
	npcm_i2c_stall_after_start(bus, false);

	/* select bank 1 for FIFO regs */
	npcm_i2c_select_bank(bus, I2C_BANK_1);

	/* clear FIFO and relevant status bits. */
	fif_cts = ioread8(bus->reg + NPCM_I2CFIF_CTS);
	fif_cts &= ~NPCM_I2CFIF_CTS_SLVRSTR;
	fif_cts |= NPCM_I2CFIF_CTS_CLR_FIFO;
	iowrite8(fif_cts, bus->reg + NPCM_I2CFIF_CTS);
	npcm_i2c_set_fifo(bus, -1, 0);

	/* Repeat the following sequence until SDA is released */
	do {
		/* Issue a single SCL toggle */
		iowrite8(NPCM_I2CCST_TGSCL, bus->reg + NPCM_I2CCST);
		usleep_range(20, 30);
		/* If SDA line is inactive (high), stop */
		if (npcm_i2c_get_SDA(_adap)) {
			done = true;
			status = 0;
		}
	} while (!done && iter--);

	/* If SDA line is released: send start-addr-stop, to re-sync. */
	if (npcm_i2c_get_SDA(_adap)) {
		/* Send an address byte in write direction: */
		npcm_i2c_wr_byte(bus, bus->dest_addr);
		npcm_i2c_master_start(bus);
		/* Wait until START condition is sent */
		status = readx_poll_timeout(npcm_i2c_get_SCL, _adap, val, !val,
					    20, 200);
		/* If START condition was sent */
		if (npcm_i2c_is_master(bus) > 0) {
			usleep_range(20, 30);
			npcm_i2c_master_stop(bus);
			usleep_range(200, 500);
		}
	}
	npcm_i2c_reset(bus);
	npcm_i2c_int_enable(bus, true);

	if ((npcm_i2c_get_SDA(_adap) == 1) && (npcm_i2c_get_SCL(_adap) == 1))
		status = 0;
	else
		status = -ENOTRECOVERABLE;
	if (status) {
		if (bus->rec_fail_cnt < ULLONG_MAX)
			bus->rec_fail_cnt++;
	} else {
		if (bus->rec_succ_cnt < ULLONG_MAX)
			bus->rec_succ_cnt++;
	}
	return status;
}

/* recovery using bit banging functionality of the module */
static void npcm_i2c_recovery_init(struct i2c_adapter *_adap)
{
	struct npcm_i2c *bus = container_of(_adap, struct npcm_i2c, adap);
	struct i2c_bus_recovery_info *rinfo = &bus->rinfo;

	rinfo->recover_bus = npcm_i2c_recovery_tgclk;

	/*
	 * npcm i2c HW allows direct reading of SCL and SDA.
	 * However, it does not support setting SCL and SDA directly.
	 * The recovery function can toggle SCL when SDA is low (but not set)
	 * Getter functions used internally, and can be used externally.
	 */
	rinfo->get_scl = npcm_i2c_get_SCL;
	rinfo->get_sda = npcm_i2c_get_SDA;
	_adap->bus_recovery_info = rinfo;
}

/* SCLFRQ min/max field values */
#define SCLFRQ_MIN  10
#define SCLFRQ_MAX  511
#define clk_coef(freq, mul)	DIV_ROUND_UP((freq) * (mul), 1000000)

/*
 * npcm_i2c_init_clk: init HW timing parameters.
 * NPCM7XX i2c module timing parameters are dependent on module core clk (APB)
 * and bus frequency.
 * 100kHz bus requires tSCL = 4 * SCLFRQ * tCLK. LT and HT are symmetric.
 * 400kHz bus requires asymmetric HT and LT. A different equation is recommended
 * by the HW designer, given core clock range (equations in comments below).
 *
 */
static int npcm_i2c_init_clk(struct npcm_i2c *bus, u32 bus_freq_hz)
{
	u32  k1 = 0;
	u32  k2 = 0;
	u8   dbnct = 0;
	u32  sclfrq = 0;
	u8   hldt = 7;
	u8   fast_mode = 0;
	u32  src_clk_khz;
	u32  bus_freq_khz;

	src_clk_khz = bus->apb_clk / 1000;
	bus_freq_khz = bus_freq_hz / 1000;
	bus->bus_freq = bus_freq_hz;

