New upstream version 1.6.0+dfsgupstream/1.6.0+dfsg

1 files changed, 143 insertions, 0 deletions

diff --git a/conf.d/stream.conf b/conf.d/stream.conf
new file mode 100644
index 00000000..0ebdccb8
--- /dev/null
+++ b/conf.d/stream.conf
@@ -0,0 +1,143 @@
+# netdata configuration for aggregating data from remote hosts
+#
+# API keys authorize a pair of sending-receiving netdata servers.
+# Once their communication is authorized, they can exchange metrics for any
+# number of hosts.
+#
+# You can generate API keys, with the linux command: uuidgen
+#
+# -----------------------------------------------------------------------------
+# 1. ON SLAVE NETDATA - THE ONE THAT WILL BE SENDING METRICS
+
+[stream]
+    # Enable this on slaves, to have them send metrics.
+	enabled = no
+
+	# The destination to send metrics to.
+	# A space separated list of:
+	#         [PROTOCOL:]HOST[%INTERFACE][:PORT]
+	# The first available will get the metrics.
+	# PROTOCOL = tcp or udp (only tcp is supported by masters)
+	# HOST = an IPv4, IPv6 IP, or a hostname.
+	#        IPv6 IPs should be given with brackets [ip:address]
+	# INTERFACE = the network interface to use
+	# PORT = the port number or service name (/etc/services)
+	# This communication is not HTTP (cannot be proxied by web proxies).
+	destination =
+
+	# The API_KEY to use (as the sender)
+	api key =
+
+    # The timeout to connect and send metrics
+	timeout seconds = 60
+
+	# If the destination line above does specify a port, use this
+	default port = 19999
+
+	# The buffer to use for sending metrics.
+	# 1MB by default is good for 2-3 seconds of data, so increase this
+	# if you expect latencies.
+	buffer size bytes = 1048576
+
+	# If the connection fails, or it disconnects,
+	# retry after that many seconds.
+	reconnect delay seconds = 5
+
+	# Attempt to sync the clock the of the master with the clock of the
+	# slave for that many iterations, when starting.
+	initial clock resync iterations = 60
+
+
+# -----------------------------------------------------------------------------
+# 2. ON MASTER NETDATA - THE ONE THAT WILL BE RECEIVING METRICS
+#
+#    You can have one API key per slave, or the same API key for all slaves.
+#
+#    All options below are used in this order:
+#
+#    a) MACHINE_GUID (settings for each machine)
+#    b) API_KEY      (settings for the API key)
+#    c) this netdata defaults (as in netdata.conf)
+#
+#    You can combine the above (the more specific setting will be used).
+
+# API key authentication
+# If the key is not listed here, it will not be able to connect.
+
+[API_KEY]
+    # Default settings for the API key
+
+    # You can disable the API key, by setting this to: no
+    # The default (for unknown API keys) is also: no
+    enabled = no
+
+    # The default history in entries, for all hosts using this API key.
+    # You can also set it per host below.
+    # If you don't set it here, the history size of the central netdata
+    # will be used
+    default history = 3600
+
+    # The default memory mode to be used for all hosts using this API key.
+    # You can also set it per host below.
+    # If you don't set it here, the memory mode of netdata.conf will be used.
+    # Valid modes:
+    #    save    save on exit, load on start
+    #    map     like swap (continuously syncing to disks)
+    #    ram     keep it in RAM, don't touch the disk
+    #    none    no database (passing through this netdata)
+    default memory mode = ram
+
+    # Shall we enable health monitoring for the hosts using this API key?
+    # 3 values:
+    #    yes     enable alarms
+    #    no      do not enable alarms
+    #    auto    enable alarms, only when the sending netdata is connected
+    # You can also set it per host, below.
+    # The default is the same as to netdata.conf
+    health enabled by default = auto
+
+    # postpone alarms for a short period after the sender is connected
+    default postpone alarms on connect seconds = 60
+
+    # need to route metrics differently? set these.
+    # the defaults are the ones at the [stream] section
+    #default proxy enabled = yes | no
+    #default proxy destination = IP:PORT IP:PORT ...
+    #default proxy api key = API_KEY
+
+
+# -----------------------------------------------------------------------------
+# 3. ON MASTER NETDATA - THE ONE THAT WILL BE RECEIVING METRICS
+#
+# THIS IS OPTIONAL - YOU DON'T NEED IT BY DEFAULT
+# It only exists to give you finer control of the master settings for each
+# slave host, when the same API key is used by many netdata slaves / proxies.
+#
+# Each netdata has a unique GUID - generated the first time netdata starts.
+# You can find it at /var/lib/netdata/registry/netdata.public.unique.id
+# The host sending data will have one. If the host is not ephemeral,
+# you can give settings for each specific host here.
+
+[MACHINE_GUID]
+    # enable this host: yes | no
+    # When disabled, the master will not receive metrics for this host.
+    # THIS IS NOT A SECURITY MECHANISM - AN ATTACKER CAN SET ANY OTHER GUID.
+    # Use only the API key for security.
+    enabled = no
+
+    # The number of entries in the database
+    history = 3600
+
+    # The memory mode of the database: save | map | ram | none
+    memory mode = save
+
+    # Health / alarms control: yes | no | auto
+    health enabled = yes
+
+    # postpone alarms when the sender connects
+    postpone alarms on connect seconds = 60
+
+    # need to route metrics differently?
+    #proxy enabled = yes | no
+    #proxy destination = IP:PORT IP:PORT ...
+    #proxy api key = API_KEY