	/* 100KHz and below: */
	if (bus_freq_hz <= I2C_MAX_STANDARD_MODE_FREQ) {
		sclfrq = src_clk_khz / (bus_freq_khz * 4);

		if (sclfrq < SCLFRQ_MIN || sclfrq > SCLFRQ_MAX)
			return -EDOM;

		if (src_clk_khz >= 40000)
			hldt = 17;
		else if (src_clk_khz >= 12500)
			hldt = 15;
		else
			hldt = 7;
	}

	/* 400KHz: */
	else if (bus_freq_hz <= I2C_MAX_FAST_MODE_FREQ) {
		sclfrq = 0;
		fast_mode = I2CCTL3_400K_MODE;

		if (src_clk_khz < 7500)
			/* 400KHZ cannot be supported for core clock < 7.5MHz */
			return -EDOM;

		else if (src_clk_khz >= 50000) {
			k1 = 80;
			k2 = 48;
			hldt = 12;
			dbnct = 7;
		}

		/* Master or Slave with frequency > 25MHz */
		else if (src_clk_khz > 25000) {
			hldt = clk_coef(src_clk_khz, 300) + 7;
			k1 = clk_coef(src_clk_khz, 1600);
			k2 = clk_coef(src_clk_khz, 900);
		}
	}

	/* 1MHz: */
	else if (bus_freq_hz <= I2C_MAX_FAST_MODE_PLUS_FREQ) {
		sclfrq = 0;
		fast_mode = I2CCTL3_400K_MODE;

		/* 1MHZ cannot be supported for core clock < 24 MHz */
		if (src_clk_khz < 24000)
			return -EDOM;

		k1 = clk_coef(src_clk_khz, 620);
		k2 = clk_coef(src_clk_khz, 380);

		/* Core clk > 40 MHz */
		if (src_clk_khz > 40000) {
			/*
			 * Set HLDT:
			 * SDA hold time:  (HLDT-7) * T(CLK) >= 120
			 * HLDT = 120/T(CLK) + 7 = 120 * FREQ(CLK) + 7
			 */
			hldt = clk_coef(src_clk_khz, 120) + 7;
		} else {
			hldt = 7;
			dbnct = 2;
		}
	}

	/* Frequency larger than 1 MHz is not supported */
	else
		return -EINVAL;

	if (bus_freq_hz >= I2C_MAX_FAST_MODE_FREQ) {
		k1 = round_up(k1, 2);
		k2 = round_up(k2 + 1, 2);
		if (k1 < SCLFRQ_MIN || k1 > SCLFRQ_MAX ||
		    k2 < SCLFRQ_MIN || k2 > SCLFRQ_MAX)
			return -EDOM;
	}

	/* write sclfrq value. bits [6:0] are in I2CCTL2 reg */
	iowrite8(FIELD_PREP(I2CCTL2_SCLFRQ6_0, sclfrq & 0x7F),
		 bus->reg + NPCM_I2CCTL2);

	/* bits [8:7] are in I2CCTL3 reg */
	iowrite8(fast_mode | FIELD_PREP(I2CCTL3_SCLFRQ8_7, (sclfrq >> 7) & 0x3),
		 bus->reg + NPCM_I2CCTL3);

	/* Select Bank 0 to access NPCM_I2CCTL4/NPCM_I2CCTL5 */
	npcm_i2c_select_bank(bus, I2C_BANK_0);

	if (bus_freq_hz >= I2C_MAX_FAST_MODE_FREQ) {
		/*
		 * Set SCL Low/High Time:
		 * k1 = 2 * SCLLT7-0 -> Low Time  = k1 / 2
		 * k2 = 2 * SCLLT7-0 -> High Time = k2 / 2
		 */
		iowrite8(k1 / 2, bus->reg + NPCM_I2CSCLLT);
		iowrite8(k2 / 2, bus->reg + NPCM_I2CSCLHT);

		iowrite8(dbnct, bus->reg + NPCM_I2CCTL5);
	}

	iowrite8(hldt, bus->reg + NPCM_I2CCTL4);

	/* Return to Bank 1, and stay there by default: */
	npcm_i2c_select_bank(bus, I2C_BANK_1);

	return 0;
}

static int npcm_i2c_init_module(struct npcm_i2c *bus, enum i2c_mode mode,
				u32 bus_freq_hz)
{
	u8 val;
	int ret;

	/* Check whether module already enabled or frequency is out of bounds */
	if ((bus->state != I2C_DISABLE && bus->state != I2C_IDLE) ||
	    bus_freq_hz < I2C_FREQ_MIN_HZ || bus_freq_hz > I2C_FREQ_MAX_HZ)
		return -EINVAL;

	npcm_i2c_int_enable(bus, false);
	npcm_i2c_disable(bus);

	/* Configure FIFO mode : */
	if (FIELD_GET(I2C_VER_FIFO_EN, ioread8(bus->reg + I2C_VER))) {
		bus->fifo_use = true;
		npcm_i2c_select_bank(bus, I2C_BANK_0);
		val = ioread8(bus->reg + NPCM_I2CFIF_CTL);
		val |= NPCM_I2CFIF_CTL_FIFO_EN;
		iowrite8(val, bus->reg + NPCM_I2CFIF_CTL);
		npcm_i2c_select_bank(bus, I2C_BANK_1);
	} else {
		bus->fifo_use = false;
	}

	/* Configure I2C module clock frequency */
	ret = npcm_i2c_init_clk(bus, bus_freq_hz);
	if (ret) {
		dev_err(bus->dev, "npcm_i2c_init_clk failed\n");
		return ret;
	}

	/* Enable module (before configuring CTL1) */
	npcm_i2c_enable(bus);
	bus->state = I2C_IDLE;
	val = ioread8(bus->reg + NPCM_I2CCTL1);
	val = (val | NPCM_I2CCTL1_NMINTE) & ~NPCM_I2CCTL1_RWS;
	iowrite8(val, bus->reg + NPCM_I2CCTL1);

	npcm_i2c_reset(bus);

	/* Check HW is OK: SDA and SCL should be high at this point. */
	if ((npcm_i2c_get_SDA(&bus->adap) == 0) || (npcm_i2c_get_SCL(&bus->adap) == 0)) {
		dev_err(bus->dev, "I2C%d init fail: lines are low\n", bus->num);
		dev_err(bus->dev, "SDA=%d SCL=%d\n", npcm_i2c_get_SDA(&bus->adap),
			npcm_i2c_get_SCL(&bus->adap));
		return -ENXIO;
	}

	npcm_i2c_int_enable(bus, true);
	return 0;
}

static int __npcm_i2c_init(struct npcm_i2c *bus, struct platform_device *pdev)
{
	u32 clk_freq_hz;
	int ret;

	/* Initialize the internal data structures */
	bus->state = I2C_DISABLE;
	bus->master_or_slave = I2C_SLAVE;
	bus->int_time_stamp = 0;
#if IS_ENABLED(CONFIG_I2C_SLAVE)
	bus->slave = NULL;
#endif

	ret = device_property_read_u32(&pdev->dev, "clock-frequency",
				       &clk_freq_hz);
	if (ret) {
		dev_info(&pdev->dev, "Could not read clock-frequency property");
		clk_freq_hz = I2C_MAX_STANDARD_MODE_FREQ;
	}

	ret = npcm_i2c_init_module(bus, I2C_MASTER, clk_freq_hz);
	if (ret) {
		dev_err(&pdev->dev, "npcm_i2c_init_module failed\n");
		return ret;
	}

	return 0;
}

static irqreturn_t npcm_i2c_bus_irq(int irq, void *dev_id)
{
	struct npcm_i2c *bus = dev_id;

	if (npcm_i2c_is_master(bus))
		bus->master_or_slave = I2C_MASTER;

	if (bus->master_or_slave == I2C_MASTER) {
		bus->int_time_stamp = jiffies;
		if (!npcm_i2c_int_master_handler(bus))
			return IRQ_HANDLED;
	}
#if IS_ENABLED(CONFIG_I2C_SLAVE)
	if (bus->slave) {
		bus->master_or_slave = I2C_SLAVE;
		if (npcm_i2c_int_slave_handler(bus))
			return IRQ_HANDLED;
	}
#endif
	/* Clear status bits for spurious interrupts */
	npcm_i2c_clear_master_status(bus);

	return IRQ_HANDLED;
}

static bool npcm_i2c_master_start_xmit(struct npcm_i2c *bus,
				       u8 slave_addr, u16 nwrite, u16 nread,
				       u8 *write_data, u8 *read_data,
				       bool use_PEC, bool use_read_block)
{
	if (bus->state != I2C_IDLE) {
		bus->cmd_err = -EBUSY;
		return false;
	}
	bus->dest_addr = slave_addr << 1;
	bus->wr_buf = write_data;
	bus->wr_size = nwrite;
	bus->wr_ind = 0;
	bus->rd_buf = read_data;
	bus->rd_size = nread;
	bus->rd_ind = 0;
	bus->PEC_use = 0;

	/* for tx PEC is appended to buffer from i2c IF. PEC flag is ignored */
	if (nread)
		bus->PEC_use = use_PEC;

	bus->read_block_use = use_read_block;
	if (nread && !nwrite)
		bus->operation = I2C_READ_OPER;
	else
		bus->operation = I2C_WRITE_OPER;
	if (bus->fifo_use) {
		u8 i2cfif_cts;

		npcm_i2c_select_bank(bus, I2C_BANK_1);
		/* clear FIFO and relevant status bits. */
		i2cfif_cts = ioread8(bus->reg + NPCM_I2CFIF_CTS);
		i2cfif_cts &= ~NPCM_I2CFIF_CTS_SLVRSTR;
		i2cfif_cts |= NPCM_I2CFIF_CTS_CLR_FIFO;
		iowrite8(i2cfif_cts, bus->reg + NPCM_I2CFIF_CTS);
	}

	bus->state = I2C_IDLE;
	npcm_i2c_stall_after_start(bus, true);
	npcm_i2c_master_start(bus);
	return true;
}

static int npcm_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
				int num)
{
	struct npcm_i2c *bus = container_of(adap, struct npcm_i2c, adap);
	struct i2c_msg *msg0, *msg1;
	unsigned long time_left, flags;
	u16 nwrite, nread;
	u8 *write_data, *read_data;
	u8 slave_addr;
	unsigned long timeout;
	bool read_block = false;
	bool read_PEC = false;
	u8 bus_busy;
	unsigned long timeout_usec;

	if (bus->state == I2C_DISABLE) {
		dev_err(bus->dev, "I2C%d module is disabled", bus->num);
		return -EINVAL;
	}

	msg0 = &msgs[0];
	slave_addr = msg0->addr;
	if (msg0->flags & I2C_M_RD) { /* read */
		nwrite = 0;
		write_data = NULL;
		read_data = msg0->buf;
		if (msg0->flags & I2C_M_RECV_LEN) {
			nread = 1;
			read_block = true;
			if (msg0->flags & I2C_CLIENT_PEC)
				read_PEC = true;
		} else {
			nread = msg0->len;
		}
	} else { /* write */
		nwrite = msg0->len;
		write_data = msg0->buf;
		nread = 0;
		read_data = NULL;
		if (num == 2) {
			msg1 = &msgs[1];
			read_data = msg1->buf;
			if (msg1->flags & I2C_M_RECV_LEN) {
				nread = 1;
				read_block = true;
				if (msg1->flags & I2C_CLIENT_PEC)
					read_PEC = true;
			} else {
				nread = msg1->len;
				read_block = false;
			}
		}
	}

	/*
	 * Adaptive TimeOut: estimated time in usec + 100% margin:
	 * 2: double the timeout for clock stretching case
	 * 9: bits per transaction (including the ack/nack)
	 */
	timeout_usec = (2 * 9 * USEC_PER_SEC / bus->bus_freq) * (2 + nread + nwrite);
	timeout = max_t(unsigned long, bus->adap.timeout, usecs_to_jiffies(timeout_usec));
	if (nwrite >= 32 * 1024 || nread >= 32 * 1024) {
		dev_err(bus->dev, "i2c%d buffer too big\n", bus->num);
		return -EINVAL;
	}

	time_left = jiffies + timeout + 1;
	do {
		/*
		 * we must clear slave address immediately when the bus is not
		 * busy, so we spinlock it, but we don't keep the lock for the
		 * entire while since it is too long.
		 */
		spin_lock_irqsave(&bus->lock, flags);
		bus_busy = ioread8(bus->reg + NPCM_I2CCST) & NPCM_I2CCST_BB;
#if IS_ENABLED(CONFIG_I2C_SLAVE)
		if (!bus_busy && bus->slave)
			iowrite8((bus->slave->addr & 0x7F),
				 bus->reg + NPCM_I2CADDR1);
#endif
		spin_unlock_irqrestore(&bus->lock, flags);

	} while (time_is_after_jiffies(time_left) && bus_busy);

	if (bus_busy) {
		iowrite8(NPCM_I2CCST_BB, bus->reg + NPCM_I2CCST);
		npcm_i2c_reset(bus);
		i2c_recover_bus(adap);
		return -EAGAIN;
	}

	npcm_i2c_init_params(bus);
	bus->dest_addr = slave_addr;
	bus->msgs = msgs;
	bus->msgs_num = num;
	bus->cmd_err = 0;
	bus->read_block_use = read_block;

	reinit_completion(&bus->cmd_complete);

	npcm_i2c_int_enable(bus, true);

	if (npcm_i2c_master_start_xmit(bus, slave_addr, nwrite, nread,
				       write_data, read_data, read_PEC,
				       read_block)) {
		time_left = wait_for_completion_timeout(&bus->cmd_complete,
							timeout);

		if (time_left == 0) {
			if (bus->timeout_cnt < ULLONG_MAX)
				bus->timeout_cnt++;
			if (bus->master_or_slave == I2C_MASTER) {
				i2c_recover_bus(adap);
				bus->cmd_err = -EIO;
				bus->state = I2C_IDLE;
			}
		}
	}

	/* if there was BER, check if need to recover the bus: */
	if (bus->cmd_err == -EAGAIN)
		bus->cmd_err = i2c_recover_bus(adap);

	/*
	 * After any type of error, check if LAST bit is still set,
	 * due to a HW issue.
	 * It cannot be cleared without resetting the module.
	 */
	else if (bus->cmd_err &&
		 (bus->data->rxf_ctl_last_pec & ioread8(bus->reg + NPCM_I2CRXF_CTL)))
		npcm_i2c_reset(bus);

	/* After any xfer, successful or not, stall and EOB must be disabled */
	npcm_i2c_stall_after_start(bus, false);
	npcm_i2c_eob_int(bus, false);

#if IS_ENABLED(CONFIG_I2C_SLAVE)
	/* reenable slave if it was enabled */
	if (bus->slave)
		iowrite8((bus->slave->addr & 0x7F) | NPCM_I2CADDR_SAEN,
			 bus->reg + NPCM_I2CADDR1);
#else
	npcm_i2c_int_enable(bus, false);
#endif
	return bus->cmd_err;
}

static u32 npcm_i2c_functionality(struct i2c_adapter *adap)
{
	return I2C_FUNC_I2C |
	       I2C_FUNC_SMBUS_EMUL |
	       I2C_FUNC_SMBUS_BLOCK_DATA |
	       I2C_FUNC_SMBUS_PEC |
	       I2C_FUNC_SLAVE;
}

static const struct i2c_adapter_quirks npcm_i2c_quirks = {
	.max_read_len = 32768,
	.max_write_len = 32768,
	.flags = I2C_AQ_COMB_WRITE_THEN_READ,
};

static const struct i2c_algorithm npcm_i2c_algo = {
	.master_xfer = npcm_i2c_master_xfer,
	.functionality = npcm_i2c_functionality,
#if IS_ENABLED(CONFIG_I2C_SLAVE)
	.reg_slave	= npcm_i2c_reg_slave,
	.unreg_slave	= npcm_i2c_unreg_slave,
#endif
};

/* i2c debugfs directory: used to keep health monitor of i2c devices */
static struct dentry *npcm_i2c_debugfs_dir;

static void npcm_i2c_init_debugfs(struct platform_device *pdev,
				  struct npcm_i2c *bus)
{
	struct dentry *d;

	if (!npcm_i2c_debugfs_dir)
		return;
	d = debugfs_create_dir(dev_name(&pdev->dev), npcm_i2c_debugfs_dir);
	if (IS_ERR_OR_NULL(d))
		return;
	debugfs_create_u64("ber_cnt", 0444, d, &bus->ber_cnt);
	debugfs_create_u64("nack_cnt", 0444, d, &bus->nack_cnt);
	debugfs_create_u64("rec_succ_cnt", 0444, d, &bus->rec_succ_cnt);
	debugfs_create_u64("rec_fail_cnt", 0444, d, &bus->rec_fail_cnt);
	debugfs_create_u64("timeout_cnt", 0444, d, &bus->timeout_cnt);
	debugfs_create_u64("tx_complete_cnt", 0444, d, &bus->tx_complete_cnt);

	bus->debugfs = d;
}

static int npcm_i2c_probe_bus(struct platform_device *pdev)
{
	struct device_node *np = pdev->dev.of_node;
	static struct regmap *gcr_regmap;
	struct device *dev = &pdev->dev;
	struct i2c_adapter *adap;
	struct npcm_i2c *bus;
	struct clk *i2c_clk;
	int irq;
	int ret;

	bus = devm_kzalloc(&pdev->dev, sizeof(*bus), GFP_KERNEL);
	if (!bus)
		return -ENOMEM;

	bus->dev = &pdev->dev;

	bus->data = of_device_get_match_data(dev);
	if (!bus->data) {
		dev_err(dev, "OF data missing\n");
		return -EINVAL;
	}

	bus->num = of_alias_get_id(pdev->dev.of_node, "i2c");
	/* core clk must be acquired to calculate module timing settings */
	i2c_clk = devm_clk_get(&pdev->dev, NULL);
	if (IS_ERR(i2c_clk))
		return PTR_ERR(i2c_clk);
	bus->apb_clk = clk_get_rate(i2c_clk);

	gcr_regmap = syscon_regmap_lookup_by_phandle(np, "nuvoton,sys-mgr");
	if (IS_ERR(gcr_regmap))
		gcr_regmap = syscon_regmap_lookup_by_compatible("nuvoton,npcm750-gcr");

	if (IS_ERR(gcr_regmap))
		return PTR_ERR(gcr_regmap);
	regmap_write(gcr_regmap, NPCM_I2CSEGCTL, bus->data->segctl_init_val);

	bus->reg = devm_platform_ioremap_resource(pdev, 0);
	if (IS_ERR(bus->reg))
		return PTR_ERR(bus->reg);

	spin_lock_init(&bus->lock);
	init_completion(&bus->cmd_complete);

	adap = &bus->adap;
	adap->owner = THIS_MODULE;
	adap->retries = 3;
	adap->timeout = msecs_to_jiffies(35);
	adap->algo = &npcm_i2c_algo;
	adap->quirks = &npcm_i2c_quirks;
	adap->algo_data = bus;
	adap->dev.parent = &pdev->dev;
	adap->dev.of_node = pdev->dev.of_node;
	adap->nr = pdev->id;

	irq = platform_get_irq(pdev, 0);
	if (irq < 0)
		return irq;

	ret = devm_request_irq(bus->dev, irq, npcm_i2c_bus_irq, 0,
			       dev_name(bus->dev), bus);
	if (ret)
		return ret;

	ret = __npcm_i2c_init(bus, pdev);
	if (ret)
		return ret;

	npcm_i2c_recovery_init(adap);

	i2c_set_adapdata(adap, bus);

	snprintf(bus->adap.name, sizeof(bus->adap.name), "npcm_i2c_%d",
		 bus->num);
	ret = i2c_add_numbered_adapter(&bus->adap);
	if (ret)
		return ret;

	platform_set_drvdata(pdev, bus);
	npcm_i2c_init_debugfs(pdev, bus);
	return 0;
}

static int npcm_i2c_remove_bus(struct platform_device *pdev)
{
	unsigned long lock_flags;
	struct npcm_i2c *bus = platform_get_drvdata(pdev);

	debugfs_remove_recursive(bus->debugfs);
	spin_lock_irqsave(&bus->lock, lock_flags);
	npcm_i2c_disable(bus);
	spin_unlock_irqrestore(&bus->lock, lock_flags);
	i2c_del_adapter(&bus->adap);
	return 0;
}

static const struct of_device_id npcm_i2c_bus_of_table[] = {
	{ .compatible = "nuvoton,npcm750-i2c", .data = &npxm7xx_i2c_data },
	{ .compatible = "nuvoton,npcm845-i2c", .data = &npxm8xx_i2c_data },
	{}
};
MODULE_DEVICE_TABLE(of, npcm_i2c_bus_of_table);

static struct platform_driver npcm_i2c_bus_driver = {
	.probe = npcm_i2c_probe_bus,
	.remove = npcm_i2c_remove_bus,
	.driver = {
		.name = "nuvoton-i2c",
		.of_match_table = npcm_i2c_bus_of_table,
	}
};

static int __init npcm_i2c_init(void)
{
	int ret;

	npcm_i2c_debugfs_dir = debugfs_create_dir("npcm_i2c", NULL);

	ret = platform_driver_register(&npcm_i2c_bus_driver);
	if (ret) {
		debugfs_remove_recursive(npcm_i2c_debugfs_dir);
		return ret;
	}

	return 0;
}
module_init(npcm_i2c_init);

static void __exit npcm_i2c_exit(void)
{
	platform_driver_unregister(&npcm_i2c_bus_driver);
	debugfs_remove_recursive(npcm_i2c_debugfs_dir);
}
module_exit(npcm_i2c_exit);

MODULE_AUTHOR("Avi Fishman <avi.fishman@gmail.com>");
MODULE_AUTHOR("Tali Perry <tali.perry@nuvoton.com>");
MODULE_AUTHOR("Tyrone Ting <kfting@nuvoton.com>");
MODULE_DESCRIPTION("Nuvoton I2C Bus Driver");
MODULE_LICENSE("GPL v2");